arm64: zynqmp: Add support for zc1751 dc3
zc1751 is based board with dc3 extenstion card which is used for silicon
validation.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
diff --git a/arch/arm/dts/zynqmp-zc1751-xm017-dc3.dts b/arch/arm/dts/zynqmp-zc1751-xm017-dc3.dts
new file mode 100644
index 0000000..d6a0103
--- /dev/null
+++ b/arch/arm/dts/zynqmp-zc1751-xm017-dc3.dts
@@ -0,0 +1,210 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * dts file for Xilinx ZynqMP zc1751-xm017-dc3
+ *
+ * (C) Copyright 2016 - 2018, Xilinx, Inc.
+ *
+ * Michal Simek <michal.simek@xilinx.com>
+ */
+
+/dts-v1/;
+
+#include "zynqmp.dtsi"
+#include "zynqmp-clk-ccf.dtsi"
+
+/ {
+ model = "ZynqMP zc1751-xm017-dc3 RevA";
+ compatible = "xlnx,zynqmp-zc1751", "xlnx,zynqmp";
+
+ aliases {
+ ethernet0 = &gem0;
+ gpio0 = &gpio;
+ i2c0 = &i2c0;
+ i2c1 = &i2c1;
+ mmc0 = &sdhci1;
+ rtc0 = &rtc;
+ serial0 = &uart0;
+ serial1 = &uart1;
+ usb0 = &usb0;
+ usb1 = &usb1;
+ };
+
+ chosen {
+ bootargs = "earlycon";
+ stdout-path = "serial0:115200n8";
+ };
+
+ memory@0 {
+ device_type = "memory";
+ reg = <0x0 0x0 0x0 0x80000000>, <0x8 0x00000000 0x0 0x80000000>;
+ };
+};
+
+&fpd_dma_chan1 {
+ status = "okay";
+};
+
+&fpd_dma_chan2 {
+ status = "okay";
+};
+
+&fpd_dma_chan3 {
+ status = "okay";
+};
+
+&fpd_dma_chan4 {
+ status = "okay";
+};
+
+&fpd_dma_chan5 {
+ status = "okay";
+};
+
+&fpd_dma_chan6 {
+ status = "okay";
+};
+
+&fpd_dma_chan7 {
+ status = "okay";
+};
+
+&fpd_dma_chan8 {
+ status = "okay";
+};
+
+&gem0 {
+ status = "okay";
+ phy-handle = <&phy0>;
+ phy-mode = "rgmii-id";
+ phy0: phy@0 { /* VSC8211 */
+ reg = <0>;
+ };
+};
+
+&gpio {
+ status = "okay";
+};
+
+/* just eeprom here */
+&i2c0 {
+ status = "okay";
+ clock-frequency = <400000>;
+
+ tca6416_u26: gpio@20 {
+ compatible = "ti,tca6416";
+ reg = <0x20>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ /* IRQ not connected */
+ };
+
+ rtc@68 {
+ compatible = "dallas,ds1339";
+ reg = <0x68>;
+ };
+};
+
+/* eeprom24c02 and SE98A temp chip pca9306 */
+&i2c1 {
+ status = "okay";
+ clock-frequency = <400000>;
+};
+
+/* MT29F64G08AECDBJ4-6 */
+&nand0 {
+ status = "okay";
+ arasan,has-mdma;
+ num-cs = <2>;
+
+ partition@0 { /* for testing purpose */
+ label = "nand-fsbl-uboot";
+ reg = <0x0 0x0 0x400000>;
+ };
+ partition@1 { /* for testing purpose */
+ label = "nand-linux";
+ reg = <0x0 0x400000 0x1400000>;
+ };
+ partition@2 { /* for testing purpose */
+ label = "nand-device-tree";
+ reg = <0x0 0x1800000 0x400000>;
+ };
+ partition@3 { /* for testing purpose */
+ label = "nand-rootfs";
+ reg = <0x0 0x1C00000 0x1400000>;
+ };
+ partition@4 { /* for testing purpose */
+ label = "nand-bitstream";
+ reg = <0x0 0x3000000 0x400000>;
+ };
+ partition@5 { /* for testing purpose */
+ label = "nand-misc";
+ reg = <0x0 0x3400000 0xFCC00000>;
+ };
+
+ partition@6 { /* for testing purpose */
+ label = "nand1-fsbl-uboot";
+ reg = <0x1 0x0 0x400000>;
+ };
+ partition@7 { /* for testing purpose */
+ label = "nand1-linux";
+ reg = <0x1 0x400000 0x1400000>;
+ };
+ partition@8 { /* for testing purpose */
+ label = "nand1-device-tree";
+ reg = <0x1 0x1800000 0x400000>;
+ };
+ partition@9 { /* for testing purpose */
+ label = "nand1-rootfs";
+ reg = <0x1 0x1C00000 0x1400000>;
+ };
+ partition@10 { /* for testing purpose */
+ label = "nand1-bitstream";
+ reg = <0x1 0x3000000 0x400000>;
+ };
+ partition@11 { /* for testing purpose */
+ label = "nand1-misc";
+ reg = <0x1 0x3400000 0xFCC00000>;
+ };
+};
+
+&rtc {
+ status = "okay";
+};
+
+&sata {
+ status = "okay";
+ /* SATA phy OOB timing settings */
+ ceva,p0-cominit-params = /bits/ 8 <0x1B 0x4D 0x18 0x28>;
+ ceva,p0-comwake-params = /bits/ 8 <0x06 0x19 0x08 0x0E>;
+ ceva,p0-burst-params = /bits/ 8 <0x13 0x08 0x4A 0x06>;
+ ceva,p0-retry-params = /bits/ 16 <0x96A4 0x3FFC>;
+ ceva,p1-cominit-params = /bits/ 8 <0x1B 0x4D 0x18 0x28>;
+ ceva,p1-comwake-params = /bits/ 8 <0x06 0x19 0x08 0x0E>;
+ ceva,p1-burst-params = /bits/ 8 <0x13 0x08 0x4A 0x06>;
+ ceva,p1-retry-params = /bits/ 16 <0x96A4 0x3FFC>;
+};
+
+&sdhci1 { /* emmc with some settings */
+ status = "okay";
+};
+
+/* main */
+&uart0 {
+ status = "okay";
+};
+
+/* DB9 */
+&uart1 {
+ status = "okay";
+};
+
+&usb0 {
+ status = "okay";
+ dr_mode = "host";
+};
+
+/* ULPI SMSC USB3320 */
+&usb1 {
+ status = "okay";
+ dr_mode = "host";
+};