ARM: dts: stm32mp1: DT alignment with Linux 5.7-rc2
DT alignment with Linux 5.7-rc2, including the kernel commits
431c89e6f323 ARM: dts: stm32: use correct vqmmc regu for eMMC on stm32mp1 ED1/EV1 boards
79e965053872 ARM: dts: stm32: add disable-wp property for SD-card on STM32MP1 boards
877db62ea516 ARM: dts: stm32: add cd-gpios properties for SD-cards on STM32MP1 boards
7519e95ba5f8 ARM: dts: stm32: Do clean up in stmpic nodes on stm32mp15 boards
f68e2dbc591a ARM: dts: stm32: Rename stmfx joystick pins on stm32mp157c-ev1
d6210da4f8bf ARM: dts: stm32: add cpu clock-frequency property on stm32mp15x
b65b6fc56925 ARM: dts: stm32: add wakeup-source in all I2C nodes of stm32mp157c
1c1cf5996cfb ARM: dts: stm32: add i2c4 sleep pinctrl on stm32mp157c-ed1
bef15fc0fad9 ARM: dts: stm32: add i2c2/i2c5 sleep pinctrl on stm32mp157c-ev1
b7fc0a87b9ac ARM: dts: stm32: add i2c4 sleep pinctrl on stm32mp15xx-dkx
a5e557655285 ARM: dts: stm32: set i2c4 bus freq to 400KHz on stm32mp15 DK boards
8bc631b650a6 ARM: dts: stm32: set i2c4 bus freq to 400KHz on stm32mp157c-ed1
fccd6a577bb3 ARM: dts: stm32: Correct stmfx node name on stm32mp157c-ev1 board
cc775a83db65 ARM: dts: stm32: add resets property on all DMA nodes on stm32mp151
c5fae093511b ARM: dts: stm32: enable USB OTG Dual Role on stm32mp157c-ev1
9879e2165758 ARM: dts: stm32: add USB OTG pinctrl to stm32mp15
82ac8a81f985 ARM: dts: stm32: add USB OTG full support on stm32mp151
8714b26e2863 ARM: dts: stm32: remove useless properties in stm32mp157a-avenger96 stmpic node
a7959919709e ARM: dts: stm32: Add UART8 pins A pinmux entry on stm32mp1
4d7c53a684da ARM: dts: stm32: Add USART3 pins A pinmux entry on stm32mp1
80ab128332ee ARM: dts: stm32: Add SAI2A pins B pinmux entry on stm32mp1
ab7f98c0c546 ARM: dts: stm32: Add Ethernet0 RMII pins A pinmux entry on stm32mp1
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
diff --git a/arch/arm/dts/stm32mp15-pinctrl.dtsi b/arch/arm/dts/stm32mp15-pinctrl.dtsi
index 29acdc4..8d00391 100644
--- a/arch/arm/dts/stm32mp15-pinctrl.dtsi
+++ b/arch/arm/dts/stm32mp15-pinctrl.dtsi
@@ -213,6 +213,40 @@
};
};
+ ethernet0_rmii_pins_a: rmii-0 {
+ pins1 {
+ pinmux = <STM32_PINMUX('G', 13, AF11)>, /* ETH1_RMII_TXD0 */
+ <STM32_PINMUX('G', 14, AF11)>, /* ETH1_RMII_TXD1 */
+ <STM32_PINMUX('B', 11, AF11)>, /* ETH1_RMII_TX_EN */
+ <STM32_PINMUX('A', 1, AF0)>, /* ETH1_RMII_REF_CLK */
+ <STM32_PINMUX('A', 2, AF11)>, /* ETH1_MDIO */
+ <STM32_PINMUX('C', 1, AF11)>; /* ETH1_MDC */
+ bias-disable;
+ drive-push-pull;
+ slew-rate = <2>;
+ };
+ pins2 {
+ pinmux = <STM32_PINMUX('C', 4, AF11)>, /* ETH1_RMII_RXD0 */
+ <STM32_PINMUX('C', 5, AF11)>, /* ETH1_RMII_RXD1 */
+ <STM32_PINMUX('A', 7, AF11)>; /* ETH1_RMII_CRS_DV */
+ bias-disable;
+ };
+ };
+
+ ethernet0_rmii_pins_sleep_a: rmii-sleep-0 {
+ pins1 {
+ pinmux = <STM32_PINMUX('G', 13, ANALOG)>, /* ETH1_RMII_TXD0 */
+ <STM32_PINMUX('G', 14, ANALOG)>, /* ETH1_RMII_TXD1 */
+ <STM32_PINMUX('B', 11, ANALOG)>, /* ETH1_RMII_TX_EN */
+ <STM32_PINMUX('A', 2, ANALOG)>, /* ETH1_MDIO */
+ <STM32_PINMUX('C', 1, ANALOG)>, /* ETH1_MDC */
+ <STM32_PINMUX('C', 4, ANALOG)>, /* ETH1_RMII_RXD0 */
+ <STM32_PINMUX('C', 5, ANALOG)>, /* ETH1_RMII_RXD1 */
+ <STM32_PINMUX('A', 1, ANALOG)>, /* ETH1_RMII_REF_CLK */
+ <STM32_PINMUX('A', 7, ANALOG)>; /* ETH1_RMII_CRS_DV */
+ };
+ };
+
fmc_pins_a: fmc-0 {
pins1 {
pinmux = <STM32_PINMUX('D', 4, AF12)>, /* FMC_NOE */
@@ -736,6 +770,25 @@
};
};
+ sai2a_pins_b: sai2a-2 {
+ pins1 {
+ pinmux = <STM32_PINMUX('I', 6, AF10)>, /* SAI2_SD_A */
+ <STM32_PINMUX('I', 7, AF10)>, /* SAI2_FS_A */
+ <STM32_PINMUX('D', 13, AF10)>; /* SAI2_SCK_A */
+ slew-rate = <0>;
+ drive-push-pull;
+ bias-disable;
+ };
+ };
+
+ sai2a_sleep_pins_b: sai2a-sleep-3 {
+ pins {
+ pinmux = <STM32_PINMUX('I', 6, ANALOG)>, /* SAI2_SD_A */
+ <STM32_PINMUX('I', 7, ANALOG)>, /* SAI2_FS_A */
+ <STM32_PINMUX('D', 13, ANALOG)>; /* SAI2_SCK_A */
+ };
+ };
+
sai2b_pins_a: sai2b-0 {
pins1 {
pinmux = <STM32_PINMUX('E', 12, AF10)>, /* SAI2_SCK_B */
@@ -1118,6 +1171,19 @@
};
};
+ usart3_pins_a: usart3-0 {
+ pins1 {
+ pinmux = <STM32_PINMUX('B', 10, AF7)>; /* USART3_TX */
+ bias-disable;
+ drive-push-pull;
+ slew-rate = <0>;
+ };
+ pins2 {
+ pinmux = <STM32_PINMUX('B', 12, AF8)>; /* USART3_RX */
+ bias-disable;
+ };
+ };
+
uart4_pins_a: uart4-0 {
pins1 {
pinmux = <STM32_PINMUX('G', 11, AF6)>; /* UART4_TX */
@@ -1158,6 +1224,32 @@
bias-disable;
};
};
+
+ uart8_pins_a: uart8-0 {
+ pins1 {
+ pinmux = <STM32_PINMUX('E', 1, AF8)>; /* UART8_TX */
+ bias-disable;
+ drive-push-pull;
+ slew-rate = <0>;
+ };
+ pins2 {
+ pinmux = <STM32_PINMUX('E', 0, AF8)>; /* UART8_RX */
+ bias-disable;
+ };
+ };
+
+ usbotg_hs_pins_a: usbotg-hs-0 {
+ pins {
+ pinmux = <STM32_PINMUX('A', 10, ANALOG)>; /* OTG_ID */
+ };
+ };
+
+ usbotg_fs_dp_dm_pins_a: usbotg-fs-dp-dm-0 {
+ pins {
+ pinmux = <STM32_PINMUX('A', 11, ANALOG)>, /* OTG_FS_DM */
+ <STM32_PINMUX('A', 12, ANALOG)>; /* OTG_FS_DP */
+ };
+ };
};
&pinctrl_z {
diff --git a/arch/arm/dts/stm32mp151.dtsi b/arch/arm/dts/stm32mp151.dtsi
index f185639..75d2c0d 100644
--- a/arch/arm/dts/stm32mp151.dtsi
+++ b/arch/arm/dts/stm32mp151.dtsi
@@ -17,6 +17,7 @@
cpu0: cpu@0 {
compatible = "arm,cortex-a7";
+ clock-frequency = <650000000>;
device_type = "cpu";
reg = <0>;
};
@@ -490,6 +491,7 @@
resets = <&rcc I2C1_R>;
#address-cells = <1>;
#size-cells = <0>;
+ wakeup-source;
status = "disabled";
};
@@ -503,6 +505,7 @@
resets = <&rcc I2C2_R>;
#address-cells = <1>;
#size-cells = <0>;
+ wakeup-source;
status = "disabled";
};
@@ -516,6 +519,7 @@
resets = <&rcc I2C3_R>;
#address-cells = <1>;
#size-cells = <0>;
+ wakeup-source;
status = "disabled";
};
@@ -529,6 +533,7 @@
resets = <&rcc I2C5_R>;
#address-cells = <1>;
#size-cells = <0>;
+ wakeup-source;
status = "disabled";
};
@@ -966,6 +971,7 @@
<GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 47 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&rcc DMA1>;
+ resets = <&rcc DMA1_R>;
#dma-cells = <4>;
st,mem2mem;
dma-requests = <8>;
@@ -983,6 +989,7 @@
<GIC_SPI 69 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 70 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&rcc DMA2>;
+ resets = <&rcc DMA2_R>;
#dma-cells = <4>;
st,mem2mem;
dma-requests = <8>;
@@ -996,6 +1003,7 @@
dma-masters = <&dma1 &dma2>;
dma-channels = <16>;
clocks = <&rcc DMAMUX>;
+ resets = <&rcc DMAMUX_R>;
};
adc: adc@48003000 {
@@ -1051,7 +1059,7 @@
};
usbotg_hs: usb-otg@49000000 {
- compatible = "snps,dwc2";
+ compatible = "st,stm32mp15-hsotg", "snps,dwc2";
reg = <0x49000000 0x10000>;
clocks = <&rcc USBO_K>;
clock-names = "otg";
@@ -1296,6 +1304,7 @@
reg = <0x58000000 0x1000>;
interrupts = <GIC_SPI 122 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&rcc MDMA>;
+ resets = <&rcc MDMA_R>;
#dma-cells = <5>;
dma-channels = <32>;
dma-requests = <48>;
@@ -1495,6 +1504,7 @@
resets = <&rcc I2C4_R>;
#address-cells = <1>;
#size-cells = <0>;
+ wakeup-source;
status = "disabled";
};
@@ -1530,6 +1540,7 @@
resets = <&rcc I2C6_R>;
#address-cells = <1>;
#size-cells = <0>;
+ wakeup-source;
status = "disabled";
};
diff --git a/arch/arm/dts/stm32mp153.dtsi b/arch/arm/dts/stm32mp153.dtsi
index 2d759fc..6d9ab08 100644
--- a/arch/arm/dts/stm32mp153.dtsi
+++ b/arch/arm/dts/stm32mp153.dtsi
@@ -10,6 +10,7 @@
cpus {
cpu1: cpu@1 {
compatible = "arm,cortex-a7";
+ clock-frequency = <650000000>;
device_type = "cpu";
reg = <1>;
};
diff --git a/arch/arm/dts/stm32mp157c-ed1.dts b/arch/arm/dts/stm32mp157c-ed1.dts
index 05d5326..4fb7110 100644
--- a/arch/arm/dts/stm32mp157c-ed1.dts
+++ b/arch/arm/dts/stm32mp157c-ed1.dts
@@ -135,10 +135,12 @@
};
&i2c4 {
- pinctrl-names = "default";
+ pinctrl-names = "default", "sleep";
pinctrl-0 = <&i2c4_pins_a>;
+ pinctrl-1 = <&i2c4_pins_sleep_a>;
i2c-scl-rising-time-ns = <185>;
i2c-scl-falling-time-ns = <20>;
+ clock-frequency = <400000>;
status = "okay";
/* spare dmas for other usage */
/delete-property/dmas;
@@ -223,8 +225,6 @@
vdd_usb: ldo4 {
regulator-name = "vdd_usb";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
interrupts = <IT_CURLIM_LDO4 0>;
};
@@ -246,7 +246,6 @@
vref_ddr: vref_ddr {
regulator-name = "vref_ddr";
regulator-always-on;
- regulator-over-current-protection;
};
bst_out: boost {
@@ -318,7 +317,8 @@
pinctrl-0 = <&sdmmc1_b4_pins_a &sdmmc1_dir_pins_a>;
pinctrl-1 = <&sdmmc1_b4_od_pins_a &sdmmc1_dir_pins_a>;
pinctrl-2 = <&sdmmc1_b4_sleep_pins_a &sdmmc1_dir_sleep_pins_a>;
- broken-cd;
+ cd-gpios = <&gpiog 1 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>;
+ disable-wp;
st,sig-dir;
st,neg-edge;
st,use-ckin;
@@ -339,7 +339,7 @@
st,neg-edge;
bus-width = <8>;
vmmc-supply = <&v3v3>;
- vqmmc-supply = <&v3v3>;
+ vqmmc-supply = <&vdd>;
mmc-ddr-3_3v;
status = "okay";
};
diff --git a/arch/arm/dts/stm32mp157c-ev1.dts b/arch/arm/dts/stm32mp157c-ev1.dts
index 228e35e..8a4c7ff 100644
--- a/arch/arm/dts/stm32mp157c-ev1.dts
+++ b/arch/arm/dts/stm32mp157c-ev1.dts
@@ -174,8 +174,9 @@
};
&i2c2 {
- pinctrl-names = "default";
+ pinctrl-names = "default", "sleep";
pinctrl-0 = <&i2c2_pins_a>;
+ pinctrl-1 = <&i2c2_pins_sleep_a>;
i2c-scl-rising-time-ns = <185>;
i2c-scl-falling-time-ns = <20>;
status = "okay";
@@ -210,7 +211,7 @@
interrupt-parent = <&gpioi>;
vdd-supply = <&v3v3>;
- stmfx_pinctrl: stmfx-pin-controller {
+ stmfx_pinctrl: pinctrl {
compatible = "st,stmfx-0300-pinctrl";
gpio-controller;
#gpio-cells = <2>;
@@ -218,7 +219,7 @@
#interrupt-cells = <2>;
gpio-ranges = <&stmfx_pinctrl 0 0 24>;
- joystick_pins: joystick {
+ joystick_pins: joystick-pins {
pins = "gpio0", "gpio1", "gpio2", "gpio3", "gpio4";
bias-pull-down;
};
@@ -227,8 +228,9 @@
};
&i2c5 {
- pinctrl-names = "default";
+ pinctrl-names = "default", "sleep";
pinctrl-0 = <&i2c5_pins_a>;
+ pinctrl-1 = <&i2c5_pins_sleep_a>;
i2c-scl-rising-time-ns = <185>;
i2c-scl-falling-time-ns = <20>;
status = "okay";
@@ -353,7 +355,8 @@
};
&usbotg_hs {
- dr_mode = "peripheral";
+ pinctrl-0 = <&usbotg_hs_pins_a>;
+ pinctrl-names = "default";
phys = <&usbphyc_port1 0>;
phy-names = "usb2-phy";
status = "okay";
diff --git a/arch/arm/dts/stm32mp15xx-dhcom.dtsi b/arch/arm/dts/stm32mp15xx-dhcom.dtsi
index d8a255b..b3f4cb4 100644
--- a/arch/arm/dts/stm32mp15xx-dhcom.dtsi
+++ b/arch/arm/dts/stm32mp15xx-dhcom.dtsi
@@ -269,7 +269,8 @@
pinctrl-0 = <&sdmmc1_b4_pins_a &sdmmc1_dir_pins_a>;
pinctrl-1 = <&sdmmc1_b4_od_pins_a &sdmmc1_dir_pins_a>;
pinctrl-2 = <&sdmmc1_b4_sleep_pins_a &sdmmc1_dir_sleep_pins_a>;
- broken-cd;
+ cd-gpios = <&gpioi 8 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>;
+ disable-wp;
st,sig-dir;
st,neg-edge;
st,use-ckin;
diff --git a/arch/arm/dts/stm32mp15xx-dhcor-io3v3.dtsi b/arch/arm/dts/stm32mp15xx-dhcor-io3v3.dtsi
index 248fc45..64299df 100644
--- a/arch/arm/dts/stm32mp15xx-dhcor-io3v3.dtsi
+++ b/arch/arm/dts/stm32mp15xx-dhcor-io3v3.dtsi
@@ -40,10 +40,6 @@
#interrupt-cells = <2>;
status = "okay";
- st,main-control-register = <0x04>;
- st,vin-control-register = <0xc0>;
- st,usb-control-register = <0x30>;
-
regulators {
compatible = "st,stpmic1-regulators";
@@ -78,7 +74,6 @@
regulator-min-microvolt = <2900000>;
regulator-max-microvolt = <2900000>;
regulator-always-on;
- st,mask_reset;
regulator-initial-mode = <0>;
regulator-over-current-protection;
};
@@ -118,8 +113,6 @@
vdd_usb: ldo4 {
regulator-name = "vdd_usb";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
interrupts = <IT_CURLIM_LDO4 0>;
interrupt-parent = <&pmic>;
};
@@ -145,7 +138,6 @@
vref_ddr: vref_ddr {
regulator-name = "vref_ddr";
regulator-always-on;
- regulator-over-current-protection;
};
bst_out: boost {
diff --git a/arch/arm/dts/stm32mp15xx-dkx.dtsi b/arch/arm/dts/stm32mp15xx-dkx.dtsi
index 9ce10a5..812e370 100644
--- a/arch/arm/dts/stm32mp15xx-dkx.dtsi
+++ b/arch/arm/dts/stm32mp15xx-dkx.dtsi
@@ -221,10 +221,12 @@
};
&i2c4 {
- pinctrl-names = "default";
+ pinctrl-names = "default", "sleep";
pinctrl-0 = <&i2c4_pins_a>;
+ pinctrl-1 = <&i2c4_pins_sleep_a>;
i2c-scl-rising-time-ns = <185>;
i2c-scl-falling-time-ns = <20>;
+ clock-frequency = <400000>;
status = "okay";
/* spare dmas for other usage */
/delete-property/dmas;
@@ -327,8 +329,6 @@
vdd_usb: ldo4 {
regulator-name = "vdd_usb";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
interrupts = <IT_CURLIM_LDO4 0>;
};
@@ -351,7 +351,6 @@
vref_ddr: vref_ddr {
regulator-name = "vref_ddr";
regulator-always-on;
- regulator-over-current-protection;
};
bst_out: boost {
@@ -502,7 +501,8 @@
pinctrl-0 = <&sdmmc1_b4_pins_a>;
pinctrl-1 = <&sdmmc1_b4_od_pins_a>;
pinctrl-2 = <&sdmmc1_b4_sleep_pins_a>;
- broken-cd;
+ cd-gpios = <&gpiob 7 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>;
+ disable-wp;
st,neg-edge;
bus-width = <4>;
vmmc-supply = <&v3v3>;