sunxi: A64: Update .dts/.dtsi files
Update the .dts/.dtsi file from the Linux sunxi/dt64-for-4.20 tree:
commit 679294497be31596e1c9c61507746d72b6b05f26
Author: Rodrigo Exterckötter Tjäder <rodrigo@tjader.xyz>
Date: Wed Sep 26 19:48:24 2018 +0000
arm64: dts: allwinner: a64: a64-olinuxino: set the PHY TX delay
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
diff --git a/arch/arm/dts/sun50i-a64-amarula-relic.dts b/arch/arm/dts/sun50i-a64-amarula-relic.dts
index f3b4e93..6cb2b7f 100644
--- a/arch/arm/dts/sun50i-a64-amarula-relic.dts
+++ b/arch/arm/dts/sun50i-a64-amarula-relic.dts
@@ -22,11 +22,11 @@
stdout-path = "serial0:115200n8";
};
- reg_vcc3v3: vcc3v3 {
- compatible = "regulator-fixed";
- regulator-name = "vcc3v3";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
+ wifi_pwrseq: wifi-pwrseq {
+ compatible = "mmc-pwrseq-simple";
+ clocks = <&rtc 1>;
+ clock-names = "ext_clock";
+ reset-gpios = <&r_pio 0 2 GPIO_ACTIVE_LOW>; /* WL-PMU-EN: PL2 */
};
};
@@ -34,10 +34,34 @@
status = "okay";
};
+&mmc1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc1_pins>;
+ vmmc-supply = <®_dcdc1>;
+ /*
+ * Schematic shows both dldo4 and eldo1 connected for vcc-io-wifi, but
+ * dldo4 connection shows DNP(Do Not Populate) and eldo1 connected with
+ * 0Ohm register to vcc-io-wifi so eldo1 is used.
+ */
+ vqmmc-supply = <®_eldo1>;
+ mmc-pwrseq = <&wifi_pwrseq>;
+ bus-width = <4>;
+ non-removable;
+ status = "okay";
+
+ brcmf: wifi@1 {
+ reg = <1>;
+ compatible = "brcm,bcm4329-fmac";
+ interrupt-parent = <&r_pio>;
+ interrupts = <0 3 IRQ_TYPE_LEVEL_LOW>; /* WL-WAKE-AP: PL3 */
+ interrupt-names = "host-wake";
+ };
+};
+
&mmc2 {
pinctrl-names = "default";
pinctrl-0 = <&mmc2_pins>;
- vmmc-supply = <®_vcc3v3>;
+ vmmc-supply = <®_dcdc1>;
bus-width = <8>;
non-removable;
cap-mmc-hw-reset;
@@ -48,9 +72,138 @@
status = "okay";
};
+&r_rsb {
+ status = "okay";
+
+ axp803: pmic@3a3 {
+ compatible = "x-powers,axp803";
+ reg = <0x3a3>;
+ interrupt-parent = <&r_intc>;
+ interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+ x-powers,drive-vbus-en; /* set N_VBUSEN as output pin */
+ };
+};
+
+#include "axp803.dtsi"
+
+®_aldo1 {
+ regulator-always-on;
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ regulator-name = "avdd-csi";
+};
+
+®_aldo2 {
+ regulator-always-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-pl";
+};
+
+®_aldo3 {
+ regulator-always-on;
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-name = "vcc-pll-avcc";
+};
+
+®_dcdc1 {
+ regulator-always-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-3v3";
+};
+
+®_dcdc2 {
+ regulator-always-on;
+ regulator-min-microvolt = <1040000>;
+ regulator-max-microvolt = <1300000>;
+ regulator-name = "vdd-cpux";
+};
+
+/* DCDC3 is polyphased with DCDC2 */
+
+®_dcdc5 {
+ regulator-always-on;
+ regulator-min-microvolt = <1500000>;
+ regulator-max-microvolt = <1500000>;
+ regulator-name = "vcc-dram";
+};
+
+®_dcdc6 {
+ regulator-always-on;
+ regulator-min-microvolt = <1100000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-name = "vdd-sys";
+};
+
+®_dldo1 {
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-hdmi-dsi-sensor";
+};
+
+®_dldo2 {
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-mipi";
+};
+
+®_dldo3 {
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ regulator-name = "dovdd-csi";
+};
+
+®_dldo4 {
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-wifi-io";
+};
+
+®_drivevbus {
+ regulator-name = "usb0-vbus";
+ status = "okay";
+};
+
+®_eldo1 {
+ regulator-always-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-name = "cpvdd";
+};
+
+®_eldo3 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-name = "dvdd-csi";
+};
+
+®_fldo1 {
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-name = "vcc-1v2-hsic";
+};
+
+/*
+ * The A64 chip cannot work without this regulator off, although
+ * it seems to be only driving the AR100 core.
+ * Maybe we don't still know well about CPUs domain.
+ */
+®_fldo2 {
+ regulator-always-on;
+ regulator-min-microvolt = <1100000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-name = "vdd-cpus";
+};
+
+®_rtc_ldo {
+ regulator-name = "vcc-rtc";
+};
+
&uart0 {
pinctrl-names = "default";
- pinctrl-0 = <&uart0_pins_a>;
+ pinctrl-0 = <&uart0_pb_pins>;
status = "okay";
};
@@ -61,5 +214,6 @@
&usbphy {
usb0_id_det-gpios = <&pio 7 9 GPIO_ACTIVE_HIGH>; /* PH9 */
+ usb0_vbus-supply = <®_drivevbus>;
status = "okay";
};
diff --git a/arch/arm/dts/sun50i-a64-bananapi-m64.dts b/arch/arm/dts/sun50i-a64-bananapi-m64.dts
index 0716b14..ef1c904 100644
--- a/arch/arm/dts/sun50i-a64-bananapi-m64.dts
+++ b/arch/arm/dts/sun50i-a64-bananapi-m64.dts
@@ -60,6 +60,17 @@
stdout-path = "serial0:115200n8";
};
+ hdmi-connector {
+ compatible = "hdmi-connector";
+ type = "a";
+
+ port {
+ hdmi_con_in: endpoint {
+ remote-endpoint = <&hdmi_out_con>;
+ };
+ };
+ };
+
leds {
compatible = "gpio-leds";
@@ -86,6 +97,10 @@
};
};
+&de {
+ status = "okay";
+};
+
&ehci0 {
status = "okay";
};
@@ -103,6 +118,17 @@
status = "okay";
};
+&hdmi {
+ hvcc-supply = <®_dldo1>;
+ status = "okay";
+};
+
+&hdmi_out {
+ hdmi_out_con: endpoint {
+ remote-endpoint = <&hdmi_con_in>;
+ };
+};
+
&i2c1 {
pinctrl-names = "default";
pinctrl-0 = <&i2c1_pins>;
@@ -151,7 +177,7 @@
&mmc2 {
pinctrl-names = "default";
- pinctrl-0 = <&mmc2_pins>;
+ pinctrl-0 = <&mmc2_pins>, <&mmc2_ds_pin>;
vmmc-supply = <®_dcdc1>;
bus-width = <8>;
non-removable;
@@ -296,9 +322,13 @@
regulator-name = "vcc-rtc";
};
+&simplefb_hdmi {
+ vcc-hdmi-supply = <®_dldo1>;
+};
+
&uart0 {
pinctrl-names = "default";
- pinctrl-0 = <&uart0_pins_a>;
+ pinctrl-0 = <&uart0_pb_pins>;
status = "okay";
};
diff --git a/arch/arm/dts/sun50i-a64-nanopi-a64.dts b/arch/arm/dts/sun50i-a64-nanopi-a64.dts
index e2dce48..31884db 100644
--- a/arch/arm/dts/sun50i-a64-nanopi-a64.dts
+++ b/arch/arm/dts/sun50i-a64-nanopi-a64.dts
@@ -51,12 +51,44 @@
compatible = "friendlyarm,nanopi-a64", "allwinner,sun50i-a64";
aliases {
+ ethernet0 = &emac;
serial0 = &uart0;
};
chosen {
stdout-path = "serial0:115200n8";
};
+
+ hdmi-connector {
+ compatible = "hdmi-connector";
+ type = "a";
+
+ port {
+ hdmi_con_in: endpoint {
+ remote-endpoint = <&hdmi_out_con>;
+ };
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ blue {
+ label = "nanopi-a64:blue:status";
+ gpios = <&pio 3 24 GPIO_ACTIVE_LOW>; /* PD24 */
+ };
+ };
+
+ wifi_pwrseq: wifi_pwrseq {
+ compatible = "mmc-pwrseq-simple";
+ clocks = <&rtc 1>;
+ clock-names = "ext_clock";
+ reset-gpios = <&r_pio 0 2 GPIO_ACTIVE_LOW>; /* PL2 */
+ };
+};
+
+&de {
+ status = "okay";
};
&ehci0 {
@@ -67,6 +99,26 @@
status = "okay";
};
+&emac {
+ pinctrl-names = "default";
+ pinctrl-0 = <&rgmii_pins>;
+ phy-mode = "rgmii";
+ phy-handle = <&ext_rgmii_phy>;
+ phy-supply = <®_dcdc1>;
+ status = "okay";
+};
+
+&hdmi {
+ hvcc-supply = <®_dldo1>;
+ status = "okay";
+};
+
+&hdmi_out {
+ hdmi_out_con: endpoint {
+ remote-endpoint = <&hdmi_con_in>;
+ };
+};
+
/* i2c1 connected with gpio headers like pine64, bananapi */
&i2c1 {
pinctrl-names = "default";
@@ -78,6 +130,13 @@
bias-pull-up;
};
+&mdio {
+ ext_rgmii_phy: ethernet-phy@1 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <7>;
+ };
+};
+
&mmc0 {
pinctrl-names = "default";
pinctrl-0 = <&mmc0_pins>;
@@ -88,6 +147,24 @@
status = "okay";
};
+&mmc1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc1_pins>;
+ vmmc-supply = <®_dcdc1>;
+ vqmmc-supply = <®_dldo4>;
+ mmc-pwrseq = <&wifi_pwrseq>;
+ bus-width = <4>;
+ non-removable;
+ status = "okay";
+
+ rtl8189etv: wifi@1 {
+ reg = <1>;
+ interrupt-parent = <&r_pio>;
+ interrupts = <0 3 IRQ_TYPE_LEVEL_LOW>; /* PL3 */
+ interrupt-names = "host-wake";
+ };
+};
+
&ohci0 {
status = "okay";
};
@@ -125,9 +202,9 @@
®_dcdc1 {
regulator-always-on;
- regulator-min-microvolt = <3000000>;
- regulator-max-microvolt = <3000000>;
- regulator-name = "vcc-3v";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-3v3";
};
®_dcdc2 {
@@ -195,9 +272,13 @@
regulator-name = "vcc-rtc";
};
+&simplefb_hdmi {
+ vcc-hdmi-supply = <®_dldo1>;
+};
+
&uart0 {
pinctrl-names = "default";
- pinctrl-0 = <&uart0_pins_a>;
+ pinctrl-0 = <&uart0_pb_pins>;
status = "okay";
};
diff --git a/arch/arm/dts/sun50i-a64-olinuxino.dts b/arch/arm/dts/sun50i-a64-olinuxino.dts
index 3b3081b..f7a4bcc 100644
--- a/arch/arm/dts/sun50i-a64-olinuxino.dts
+++ b/arch/arm/dts/sun50i-a64-olinuxino.dts
@@ -51,6 +51,7 @@
compatible = "olimex,a64-olinuxino", "allwinner,sun50i-a64";
aliases {
+ ethernet0 = &emac;
serial0 = &uart0;
};
@@ -58,12 +59,74 @@
stdout-path = "serial0:115200n8";
};
+ hdmi-connector {
+ compatible = "hdmi-connector";
+ type = "a";
+
+ port {
+ hdmi_con_in: endpoint {
+ remote-endpoint = <&hdmi_out_con>;
+ };
+ };
+ };
+
+ reg_usb1_vbus: usb1-vbus {
+ compatible = "regulator-fixed";
+ regulator-name = "usb1-vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-boot-on;
+ enable-active-high;
+ gpio = <&pio 6 9 GPIO_ACTIVE_HIGH>; /* PG9 */
+ status = "okay";
+ };
+
wifi_pwrseq: wifi_pwrseq {
compatible = "mmc-pwrseq-simple";
reset-gpios = <&r_pio 0 2 GPIO_ACTIVE_LOW>; /* PL2 */
};
};
+&de {
+ status = "okay";
+};
+
+&ehci0 {
+ status = "okay";
+};
+
+&ehci1 {
+ status = "okay";
+};
+
+&emac {
+ pinctrl-names = "default";
+ pinctrl-0 = <&rgmii_pins>;
+ phy-mode = "rgmii";
+ phy-handle = <&ext_rgmii_phy>;
+ phy-supply = <®_dcdc1>;
+ allwinner,tx-delay-ps = <600>;
+ status = "okay";
+};
+
+&hdmi {
+ hvcc-supply = <®_dldo1>;
+ status = "okay";
+};
+
+&hdmi_out {
+ hdmi_out_con: endpoint {
+ remote-endpoint = <&hdmi_con_in>;
+ };
+};
+
+&mdio {
+ ext_rgmii_phy: ethernet-phy@1 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <1>;
+ };
+};
+
&mmc0 {
pinctrl-names = "default";
pinctrl-0 = <&mmc0_pins>;
@@ -92,6 +155,14 @@
};
};
+&ohci0 {
+ status = "okay";
+};
+
+&ohci1 {
+ status = "okay";
+};
+
&r_rsb {
status = "okay";
@@ -100,6 +171,7 @@
reg = <0x3a3>;
interrupt-parent = <&r_intc>;
interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+ x-powers,drive-vbus-en; /* set N_VBUSEN as output pin */
};
};
@@ -142,10 +214,14 @@
/* DCDC3 is polyphased with DCDC2 */
+/*
+ * The board uses DDR3L DRAM chips. 1.36V is the closest to the nominal
+ * 1.35V that the PMIC can drive.
+ */
®_dcdc5 {
regulator-always-on;
- regulator-min-microvolt = <1500000>;
- regulator-max-microvolt = <1500000>;
+ regulator-min-microvolt = <1360000>;
+ regulator-max-microvolt = <1360000>;
regulator-name = "vcc-ddr3";
};
@@ -180,6 +256,11 @@
regulator-name = "vcc-wifi-io";
};
+®_drivevbus {
+ regulator-name = "usb0-vbus";
+ status = "okay";
+};
+
®_eldo1 {
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
@@ -214,8 +295,24 @@
regulator-name = "vcc-rtc";
};
+&simplefb_hdmi {
+ vcc-hdmi-supply = <®_dldo1>;
+};
+
&uart0 {
pinctrl-names = "default";
- pinctrl-0 = <&uart0_pins_a>;
+ pinctrl-0 = <&uart0_pb_pins>;
status = "okay";
};
+
+&usb_otg {
+ dr_mode = "otg";
+ status = "okay";
+};
+
+&usbphy {
+ status = "okay";
+ usb0_id_det-gpios = <&pio 7 9 GPIO_ACTIVE_HIGH>; /* PH9 */
+ usb0_vbus-supply = <®_drivevbus>;
+ usb1_vbus-supply = <®_usb1_vbus>;
+};
diff --git a/arch/arm/dts/sun50i-a64-orangepi-win.dts b/arch/arm/dts/sun50i-a64-orangepi-win.dts
index bf42690..b0c64f7 100644
--- a/arch/arm/dts/sun50i-a64-orangepi-win.dts
+++ b/arch/arm/dts/sun50i-a64-orangepi-win.dts
@@ -1,5 +1,6 @@
/*
* Copyright (C) 2017 Jagan Teki <jteki@openedev.com>
+ * Copyright (C) 2017-2018 Samuel Holland <samuel@sholland.org>
*
* This file is dual-licensed: you can use it either under the terms
* of the GPL or the X11 license, at your option. Note that this dual
@@ -51,23 +52,127 @@
compatible = "xunlong,orangepi-win", "allwinner,sun50i-a64";
aliases {
+ ethernet0 = &emac;
serial0 = &uart0;
+ serial1 = &uart1;
+ serial2 = &uart2;
+ serial3 = &uart3;
+ serial4 = &uart4;
};
chosen {
stdout-path = "serial0:115200n8";
};
+
+ hdmi-connector {
+ compatible = "hdmi-connector";
+ type = "a";
+
+ port {
+ hdmi_con_in: endpoint {
+ remote-endpoint = <&hdmi_out_con>;
+ };
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ status {
+ label = "orangepi:green:status";
+ gpios = <&pio 7 11 GPIO_ACTIVE_HIGH>; /* PH11 */
+ };
+ };
+
+ reg_gmac_3v3: gmac-3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "gmac-3v3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ enable-active-high;
+ gpio = <&pio 3 14 GPIO_ACTIVE_HIGH>; /* PD14 */
+ status = "okay";
+ };
+
+ reg_usb1_vbus: usb1-vbus {
+ compatible = "regulator-fixed";
+ regulator-name = "usb1-vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-boot-on;
+ enable-active-high;
+ gpio = <&pio 3 7 GPIO_ACTIVE_HIGH>; /* PD7 */
+ status = "okay";
+ };
+
+ wifi_pwrseq: wifi_pwrseq {
+ compatible = "mmc-pwrseq-simple";
+ reset-gpios = <&r_pio 0 8 GPIO_ACTIVE_LOW>; /* PL8 */
+ };
+};
+
+&de {
+ status = "okay";
+};
+
+&ehci0 {
+ status = "okay";
};
&ehci1 {
status = "okay";
};
+&emac {
+ pinctrl-names = "default";
+ pinctrl-0 = <&rgmii_pins>;
+ phy-mode = "rgmii";
+ phy-handle = <&ext_rgmii_phy>;
+ phy-supply = <®_gmac_3v3>;
+ status = "okay";
+};
+
+&hdmi {
+ hvcc-supply = <®_dldo1>;
+ status = "okay";
+};
+
+&hdmi_out {
+ hdmi_out_con: endpoint {
+ remote-endpoint = <&hdmi_con_in>;
+ };
+};
+
+&mdio {
+ ext_rgmii_phy: ethernet-phy@1 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <1>;
+ };
+};
+
&mmc0 {
pinctrl-names = "default";
pinctrl-0 = <&mmc0_pins>;
vmmc-supply = <®_dcdc1>;
- cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>;
+ cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */
+ disable-wp;
+ bus-width = <4>;
+ status = "okay";
+};
+
+&mmc1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc1_pins>;
+ vmmc-supply = <®_dldo2>;
+ vqmmc-supply = <®_dldo4>;
+ mmc-pwrseq = <&wifi_pwrseq>;
+ bus-width = <4>;
+ non-removable;
+ status = "okay";
+};
+
+&ohci0 {
status = "okay";
};
@@ -89,9 +194,8 @@
#include "axp803.dtsi"
®_aldo1 {
- regulator-always-on;
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <3300000>;
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
regulator-name = "afvcc-csi";
};
@@ -163,12 +267,23 @@
regulator-name = "vcc-wifi-io";
};
+®_drivevbus {
+ regulator-name = "usb0-vbus";
+ status = "okay";
+};
+
®_eldo1 {
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
regulator-name = "cpvdd";
};
+®_eldo3 {
+ regulator-min-microvolt = <1500000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-name = "dvdd-csi";
+};
+
®_fldo1 {
regulator-min-microvolt = <1200000>;
regulator-max-microvolt = <1200000>;
@@ -191,13 +306,65 @@
regulator-name = "vcc-rtc";
};
+&simplefb_hdmi {
+ vcc-hdmi-supply = <®_dldo1>;
+};
+
+&spi0 {
+ status = "okay";
+
+ spi-flash@0 {
+ compatible = "mxicy,mx25l1606e", "jedec,spi-nor";
+ reg = <0>;
+ spi-max-frequency = <80000000>;
+ m25p,fast-read;
+ status = "okay";
+ };
+};
+
+/* On debug connector */
&uart0 {
pinctrl-names = "default";
- pinctrl-0 = <&uart0_pins_a>;
+ pinctrl-0 = <&uart0_pb_pins>;
+ status = "okay";
+};
+
+/* Bluetooth */
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart1_pins>, <&uart1_rts_cts_pins>;
+ status = "okay";
+};
+
+/* On Pi-2 connector, RTS/CTS optional */
+&uart2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart2_pins>;
+ status = "disabled";
+};
+
+/* On Pi-2 connector, RTS/CTS optional */
+&uart3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart3_pins>;
+ status = "disabled";
+};
+
+/* On Pi-2 connector (labeled for SPI1), RTS/CTS optional */
+&uart4 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart4_pins>;
+ status = "disabled";
+};
+
+&usb_otg {
+ dr_mode = "otg";
status = "okay";
};
&usbphy {
+ usb0_id_det-gpios = <&pio 7 9 GPIO_ACTIVE_HIGH>; /* PH9 */
+ usb0_vbus-supply = <®_drivevbus>;
+ usb1_vbus-supply = <®_usb1_vbus>;
status = "okay";
};
-
diff --git a/arch/arm/dts/sun50i-a64-pine64.dts b/arch/arm/dts/sun50i-a64-pine64.dts
index a758257..c077b6c 100644
--- a/arch/arm/dts/sun50i-a64-pine64.dts
+++ b/arch/arm/dts/sun50i-a64-pine64.dts
@@ -62,6 +62,21 @@
chosen {
stdout-path = "serial0:115200n8";
};
+
+ hdmi-connector {
+ compatible = "hdmi-connector";
+ type = "a";
+
+ port {
+ hdmi_con_in: endpoint {
+ remote-endpoint = <&hdmi_out_con>;
+ };
+ };
+ };
+};
+
+&de {
+ status = "okay";
};
&ehci0 {
@@ -82,6 +97,17 @@
};
+&hdmi {
+ hvcc-supply = <®_dldo1>;
+ status = "okay";
+};
+
+&hdmi_out {
+ hdmi_out_con: endpoint {
+ remote-endpoint = <&hdmi_con_in>;
+ };
+};
+
&i2c1 {
pinctrl-names = "default";
pinctrl-0 = <&i2c1_pins>;
@@ -229,6 +255,10 @@
regulator-name = "vcc-rtc";
};
+&simplefb_hdmi {
+ vcc-hdmi-supply = <®_dldo1>;
+};
+
/* On Euler connector */
&spdif {
status = "disabled";
@@ -237,7 +267,7 @@
/* On Exp and Euler connectors */
&uart0 {
pinctrl-names = "default";
- pinctrl-0 = <&uart0_pins_a>;
+ pinctrl-0 = <&uart0_pb_pins>;
status = "okay";
};
diff --git a/arch/arm/dts/sun50i-a64-sopine-baseboard.dts b/arch/arm/dts/sun50i-a64-sopine-baseboard.dts
index abe179d..53fcc90 100644
--- a/arch/arm/dts/sun50i-a64-sopine-baseboard.dts
+++ b/arch/arm/dts/sun50i-a64-sopine-baseboard.dts
@@ -61,6 +61,17 @@
stdout-path = "serial0:115200n8";
};
+ hdmi-connector {
+ compatible = "hdmi-connector";
+ type = "a";
+
+ port {
+ hdmi_con_in: endpoint {
+ remote-endpoint = <&hdmi_out_con>;
+ };
+ };
+ };
+
reg_vcc1v8: vcc1v8 {
compatible = "regulator-fixed";
regulator-name = "vcc1v8";
@@ -69,6 +80,10 @@
};
};
+&de {
+ status = "okay";
+};
+
&ehci0 {
status = "okay";
};
@@ -86,6 +101,17 @@
status = "okay";
};
+&hdmi {
+ hvcc-supply = <®_dldo1>;
+ status = "okay";
+};
+
+&hdmi_out {
+ hdmi_out_con: endpoint {
+ remote-endpoint = <&hdmi_con_in>;
+ };
+};
+
&mdio {
ext_rgmii_phy: ethernet-phy@1 {
compatible = "ethernet-phy-ieee802.3-c22";
@@ -134,9 +160,13 @@
regulator-name = "vcc-wifi";
};
+&simplefb_hdmi {
+ vcc-hdmi-supply = <®_dldo1>;
+};
+
&uart0 {
pinctrl-names = "default";
- pinctrl-0 = <&uart0_pins_a>;
+ pinctrl-0 = <&uart0_pb_pins>;
status = "okay";
};
diff --git a/arch/arm/dts/sun50i-a64-sopine.dtsi b/arch/arm/dts/sun50i-a64-sopine.dtsi
index 43418bd..6723b86 100644
--- a/arch/arm/dts/sun50i-a64-sopine.dtsi
+++ b/arch/arm/dts/sun50i-a64-sopine.dtsi
@@ -45,6 +45,8 @@
#include "sun50i-a64.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+
&mmc0 {
pinctrl-names = "default";
pinctrl-0 = <&mmc0_pins>;
@@ -52,6 +54,7 @@
non-removable;
disable-wp;
bus-width = <4>;
+ cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */
status = "okay";
};
@@ -66,6 +69,18 @@
};
};
+&spi0 {
+ status = "okay";
+
+ flash@0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "jedec,spi-nor";
+ reg = <0>;
+ spi-max-frequency = <40000000>;
+ };
+};
+
#include "axp803.dtsi"
®_aldo2 {
diff --git a/arch/arm/dts/sun50i-a64.dtsi b/arch/arm/dts/sun50i-a64.dtsi
index 7a08363..f3a66f8 100644
--- a/arch/arm/dts/sun50i-a64.dtsi
+++ b/arch/arm/dts/sun50i-a64.dtsi
@@ -43,9 +43,12 @@
*/
#include <dt-bindings/clock/sun50i-a64-ccu.h>
+#include <dt-bindings/clock/sun8i-de2.h>
#include <dt-bindings/clock/sun8i-r-ccu.h>
#include <dt-bindings/interrupt-controller/arm-gic.h>
#include <dt-bindings/reset/sun50i-a64-ccu.h>
+#include <dt-bindings/reset/sun8i-de2.h>
+#include <dt-bindings/reset/sun8i-r-ccu.h>
/ {
interrupt-parent = <&gic>;
@@ -57,17 +60,21 @@
#size-cells = <1>;
ranges;
-/*
- * The pipeline mixer0-lcd0 depends on clock CLK_MIXER0 from DE2 CCU.
- * However there is no support for this clock on A64 yet, so we depend
- * on the upstream clocks here to keep them (and thus CLK_MIXER0) up.
- */
simplefb_lcd: framebuffer-lcd {
compatible = "allwinner,simple-framebuffer",
"simple-framebuffer";
allwinner,pipeline = "mixer0-lcd0";
clocks = <&ccu CLK_TCON0>,
- <&ccu CLK_DE>, <&ccu CLK_BUS_DE>;
+ <&display_clocks CLK_MIXER0>;
+ status = "disabled";
+ };
+
+ simplefb_hdmi: framebuffer-hdmi {
+ compatible = "allwinner,simple-framebuffer",
+ "simple-framebuffer";
+ allwinner,pipeline = "mixer1-lcd1-hdmi";
+ clocks = <&display_clocks CLK_MIXER1>,
+ <&ccu CLK_TCON1>, <&ccu CLK_HDMI>;
status = "disabled";
};
};
@@ -81,6 +88,7 @@
device_type = "cpu";
reg = <0>;
enable-method = "psci";
+ next-level-cache = <&L2>;
};
cpu1: cpu@1 {
@@ -88,6 +96,7 @@
device_type = "cpu";
reg = <1>;
enable-method = "psci";
+ next-level-cache = <&L2>;
};
cpu2: cpu@2 {
@@ -95,6 +104,7 @@
device_type = "cpu";
reg = <2>;
enable-method = "psci";
+ next-level-cache = <&L2>;
};
cpu3: cpu@3 {
@@ -102,7 +112,20 @@
device_type = "cpu";
reg = <3>;
enable-method = "psci";
+ next-level-cache = <&L2>;
};
+
+ L2: l2-cache {
+ compatible = "cache";
+ cache-level = <2>;
+ };
+ };
+
+ de: display-engine {
+ compatible = "allwinner,sun50i-a64-display-engine";
+ allwinner,pipelines = <&mixer0>,
+ <&mixer1>;
+ status = "disabled";
};
osc24M: osc24M_clk {
@@ -168,10 +191,92 @@
#size-cells = <1>;
ranges;
+ de2@1000000 {
+ compatible = "allwinner,sun50i-a64-de2";
+ reg = <0x1000000 0x400000>;
+ allwinner,sram = <&de2_sram 1>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0 0x1000000 0x400000>;
+
+ display_clocks: clock@0 {
+ compatible = "allwinner,sun50i-a64-de2-clk";
+ reg = <0x0 0x100000>;
+ clocks = <&ccu CLK_DE>,
+ <&ccu CLK_BUS_DE>;
+ clock-names = "mod",
+ "bus";
+ resets = <&ccu RST_BUS_DE>;
+ #clock-cells = <1>;
+ #reset-cells = <1>;
+ };
+
+ mixer0: mixer@100000 {
+ compatible = "allwinner,sun50i-a64-de2-mixer-0";
+ reg = <0x100000 0x100000>;
+ clocks = <&display_clocks CLK_BUS_MIXER0>,
+ <&display_clocks CLK_MIXER0>;
+ clock-names = "bus",
+ "mod";
+ resets = <&display_clocks RST_MIXER0>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ mixer0_out: port@1 {
+ reg = <1>;
+
+ mixer0_out_tcon0: endpoint {
+ remote-endpoint = <&tcon0_in_mixer0>;
+ };
+ };
+ };
+ };
+
+ mixer1: mixer@200000 {
+ compatible = "allwinner,sun50i-a64-de2-mixer-1";
+ reg = <0x200000 0x100000>;
+ clocks = <&display_clocks CLK_BUS_MIXER1>,
+ <&display_clocks CLK_MIXER1>;
+ clock-names = "bus",
+ "mod";
+ resets = <&display_clocks RST_MIXER1>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ mixer1_out: port@1 {
+ reg = <1>;
+
+ mixer1_out_tcon1: endpoint {
+ remote-endpoint = <&tcon1_in_mixer1>;
+ };
+ };
+ };
+ };
+ };
+
syscon: syscon@1c00000 {
- compatible = "allwinner,sun50i-a64-system-controller",
- "syscon";
+ compatible = "allwinner,sun50i-a64-system-control";
reg = <0x01c00000 0x1000>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ sram_c: sram@18000 {
+ compatible = "mmio-sram";
+ reg = <0x00018000 0x28000>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0 0x00018000 0x28000>;
+
+ de2_sram: sram-section@0 {
+ compatible = "allwinner,sun50i-a64-sram-c";
+ reg = <0x0000 0x28000>;
+ };
+ };
};
dma: dma-controller@1c02000 {
@@ -185,6 +290,75 @@
#dma-cells = <1>;
};
+ tcon0: lcd-controller@1c0c000 {
+ compatible = "allwinner,sun50i-a64-tcon-lcd",
+ "allwinner,sun8i-a83t-tcon-lcd";
+ reg = <0x01c0c000 0x1000>;
+ interrupts = <GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_TCON0>, <&ccu CLK_TCON0>;
+ clock-names = "ahb", "tcon-ch0";
+ clock-output-names = "tcon-pixel-clock";
+ resets = <&ccu RST_BUS_TCON0>, <&ccu RST_BUS_LVDS>;
+ reset-names = "lcd", "lvds";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ tcon0_in: port@0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0>;
+
+ tcon0_in_mixer0: endpoint@0 {
+ reg = <0>;
+ remote-endpoint = <&mixer0_out_tcon0>;
+ };
+ };
+
+ tcon0_out: port@1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <1>;
+ };
+ };
+ };
+
+ tcon1: lcd-controller@1c0d000 {
+ compatible = "allwinner,sun50i-a64-tcon-tv",
+ "allwinner,sun8i-a83t-tcon-tv";
+ reg = <0x01c0d000 0x1000>;
+ interrupts = <GIC_SPI 87 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_TCON1>, <&ccu CLK_TCON1>;
+ clock-names = "ahb", "tcon-ch1";
+ resets = <&ccu RST_BUS_TCON1>;
+ reset-names = "lcd";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ tcon1_in: port@0 {
+ reg = <0>;
+
+ tcon1_in_mixer1: endpoint {
+ remote-endpoint = <&mixer1_out_tcon1>;
+ };
+ };
+
+ tcon1_out: port@1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <1>;
+
+ tcon1_out_hdmi: endpoint@1 {
+ reg = <1>;
+ remote-endpoint = <&hdmi_in_tcon1>;
+ };
+ };
+ };
+ };
+
mmc0: mmc@1c0f000 {
compatible = "allwinner,sun50i-a64-mmc";
reg = <0x01c0f000 0x1000>;
@@ -227,6 +401,11 @@
#size-cells = <0>;
};
+ sid: eeprom@1c14000 {
+ compatible = "allwinner,sun50i-a64-sid";
+ reg = <0x1c14000 0x400>;
+ };
+
usb_otg: usb@1c19000 {
compatible = "allwinner,sun8i-a33-musb";
reg = <0x01c19000 0x0400>;
@@ -356,7 +535,7 @@
};
mmc2_pins: mmc2-pins {
- pins = "PC1", "PC5", "PC6", "PC8", "PC9",
+ pins = "PC5", "PC6", "PC8", "PC9",
"PC10","PC11", "PC12", "PC13",
"PC14", "PC15", "PC16";
function = "mmc2";
@@ -364,6 +543,18 @@
bias-pull-up;
};
+ mmc2_ds_pin: mmc2-ds-pin {
+ pins = "PC1";
+ function = "mmc2";
+ drive-strength = <30>;
+ bias-pull-up;
+ };
+
+ pwm_pin: pwm_pin {
+ pins = "PD22";
+ function = "pwm";
+ };
+
rmii_pins: rmii_pins {
pins = "PD10", "PD11", "PD13", "PD14", "PD17",
"PD18", "PD19", "PD20", "PD22", "PD23";
@@ -394,7 +585,7 @@
function = "spi1";
};
- uart0_pins_a: uart0 {
+ uart0_pb_pins: uart0-pb-pins {
pins = "PB8", "PB9";
function = "uart0";
};
@@ -474,15 +665,6 @@
status = "disabled";
};
- pwm: pwm@1c21400 {
- compatible = "allwinner,sun50i-a64-pwm",
- "allwinner,sun5i-a13-pwm";
- reg = <0x01c21400 0x8>;
- clocks = <&osc24M>;
- #pwm-cells = <3>;
- status = "disabled";
- };
-
uart0: serial@1c28000 {
compatible = "snps,dw-apb-uart";
reg = <0x01c28000 0x400>;
@@ -617,8 +799,6 @@
clocks = <&ccu CLK_BUS_EMAC>;
clock-names = "stmmaceth";
status = "disabled";
- #address-cells = <1>;
- #size-cells = <0>;
mdio: mdio {
compatible = "snps,dwmac-mdio";
@@ -638,11 +818,69 @@
#interrupt-cells = <3>;
};
+ pwm: pwm@1c21400 {
+ compatible = "allwinner,sun50i-a64-pwm",
+ "allwinner,sun5i-a13-pwm";
+ reg = <0x01c21400 0x400>;
+ clocks = <&osc24M>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pwm_pin>;
+ #pwm-cells = <3>;
+ status = "disabled";
+ };
+
+ hdmi: hdmi@1ee0000 {
+ compatible = "allwinner,sun50i-a64-dw-hdmi",
+ "allwinner,sun8i-a83t-dw-hdmi";
+ reg = <0x01ee0000 0x10000>;
+ reg-io-width = <1>;
+ interrupts = <GIC_SPI 88 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_HDMI>, <&ccu CLK_HDMI_DDC>,
+ <&ccu CLK_HDMI>;
+ clock-names = "iahb", "isfr", "tmds";
+ resets = <&ccu RST_BUS_HDMI1>;
+ reset-names = "ctrl";
+ phys = <&hdmi_phy>;
+ phy-names = "hdmi-phy";
+ status = "disabled";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ hdmi_in: port@0 {
+ reg = <0>;
+
+ hdmi_in_tcon1: endpoint {
+ remote-endpoint = <&tcon1_out_hdmi>;
+ };
+ };
+
+ hdmi_out: port@1 {
+ reg = <1>;
+ };
+ };
+ };
+
+ hdmi_phy: hdmi-phy@1ef0000 {
+ compatible = "allwinner,sun50i-a64-hdmi-phy";
+ reg = <0x01ef0000 0x10000>;
+ clocks = <&ccu CLK_BUS_HDMI>, <&ccu CLK_HDMI_DDC>,
+ <&ccu 7>;
+ clock-names = "bus", "mod", "pll-0";
+ resets = <&ccu RST_BUS_HDMI0>;
+ reset-names = "phy";
+ #phy-cells = <0>;
+ };
+
rtc: rtc@1f00000 {
compatible = "allwinner,sun6i-a31-rtc";
reg = <0x01f00000 0x54>;
interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>;
+ clock-output-names = "rtc-osc32k", "rtc-osc32k-out";
+ clocks = <&osc32k>;
+ #clock-cells = <1>;
};
r_intc: interrupt-controller@1f00c00 {
@@ -664,6 +902,29 @@
#reset-cells = <1>;
};
+ r_i2c: i2c@1f02400 {
+ compatible = "allwinner,sun50i-a64-i2c",
+ "allwinner,sun6i-a31-i2c";
+ reg = <0x01f02400 0x400>;
+ interrupts = <GIC_SPI 44 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&r_ccu CLK_APB0_I2C>;
+ resets = <&r_ccu RST_APB0_I2C>;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ r_pwm: pwm@1f03800 {
+ compatible = "allwinner,sun50i-a64-pwm",
+ "allwinner,sun5i-a13-pwm";
+ reg = <0x01f03800 0x400>;
+ clocks = <&osc24M>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&r_pwm_pin>;
+ #pwm-cells = <3>;
+ status = "disabled";
+ };
+
r_pio: pinctrl@1f02c00 {
compatible = "allwinner,sun50i-a64-r-pinctrl";
reg = <0x01f02c00 0x400>;
@@ -675,6 +936,16 @@
interrupt-controller;
#interrupt-cells = <3>;
+ r_i2c_pl89_pins: r-i2c-pl89-pins {
+ pins = "PL8", "PL9";
+ function = "s_i2c";
+ };
+
+ r_pwm_pin: pwm {
+ pins = "PL10";
+ function = "s_pwm";
+ };
+
r_rsb_pins: rsb {
pins = "PL0", "PL1";
function = "s_rsb";