fpga: Added support to load bit stream from SD/MMC
Added support to load a bitstream image in chunks by reading it in
chunks from SD/MMC.
Command format:
loadfs [dev] [address] [image size] [blocksize] <interface>
[<dev[:part]>] <filename>
Example: fpga loadfs 0 1000000 3dbafc 4000 mmc 0 fpga.bin
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
diff --git a/drivers/fpga/zynqpl.c b/drivers/fpga/zynqpl.c
index 915f077..68fe0f3 100644
--- a/drivers/fpga/zynqpl.c
+++ b/drivers/fpga/zynqpl.c
@@ -9,6 +9,7 @@
#include <common.h>
#include <asm/io.h>
+#include <fs.h>
#include <zynqpl.h>
#include <linux/sizes.h>
#include <asm/arch/hardware.h>
@@ -398,6 +399,87 @@
return FPGA_SUCCESS;
}
+#if defined(CONFIG_CMD_FPGA_LOADFS)
+static int zynq_loadfs(xilinx_desc *desc, const void *buf, size_t bsize,
+ fpga_fs_info *fsinfo)
+{
+ unsigned long ts; /* Timestamp */
+ u32 isr_status, swap;
+ u32 partialbit = 0;
+ u32 blocksize;
+ u32 pos = 0;
+ int fstype;
+ char *interface, *dev_part, *filename;
+
+ blocksize = fsinfo->blocksize;
+ interface = fsinfo->interface;
+ dev_part = fsinfo->dev_part;
+ filename = fsinfo->filename;
+ fstype = fsinfo->fstype;
+
+ if (fs_set_blk_dev(interface, dev_part, fstype))
+ return FPGA_FAIL;
+
+ if (fs_read(filename, (u32) buf, pos, blocksize) < 0)
+ return FPGA_FAIL;
+
+ if (zynq_validate_bitstream(desc, buf, bsize, blocksize, &swap,
+ &partialbit))
+ return FPGA_FAIL;
+
+ dcache_disable();
+
+ do {
+ buf = zynq_align_dma_buffer((u32 *)buf, blocksize, swap);
+
+ if (zynq_dma_transfer((u32)buf | 1, blocksize >> 2,
+ 0xffffffff, 0))
+ return FPGA_FAIL;
+
+ bsize -= blocksize;
+ pos += blocksize;
+
+ if (fs_set_blk_dev(interface, dev_part, fstype))
+ return FPGA_FAIL;
+
+ if (bsize > blocksize) {
+ if (fs_read(filename, (u32) buf, pos, blocksize) < 0)
+ return FPGA_FAIL;
+ } else {
+ if (fs_read(filename, (u32) buf, pos, bsize) < 0)
+ return FPGA_FAIL;
+ }
+ } while (bsize > blocksize);
+
+ buf = zynq_align_dma_buffer((u32 *)buf, blocksize, swap);
+
+ if (zynq_dma_transfer((u32)buf | 1, bsize >> 2, 0xffffffff, 0))
+ return FPGA_FAIL;
+
+ dcache_enable();
+
+ isr_status = readl(&devcfg_base->int_sts);
+
+ /* Check FPGA configuration completion */
+ ts = get_timer(0);
+ while (!(isr_status & DEVCFG_ISR_PCFG_DONE)) {
+ if (get_timer(ts) > CONFIG_SYS_FPGA_WAIT) {
+ printf("%s: Timeout wait for FPGA to config\n",
+ __func__);
+ return FPGA_FAIL;
+ }
+ isr_status = readl(&devcfg_base->int_sts);
+ }
+
+ debug("%s: FPGA config done\n", __func__);
+
+ if (!partialbit)
+ zynq_slcr_devcfg_enable();
+
+ return FPGA_SUCCESS;
+}
+#endif
+
static int zynq_dump(xilinx_desc *desc, const void *buf, size_t bsize)
{
return FPGA_FAIL;
@@ -405,6 +487,9 @@
struct xilinx_fpga_op zynq_op = {
.load = zynq_load,
+#if defined(CONFIG_CMD_FPGA_LOADFS)
+ .loadfs = zynq_loadfs,
+#endif
.dump = zynq_dump,
.info = zynq_info,
};