drivers: net: add NXP ENETC ethernet driver
Adds a driver for NXP ENETC ethernet controller currently integrated in
LS1028A. ENETC is a fairly straight-forward BD ring device and interfaces
are presented as PCI EPs on the SoC ECAM.
Signed-off-by: Catalin Horghidan <catalin.horghidan@nxp.com>
Signed-off-by: Alex Marginean <alexm.osslist@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
diff --git a/drivers/net/fsl_enetc.c b/drivers/net/fsl_enetc.c
new file mode 100644
index 0000000..58ba63c
--- /dev/null
+++ b/drivers/net/fsl_enetc.c
@@ -0,0 +1,380 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * ENETC ethernet controller driver
+ * Copyright 2017-2019 NXP
+ */
+
+#include <common.h>
+#include <dm.h>
+#include <errno.h>
+#include <memalign.h>
+#include <asm/io.h>
+#include <pci.h>
+
+#include "fsl_enetc.h"
+
+/*
+ * Bind the device:
+ * - set a more explicit name on the interface
+ */
+static int enetc_bind(struct udevice *dev)
+{
+ char name[16];
+ static int eth_num_devices;
+
+ /*
+ * prefer using PCI function numbers to number interfaces, but these
+ * are only available if dts nodes are present. For PCI they are
+ * optional, handle that case too. Just in case some nodes are present
+ * and some are not, use different naming scheme - enetc-N based on
+ * PCI function # and enetc#N based on interface count
+ */
+ if (ofnode_valid(dev->node))
+ sprintf(name, "enetc-%u", PCI_FUNC(pci_get_devfn(dev)));
+ else
+ sprintf(name, "enetc#%u", eth_num_devices++);
+ device_set_name(dev, name);
+
+ return 0;
+}
+
+/*
+ * Probe ENETC driver:
+ * - initialize port and station interface BARs
+ */
+static int enetc_probe(struct udevice *dev)
+{
+ struct enetc_priv *priv = dev_get_priv(dev);
+
+ if (ofnode_valid(dev->node) && !ofnode_is_available(dev->node)) {
+ enetc_dbg(dev, "interface disabled\n");
+ return -ENODEV;
+ }
+
+ priv->enetc_txbd = memalign(ENETC_BD_ALIGN,
+ sizeof(struct enetc_tx_bd) * ENETC_BD_CNT);
+ priv->enetc_rxbd = memalign(ENETC_BD_ALIGN,
+ sizeof(union enetc_rx_bd) * ENETC_BD_CNT);
+
+ if (!priv->enetc_txbd || !priv->enetc_rxbd) {
+ /* free should be able to handle NULL, just free all pointers */
+ free(priv->enetc_txbd);
+ free(priv->enetc_rxbd);
+
+ return -ENOMEM;
+ }
+
+ /* initialize register */
+ priv->regs_base = dm_pci_map_bar(dev, PCI_BASE_ADDRESS_0, 0);
+ if (!priv->regs_base) {
+ enetc_dbg(dev, "failed to map BAR0\n");
+ return -EINVAL;
+ }
+ priv->port_regs = priv->regs_base + ENETC_PORT_REGS_OFF;
+
+ dm_pci_clrset_config16(dev, PCI_COMMAND, 0, PCI_COMMAND_MEMORY);
+
+ return 0;
+}
+
+/*
+ * Remove the driver from an interface:
+ * - free up allocated memory
+ */
+static int enetc_remove(struct udevice *dev)
+{
+ struct enetc_priv *priv = dev_get_priv(dev);
+
+ free(priv->enetc_txbd);
+ free(priv->enetc_rxbd);
+
+ return 0;
+}
+
+/* ENETC Port MAC address registers, accepts big-endian format */
+static void enetc_set_primary_mac_addr(struct enetc_priv *priv, const u8 *addr)
+{
+ u16 lower = *(const u16 *)(addr + 4);
+ u32 upper = *(const u32 *)addr;
+
+ enetc_write_port(priv, ENETC_PSIPMAR0, upper);
+ enetc_write_port(priv, ENETC_PSIPMAR1, lower);
+}
+
+/* Configure port parameters (# of rings, frame size, enable port) */
+static void enetc_enable_si_port(struct enetc_priv *priv)
+{
+ u32 val;
+
+ /* set Rx/Tx BDR count */
+ val = ENETC_PSICFGR_SET_TXBDR(ENETC_TX_BDR_CNT);
+ val |= ENETC_PSICFGR_SET_RXBDR(ENETC_RX_BDR_CNT);
+ enetc_write_port(priv, ENETC_PSICFGR(0), val);
+ /* set Rx max frame size */
+ enetc_write_port(priv, ENETC_PM_MAXFRM, ENETC_RX_MAXFRM_SIZE);
+ /* enable MAC port */
+ enetc_write_port(priv, ENETC_PM_CC, ENETC_PM_CC_RX_TX_EN);
+ /* enable port */
+ enetc_write_port(priv, ENETC_PMR, ENETC_PMR_SI0_EN);
+ /* set SI cache policy */
+ enetc_write(priv, ENETC_SICAR0,
+ ENETC_SICAR_RD_CFG | ENETC_SICAR_WR_CFG);
+ /* enable SI */
+ enetc_write(priv, ENETC_SIMR, ENETC_SIMR_EN);
+}
+
+/* returns DMA address for a given buffer index */
+static inline u64 enetc_rxb_address(struct udevice *dev, int i)
+{
+ return cpu_to_le64(dm_pci_virt_to_mem(dev, net_rx_packets[i]));
+}
+
+/*
+ * Setup a single Tx BD Ring (ID = 0):
+ * - set Tx buffer descriptor address
+ * - set the BD count
+ * - initialize the producer and consumer index
+ */
+static void enetc_setup_tx_bdr(struct udevice *dev)
+{
+ struct enetc_priv *priv = dev_get_priv(dev);
+ struct bd_ring *tx_bdr = &priv->tx_bdr;
+ u64 tx_bd_add = (u64)priv->enetc_txbd;
+
+ /* used later to advance to the next Tx BD */
+ tx_bdr->bd_count = ENETC_BD_CNT;
+ tx_bdr->next_prod_idx = 0;
+ tx_bdr->next_cons_idx = 0;
+ tx_bdr->cons_idx = priv->regs_base +
+ ENETC_BDR(TX, ENETC_TX_BDR_ID, ENETC_TBCIR);
+ tx_bdr->prod_idx = priv->regs_base +
+ ENETC_BDR(TX, ENETC_TX_BDR_ID, ENETC_TBPIR);
+
+ /* set Tx BD address */
+ enetc_bdr_write(priv, TX, ENETC_TX_BDR_ID, ENETC_TBBAR0,
+ lower_32_bits(tx_bd_add));
+ enetc_bdr_write(priv, TX, ENETC_TX_BDR_ID, ENETC_TBBAR1,
+ upper_32_bits(tx_bd_add));
+ /* set Tx 8 BD count */
+ enetc_bdr_write(priv, TX, ENETC_TX_BDR_ID, ENETC_TBLENR,
+ tx_bdr->bd_count);
+
+ /* reset both producer/consumer indexes */
+ enetc_write_reg(tx_bdr->cons_idx, tx_bdr->next_cons_idx);
+ enetc_write_reg(tx_bdr->prod_idx, tx_bdr->next_prod_idx);
+
+ /* enable TX ring */
+ enetc_bdr_write(priv, TX, ENETC_TX_BDR_ID, ENETC_TBMR, ENETC_TBMR_EN);
+}
+
+/*
+ * Setup a single Rx BD Ring (ID = 0):
+ * - set Rx buffer descriptors address (one descriptor per buffer)
+ * - set buffer size as max frame size
+ * - enable Rx ring
+ * - reset consumer and producer indexes
+ * - set buffer for each descriptor
+ */
+static void enetc_setup_rx_bdr(struct udevice *dev)
+{
+ struct enetc_priv *priv = dev_get_priv(dev);
+ struct bd_ring *rx_bdr = &priv->rx_bdr;
+ u64 rx_bd_add = (u64)priv->enetc_rxbd;
+ int i;
+
+ /* used later to advance to the next BD produced by ENETC HW */
+ rx_bdr->bd_count = ENETC_BD_CNT;
+ rx_bdr->next_prod_idx = 0;
+ rx_bdr->next_cons_idx = 0;
+ rx_bdr->cons_idx = priv->regs_base +
+ ENETC_BDR(RX, ENETC_RX_BDR_ID, ENETC_RBCIR);
+ rx_bdr->prod_idx = priv->regs_base +
+ ENETC_BDR(RX, ENETC_RX_BDR_ID, ENETC_RBPIR);
+
+ /* set Rx BD address */
+ enetc_bdr_write(priv, RX, ENETC_RX_BDR_ID, ENETC_RBBAR0,
+ lower_32_bits(rx_bd_add));
+ enetc_bdr_write(priv, RX, ENETC_RX_BDR_ID, ENETC_RBBAR1,
+ upper_32_bits(rx_bd_add));
+ /* set Rx BD count (multiple of 8) */
+ enetc_bdr_write(priv, RX, ENETC_RX_BDR_ID, ENETC_RBLENR,
+ rx_bdr->bd_count);
+ /* set Rx buffer size */
+ enetc_bdr_write(priv, RX, ENETC_RX_BDR_ID, ENETC_RBBSR, PKTSIZE_ALIGN);
+
+ /* fill Rx BD */
+ memset(priv->enetc_rxbd, 0,
+ rx_bdr->bd_count * sizeof(union enetc_rx_bd));
+ for (i = 0; i < rx_bdr->bd_count; i++) {
+ priv->enetc_rxbd[i].w.addr = enetc_rxb_address(dev, i);
+ /* each RX buffer must be aligned to 64B */
+ WARN_ON(priv->enetc_rxbd[i].w.addr & (ARCH_DMA_MINALIGN - 1));
+ }
+
+ /* reset producer (ENETC owned) and consumer (SW owned) index */
+ enetc_write_reg(rx_bdr->cons_idx, rx_bdr->next_cons_idx);
+ enetc_write_reg(rx_bdr->prod_idx, rx_bdr->next_prod_idx);
+
+ /* enable Rx ring */
+ enetc_bdr_write(priv, RX, ENETC_RX_BDR_ID, ENETC_RBMR, ENETC_RBMR_EN);
+}
+
+/*
+ * Start ENETC interface:
+ * - perform FLR
+ * - enable access to port and SI registers
+ * - set mac address
+ * - setup TX/RX buffer descriptors
+ * - enable Tx/Rx rings
+ */
+static int enetc_start(struct udevice *dev)
+{
+ struct eth_pdata *plat = dev_get_platdata(dev);
+ struct enetc_priv *priv = dev_get_priv(dev);
+
+ /* reset and enable the PCI device */
+ dm_pci_flr(dev);
+ dm_pci_clrset_config16(dev, PCI_COMMAND, 0,
+ PCI_COMMAND_MEMORY | PCI_COMMAND_MASTER);
+
+ if (!is_valid_ethaddr(plat->enetaddr)) {
+ enetc_dbg(dev, "invalid MAC address, generate random ...\n");
+ net_random_ethaddr(plat->enetaddr);
+ }
+ enetc_set_primary_mac_addr(priv, plat->enetaddr);
+
+ enetc_enable_si_port(priv);
+
+ /* setup Tx/Rx buffer descriptors */
+ enetc_setup_tx_bdr(dev);
+ enetc_setup_rx_bdr(dev);
+
+ return 0;
+}
+
+/*
+ * Stop the network interface:
+ * - just quiesce it, we can wipe all configuration as _start starts from
+ * scratch each time
+ */
+static void enetc_stop(struct udevice *dev)
+{
+ /* FLR is sufficient to quiesce the device */
+ dm_pci_flr(dev);
+}
+
+/*
+ * ENETC transmit packet:
+ * - check if Tx BD ring is full
+ * - set buffer/packet address (dma address)
+ * - set final fragment flag
+ * - try while producer index equals consumer index or timeout
+ */
+static int enetc_send(struct udevice *dev, void *packet, int length)
+{
+ struct enetc_priv *priv = dev_get_priv(dev);
+ struct bd_ring *txr = &priv->tx_bdr;
+ void *nv_packet = (void *)packet;
+ int tries = ENETC_POLL_TRIES;
+ u32 pi, ci;
+
+ pi = txr->next_prod_idx;
+ ci = enetc_read_reg(txr->cons_idx) & ENETC_BDR_IDX_MASK;
+ /* Tx ring is full when */
+ if (((pi + 1) % txr->bd_count) == ci) {
+ enetc_dbg(dev, "Tx BDR full\n");
+ return -ETIMEDOUT;
+ }
+ enetc_dbg(dev, "TxBD[%d]send: pkt_len=%d, buff @0x%x%08x\n", pi, length,
+ upper_32_bits((u64)nv_packet), lower_32_bits((u64)nv_packet));
+
+ /* prepare Tx BD */
+ memset(&priv->enetc_txbd[pi], 0x0, sizeof(struct enetc_tx_bd));
+ priv->enetc_txbd[pi].addr =
+ cpu_to_le64(dm_pci_virt_to_mem(dev, nv_packet));
+ priv->enetc_txbd[pi].buf_len = cpu_to_le16(length);
+ priv->enetc_txbd[pi].frm_len = cpu_to_le16(length);
+ priv->enetc_txbd[pi].flags = cpu_to_le16(ENETC_TXBD_FLAGS_F);
+ dmb();
+ /* send frame: increment producer index */
+ pi = (pi + 1) % txr->bd_count;
+ txr->next_prod_idx = pi;
+ enetc_write_reg(txr->prod_idx, pi);
+ while ((--tries >= 0) &&
+ (pi != (enetc_read_reg(txr->cons_idx) & ENETC_BDR_IDX_MASK)))
+ udelay(10);
+
+ return tries > 0 ? 0 : -ETIMEDOUT;
+}
+
+/*
+ * Receive frame:
+ * - wait for the next BD to get ready bit set
+ * - clean up the descriptor
+ * - move on and indicate to HW that the cleaned BD is available for Rx
+ */
+static int enetc_recv(struct udevice *dev, int flags, uchar **packetp)
+{
+ struct enetc_priv *priv = dev_get_priv(dev);
+ struct bd_ring *rxr = &priv->rx_bdr;
+ int tries = ENETC_POLL_TRIES;
+ int pi = rxr->next_prod_idx;
+ int ci = rxr->next_cons_idx;
+ u32 status;
+ int len;
+ u8 rdy;
+
+ do {
+ dmb();
+ status = le32_to_cpu(priv->enetc_rxbd[pi].r.lstatus);
+ /* check if current BD is ready to be consumed */
+ rdy = ENETC_RXBD_STATUS_R(status);
+ } while (--tries >= 0 && !rdy);
+
+ if (!rdy)
+ return -EAGAIN;
+
+ dmb();
+ len = le16_to_cpu(priv->enetc_rxbd[pi].r.buf_len);
+ *packetp = (uchar *)enetc_rxb_address(dev, pi);
+ enetc_dbg(dev, "RxBD[%d]: len=%d err=%d pkt=0x%x%08x\n", pi, len,
+ ENETC_RXBD_STATUS_ERRORS(status),
+ upper_32_bits((u64)*packetp), lower_32_bits((u64)*packetp));
+
+ /* BD clean up and advance to next in ring */
+ memset(&priv->enetc_rxbd[pi], 0, sizeof(union enetc_rx_bd));
+ priv->enetc_rxbd[pi].w.addr = enetc_rxb_address(dev, pi);
+ rxr->next_prod_idx = (pi + 1) % rxr->bd_count;
+ ci = (ci + 1) % rxr->bd_count;
+ rxr->next_cons_idx = ci;
+ dmb();
+ /* free up the slot in the ring for HW */
+ enetc_write_reg(rxr->cons_idx, ci);
+
+ return len;
+}
+
+static const struct eth_ops enetc_ops = {
+ .start = enetc_start,
+ .send = enetc_send,
+ .recv = enetc_recv,
+ .stop = enetc_stop,
+};
+
+U_BOOT_DRIVER(eth_enetc) = {
+ .name = "enetc_eth",
+ .id = UCLASS_ETH,
+ .bind = enetc_bind,
+ .probe = enetc_probe,
+ .remove = enetc_remove,
+ .ops = &enetc_ops,
+ .priv_auto_alloc_size = sizeof(struct enetc_priv),
+ .platdata_auto_alloc_size = sizeof(struct eth_pdata),
+};
+
+static struct pci_device_id enetc_ids[] = {
+ { PCI_DEVICE(PCI_VENDOR_ID_FREESCALE, PCI_DEVICE_ID_ENETC_ETH) },
+ {}
+};
+
+U_BOOT_PCI_DEVICE(eth_enetc, enetc_ids);