Merge branch 'master' of /home/wd/git/u-boot/custodians
diff --git a/Makefile b/Makefile
index 3e7cffc..852dca8 100644
--- a/Makefile
+++ b/Makefile
@@ -2462,20 +2462,8 @@
versatilepb_config : unconfig
@board/versatile/split_by_variant.sh $@
-voiceblue_smallflash_config \
voiceblue_config: unconfig
- @mkdir -p $(obj)include
- @mkdir -p $(obj)board/voiceblue
- @if [ "$(findstring _smallflash_,$@)" ] ; then \
- $(XECHO) "... boot from lower flash bank" ; \
- echo "#define VOICEBLUE_SMALL_FLASH" >>$(obj)include/config.h ; \
- echo "VOICEBLUE_SMALL_FLASH=y" >$(obj)board/voiceblue/config.tmp ; \
- else \
- $(XECHO) "... boot from upper flash bank" ; \
- >$(obj)include/config.h ; \
- echo "VOICEBLUE_SMALL_FLASH=n" >$(obj)board/voiceblue/config.tmp ; \
- fi
- @$(MKCONFIG) -a voiceblue arm arm925t voiceblue
+ @$(MKCONFIG) $(@:_config=) arm arm925t voiceblue
cm4008_config : unconfig
@$(MKCONFIG) $(@:_config=) arm arm920t cm4008 NULL ks8695
diff --git a/board/ads5121/ads5121.c b/board/ads5121/ads5121.c
index 1582c22..462f41d 100644
--- a/board/ads5121/ads5121.c
+++ b/board/ads5121/ads5121.c
@@ -126,24 +126,24 @@
im->mddrc.prioman_config2 = CFG_MDDRCGRP_PM_CFG2;
im->mddrc.hiprio_config = CFG_MDDRCGRP_HIPRIO_CFG;
im->mddrc.lut_table0_main_upper = CFG_MDDRCGRP_LUT0_MU;
- im->mddrc.lut_table1_main_upper = CFG_MDDRCGRP_LUT1_MU;
- im->mddrc.lut_table2_main_upper = CFG_MDDRCGRP_LUT2_MU;
- im->mddrc.lut_table3_main_upper = CFG_MDDRCGRP_LUT3_MU;
- im->mddrc.lut_table4_main_upper = CFG_MDDRCGRP_LUT4_MU;
im->mddrc.lut_table0_main_lower = CFG_MDDRCGRP_LUT0_ML;
+ im->mddrc.lut_table1_main_upper = CFG_MDDRCGRP_LUT1_MU;
im->mddrc.lut_table1_main_lower = CFG_MDDRCGRP_LUT1_ML;
+ im->mddrc.lut_table2_main_upper = CFG_MDDRCGRP_LUT2_MU;
im->mddrc.lut_table2_main_lower = CFG_MDDRCGRP_LUT2_ML;
+ im->mddrc.lut_table3_main_upper = CFG_MDDRCGRP_LUT3_MU;
im->mddrc.lut_table3_main_lower = CFG_MDDRCGRP_LUT3_ML;
+ im->mddrc.lut_table4_main_upper = CFG_MDDRCGRP_LUT4_MU;
im->mddrc.lut_table4_main_lower = CFG_MDDRCGRP_LUT4_ML;
im->mddrc.lut_table0_alternate_upper = CFG_MDDRCGRP_LUT0_AU;
- im->mddrc.lut_table1_alternate_upper = CFG_MDDRCGRP_LUT1_AU;
- im->mddrc.lut_table2_alternate_upper = CFG_MDDRCGRP_LUT2_AU;
- im->mddrc.lut_table3_alternate_upper = CFG_MDDRCGRP_LUT3_AU;
- im->mddrc.lut_table4_alternate_upper = CFG_MDDRCGRP_LUT4_AU;
im->mddrc.lut_table0_alternate_lower = CFG_MDDRCGRP_LUT0_AL;
+ im->mddrc.lut_table1_alternate_upper = CFG_MDDRCGRP_LUT1_AU;
im->mddrc.lut_table1_alternate_lower = CFG_MDDRCGRP_LUT1_AL;
+ im->mddrc.lut_table2_alternate_upper = CFG_MDDRCGRP_LUT2_AU;
im->mddrc.lut_table2_alternate_lower = CFG_MDDRCGRP_LUT2_AL;
+ im->mddrc.lut_table3_alternate_upper = CFG_MDDRCGRP_LUT3_AU;
im->mddrc.lut_table3_alternate_lower = CFG_MDDRCGRP_LUT3_AL;
+ im->mddrc.lut_table4_alternate_upper = CFG_MDDRCGRP_LUT4_AU;
im->mddrc.lut_table4_alternate_lower = CFG_MDDRCGRP_LUT4_AL;
/* Initialize MDDRC */
@@ -157,18 +157,26 @@
im->mddrc.ddr_command = CFG_MICRON_NOP;
im->mddrc.ddr_command = CFG_MICRON_PCHG_ALL;
+ im->mddrc.ddr_command = CFG_MICRON_NOP;
+ im->mddrc.ddr_command = CFG_MICRON_RFSH;
+ im->mddrc.ddr_command = CFG_MICRON_NOP;
+ im->mddrc.ddr_command = CFG_MICRON_RFSH;
+ im->mddrc.ddr_command = CFG_MICRON_NOP;
+ im->mddrc.ddr_command = CFG_MICRON_INIT_DEV_OP;
+ im->mddrc.ddr_command = CFG_MICRON_NOP;
+ im->mddrc.ddr_command = CFG_MICRON_EM2;
+ im->mddrc.ddr_command = CFG_MICRON_NOP;
+ im->mddrc.ddr_command = CFG_MICRON_PCHG_ALL;
im->mddrc.ddr_command = CFG_MICRON_EM2;
im->mddrc.ddr_command = CFG_MICRON_EM3;
im->mddrc.ddr_command = CFG_MICRON_EN_DLL;
- im->mddrc.ddr_command = CFG_MICRON_RST_DLL;
+ im->mddrc.ddr_command = CFG_MICRON_INIT_DEV_OP;
im->mddrc.ddr_command = CFG_MICRON_PCHG_ALL;
im->mddrc.ddr_command = CFG_MICRON_RFSH;
im->mddrc.ddr_command = CFG_MICRON_INIT_DEV_OP;
im->mddrc.ddr_command = CFG_MICRON_OCD_DEFAULT;
- im->mddrc.ddr_command = CFG_MICRON_OCD_EXIT;
-
- for (i = 0; i < 10; i++)
- im->mddrc.ddr_command = CFG_MICRON_NOP;
+ im->mddrc.ddr_command = CFG_MICRON_PCHG_ALL;
+ im->mddrc.ddr_command = CFG_MICRON_NOP;
/* Start MDDRC */
im->mddrc.ddr_time_config0 = CFG_MDDRC_TIME_CFG0_RUN;
diff --git a/board/voiceblue/Makefile b/board/voiceblue/Makefile
index 5f340b4..9386bb0 100644
--- a/board/voiceblue/Makefile
+++ b/board/voiceblue/Makefile
@@ -62,7 +62,7 @@
distclean: clean
- rm -f $(LIB) core config.tmp *.bak .depend
+ rm -f $(LIB) core *.bak .depend
#########################################################################
diff --git a/board/voiceblue/config.mk b/board/voiceblue/config.mk
index d55daa4..2cfc56a 100644
--- a/board/voiceblue/config.mk
+++ b/board/voiceblue/config.mk
@@ -1,16 +1 @@
-#
-# Linux-Kernel is expected to be at 1000'8000,
-# entry 1000'8000 (mem base + reserved)
-#
-
-sinclude $(OBJTREE)/board/$(BOARDDIR)/config.tmp
-
-ifeq ($(VOICEBLUE_SMALL_FLASH),y)
-# We load ourself to internal SRAM at 2001'2000
-# Check map file when changing TEXT_BASE.
-# Everything has fit into 192kB internal SRAM!
-TEXT_BASE = 0x20012000
-else
-# Running in SDRAM...
TEXT_BASE = 0x13FD0000
-endif
diff --git a/board/voiceblue/setup.S b/board/voiceblue/setup.S
index dcf37b5..78cd2b6 100644
--- a/board/voiceblue/setup.S
+++ b/board/voiceblue/setup.S
@@ -77,7 +77,7 @@
.word 0x00000000 @ FUNC_MUX_CTRL_3
.word 0x00000000 @ FUNC_MUX_CTRL_4
.word 0x12082480 @ FUNC_MUX_CTRL_5
- .word 0x00000004 @ FUNC_MUX_CTRL_6
+ .word 0x0000001c @ FUNC_MUX_CTRL_6
.word 0x00000003 @ FUNC_MUX_CTRL_7
.word 0x10001200 @ FUNC_MUX_CTRL_8
.word 0x01201012 @ FUNC_MUX_CTRL_9
diff --git a/board/xsengine/xsengine.c b/board/xsengine/xsengine.c
index 23d56c4..65923e9 100644
--- a/board/xsengine/xsengine.c
+++ b/board/xsengine/xsengine.c
@@ -47,7 +47,7 @@
return 0;
}
-int board_post_init (void)
+int board_late_init (void)
{
setenv ("stdout", "serial");
setenv ("stderr", "serial");
diff --git a/common/cmd_bdinfo.c b/common/cmd_bdinfo.c
index c28a155..4e77461 100644
--- a/common/cmd_bdinfo.c
+++ b/common/cmd_bdinfo.c
@@ -316,6 +316,7 @@
print_num("-> size", bd->bi_dram[i].size);
}
+#if defined(CONFIG_CMD_NET)
puts ("ethaddr =");
for (i=0; i<6; ++i) {
printf ("%c%02X", i ? ':' : ' ', bd->bi_enetaddr[i]);
@@ -323,6 +324,7 @@
puts ( "\n"
"ip_addr = ");
print_IPaddr (bd->bi_ip_addr);
+#endif
printf ("\n"
"baudrate = %d bps\n", bd->bi_baudrate);
diff --git a/common/cmd_net.c b/common/cmd_net.c
index 56eb684..dbf6b86 100644
--- a/common/cmd_net.c
+++ b/common/cmd_net.c
@@ -51,7 +51,7 @@
U_BOOT_CMD(
tftpboot, 3, 1, do_tftpb,
"tftpboot- boot image via network using TFTP protocol\n",
- "[loadAddress] [bootfilename]\n"
+ "[loadAddress] [[hostIPaddr:]bootfilename]\n"
);
int do_rarpb (cmd_tbl_t *cmdtp, int flag, int argc, char *argv[])
diff --git a/common/fdt_support.c b/common/fdt_support.c
index a13c140..92f1c7f 100644
--- a/common/fdt_support.c
+++ b/common/fdt_support.c
@@ -30,9 +30,6 @@
#include <fdt_support.h>
#include <exports.h>
-#ifdef CONFIG_QE
-#include "../drivers/qe/qe.h"
-#endif
/*
* Global data (for the gd->bd)
*/
@@ -617,49 +614,4 @@
#endif
}
}
-
-#ifdef CONFIG_QE
-/*
- * If a QE firmware has been uploaded, then add the 'firmware' node under
- * the 'qe' node.
- */
-void fdt_fixup_qe_firmware(void *fdt)
-{
- struct qe_firmware_info *qe_fw_info;
- int node, ret;
-
- qe_fw_info = qe_get_firmware_info();
- if (!qe_fw_info)
- return;
-
- node = fdt_path_offset(fdt, "/qe");
- if (node < 0)
- return;
-
- /* We assume the node doesn't exist yet */
- node = fdt_add_subnode(fdt, node, "firmware");
- if (node < 0)
- return;
-
- ret = fdt_setprop(fdt, node, "extended-modes",
- &qe_fw_info->extended_modes, sizeof(u64));
- if (ret < 0)
- goto error;
-
- ret = fdt_setprop_string(fdt, node, "id", qe_fw_info->id);
- if (ret < 0)
- goto error;
-
- ret = fdt_setprop(fdt, node, "virtual-traps", qe_fw_info->vtraps,
- sizeof(qe_fw_info->vtraps));
- if (ret < 0)
- goto error;
-
- return;
-
-error:
- fdt_del_node(fdt, node);
-}
-#endif
-
#endif
diff --git a/common/serial.c b/common/serial.c
index 5601080..bfda7ca 100644
--- a/common/serial.c
+++ b/common/serial.c
@@ -60,6 +60,16 @@
#else
return &serial0_device;
#endif
+#elif defined(CONFIG_S3C2410)
+#if defined(CONFIG_SERIAL1)
+ return &s3c24xx_serial0_device;
+#elif defined(CONFIG_SERIAL2)
+ return &s3c24xx_serial1_device;
+#elif defined(CONFIG_SERIAL3)
+ return &s3c24xx_serial2_device;
+#else
+#error "CONFIG_SERIAL? missing."
+#endif
#else
#error No default console
#endif
@@ -123,6 +133,11 @@
#if defined (CONFIG_STUART)
serial_register(&serial_stuart_device);
#endif
+#if defined(CONFIG_S3C2410)
+ serial_register(&s3c24xx_serial0_device);
+ serial_register(&s3c24xx_serial1_device);
+ serial_register(&s3c24xx_serial2_device);
+#endif
serial_assign (default_serial_console ()->name);
}
diff --git a/cpu/arm920t/interrupts.c b/cpu/arm920t/interrupts.c
index a43a3ed..0a6d94f 100644
--- a/cpu/arm920t/interrupts.c
+++ b/cpu/arm920t/interrupts.c
@@ -161,11 +161,16 @@
void do_irq (struct pt_regs *pt_regs)
{
-#if defined (CONFIG_USE_IRQ) && defined (CONFIG_ARCH_INTEGRATOR)
+#if defined (CONFIG_USE_IRQ)
+#if defined (ARM920_IRQ_CALLBACK)
+ ARM920_IRQ_CALLBACK();
+ return;
+#elif defined (CONFIG_ARCH_INTEGRATOR)
/* ASSUMED to be a timer interrupt */
/* Just clear it - count handled in */
/* integratorap.c */
*(volatile ulong *)(CFG_TIMERBASE + 0x0C) = 0;
+#endif /* ARCH_INTEGRATOR */
#else
printf ("interrupt request\n");
show_regs (pt_regs);
diff --git a/cpu/arm920t/s3c24x0/Makefile b/cpu/arm920t/s3c24x0/Makefile
index 1ed9bf3..6764920 100644
--- a/cpu/arm920t/s3c24x0/Makefile
+++ b/cpu/arm920t/s3c24x0/Makefile
@@ -26,7 +26,7 @@
LIB = $(obj)lib$(SOC).a
COBJS = i2c.o interrupts.o serial.o speed.o \
- usb.o usb_ohci.o
+ usb.o usb_ohci.o nand.o
SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c)
OBJS := $(addprefix $(obj),$(SOBJS) $(COBJS))
diff --git a/cpu/arm920t/s3c24x0/interrupts.c b/cpu/arm920t/s3c24x0/interrupts.c
index 1b36412..7ad9fcb 100644
--- a/cpu/arm920t/s3c24x0/interrupts.c
+++ b/cpu/arm920t/s3c24x0/interrupts.c
@@ -216,4 +216,13 @@
/*NOTREACHED*/
}
+#ifdef CONFIG_USE_IRQ
+void s3c2410_irq(void)
+{
+ S3C24X0_INTERRUPT * irq = S3C24X0_GetBase_INTERRUPT();
+ u_int32_t intpnd = irq->INTPND;
+
+}
+#endif /* USE_IRQ */
+
#endif /* defined(CONFIG_S3C2400) || defined (CONFIG_S3C2410) || defined (CONFIG_TRAB) */
diff --git a/cpu/arm920t/s3c24x0/nand.c b/cpu/arm920t/s3c24x0/nand.c
new file mode 100644
index 0000000..e1bf128
--- /dev/null
+++ b/cpu/arm920t/s3c24x0/nand.c
@@ -0,0 +1,179 @@
+/*
+ * (C) Copyright 2006 OpenMoko, Inc.
+ * Author: Harald Welte <laforge@openmoko.org>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+
+#if 0
+#define DEBUGN printf
+#else
+#define DEBUGN(x, args ...) {}
+#endif
+
+#if defined(CONFIG_CMD_NAND)
+#if !defined(CFG_NAND_LEGACY)
+
+#include <nand.h>
+#include <s3c2410.h>
+
+#define __REGb(x) (*(volatile unsigned char *)(x))
+#define __REGi(x) (*(volatile unsigned int *)(x))
+
+#define NF_BASE 0x4e000000
+#define NFCONF __REGi(NF_BASE + 0x0)
+#define NFCMD __REGb(NF_BASE + 0x4)
+#define NFADDR __REGb(NF_BASE + 0x8)
+#define NFDATA __REGb(NF_BASE + 0xc)
+#define NFSTAT __REGb(NF_BASE + 0x10)
+#define NFECC0 __REGb(NF_BASE + 0x14)
+#define NFECC1 __REGb(NF_BASE + 0x15)
+#define NFECC2 __REGb(NF_BASE + 0x16)
+
+#define S3C2410_NFCONF_EN (1<<15)
+#define S3C2410_NFCONF_512BYTE (1<<14)
+#define S3C2410_NFCONF_4STEP (1<<13)
+#define S3C2410_NFCONF_INITECC (1<<12)
+#define S3C2410_NFCONF_nFCE (1<<11)
+#define S3C2410_NFCONF_TACLS(x) ((x)<<8)
+#define S3C2410_NFCONF_TWRPH0(x) ((x)<<4)
+#define S3C2410_NFCONF_TWRPH1(x) ((x)<<0)
+
+static void s3c2410_hwcontrol(struct mtd_info *mtd, int cmd)
+{
+ struct nand_chip *chip = mtd->priv;
+
+ DEBUGN("hwcontrol(): 0x%02x: ", cmd);
+
+ switch (cmd) {
+ case NAND_CTL_SETNCE:
+ NFCONF &= ~S3C2410_NFCONF_nFCE;
+ DEBUGN("NFCONF=0x%08x\n", NFCONF);
+ break;
+ case NAND_CTL_CLRNCE:
+ NFCONF |= S3C2410_NFCONF_nFCE;
+ DEBUGN("NFCONF=0x%08x\n", NFCONF);
+ break;
+ case NAND_CTL_SETALE:
+ chip->IO_ADDR_W = NF_BASE + 0x8;
+ DEBUGN("SETALE\n");
+ break;
+ case NAND_CTL_SETCLE:
+ chip->IO_ADDR_W = NF_BASE + 0x4;
+ DEBUGN("SETCLE\n");
+ break;
+ default:
+ chip->IO_ADDR_W = NF_BASE + 0xc;
+ break;
+ }
+ return;
+}
+
+static int s3c2410_dev_ready(struct mtd_info *mtd)
+{
+ DEBUGN("dev_ready\n");
+ return (NFSTAT & 0x01);
+}
+
+#ifdef CONFIG_S3C2410_NAND_HWECC
+void s3c2410_nand_enable_hwecc(struct mtd_info *mtd, int mode)
+{
+ DEBUGN("s3c2410_nand_enable_hwecc(%p, %d)\n", mtd ,mode);
+ NFCONF |= S3C2410_NFCONF_INITECC;
+}
+
+static int s3c2410_nand_calculate_ecc(struct mtd_info *mtd, const u_char *dat,
+ u_char *ecc_code)
+{
+ ecc_code[0] = NFECC0;
+ ecc_code[1] = NFECC1;
+ ecc_code[2] = NFECC2;
+ DEBUGN("s3c2410_nand_calculate_hwecc(%p,): 0x%02x 0x%02x 0x%02x\n",
+ mtd , ecc_code[0], ecc_code[1], ecc_code[2]);
+
+ return 0;
+}
+
+static int s3c2410_nand_correct_data(struct mtd_info *mtd, u_char *dat,
+ u_char *read_ecc, u_char *calc_ecc)
+{
+ if (read_ecc[0] == calc_ecc[0] &&
+ read_ecc[1] == calc_ecc[1] &&
+ read_ecc[2] == calc_ecc[2])
+ return 0;
+
+ printf("s3c2410_nand_correct_data: not implemented\n");
+ return -1;
+}
+#endif
+
+int board_nand_init(struct nand_chip *nand)
+{
+ u_int32_t cfg;
+ u_int8_t tacls, twrph0, twrph1;
+ S3C24X0_CLOCK_POWER * const clk_power = S3C24X0_GetBase_CLOCK_POWER();
+
+ DEBUGN("board_nand_init()\n");
+
+ clk_power->CLKCON |= (1 << 4);
+
+ /* initialize hardware */
+ twrph0 = 3; twrph1 = 0; tacls = 0;
+
+ cfg = S3C2410_NFCONF_EN;
+ cfg |= S3C2410_NFCONF_TACLS(tacls - 1);
+ cfg |= S3C2410_NFCONF_TWRPH0(twrph0 - 1);
+ cfg |= S3C2410_NFCONF_TWRPH1(twrph1 - 1);
+
+ NFCONF = cfg;
+
+ /* initialize nand_chip data structure */
+ nand->IO_ADDR_R = nand->IO_ADDR_W = 0x4e00000c;
+
+ /* read_buf and write_buf are default */
+ /* read_byte and write_byte are default */
+
+ /* hwcontrol always must be implemented */
+ nand->hwcontrol = s3c2410_hwcontrol;
+
+ nand->dev_ready = s3c2410_dev_ready;
+
+#ifdef CONFIG_S3C2410_NAND_HWECC
+ nand->enable_hwecc = s3c2410_nand_enable_hwecc;
+ nand->calculate_ecc = s3c2410_nand_calculate_ecc;
+ nand->correct_data = s3c2410_nand_correct_data;
+ nand->eccmode = NAND_ECC_HW3_512;
+#else
+ nand->eccmode = NAND_ECC_SOFT;
+#endif
+
+#ifdef CONFIG_S3C2410_NAND_BBT
+ nand->options = NAND_USE_FLASH_BBT;
+#else
+ nand->options = 0;
+#endif
+
+ DEBUGN("end of nand_init\n");
+
+ return 0;
+}
+
+#else
+ #error "U-Boot legacy NAND support not available for S3C2410"
+#endif
+#endif
diff --git a/cpu/arm920t/s3c24x0/serial.c b/cpu/arm920t/s3c24x0/serial.c
index 36851ad..6e853b8 100644
--- a/cpu/arm920t/s3c24x0/serial.c
+++ b/cpu/arm920t/s3c24x0/serial.c
@@ -48,18 +48,74 @@
#error "Bad: you didn't configure serial ..."
#endif
-void serial_setbrg (void)
+#if defined(CONFIG_SERIAL_MULTI)
+#include <serial.h>
+
+/* Multi serial device functions */
+#define DECLARE_S3C_SERIAL_FUNCTIONS(port) \
+ int s3serial##port##_init (void) {\
+ return serial_init_dev(port);}\
+ void s3serial##port##_setbrg (void) {\
+ serial_setbrg_dev(port);}\
+ int s3serial##port##_getc (void) {\
+ return serial_getc_dev(port);}\
+ int s3serial##port##_tstc (void) {\
+ return serial_tstc_dev(port);}\
+ void s3serial##port##_putc (const char c) {\
+ serial_putc_dev(port, c);}\
+ void s3serial##port##_puts (const char *s) {\
+ serial_puts_dev(port, s);}
+
+#define INIT_S3C_SERIAL_STRUCTURE(port,name,bus) {\
+ name,\
+ bus,\
+ s3serial##port##_init,\
+ s3serial##port##_setbrg,\
+ s3serial##port##_getc,\
+ s3serial##port##_tstc,\
+ s3serial##port##_putc,\
+ s3serial##port##_puts, }
+
+#endif /* CONFIG_SERIAL_MULTI */
+
+void _serial_setbrg(const int dev_index)
{
- S3C24X0_UART * const uart = S3C24X0_GetBase_UART(UART_NR);
- int i;
+ S3C24X0_UART * const uart = S3C24X0_GetBase_UART(dev_index);
unsigned int reg = 0;
+ int i;
/* value is calculated so : (int)(PCLK/16./baudrate) -1 */
reg = get_PCLK() / (16 * gd->baudrate) - 1;
+ uart->UBRDIV = reg;
+ for (i = 0; i < 100; i++);
+}
+#if defined(CONFIG_SERIAL_MULTI)
+static inline void
+serial_setbrg_dev(unsigned int dev_index)
+{
+ _serial_setbrg(dev_index);
+}
+#else
+void serial_setbrg(void)
+{
+ _serial_setbrg(UART_NR);
+}
+#endif
+
+
+/* Initialise the serial port. The settings are always 8 data bits, no parity,
+ * 1 stop bit, no start bits.
+ */
+static int serial_init_dev(const int dev_index)
+{
+ S3C24X0_UART * const uart = S3C24X0_GetBase_UART(dev_index);
+ int i;
+
/* FIFO enable, Tx/Rx FIFO clear */
uart->UFCON = 0x07;
uart->UMCON = 0x0;
+
/* Normal,No parity,1 stop,8 bit */
uart->ULCON = 0x3;
/*
@@ -67,40 +123,57 @@
* normal,interrupt or polling
*/
uart->UCON = 0x245;
- uart->UBRDIV = reg;
#ifdef CONFIG_HWFLOW
uart->UMCON = 0x1; /* RTS up */
#endif
- for (i = 0; i < 100; i++);
-}
-/*
- * Initialise the serial port with the given baudrate. The settings
- * are always 8 data bits, no parity, 1 stop bit, no start bits.
- *
- */
-int serial_init (void)
-{
- serial_setbrg ();
+ /* FIXME: This is sooooooooooooooooooo ugly */
+#if defined(CONFIG_ARCH_GTA02_v1) || defined(CONFIG_ARCH_GTA02_v2)
+ /* we need auto hw flow control on the gsm and gps port */
+ if (dev_index == 0 || dev_index == 1)
+ uart->UMCON = 0x10;
+#endif
+ _serial_setbrg(dev_index);
return (0);
}
+#if !defined(CONFIG_SERIAL_MULTI)
+/* Initialise the serial port. The settings are always 8 data bits, no parity,
+ * 1 stop bit, no start bits.
+ */
+int serial_init (void)
+{
+ return serial_init_dev(UART_NR);
+}
+#endif
+
/*
* Read a single byte from the serial port. Returns 1 on success, 0
* otherwise. When the function is succesfull, the character read is
* written into its argument c.
*/
-int serial_getc (void)
+int _serial_getc (const int dev_index)
{
- S3C24X0_UART * const uart = S3C24X0_GetBase_UART(UART_NR);
+ S3C24X0_UART * const uart = S3C24X0_GetBase_UART(dev_index);
/* wait for character to arrive */
while (!(uart->UTRSTAT & 0x1));
return uart->URXH & 0xff;
}
+#if defined(CONFIG_SERIAL_MULTI)
+static inline int serial_getc_dev(unsigned int dev_index)
+{
+ return _serial_getc(dev_index);
+}
+#else
+int serial_getc (void)
+{
+ return _serial_getc(UART_NR);
+}
+#endif
#ifdef CONFIG_HWFLOW
static int hwflow = 0; /* turned off by default */
@@ -138,9 +211,9 @@
/*
* Output a single byte to the serial port.
*/
-void serial_putc (const char c)
+void _serial_putc (const char c, const int dev_index)
{
- S3C24X0_UART * const uart = S3C24X0_GetBase_UART(UART_NR);
+ S3C24X0_UART * const uart = S3C24X0_GetBase_UART(dev_index);
#ifdef CONFIG_MODEM_SUPPORT
if (be_quiet)
return;
@@ -161,23 +234,72 @@
if (c == '\n')
serial_putc ('\r');
}
+#if defined(CONFIG_SERIAL_MULTI)
+static inline void serial_putc_dev(unsigned int dev_index, const char c)
+{
+ _serial_putc(c, dev_index);
+}
+#else
+void serial_putc(const char c)
+{
+ _serial_putc(c, UART_NR);
+}
+#endif
+
/*
* Test whether a character is in the RX buffer
*/
-int serial_tstc (void)
+int _serial_tstc(const int dev_index)
{
- S3C24X0_UART * const uart = S3C24X0_GetBase_UART(UART_NR);
+ S3C24X0_UART * const uart = S3C24X0_GetBase_UART(dev_index);
return uart->UTRSTAT & 0x1;
}
+#if defined(CONFIG_SERIAL_MULTI)
+static inline int
+serial_tstc_dev(unsigned int dev_index)
+{
+ return _serial_tstc(dev_index);
+}
+#else
+int serial_tstc(void)
+{
+ return _serial_tstc(UART_NR);
+}
+#endif
+void _serial_puts(const char *s, const int dev_index)
+{
+ while (*s) {
+ _serial_putc (*s++, dev_index);
+ }
+}
+#if defined(CONFIG_SERIAL_MULTI)
+static inline void
+serial_puts_dev(int dev_index, const char *s)
+{
+ _serial_puts(s, dev_index);
+}
+#else
void
serial_puts (const char *s)
{
- while (*s) {
- serial_putc (*s++);
- }
+ _serial_puts(s, UART_NR);
}
+#endif
+
+#if defined(CONFIG_SERIAL_MULTI)
+DECLARE_S3C_SERIAL_FUNCTIONS(0);
+struct serial_device s3c24xx_serial0_device =
+ INIT_S3C_SERIAL_STRUCTURE(0, "s3ser0", "S3UART1");
+DECLARE_S3C_SERIAL_FUNCTIONS(1);
+struct serial_device s3c24xx_serial1_device =
+ INIT_S3C_SERIAL_STRUCTURE(1, "s3ser1", "S3UART2");
+DECLARE_S3C_SERIAL_FUNCTIONS(2);
+struct serial_device s3c24xx_serial2_device =
+ INIT_S3C_SERIAL_STRUCTURE(2, "s3ser2", "S3UART3");
+
+#endif /* CONFIG_SERIAL_MULTI */
#endif /* defined(CONFIG_S3C2400) || defined (CONFIG_S3C2410) || defined (CONFIG_TRAB) */
diff --git a/cpu/arm920t/start.S b/cpu/arm920t/start.S
index aefcdd1..ae86002 100644
--- a/cpu/arm920t/start.S
+++ b/cpu/arm920t/start.S
@@ -329,12 +329,12 @@
.macro irq_save_user_regs
sub sp, sp, #S_FRAME_SIZE
stmia sp, {r0 - r12} @ Calling r0-r12
- add r8, sp, #S_PC
- stmdb r8, {sp, lr}^ @ Calling SP, LR
- str lr, [r8, #0] @ Save calling PC
+ add r7, sp, #S_PC
+ stmdb r7, {sp, lr}^ @ Calling SP, LR
+ str lr, [r7, #0] @ Save calling PC
mrs r6, spsr
- str r6, [r8, #4] @ Save CPSR
- str r0, [r8, #8] @ Save OLD_R0
+ str r6, [r7, #4] @ Save CPSR
+ str r0, [r7, #8] @ Save OLD_R0
mov r0, sp
.endm
diff --git a/cpu/mpc512x/cpu.c b/cpu/mpc512x/cpu.c
index 6421a51..bed77ac 100644
--- a/cpu/mpc512x/cpu.c
+++ b/cpu/mpc512x/cpu.c
@@ -138,11 +138,11 @@
do_fixup_by_path_u32(blob, cpu_path, "timebase-frequency", OF_TBCLK, 1);
do_fixup_by_path_u32(blob, cpu_path, "bus-frequency", bd->bi_busfreq, 1);
- do_fixup_by_path_u32(blob, cpu_path, "ref-frequency", CFG_MPC512X_CLKIN, 1);
do_fixup_by_path_u32(blob, cpu_path, "clock-frequency", bd->bi_intfreq, 1);
do_fixup_by_path_u32(blob, "/" OF_SOC, "bus-frequency", bd->bi_ipsfreq, 1);
- do_fixup_by_path_u32(blob, "/" OF_SOC, "ref-frequency", CFG_MPC512X_CLKIN, 1);
- do_fixup_by_path(blob, eth_path, "address", bd->bi_enetaddr, 6, 0);
do_fixup_by_path(blob, eth_path, "local-mac-address", bd->bi_enetaddr, 6, 0);
+
+ /* this is so old kernels with old device trees will boot */
+ do_fixup_by_path_u32(blob, "/" OF_SOC_OLD, "bus-frequency", bd->bi_ipsfreq, 0);
}
#endif
diff --git a/cpu/mpc83xx/fdt.c b/cpu/mpc83xx/fdt.c
index 909171f..6f55932 100644
--- a/cpu/mpc83xx/fdt.c
+++ b/cpu/mpc83xx/fdt.c
@@ -30,6 +30,8 @@
#include <libfdt.h>
#include <fdt_support.h>
+extern void ft_qe_setup(void *blob);
+
DECLARE_GLOBAL_DATA_PTR;
void ft_cpu_setup(void *blob, bd_t *bd)
@@ -48,16 +50,7 @@
do_fixup_by_prop_u32(blob, "device_type", "soc", 4,
"bus-frequency", bd->bi_busfreq, 1);
#ifdef CONFIG_QE
- do_fixup_by_prop_u32(blob, "device_type", "qe", 4,
- "bus-frequency", gd->qe_clk, 1);
- do_fixup_by_prop_u32(blob, "device_type", "qe", 4,
- "brg-frequency", gd->brg_clk, 1);
- do_fixup_by_compat_u32(blob, "fsl,qe",
- "clock-frequency", gd->qe_clk, 1);
- do_fixup_by_compat_u32(blob, "fsl,qe",
- "bus-frequency", gd->qe_clk, 1);
- do_fixup_by_compat_u32(blob, "fsl,qe",
- "brg-frequency", gd->brg_clk, 1);
+ ft_qe_setup(blob);
#endif
#ifdef CFG_NS16550
diff --git a/cpu/mpc85xx/fdt.c b/cpu/mpc85xx/fdt.c
index 0ce17e7..a6b014c 100644
--- a/cpu/mpc85xx/fdt.c
+++ b/cpu/mpc85xx/fdt.c
@@ -27,6 +27,8 @@
#include <libfdt.h>
#include <fdt_support.h>
+extern void ft_qe_setup(void *blob);
+
void ft_cpu_setup(void *blob, bd_t *bd)
{
#if defined(CONFIG_HAS_ETH0) || defined(CONFIG_HAS_ETH1) ||\
@@ -43,11 +45,7 @@
do_fixup_by_prop_u32(blob, "device_type", "soc", 4,
"bus-frequency", bd->bi_busfreq, 1);
#ifdef CONFIG_QE
- do_fixup_by_prop_u32(blob, "device_type", "qe", 4,
- "bus-frequency", bd->bi_busfreq, 1);
- do_fixup_by_prop_u32(blob, "device_type", "qe", 4,
- "brg-frequency", bd->bi_busfreq / 2, 1);
- fdt_fixup_qe_firmware(blob);
+ ft_qe_setup(blob);
#endif
#ifdef CFG_NS16550
diff --git a/cpu/pxa/mmc.c b/cpu/pxa/mmc.c
index d76e0cd..c0cfe65 100644
--- a/cpu/pxa/mmc.c
+++ b/cpu/pxa/mmc.c
@@ -30,14 +30,13 @@
#ifdef CONFIG_MMC
-extern int
-fat_register_device(block_dev_desc_t *dev_desc, int part_no);
+extern int fat_register_device(block_dev_desc_t * dev_desc, int part_no);
static block_dev_desc_t mmc_dev;
-block_dev_desc_t * mmc_get_dev(int dev)
+block_dev_desc_t *mmc_get_dev(int dev)
{
- return (dev == 0) ? &mmc_dev : NULL;
+ return ((block_dev_desc_t *) & mmc_dev);
}
/*
@@ -45,72 +44,59 @@
* and other parameters
*/
static uchar mmc_buf[MMC_BLOCK_SIZE];
-static mmc_csd_t mmc_csd;
+static uchar spec_ver;
static int mmc_ready = 0;
+static int wide = 0;
-
-static uchar *
+static uint32_t *
/****************************************************/
mmc_cmd(ushort cmd, ushort argh, ushort argl, ushort cmdat)
/****************************************************/
{
- static uchar resp[20];
+ static uint32_t resp[4], a, b, c;
ulong status;
- int words, i;
+ int i;
- debug("mmc_cmd %x %x %x %x\n", cmd, argh, argl, cmdat);
+ debug("mmc_cmd %u 0x%04x 0x%04x 0x%04x\n", cmd, argh, argl,
+ cmdat | wide);
MMC_STRPCL = MMC_STRPCL_STOP_CLK;
MMC_I_MASK = ~MMC_I_MASK_CLK_IS_OFF;
- while (!(MMC_I_REG & MMC_I_REG_CLK_IS_OFF));
- MMC_CMD = cmd;
- MMC_ARGH = argh;
- MMC_ARGL = argl;
- MMC_CMDAT = cmdat;
+ while (!(MMC_I_REG & MMC_I_REG_CLK_IS_OFF)) ;
+ MMC_CMD = cmd;
+ MMC_ARGH = argh;
+ MMC_ARGL = argl;
+ MMC_CMDAT = cmdat | wide;
MMC_I_MASK = ~MMC_I_MASK_END_CMD_RES;
MMC_STRPCL = MMC_STRPCL_START_CLK;
- while (!(MMC_I_REG & MMC_I_REG_END_CMD_RES));
+ while (!(MMC_I_REG & MMC_I_REG_END_CMD_RES)) ;
status = MMC_STAT;
- debug("MMC status %x\n", status);
+ debug("MMC status 0x%08x\n", status);
if (status & MMC_STAT_TIME_OUT_RESPONSE) {
return 0;
}
- switch (cmdat & 0x3) {
- case MMC_CMDAT_R1:
- case MMC_CMDAT_R3:
- words = 3;
- break;
-
- case MMC_CMDAT_R2:
- words = 8;
- break;
-
- default:
- return 0;
+ /* Linux says:
+ * Did I mention this is Sick. We always need to
+ * discard the upper 8 bits of the first 16-bit word.
+ */
+ a = (MMC_RES & 0xffff);
+ for (i = 0; i < 4; i++) {
+ b = (MMC_RES & 0xffff);
+ c = (MMC_RES & 0xffff);
+ resp[i] = (a << 24) | (b << 8) | (c >> 8);
+ a = c;
+ debug("MMC resp[%d] = %#08x\n", i, resp[i]);
}
- for (i = words-1; i >= 0; i--) {
- ulong res_fifo = MMC_RES;
- int offset = i << 1;
- resp[offset] = ((uchar *)&res_fifo)[0];
- resp[offset+1] = ((uchar *)&res_fifo)[1];
- }
-#ifdef MMC_DEBUG
- for (i=0; i<words*2; i += 2) {
- printf("MMC resp[%d] = %02x\n", i, resp[i]);
- printf("MMC resp[%d] = %02x\n", i+1, resp[i+1]);
- }
-#endif
return resp;
}
int
/****************************************************/
-mmc_block_read(uchar *dst, ulong src, ulong len)
+mmc_block_read(uchar * dst, ulong src, ulong len)
/****************************************************/
{
- uchar *resp;
ushort argh, argl;
ulong status;
@@ -118,13 +104,13 @@
return 0;
}
- debug("mmc_block_rd dst %lx src %lx len %d\n", (ulong)dst, src, len);
+ debug("mmc_block_rd dst %lx src %lx len %d\n", (ulong) dst, src, len);
argh = len >> 16;
argl = len & 0xffff;
/* set block len */
- resp = mmc_cmd(MMC_CMD_SET_BLOCKLEN, argh, argl, MMC_CMDAT_R1);
+ mmc_cmd(MMC_CMD_SET_BLOCKLEN, argh, argl, MMC_CMDAT_R1);
/* send read command */
argh = src >> 16;
@@ -133,17 +119,17 @@
MMC_RDTO = 0xffff;
MMC_NOB = 1;
MMC_BLKLEN = len;
- resp = mmc_cmd(MMC_CMD_READ_BLOCK, argh, argl,
- MMC_CMDAT_R1|MMC_CMDAT_READ|MMC_CMDAT_BLOCK|MMC_CMDAT_DATA_EN);
-
+ mmc_cmd(MMC_CMD_READ_BLOCK, argh, argl,
+ MMC_CMDAT_R1 | MMC_CMDAT_READ | MMC_CMDAT_BLOCK |
+ MMC_CMDAT_DATA_EN);
MMC_I_MASK = ~MMC_I_MASK_RXFIFO_RD_REQ;
while (len) {
if (MMC_I_REG & MMC_I_REG_RXFIFO_RD_REQ) {
#ifdef CONFIG_PXA27X
int i;
- for (i=min(len,32); i; i--) {
- *dst++ = * ((volatile uchar *) &MMC_RXFIFO);
+ for (i = min(len, 32); i; i--) {
+ *dst++ = *((volatile uchar *)&MMC_RXFIFO);
len--;
}
#else
@@ -158,7 +144,7 @@
}
}
MMC_I_MASK = ~MMC_I_MASK_DATA_TRAN_DONE;
- while (!(MMC_I_REG & MMC_I_REG_DATA_TRAN_DONE));
+ while (!(MMC_I_REG & MMC_I_REG_DATA_TRAN_DONE)) ;
status = MMC_STAT;
if (status & MMC_STAT_ERRORS) {
printf("MMC_STAT error %lx\n", status);
@@ -169,10 +155,9 @@
int
/****************************************************/
-mmc_block_write(ulong dst, uchar *src, int len)
+mmc_block_write(ulong dst, uchar * src, int len)
/****************************************************/
{
- uchar *resp;
ushort argh, argl;
ulong status;
@@ -180,13 +165,13 @@
return 0;
}
- debug("mmc_block_wr dst %lx src %lx len %d\n", dst, (ulong)src, len);
+ debug("mmc_block_wr dst %lx src %lx len %d\n", dst, (ulong) src, len);
argh = len >> 16;
argl = len & 0xffff;
/* set block len */
- resp = mmc_cmd(MMC_CMD_SET_BLOCKLEN, argh, argl, MMC_CMDAT_R1);
+ mmc_cmd(MMC_CMD_SET_BLOCKLEN, argh, argl, MMC_CMDAT_R1);
/* send write command */
argh = dst >> 16;
@@ -194,15 +179,16 @@
MMC_STRPCL = MMC_STRPCL_STOP_CLK;
MMC_NOB = 1;
MMC_BLKLEN = len;
- resp = mmc_cmd(MMC_CMD_WRITE_BLOCK, argh, argl,
- MMC_CMDAT_R1|MMC_CMDAT_WRITE|MMC_CMDAT_BLOCK|MMC_CMDAT_DATA_EN);
+ mmc_cmd(MMC_CMD_WRITE_BLOCK, argh, argl,
+ MMC_CMDAT_R1 | MMC_CMDAT_WRITE | MMC_CMDAT_BLOCK |
+ MMC_CMDAT_DATA_EN);
MMC_I_MASK = ~MMC_I_MASK_TXFIFO_WR_REQ;
while (len) {
if (MMC_I_REG & MMC_I_REG_TXFIFO_WR_REQ) {
- int i, bytes = min(32,len);
+ int i, bytes = min(32, len);
- for (i=0; i<bytes; i++) {
+ for (i = 0; i < bytes; i++) {
MMC_TXFIFO = *src++;
}
if (bytes < 32) {
@@ -217,9 +203,9 @@
}
}
MMC_I_MASK = ~MMC_I_MASK_DATA_TRAN_DONE;
- while (!(MMC_I_REG & MMC_I_REG_DATA_TRAN_DONE));
+ while (!(MMC_I_REG & MMC_I_REG_DATA_TRAN_DONE)) ;
MMC_I_MASK = ~MMC_I_MASK_PRG_DONE;
- while (!(MMC_I_REG & MMC_I_REG_PRG_DONE));
+ while (!(MMC_I_REG & MMC_I_REG_PRG_DONE)) ;
status = MMC_STAT;
if (status & MMC_STAT_ERRORS) {
printf("MMC_STAT error %lx\n", status);
@@ -228,10 +214,9 @@
return 0;
}
-
int
/****************************************************/
-mmc_read(ulong src, uchar *dst, int size)
+mmc_read(ulong src, uchar * dst, int size)
/****************************************************/
{
ulong end, part_start, part_end, part_len, aligned_start, aligned_end;
@@ -257,33 +242,46 @@
aligned_end = mmc_block_address & end;
/* all block aligned accesses */
- debug("src %lx dst %lx end %lx pstart %lx pend %lx astart %lx aend %lx\n",
- src, (ulong)dst, end, part_start, part_end, aligned_start, aligned_end);
+ debug
+ ("src %lx dst %lx end %lx pstart %lx pend %lx astart %lx aend %lx\n",
+ src, (ulong) dst, end, part_start, part_end, aligned_start,
+ aligned_end);
if (part_start) {
part_len = mmc_block_size - part_start;
- debug("ps src %lx dst %lx end %lx pstart %lx pend %lx astart %lx aend %lx\n",
- src, (ulong)dst, end, part_start, part_end, aligned_start, aligned_end);
- if ((mmc_block_read(mmc_buf, aligned_start, mmc_block_size)) < 0) {
+ debug
+ ("ps src %lx dst %lx end %lx pstart %lx pend %lx astart %lx aend %lx\n",
+ src, (ulong) dst, end, part_start, part_end, aligned_start,
+ aligned_end);
+ if ((mmc_block_read(mmc_buf, aligned_start, mmc_block_size)) <
+ 0) {
return -1;
}
- memcpy(dst, mmc_buf+part_start, part_len);
+ memcpy(dst, mmc_buf + part_start, part_len);
dst += part_len;
src += part_len;
}
- debug("src %lx dst %lx end %lx pstart %lx pend %lx astart %lx aend %lx\n",
- src, (ulong)dst, end, part_start, part_end, aligned_start, aligned_end);
+ debug
+ ("src %lx dst %lx end %lx pstart %lx pend %lx astart %lx aend %lx\n",
+ src, (ulong) dst, end, part_start, part_end, aligned_start,
+ aligned_end);
for (; src < aligned_end; src += mmc_block_size, dst += mmc_block_size) {
- debug("al src %lx dst %lx end %lx pstart %lx pend %lx astart %lx aend %lx\n",
- src, (ulong)dst, end, part_start, part_end, aligned_start, aligned_end);
- if ((mmc_block_read((uchar *)(dst), src, mmc_block_size)) < 0) {
+ debug
+ ("al src %lx dst %lx end %lx pstart %lx pend %lx astart %lx aend %lx\n",
+ src, (ulong) dst, end, part_start, part_end, aligned_start,
+ aligned_end);
+ if ((mmc_block_read((uchar *) (dst), src, mmc_block_size)) < 0) {
return -1;
}
}
- debug("src %lx dst %lx end %lx pstart %lx pend %lx astart %lx aend %lx\n",
- src, (ulong)dst, end, part_start, part_end, aligned_start, aligned_end);
+ debug
+ ("src %lx dst %lx end %lx pstart %lx pend %lx astart %lx aend %lx\n",
+ src, (ulong) dst, end, part_start, part_end, aligned_start,
+ aligned_end);
if (part_end && src < end) {
- debug("pe src %lx dst %lx end %lx pstart %lx pend %lx astart %lx aend %lx\n",
- src, (ulong)dst, end, part_start, part_end, aligned_start, aligned_end);
+ debug
+ ("pe src %lx dst %lx end %lx pstart %lx pend %lx astart %lx aend %lx\n",
+ src, (ulong) dst, end, part_start, part_end, aligned_start,
+ aligned_end);
if ((mmc_block_read(mmc_buf, aligned_end, mmc_block_size)) < 0) {
return -1;
}
@@ -294,7 +292,7 @@
int
/****************************************************/
-mmc_write(uchar *src, ulong dst, int size)
+mmc_write(uchar * src, ulong dst, int size)
/****************************************************/
{
ulong end, part_start, part_end, part_len, aligned_start, aligned_end;
@@ -320,36 +318,50 @@
aligned_end = mmc_block_address & end;
/* all block aligned accesses */
- debug("src %lx dst %lx end %lx pstart %lx pend %lx astart %lx aend %lx\n",
- src, (ulong)dst, end, part_start, part_end, aligned_start, aligned_end);
+ debug
+ ("src %lx dst %lx end %lx pstart %lx pend %lx astart %lx aend %lx\n",
+ src, (ulong) dst, end, part_start, part_end, aligned_start,
+ aligned_end);
if (part_start) {
part_len = mmc_block_size - part_start;
- debug("ps src %lx dst %lx end %lx pstart %lx pend %lx astart %lx aend %lx\n",
- (ulong)src, dst, end, part_start, part_end, aligned_start, aligned_end);
- if ((mmc_block_read(mmc_buf, aligned_start, mmc_block_size)) < 0) {
+ debug
+ ("ps src %lx dst %lx end %lx pstart %lx pend %lx astart %lx aend %lx\n",
+ (ulong) src, dst, end, part_start, part_end, aligned_start,
+ aligned_end);
+ if ((mmc_block_read(mmc_buf, aligned_start, mmc_block_size)) <
+ 0) {
return -1;
}
- memcpy(mmc_buf+part_start, src, part_len);
- if ((mmc_block_write(aligned_start, mmc_buf, mmc_block_size)) < 0) {
+ memcpy(mmc_buf + part_start, src, part_len);
+ if ((mmc_block_write(aligned_start, mmc_buf, mmc_block_size)) <
+ 0) {
return -1;
}
dst += part_len;
src += part_len;
}
- debug("src %lx dst %lx end %lx pstart %lx pend %lx astart %lx aend %lx\n",
- src, (ulong)dst, end, part_start, part_end, aligned_start, aligned_end);
+ debug
+ ("src %lx dst %lx end %lx pstart %lx pend %lx astart %lx aend %lx\n",
+ src, (ulong) dst, end, part_start, part_end, aligned_start,
+ aligned_end);
for (; dst < aligned_end; src += mmc_block_size, dst += mmc_block_size) {
- debug("al src %lx dst %lx end %lx pstart %lx pend %lx astart %lx aend %lx\n",
- src, (ulong)dst, end, part_start, part_end, aligned_start, aligned_end);
- if ((mmc_block_write(dst, (uchar *)src, mmc_block_size)) < 0) {
+ debug
+ ("al src %lx dst %lx end %lx pstart %lx pend %lx astart %lx aend %lx\n",
+ src, (ulong) dst, end, part_start, part_end, aligned_start,
+ aligned_end);
+ if ((mmc_block_write(dst, (uchar *) src, mmc_block_size)) < 0) {
return -1;
}
}
- debug("src %lx dst %lx end %lx pstart %lx pend %lx astart %lx aend %lx\n",
- src, (ulong)dst, end, part_start, part_end, aligned_start, aligned_end);
+ debug
+ ("src %lx dst %lx end %lx pstart %lx pend %lx astart %lx aend %lx\n",
+ src, (ulong) dst, end, part_start, part_end, aligned_start,
+ aligned_end);
if (part_end && dst < end) {
- debug("pe src %lx dst %lx end %lx pstart %lx pend %lx astart %lx aend %lx\n",
- src, (ulong)dst, end, part_start, part_end, aligned_start, aligned_end);
+ debug
+ ("pe src %lx dst %lx end %lx pstart %lx pend %lx astart %lx aend %lx\n",
+ src, (ulong) dst, end, part_start, part_end, aligned_start,
+ aligned_end);
if ((mmc_block_read(mmc_buf, aligned_end, mmc_block_size)) < 0) {
return -1;
}
@@ -363,127 +375,288 @@
ulong
/****************************************************/
-mmc_bread(int dev_num, ulong blknr, ulong blkcnt, void *dst)
+mmc_bread(int dev_num, ulong blknr, ulong blkcnt, ulong * dst)
/****************************************************/
{
int mmc_block_size = MMC_BLOCK_SIZE;
ulong src = blknr * mmc_block_size + CFG_MMC_BASE;
- mmc_read(src, (uchar *)dst, blkcnt*mmc_block_size);
+ mmc_read(src, (uchar *) dst, blkcnt * mmc_block_size);
return blkcnt;
}
+#ifdef __GNUC__
+#define likely(x) __builtin_expect(!!(x), 1)
+#define unlikely(x) __builtin_expect(!!(x), 0)
+#else
+#define likely(x) (x)
+#define unlikely(x) (x)
+#endif
+
+#define UNSTUFF_BITS(resp,start,size) \
+ ({ \
+ const int __size = size; \
+ const uint32_t __mask = (__size < 32 ? 1 << __size : 0) - 1; \
+ const int32_t __off = 3 - ((start) / 32); \
+ const int32_t __shft = (start) & 31; \
+ uint32_t __res; \
+ \
+ __res = resp[__off] >> __shft; \
+ if (__size + __shft > 32) \
+ __res |= resp[__off-1] << ((32 - __shft) % 32); \
+ __res & __mask; \
+ })
+
+/*
+ * Given the decoded CSD structure, decode the raw CID to our CID structure.
+ */
+static void mmc_decode_cid(uint32_t * resp)
+{
+ if (IF_TYPE_SD == mmc_dev.if_type) {
+ /*
+ * SD doesn't currently have a version field so we will
+ * have to assume we can parse this.
+ */
+ sprintf((char *)mmc_dev.vendor,
+ "Man %02x OEM %c%c \"%c%c%c%c%c\" Date %02u/%04u",
+ UNSTUFF_BITS(resp, 120, 8), UNSTUFF_BITS(resp, 112, 8),
+ UNSTUFF_BITS(resp, 104, 8), UNSTUFF_BITS(resp, 96, 8),
+ UNSTUFF_BITS(resp, 88, 8), UNSTUFF_BITS(resp, 80, 8),
+ UNSTUFF_BITS(resp, 72, 8), UNSTUFF_BITS(resp, 64, 8),
+ UNSTUFF_BITS(resp, 8, 4), UNSTUFF_BITS(resp, 12,
+ 8) + 2000);
+ sprintf((char *)mmc_dev.revision, "%d.%d",
+ UNSTUFF_BITS(resp, 60, 4), UNSTUFF_BITS(resp, 56, 4));
+ sprintf((char *)mmc_dev.product, "%u",
+ UNSTUFF_BITS(resp, 24, 32));
+ } else {
+ /*
+ * The selection of the format here is based upon published
+ * specs from sandisk and from what people have reported.
+ */
+ switch (spec_ver) {
+ case 0: /* MMC v1.0 - v1.2 */
+ case 1: /* MMC v1.4 */
+ sprintf((char *)mmc_dev.vendor,
+ "Man %02x%02x%02x \"%c%c%c%c%c%c%c\" Date %02u/%04u",
+ UNSTUFF_BITS(resp, 120, 8), UNSTUFF_BITS(resp,
+ 112,
+ 8),
+ UNSTUFF_BITS(resp, 104, 8), UNSTUFF_BITS(resp,
+ 96, 8),
+ UNSTUFF_BITS(resp, 88, 8), UNSTUFF_BITS(resp,
+ 80, 8),
+ UNSTUFF_BITS(resp, 72, 8), UNSTUFF_BITS(resp,
+ 64, 8),
+ UNSTUFF_BITS(resp, 56, 8), UNSTUFF_BITS(resp,
+ 48, 8),
+ UNSTUFF_BITS(resp, 12, 4), UNSTUFF_BITS(resp, 8,
+ 4) +
+ 1997);
+ sprintf((char *)mmc_dev.revision, "%d.%d",
+ UNSTUFF_BITS(resp, 44, 4), UNSTUFF_BITS(resp,
+ 40, 4));
+ sprintf((char *)mmc_dev.product, "%u",
+ UNSTUFF_BITS(resp, 16, 24));
+ break;
+
+ case 2: /* MMC v2.0 - v2.2 */
+ case 3: /* MMC v3.1 - v3.3 */
+ case 4: /* MMC v4 */
+ sprintf((char *)mmc_dev.vendor,
+ "Man %02x OEM %04x \"%c%c%c%c%c%c\" Date %02u/%04u",
+ UNSTUFF_BITS(resp, 120, 8), UNSTUFF_BITS(resp,
+ 104,
+ 16),
+ UNSTUFF_BITS(resp, 96, 8), UNSTUFF_BITS(resp,
+ 88, 8),
+ UNSTUFF_BITS(resp, 80, 8), UNSTUFF_BITS(resp,
+ 72, 8),
+ UNSTUFF_BITS(resp, 64, 8), UNSTUFF_BITS(resp,
+ 56, 8),
+ UNSTUFF_BITS(resp, 12, 4), UNSTUFF_BITS(resp, 8,
+ 4) +
+ 1997);
+ sprintf((char *)mmc_dev.product, "%u",
+ UNSTUFF_BITS(resp, 16, 32));
+ sprintf((char *)mmc_dev.revision, "N/A");
+ break;
+
+ default:
+ printf("MMC card has unknown MMCA version %d\n",
+ spec_ver);
+ break;
+ }
+ }
+ printf("%s card.\nVendor: %s\nProduct: %s\nRevision: %s\n",
+ (IF_TYPE_SD == mmc_dev.if_type) ? "SD" : "MMC", mmc_dev.vendor,
+ mmc_dev.product, mmc_dev.revision);
+}
+
+/*
+ * Given a 128-bit response, decode to our card CSD structure.
+ */
+static void mmc_decode_csd(uint32_t * resp)
+{
+ unsigned int mult, csd_struct;
+
+ if (IF_TYPE_SD == mmc_dev.if_type) {
+ csd_struct = UNSTUFF_BITS(resp, 126, 2);
+ if (csd_struct != 0) {
+ printf("SD: unrecognised CSD structure version %d\n",
+ csd_struct);
+ return;
+ }
+ } else {
+ /*
+ * We only understand CSD structure v1.1 and v1.2.
+ * v1.2 has extra information in bits 15, 11 and 10.
+ */
+ csd_struct = UNSTUFF_BITS(resp, 126, 2);
+ if (csd_struct != 1 && csd_struct != 2) {
+ printf("MMC: unrecognised CSD structure version %d\n",
+ csd_struct);
+ return;
+ }
+
+ spec_ver = UNSTUFF_BITS(resp, 122, 4);
+ mmc_dev.if_type = IF_TYPE_MMC;
+ }
+
+ mult = 1 << (UNSTUFF_BITS(resp, 47, 3) + 2);
+ mmc_dev.lba = (1 + UNSTUFF_BITS(resp, 62, 12)) * mult;
+ mmc_dev.blksz = 1 << UNSTUFF_BITS(resp, 80, 4);
+
+ /* FIXME: The following just makes assumes that's the partition type -- should really read it */
+ mmc_dev.part_type = PART_TYPE_DOS;
+ mmc_dev.dev = 0;
+ mmc_dev.lun = 0;
+ mmc_dev.type = DEV_TYPE_HARDDISK;
+ mmc_dev.removable = 0;
+ mmc_dev.block_read = mmc_bread;
+
+ printf("Detected: %u blocks of %u bytes (%uMB) ", mmc_dev.lba,
+ mmc_dev.blksz, mmc_dev.lba * mmc_dev.blksz / (1024 * 1024));
+}
+
int
/****************************************************/
mmc_init(int verbose)
/****************************************************/
{
- int retries, rc = -ENODEV;
- uchar *resp;
+ int retries, rc = -ENODEV;
+ uint32_t cid_resp[4];
+ uint32_t *resp;
+ uint16_t rca = 0;
-#ifdef CONFIG_LUBBOCK
- set_GPIO_mode( GPIO6_MMCCLK_MD );
- set_GPIO_mode( GPIO8_MMCCS0_MD );
+ /* Reset device interface type */
+ mmc_dev.if_type = IF_TYPE_UNKNOWN;
+
+#if defined (CONFIG_LUBBOCK) || (defined (CONFIG_GUMSTIX) && !defined(CONFIG_PXA27X))
+ set_GPIO_mode(GPIO6_MMCCLK_MD);
+ set_GPIO_mode(GPIO8_MMCCS0_MD);
#endif
- CKEN |= CKEN12_MMC; /* enable MMC unit clock */
+ CKEN |= CKEN12_MMC; /* enable MMC unit clock */
#if defined(CONFIG_ADSVIX)
/* turn on the power */
GPCR(114) = GPIO_bit(114);
udelay(1000);
#endif
- mmc_csd.c_size = 0;
-
- MMC_CLKRT = MMC_CLKRT_0_3125MHZ;
- MMC_RESTO = MMC_RES_TO_MAX;
- MMC_SPI = MMC_SPI_DISABLE;
+ MMC_CLKRT = MMC_CLKRT_0_3125MHZ;
+ MMC_RESTO = MMC_RES_TO_MAX;
+ MMC_SPI = MMC_SPI_DISABLE;
/* reset */
- retries = 10;
- resp = mmc_cmd(0, 0, 0, 0);
- resp = mmc_cmd(1, 0x00ff, 0xc000, MMC_CMDAT_INIT|MMC_CMDAT_BUSY|MMC_CMDAT_R3);
- while (retries-- && resp && !(resp[4] & 0x80)) {
- debug("resp %x %x\n", resp[0], resp[1]);
+ mmc_cmd(MMC_CMD_RESET, 0, 0, MMC_CMDAT_INIT | MMC_CMDAT_R0);
+ udelay(200000);
+ retries = 3;
+ while (retries--) {
+ resp = mmc_cmd(MMC_CMD_APP_CMD, 0, 0, MMC_CMDAT_R1);
+ if (!(resp[0] & 0x00000020)) { /* Card does not support APP_CMD */
+ debug("Card does not support APP_CMD\n");
+ break;
+ }
+
+ resp = mmc_cmd(SD_CMD_APP_OP_COND, 0x0020, 0, MMC_CMDAT_R3 | (retries < 2 ? 0 : MMC_CMDAT_INIT)); /* Select 3.2-3.3 and 3.3-3.4V */
+ if (resp[0] & 0x80000000) {
+ mmc_dev.if_type = IF_TYPE_SD;
+ debug("Detected SD card\n");
+ break;
+ }
#ifdef CONFIG_PXA27X
udelay(10000);
#else
- udelay(50);
+ udelay(200000);
#endif
- resp = mmc_cmd(1, 0x00ff, 0xff00, MMC_CMDAT_BUSY|MMC_CMDAT_R3);
+ }
+
+ if (retries <= 0 || !(IF_TYPE_SD == mmc_dev.if_type)) {
+ debug("Failed to detect SD Card, trying MMC\n");
+ resp =
+ mmc_cmd(MMC_CMD_SEND_OP_COND, 0x00ff, 0x8000, MMC_CMDAT_R3);
+
+ retries = 10;
+ while (retries-- && resp && !(resp[0] & 0x80000000)) {
+#ifdef CONFIG_PXA27X
+ udelay(10000);
+#else
+ udelay(200000);
+#endif
+ resp =
+ mmc_cmd(MMC_CMD_SEND_OP_COND, 0x00ff, 0x8000,
+ MMC_CMDAT_R3);
+ }
}
/* try to get card id */
- resp = mmc_cmd(2, 0, 0, MMC_CMDAT_R2);
+ resp =
+ mmc_cmd(MMC_CMD_ALL_SEND_CID, 0, 0, MMC_CMDAT_R2 | MMC_CMDAT_BUSY);
if (resp) {
- /* TODO configure mmc driver depending on card attributes */
- mmc_cid_t *cid = (mmc_cid_t *)resp;
- if (verbose) {
- printf("MMC found. Card desciption is:\n");
- printf("Manufacturer ID = %02x%02x%02x\n",
- cid->id[0], cid->id[1], cid->id[2]);
- printf("HW/FW Revision = %x %x\n",cid->hwrev, cid->fwrev);
- cid->hwrev = cid->fwrev = 0; /* null terminate string */
- printf("Product Name = %s\n",cid->name);
- printf("Serial Number = %02x%02x%02x\n",
- cid->sn[0], cid->sn[1], cid->sn[2]);
- printf("Month = %d\n",cid->month);
- printf("Year = %d\n",1997 + cid->year);
- }
- /* fill in device description */
- mmc_dev.if_type = IF_TYPE_MMC;
- mmc_dev.part_type = PART_TYPE_DOS;
- mmc_dev.dev = 0;
- mmc_dev.lun = 0;
- mmc_dev.type = 0;
- /* FIXME fill in the correct size (is set to 32MByte) */
- mmc_dev.blksz = 512;
- mmc_dev.lba = 0x10000;
- sprintf((char*)mmc_dev.vendor,"Man %02x%02x%02x Snr %02x%02x%02x",
- cid->id[0], cid->id[1], cid->id[2],
- cid->sn[0], cid->sn[1], cid->sn[2]);
- sprintf((char*)mmc_dev.product,"%s",cid->name);
- sprintf((char*)mmc_dev.revision,"%x %x",cid->hwrev, cid->fwrev);
- mmc_dev.removable = 0;
- mmc_dev.block_read = mmc_bread;
+ memcpy(cid_resp, resp, sizeof(cid_resp));
/* MMC exists, get CSD too */
- resp = mmc_cmd(MMC_CMD_SET_RCA, MMC_DEFAULT_RCA, 0, MMC_CMDAT_R1);
- resp = mmc_cmd(MMC_CMD_SEND_CSD, MMC_DEFAULT_RCA, 0, MMC_CMDAT_R2);
+ resp = mmc_cmd(MMC_CMD_SET_RCA, 0, 0, MMC_CMDAT_R1);
+ if (IF_TYPE_SD == mmc_dev.if_type)
+ rca = ((resp[0] & 0xffff0000) >> 16);
+ resp = mmc_cmd(MMC_CMD_SEND_CSD, rca, 0, MMC_CMDAT_R2);
if (resp) {
- mmc_csd_t *csd = (mmc_csd_t *)resp;
- memcpy(&mmc_csd, csd, sizeof(csd));
+ mmc_decode_csd(resp);
rc = 0;
mmc_ready = 1;
- /* FIXME add verbose printout for csd */
}
+
+ mmc_decode_cid(cid_resp);
}
-#ifdef CONFIG_PXA27X
- MMC_CLKRT = 1; /* 10 MHz - see Intel errata */
-#else
- MMC_CLKRT = 0; /* 20 MHz */
-#endif
- resp = mmc_cmd(7, MMC_DEFAULT_RCA, 0, MMC_CMDAT_R1);
+ MMC_CLKRT = 0; /* 20 MHz */
+ resp = mmc_cmd(MMC_CMD_SELECT_CARD, rca, 0, MMC_CMDAT_R1);
- fat_register_device(&mmc_dev,1); /* partitions start counting with 1 */
+#ifdef CONFIG_PXA27X
+ if (IF_TYPE_SD == mmc_dev.if_type) {
+ resp = mmc_cmd(MMC_CMD_APP_CMD, rca, 0, MMC_CMDAT_R1);
+ resp = mmc_cmd(SD_CMD_APP_SET_BUS_WIDTH, 0, 2, MMC_CMDAT_R1);
+ wide = MMC_CMDAT_SD_4DAT;
+ }
+#endif
+
+ fat_register_device(&mmc_dev, 1); /* partitions start counting with 1 */
return rc;
}
-int
-mmc_ident(block_dev_desc_t *dev)
+int mmc_ident(block_dev_desc_t * dev)
{
return 0;
}
-int
-mmc2info(ulong addr)
+int mmc2info(ulong addr)
{
- /* FIXME hard codes to 32 MB device */
- if (addr >= CFG_MMC_BASE && addr < CFG_MMC_BASE + 0x02000000) {
+ if (addr >= CFG_MMC_BASE
+ && addr < CFG_MMC_BASE + (mmc_dev.lba * mmc_dev.blksz)) {
return 1;
}
return 0;
}
-#endif /* CONFIG_MMC */
+#endif /* CONFIG_MMC */
diff --git a/drivers/qe/Makefile b/drivers/qe/Makefile
index 4844181..ec5aa73 100644
--- a/drivers/qe/Makefile
+++ b/drivers/qe/Makefile
@@ -24,7 +24,8 @@
LIB := $(obj)qe.a
-COBJS := qe.o uccf.o uec.o uec_phy.o
+COBJS-$(CONFIG_OF_LIBFDT) += fdt.o
+COBJS := qe.o uccf.o uec.o uec_phy.o $(COBJS-y)
SRCS := $(COBJS:.o=.c)
OBJS := $(addprefix $(obj),$(COBJS))
diff --git a/drivers/qe/fdt.c b/drivers/qe/fdt.c
new file mode 100644
index 0000000..5307488
--- /dev/null
+++ b/drivers/qe/fdt.c
@@ -0,0 +1,90 @@
+/*
+ * Copyright 2008 Freescale Semiconductor, Inc.
+ *
+ * (C) Copyright 2000
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <libfdt.h>
+#include <fdt_support.h>
+#include "qe.h"
+
+DECLARE_GLOBAL_DATA_PTR;
+
+/*
+ * If a QE firmware has been uploaded, then add the 'firmware' node under
+ * the 'qe' node.
+ */
+void fdt_fixup_qe_firmware(void *blob)
+{
+ struct qe_firmware_info *qe_fw_info;
+ int node, ret;
+
+ qe_fw_info = qe_get_firmware_info();
+ if (!qe_fw_info)
+ return;
+
+ node = fdt_path_offset(blob, "/qe");
+ if (node < 0)
+ return;
+
+ /* We assume the node doesn't exist yet */
+ node = fdt_add_subnode(blob, node, "firmware");
+ if (node < 0)
+ return;
+
+ ret = fdt_setprop(blob, node, "extended-modes",
+ &qe_fw_info->extended_modes, sizeof(u64));
+ if (ret < 0)
+ goto error;
+
+ ret = fdt_setprop_string(blob, node, "id", qe_fw_info->id);
+ if (ret < 0)
+ goto error;
+
+ ret = fdt_setprop(blob, node, "virtual-traps", qe_fw_info->vtraps,
+ sizeof(qe_fw_info->vtraps));
+ if (ret < 0)
+ goto error;
+
+ return;
+
+error:
+ fdt_del_node(blob, node);
+}
+
+void ft_qe_setup(void *blob)
+{
+#ifdef CONFIG_QE
+ do_fixup_by_prop_u32(blob, "device_type", "qe", 4,
+ "bus-frequency", gd->qe_clk, 1);
+ do_fixup_by_prop_u32(blob, "device_type", "qe", 4,
+ "brg-frequency", gd->brg_clk, 1);
+ do_fixup_by_compat_u32(blob, "fsl,qe",
+ "clock-frequency", gd->qe_clk, 1);
+ do_fixup_by_compat_u32(blob, "fsl,qe",
+ "bus-frequency", gd->qe_clk, 1);
+ do_fixup_by_compat_u32(blob, "fsl,qe",
+ "brg-frequency", gd->brg_clk, 1);
+ fdt_fixup_qe_firmware(blob);
+#endif
+}
diff --git a/drivers/qe/qe.h b/drivers/qe/qe.h
index 4c96c67..741ed7f 100644
--- a/drivers/qe/qe.h
+++ b/drivers/qe/qe.h
@@ -289,5 +289,6 @@
int qe_set_mii_clk_src(int ucc_num);
int qe_upload_firmware(const struct qe_firmware *firmware);
struct qe_firmware_info *qe_get_firmware_info(void);
+void ft_qe_setup(void *blob);
#endif /* __QE_H__ */
diff --git a/drivers/serial/ns16550.c b/drivers/serial/ns16550.c
index 2429464..6b3f60e 100644
--- a/drivers/serial/ns16550.c
+++ b/drivers/serial/ns16550.c
@@ -21,11 +21,15 @@
com_port->mdr1 = 0x7; /* mode select reset TL16C750*/
#endif
com_port->lcr = LCR_BKSE | LCRVAL;
- com_port->dll = baud_divisor & 0xff;
- com_port->dlm = (baud_divisor >> 8) & 0xff;
+ com_port->dll = 0;
+ com_port->dlm = 0;
com_port->lcr = LCRVAL;
com_port->mcr = MCRVAL;
com_port->fcr = FCRVAL;
+ com_port->lcr = LCR_BKSE | LCRVAL;
+ com_port->dll = baud_divisor & 0xff;
+ com_port->dlm = (baud_divisor >> 8) & 0xff;
+ com_port->lcr = LCRVAL;
#if defined(CONFIG_OMAP)
#if defined(CONFIG_APTIX)
com_port->mdr1 = 3; /* /13 mode so Aptix 6MHz can hit 115200 */
@@ -38,12 +42,16 @@
void NS16550_reinit (NS16550_t com_port, int baud_divisor)
{
com_port->ier = 0x00;
+ com_port->lcr = LCR_BKSE | LCRVAL;
+ com_port->dll = 0;
+ com_port->dlm = 0;
+ com_port->lcr = LCRVAL;
+ com_port->mcr = MCRVAL;
+ com_port->fcr = FCRVAL;
com_port->lcr = LCR_BKSE;
com_port->dll = baud_divisor & 0xff;
com_port->dlm = (baud_divisor >> 8) & 0xff;
com_port->lcr = LCRVAL;
- com_port->mcr = MCRVAL;
- com_port->fcr = FCRVAL;
}
void NS16550_putc (NS16550_t com_port, char c)
diff --git a/include/asm-arm/arch-pxa/mmc.h b/include/asm-arm/arch-pxa/mmc.h
index a62679a..b9304b1 100644
--- a/include/asm-arm/arch-pxa/mmc.h
+++ b/include/asm-arm/arch-pxa/mmc.h
@@ -54,14 +54,17 @@
#define MMC_SPI_CRC_ON (0x01UL << 1)
/* MMC_CMDAT */
+#define MMC_CMDAT_SD_4DAT (0x0001UL << 8)
#define MMC_CMDAT_MMC_DMA_EN (0x0001UL << 7)
#define MMC_CMDAT_INIT (0x0001UL << 6)
#define MMC_CMDAT_BUSY (0x0001UL << 5)
+#define MMC_CMDAT_BCR (0x0003UL << 5)
#define MMC_CMDAT_STREAM (0x0001UL << 4)
#define MMC_CMDAT_BLOCK (0x0000UL << 4)
#define MMC_CMDAT_WRITE (0x0001UL << 3)
#define MMC_CMDAT_READ (0x0000UL << 3)
#define MMC_CMDAT_DATA_EN (0x0001UL << 2)
+#define MMC_CMDAT_R0 (0)
#define MMC_CMDAT_R1 (0x0001UL)
#define MMC_CMDAT_R2 (0x0002UL)
#define MMC_CMDAT_R3 (0x0003UL)
@@ -111,6 +114,7 @@
#define MMC_CMD_SEND_OP_COND 1
#define MMC_CMD_ALL_SEND_CID 2
#define MMC_CMD_SET_RCA 3
+#define MMC_CMD_SELECT_CARD 7
#define MMC_CMD_SEND_CSD 9
#define MMC_CMD_SEND_CID 10
#define MMC_CMD_SEND_STATUS 13
@@ -118,6 +122,10 @@
#define MMC_CMD_READ_BLOCK 17
#define MMC_CMD_RD_BLK_MULTI 18
#define MMC_CMD_WRITE_BLOCK 24
+#define MMC_CMD_APP_CMD 55
+
+#define SD_CMD_APP_SET_BUS_WIDTH 6
+#define SD_CMD_APP_OP_COND 41
#define MMC_MAX_BLOCK_SIZE 512
@@ -158,42 +166,41 @@
typedef struct mmc_csd
{
- uchar ecc:2,
- file_format:2,
- tmp_write_protect:1,
- perm_write_protect:1,
- copy:1,
- file_format_grp:1;
- uint64_t content_prot_app:1,
- rsvd3:4,
- write_bl_partial:1,
- write_bl_len:4,
- r2w_factor:3,
- default_ecc:2,
- wp_grp_enable:1,
- wp_grp_size:5,
- erase_grp_mult:5,
- erase_grp_size:5,
- c_size_mult1:3,
- vdd_w_curr_max:3,
- vdd_w_curr_min:3,
- vdd_r_curr_max:3,
- vdd_r_curr_min:3,
- c_size:12,
- rsvd2:2,
- dsr_imp:1,
- read_blk_misalign:1,
- write_blk_misalign:1,
- read_bl_partial:1;
-
- ushort read_bl_len:4,
- ccc:12;
- uchar tran_speed;
- uchar nsac;
- uchar taac;
- uchar rsvd1:2,
- spec_vers:4,
- csd_structure:2;
+ uint8_t csd_structure:2,
+ spec_ver:4,
+ rsvd1:2;
+ uint8_t taac;
+ uint8_t nsac;
+ uint8_t tran_speed;
+ uint16_t ccc:12,
+ read_bl_len:4;
+ uint64_t read_bl_partial:1,
+ write_blk_misalign:1,
+ read_blk_misalign:1,
+ dsr_imp:1,
+ rsvd2:2,
+ c_size:12,
+ vdd_r_curr_min:3,
+ vdd_r_curr_max:3,
+ vdd_w_curr_min:3,
+ vdd_w_curr_max:3,
+ c_size_mult:3,
+ erase_blk_en:1,
+ sector_size:7,
+ wp_grp_size:7,
+ wp_grp_enable:1,
+ default_ecc:2,
+ r2w_factor:3,
+ write_bl_len:4,
+ write_bl_partial:1,
+ rsvd3:4,
+ content_prot_app:1;
+ uint8_t file_format_grp:1,
+ copy:1,
+ perm_write_protect:1,
+ tmp_write_protect:1,
+ file_format:2,
+ ecc:2;
} mmc_csd_t;
diff --git a/include/asm-arm/arch-pxa/pxa-regs.h b/include/asm-arm/arch-pxa/pxa-regs.h
index 9b4da3a..e014568 100644
--- a/include/asm-arm/arch-pxa/pxa-regs.h
+++ b/include/asm-arm/arch-pxa/pxa-regs.h
@@ -1288,15 +1288,15 @@
#define _GEDR(x) __REG2(0x40E00048, ((x) & 0x60) >> 3)
#define _GAFR(x) __REG2(0x40E00054, ((x) & 0x70) >> 2)
-#define GPLR(x) __REG2(0x40E00000 + (((x) & 0x7f) < 96) ? 0:0x100, ((x) & 0x60) >> 3)
-#define GPDR(x) __REG2(0x40E0000C + (((x) & 0x7f) < 96) ? 0:0x100, ((x) & 0x60) >> 3)
-#define GPSR(x) __REG2(0x40E00018 + (((x) & 0x7f) < 96) ? 0:0x100, ((x) & 0x60) >> 3)
-#define GPCR(x) __REG2(0x40E00024 + (((x) & 0x7f) < 96) ? 0:0x100, ((x) & 0x60) >> 3)
-#define GRER(x) __REG2(0x40E00030 + (((x) & 0x7f) < 96) ? 0:0x100, ((x) & 0x60) >> 3)
-#define GFER(x) __REG2(0x40E0003C + (((x) & 0x7f) < 96) ? 0:0x100, ((x) & 0x60) >> 3)
-#define GEDR(x) __REG2(0x40E00048 + (((x) & 0x7f) < 96) ? 0:0x100, ((x) & 0x60) >> 3)
-#define GAFR(x) __REG2((((x) & 0x7f) < 96) ? 0x40E00054 : \
- ((((x) & 0x7f) < 112) ? 0x40E0006C : 0x40E00070),((x) & 0x60) >> 3)
+#define GPLR(x) (*((((x) & 0x7f) < 96) ? &_GPLR(x) : &GPLR3))
+#define GPDR(x) (*((((x) & 0x7f) < 96) ? &_GPDR(x) : &GPDR3))
+#define GPSR(x) (*((((x) & 0x7f) < 96) ? &_GPSR(x) : &GPSR3))
+#define GPCR(x) (*((((x) & 0x7f) < 96) ? &_GPCR(x) : &GPCR3))
+#define GRER(x) (*((((x) & 0x7f) < 96) ? &_GRER(x) : &GRER3))
+#define GFER(x) (*((((x) & 0x7f) < 96) ? &_GFER(x) : &GFER3))
+#define GEDR(x) (*((((x) & 0x7f) < 96) ? &_GEDR(x) : &GEDR3))
+#define GAFR(x) (*((((x) & 0x7f) < 96) ? &_GAFR(x) : \
+ ((((x) & 0x7f) < 112) ? &GAFR3_L : &GAFR3_U)))
#else
#define GPLR(x) __REG2(0x40E00000, ((x) & 0x60) >> 3)
diff --git a/include/common.h b/include/common.h
index 54083f1..c4ee3e2 100644
--- a/include/common.h
+++ b/include/common.h
@@ -479,6 +479,8 @@
ulong get_PCI_freq (void);
#endif
#if defined(CONFIG_S3C2400) || defined(CONFIG_S3C2410) || defined(CONFIG_LH7A40X)
+void s3c2410_irq(void);
+#define ARM920_IRQ_CALLBACK s3c2410_irq
ulong get_FCLK (void);
ulong get_HCLK (void);
ulong get_PCLK (void);
diff --git a/include/configs/AP1000.h b/include/configs/AP1000.h
index d490b33..baa9741 100644
--- a/include/configs/AP1000.h
+++ b/include/configs/AP1000.h
@@ -22,8 +22,6 @@
* (easy to change)
*/
-#undef DEBUG
-
#define CONFIG_405 1 /* This is a PPC405 CPU */
#define CONFIG_4xx 1 /* ...member of PPC4xx family */
diff --git a/include/configs/BAB7xx.h b/include/configs/BAB7xx.h
index c11e9c9..8ec70aa 100644
--- a/include/configs/BAB7xx.h
+++ b/include/configs/BAB7xx.h
@@ -28,7 +28,6 @@
#ifndef __CONFIG_H
#define __CONFIG_H
-#undef DEBUG
#define GTREGREAD(x) 0xffffffff /* needed for debug */
/*
diff --git a/include/configs/EB+MCF-EV123.h b/include/configs/EB+MCF-EV123.h
index dae5295..ea49a5d 100644
--- a/include/configs/EB+MCF-EV123.h
+++ b/include/configs/EB+MCF-EV123.h
@@ -27,9 +27,7 @@
#define CONFIG_EB_MCF_EV123
-#undef DEBUG
#undef CFG_HALT_BEFOR_RAM_JUMP
-#undef ET_DEBUG
/*
* High Level Configuration Options (easy to change)
diff --git a/include/configs/ELPPC.h b/include/configs/ELPPC.h
index bb77188..c64537f 100644
--- a/include/configs/ELPPC.h
+++ b/include/configs/ELPPC.h
@@ -28,7 +28,6 @@
#ifndef __CONFIG_H
#define __CONFIG_H
-#undef DEBUG
#define GTREGREAD(x) 0xffffffff /* needed for debug */
/*
diff --git a/include/configs/IPHASE4539.h b/include/configs/IPHASE4539.h
index 6fee455..bb2c96a 100644
--- a/include/configs/IPHASE4539.h
+++ b/include/configs/IPHASE4539.h
@@ -30,8 +30,6 @@
#ifndef __CONFIG_H
#define __CONFIG_H
-#undef DEBUG /* General debug */
-
/*-----------------------------------------------------------------------
* High Level Configuration Options
* (easy to change)
diff --git a/include/configs/M52277EVB.h b/include/configs/M52277EVB.h
index ab574d5..a3d7bc4 100644
--- a/include/configs/M52277EVB.h
+++ b/include/configs/M52277EVB.h
@@ -38,8 +38,6 @@
#define CONFIG_M52277 /* define processor type */
#define CONFIG_M52277EVB /* M52277EVB board */
-#undef DEBUG
-
#define CONFIG_MCFUART
#define CFG_UART_PORT (0)
#define CONFIG_BAUDRATE 115200
diff --git a/include/configs/M5235EVB.h b/include/configs/M5235EVB.h
index 7f544c8..3b4bff3 100644
--- a/include/configs/M5235EVB.h
+++ b/include/configs/M5235EVB.h
@@ -37,8 +37,6 @@
#define CONFIG_MCF523x /* define processor family */
#define CONFIG_M5235 /* define processor type */
-#undef DEBUG
-
#define CONFIG_MCFUART
#define CFG_UART_PORT (0)
#define CONFIG_BAUDRATE 115200
diff --git a/include/configs/M5271EVB.h b/include/configs/M5271EVB.h
index 798ec0c..47e1e03 100644
--- a/include/configs/M5271EVB.h
+++ b/include/configs/M5271EVB.h
@@ -31,8 +31,6 @@
#ifndef _M5271EVB_H
#define _M5271EVB_H
-#undef DEBUG
-
/*
* High Level Configuration Options (easy to change)
*/
diff --git a/include/configs/M5329EVB.h b/include/configs/M5329EVB.h
index e956739..1a15c77 100644
--- a/include/configs/M5329EVB.h
+++ b/include/configs/M5329EVB.h
@@ -37,8 +37,6 @@
#define CONFIG_MCF532x /* define processor family */
#define CONFIG_M5329 /* define processor type */
-#undef DEBUG
-
#define CONFIG_MCFUART
#define CFG_UART_PORT (0)
#define CONFIG_BAUDRATE 115200
diff --git a/include/configs/M5373EVB.h b/include/configs/M5373EVB.h
index 6bfffa1..da4156c 100644
--- a/include/configs/M5373EVB.h
+++ b/include/configs/M5373EVB.h
@@ -37,8 +37,6 @@
#define CONFIG_MCF532x /* define processor family */
#define CONFIG_M5373 /* define processor type */
-#undef DEBUG
-
#define CONFIG_MCFUART
#define CFG_UART_PORT (0)
#define CONFIG_BAUDRATE 115200
diff --git a/include/configs/M54455EVB.h b/include/configs/M54455EVB.h
index 581c794..5f55761 100644
--- a/include/configs/M54455EVB.h
+++ b/include/configs/M54455EVB.h
@@ -38,8 +38,6 @@
#define CONFIG_M54455 /* define processor type */
#define CONFIG_M54455EVB /* M54455EVB board */
-#undef DEBUG
-
#define CONFIG_MCFUART
#define CFG_UART_PORT (0)
#define CONFIG_BAUDRATE 115200
diff --git a/include/configs/M5475EVB.h b/include/configs/M5475EVB.h
index 84c2105..f0d42be 100644
--- a/include/configs/M5475EVB.h
+++ b/include/configs/M5475EVB.h
@@ -38,8 +38,6 @@
#define CONFIG_M547x /* define processor type */
#define CONFIG_M5475 /* define processor type */
-#undef DEBUG
-
#define CONFIG_MCFUART
#define CFG_UART_PORT (0)
#define CONFIG_BAUDRATE 115200
diff --git a/include/configs/M5485EVB.h b/include/configs/M5485EVB.h
index e9e5ee9..88dd219 100644
--- a/include/configs/M5485EVB.h
+++ b/include/configs/M5485EVB.h
@@ -38,8 +38,6 @@
#define CONFIG_M548x /* define processor type */
#define CONFIG_M5485 /* define processor type */
-#undef DEBUG
-
#define CONFIG_MCFUART
#define CFG_UART_PORT (0)
#define CONFIG_BAUDRATE 115200
diff --git a/include/configs/MPC8315ERDB.h b/include/configs/MPC8315ERDB.h
index ad2305c..ff7101f 100644
--- a/include/configs/MPC8315ERDB.h
+++ b/include/configs/MPC8315ERDB.h
@@ -25,8 +25,6 @@
#ifndef __CONFIG_H
#define __CONFIG_H
-#undef DEBUG
-
/*
* High Level Configuration Options
*/
diff --git a/include/configs/MPC8323ERDB.h b/include/configs/MPC8323ERDB.h
index 295e785..bf5ef4b 100644
--- a/include/configs/MPC8323ERDB.h
+++ b/include/configs/MPC8323ERDB.h
@@ -9,8 +9,6 @@
#ifndef __CONFIG_H
#define __CONFIG_H
-#undef DEBUG
-
/*
* High Level Configuration Options
*/
diff --git a/include/configs/MPC832XEMDS.h b/include/configs/MPC832XEMDS.h
index 6c0e68a..702b073 100644
--- a/include/configs/MPC832XEMDS.h
+++ b/include/configs/MPC832XEMDS.h
@@ -20,8 +20,6 @@
#ifndef __CONFIG_H
#define __CONFIG_H
-#undef DEBUG
-
/*
* High Level Configuration Options
*/
diff --git a/include/configs/MPC8349EMDS.h b/include/configs/MPC8349EMDS.h
index bb90c2d..331f4c9 100644
--- a/include/configs/MPC8349EMDS.h
+++ b/include/configs/MPC8349EMDS.h
@@ -29,8 +29,6 @@
#ifndef __CONFIG_H
#define __CONFIG_H
-#undef DEBUG
-
/*
* High Level Configuration Options
*/
diff --git a/include/configs/MPC8360EMDS.h b/include/configs/MPC8360EMDS.h
index 168ca2a..eff9fba 100644
--- a/include/configs/MPC8360EMDS.h
+++ b/include/configs/MPC8360EMDS.h
@@ -22,8 +22,6 @@
#ifndef __CONFIG_H
#define __CONFIG_H
-#undef DEBUG
-
/*
* High Level Configuration Options
*/
diff --git a/include/configs/MPC8360ERDK.h b/include/configs/MPC8360ERDK.h
index 83a4b1e..27b037a 100644
--- a/include/configs/MPC8360ERDK.h
+++ b/include/configs/MPC8360ERDK.h
@@ -17,8 +17,6 @@
#ifndef __CONFIG_H
#define __CONFIG_H
-#undef DEBUG
-
/*
* High Level Configuration Options
*/
diff --git a/include/configs/MPC837XEMDS.h b/include/configs/MPC837XEMDS.h
index 2b84e9c..61de084 100644
--- a/include/configs/MPC837XEMDS.h
+++ b/include/configs/MPC837XEMDS.h
@@ -21,8 +21,6 @@
#ifndef __CONFIG_H
#define __CONFIG_H
-#undef DEBUG
-
/*
* High Level Configuration Options
*/
diff --git a/include/configs/MPC8540EVAL.h b/include/configs/MPC8540EVAL.h
index bf64f27..174215c 100644
--- a/include/configs/MPC8540EVAL.h
+++ b/include/configs/MPC8540EVAL.h
@@ -240,8 +240,6 @@
#define INTEL_LXT971_PHY 1
#endif
-#undef DEBUG
-
/* Environment */
#ifndef CFG_RAMBOOT
#if defined(CONFIG_RAM_AS_FLASH)
diff --git a/include/configs/MVBLUE.h b/include/configs/MVBLUE.h
index 0defafe..d799f54 100644
--- a/include/configs/MVBLUE.h
+++ b/include/configs/MVBLUE.h
@@ -53,8 +53,6 @@
#define ERR_LED(code)
#endif
-#undef DEBUG
-
#define CONFIG_MPC824X 1
#define CONFIG_MPC8245 1
#define CONFIG_MVBLUE 1
diff --git a/include/configs/QS823.h b/include/configs/QS823.h
index 3657fea..3dd84e8 100644
--- a/include/configs/QS823.h
+++ b/include/configs/QS823.h
@@ -38,7 +38,6 @@
#undef CFG_DEVICE_NULLDEV /* null device */
#undef CONFIG_SILENT_CONSOLE /* silent console */
#undef CFG_CONSOLE_INFO_QUIET /* silent console ? */
-#undef DEBUG /* debug output code */
#undef DEBUG_FLASH /* debug flash code */
#undef FLASH_DEBUG /* debug fash code */
#undef DEBUG_ENV /* debug environment code */
diff --git a/include/configs/QS850.h b/include/configs/QS850.h
index 3db539f..7dd6eca 100644
--- a/include/configs/QS850.h
+++ b/include/configs/QS850.h
@@ -38,7 +38,6 @@
#undef CFG_DEVICE_NULLDEV /* null device */
#undef CONFIG_SILENT_CONSOLE /* silent console */
#undef CFG_CONSOLE_INFO_QUIET /* silent console ? */
-#undef DEBUG /* debug output code */
#undef DEBUG_FLASH /* debug flash code */
#undef FLASH_DEBUG /* debug fash code */
#undef DEBUG_ENV /* debug environment code */
diff --git a/include/configs/QS860T.h b/include/configs/QS860T.h
index b3442de..62cf2a4 100644
--- a/include/configs/QS860T.h
+++ b/include/configs/QS860T.h
@@ -38,7 +38,6 @@
#undef CFG_DEVICE_NULLDEV /* null device */
#undef CONFIG_SILENT_CONSOLE /* silent console */
#undef CFG_CONSOLE_INFO_QUIET /* silent console ? */
-#undef DEBUG /* debug output code */
#undef DEBUG_FLASH /* debug flash code */
#undef FLASH_DEBUG /* debug fash code */
#undef DEBUG_ENV /* debug environment code */
diff --git a/include/configs/Rattler.h b/include/configs/Rattler.h
index d7652fa..428c0c2 100644
--- a/include/configs/Rattler.h
+++ b/include/configs/Rattler.h
@@ -37,8 +37,6 @@
#define CONFIG_RATTLER /* Analogue&Micro Rattler board */
-#undef DEBUG
-
/* Allow serial number (serial#) and MAC address (ethaddr) to be overwritten */
#define CONFIG_ENV_OVERWRITE
diff --git a/include/configs/ads5121.h b/include/configs/ads5121.h
index ce458ae5..09c3140 100644
--- a/include/configs/ads5121.h
+++ b/include/configs/ads5121.h
@@ -27,9 +27,6 @@
#ifndef __CONFIG_H
#define __CONFIG_H
-#define DEBUG
-#undef DEBUG
-
/*
* Memory map for the ADS5121 board:
*
@@ -109,25 +106,22 @@
* [04:00] DRAM tRPA
*/
-#define CFG_MDDRC_SYS_CFG 0xF8604200
-#define CFG_MDDRC_SYS_CFG_RUN 0xE8604200
-#define CFG_MDDRC_SYS_CFG_EN 0x30000000
-#define CFG_MDDRC_TIME_CFG0 0x0000281E
-#define CFG_MDDRC_TIME_CFG0_RUN 0x01F4281E
+#define CFG_MDDRC_SYS_CFG 0xF8604A00
+#define CFG_MDDRC_SYS_CFG_RUN 0xE8604A00
+#define CFG_MDDRC_SYS_CFG_EN 0xF0000000
+#define CFG_MDDRC_TIME_CFG0 0x00003D2E
+#define CFG_MDDRC_TIME_CFG0_RUN 0x06183D2E
#define CFG_MDDRC_TIME_CFG1 0x54EC1168
#define CFG_MDDRC_TIME_CFG2 0x35210864
#define CFG_MICRON_NOP 0x01380000
#define CFG_MICRON_PCHG_ALL 0x01100400
-#define CFG_MICRON_MR 0x01000022
#define CFG_MICRON_EM2 0x01020000
#define CFG_MICRON_EM3 0x01030000
#define CFG_MICRON_EN_DLL 0x01010000
-#define CFG_MICRON_RST_DLL 0x01000932
#define CFG_MICRON_RFSH 0x01080000
-#define CFG_MICRON_INIT_DEV_OP 0x01000832
+#define CFG_MICRON_INIT_DEV_OP 0x01000432
#define CFG_MICRON_OCD_DEFAULT 0x01010780
-#define CFG_MICRON_OCD_EXIT 0x01010400
/* DDR Priority Manager Configuration */
#define CFG_MDDRCGRP_PM_CFG1 0x000777AA
@@ -415,8 +409,9 @@
#define CONFIG_OF_BOARD_SETUP 1
#define OF_CPU "PowerPC,5121@0"
-#define OF_SOC "soc5121@80000000"
+#define OF_SOC "soc@80000000"
+#define OF_SOC_OLD "soc5121@80000000"
#define OF_TBCLK (bd->bi_busfreq / 4)
-#define OF_STDOUT_PATH "/soc5121@80000000/serial@11300"
+#define OF_STDOUT_PATH "/soc@80000000/serial@11300"
#endif /* __CONFIG_H */
diff --git a/include/configs/assabet.h b/include/configs/assabet.h
index 226ad54..d10f092 100644
--- a/include/configs/assabet.h
+++ b/include/configs/assabet.h
@@ -29,8 +29,6 @@
#ifndef __CONFIG_H
#define __CONFIG_H
-#undef DEBUG
-
/*
* High Level Configuration Options
* (easy to change)
diff --git a/include/configs/at91rm9200dk.h b/include/configs/at91rm9200dk.h
index a65c5f3..5b7212a 100644
--- a/include/configs/at91rm9200dk.h
+++ b/include/configs/at91rm9200dk.h
@@ -170,8 +170,8 @@
#define CONFIG_HAS_DATAFLASH 1
#define CFG_SPI_WRITE_TOUT (5*CFG_HZ)
-#define CFG_MAX_DATAFLASH_BANKS 2
-#define CFG_MAX_DATAFLASH_PAGES 16384
+#define CFG_MAX_DATAFLASH_BANKS 2
+#define CFG_MAX_DATAFLASH_PAGES 16384
#define CFG_DATAFLASH_LOGIC_ADDR_CS0 0xC0000000 /* Logical adress for CS0 */
#define CFG_DATAFLASH_LOGIC_ADDR_CS3 0xD0000000 /* Logical adress for CS3 */
@@ -192,11 +192,11 @@
#else
#define CFG_ENV_IS_IN_FLASH 1
#ifdef CONFIG_SKIP_LOWLEVEL_INIT
-#define CFG_ENV_ADDR (PHYS_FLASH_1 + 0x60000) /* after u-boot.bin */
-#define CFG_ENV_SIZE 0x10000 /* sectors are 64K here */
-#else
#define CFG_ENV_ADDR (PHYS_FLASH_1 + 0xe000) /* between boot.bin and u-boot.bin.gz */
#define CFG_ENV_SIZE 0x2000 /* 0x8000 */
+#else
+#define CFG_ENV_ADDR (PHYS_FLASH_1 + 0x60000) /* after u-boot.bin */
+#define CFG_ENV_SIZE 0x10000 /* sectors are 64K here */
#endif /* CONFIG_SKIP_LOWLEVEL_INIT */
#endif /* CFG_ENV_IS_IN_DATAFLASH */
@@ -204,44 +204,25 @@
#define CFG_LOAD_ADDR 0x21000000 /* default load address */
#ifdef CONFIG_SKIP_LOWLEVEL_INIT
-#define CFG_BOOT_SIZE 0x00 /* 0 KBytes */
-#define CFG_U_BOOT_BASE PHYS_FLASH_1
-#define CFG_U_BOOT_SIZE 0x60000 /* 384 KBytes */
-#else
#define CFG_BOOT_SIZE 0x6000 /* 24 KBytes */
#define CFG_U_BOOT_BASE (PHYS_FLASH_1 + 0x10000)
#define CFG_U_BOOT_SIZE 0x10000 /* 64 KBytes */
+#else
+#define CFG_BOOT_SIZE 0x00 /* 0 KBytes */
+#define CFG_U_BOOT_BASE PHYS_FLASH_1
+#define CFG_U_BOOT_SIZE 0x60000 /* 384 KBytes */
#endif /* CONFIG_SKIP_LOWLEVEL_INIT */
-#define CFG_BAUDRATE_TABLE {115200 , 19200, 38400, 57600, 9600 }
+#define CFG_BAUDRATE_TABLE { 115200, 19200, 38400, 57600, 9600 }
#define CFG_PROMPT "U-Boot> " /* Monitor Command Prompt */
#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
#define CFG_MAXARGS 16 /* max number of command args */
#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
-#ifndef __ASSEMBLY__
-/*-----------------------------------------------------------------------
- * Board specific extension for bd_info
- *
- * This structure is embedded in the global bd_info (bd_t) structure
- * and can be used by the board specific code (eg board/...)
- */
-
-struct bd_info_ext {
- /* helper variable for board environment handling
- *
- * env_crc_valid == 0 => uninitialised
- * env_crc_valid > 0 => environment crc in flash is valid
- * env_crc_valid < 0 => environment crc in flash is invalid
- */
- int env_crc_valid;
-};
-#endif
-
#define CFG_HZ 1000
#define CFG_HZ_CLOCK AT91C_MASTER_CLOCK/2 /* AT91C_TC0_CMR is implicitly set to */
- /* AT91C_TC_TIMER_DIV1_CLOCK */
+ /* AT91C_TC_TIMER_DIV1_CLOCK */
#define CONFIG_STACKSIZE (32*1024) /* regular stack */
diff --git a/include/configs/cmc_pu2.h b/include/configs/cmc_pu2.h
index f32c8c2..d22d350 100644
--- a/include/configs/cmc_pu2.h
+++ b/include/configs/cmc_pu2.h
@@ -148,7 +148,7 @@
#define CONFIG_NR_DRAM_BANKS 1
#define PHYS_SDRAM 0x20000000
-#define PHYS_SDRAM_SIZE 0x1000000 /* 16 megs */
+#define PHYS_SDRAM_SIZE 0x1000000 /* 16 megs */
#define CFG_MEMTEST_START PHYS_SDRAM
#define CFG_MEMTEST_END CFG_MEMTEST_START + PHYS_SDRAM_SIZE - 262144
@@ -186,25 +186,6 @@
#define CFG_MAXARGS 32 /* max number of command args */
#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
-#ifndef __ASSEMBLY__
-/*-----------------------------------------------------------------------
- * Board specific extension for bd_info
- *
- * This structure is embedded in the global bd_info (bd_t) structure
- * and can be used by the board specific code (eg board/...)
- */
-
-struct bd_info_ext {
- /* helper variable for board environment handling
- *
- * env_crc_valid == 0 => uninitialised
- * env_crc_valid > 0 => environment crc in flash is valid
- * env_crc_valid < 0 => environment crc in flash is invalid
- */
- int env_crc_valid;
-};
-#endif /* __ASSEMBLY__ */
-
#define CFG_HZ 1000
#define CFG_HZ_CLOCK (AT91C_MASTER_CLOCK/2) /* AT91C_TC0_CMR is implicitly set to */
/* AT91C_TC_TIMER_DIV1_CLOCK */
diff --git a/include/configs/csb637.h b/include/configs/csb637.h
index 976dae3..f93c3bc 100644
--- a/include/configs/csb637.h
+++ b/include/configs/csb637.h
@@ -170,8 +170,8 @@
#undef CONFIG_HAS_DATAFLASH
#define CFG_SPI_WRITE_TOUT (5*CFG_HZ)
-#define CFG_MAX_DATAFLASH_BANKS 0
-#define CFG_MAX_DATAFLASH_PAGES 16384
+#define CFG_MAX_DATAFLASH_BANKS 0
+#define CFG_MAX_DATAFLASH_PAGES 16384
#define CFG_DATAFLASH_LOGIC_ADDR_CS0 0xC0000000 /* Logical adress for CS0 */
#define CFG_DATAFLASH_LOGIC_ADDR_CS3 0xD0000000 /* Logical adress for CS3 */
@@ -209,35 +209,16 @@
#define CFG_LOAD_ADDR 0x21000000 /* default load address */
-#define CFG_BAUDRATE_TABLE {115200, 57600, 38400, 19200, 9600 }
+#define CFG_BAUDRATE_TABLE { 115200, 57600, 38400, 19200, 9600 }
#define CFG_PROMPT "U-Boot> " /* Monitor Command Prompt */
#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
#define CFG_MAXARGS 16 /* max number of command args */
#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
-#ifndef __ASSEMBLY__
-/*-----------------------------------------------------------------------
- * Board specific extension for bd_info
- *
- * This structure is embedded in the global bd_info (bd_t) structure
- * and can be used by the board specific code (eg board/...)
- */
-
-struct bd_info_ext {
- /* helper variable for board environment handling
- *
- * env_crc_valid == 0 => uninitialised
- * env_crc_valid > 0 => environment crc in flash is valid
- * env_crc_valid < 0 => environment crc in flash is invalid
- */
- int env_crc_valid;
-};
-#endif
-
#define CFG_HZ 1000
#define CFG_HZ_CLOCK AT91C_MASTER_CLOCK/2 /* AT91C_TC0_CMR is implicitly set to */
- /* AT91C_TC_TIMER_DIV1_CLOCK */
+ /* AT91C_TC_TIMER_DIV1_CLOCK */
#define CONFIG_STACKSIZE (32*1024) /* regular stack */
diff --git a/include/configs/ep8248.h b/include/configs/ep8248.h
index 85ad70a..cebe849 100644
--- a/include/configs/ep8248.h
+++ b/include/configs/ep8248.h
@@ -31,8 +31,6 @@
#define CONFIG_EP8248 /* Embedded Planet EP8248 board */
-#undef DEBUG
-
#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */
/* Allow serial number (serial#) and MAC address (ethaddr) to be overwritten */
diff --git a/include/configs/ep82xxm.h b/include/configs/ep82xxm.h
index 4febd32..8e5d6e5 100644
--- a/include/configs/ep82xxm.h
+++ b/include/configs/ep82xxm.h
@@ -31,8 +31,6 @@
#define CONFIG_EP82XXM /* Embedded Planet EP82xxM H 1.0 board */
/* 256MB SDRAM / 64MB FLASH */
-#undef DEBUG
-
#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */
/* Allow serial number (serial#) and MAC address (ethaddr) to be overwritten */
diff --git a/include/configs/gcplus.h b/include/configs/gcplus.h
index e11ce4c..3b1b4ab 100644
--- a/include/configs/gcplus.h
+++ b/include/configs/gcplus.h
@@ -29,8 +29,6 @@
#ifndef __CONFIG_H
#define __CONFIG_H
-#undef DEBUG
-
/*
* The ADS GCPlus Linux boot ROM loads U-Boot into RAM at 0xc0200000.
* We don't actually init RAM in this case since we're using U-Boot as
diff --git a/include/configs/gw8260.h b/include/configs/gw8260.h
index ff57240..7c2c224 100644
--- a/include/configs/gw8260.h
+++ b/include/configs/gw8260.h
@@ -51,7 +51,6 @@
#define __CONFIG_H
/* Enable debug prints */
-#undef DEBUG /* General debug */
#undef DEBUG_BOOTP_EXT /* Debug received vendor fields */
/* What is the oscillator's (UX2) frequency in Hz? */
diff --git a/include/configs/mgcoge.h b/include/configs/mgcoge.h
index 3de2466..f4a1cc0 100644
--- a/include/configs/mgcoge.h
+++ b/include/configs/mgcoge.h
@@ -35,8 +35,6 @@
#define CONFIG_CPM2 1 /* Has a CPM2 */
-#undef DEBUG
-
/*
* Select serial console configuration
*
diff --git a/include/configs/mp2usb.h b/include/configs/mp2usb.h
index ea5a44b..294221f 100644
--- a/include/configs/mp2usb.h
+++ b/include/configs/mp2usb.h
@@ -47,7 +47,7 @@
#define CFG_ATMEL_PLL_INIT_BUG 1
#ifndef CONFIG_SKIP_LOWLEVEL_INIT
-#define CFG_USE_MAIN_OSCILLATOR 1
+#define CFG_USE_MAIN_OSCILLATOR 1
/* flash */
#define MC_PUIA_VAL 0x00000000
#define MC_PUP_VAL 0x00000000
@@ -216,25 +216,6 @@
#define CFG_DEVICE_DEREGISTER /* needs device_deregister */
#define LITTLEENDIAN 1 /* used by usb_ohci.c */
-#ifndef __ASSEMBLY__
-/*-----------------------------------------------------------------------
- * Board specific extension for bd_info
- *
- * This structure is embedded in the global bd_info (bd_t) structure
- * and can be used by the board specific code (eg board/...)
- */
-
-struct bd_info_ext {
- /* helper variable for board environment handling
- *
- * env_crc_valid == 0 => uninitialised
- * env_crc_valid > 0 => environment crc in flash is valid
- * env_crc_valid < 0 => environment crc in flash is invalid
- */
- int env_crc_valid;
-};
-#endif /* __ASSEMBLY__ */
-
#define CFG_HZ 1000
#define CFG_HZ_CLOCK (AT91C_MASTER_CLOCK/2) /* AT91C_TC0_CMR is implicitly set to */
/* AT91C_TC_TIMER_DIV1_CLOCK */
diff --git a/include/configs/mpc7448hpc2.h b/include/configs/mpc7448hpc2.h
index bd3107a..c7216c9 100644
--- a/include/configs/mpc7448hpc2.h
+++ b/include/configs/mpc7448hpc2.h
@@ -33,8 +33,6 @@
#ifndef __CONFIG_H
#define __CONFIG_H
-#undef DEBUG
-
/* Board Configuration Definitions */
/* MPC7448HPC2 (High-Performance Computing II) (Taiga) board */
diff --git a/include/configs/ms7720se.h b/include/configs/ms7720se.h
index 7035002..9c94c4e 100644
--- a/include/configs/ms7720se.h
+++ b/include/configs/ms7720se.h
@@ -25,7 +25,6 @@
#ifndef __MS7720SE_H
#define __MS7720SE_H
-#undef DEBUG
#define CONFIG_SH 1
#define CONFIG_SH3 1
#define CONFIG_CPU_SH7720 1
diff --git a/include/configs/ms7722se.h b/include/configs/ms7722se.h
index ae0d018..8538037 100644
--- a/include/configs/ms7722se.h
+++ b/include/configs/ms7722se.h
@@ -25,7 +25,6 @@
#ifndef __MS7722SE_H
#define __MS7722SE_H
-#undef DEBUG
#define CONFIG_SH 1
#define CONFIG_SH4 1
#define CONFIG_CPU_SH7722 1
diff --git a/include/configs/ms7750se.h b/include/configs/ms7750se.h
index 3668156..a25364d 100644
--- a/include/configs/ms7750se.h
+++ b/include/configs/ms7750se.h
@@ -25,7 +25,6 @@
#ifndef __MS7750SE_H
#define __MS7750SE_H
-#undef DEBUG
#define CONFIG_SH 1
#define CONFIG_SH4 1
#define CONFIG_CPU_SH7750 1
diff --git a/include/configs/ppmc7xx.h b/include/configs/ppmc7xx.h
index fe7de7b..1d2d38b 100644
--- a/include/configs/ppmc7xx.h
+++ b/include/configs/ppmc7xx.h
@@ -30,7 +30,6 @@
* do_bdinfo - Required to build with debug
*/
-#undef DEBUG
#ifdef DEBUG
#define GTREGREAD(x) 0xFFFFFFFF
#define do_bdinfo(a,b,c,d)
diff --git a/include/configs/qemu-mips.h b/include/configs/qemu-mips.h
index 33c8283..e164019 100644
--- a/include/configs/qemu-mips.h
+++ b/include/configs/qemu-mips.h
@@ -32,8 +32,6 @@
#define CONFIG_QEMU_MIPS 1
#define CONFIG_MISC_INIT_R
-#undef DEBUG
-
/*IP address is default used by Qemu*/
#define CONFIG_IPADDR 10.0.2.15 /* Our IP address */
#define CONFIG_SERVERIP 10.0.2.2 /* Server IP address*/
diff --git a/include/configs/sacsng.h b/include/configs/sacsng.h
index c474acd..ec7d34a 100644
--- a/include/configs/sacsng.h
+++ b/include/configs/sacsng.h
@@ -35,7 +35,6 @@
#ifndef __CONFIG_H
#define __CONFIG_H
-#undef DEBUG /* General debug */
#undef DEBUG_BOOTP_EXT /* Debug received vendor fields */
#undef CONFIG_LOGBUFFER /* External logbuffer support */
diff --git a/include/configs/sbc8260.h b/include/configs/sbc8260.h
index b1d41a6..6063398 100644
--- a/include/configs/sbc8260.h
+++ b/include/configs/sbc8260.h
@@ -36,7 +36,6 @@
#define __CONFIG_H
/* Enable debug prints */
-#undef DEBUG /* General debug */
#undef DEBUG_BOOTP_EXT /* Debug received vendor fields */
/*****************************************************************************
diff --git a/include/configs/sbc8349.h b/include/configs/sbc8349.h
index 4cc4ff1..2498b3e 100644
--- a/include/configs/sbc8349.h
+++ b/include/configs/sbc8349.h
@@ -31,8 +31,6 @@
#ifndef __CONFIG_H
#define __CONFIG_H
-#undef DEBUG
-
/*
* High Level Configuration Options
*/
diff --git a/include/configs/voiceblue.h b/include/configs/voiceblue.h
index 7cab31d..8c827af 100644
--- a/include/configs/voiceblue.h
+++ b/include/configs/voiceblue.h
@@ -26,10 +26,6 @@
#include <configs/omap1510.h>
-/*
- * High Level Configuration Options
- * (easy to change)
- */
#define CONFIG_ARM925T 1 /* This is an arm925t CPU */
#define CONFIG_OMAP 1 /* in a TI OMAP core */
#define CONFIG_OMAP1510 1 /* which is in a 5910 */
@@ -54,10 +50,9 @@
*/
#define CONFIG_NR_DRAM_BANKS 1 /* we have 1 bank of DRAM */
#define PHYS_SDRAM_1 0x10000000 /* SDRAM Bank #1 */
-#define PHYS_SDRAM_1_SIZE SZ_64M
+#define PHYS_SDRAM_1_SIZE (64 * 1024 * 1024)
#define PHYS_FLASH_1 0x00000000 /* Flash Bank #1 */
-#define PHYS_FLASH_2 0x0c000000
#define CFG_LOAD_ADDR PHYS_SDRAM_1 + 0x400000 /* default load address */
@@ -67,50 +62,34 @@
#define CFG_FLASH_CFI /* Flash is CFI conformant */
#define CFG_FLASH_CFI_DRIVER /* Use the common driver */
#define CFG_MAX_FLASH_BANKS 1
-#ifdef VOICEBLUE_SMALL_FLASH
-#define CFG_FLASH_BANKS_LIST { PHYS_FLASH_2 }
-#else
-#define CFG_FLASH_BANKS_LIST { PHYS_FLASH_1 }
-#endif
+#define CFG_FLASH_BASE PHYS_FLASH_1
/* FIXME: Does not work on AMD flash */
/* #define CFG_FLASH_USE_BUFFER_WRITE 1 */ /* use buffered writes (20x faster) */
#define CFG_MAX_FLASH_SECT 512 /* max # of sectors on one chip */
#define CFG_MONITOR_BASE PHYS_FLASH_1
-#define CFG_MONITOR_LEN SZ_128K
+#define CFG_MONITOR_LEN (256 * 1024)
/*
* Environment settings
*/
-#ifdef VOICEBLUE_SMALL_FLASH
-#define CFG_ENV_IS_NOWHERE
-#define CFG_ENV_SIZE SZ_1K
-#else
#define CFG_ENV_IS_IN_FLASH
#define CFG_ENV_ADDR (PHYS_FLASH_1 + CFG_MONITOR_LEN)
-#define CFG_ENV_SIZE SZ_8K
-#define CFG_ENV_SECT_SIZE SZ_64K
+#define CFG_ENV_SIZE (8 * 1024)
+#define CFG_ENV_SECT_SIZE (64 * 1024)
#define CFG_ENV_ADDR_REDUND (CFG_ENV_ADDR + CFG_ENV_SECT_SIZE)
#define CFG_ENV_SIZE_REDUND CFG_ENV_SIZE
#define CONFIG_ENV_OVERWRITE
-#endif
-
/*
* Size of malloc() pool and stack
*/
#define CFG_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */
-#ifdef VOICEBLUE_SMALL_FLASH
-#define CFG_MALLOC_LEN (SZ_64K - CFG_GBL_DATA_SIZE)
-#define CONFIG_STACKSIZE SZ_8K
-#define PHYS_SDRAM_1_RESERVED 0
-#else
-#define CFG_MALLOC_LEN SZ_4M
-#define CONFIG_STACKSIZE SZ_1M
+#define CFG_MALLOC_LEN (4 * 1024 * 1024)
+#define CONFIG_STACKSIZE (1 * 1024 * 1024)
#define PHYS_SDRAM_1_RESERVED (CFG_MONITOR_LEN + CFG_MALLOC_LEN + CONFIG_STACKSIZE)
-#endif
/*
* Hardware drivers
@@ -118,6 +97,14 @@
#define CONFIG_DRIVER_SMC91111
#define CONFIG_SMC91111_BASE 0x08000300
+#define CONFIG_HARD_I2C
+#define CFG_I2C_SPEED 100000
+#define CFG_I2C_SLAVE 1
+#define CONFIG_DRIVER_OMAP1510_I2C
+
+#define CONFIG_RTC_DS1307
+#define CFG_I2C_RTC_ADDR 0x68
+
/*
* NS16550 Configuration
*/
@@ -138,21 +125,18 @@
#include <config_cmd_default.h>
#define CONFIG_CMD_BDI
-#define CONFIG_CMD_LOADB
-#define CONFIG_CMD_IMI
-#define CONFIG_CMD_FLASH
-#define CONFIG_CMD_MEMORY
-#define CONFIG_CMD_NET
#define CONFIG_CMD_BOOTD
#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_ENV
+#define CONFIG_CMD_FLASH
+#define CONFIG_CMD_IMI
+#define CONFIG_CMD_JFFS2
+#define CONFIG_CMD_LOADB
+#define CONFIG_CMD_MEMORY
+#define CONFIG_CMD_NET
#define CONFIG_CMD_PING
#define CONFIG_CMD_RUN
-#if !defined(VOICEBLUE_SMALL_FLASH)
- #define CONFIG_CMD_ENV
- #define CONFIG_CMD_JFFS2
-#endif
-
/*
* BOOTP options
@@ -165,32 +149,20 @@
#define CONFIG_LOOPW
-#ifdef VOICEBLUE_SMALL_FLASH
-#define CONFIG_BOOTDELAY 0
-#undef CONFIG_BOOTARGS /* the preboot command will set bootargs*/
-#define CFG_AUTOLOAD "n" /* no autoload */
-#define CONFIG_PREBOOT "run setup"
-#define CONFIG_EXTRA_ENV_SETTINGS \
- "setup=setenv bootargs console=ttyS0,${baudrate} " \
- "root=/dev/nfs ip=dhcp\0" \
- "update=erase c000000 c03ffff; " \
- "cp.b 10400000 c000000 ${filesize}\0"
-#else
#define CONFIG_BOOTDELAY 3
-#undef CONFIG_BOOTARGS /* boot command will set bootargs */
-#define CFG_AUTOLOAD "n" /* no autoload */
+#define CONFIG_ZERO_BOOTDELAY_CHECK /* allow to break in always */
+#undef CONFIG_BOOTARGS /* the boot command will set bootargs*/
+#define CFG_AUTOLOAD "n" /* No autoload */
#define CONFIG_BOOTCOMMAND "run nboot"
#define CONFIG_PREBOOT "run setup"
#define CONFIG_EXTRA_ENV_SETTINGS \
"silent=1\0" \
"ospart=0\0" \
- "swapos=no\0" \
+ "bootfile=/boot/uImage\0" \
"setpart=" \
- "if test $swapos = yes; then " \
- "if test $ospart -eq 0; then chpart 4; else chpart 3; fi; "\
- "setenv swapos no; saveenv; " \
- "else " \
- "if test $ospart -eq 0; then chpart 3; else chpart 4; fi; "\
+ "if test -n $swapos; then " \
+ "setenv swapos; saveenv; " \
+ "if test $ospart -eq 0; then setenv ospart 1; else setenv ospart 0; fi; "\
"fi\0" \
"setup=setenv bootargs console=ttyS0,$baudrate " \
"mtdparts=$mtdparts\0" \
@@ -198,16 +170,14 @@
"ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname::off " \
"nfsroot=$rootpath root=/dev/nfs\0" \
"flashargs=run setpart; setenv bootargs $bootargs " \
- "root=/dev/mtdblock$partition ro " \
+ "root=mtd:data$ospart ro " \
"rootfstype=jffs2\0" \
"initrdargs=setenv bootargs $bootargs " \
"ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname::off\0" \
- "fboot=run flashargs; fsload /boot/uImage; bootm\0" \
- "iboot=bootp; run initrdargs; tftp; bootm\0" \
+ "fboot=run flashargs; chpart data$ospart; fsload; bootm\0" \
+ "mboot=bootp; run initrdargs; tftp; bootm\0" \
"nboot=bootp; run nfsargs; tftp; bootm\0"
-#endif
-#ifndef VOICEBLUE_SMALL_FLASH
#define CONFIG_SILENT_CONSOLE 1 /* enable silent startup */
#if 1 /* feel free to disable for development */
@@ -221,19 +191,15 @@
*/
#define CONFIG_JFFS2_CMDLINE
#define MTDIDS_DEFAULT "nor0=omapflash.0"
-#define MTDPARTS_DEFAULT "mtdparts=omapflash.0:128k(uboot),64k(env),64k(r_env),16256k(data1),-(data2)"
-
-#endif /* VOICEBLUE_SMALL_FLASH */
+#define MTDPARTS_DEFAULT "mtdparts=omapflash.0:256k(u-boot),64k(env),64k(r_env),16192k(data0),-(data1)"
/*
* Miscellaneous configurable options
*/
-#ifndef VOICEBLUE_SMALL_FLASH
#define CFG_HUSH_PARSER
#define CFG_PROMPT_HUSH_PS2 "> "
#define CONFIG_AUTO_COMPLETE
-#endif
#define CFG_LONGHELP /* undef to save memory */
#define CFG_PROMPT "# " /* Monitor Command Prompt */
#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
diff --git a/include/configs/xsengine.h b/include/configs/xsengine.h
index 766617e..d167e01 100644
--- a/include/configs/xsengine.h
+++ b/include/configs/xsengine.h
@@ -33,7 +33,7 @@
#define CONFIG_XSENGINE 1
#define CONFIG_MMC 1
#define CONFIG_DOS_PARTITION 1
-#define BOARD_POST_INIT 1
+#define OARD_LATE_INIT 1
#undef CONFIG_USE_IRQ /* we don't need IRQ/FIQ stuff */
#define CFG_HZ 3686400 /* incrementer freq: 3.6864 MHz */
diff --git a/include/mpc512x.h b/include/mpc512x.h
index d1c6fb2..b51cf78 100644
--- a/include/mpc512x.h
+++ b/include/mpc512x.h
@@ -185,7 +185,7 @@
/* SCFR1 System Clock Frequency Register 1
*/
-#define SCFR1_IPS_DIV 0x4
+#define SCFR1_IPS_DIV 0x3
#define SCFR1_IPS_DIV_MASK 0x03800000
#define SCFR1_IPS_DIV_SHIFT 23
diff --git a/include/part.h b/include/part.h
index 37b2b68..8407aa0 100644
--- a/include/part.h
+++ b/include/part.h
@@ -59,6 +59,7 @@
#define IF_TYPE_USB 4
#define IF_TYPE_DOC 5
#define IF_TYPE_MMC 6
+#define IF_TYPE_SD 7
/* Part types */
#define PART_TYPE_UNKNOWN 0x00
diff --git a/include/serial.h b/include/serial.h
index e292f0c..2b99e53 100644
--- a/include/serial.h
+++ b/include/serial.h
@@ -36,6 +36,11 @@
#endif
+#if defined(CONFIG_S3C2410)
+extern struct serial_device s3c24xx_serial0_device;
+extern struct serial_device s3c24xx_serial1_device;
+extern struct serial_device s3c24xx_serial2_device;
+#endif
extern struct serial_device serial_ffuart_device;
extern struct serial_device serial_btuart_device;
diff --git a/lib_arm/board.c b/lib_arm/board.c
index 7e7a282..22d573a 100644
--- a/lib_arm/board.c
+++ b/lib_arm/board.c
@@ -84,6 +84,11 @@
extern void rtl8019_get_enetaddr (uchar * addr);
#endif
+#if defined(CONFIG_HARD_I2C) || \
+ defined(CONFIG_SOFT_I2C)
+#include <i2c.h>
+#endif
+
/*
* Begin and End of memory area for malloc(), and current "brk"
*/
@@ -209,6 +214,16 @@
}
#endif /* CFG_NO_FLASH */
+#if defined(CONFIG_HARD_I2C) || defined(CONFIG_SOFT_I2C)
+static int init_func_i2c (void)
+{
+ puts ("I2C: ");
+ i2c_init (CFG_I2C_SPEED, CFG_I2C_SLAVE);
+ puts ("ready\n");
+ return (0);
+}
+#endif
+
/*
* Breathe some life into the board...
*
@@ -251,6 +266,9 @@
#if defined(CONFIG_DISPLAY_BOARDINFO)
checkboard, /* display board info */
#endif
+#if defined(CONFIG_HARD_I2C) || defined(CONFIG_SOFT_I2C)
+ init_func_i2c,
+#endif
dram_init, /* configure available RAM banks */
display_dram_config,
NULL,
diff --git a/net/tftp.c b/net/tftp.c
index 8b95bcf..3dd2b06 100644
--- a/net/tftp.c
+++ b/net/tftp.c
@@ -34,7 +34,7 @@
#define TFTP_ERROR 5
#define TFTP_OACK 6
-
+static IPaddr_t TftpServerIP;
static int TftpServerPort; /* The UDP port at their end */
static int TftpOurPort; /* The UDP port at our end */
static int TftpTimeoutCount;
@@ -55,7 +55,14 @@
#define DEFAULT_NAME_LEN (8 + 4 + 1)
static char default_filename[DEFAULT_NAME_LEN];
-static char *tftp_filename;
+
+#ifndef CONFIG_TFTP_FILE_NAME_MAX_LEN
+#define MAX_LEN 128
+#else
+#define MAX_LEN CONFIG_TFTP_FILE_NAME_MAX_LEN
+#endif
+
+static char tftp_filename[MAX_LEN];
#ifdef CFG_DIRECT_FLASH_TFTP
extern flash_info_t flash_info[];
@@ -231,7 +238,7 @@
break;
}
- NetSendUDPPacket(NetServerEther, NetServerIP, TftpServerPort, TftpOurPort, len);
+ NetSendUDPPacket(NetServerEther, TftpServerIP, TftpServerPort, TftpOurPort, len);
}
@@ -372,7 +379,7 @@
#ifdef CONFIG_MCAST_TFTP
/* if I am the MasterClient, actively calculate what my next
* needed block is; else I'm passive; not ACKING
- */
+ */
if (Multicast) {
if (len < TftpBlkSize) {
TftpEndingBlock = TftpBlock;
@@ -453,30 +460,43 @@
char *ep; /* Environment pointer */
#endif
+ TftpServerIP = NetServerIP;
if (BootFile[0] == '\0') {
sprintf(default_filename, "%02lX%02lX%02lX%02lX.img",
NetOurIP & 0xFF,
(NetOurIP >> 8) & 0xFF,
(NetOurIP >> 16) & 0xFF,
(NetOurIP >> 24) & 0xFF );
- tftp_filename = default_filename;
+
+ strncpy(tftp_filename, default_filename, MAX_LEN);
+ tftp_filename[MAX_LEN-1] = 0;
printf ("*** Warning: no boot file name; using '%s'\n",
tftp_filename);
} else {
- tftp_filename = BootFile;
+ char *p = strchr (p, ':');
+
+ if (p == NULL) {
+ strncpy(tftp_filename, BootFile, MAX_LEN);
+ tftp_filename[MAX_LEN-1] = 0;
+ } else {
+ *p++ = '\0';
+ TftpServerIP = string_to_ip (BootFile);
+ strncpy(tftp_filename, p, MAX_LEN);
+ tftp_filename[MAX_LEN-1] = 0;
+ }
}
#if defined(CONFIG_NET_MULTI)
printf ("Using %s device\n", eth_get_name());
#endif
- puts ("TFTP from server "); print_IPaddr (NetServerIP);
+ puts ("TFTP from server "); print_IPaddr (TftpServerIP);
puts ("; our IP address is "); print_IPaddr (NetOurIP);
/* Check if we need to send across this subnet */
if (NetOurGatewayIP && NetOurSubnetMask) {
- IPaddr_t OurNet = NetOurIP & NetOurSubnetMask;
- IPaddr_t ServerNet = NetServerIP & NetOurSubnetMask;
+ IPaddr_t OurNet = NetOurIP & NetOurSubnetMask;
+ IPaddr_t ServerNet = TftpServerIP & NetOurSubnetMask;
if (OurNet != ServerNet) {
puts ("; sending through gateway ");
@@ -522,7 +542,7 @@
/* Revert TftpBlkSize to dflt */
TftpBlkSize = TFTP_BLOCK_SIZE;
#ifdef CONFIG_MCAST_TFTP
- mcast_cleanup();
+ mcast_cleanup();
#endif
TftpSend ();
diff --git a/post/tests.c b/post/tests.c
index 0c49e32..698f85c 100644
--- a/post/tests.c
+++ b/post/tests.c
@@ -241,8 +241,8 @@
{
"ECC test",
"ecc",
- "This test checks ECC facility of memory.",
- POST_ROM | POST_ALWAYS,
+ "This test checks the ECC facility of memory.",
+ POST_ROM | POST_ALWAYS | POST_PREREL,
&ecc_post_test,
NULL,
NULL,