ls102xa: etsec: Select ge0_clk125 for eTSEC clock muxing as default
This patch reverts to use ge0_clk125 for eTSEC clock muxing. For SAI and
CAN which are pin multiplexed with RGMII1 in EC1 of RCW, ge2_clk125 will
be used via hwconfig.
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@freescale.com>
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
diff --git a/board/freescale/ls1021aqds/ls1021aqds.c b/board/freescale/ls1021aqds/ls1021aqds.c
index 152da2d..0a3252e 100644
--- a/board/freescale/ls1021aqds/ls1021aqds.c
+++ b/board/freescale/ls1021aqds/ls1021aqds.c
@@ -48,6 +48,12 @@
MUX_TYPE_SD_PC_SG_SG,
};
+enum {
+ GE0_CLK125,
+ GE2_CLK125,
+ GE1_CLK125,
+};
+
int checkboard(void)
{
#ifndef CONFIG_QSPI_BOOT
@@ -177,7 +183,6 @@
#ifdef CONFIG_TSEC_ENET
out_be32(&scfg->etsecdmamcr, SCFG_ETSECDMAMCR_LE_BD_FR);
- out_be32(&scfg->etsecmcr, SCFG_ETSECCMCR_GE2_CLK125);
#endif
#ifdef CONFIG_FSL_IFC
@@ -241,6 +246,32 @@
}
#endif
+void config_etseccm_source(int etsec_gtx_125_mux)
+{
+ struct ccsr_scfg *scfg = (struct ccsr_scfg *)CONFIG_SYS_FSL_SCFG_ADDR;
+
+ switch (etsec_gtx_125_mux) {
+ case GE0_CLK125:
+ out_be32(&scfg->etsecmcr, SCFG_ETSECCMCR_GE0_CLK125);
+ debug("etseccm set to GE0_CLK125\n");
+ break;
+
+ case GE2_CLK125:
+ out_be32(&scfg->etsecmcr, SCFG_ETSECCMCR_GE2_CLK125);
+ debug("etseccm set to GE2_CLK125\n");
+ break;
+
+ case GE1_CLK125:
+ out_be32(&scfg->etsecmcr, SCFG_ETSECCMCR_GE1_CLK125);
+ debug("etseccm set to GE1_CLK125\n");
+ break;
+
+ default:
+ printf("Error! trying to set etseccm to invalid value\n");
+ break;
+ }
+}
+
int config_board_mux(int ctrl_type)
{
u8 reg12, reg14;
@@ -250,6 +281,7 @@
switch (ctrl_type) {
case MUX_TYPE_CAN:
+ config_etseccm_source(GE2_CLK125);
reg14 = SET_EC_MUX_SEL(reg14, PIN_MUX_SEL_CAN);
break;
case MUX_TYPE_IIC2:
@@ -259,6 +291,7 @@
reg14 = SET_EC_MUX_SEL(reg14, PIN_MUX_SEL_RGMII);
break;
case MUX_TYPE_SAI:
+ config_etseccm_source(GE2_CLK125);
reg14 = SET_EC_MUX_SEL(reg14, PIN_MUX_SEL_SAI);
break;
case MUX_TYPE_SDHC: