sunxi: video: Convert panel I2C to use DM_I2C
Two displays supported by the sunxi display driver (each one used by a
single board) require initialization over I2C. Both previously used
i2c_soft; replace this with the i2c-gpio instance that already exists in
those boards' device trees (sun5i-a13-utoo-p66 and sun6i-a31-colombus).
Since the i2c-gpio nodes are not referenced by any other node in the
device trees (the device trees have no panel node), the I2C bus is
selected by its node name.
This panel initialization code was the only i2c_soft user, so the
i2c_soft GPIO setup code can be removed now as well.
Reviewed-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
diff --git a/drivers/video/anx9804.c b/drivers/video/anx9804.c
index 3037ff3..52b5988 100644
--- a/drivers/video/anx9804.c
+++ b/drivers/video/anx9804.c
@@ -21,18 +21,23 @@
* This function will init an anx9804 parallel lcd to dp bridge chip
* using the passed in parameters.
*
- * @i2c_bus: Number of the i2c bus to which the anx9804 is connected.
+ * @i2c_bus: Device of the i2c bus to which the anx9804 is connected.
* @lanes: Number of displayport lanes to use
* @data_rate: Register value for the bandwidth reg 0x06: 1.62G, 0x0a: 2.7G
* @bpp: Bits per pixel, must be 18 or 24
*/
-void anx9804_init(unsigned int i2c_bus, u8 lanes, u8 data_rate, int bpp)
+void anx9804_init(struct udevice *i2c_bus, u8 lanes, u8 data_rate, int bpp)
{
- unsigned int orig_i2c_bus = i2c_get_bus_num();
- u8 c, colordepth;
- int i;
+ struct udevice *chip0, *chip1;
+ int c, colordepth, i, ret;
- i2c_set_bus_num(i2c_bus);
+ ret = i2c_get_chip(i2c_bus, 0x38, 1, &chip0);
+ if (ret)
+ return;
+
+ ret = i2c_get_chip(i2c_bus, 0x39, 1, &chip1);
+ if (ret)
+ return;
if (bpp == 18)
colordepth = 0x00; /* 6 bit */
@@ -40,24 +45,23 @@
colordepth = 0x10; /* 8 bit */
/* Reset */
- i2c_reg_write(0x39, ANX9804_RST_CTRL_REG, 1);
+ dm_i2c_reg_write(chip1, ANX9804_RST_CTRL_REG, 1);
mdelay(100);
- i2c_reg_write(0x39, ANX9804_RST_CTRL_REG, 0);
+ dm_i2c_reg_write(chip1, ANX9804_RST_CTRL_REG, 0);
/* Write 0 to the powerdown reg (powerup everything) */
- i2c_reg_write(0x39, ANX9804_POWERD_CTRL_REG, 0);
+ dm_i2c_reg_write(chip1, ANX9804_POWERD_CTRL_REG, 0);
- c = i2c_reg_read(0x39, ANX9804_DEV_IDH_REG);
+ c = dm_i2c_reg_read(chip1, ANX9804_DEV_IDH_REG);
if (c != 0x98) {
printf("Error anx9804 chipid mismatch\n");
- i2c_set_bus_num(orig_i2c_bus);
return;
}
for (i = 0; i < 100; i++) {
- c = i2c_reg_read(0x38, ANX9804_SYS_CTRL2_REG);
- i2c_reg_write(0x38, ANX9804_SYS_CTRL2_REG, c);
- c = i2c_reg_read(0x38, ANX9804_SYS_CTRL2_REG);
+ c = dm_i2c_reg_read(chip0, ANX9804_SYS_CTRL2_REG);
+ dm_i2c_reg_write(chip0, ANX9804_SYS_CTRL2_REG, c);
+ c = dm_i2c_reg_read(chip0, ANX9804_SYS_CTRL2_REG);
if ((c & ANX9804_SYS_CTRL2_CHA_STA) == 0)
break;
@@ -66,51 +70,51 @@
if (i == 100)
printf("Error anx9804 clock is not stable\n");
- i2c_reg_write(0x39, ANX9804_VID_CTRL2_REG, colordepth);
+ dm_i2c_reg_write(chip1, ANX9804_VID_CTRL2_REG, colordepth);
/* Set a bunch of analog related register values */
- i2c_reg_write(0x38, ANX9804_PLL_CTRL_REG, 0x07);
- i2c_reg_write(0x39, ANX9804_PLL_FILTER_CTRL3, 0x19);
- i2c_reg_write(0x39, ANX9804_PLL_CTRL3, 0xd9);
- i2c_reg_write(0x39, ANX9804_RST_CTRL2_REG, ANX9804_RST_CTRL2_AC_MODE);
- i2c_reg_write(0x39, ANX9804_ANALOG_DEBUG_REG1, 0xf0);
- i2c_reg_write(0x39, ANX9804_ANALOG_DEBUG_REG3, 0x99);
- i2c_reg_write(0x39, ANX9804_PLL_FILTER_CTRL1, 0x7b);
- i2c_reg_write(0x38, ANX9804_LINK_DEBUG_REG, 0x30);
- i2c_reg_write(0x39, ANX9804_PLL_FILTER_CTRL, 0x06);
+ dm_i2c_reg_write(chip0, ANX9804_PLL_CTRL_REG, 0x07);
+ dm_i2c_reg_write(chip1, ANX9804_PLL_FILTER_CTRL3, 0x19);
+ dm_i2c_reg_write(chip1, ANX9804_PLL_CTRL3, 0xd9);
+ dm_i2c_reg_write(chip1, ANX9804_RST_CTRL2_REG, ANX9804_RST_CTRL2_AC_MODE);
+ dm_i2c_reg_write(chip1, ANX9804_ANALOG_DEBUG_REG1, 0xf0);
+ dm_i2c_reg_write(chip1, ANX9804_ANALOG_DEBUG_REG3, 0x99);
+ dm_i2c_reg_write(chip1, ANX9804_PLL_FILTER_CTRL1, 0x7b);
+ dm_i2c_reg_write(chip0, ANX9804_LINK_DEBUG_REG, 0x30);
+ dm_i2c_reg_write(chip1, ANX9804_PLL_FILTER_CTRL, 0x06);
/* Force HPD */
- i2c_reg_write(0x38, ANX9804_SYS_CTRL3_REG,
- ANX9804_SYS_CTRL3_F_HPD | ANX9804_SYS_CTRL3_HPD_CTRL);
+ dm_i2c_reg_write(chip0, ANX9804_SYS_CTRL3_REG,
+ ANX9804_SYS_CTRL3_F_HPD | ANX9804_SYS_CTRL3_HPD_CTRL);
/* Power up and configure lanes */
- i2c_reg_write(0x38, ANX9804_ANALOG_POWER_DOWN_REG, 0x00);
- i2c_reg_write(0x38, ANX9804_TRAINING_LANE0_SET_REG, 0x00);
- i2c_reg_write(0x38, ANX9804_TRAINING_LANE1_SET_REG, 0x00);
- i2c_reg_write(0x38, ANX9804_TRAINING_LANE2_SET_REG, 0x00);
- i2c_reg_write(0x38, ANX9804_TRAINING_LANE3_SET_REG, 0x00);
+ dm_i2c_reg_write(chip0, ANX9804_ANALOG_POWER_DOWN_REG, 0x00);
+ dm_i2c_reg_write(chip0, ANX9804_TRAINING_LANE0_SET_REG, 0x00);
+ dm_i2c_reg_write(chip0, ANX9804_TRAINING_LANE1_SET_REG, 0x00);
+ dm_i2c_reg_write(chip0, ANX9804_TRAINING_LANE2_SET_REG, 0x00);
+ dm_i2c_reg_write(chip0, ANX9804_TRAINING_LANE3_SET_REG, 0x00);
/* Reset AUX CH */
- i2c_reg_write(0x39, ANX9804_RST_CTRL2_REG,
- ANX9804_RST_CTRL2_AC_MODE | ANX9804_RST_CTRL2_AUX);
- i2c_reg_write(0x39, ANX9804_RST_CTRL2_REG,
- ANX9804_RST_CTRL2_AC_MODE);
+ dm_i2c_reg_write(chip1, ANX9804_RST_CTRL2_REG,
+ ANX9804_RST_CTRL2_AC_MODE | ANX9804_RST_CTRL2_AUX);
+ dm_i2c_reg_write(chip1, ANX9804_RST_CTRL2_REG,
+ ANX9804_RST_CTRL2_AC_MODE);
/* Powerdown audio and some other unused bits */
- i2c_reg_write(0x39, ANX9804_POWERD_CTRL_REG, ANX9804_POWERD_AUDIO);
- i2c_reg_write(0x38, ANX9804_HDCP_CONTROL_0_REG, 0x00);
- i2c_reg_write(0x38, 0xa7, 0x00);
+ dm_i2c_reg_write(chip1, ANX9804_POWERD_CTRL_REG, ANX9804_POWERD_AUDIO);
+ dm_i2c_reg_write(chip0, ANX9804_HDCP_CONTROL_0_REG, 0x00);
+ dm_i2c_reg_write(chip0, 0xa7, 0x00);
/* Set data-rate / lanes */
- i2c_reg_write(0x38, ANX9804_LINK_BW_SET_REG, data_rate);
- i2c_reg_write(0x38, ANX9804_LANE_COUNT_SET_REG, lanes);
+ dm_i2c_reg_write(chip0, ANX9804_LINK_BW_SET_REG, data_rate);
+ dm_i2c_reg_write(chip0, ANX9804_LANE_COUNT_SET_REG, lanes);
/* Link training */
- i2c_reg_write(0x38, ANX9804_LINK_TRAINING_CTRL_REG,
- ANX9804_LINK_TRAINING_CTRL_EN);
+ dm_i2c_reg_write(chip0, ANX9804_LINK_TRAINING_CTRL_REG,
+ ANX9804_LINK_TRAINING_CTRL_EN);
mdelay(5);
for (i = 0; i < 100; i++) {
- c = i2c_reg_read(0x38, ANX9804_LINK_TRAINING_CTRL_REG);
+ c = dm_i2c_reg_read(chip0, ANX9804_LINK_TRAINING_CTRL_REG);
if ((c & 0x01) == 0)
break;
@@ -118,17 +122,14 @@
}
if(i == 100) {
printf("Error anx9804 link training timeout\n");
- i2c_set_bus_num(orig_i2c_bus);
return;
}
/* Enable */
- i2c_reg_write(0x39, ANX9804_VID_CTRL1_REG,
- ANX9804_VID_CTRL1_VID_EN | ANX9804_VID_CTRL1_EDGE);
+ dm_i2c_reg_write(chip1, ANX9804_VID_CTRL1_REG,
+ ANX9804_VID_CTRL1_VID_EN | ANX9804_VID_CTRL1_EDGE);
/* Force stream valid */
- i2c_reg_write(0x38, ANX9804_SYS_CTRL3_REG,
- ANX9804_SYS_CTRL3_F_HPD | ANX9804_SYS_CTRL3_HPD_CTRL |
- ANX9804_SYS_CTRL3_F_VALID | ANX9804_SYS_CTRL3_VALID_CTRL);
-
- i2c_set_bus_num(orig_i2c_bus);
+ dm_i2c_reg_write(chip0, ANX9804_SYS_CTRL3_REG,
+ ANX9804_SYS_CTRL3_F_HPD | ANX9804_SYS_CTRL3_HPD_CTRL |
+ ANX9804_SYS_CTRL3_F_VALID | ANX9804_SYS_CTRL3_VALID_CTRL);
}