keymile: Make distinct kmtegr1, kmvect1, suvd3 configs
The kmtegr1, kmvect1, and suvd3 boards all use the same config include
file with lots of #ifdefs in it.
The Kconfig migation will become easier if we get rid of these #ifdefs
first.
Hence, create distinct config include files for these boards, and unwind
the #ifdef logic in these config files to only include the options
necessary for each board.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
diff --git a/include/configs/kmvect1.h b/include/configs/kmvect1.h
new file mode 100644
index 0000000..178e769
--- /dev/null
+++ b/include/configs/kmvect1.h
@@ -0,0 +1,133 @@
+/* SPDX-License-Identifier: GPL-2.0+ */
+/*
+ * Copyright (C) 2006 Freescale Semiconductor, Inc.
+ * Dave Liu <daveliu@freescale.com>
+ *
+ * Copyright (C) 2007 Logic Product Development, Inc.
+ * Peter Barada <peterb@logicpd.com>
+ *
+ * Copyright (C) 2007 MontaVista Software, Inc.
+ * Anton Vorontsov <avorontsov@ru.mvista.com>
+ *
+ * (C) Copyright 2010
+ * Heiko Schocher, DENX Software Engineering, hs@denx.de.
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/*
+ * High Level Configuration Options
+ */
+
+/* This needs to be set prior to including km/km83xx-common.h */
+
+#define CONFIG_HOSTNAME "kmvect1"
+#define CONFIG_KM_BOARD_NAME "kmvect1"
+/* at end of uboot partition, before env */
+#define CONFIG_SYS_QE_FW_ADDR 0xF00B0000
+/* include common defines/options for all 8309 Keymile boards */
+#include "km/km8309-common.h"
+
+#define CONFIG_SYS_APP1_BASE 0xA0000000
+#define CONFIG_SYS_APP1_SIZE 256 /* Megabytes */
+#define CONFIG_SYS_APP2_BASE 0xB0000000
+#define CONFIG_SYS_APP2_SIZE 256 /* Megabytes */
+
+/* EEprom support */
+#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
+
+/*
+ * Init Local Bus Memory Controller:
+ *
+ * Bank Bus Machine PortSz Size Device
+ * ---- --- ------- ------ ----- ------
+ * 2 Local UPMA 16 bit 256MB APP1
+ * 3 Local GPCM 16 bit 256MB APP2
+ *
+ */
+
+/*
+ * APP1 on the local bus CS2
+ */
+#define CONFIG_SYS_LBLAWBAR2_PRELIM CONFIG_SYS_APP1_BASE
+#define CONFIG_SYS_LBLAWAR2_PRELIM (LBLAWAR_EN | LBLAWAR_256MB)
+
+#define CONFIG_SYS_BR2_PRELIM (CONFIG_SYS_APP1_BASE | \
+ BR_PS_16 | \
+ BR_MS_UPMA | \
+ BR_V)
+#define CONFIG_SYS_OR2_PRELIM (MEG_TO_AM(CONFIG_SYS_APP1_SIZE))
+
+#define CONFIG_SYS_BR3_PRELIM (CONFIG_SYS_APP2_BASE | \
+ BR_PS_16 | \
+ BR_V)
+
+#define CONFIG_SYS_OR3_PRELIM (MEG_TO_AM(CONFIG_SYS_APP2_SIZE) | \
+ OR_GPCM_CSNT | \
+ OR_GPCM_ACS_DIV4 | \
+ OR_GPCM_SCY_3 | \
+ OR_GPCM_TRLX_SET)
+
+#define CONFIG_SYS_MAMR (MxMR_GPL_x4DIS | \
+ 0x0000c000 | \
+ MxMR_WLFx_2X)
+
+#define CONFIG_SYS_LBLAWBAR3_PRELIM CONFIG_SYS_APP2_BASE
+#define CONFIG_SYS_LBLAWAR3_PRELIM (LBLAWAR_EN | LBLAWAR_256MB)
+
+/*
+ * MMU Setup
+ */
+/* APP1: icache cacheable, but dcache-inhibit and guarded */
+#define CONFIG_SYS_IBAT5L (CONFIG_SYS_APP1_BASE | BATL_PP_RW | \
+ BATL_MEMCOHERENCE)
+#define CONFIG_SYS_IBAT5U (CONFIG_SYS_APP1_BASE | BATU_BL_256M | \
+ BATU_VS | BATU_VP)
+#define CONFIG_SYS_DBAT5L (CONFIG_SYS_APP1_BASE | BATL_PP_RW | \
+ BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
+#define CONFIG_SYS_DBAT5U CONFIG_SYS_IBAT5U
+#define CONFIG_SYS_IBAT6L (CONFIG_SYS_APP2_BASE | BATL_PP_RW | \
+ BATL_MEMCOHERENCE)
+#define CONFIG_SYS_IBAT6U (CONFIG_SYS_APP2_BASE | BATU_BL_256M | \
+ BATU_VS | BATU_VP)
+#define CONFIG_SYS_DBAT6L (CONFIG_SYS_APP2_BASE | BATL_PP_RW | \
+ BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
+#define CONFIG_SYS_DBAT6U CONFIG_SYS_IBAT6U
+
+/*
+ * QE UEC ethernet configuration
+ */
+#define CONFIG_MV88E6352_SWITCH
+#define CONFIG_KM_MVEXTSW_ADDR 0x10
+
+/* ethernet port connected to simple switch 88e6122 (UEC0) */
+#define CONFIG_UEC_ETH1
+#define CONFIG_SYS_UEC1_UCC_NUM 0 /* UCC1 */
+#define CONFIG_SYS_UEC1_RX_CLK QE_CLK9
+#define CONFIG_SYS_UEC1_TX_CLK QE_CLK10
+
+#define CONFIG_FIXED_PHY 0xFFFFFFFF
+#define CONFIG_SYS_FIXED_PHY_ADDR 0x1E /* unused address */
+#define CONFIG_SYS_FIXED_PHY_PORT(devnum, speed, duplex) \
+ {devnum, speed, duplex}
+#define CONFIG_SYS_FIXED_PHY_PORTS \
+ CONFIG_SYS_FIXED_PHY_PORT("UEC0", SPEED_100, DUPLEX_FULL)
+
+#define CONFIG_SYS_UEC1_ETH_TYPE FAST_ETH
+#define CONFIG_SYS_UEC1_PHY_ADDR CONFIG_SYS_FIXED_PHY_ADDR
+#define CONFIG_SYS_UEC1_INTERFACE_TYPE PHY_INTERFACE_MODE_MII
+#define CONFIG_SYS_UEC1_INTERFACE_SPEED 100
+
+/* ethernet port connected to piggy (UEC2) */
+#define CONFIG_HAS_ETH1
+#define CONFIG_UEC_ETH2
+#define CONFIG_SYS_UEC2_UCC_NUM 2 /* UCC3 */
+#define CONFIG_SYS_UEC2_RX_CLK QE_CLK_NONE /* not used in RMII Mode */
+#define CONFIG_SYS_UEC2_TX_CLK QE_CLK12
+#define CONFIG_SYS_UEC2_ETH_TYPE FAST_ETH
+#define CONFIG_SYS_UEC2_PHY_ADDR 0
+#define CONFIG_SYS_UEC2_INTERFACE_TYPE PHY_INTERFACE_MODE_RMII
+#define CONFIG_SYS_UEC2_INTERFACE_SPEED 100
+
+#endif /* __CONFIG_H */