drivers: usb: musb: adopt musb backend driver to driver model
Currently all backend driver ops uses hard coded physical
address, so to adopt the driver to DM, add device pointer to ops
call backs so that drivers can get physical addresses from the
usb driver priv/plat data.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
diff --git a/drivers/usb/musb-new/am35x.c b/drivers/usb/musb-new/am35x.c
index b8791dd..0167ea7 100644
--- a/drivers/usb/musb-new/am35x.c
+++ b/drivers/usb/musb-new/am35x.c
@@ -336,7 +336,7 @@
if (ret == IRQ_HANDLED || epintr || usbintr) {
/* clear level interrupt */
if (data->clear_irq)
- data->clear_irq();
+ data->clear_irq(data->dev);
/* write EOI */
musb_writel(reg_base, USB_END_OF_INTR_REG, 0);
}
@@ -401,14 +401,14 @@
/* Reset the musb */
if (data->reset)
- data->reset();
+ data->reset(data->dev);
/* Reset the controller */
musb_writel(reg_base, USB_CTRL_REG, AM35X_SOFT_RESET_MASK);
/* Start the on-chip PHY and its PLL. */
if (data->set_phy_power)
- data->set_phy_power(1);
+ data->set_phy_power(data->dev, 1);
msleep(5);
@@ -416,7 +416,7 @@
/* clear level interrupt */
if (data->clear_irq)
- data->clear_irq();
+ data->clear_irq(data->dev);
return 0;
}
@@ -439,7 +439,7 @@
/* Shutdown the on-chip PHY and its PLL. */
if (data->set_phy_power)
- data->set_phy_power(0);
+ data->set_phy_power(data->dev, 0);
#ifndef __UBOOT__
usb_put_phy(musb->xceiv);
@@ -630,7 +630,7 @@
/* Shutdown the on-chip PHY and its PLL. */
if (data->set_phy_power)
- data->set_phy_power(0);
+ data->set_phy_power(data->dev, 0);
clk_disable(glue->phy_clk);
clk_disable(glue->clk);
@@ -647,7 +647,7 @@
/* Start the on-chip PHY and its PLL. */
if (data->set_phy_power)
- data->set_phy_power(1);
+ data->set_phy_power(data->dev, 1);
ret = clk_enable(glue->phy_clk);
if (ret) {
diff --git a/drivers/usb/musb-new/musb_dsps.c b/drivers/usb/musb-new/musb_dsps.c
index a71db76..399b85b 100644
--- a/drivers/usb/musb-new/musb_dsps.c
+++ b/drivers/usb/musb-new/musb_dsps.c
@@ -452,7 +452,7 @@
/* Start the on-chip PHY and its PLL. */
if (data->set_phy_power)
- data->set_phy_power(1);
+ data->set_phy_power(data->dev, 1);
musb->isr = dsps_interrupt;
@@ -493,7 +493,7 @@
/* Shutdown the on-chip PHY and its PLL. */
if (data->set_phy_power)
- data->set_phy_power(0);
+ data->set_phy_power(data->dev, 0);
#ifndef __UBOOT__
/* NOP driver needs change if supporting dual instance */
@@ -693,7 +693,7 @@
/* Shutdown the on-chip PHY and its PLL. */
if (data->set_phy_power)
- data->set_phy_power(0);
+ data->set_phy_power(data->dev, 0);
return 0;
}
@@ -705,7 +705,7 @@
/* Start the on-chip PHY and its PLL. */
if (data->set_phy_power)
- data->set_phy_power(1);
+ data->set_phy_power(data->dev, 1);
return 0;
}