ARM: dts: stm32: Synchronize DT with kernel one
This patch synchronizes U-boot DT with kernel one
This is based on https://patchwork.kernel.org/cover/10797115/
This patch adds initial support of STM32MP157 discovery boards:
- Add support of stm32mp157a discovery1 board (part number: STM32MP157A-DK1).
This board embeds a STM32MP157a SOC with AC package (TFBGA361, 148 ios)
and 512MB of DDR3. Several connections are available on this boards:
4*USB2.0, 1*USB2.0 typeC, SDcard, RJ45, HDMI, Arduino connector, ...
- Add support of stm32mp157c discovery2 board (part number: STM32MP157C-DK2).
This board is a "super-set" of stm32mp157a-dk1. A display panel (otm8009a)
and Murata wifi/BT combo is added.
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
diff --git a/arch/arm/dts/stm32mp157a-dk1.dts b/arch/arm/dts/stm32mp157a-dk1.dts
new file mode 100644
index 0000000..0882765
--- /dev/null
+++ b/arch/arm/dts/stm32mp157a-dk1.dts
@@ -0,0 +1,262 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
+/*
+ * Copyright (C) STMicroelectronics 2019 - All Rights Reserved
+ * Author: Alexandre Torgue <alexandre.torgue@st.com> for STMicroelectronics.
+ */
+
+/dts-v1/;
+
+#include "stm32mp157c.dtsi"
+#include "stm32mp157-pinctrl.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/mfd/st,stpmic1.h>
+
+/ {
+ model = "STMicroelectronics STM32MP157A-DK1 Discovery Board";
+ compatible = "st,stm32mp157a-dk1", "st,stm32mp157";
+
+ aliases {
+ ethernet0 = ðernet0;
+ serial0 = &uart4;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ memory@c0000000 {
+ reg = <0xc0000000 0x20000000>;
+ };
+
+ led {
+ compatible = "gpio-leds";
+ blue {
+ label = "heartbeat";
+ gpios = <&gpiod 11 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "heartbeat";
+ default-state = "off";
+ };
+ };
+};
+
+ðernet0 {
+ status = "okay";
+ pinctrl-0 = <ðernet0_rgmii_pins_a>;
+ pinctrl-1 = <ðernet0_rgmii_pins_sleep_a>;
+ pinctrl-names = "default", "sleep";
+ phy-mode = "rgmii";
+ max-speed = <1000>;
+ phy-handle = <&phy0>;
+
+ mdio0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "snps,dwmac-mdio";
+ phy0: ethernet-phy@0 {
+ reg = <0>;
+ };
+ };
+};
+
+&i2c4 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c4_pins_a>;
+ i2c-scl-rising-time-ns = <185>;
+ i2c-scl-falling-time-ns = <20>;
+ status = "okay";
+ /delete-property/dmas;
+ /delete-property/dma-names;
+
+ pmic: stpmic@33 {
+ compatible = "st,stpmic1";
+ reg = <0x33>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ status = "okay";
+
+ st,main-control-register = <0x04>;
+ st,vin-control-register = <0xc0>;
+ st,usb-control-register = <0x20>;
+
+ regulators {
+ compatible = "st,stpmic1-regulators";
+
+ ldo1-supply = <&v3v3>;
+ ldo3-supply = <&vdd_ddr>;
+ ldo6-supply = <&v3v3>;
+ pwr_sw1-supply = <&bst_out>;
+ pwr_sw2-supply = <&bst_out>;
+
+ vddcore: buck1 {
+ regulator-name = "vddcore";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1350000>;
+ regulator-always-on;
+ regulator-initial-mode = <0>;
+ regulator-over-current-protection;
+ };
+
+ vdd_ddr: buck2 {
+ regulator-name = "vdd_ddr";
+ regulator-min-microvolt = <1350000>;
+ regulator-max-microvolt = <1350000>;
+ regulator-always-on;
+ regulator-initial-mode = <0>;
+ regulator-over-current-protection;
+ };
+
+ vdd: buck3 {
+ regulator-name = "vdd";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ st,mask-reset;
+ regulator-initial-mode = <0>;
+ regulator-over-current-protection;
+ };
+
+ v3v3: buck4 {
+ regulator-name = "v3v3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ regulator-over-current-protection;
+ regulator-initial-mode = <0>;
+ };
+
+ v1v8_audio: ldo1 {
+ regulator-name = "v1v8_audio";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ interrupts = <IT_CURLIM_LDO1 0>;
+ };
+
+ v3v3_hdmi: ldo2 {
+ regulator-name = "v3v3_hdmi";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ interrupts = <IT_CURLIM_LDO2 0>;
+ };
+
+ vtt_ddr: ldo3 {
+ regulator-name = "vtt_ddr";
+ regulator-min-microvolt = <500000>;
+ regulator-max-microvolt = <750000>;
+ regulator-always-on;
+ regulator-over-current-protection;
+ };
+
+ vdd_usb: ldo4 {
+ regulator-name = "vdd_usb";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ interrupts = <IT_CURLIM_LDO4 0>;
+ };
+
+ vdda: ldo5 {
+ regulator-name = "vdda";
+ regulator-min-microvolt = <2900000>;
+ regulator-max-microvolt = <2900000>;
+ interrupts = <IT_CURLIM_LDO5 0>;
+ regulator-boot-on;
+ };
+
+ v1v2_hdmi: ldo6 {
+ regulator-name = "v1v2_hdmi";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-always-on;
+ interrupts = <IT_CURLIM_LDO6 0>;
+
+ };
+
+ vref_ddr: vref_ddr {
+ regulator-name = "vref_ddr";
+ regulator-always-on;
+ regulator-over-current-protection;
+ };
+
+ bst_out: boost {
+ regulator-name = "bst_out";
+ interrupts = <IT_OCP_BOOST 0>;
+ };
+
+ vbus_otg: pwr_sw1 {
+ regulator-name = "vbus_otg";
+ interrupts = <IT_OCP_OTG 0>;
+ regulator-active-discharge;
+ };
+
+ vbus_sw: pwr_sw2 {
+ regulator-name = "vbus_sw";
+ interrupts = <IT_OCP_SWOUT 0>;
+ regulator-active-discharge;
+ };
+ };
+
+ onkey {
+ compatible = "st,stpmic1-onkey";
+ interrupts = <IT_PONKEY_F 0>, <IT_PONKEY_R 1>;
+ interrupt-names = "onkey-falling", "onkey-rising";
+ status = "okay";
+ };
+
+ watchdog {
+ compatible = "st,stpmic1-wdt";
+ status = "disabled";
+ };
+ };
+};
+
+&iwdg2 {
+ timeout-sec = <32>;
+ status = "okay";
+};
+
+&pwr {
+ pwr-supply = <&vdd>;
+};
+
+&rng1 {
+ status = "okay";
+};
+
+&rtc {
+ status = "okay";
+};
+
+&sdmmc1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&sdmmc1_b4_pins_a>;
+ broken-cd;
+ st,neg-edge;
+ bus-width = <4>;
+ vmmc-supply = <&v3v3>;
+ status = "okay";
+};
+
+&uart4 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart4_pins_a>;
+ status = "okay";
+};
+
+&usbh_ehci {
+ phys = <&usbphyc_port0>;
+ phy-names = "usb";
+ status = "okay";
+};
+
+&usbphyc {
+ vdd3v3-supply = <&vdd_usb>;
+ status = "okay";
+};
+
+&vrefbuf {
+ regulator-min-microvolt = <2500000>;
+ regulator-max-microvolt = <2500000>;
+ vdda-supply = <&vdd>;
+ status = "okay";
+};