pxa: add support for palmtreo680 board

This patch adds support for the Palm Treo 680 smartphone.  A quick overview of
u-boot implementation on the treo 680...

The treo 680 has a Diskonchip G4 nand flash chip.  This device has a 2k region
that maps to the system bus at the reset vector in a NOR-like fashion so that it
can be used as the boot device.  The phone is shipped with this 2k region
configured as write-protected (can't be modified) and programmed with an initial
program loader (IPL).  At power-up, this IPL loads the contents of two flash
blocks to SDRAM and jumps to it.  The capacity of the two blocks is not large
enough to hold all of u-boot, so a u-boot SPL is used.  To conserve flash space,
these two blocks and the necessary number of subsequent blocks are programmed
with a concatenated spl + u-boot image.  That way, the IPL will also load a
portion of u-boot proper, and when the spl runs, it relocates the portion of
u-boot that the IPL has already loaded, and then resumes loading the remaining
part of u-boot before jumping to it.

The default_environment is used (CONFIG_ENV_IS_NOWHERE) because I didn't think
that having a writable environment was worth the cost of a flash block, although
adding it would be straightforward.  I abuse the CONFIG_EXTRA_ENV_SETTINGS
option to specify the usbtty for the console (CONFIG_SYS_CONSOLE_IS_IN_ENV).

Support for the LCD is included, but currently it is only useful for displaying
the u-boot splash screen.  But if u-boot is built without the usbtty console, it
does display the auto-boot progress nicely.

Signed-off-by: Mike Dunn <mikedunn@newsguy.com>
diff --git a/include/configs/palmtreo680.h b/include/configs/palmtreo680.h
new file mode 100644
index 0000000..2ab6fd2
--- /dev/null
+++ b/include/configs/palmtreo680.h
@@ -0,0 +1,286 @@
+/*
+ * Palm Treo 680 configuration file
+ *
+ * Copyright (C) 2013 Mike Dunn <mikedunn@newsguy.com>
+ *
+ * This file is released under the terms of GPL v2 and any later version.
+ * See the file COPYING in the root directory of the source tree for details.
+ *
+ */
+
+#ifndef	__CONFIG_H
+#define	__CONFIG_H
+
+/*
+ * High Level Board Configuration Options
+ */
+#define CONFIG_CPU_PXA27X
+#define CONFIG_PALMTREO680
+#define CONFIG_MACH_TYPE                MACH_TYPE_TREO680
+
+#define CONFIG_SYS_MALLOC_LEN           (4096*1024)
+
+#define CONFIG_LZMA
+
+/*
+ * Serial Console Configuration
+ */
+#define CONFIG_PXA_SERIAL
+#define CONFIG_FFUART                   1
+#define CONFIG_BAUDRATE                 9600
+#define CONFIG_SYS_BAUDRATE_TABLE       { 9600, 19200, 38400, 57600, 115200 }
+#define CONFIG_CONS_INDEX               3
+
+/* we have nand (although technically nand *is* flash...) */
+#define CONFIG_SYS_NO_FLASH
+
+#define CONFIG_LCD
+/* #define CONFIG_KEYBOARD */  /* TODO */
+
+/*
+ * Bootloader Components Configuration
+ */
+#include <config_cmd_default.h>
+#undef  CONFIG_CMD_FPGA
+#undef  CONFIG_CMD_LOADS
+#undef  CONFIG_CMD_NET
+#undef  CONFIG_CMD_NFS
+#undef  CONFIG_CMD_IMLS
+#undef  CONFIG_CMD_FLASH
+#undef  CONFIG_CMD_SETGETDCR
+#undef  CONFIG_CMD_SOURCE
+#undef  CONFIG_CMD_XIMG
+
+#define CONFIG_CMD_ENV
+#define CONFIG_CMD_MMC
+#define CONFIG_CMD_NAND
+
+#define CONFIG_CMDLINE_TAG
+#define CONFIG_SETUP_MEMORY_TAGS
+
+/*
+ * MMC Card Configuration
+ */
+#ifdef CONFIG_CMD_MMC
+#define CONFIG_MMC
+#define CONFIG_GENERIC_MMC
+#define CONFIG_PXA_MMC_GENERIC
+
+#define CONFIG_CMD_FAT
+#define CONFIG_CMD_EXT2
+#define CONFIG_DOS_PARTITION
+#endif
+
+/*
+ * LCD
+ */
+#ifdef CONFIG_LCD
+#define CONFIG_PXA_LCD
+#define CONFIG_ACX544AKN
+#define CONFIG_LCD_LOGO
+#define CONFIG_SYS_LCD_PXA_NO_L_BIAS /* don't configure GPIO77 as L_BIAS */
+#define LCD_BPP LCD_COLOR16
+#define CONFIG_FB_ADDR 0x5c000000    /* internal SRAM */
+#define CONFIG_CMD_BMP
+#define CONFIG_SPLASH_SCREEN         /* requires "splashimage" env var */
+#define CONFIG_SPLASH_SCREEN_ALIGN   /* requires "splashpos" env var */
+#define CONFIG_VIDEO_BMP_GZIP
+#define CONFIG_SYS_VIDEO_LOGO_MAX_SIZE  (2 << 20)
+
+#endif
+
+/*
+ * KGDB
+ */
+#ifdef CONFIG_CMD_KGDB
+#define CONFIG_KGDB_BAUDRATE            230400  /* kgdb serial port speed */
+#define CONFIG_KGDB_SER_INDEX           2       /* which serial port to use */
+#endif
+
+/*
+ * HUSH Shell Configuration
+ */
+#define CONFIG_SYS_HUSH_PARSER          1
+#define CONFIG_SYS_PROMPT_HUSH_PS2      "> "
+
+#define CONFIG_SYS_LONGHELP
+#ifdef CONFIG_SYS_HUSH_PARSER
+#define CONFIG_SYS_PROMPT               "$ "
+#else
+#define CONFIG_SYS_PROMPT               "=> "
+#endif
+#define CONFIG_SYS_CBSIZE               256
+#define CONFIG_SYS_PBSIZE               \
+	(CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16)
+#define CONFIG_SYS_MAXARGS              16
+#define CONFIG_SYS_BARGSIZE             CONFIG_SYS_CBSIZE
+#define CONFIG_SYS_DEVICE_NULLDEV       1
+
+/*
+ * Clock Configuration
+ */
+#undef  CONFIG_SYS_CLKS_IN_HZ
+#define CONFIG_SYS_HZ                   1000 /* decrementer freq: 1 ms ticks */
+#define CONFIG_SYS_CPUSPEED             0x210           /* 416MHz ; N=2,L=16 */
+
+/*
+ * Stack sizes
+ */
+#define CONFIG_STACKSIZE                (128*1024)      /* regular stack */
+#ifdef CONFIG_USE_IRQ
+#define CONFIG_STACKSIZE_IRQ            (4*1024)        /* IRQ stack */
+#define CONFIG_STACKSIZE_FIQ            (4*1024)        /* FIQ stack */
+#endif
+
+/*
+ * DRAM Map
+ */
+#define CONFIG_NR_DRAM_BANKS            1               /* 1 bank of DRAM */
+#define PHYS_SDRAM_1                    0xa0000000      /* SDRAM Bank #1 */
+#define PHYS_SDRAM_1_SIZE               0x04000000      /* 64 MB */
+
+#define CONFIG_SYS_DRAM_BASE            0xa0000000
+#define CONFIG_SYS_DRAM_SIZE            0x04000000      /* 64 MB DRAM */
+
+#define CONFIG_SYS_MEMTEST_START        0xa0400000      /* memtest works on */
+#define CONFIG_SYS_MEMTEST_END          0xa0800000      /* 4 ... 8 MB in DRAM */
+#define CONFIG_SYS_LOAD_ADDR            CONFIG_SYS_DRAM_BASE
+#define CONFIG_SYS_SDRAM_BASE           PHYS_SDRAM_1
+
+/*
+ * GPIO settings
+ */
+#define CONFIG_SYS_GAFR0_L_VAL  0x0E000000
+#define CONFIG_SYS_GAFR0_U_VAL  0xA500001A
+#define CONFIG_SYS_GAFR1_L_VAL  0x60000002
+#define CONFIG_SYS_GAFR1_U_VAL  0xAAA07959
+#define CONFIG_SYS_GAFR2_L_VAL  0x02AAAAAA
+#define CONFIG_SYS_GAFR2_U_VAL  0x41440F08
+#define CONFIG_SYS_GAFR3_L_VAL  0x56AA95FF
+#define CONFIG_SYS_GAFR3_U_VAL  0x00001401
+#define CONFIG_SYS_GPCR0_VAL    0x1FF80400
+#define CONFIG_SYS_GPCR1_VAL    0x03003FC1
+#define CONFIG_SYS_GPCR2_VAL    0x01C1E000
+#define CONFIG_SYS_GPCR3_VAL    0x01C1E000
+#define CONFIG_SYS_GPDR0_VAL    0xCFF90400
+#define CONFIG_SYS_GPDR1_VAL    0xFB22BFC1
+#define CONFIG_SYS_GPDR2_VAL    0x93CDFFDF
+#define CONFIG_SYS_GPDR3_VAL    0x0069FF81
+#define CONFIG_SYS_GPSR0_VAL    0x02000018
+#define CONFIG_SYS_GPSR1_VAL    0x00000000
+#define CONFIG_SYS_GPSR2_VAL    0x000C0000
+#define CONFIG_SYS_GPSR3_VAL    0x00080000
+
+#define CONFIG_SYS_PSSR_VAL     0x30
+
+/*
+ * Clock settings
+ */
+#define CONFIG_SYS_CKEN         0x01ffffff
+#define CONFIG_SYS_CCCR         0x02000210
+
+/*
+ * Memory settings
+ */
+#define CONFIG_SYS_MSC0_VAL     0x7ff844c8
+#define CONFIG_SYS_MSC1_VAL     0x7ff86ab4
+#define CONFIG_SYS_MSC2_VAL     0x7ff87ff8
+#define CONFIG_SYS_MDCNFG_VAL   0x0B880acd
+#define CONFIG_SYS_MDREFR_VAL   0x201fa031
+#define CONFIG_SYS_MDMRS_VAL    0x00320032
+#define CONFIG_SYS_FLYCNFG_VAL  0x00000000
+#define CONFIG_SYS_SXCNFG_VAL   0x40044004
+#define CONFIG_SYS_MECR_VAL     0x00000003
+#define CONFIG_SYS_MCMEM0_VAL   0x0001c391
+#define CONFIG_SYS_MCMEM1_VAL   0x0001c391
+#define CONFIG_SYS_MCATT0_VAL   0x0001c391
+#define CONFIG_SYS_MCATT1_VAL   0x0001c391
+#define CONFIG_SYS_MCIO0_VAL    0x00014611
+#define CONFIG_SYS_MCIO1_VAL    0x0001c391
+
+/*
+ * USB
+ */
+#define CONFIG_USB_DEVICE
+#define CONFIG_USB_TTY
+#define CONFIG_USB_DEV_PULLUP_GPIO 114
+
+/*
+ * SPL
+ */
+#define CONFIG_SPL
+#define CONFIG_SPL_TEXT_BASE    0xa1700000 /* IPL loads SPL here */
+#define CONFIG_SPL_STACK        0x5c040000 /* end of internal SRAM */
+#define CONFIG_SPL_NAND_SUPPORT /* build libnand for spl */
+#define CONFIG_SPL_NAND_DOCG4   /* use lean docg4 nand spl driver */
+#define CONFIG_SPL_LIBGENERIC_SUPPORT  /* spl uses memcpy */
+
+/*
+ * NAND
+ */
+#define CONFIG_NAND_DOCG4
+#define CONFIG_SYS_NAND_SELF_INIT
+#define CONFIG_SYS_MAX_NAND_DEVICE 1 /* only one device */
+#define CONFIG_SYS_NAND_BASE 0x00000000 /* mapped to reset vector */
+#define CONFIG_SYS_NAND_PAGE_SIZE 0x200
+#define CONFIG_SYS_NAND_BLOCK_SIZE 0x40000
+#define CONFIG_BITREVERSE       /* needed by docg4 driver */
+#define CONFIG_BCH              /* needed by docg4 driver */
+
+/*
+ * IMPORTANT NOTE: this is the size of the concatenated spl + u-boot image.  It
+ * will be rounded up to the next 64k boundary (the spl flash block size), so it
+ * does not have to be exact, but you must ensure that it is not less than the
+ * actual image size, or it may fail to boot (bricked phone)!
+ * (Tip: reduces to three blocks with lcd and mmc support removed from u-boot.)
+*/
+#define CONFIG_SYS_NAND_U_BOOT_SIZE 0x40000 /* four 64k flash blocks */
+
+/*
+ * This is the byte offset into the flash at which the concatenated spl + u-boot
+ * image is placed.  It must be at the start of a block (256k boundary).  Blocks
+ * 0 - 5 are write-protected, so we start at block 6.
+ */
+#define CONFIG_SYS_NAND_U_BOOT_OFFS 0x180000  /* block 6 */
+
+/* DRAM address to which u-boot proper is loaded (before it relocates itself) */
+#define CONFIG_SYS_NAND_U_BOOT_DST  0xa0000000
+#define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_NAND_U_BOOT_DST
+
+/* passed to linker by Makefile as arg to -Ttext option */
+#define CONFIG_SYS_TEXT_BASE 0xa0000000
+
+#define CONFIG_SYS_INIT_SP_ADDR         0x5c040000 /* end of internal SRAM */
+
+/*
+ * environment
+ */
+#define CONFIG_ENV_IS_NOWHERE
+#define CONFIG_BUILD_ENVCRC
+#define CONFIG_ENV_SIZE 0x200
+#define CONFIG_SYS_CONSOLE_IS_IN_ENV
+#define CONFIG_EXTRA_ENV_SETTINGS  \
+	"stdin=usbtty\0"           \
+	"stdout=usbtty\0"          \
+	"stderr=usbtty"
+#define CONFIG_BOOTARGS "mtdparts=Msys_Diskonchip_G4:1536k(protected_part)ro,1024k(bootloader_part),-(filesys_part) \
+ip=192.168.11.102:::255.255.255.0:treo:usb0"
+#define CONFIG_BOOTDELAY   3
+
+#if 0 /* example: try 2nd mmc partition, then nand */
+#define CONFIG_BOOTCOMMAND                                              \
+	"mmc rescan; "                                                  \
+	"if mmcinfo && ext2load mmc 0:2 0xa1000000 uImage; then "       \
+	    "bootm 0xa1000000; "					\
+	"elif nand read 0xa1000000 0x280000 0x240000; then "            \
+	    "bootm 0xa1000000; "					\
+	"fi; "
+#endif
+
+/* u-boot lives at end of SDRAM, so use start of SDRAM for stand alone apps */
+#define CONFIG_STANDALONE_LOAD_ADDR 0xa0000000
+
+#define CONFIG_SYS_DCACHE_OFF
+#define CONFIG_SYS_ICACHE_OFF
+
+#endif  /* __CONFIG_H */