arm: mvebu: Add CRS305-1G-4S board
CRS305-1G-4S has a switch chip with an integrated CPU (98DX3236) and
like some of the other similar boards requires bin_hdr.
bin_hdr (DDR3 init stage) is currently retrieved from the stock
bootloader and compiled into the kwb image.
Adds support for U-Boot, enable UART, SPI, Winbond SPI flash chip
support and writing env to SPI flash.
Signed-off-by: Luka Kovacic <me@lukakovacic.xyz>
Reviewed-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
index 8b97143..56bf5aa 100644
--- a/arch/arm/dts/Makefile
+++ b/arch/arm/dts/Makefile
@@ -162,7 +162,8 @@
armada-38x-controlcenterdc.dtb \
armada-385-atl-x530.dtb \
armada-385-atl-x530DP.dtb \
- armada-xp-db-xc3-24g4xg.dtb
+ armada-xp-db-xc3-24g4xg.dtb \
+ armada-xp-crs305-1g-4s.dtb
dtb-$(CONFIG_ARCH_UNIPHIER_LD11) += \
uniphier-ld11-global.dtb \
diff --git a/arch/arm/dts/armada-xp-crs305-1g-4s-u-boot.dtsi b/arch/arm/dts/armada-xp-crs305-1g-4s-u-boot.dtsi
new file mode 100644
index 0000000..8576a02
--- /dev/null
+++ b/arch/arm/dts/armada-xp-crs305-1g-4s-u-boot.dtsi
@@ -0,0 +1,13 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+
+&uart0 {
+ u-boot,dm-pre-reloc;
+};
+
+&spi0 {
+ u-boot,dm-pre-reloc;
+
+ spi-flash@0 {
+ u-boot,dm-pre-reloc;
+ };
+};
diff --git a/arch/arm/dts/armada-xp-crs305-1g-4s.dts b/arch/arm/dts/armada-xp-crs305-1g-4s.dts
new file mode 100644
index 0000000..1116f5c
--- /dev/null
+++ b/arch/arm/dts/armada-xp-crs305-1g-4s.dts
@@ -0,0 +1,110 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Device Tree file for CRS305-1G-4S board
+ *
+ * Copyright (C) 2016 Allied Telesis Labs
+ *
+ * Based on armada-xp-db.dts
+ *
+ * Note: this Device Tree assumes that the bootloader has remapped the
+ * internal registers to 0xf1000000 (instead of the default
+ * 0xd0000000). The 0xf1000000 is the default used by the recent,
+ * DT-capable, U-Boot bootloaders provided by Marvell. Some earlier
+ * boards were delivered with an older version of the bootloader that
+ * left internal registers mapped at 0xd0000000. If you are in this
+ * situation, you should either update your bootloader (preferred
+ * solution) or the below Device Tree should be adjusted.
+ */
+
+/dts-v1/;
+#include "armada-xp-98dx3236.dtsi"
+#include "armada-xp-crs305-1g-4s-u-boot.dtsi"
+
+/ {
+ model = "CRS305-1G-4S";
+ compatible = "marvell,armadaxp-98dx3236", "marvell,armadaxp-mv78260", "marvell,armadaxp", "marvell,armada-370-xp";
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ bootargs = "console=ttyS0,115200 earlyprintk";
+ };
+
+ aliases {
+ spi0 = &spi0;
+ };
+
+ memory {
+ device_type = "memory";
+ reg = <0 0x00000000 0 0x20000000>; /* 512 MB */
+ };
+};
+
+&L2 {
+ arm,parity-enable;
+ marvell,ecc-enable;
+};
+
+&devbus_bootcs {
+ status = "okay";
+
+ /* Device Bus parameters are required */
+
+ /* Read parameters */
+ devbus,bus-width = <16>;
+ devbus,turn-off-ps = <60000>;
+ devbus,badr-skew-ps = <0>;
+ devbus,acc-first-ps = <124000>;
+ devbus,acc-next-ps = <248000>;
+ devbus,rd-setup-ps = <0>;
+ devbus,rd-hold-ps = <0>;
+
+ /* Write parameters */
+ devbus,sync-enable = <0>;
+ devbus,wr-high-ps = <60000>;
+ devbus,wr-low-ps = <60000>;
+ devbus,ale-wr-ps = <60000>;
+};
+
+&uart0 {
+ status = "okay";
+};
+
+&uart1 {
+ status = "okay";
+};
+
+&i2c0 {
+ clock-frequency = <100000>;
+ status = "okay";
+};
+
+&usb0 {
+ status = "okay";
+};
+
+&spi0 {
+ status = "okay";
+
+ spi-flash@0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "spi-flash", "jedec,spi-nor";
+ reg = <0>; /* Chip select 0 */
+ spi-max-frequency = <108000000>;
+ m25p,fast-read;
+
+ partition@u-boot {
+ reg = <0x00000000 0x00100000>;
+ label = "u-boot";
+ };
+ partition@u-boot-env {
+ reg = <0x00100000 0x00040000>;
+ label = "u-boot-env";
+ };
+ partition@unused {
+ reg = <0x00140000 0x00ec0000>;
+ label = "unused";
+ };
+
+ };
+};