ARM: dts: add support for Odroid-N2
Import HardKernel Odroid-N2 DT from Linux 5.3-rc1, commit 5f9e832c1370
("Linus 5.3-rc1") based on an Amlogic G12B S922X SoC.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Mark Kettenis <kettenis@openbsd.org>
diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
index b437f75..70a9bc2 100644
--- a/arch/arm/dts/Makefile
+++ b/arch/arm/dts/Makefile
@@ -135,7 +135,8 @@
meson-gxl-s905x-khadas-vim.dtb \
meson-gxm-khadas-vim2.dtb \
meson-axg-s400.dtb \
- meson-g12a-u200.dtb
+ meson-g12a-u200.dtb \
+ meson-g12b-odroid-n2.dtb
dtb-$(CONFIG_TEGRA) += tegra20-harmony.dtb \
tegra20-medcom-wide.dtb \
tegra20-paz00.dtb \
diff --git a/arch/arm/dts/meson-g12b-odroid-n2.dts b/arch/arm/dts/meson-g12b-odroid-n2.dts
new file mode 100644
index 0000000..81780ff
--- /dev/null
+++ b/arch/arm/dts/meson-g12b-odroid-n2.dts
@@ -0,0 +1,386 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2019 BayLibre, SAS
+ * Author: Neil Armstrong <narmstrong@baylibre.com>
+ */
+
+/dts-v1/;
+
+#include "meson-g12b.dtsi"
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/gpio/meson-g12a-gpio.h>
+#include <dt-bindings/sound/meson-g12a-tohdmitx.h>
+
+/ {
+ compatible = "hardkernel,odroid-n2", "amlogic,g12b";
+ model = "Hardkernel ODROID-N2";
+
+ aliases {
+ serial0 = &uart_AO;
+ ethernet0 = ðmac;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ memory@0 {
+ device_type = "memory";
+ reg = <0x0 0x0 0x0 0x40000000>;
+ };
+
+ emmc_pwrseq: emmc-pwrseq {
+ compatible = "mmc-pwrseq-emmc";
+ reset-gpios = <&gpio BOOT_12 GPIO_ACTIVE_LOW>;
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ blue {
+ label = "n2:blue";
+ gpios = <&gpio_ao GPIOAO_11 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "heartbeat";
+ };
+ };
+
+ tflash_vdd: regulator-tflash_vdd {
+ compatible = "regulator-fixed";
+
+ regulator-name = "TFLASH_VDD";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+
+ gpio = <&gpio_ao GPIOAO_8 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+
+ tf_io: gpio-regulator-tf_io {
+ compatible = "regulator-gpio";
+
+ regulator-name = "TF_IO";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+
+ gpios = <&gpio_ao GPIOAO_9 GPIO_ACTIVE_HIGH>;
+ gpios-states = <0>;
+
+ states = <3300000 0
+ 1800000 1>;
+ };
+
+ flash_1v8: regulator-flash_1v8 {
+ compatible = "regulator-fixed";
+ regulator-name = "FLASH_1V8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ vin-supply = <&vcc_3v3>;
+ regulator-always-on;
+ };
+
+ main_12v: regulator-main_12v {
+ compatible = "regulator-fixed";
+ regulator-name = "12V";
+ regulator-min-microvolt = <12000000>;
+ regulator-max-microvolt = <12000000>;
+ regulator-always-on;
+ };
+
+ vcc_5v: regulator-vcc_5v {
+ compatible = "regulator-fixed";
+ regulator-name = "5V";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-always-on;
+ vin-supply = <&main_12v>;
+ };
+
+ vcc_1v8: regulator-vcc_1v8 {
+ compatible = "regulator-fixed";
+ regulator-name = "VCC_1V8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ vin-supply = <&vcc_3v3>;
+ regulator-always-on;
+ };
+
+ vcc_3v3: regulator-vcc_3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "VCC_3V3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ vin-supply = <&vddao_3v3>;
+ regulator-always-on;
+ /* FIXME: actually controlled by VDDCPU_B_EN */
+ };
+
+ hub_5v: regulator-hub_5v {
+ compatible = "regulator-fixed";
+ regulator-name = "HUB_5V";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ vin-supply = <&vcc_5v>;
+
+ /* Connected to the Hub CHIPENABLE, LOW sets low power state */
+ gpio = <&gpio GPIOH_5 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+
+ usb_pwr_en: regulator-usb_pwr_en {
+ compatible = "regulator-fixed";
+ regulator-name = "USB_PWR_EN";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ vin-supply = <&vcc_5v>;
+
+ /* Connected to the microUSB port power enable */
+ gpio = <&gpio GPIOH_6 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+
+ vddao_1v8: regulator-vddao_1v8 {
+ compatible = "regulator-fixed";
+ regulator-name = "VDDAO_1V8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ vin-supply = <&vddao_3v3>;
+ regulator-always-on;
+ };
+
+ vddao_3v3: regulator-vddao_3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "VDDAO_3V3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ vin-supply = <&main_12v>;
+ regulator-always-on;
+ };
+
+ hdmi-connector {
+ compatible = "hdmi-connector";
+ type = "a";
+
+ port {
+ hdmi_connector_in: endpoint {
+ remote-endpoint = <&hdmi_tx_tmds_out>;
+ };
+ };
+ };
+
+ sound {
+ compatible = "amlogic,axg-sound-card";
+ model = "G12A-ODROIDN2";
+ audio-aux-devs = <&tdmout_b>;
+ audio-routing = "TDMOUT_B IN 0", "FRDDR_A OUT 1",
+ "TDMOUT_B IN 1", "FRDDR_B OUT 1",
+ "TDMOUT_B IN 2", "FRDDR_C OUT 1",
+ "TDM_B Playback", "TDMOUT_B OUT";
+
+ assigned-clocks = <&clkc CLKID_MPLL2>,
+ <&clkc CLKID_MPLL0>,
+ <&clkc CLKID_MPLL1>;
+ assigned-clock-parents = <0>, <0>, <0>;
+ assigned-clock-rates = <294912000>,
+ <270950400>,
+ <393216000>;
+ status = "okay";
+
+ dai-link-0 {
+ sound-dai = <&frddr_a>;
+ };
+
+ dai-link-1 {
+ sound-dai = <&frddr_b>;
+ };
+
+ dai-link-2 {
+ sound-dai = <&frddr_c>;
+ };
+
+ /* 8ch hdmi interface */
+ dai-link-3 {
+ sound-dai = <&tdmif_b>;
+ dai-format = "i2s";
+ dai-tdm-slot-tx-mask-0 = <1 1>;
+ dai-tdm-slot-tx-mask-1 = <1 1>;
+ dai-tdm-slot-tx-mask-2 = <1 1>;
+ dai-tdm-slot-tx-mask-3 = <1 1>;
+ mclk-fs = <256>;
+
+ codec {
+ sound-dai = <&tohdmitx TOHDMITX_I2S_IN_B>;
+ };
+ };
+
+ /* hdmi glue */
+ dai-link-4 {
+ sound-dai = <&tohdmitx TOHDMITX_I2S_OUT>;
+
+ codec {
+ sound-dai = <&hdmi_tx>;
+ };
+ };
+ };
+};
+
+&arb {
+ status = "okay";
+};
+
+&cec_AO {
+ pinctrl-0 = <&cec_ao_a_h_pins>;
+ pinctrl-names = "default";
+ status = "disabled";
+ hdmi-phandle = <&hdmi_tx>;
+};
+
+&cecb_AO {
+ pinctrl-0 = <&cec_ao_b_h_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+ hdmi-phandle = <&hdmi_tx>;
+};
+
+&clkc_audio {
+ status = "okay";
+};
+
+&ext_mdio {
+ external_phy: ethernet-phy@0 {
+ /* Realtek RTL8211F (0x001cc916) */
+ reg = <0>;
+ max-speed = <1000>;
+
+ reset-assert-us = <10000>;
+ reset-deassert-us = <30000>;
+ reset-gpios = <&gpio GPIOZ_15 (GPIO_ACTIVE_LOW | GPIO_OPEN_DRAIN)>;
+
+ interrupt-parent = <&gpio_intc>;
+ /* MAC_INTR on GPIOZ_14 */
+ interrupts = <26 IRQ_TYPE_LEVEL_LOW>;
+ };
+};
+
+ðmac {
+ pinctrl-0 = <ð_pins>, <ð_rgmii_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+ phy-mode = "rgmii";
+ phy-handle = <&external_phy>;
+ amlogic,tx-delay-ns = <2>;
+};
+
+&frddr_a {
+ status = "okay";
+};
+
+&frddr_b {
+ status = "okay";
+};
+
+&frddr_c {
+ status = "okay";
+};
+
+&gpio {
+ /*
+ * WARNING: The USB Hub on the Odroid-N2 needs a reset signal
+ * to be turned high in order to be detected by the USB Controller
+ * This signal should be handled by a USB specific power sequence
+ * in order to reset the Hub when USB bus is powered down.
+ */
+ usb-hub {
+ gpio-hog;
+ gpios = <GPIOH_4 GPIO_ACTIVE_HIGH>;
+ output-high;
+ line-name = "usb-hub-reset";
+ };
+};
+
+&hdmi_tx {
+ status = "okay";
+ pinctrl-0 = <&hdmitx_hpd_pins>, <&hdmitx_ddc_pins>;
+ pinctrl-names = "default";
+ hdmi-supply = <&vcc_5v>;
+};
+
+&hdmi_tx_tmds_port {
+ hdmi_tx_tmds_out: endpoint {
+ remote-endpoint = <&hdmi_connector_in>;
+ };
+};
+
+&ir {
+ status = "okay";
+ pinctrl-0 = <&remote_input_ao_pins>;
+ pinctrl-names = "default";
+};
+
+/* SD card */
+&sd_emmc_b {
+ status = "okay";
+ pinctrl-0 = <&sdcard_c_pins>;
+ pinctrl-1 = <&sdcard_clk_gate_c_pins>;
+ pinctrl-names = "default", "clk-gate";
+
+ bus-width = <4>;
+ cap-sd-highspeed;
+ max-frequency = <50000000>;
+ disable-wp;
+
+ cd-gpios = <&gpio GPIOC_6 GPIO_ACTIVE_LOW>;
+ vmmc-supply = <&tflash_vdd>;
+ vqmmc-supply = <&tf_io>;
+
+};
+
+/* eMMC */
+&sd_emmc_c {
+ status = "okay";
+ pinctrl-0 = <&emmc_pins>, <&emmc_ds_pins>;
+ pinctrl-1 = <&emmc_clk_gate_pins>;
+ pinctrl-names = "default", "clk-gate";
+
+ bus-width = <8>;
+ cap-mmc-highspeed;
+ mmc-ddr-1_8v;
+ mmc-hs200-1_8v;
+ max-frequency = <200000000>;
+ disable-wp;
+
+ mmc-pwrseq = <&emmc_pwrseq>;
+ vmmc-supply = <&vcc_3v3>;
+ vqmmc-supply = <&flash_1v8>;
+};
+
+&tdmif_b {
+ status = "okay";
+};
+
+&tdmout_b {
+ status = "okay";
+};
+
+&tohdmitx {
+ status = "okay";
+};
+
+&uart_AO {
+ status = "okay";
+ pinctrl-0 = <&uart_ao_a_pins>;
+ pinctrl-names = "default";
+};
+
+&usb {
+ status = "okay";
+ vbus-supply = <&usb_pwr_en>;
+};
+
+&usb2_phy0 {
+ phy-supply = <&vcc_5v>;
+};
+
+&usb2_phy1 {
+ /* Enable the hub which is connected to this port */
+ phy-supply = <&hub_5v>;
+};
diff --git a/arch/arm/dts/meson-g12b.dtsi b/arch/arm/dts/meson-g12b.dtsi
new file mode 100644
index 0000000..9e88e51
--- /dev/null
+++ b/arch/arm/dts/meson-g12b.dtsi
@@ -0,0 +1,82 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2019 BayLibre, SAS
+ * Author: Neil Armstrong <narmstrong@baylibre.com>
+ */
+
+#include "meson-g12a.dtsi"
+
+/ {
+ compatible = "amlogic,g12b";
+
+ cpus {
+ cpu-map {
+ cluster0 {
+ core0 {
+ cpu = <&cpu0>;
+ };
+
+ core1 {
+ cpu = <&cpu1>;
+ };
+ };
+
+ cluster1 {
+ core0 {
+ cpu = <&cpu100>;
+ };
+
+ core1 {
+ cpu = <&cpu101>;
+ };
+
+ core2 {
+ cpu = <&cpu102>;
+ };
+
+ core3 {
+ cpu = <&cpu103>;
+ };
+ };
+ };
+
+ /delete-node/ cpu@2;
+ /delete-node/ cpu@3;
+
+ cpu100: cpu@100 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a73";
+ reg = <0x0 0x100>;
+ enable-method = "psci";
+ next-level-cache = <&l2>;
+ };
+
+ cpu101: cpu@101 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a73";
+ reg = <0x0 0x101>;
+ enable-method = "psci";
+ next-level-cache = <&l2>;
+ };
+
+ cpu102: cpu@102 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a73";
+ reg = <0x0 0x102>;
+ enable-method = "psci";
+ next-level-cache = <&l2>;
+ };
+
+ cpu103: cpu@103 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a73";
+ reg = <0x0 0x103>;
+ enable-method = "psci";
+ next-level-cache = <&l2>;
+ };
+ };
+};
+
+&clkc {
+ compatible = "amlogic,g12b-clkc";
+};