pcm051: Add support for Phytec phyCORE-AM335x
The board is named pcm051 and has this hardware:
SOC: TI AM3359
DDR3-RAM: 2x MT41J256M8HX-15EIT:D 512MiB
ETH 1: LAN8710AI
SPI-Flash: W25Q64BVSSIG
RTC: RV-4162-C7
I2C-EEPROM: CAT32WC32
NAND: MT29F4G08_VFPGA63
PMIC: TPS65910A3
LCD
Supported:
UART 1
MMC/SD
ETH 1
USB
I2C
SPI
Not yet supported:
NAND
RTC
LCD
Signed-off-by: Lars Poeschel <poeschel@lemonage.de>
[trini: Add #define CONFIG_PHY_ADDR 0 to config]
Signed-off-by: Tom Rini <trini@ti.com>
diff --git a/board/phytec/pcm051/Makefile b/board/phytec/pcm051/Makefile
new file mode 100644
index 0000000..67a87a1
--- /dev/null
+++ b/board/phytec/pcm051/Makefile
@@ -0,0 +1,46 @@
+#
+# Makefile
+#
+# Copyright (C) 2011 Texas Instruments Incorporated - http://www.ti.com/
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed "as is" WITHOUT ANY WARRANTY of any
+# kind, whether express or implied; without even the implied warranty
+# of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+# GNU General Public License for more details.
+#
+
+include $(TOPDIR)/config.mk
+
+LIB = $(obj)lib$(BOARD).o
+
+ifdef CONFIG_SPL_BUILD
+COBJS := mux.o
+endif
+
+COBJS += board.o
+SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c)
+OBJS := $(addprefix $(obj),$(COBJS))
+SOBJS := $(addprefix $(obj),$(SOBJS))
+
+$(LIB): $(obj).depend $(OBJS) $(SOBJS)
+ $(call cmd_link_o_target, $(OBJS) $(SOBJS))
+
+clean:
+ rm -f $(SOBJS) $(OBJS)
+
+distclean: clean
+ rm -f $(LIB) core *.bak $(obj).depend
+
+#########################################################################
+
+# defines $(obj).depend target
+include $(SRCTREE)/rules.mk
+
+sinclude $(obj).depend
+
+#########################################################################
diff --git a/board/phytec/pcm051/board.c b/board/phytec/pcm051/board.c
new file mode 100644
index 0000000..55bc018
--- /dev/null
+++ b/board/phytec/pcm051/board.c
@@ -0,0 +1,266 @@
+/*
+ * board.c
+ *
+ * Board functions for Phytec phyCORE-AM335x (pcm051) based boards
+ *
+ * Copyright (C) 2013 Lemonage Software GmbH
+ * Author Lars Poeschel <poeschel@lemonage.de>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR /PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#include <common.h>
+#include <errno.h>
+#include <spl.h>
+#include <asm/arch/cpu.h>
+#include <asm/arch/hardware.h>
+#include <asm/arch/omap.h>
+#include <asm/arch/ddr_defs.h>
+#include <asm/arch/clock.h>
+#include <asm/arch/gpio.h>
+#include <asm/arch/mmc_host_def.h>
+#include <asm/arch/sys_proto.h>
+#include <asm/io.h>
+#include <asm/emif.h>
+#include <asm/gpio.h>
+#include <i2c.h>
+#include <miiphy.h>
+#include <cpsw.h>
+#include "board.h"
+
+DECLARE_GLOBAL_DATA_PTR;
+
+static struct wd_timer *wdtimer = (struct wd_timer *)WDT_BASE;
+#ifdef CONFIG_SPL_BUILD
+static struct uart_sys *uart_base = (struct uart_sys *)DEFAULT_UART_BASE;
+#endif
+
+/* MII mode defines */
+#define MII_MODE_ENABLE 0x0
+#define RGMII_MODE_ENABLE 0xA
+#define RMII_RGMII2_MODE_ENABLE 0x49
+
+static struct ctrl_dev *cdev = (struct ctrl_dev *)CTRL_DEVICE_BASE;
+
+/* UART defines */
+#ifdef CONFIG_SPL_BUILD
+#define UART_RESET (0x1 << 1)
+#define UART_CLK_RUNNING_MASK 0x1
+#define UART_SMART_IDLE_EN (0x1 << 0x3)
+
+/* DDR RAM defines */
+#define DDR_CLK_MHZ 303 /* DDR_DPLL_MULT value */
+
+static void rtc32k_enable(void)
+{
+ struct rtc_regs *rtc = (struct rtc_regs *)AM335X_RTC_BASE;
+
+ /*
+ * Unlock the RTC's registers. For more details please see the
+ * RTC_SS section of the TRM. In order to unlock we need to
+ * write these specific values (keys) in this order.
+ */
+ writel(0x83e70b13, &rtc->kick0r);
+ writel(0x95a4f1e0, &rtc->kick1r);
+
+ /* Enable the RTC 32K OSC by setting bits 3 and 6. */
+ writel((1 << 3) | (1 << 6), &rtc->osc);
+}
+
+static const struct ddr_data ddr3_data = {
+ .datardsratio0 = MT41J256M8HX15E_RD_DQS,
+ .datawdsratio0 = MT41J256M8HX15E_WR_DQS,
+ .datafwsratio0 = MT41J256M8HX15E_PHY_FIFO_WE,
+ .datawrsratio0 = MT41J256M8HX15E_PHY_WR_DATA,
+ .datadldiff0 = PHY_DLL_LOCK_DIFF,
+};
+
+static const struct cmd_control ddr3_cmd_ctrl_data = {
+ .cmd0csratio = MT41J256M8HX15E_RATIO,
+ .cmd0dldiff = MT41J256M8HX15E_DLL_LOCK_DIFF,
+ .cmd0iclkout = MT41J256M8HX15E_INVERT_CLKOUT,
+
+ .cmd1csratio = MT41J256M8HX15E_RATIO,
+ .cmd1dldiff = MT41J256M8HX15E_DLL_LOCK_DIFF,
+ .cmd1iclkout = MT41J256M8HX15E_INVERT_CLKOUT,
+
+ .cmd2csratio = MT41J256M8HX15E_RATIO,
+ .cmd2dldiff = MT41J256M8HX15E_DLL_LOCK_DIFF,
+ .cmd2iclkout = MT41J256M8HX15E_INVERT_CLKOUT,
+};
+
+static struct emif_regs ddr3_emif_reg_data = {
+ .sdram_config = MT41J256M8HX15E_EMIF_SDCFG,
+ .ref_ctrl = MT41J256M8HX15E_EMIF_SDREF,
+ .sdram_tim1 = MT41J256M8HX15E_EMIF_TIM1,
+ .sdram_tim2 = MT41J256M8HX15E_EMIF_TIM2,
+ .sdram_tim3 = MT41J256M8HX15E_EMIF_TIM3,
+ .zq_config = MT41J256M8HX15E_ZQ_CFG,
+ .emif_ddr_phy_ctlr_1 = MT41J256M8HX15E_EMIF_READ_LATENCY,
+};
+#endif
+
+/*
+ * early system init of muxing and clocks.
+ */
+void s_init(void)
+{
+ /*
+ * WDT1 is already running when the bootloader gets control
+ * Disable it to avoid "random" resets
+ */
+ writel(0xAAAA, &wdtimer->wdtwspr);
+ while (readl(&wdtimer->wdtwwps) != 0x0)
+ ;
+ writel(0x5555, &wdtimer->wdtwspr);
+ while (readl(&wdtimer->wdtwwps) != 0x0)
+ ;
+
+#ifdef CONFIG_SPL_BUILD
+ /* Setup the PLLs and the clocks for the peripherals */
+ pll_init();
+
+ /* Enable RTC32K clock */
+ rtc32k_enable();
+
+ /* UART softreset */
+ u32 regval;
+
+ enable_uart0_pin_mux();
+
+ regval = readl(&uart_base->uartsyscfg);
+ regval |= UART_RESET;
+ writel(regval, &uart_base->uartsyscfg);
+ while ((readl(&uart_base->uartsyssts) & UART_CLK_RUNNING_MASK)
+ != UART_CLK_RUNNING_MASK)
+ ;
+
+ /* Disable smart idle */
+ regval = readl(&uart_base->uartsyscfg);
+ regval |= UART_SMART_IDLE_EN;
+ writel(regval, &uart_base->uartsyscfg);
+
+ gd = &gdata;
+
+ preloader_console_init();
+
+ /* Initalize the board header */
+ enable_i2c0_pin_mux();
+ i2c_init(CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE);
+
+ enable_board_pin_mux();
+
+ config_ddr(DDR_CLK_MHZ, MT41J256M8HX15E_IOCTRL_VALUE, &ddr3_data,
+ &ddr3_cmd_ctrl_data, &ddr3_emif_reg_data);
+#endif
+}
+
+/*
+ * Basic board specific setup. Pinmux has been handled already.
+ */
+int board_init(void)
+{
+ i2c_init(CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE);
+
+ gd->bd->bi_boot_params = PHYS_DRAM_1 + 0x100;
+
+ return 0;
+}
+
+#ifdef CONFIG_DRIVER_TI_CPSW
+static void cpsw_control(int enabled)
+{
+ /* VTP can be added here */
+
+ return;
+}
+
+static struct cpsw_slave_data cpsw_slaves[] = {
+ {
+ .slave_reg_ofs = 0x208,
+ .sliver_reg_ofs = 0xd80,
+ .phy_id = 0,
+ .phy_if = PHY_INTERFACE_MODE_RGMII,
+ },
+ {
+ .slave_reg_ofs = 0x308,
+ .sliver_reg_ofs = 0xdc0,
+ .phy_id = 1,
+ .phy_if = PHY_INTERFACE_MODE_RGMII,
+ },
+};
+
+static struct cpsw_platform_data cpsw_data = {
+ .mdio_base = AM335X_CPSW_MDIO_BASE,
+ .cpsw_base = AM335X_CPSW_BASE,
+ .mdio_div = 0xff,
+ .channels = 8,
+ .cpdma_reg_ofs = 0x800,
+ .slaves = 1,
+ .slave_data = cpsw_slaves,
+ .ale_reg_ofs = 0xd00,
+ .ale_entries = 1024,
+ .host_port_reg_ofs = 0x108,
+ .hw_stats_reg_ofs = 0x900,
+ .mac_control = (1 << 5),
+ .control = cpsw_control,
+ .host_port_num = 0,
+ .version = CPSW_CTRL_VERSION_2,
+};
+#endif
+
+#if defined(CONFIG_DRIVER_TI_CPSW) || \
+ (defined(CONFIG_USB_ETHER) && defined(CONFIG_MUSB_GADGET))
+int board_eth_init(bd_t *bis)
+{
+ int rv, n = 0;
+#ifdef CONFIG_DRIVER_TI_CPSW
+ uint8_t mac_addr[6];
+ uint32_t mac_hi, mac_lo;
+
+ if (!eth_getenv_enetaddr("ethaddr", mac_addr)) {
+ printf("<ethaddr> not set. Reading from E-fuse\n");
+ /* try reading mac address from efuse */
+ mac_lo = readl(&cdev->macid0l);
+ mac_hi = readl(&cdev->macid0h);
+ mac_addr[0] = mac_hi & 0xFF;
+ mac_addr[1] = (mac_hi & 0xFF00) >> 8;
+ mac_addr[2] = (mac_hi & 0xFF0000) >> 16;
+ mac_addr[3] = (mac_hi & 0xFF000000) >> 24;
+ mac_addr[4] = mac_lo & 0xFF;
+ mac_addr[5] = (mac_lo & 0xFF00) >> 8;
+
+ if (is_valid_ether_addr(mac_addr))
+ eth_setenv_enetaddr("ethaddr", mac_addr);
+ else
+ goto try_usbether;
+ }
+
+ writel(RMII_RGMII2_MODE_ENABLE, &cdev->miisel);
+
+ rv = cpsw_register(&cpsw_data);
+ if (rv < 0)
+ printf("Error %d registering CPSW switch\n", rv);
+ else
+ n += rv;
+try_usbether:
+#endif
+
+#if defined(CONFIG_USB_ETHER) && !defined(CONFIG_SPL_BUILD)
+ rv = usb_eth_initialize(bis);
+ if (rv < 0)
+ printf("Error %d registering USB_ETHER\n", rv);
+ else
+ n += rv;
+#endif
+ return n;
+}
+#endif
diff --git a/board/phytec/pcm051/board.h b/board/phytec/pcm051/board.h
new file mode 100644
index 0000000..c2630d7
--- /dev/null
+++ b/board/phytec/pcm051/board.h
@@ -0,0 +1,33 @@
+/*
+ * board.h
+ *
+ * Phytec phyCORE-AM335x (pcm051) boards information header
+ *
+ * Copyright (C) 2013, Lemonage Software GmbH
+ * Author Lars Poeschel <poeschel@lemonage.de>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR /PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#ifndef _BOARD_H_
+#define _BOARD_H_
+
+/*
+ * We have three pin mux functions that must exist. We must be able to enable
+ * uart0, for initial output and i2c0 to read the main EEPROM. We then have a
+ * main pinmux function that can be overridden to enable all other pinmux that
+ * is required on the board.
+ */
+void enable_uart0_pin_mux(void);
+void enable_i2c0_pin_mux(void);
+void enable_board_pin_mux(void);
+void enable_cbmux_pin_mux(void);
+#endif
diff --git a/board/phytec/pcm051/mux.c b/board/phytec/pcm051/mux.c
new file mode 100644
index 0000000..2cda331
--- /dev/null
+++ b/board/phytec/pcm051/mux.c
@@ -0,0 +1,133 @@
+/*
+ * mux.c
+ *
+ * Copyright (C) 2013 Lemonage Software GmbH
+ * Author Lars Poeschel <poeschel@lemonage.de>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation version 2.
+ *
+ * This program is distributed "as is" WITHOUT ANY WARRANTY of any
+ * kind, whether express or implied; without even the implied warranty
+ * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#include <common.h>
+#include <asm/arch/sys_proto.h>
+#include <asm/arch/hardware.h>
+#include <asm/arch/mux.h>
+#include <asm/io.h>
+#include "board.h"
+
+static struct module_pin_mux uart0_pin_mux[] = {
+ {OFFSET(uart0_rxd), (MODE(0) | PULLUP_EN | RXACTIVE)}, /* UART0_RXD */
+ {OFFSET(uart0_txd), (MODE(0) | PULLUDEN)}, /* UART0_TXD */
+ {-1},
+};
+
+#ifdef CONFIG_MMC
+static struct module_pin_mux mmc0_pin_mux[] = {
+ {OFFSET(mmc0_dat3), (MODE(0) | RXACTIVE | PULLUP_EN)}, /* MMC0_DAT3 */
+ {OFFSET(mmc0_dat2), (MODE(0) | RXACTIVE | PULLUP_EN)}, /* MMC0_DAT2 */
+ {OFFSET(mmc0_dat1), (MODE(0) | RXACTIVE | PULLUP_EN)}, /* MMC0_DAT1 */
+ {OFFSET(mmc0_dat0), (MODE(0) | RXACTIVE | PULLUP_EN)}, /* MMC0_DAT0 */
+ {OFFSET(mmc0_clk), (MODE(0) | RXACTIVE | PULLUP_EN)}, /* MMC0_CLK */
+ {OFFSET(mmc0_cmd), (MODE(0) | RXACTIVE | PULLUP_EN)}, /* MMC0_CMD */
+ {OFFSET(mcasp0_aclkr), (MODE(4) | RXACTIVE)}, /* MMC0_WP */
+ {OFFSET(spi0_cs1), (MODE(5) | RXACTIVE | PULLUP_EN)}, /* MMC0_CD */
+ {-1},
+};
+#endif
+
+#ifdef CONFIG_I2C
+static struct module_pin_mux i2c0_pin_mux[] = {
+ {OFFSET(i2c0_sda), (MODE(0) | RXACTIVE |
+ PULLUDEN | SLEWCTRL)}, /* I2C_DATA */
+ {OFFSET(i2c0_scl), (MODE(0) | RXACTIVE |
+ PULLUDEN | SLEWCTRL)}, /* I2C_SCLK */
+ {-1},
+};
+#endif
+
+#ifdef CONFIG_SPI
+static struct module_pin_mux spi0_pin_mux[] = {
+ {OFFSET(spi0_sclk), (MODE(0) | RXACTIVE | PULLUDEN)}, /* SPI0_SCLK */
+ {OFFSET(spi0_d0), (MODE(0) | RXACTIVE |
+ PULLUDEN | PULLUP_EN)}, /* SPI0_D0 */
+ {OFFSET(spi0_d1), (MODE(0) | RXACTIVE | PULLUDEN)}, /* SPI0_D1 */
+ {OFFSET(spi0_cs0), (MODE(0) | RXACTIVE |
+ PULLUDEN | PULLUP_EN)}, /* SPI0_CS0 */
+ {-1},
+};
+#endif
+
+static struct module_pin_mux gpio0_7_pin_mux[] = {
+ {OFFSET(ecap0_in_pwm0_out), (MODE(7) | PULLUDEN)}, /* GPIO0_7 */
+ {-1},
+};
+
+static struct module_pin_mux rmii1_pin_mux[] = {
+ {OFFSET(mii1_crs), MODE(1) | RXACTIVE}, /* RMII1_CRS */
+ {OFFSET(mii1_rxerr), MODE(1) | RXACTIVE}, /* RMII1_RXERR */
+ {OFFSET(mii1_txen), MODE(1)}, /* RMII1_TXEN */
+ {OFFSET(mii1_txd1), MODE(1)}, /* RMII1_TXD1 */
+ {OFFSET(mii1_txd0), MODE(1)}, /* RMII1_TXD0 */
+ {OFFSET(mii1_rxd1), MODE(1) | RXACTIVE}, /* RMII1_RXD1 */
+ {OFFSET(mii1_rxd0), MODE(1) | RXACTIVE}, /* RMII1_RXD0 */
+ {OFFSET(mdio_data), MODE(0) | RXACTIVE | PULLUP_EN}, /* MDIO_DATA */
+ {OFFSET(mdio_clk), MODE(0) | PULLUP_EN}, /* MDIO_CLK */
+ {OFFSET(rmii1_refclk), MODE(0) | RXACTIVE}, /* RMII1_REFCLK */
+ {-1},
+};
+
+static struct module_pin_mux cbmux_pin_mux[] = {
+ {OFFSET(uart0_ctsn), MODE(7) | RXACTIVE | PULLDOWN_EN}, /* JP3 */
+ {OFFSET(uart0_rtsn), MODE(7) | RXACTIVE | PULLUP_EN}, /* JP4 */
+ {-1},
+};
+
+#ifdef CONFIG_NAND
+static struct module_pin_mux nand_pin_mux[] = {
+ {OFFSET(gpmc_ad0), (MODE(0) | PULLUP_EN | RXACTIVE)}, /* NAND AD0 */
+ {OFFSET(gpmc_ad1), (MODE(0) | PULLUP_EN | RXACTIVE)}, /* NAND AD1 */
+ {OFFSET(gpmc_ad2), (MODE(0) | PULLUP_EN | RXACTIVE)}, /* NAND AD2 */
+ {OFFSET(gpmc_ad3), (MODE(0) | PULLUP_EN | RXACTIVE)}, /* NAND AD3 */
+ {OFFSET(gpmc_ad4), (MODE(0) | PULLUP_EN | RXACTIVE)}, /* NAND AD4 */
+ {OFFSET(gpmc_ad5), (MODE(0) | PULLUP_EN | RXACTIVE)}, /* NAND AD5 */
+ {OFFSET(gpmc_ad6), (MODE(0) | PULLUP_EN | RXACTIVE)}, /* NAND AD6 */
+ {OFFSET(gpmc_ad7), (MODE(0) | PULLUP_EN | RXACTIVE)}, /* NAND AD7 */
+ {OFFSET(gpmc_wait0), (MODE(0) | RXACTIVE | PULLUP_EN)}, /* NAND WAIT */
+ {OFFSET(gpmc_wpn), (MODE(7) | PULLUP_EN | RXACTIVE)}, /* NAND_WPN */
+ {OFFSET(gpmc_csn0), (MODE(0) | PULLUDEN)}, /* NAND_CS0 */
+ {OFFSET(gpmc_advn_ale), (MODE(0) | PULLUDEN)}, /* NAND_ADV_ALE */
+ {OFFSET(gpmc_oen_ren), (MODE(0) | PULLUDEN)}, /* NAND_OE */
+ {OFFSET(gpmc_wen), (MODE(0) | PULLUDEN)}, /* NAND_WEN */
+ {OFFSET(gpmc_be0n_cle), (MODE(0) | PULLUDEN)}, /* NAND_BE_CLE */
+ {-1},
+};
+#endif
+
+void enable_uart0_pin_mux(void)
+{
+ configure_module_pin_mux(uart0_pin_mux);
+}
+
+void enable_i2c0_pin_mux(void)
+{
+ configure_module_pin_mux(i2c0_pin_mux);
+}
+
+void enable_board_pin_mux()
+{
+ configure_module_pin_mux(rmii1_pin_mux);
+ configure_module_pin_mux(mmc0_pin_mux);
+ configure_module_pin_mux(cbmux_pin_mux);
+#ifdef CONFIG_NAND
+ configure_module_pin_mux(nand_pin_mux);
+#endif
+#ifdef CONFIG_SPI
+ configure_module_pin_mux(spi0_pin_mux);
+#endif
+}