[Strange. I _did_ check these in before. Seems SF restored an old
version of the repository???]
* Patch by Reinhard Meyer, 09 Jan 2004:
- add RTC support for MPC5200 based boards (requires RTC_XTAL)
* Add support for IDE LED on BMS2003 board
(exclusive with status LED!)
* Add support for PS/2 keyboard (used with PS/2 multiplexor on
BMS2003 board)
* Patches by Reinhard Meyer, 4 Jan 2004 + 7 Jan 2004:
Add common files for "emk" boards
diff --git a/drivers/pc_keyb.c b/drivers/pc_keyb.c
new file mode 100644
index 0000000..07c7914
--- /dev/null
+++ b/drivers/pc_keyb.c
@@ -0,0 +1,256 @@
+/***********************************************************************
+ *
+ * (C) Copyright 2004
+ * DENX Software Engineering
+ * Wolfgang Denk, wd@denx.de
+ * All rights reserved.
+ *
+ * PS/2 keyboard driver
+ *
+ * Originally from linux source (drivers/char/pc_keyb.c)
+ *
+ ***********************************************************************/
+
+#include <common.h>
+
+#ifdef CONFIG_PS2KBD
+
+#include <keyboard.h>
+#include <pc_keyb.h>
+
+#undef KBG_DEBUG
+
+#ifdef KBG_DEBUG
+#define PRINTF(fmt,args...) printf (fmt ,##args)
+#else
+#define PRINTF(fmt,args...)
+#endif
+
+
+/*
+ * This reads the keyboard status port, and does the
+ * appropriate action.
+ *
+ */
+static unsigned char handle_kbd_event(void)
+{
+ unsigned char status = kbd_read_status();
+ unsigned int work = 10000;
+
+ while ((--work > 0) && (status & KBD_STAT_OBF)) {
+ unsigned char scancode;
+
+ scancode = kbd_read_input();
+
+ /* Error bytes must be ignored to make the
+ Synaptics touchpads compaq use work */
+ /* Ignore error bytes */
+ if (!(status & (KBD_STAT_GTO | KBD_STAT_PERR))) {
+ if (status & KBD_STAT_MOUSE_OBF)
+ ; /* not supported: handle_mouse_event(scancode); */
+ else
+ handle_scancode(scancode);
+ }
+ status = kbd_read_status();
+ }
+ if (!work)
+ PRINTF("pc_keyb: controller jammed (0x%02X).\n", status);
+ return status;
+}
+
+
+static int kbd_read_data(void)
+{
+ int val;
+ unsigned char status;
+
+ val=-1;
+ status = kbd_read_status();
+ if (status & KBD_STAT_OBF) {
+ val = kbd_read_input();
+ if (status & (KBD_STAT_GTO | KBD_STAT_PERR))
+ val = -2;
+ }
+ return val;
+}
+
+static int kbd_wait_for_input(void)
+{
+ unsigned long timeout;
+ int val;
+
+ timeout = KBD_TIMEOUT;
+ val=kbd_read_data();
+ while(val < 0) {
+ if(timeout--==0)
+ return -1;
+ udelay(1000);
+ val=kbd_read_data();
+ }
+ return val;
+}
+
+
+static int kb_wait(void)
+{
+ unsigned long timeout = KBC_TIMEOUT * 10;
+
+ do {
+ unsigned char status = handle_kbd_event();
+ if (!(status & KBD_STAT_IBF))
+ return 0; /* ok */
+ udelay(1000);
+ timeout--;
+ } while (timeout);
+ return 1;
+}
+
+static void kbd_write_command_w(int data)
+{
+ if(kb_wait())
+ PRINTF("timeout in kbd_write_command_w\n");
+ kbd_write_command(data);
+}
+
+static void kbd_write_output_w(int data)
+{
+ if(kb_wait())
+ PRINTF("timeout in kbd_write_output_w\n");
+ kbd_write_output(data);
+}
+
+static void kbd_send_data(unsigned char data)
+{
+ kbd_write_output_w(data);
+ kbd_wait_for_input();
+}
+
+
+static char * kbd_initialize(void)
+{
+ int status;
+
+ /*
+ * Test the keyboard interface.
+ * This seems to be the only way to get it going.
+ * If the test is successful a x55 is placed in the input buffer.
+ */
+ kbd_write_command_w(KBD_CCMD_SELF_TEST);
+ if (kbd_wait_for_input() != 0x55)
+ return "Kbd: failed self test";
+ /*
+ * Perform a keyboard interface test. This causes the controller
+ * to test the keyboard clock and data lines. The results of the
+ * test are placed in the input buffer.
+ */
+ kbd_write_command_w(KBD_CCMD_KBD_TEST);
+ if (kbd_wait_for_input() != 0x00)
+ return "Kbd: interface failed self test";
+ /*
+ * Enable the keyboard by allowing the keyboard clock to run.
+ */
+ kbd_write_command_w(KBD_CCMD_KBD_ENABLE);
+
+ /*
+ * Reset keyboard. If the read times out
+ * then the assumption is that no keyboard is
+ * plugged into the machine.
+ * This defaults the keyboard to scan-code set 2.
+ *
+ * Set up to try again if the keyboard asks for RESEND.
+ */
+ do {
+ kbd_write_output_w(KBD_CMD_RESET);
+ status = kbd_wait_for_input();
+ if (status == KBD_REPLY_ACK)
+ break;
+ if (status != KBD_REPLY_RESEND) {
+ PRINTF("status: %X\n",status);
+ return "Kbd: reset failed, no ACK";
+ }
+ } while (1);
+ if (kbd_wait_for_input() != KBD_REPLY_POR)
+ return "Kbd: reset failed, no POR";
+
+ /*
+ * Set keyboard controller mode. During this, the keyboard should be
+ * in the disabled state.
+ *
+ * Set up to try again if the keyboard asks for RESEND.
+ */
+ do {
+ kbd_write_output_w(KBD_CMD_DISABLE);
+ status = kbd_wait_for_input();
+ if (status == KBD_REPLY_ACK)
+ break;
+ if (status != KBD_REPLY_RESEND)
+ return "Kbd: disable keyboard: no ACK";
+ } while (1);
+
+ kbd_write_command_w(KBD_CCMD_WRITE_MODE);
+ kbd_write_output_w(KBD_MODE_KBD_INT
+ | KBD_MODE_SYS
+ | KBD_MODE_DISABLE_MOUSE
+ | KBD_MODE_KCC);
+
+ /* ibm powerpc portables need this to use scan-code set 1 -- Cort */
+ kbd_write_command_w(KBD_CCMD_READ_MODE);
+ if (!(kbd_wait_for_input() & KBD_MODE_KCC)) {
+ /*
+ * If the controller does not support conversion,
+ * Set the keyboard to scan-code set 1.
+ */
+ kbd_write_output_w(0xF0);
+ kbd_wait_for_input();
+ kbd_write_output_w(0x01);
+ kbd_wait_for_input();
+ }
+ kbd_write_output_w(KBD_CMD_ENABLE);
+ if (kbd_wait_for_input() != KBD_REPLY_ACK)
+ return "Kbd: enable keyboard: no ACK";
+
+ /*
+ * Finally, set the typematic rate to maximum.
+ */
+ kbd_write_output_w(KBD_CMD_SET_RATE);
+ if (kbd_wait_for_input() != KBD_REPLY_ACK)
+ return "Kbd: Set rate: no ACK";
+ kbd_write_output_w(0x00);
+ if (kbd_wait_for_input() != KBD_REPLY_ACK)
+ return "Kbd: Set rate: no ACK";
+ return NULL;
+}
+
+static void kbd_interrupt(void *dev_id)
+{
+ handle_kbd_event();
+}
+
+/******************************************************************
+ * Init
+ ******************************************************************/
+
+int kbd_init_hw(void)
+{
+ char* result;
+
+ kbd_request_region();
+
+ result=kbd_initialize();
+ if (result==NULL) {
+ PRINTF("AT Keyboard initialized\n");
+ kbd_request_irq(kbd_interrupt);
+ return (1);
+ } else {
+ printf("%s\n",result);
+ return (-1);
+ }
+}
+
+void pckbd_leds(unsigned char leds)
+{
+ kbd_send_data(KBD_CMD_SET_LEDS);
+ kbd_send_data(leds);
+}
+
+#endif /* CONFIG_PS2KBD */