* Patches by Thomas Lange, 09 Oct 2003:
- fix cmd_ide.c for non ppc boards (read/write functions did not
add ATA base address)
- fix for shannon board
- #ifdef CONFIG_IDE_8xx_DIRECT some otherwise unused code
* Patch by Sangmoon Kim, 07 Oct 2003:
add support for debris board
diff --git a/include/configs/debris.h b/include/configs/debris.h
new file mode 100644
index 0000000..587798c
--- /dev/null
+++ b/include/configs/debris.h
@@ -0,0 +1,439 @@
+/*
+ * (C) Copyright 2001, 2002
+ * Sangmoon Kim, Etin Systems, dogoil@etinsys.com.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+/* ------------------------------------------------------------------------- */
+
+/*
+ * board/config.h - configuration options, board specific
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/* Environments */
+
+/* bootargs */
+#define CONFIG_BOOTARGS \
+ "console=ttyS0,9600 init=/linuxrc " \
+ "root=/dev/nfs rw nfsroot=192.168.0.1:" \
+ "/tftpboot/target " \
+ "ip=192.168.0.2:192.168.0.1:192.168.0.1:" \
+ "255.255.255.0:debris:eth0:none " \
+ "mtdparts=phys:12m(root),-(kernel)"
+
+/* bootcmd */
+#define CONFIG_BOOTCOMMAND \
+ "tftp 800000 pImage; " \
+ "setenv bootargs console=ttyS0,9600 init=/linuxrc " \
+ "root=/dev/nfs rw nfsroot=$(serverip):$(rootpath) " \
+ "ip=$(ipaddr):$(serverip):$(gatewayip):" \
+ "$(netmask):$(hostname):eth0:none " \
+ "mtdparts=phys:12m(root),-(kernel); " \
+ "bootm 800000"
+
+/* bootdelay */
+#define CONFIG_BOOTDELAY 5 /* autoboot 5s */
+
+/* baudrate */
+#define CONFIG_BAUDRATE 9600 /* console baudrate = 9600bps */
+
+/* loads_echo */
+#define CONFIG_LOADS_ECHO 0 /* echo off for serial download */
+
+/* ethaddr */
+#undef CONFIG_ETHADDR
+
+/* eth2addr */
+#undef CONFIG_ETH2ADDR
+
+/* eth3addr */
+#undef CONFIG_ETH3ADDR
+
+/* ipaddr */
+#define CONFIG_IPADDR 192.168.0.2
+
+/* serverip */
+#define CONFIG_SERVERIP 192.168.0.1
+
+/* autoload */
+#undef CFG_AUTOLOAD
+
+/* rootpath */
+#define CONFIG_ROOTPATH /tftpboot/target
+
+/* gatewayip */
+#define CONFIG_GATEWAYIP 192.168.0.1
+
+/* netmask */
+#define CONFIG_NETMASK 255.255.255.0
+
+/* hostname */
+#define CONFIG_HOSTNAME debris
+
+/* bootfile */
+#define CONFIG_BOOTFILE pImage
+
+/* loadaddr */
+#define CONFIG_LOADADDR 800000
+
+/* preboot */
+#undef CONFIG_PREBOOT
+
+/* clocks_in_mhz */
+#undef CONFIG_CLOCKS_IN_MHZ
+
+
+/*
+ * High Level Configuration Options
+ * (easy to change)
+ */
+
+#define CONFIG_MPC824X 1
+#define CONFIG_MPC8245 1
+#define CONFIG_DEBRIS 1
+
+#if 0
+#define USE_DINK32 1
+#else
+#undef USE_DINK32
+#endif
+
+#define CONFIG_CONS_INDEX 1
+#define CONFIG_BAUDRATE 9600
+#define CONFIG_DRAM_SPEED 100 /* MHz */
+
+#define CONFIG_COMMANDS ( CONFIG_CMD_DFL | \
+ CFG_CMD_ASKENV | \
+ CFG_CMD_CACHE | \
+ CFG_CMD_DATE | \
+ CFG_CMD_DHCP | \
+ CFG_CMD_DIAG | \
+ CFG_CMD_EEPROM | \
+ CFG_CMD_ELF | \
+ CFG_CMD_I2C | \
+ CFG_CMD_JFFS2 | \
+ CFG_CMD_KGBD | \
+ CFG_CMD_PCI | \
+ CFG_CMD_PING | \
+ CFG_CMD_SAVES | \
+ CFG_CMD_SDRAM)
+/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
+#include <cmd_confdefs.h>
+
+
+/*
+ * Miscellaneous configurable options
+ */
+#define CFG_LONGHELP 1 /* undef to save memory */
+#define CFG_PROMPT "=> " /* Monitor Command Prompt */
+#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
+#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
+#define CFG_MAXARGS 16 /* max number of command args */
+#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
+#define CFG_LOAD_ADDR 0x00100000 /* default load address */
+#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
+
+/*-----------------------------------------------------------------------
+ * PCI stuff
+ *-----------------------------------------------------------------------
+ */
+#define CONFIG_PCI /* include pci support */
+#define CONFIG_PCI_PNP
+
+#define CONFIG_NET_MULTI /* Multi ethernet cards support */
+#define CONFIG_EEPRO100
+#define CFG_RX_ETH_BUFFER 8 /* use 8 rx buffer on eepro100 */
+#define CONFIG_EEPRO100_SROM_WRITE
+
+#define PCI_ENET0_IOADDR 0x80000000
+#define PCI_ENET0_MEMADDR 0x80000000
+#define PCI_ENET1_IOADDR 0x81000000
+#define PCI_ENET1_MEMADDR 0x81000000
+/*-----------------------------------------------------------------------
+ * Start addresses for the final memory configuration
+ * (Set up by the startup code)
+ * Please note that CFG_SDRAM_BASE _must_ start at 0
+ */
+#define CFG_SDRAM_BASE 0x00000000
+#define CFG_MAX_RAM_SIZE 0x10000000
+
+#define CFG_RESET_ADDRESS 0xFFF00100
+
+#if defined (USE_DINK32)
+#define CFG_MONITOR_LEN 0x00040000
+#define CFG_MONITOR_BASE 0x00090000
+#define CFG_RAMBOOT 1
+#define CFG_INIT_RAM_ADDR (CFG_MONITOR_BASE + CFG_MONITOR_LEN)
+#define CFG_INIT_RAM_END 0x10000
+#define CFG_GBL_DATA_SIZE 256 /* size in bytes reserved for initial data */
+#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
+#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
+#else
+#undef CFG_RAMBOOT
+#define CFG_MONITOR_LEN 0x00040000
+#define CFG_MONITOR_BASE TEXT_BASE
+
+/*#define CFG_GBL_DATA_SIZE 256*/
+#define CFG_GBL_DATA_SIZE 128
+
+#define CFG_INIT_RAM_ADDR 0x40000000
+#define CFG_INIT_RAM_END 0x1000
+#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
+
+#endif
+
+#define CFG_FLASH_BASE 0x7C000000
+#define CFG_FLASH_SIZE (16*1024*1024) /* debris has tiny eeprom */
+
+#define CFG_MALLOC_LEN (512 << 10) /* Reserve 512 kB for malloc() */
+
+#define CFG_MEMTEST_START 0x00000000 /* memtest works on */
+#define CFG_MEMTEST_END 0x04000000 /* 0 ... 32 MB in DRAM */
+
+#define CFG_EUMB_ADDR 0xFC000000
+
+#define CFG_FLASH_RANGE_BASE 0xFF000000 /* flash memory address range */
+#define CFG_FLASH_RANGE_SIZE 0x01000000
+#define FLASH_BASE0_PRELIM 0x7C000000 /* debris flash */
+
+#define CFG_JFFS2_FIRST_BANK 0 /* use for JFFS2 */
+#define CFG_JFFS2_NUM_BANKS 1
+
+#define CFG_ENV_IS_IN_NVRAM 1
+#define CONFIG_ENV_OVERWRITE 1
+#define CFG_NVRAM_ACCESS_ROUTINE 1
+#define CFG_ENV_ADDR 0xFF000000 /* right at the start of NVRAM */
+#define CFG_ENV_SIZE 0x400 /* Size of the Environment - 8K */
+#define CFG_ENV_OFFSET 0 /* starting right at the beginning */
+
+#define CFG_NVRAM_BASE_ADDR 0xff000000
+
+/*
+ * CFG_NVRAM_BASE_ADDR + CFG_NVRAM_VXWORKS_OFFS =
+ * NV_RAM_ADDRS + NV_BOOT_OFFSET + NV_ENET_OFFSET
+ */
+#define CFG_NVRAM_VXWORKS_OFFS 0x6900
+
+/*
+ * select i2c support configuration
+ *
+ * Supported configurations are {none, software, hardware} drivers.
+ * If the software driver is chosen, there are some additional
+ * configuration items that the driver uses to drive the port pins.
+ */
+#define CONFIG_HARD_I2C 1 /* To enable I2C support */
+#undef CONFIG_SOFT_I2C /* I2C bit-banged */
+#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */
+#define CFG_I2C_SLAVE 0x7F
+
+#ifdef CONFIG_SOFT_I2C
+#error "Soft I2C is not configured properly. Please review!"
+#define I2C_PORT 3 /* Port A=0, B=1, C=2, D=3 */
+#define I2C_ACTIVE (iop->pdir |= 0x00010000)
+#define I2C_TRISTATE (iop->pdir &= ~0x00010000)
+#define I2C_READ ((iop->pdat & 0x00010000) != 0)
+#define I2C_SDA(bit) if(bit) iop->pdat |= 0x00010000; \
+ else iop->pdat &= ~0x00010000
+#define I2C_SCL(bit) if(bit) iop->pdat |= 0x00020000; \
+ else iop->pdat &= ~0x00020000
+#define I2C_DELAY udelay(5) /* 1/4 I2C clock duration */
+#endif /* CONFIG_SOFT_I2C */
+
+#define CFG_I2C_EEPROM_ADDR 0x57 /* EEPROM IS24C02 */
+#define CFG_I2C_EEPROM_ADDR_LEN 1 /* Bytes of address */
+#define CFG_EEPROM_PAGE_WRITE_BITS 3
+#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10 /* and takes up to 10 msec */
+
+#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
+#define CFG_FLASH_BANKS { FLASH_BASE0_PRELIM }
+
+/*-----------------------------------------------------------------------
+ * Definitions for initial stack pointer and data area (in DPRAM)
+ */
+
+/*
+ * NS16550 Configuration
+ */
+#define CFG_NS16550
+#define CFG_NS16550_SERIAL
+
+#define CFG_NS16550_REG_SIZE 1
+
+#define CFG_NS16550_CLK 7372800
+
+#define CFG_NS16550_COM1 0xFF080000
+#define CFG_NS16550_COM2 (CFG_NS16550_COM1 + 8)
+#define CFG_NS16550_COM3 (CFG_NS16550_COM1 + 16)
+#define CFG_NS16550_COM4 (CFG_NS16550_COM1 + 24)
+
+/*
+ * Low Level Configuration Settings
+ * (address mappings, register initial values, etc.)
+ * You should know what you are doing if you make changes here.
+ */
+
+#define CONFIG_SYS_CLK_FREQ 33333333 /* external frequency to pll */
+#define CONFIG_PLL_PCI_TO_MEM_MULTIPLIER 3
+
+#define CFG_DLL_EXTEND 0x00
+#define CFG_PCI_HOLD_DEL 0x20
+
+#define CFG_ROMNAL 15 /* rom/flash next access time */
+#define CFG_ROMFAL 31 /* rom/flash access time */
+
+#define CFG_REFINT 430 /* # of clocks between CBR refresh cycles */
+
+#define CFG_DBUS_SIZE2 1 /* set for 8-bit RCS1, clear for 32,64 */
+
+/* the following are for SDRAM only*/
+#define CFG_BSTOPRE 121 /* Burst To Precharge, sets open page interval */
+#define CFG_REFREC 8 /* Refresh to activate interval */
+#define CFG_RDLAT 4 /* data latency from read command */
+#define CFG_PRETOACT 3 /* Precharge to activate interval */
+#define CFG_ACTTOPRE 5 /* Activate to Precharge interval */
+#define CFG_ACTORW 3 /* Activate to R/W */
+#define CFG_SDMODE_CAS_LAT 3 /* SDMODE CAS latency */
+#define CFG_SDMODE_WRAP 0 /* SDMODE wrap type */
+#if 0
+#define CFG_SDMODE_BURSTLEN 2 /* OBSOLETE! SDMODE Burst length 2=4, 3=8 */
+#endif
+
+#define CFG_REGISTERD_TYPE_BUFFER 1
+#define CFG_EXTROM 1
+#define CFG_REGDIMM 0
+
+
+/* memory bank settings*/
+/*
+ * only bits 20-29 are actually used from these vales to set the
+ * start/end address the upper two bits will be 0, and the lower 20
+ * bits will be set to 0x00000 for a start address, or 0xfffff for an
+ * end address
+ */
+#define CFG_BANK0_START 0x00000000
+#define CFG_BANK0_END (0x4000000 - 1)
+#define CFG_BANK0_ENABLE 1
+#define CFG_BANK1_START 0x04000000
+#define CFG_BANK1_END (0x8000000 - 1)
+#define CFG_BANK1_ENABLE 1
+#define CFG_BANK2_START 0x3ff00000
+#define CFG_BANK2_END 0x3fffffff
+#define CFG_BANK2_ENABLE 0
+#define CFG_BANK3_START 0x3ff00000
+#define CFG_BANK3_END 0x3fffffff
+#define CFG_BANK3_ENABLE 0
+#define CFG_BANK4_START 0x00000000
+#define CFG_BANK4_END 0x00000000
+#define CFG_BANK4_ENABLE 0
+#define CFG_BANK5_START 0x00000000
+#define CFG_BANK5_END 0x00000000
+#define CFG_BANK5_ENABLE 0
+#define CFG_BANK6_START 0x00000000
+#define CFG_BANK6_END 0x00000000
+#define CFG_BANK6_ENABLE 0
+#define CFG_BANK7_START 0x00000000
+#define CFG_BANK7_END 0x00000000
+#define CFG_BANK7_ENABLE 0
+/*
+ * Memory bank enable bitmask, specifying which of the banks defined above
+ are actually present. MSB is for bank #7, LSB is for bank #0.
+ */
+#define CFG_BANK_ENABLE 0x01
+
+#define CFG_ODCR 0x75 /* configures line driver impedances, */
+ /* see 8240 book for bit definitions */
+#define CFG_PGMAX 0x32 /* how long the 8240 retains the */
+ /* currently accessed page in memory */
+ /* see 8240 book for details */
+
+/* SDRAM 0 - 256MB */
+#define CFG_IBAT0L (CFG_SDRAM_BASE | BATL_PP_10 | BATL_MEMCOHERENCE)
+#define CFG_IBAT0U (CFG_SDRAM_BASE | BATU_BL_256M | BATU_VS | BATU_VP)
+
+/* stack in DCACHE @ 1GB (no backing mem) */
+#if defined(USE_DINK32)
+#define CFG_IBAT1L (0x40000000 | BATL_PP_00 )
+#define CFG_IBAT1U (0x40000000 | BATU_BL_128K )
+#else
+#define CFG_IBAT1L (CFG_INIT_RAM_ADDR | BATL_PP_10 | BATL_MEMCOHERENCE)
+#define CFG_IBAT1U (CFG_INIT_RAM_ADDR | BATU_BL_128K | BATU_VS | BATU_VP)
+#endif
+
+/* PCI memory */
+#define CFG_IBAT2L (0x80000000 | BATL_PP_10 | BATL_CACHEINHIBIT)
+#define CFG_IBAT2U (0x80000000 | BATU_BL_256M | BATU_VS | BATU_VP)
+
+/* Flash, config addrs, etc */
+#define CFG_IBAT3L (0xF0000000 | BATL_PP_10 | BATL_CACHEINHIBIT)
+#define CFG_IBAT3U (0xF0000000 | BATU_BL_256M | BATU_VS | BATU_VP)
+
+#define CFG_DBAT0L CFG_IBAT0L
+#define CFG_DBAT0U CFG_IBAT0U
+#define CFG_DBAT1L CFG_IBAT1L
+#define CFG_DBAT1U CFG_IBAT1U
+#define CFG_DBAT2L CFG_IBAT2L
+#define CFG_DBAT2U CFG_IBAT2U
+#define CFG_DBAT3L CFG_IBAT3L
+#define CFG_DBAT3U CFG_IBAT3U
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 8 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
+/*-----------------------------------------------------------------------
+ * FLASH organization
+ */
+#define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */
+#define CFG_MAX_FLASH_SECT 256 /* max number of sectors on one chip */
+
+#define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
+#define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
+
+/*-----------------------------------------------------------------------
+ * Cache Configuration
+ */
+#define CFG_CACHELINE_SIZE 32 /* For MPC8240 CPU */
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+# define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */
+#endif
+
+
+/*
+ * Internal Definitions
+ *
+ * Boot Flags
+ */
+#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
+#define BOOTFLAG_WARM 0x02 /* Software reboot */
+
+
+/* values according to the manual */
+
+#define CONFIG_DRAM_50MHZ 1
+#define CONFIG_SDRAM_50MHZ
+
+#define CONFIG_DISK_SPINUP_TIME 1000000
+
+#endif /* __CONFIG_H */