ata: update the libata.h from ata.h of linux kernel
Current libata.h of u-boot is out of sync from linux kernel,
this patch make it be consistent with linux kernel.
Signed-off-by: Dave Liu <daveliu@freescale.com>
Signed-off-by: Tor Krill <tor@excito.com>
diff --git a/include/libata.h b/include/libata.h
index aedba74..62a1760 100644
--- a/include/libata.h
+++ b/include/libata.h
@@ -1,4 +1,6 @@
/*
+ * Copyright 2003-2004 Red Hat, Inc. All rights reserved.
+ * Copyright 2003-2004 Jeff Garzik
* Copyright (C) 2008 Freescale Semiconductor, Inc.
* Dave Liu <daveliu@freescale.com>
* port from libata of linux kernel
@@ -25,111 +27,29 @@
#include <common.h>
-/* command
- */
-enum ata_cmd {
- /* non-NCQ command */
- ATA_CMD_DEV_RESET = 0x08, /* ATAPI device reset */
- ATA_CMD_FLUSH_CACHE = 0xE7,
- ATA_CMD_FLUSH_CACHE_EXT = 0xEA,
- ATA_CMD_ID_ATA = 0xEC,
- ATA_CMD_ID_ATAPI = 0xA1,
- ATA_CMD_READ_DMA = 0xC8,
- ATA_CMD_READ_DMA_EXT = 0x25,
- ATA_CMD_WRITE_DMA = 0xCA,
- ATA_CMD_WRITE_DMA_EXT = 0x35,
- ATA_CMD_PIO_READ = 0x20,
- ATA_CMD_PIO_READ_EXT = 0x24,
- ATA_CMD_PIO_WRITE = 0x30,
- ATA_CMD_PIO_WRITE_EXT = 0x34,
- ATA_CMD_SET_FEATURES = 0xEF,
-
- /* NCQ command */
- ATA_CMD_READ_FPDMA_QUEUED = 0x60,
- ATA_CMD_WRITE_FPDMA_QUEUED = 0x61,
-};
-
-/* SETFEATURES stuff
- */
-enum ata_set_features {
- /* SETFEATURES stuff */
- SETFEATURES_XFER = 0x03,
- XFER_UDMA_7 = 0x47,
- XFER_UDMA_6 = 0x46,
- XFER_UDMA_5 = 0x45,
- XFER_UDMA_4 = 0x44,
- XFER_UDMA_3 = 0x43,
- XFER_UDMA_2 = 0x42,
- XFER_UDMA_1 = 0x41,
- XFER_UDMA_0 = 0x40,
- XFER_MW_DMA_4 = 0x24, /* CFA only */
- XFER_MW_DMA_3 = 0x23, /* CFA only */
- XFER_MW_DMA_2 = 0x22,
- XFER_MW_DMA_1 = 0x21,
- XFER_MW_DMA_0 = 0x20,
- XFER_PIO_6 = 0x0E, /* CFA only */
- XFER_PIO_5 = 0x0D, /* CFA only */
- XFER_PIO_4 = 0x0C,
- XFER_PIO_3 = 0x0B,
- XFER_PIO_2 = 0x0A,
- XFER_PIO_1 = 0x09,
- XFER_PIO_0 = 0x08,
- XFER_PIO_SLOW = 0x00,
-
- SETFEATURES_WC_ON = 0x02, /* Enable write cache */
- SETFEATURES_WC_OFF = 0x82, /* Disable write cache */
-
- SETFEATURES_SPINUP = 0x07, /* Spin-up drive */
-};
-
-enum ata_protocol {
- ATA_PROT_UNKNOWN, /* unknown */
- ATA_PROT_NODATA, /* no data */
- ATA_PROT_PIO, /* PIO data xfer */
- ATA_PROT_DMA, /* DMA */
- ATA_PROT_NCQ, /* NCQ */
- ATA_PROT_ATAPI, /* packet command, PIO data xfer */
- ATA_PROT_ATAPI_NODATA, /* packet command, no data */
- ATA_PROT_ATAPI_DMA, /* packet command, DMA */
-};
-
-enum ata_dev_typed {
- ATA_DEV_ATA, /* ATA device */
- ATA_DEV_ATAPI, /* ATAPI device */
- ATA_DEV_PMP, /* Port Multiplier Port */
- ATA_DEV_UNKNOWN, /* unknown */
-};
-
enum {
+ /* various global constants */
+ ATA_MAX_DEVICES = 2, /* per bus/port */
+ ATA_MAX_PRD = 256, /* we could make these 256/256 */
ATA_SECT_SIZE = 512,
ATA_MAX_SECTORS_128 = 128,
ATA_MAX_SECTORS = 256,
ATA_MAX_SECTORS_LBA48 = 65535,
-
- /* bits in ATA command block registers */
- ATA_HOB = (1 << 7), /* LBA48 selector */
- ATA_NIEN = (1 << 1), /* disable-irq flag */
- ATA_LBA = (1 << 6), /* LBA28 selector */
- ATA_DEV1 = (1 << 4), /* Select Device 1 (slave) */
- ATA_BUSY = (1 << 7), /* BSY status bit */
- ATA_DRDY = (1 << 6), /* device ready */
- ATA_DF = (1 << 5), /* device fault */
- ATA_DRQ = (1 << 3), /* data request i/o */
- ATA_ERR = (1 << 0), /* have an error */
- ATA_SRST = (1 << 2), /* software reset */
- ATA_ICRC = (1 << 7), /* interface CRC error */
- ATA_UNC = (1 << 6), /* uncorrectable media error */
- ATA_IDNF = (1 << 4), /* ID not found */
- ATA_ABORTED = (1 << 2), /* command aborted */
+ ATA_MAX_SECTORS_TAPE = 65535,
ATA_ID_WORDS = 256,
ATA_ID_SERNO = 10,
ATA_ID_FW_REV = 23,
ATA_ID_PROD = 27,
+ ATA_ID_OLD_PIO_MODES = 51,
ATA_ID_FIELD_VALID = 53,
ATA_ID_LBA_SECTORS = 60,
ATA_ID_MWDMA_MODES = 63,
ATA_ID_PIO_MODES = 64,
+ ATA_ID_EIDE_DMA_MIN = 65,
+ ATA_ID_EIDE_PIO = 67,
+ ATA_ID_EIDE_PIO_IORDY = 68,
+ ATA_ID_PIO4 = (1 << 1),
ATA_ID_QUEUE_DEPTH = 75,
ATA_ID_SATA_CAP = 76,
ATA_ID_SATA_FEATURES = 78,
@@ -143,8 +63,28 @@
ATA_ID_FW_REV_LEN = 8,
ATA_ID_PROD_LEN = 40,
- ATA_PIO3 = (1 << 0),
- ATA_PIO4 = ATA_PIO3 | (1 << 1),
+ ATA_PCI_CTL_OFS = 2,
+
+ ATA_PIO0 = (1 << 0),
+ ATA_PIO1 = ATA_PIO0 | (1 << 1),
+ ATA_PIO2 = ATA_PIO1 | (1 << 2),
+ ATA_PIO3 = ATA_PIO2 | (1 << 3),
+ ATA_PIO4 = ATA_PIO3 | (1 << 4),
+ ATA_PIO5 = ATA_PIO4 | (1 << 5),
+ ATA_PIO6 = ATA_PIO5 | (1 << 6),
+
+ ATA_SWDMA0 = (1 << 0),
+ ATA_SWDMA1 = ATA_SWDMA0 | (1 << 1),
+ ATA_SWDMA2 = ATA_SWDMA1 | (1 << 2),
+
+ ATA_SWDMA2_ONLY = (1 << 2),
+
+ ATA_MWDMA0 = (1 << 0),
+ ATA_MWDMA1 = ATA_MWDMA0 | (1 << 1),
+ ATA_MWDMA2 = ATA_MWDMA1 | (1 << 2),
+
+ ATA_MWDMA12_ONLY = (1 << 1) | (1 << 2),
+ ATA_MWDMA2_ONLY = (1 << 2),
ATA_UDMA0 = (1 << 0),
ATA_UDMA1 = ATA_UDMA0 | (1 << 1),
@@ -154,19 +94,357 @@
ATA_UDMA5 = ATA_UDMA4 | (1 << 5),
ATA_UDMA6 = ATA_UDMA5 | (1 << 6),
ATA_UDMA7 = ATA_UDMA6 | (1 << 7),
+ /* ATA_UDMA7 is just for completeness... doesn't exist (yet?). */
+
+ ATA_UDMA_MASK_40C = ATA_UDMA2, /* udma0-2 */
+
+ /* DMA-related */
+ ATA_PRD_SZ = 8,
+ ATA_PRD_TBL_SZ = (ATA_MAX_PRD * ATA_PRD_SZ),
+ ATA_PRD_EOT = (1 << 31), /* end-of-table flag */
+
+ ATA_DMA_TABLE_OFS = 4,
+ ATA_DMA_STATUS = 2,
+ ATA_DMA_CMD = 0,
+ ATA_DMA_WR = (1 << 3),
+ ATA_DMA_START = (1 << 0),
+ ATA_DMA_INTR = (1 << 2),
+ ATA_DMA_ERR = (1 << 1),
+ ATA_DMA_ACTIVE = (1 << 0),
+
+ /* bits in ATA command block registers */
+ ATA_HOB = (1 << 7), /* LBA48 selector */
+ ATA_NIEN = (1 << 1), /* disable-irq flag */
+ ATA_LBA = (1 << 6), /* LBA28 selector */
+ ATA_DEV1 = (1 << 4), /* Select Device 1 (slave) */
+ ATA_DEVICE_OBS = (1 << 7) | (1 << 5), /* obs bits in dev reg */
+ ATA_DEVCTL_OBS = (1 << 3), /* obsolete bit in devctl reg */
+ ATA_BUSY = (1 << 7), /* BSY status bit */
+ ATA_DRDY = (1 << 6), /* device ready */
+ ATA_DF = (1 << 5), /* device fault */
+ ATA_DRQ = (1 << 3), /* data request i/o */
+ ATA_ERR = (1 << 0), /* have an error */
+ ATA_SRST = (1 << 2), /* software reset */
+ ATA_ICRC = (1 << 7), /* interface CRC error */
+ ATA_UNC = (1 << 6), /* uncorrectable media error */
+ ATA_IDNF = (1 << 4), /* ID not found */
+ ATA_ABORTED = (1 << 2), /* command aborted */
+
+ /* ATA command block registers */
+ ATA_REG_DATA = 0x00,
+ ATA_REG_ERR = 0x01,
+ ATA_REG_NSECT = 0x02,
+ ATA_REG_LBAL = 0x03,
+ ATA_REG_LBAM = 0x04,
+ ATA_REG_LBAH = 0x05,
+ ATA_REG_DEVICE = 0x06,
+ ATA_REG_STATUS = 0x07,
+
+ ATA_REG_FEATURE = ATA_REG_ERR, /* and their aliases */
+ ATA_REG_CMD = ATA_REG_STATUS,
+ ATA_REG_BYTEL = ATA_REG_LBAM,
+ ATA_REG_BYTEH = ATA_REG_LBAH,
+ ATA_REG_DEVSEL = ATA_REG_DEVICE,
+ ATA_REG_IRQ = ATA_REG_NSECT,
+
+ /* ATA device commands */
+ ATA_CMD_DEV_RESET = 0x08, /* ATAPI device reset */
+ ATA_CMD_CHK_POWER = 0xE5, /* check power mode */
+ ATA_CMD_STANDBY = 0xE2, /* place in standby power mode */
+ ATA_CMD_IDLE = 0xE3, /* place in idle power mode */
+ ATA_CMD_EDD = 0x90, /* execute device diagnostic */
+ ATA_CMD_FLUSH = 0xE7,
+ ATA_CMD_FLUSH_EXT = 0xEA,
+ ATA_CMD_ID_ATA = 0xEC,
+ ATA_CMD_ID_ATAPI = 0xA1,
+ ATA_CMD_READ = 0xC8,
+ ATA_CMD_READ_EXT = 0x25,
+ ATA_CMD_WRITE = 0xCA,
+ ATA_CMD_WRITE_EXT = 0x35,
+ ATA_CMD_WRITE_FUA_EXT = 0x3D,
+ ATA_CMD_FPDMA_READ = 0x60,
+ ATA_CMD_FPDMA_WRITE = 0x61,
+ ATA_CMD_PIO_READ = 0x20,
+ ATA_CMD_PIO_READ_EXT = 0x24,
+ ATA_CMD_PIO_WRITE = 0x30,
+ ATA_CMD_PIO_WRITE_EXT = 0x34,
+ ATA_CMD_READ_MULTI = 0xC4,
+ ATA_CMD_READ_MULTI_EXT = 0x29,
+ ATA_CMD_WRITE_MULTI = 0xC5,
+ ATA_CMD_WRITE_MULTI_EXT = 0x39,
+ ATA_CMD_WRITE_MULTI_FUA_EXT = 0xCE,
+ ATA_CMD_SET_FEATURES = 0xEF,
+ ATA_CMD_SET_MULTI = 0xC6,
+ ATA_CMD_PACKET = 0xA0,
+ ATA_CMD_VERIFY = 0x40,
+ ATA_CMD_VERIFY_EXT = 0x42,
+ ATA_CMD_STANDBYNOW1 = 0xE0,
+ ATA_CMD_IDLEIMMEDIATE = 0xE1,
+ ATA_CMD_SLEEP = 0xE6,
+ ATA_CMD_INIT_DEV_PARAMS = 0x91,
+ ATA_CMD_READ_NATIVE_MAX = 0xF8,
+ ATA_CMD_READ_NATIVE_MAX_EXT = 0x27,
+ ATA_CMD_SET_MAX = 0xF9,
+ ATA_CMD_SET_MAX_EXT = 0x37,
+ ATA_CMD_READ_LOG_EXT = 0x2f,
+ ATA_CMD_PMP_READ = 0xE4,
+ ATA_CMD_PMP_WRITE = 0xE8,
+ ATA_CMD_CONF_OVERLAY = 0xB1,
+ ATA_CMD_SEC_FREEZE_LOCK = 0xF5,
+
+ /* READ_LOG_EXT pages */
+ ATA_LOG_SATA_NCQ = 0x10,
+
+ /* READ/WRITE LONG (obsolete) */
+ ATA_CMD_READ_LONG = 0x22,
+ ATA_CMD_READ_LONG_ONCE = 0x23,
+ ATA_CMD_WRITE_LONG = 0x32,
+ ATA_CMD_WRITE_LONG_ONCE = 0x33,
+
+ /* SETFEATURES stuff */
+ SETFEATURES_XFER = 0x03,
+ XFER_UDMA_7 = 0x47,
+ XFER_UDMA_6 = 0x46,
+ XFER_UDMA_5 = 0x45,
+ XFER_UDMA_4 = 0x44,
+ XFER_UDMA_3 = 0x43,
+ XFER_UDMA_2 = 0x42,
+ XFER_UDMA_1 = 0x41,
+ XFER_UDMA_0 = 0x40,
+ XFER_MW_DMA_4 = 0x24, /* CFA only */
+ XFER_MW_DMA_3 = 0x23, /* CFA only */
+ XFER_MW_DMA_2 = 0x22,
+ XFER_MW_DMA_1 = 0x21,
+ XFER_MW_DMA_0 = 0x20,
+ XFER_SW_DMA_2 = 0x12,
+ XFER_SW_DMA_1 = 0x11,
+ XFER_SW_DMA_0 = 0x10,
+ XFER_PIO_6 = 0x0E, /* CFA only */
+ XFER_PIO_5 = 0x0D, /* CFA only */
+ XFER_PIO_4 = 0x0C,
+ XFER_PIO_3 = 0x0B,
+ XFER_PIO_2 = 0x0A,
+ XFER_PIO_1 = 0x09,
+ XFER_PIO_0 = 0x08,
+ XFER_PIO_SLOW = 0x00,
+
+ SETFEATURES_WC_ON = 0x02, /* Enable write cache */
+ SETFEATURES_WC_OFF = 0x82, /* Disable write cache */
+
+ SETFEATURES_SPINUP = 0x07, /* Spin-up drive */
+
+ SETFEATURES_SATA_ENABLE = 0x10, /* Enable use of SATA feature */
+ SETFEATURES_SATA_DISABLE = 0x90, /* Disable use of SATA feature */
+
+ /* SETFEATURE Sector counts for SATA features */
+ SATA_AN = 0x05, /* Asynchronous Notification */
+ SATA_DIPM = 0x03, /* Device Initiated Power Management */
+
+ /* feature values for SET_MAX */
+ ATA_SET_MAX_ADDR = 0x00,
+ ATA_SET_MAX_PASSWD = 0x01,
+ ATA_SET_MAX_LOCK = 0x02,
+ ATA_SET_MAX_UNLOCK = 0x03,
+ ATA_SET_MAX_FREEZE_LOCK = 0x04,
+
+ /* feature values for DEVICE CONFIGURATION OVERLAY */
+ ATA_DCO_RESTORE = 0xC0,
+ ATA_DCO_FREEZE_LOCK = 0xC1,
+ ATA_DCO_IDENTIFY = 0xC2,
+ ATA_DCO_SET = 0xC3,
+
+ /* ATAPI stuff */
+ ATAPI_PKT_DMA = (1 << 0),
+ ATAPI_DMADIR = (1 << 2), /* ATAPI data dir:
+ 0=to device, 1=to host */
+ ATAPI_CDB_LEN = 16,
+
+ /* PMP stuff */
+ SATA_PMP_MAX_PORTS = 15,
+ SATA_PMP_CTRL_PORT = 15,
+
+ SATA_PMP_GSCR_DWORDS = 128,
+ SATA_PMP_GSCR_PROD_ID = 0,
+ SATA_PMP_GSCR_REV = 1,
+ SATA_PMP_GSCR_PORT_INFO = 2,
+ SATA_PMP_GSCR_ERROR = 32,
+ SATA_PMP_GSCR_ERROR_EN = 33,
+ SATA_PMP_GSCR_FEAT = 64,
+ SATA_PMP_GSCR_FEAT_EN = 96,
+
+ SATA_PMP_PSCR_STATUS = 0,
+ SATA_PMP_PSCR_ERROR = 1,
+ SATA_PMP_PSCR_CONTROL = 2,
+
+ SATA_PMP_FEAT_BIST = (1 << 0),
+ SATA_PMP_FEAT_PMREQ = (1 << 1),
+ SATA_PMP_FEAT_DYNSSC = (1 << 2),
+ SATA_PMP_FEAT_NOTIFY = (1 << 3),
+
+ /* cable types */
+ ATA_CBL_NONE = 0,
+ ATA_CBL_PATA40 = 1,
+ ATA_CBL_PATA80 = 2,
+ ATA_CBL_PATA40_SHORT = 3, /* 40 wire cable to high UDMA spec */
+ ATA_CBL_PATA_UNK = 4, /* don't know, maybe 80c? */
+ ATA_CBL_PATA_IGN = 5, /* don't know, ignore cable handling */
+ ATA_CBL_SATA = 6,
+
+ /* SATA Status and Control Registers */
+ SCR_STATUS = 0,
+ SCR_ERROR = 1,
+ SCR_CONTROL = 2,
+ SCR_ACTIVE = 3,
+ SCR_NOTIFICATION = 4,
+
+ /* SError bits */
+ SERR_DATA_RECOVERED = (1 << 0), /* recovered data error */
+ SERR_COMM_RECOVERED = (1 << 1), /* recovered comm failure */
+ SERR_DATA = (1 << 8), /* unrecovered data error */
+ SERR_PERSISTENT = (1 << 9), /* persistent data/comm error */
+ SERR_PROTOCOL = (1 << 10), /* protocol violation */
+ SERR_INTERNAL = (1 << 11), /* host internal error */
+ SERR_PHYRDY_CHG = (1 << 16), /* PHY RDY changed */
+ SERR_PHY_INT_ERR = (1 << 17), /* PHY internal error */
+ SERR_COMM_WAKE = (1 << 18), /* Comm wake */
+ SERR_10B_8B_ERR = (1 << 19), /* 10b to 8b decode error */
+ SERR_DISPARITY = (1 << 20), /* Disparity */
+ SERR_CRC = (1 << 21), /* CRC error */
+ SERR_HANDSHAKE = (1 << 22), /* Handshake error */
+ SERR_LINK_SEQ_ERR = (1 << 23), /* Link sequence error */
+ SERR_TRANS_ST_ERROR = (1 << 24), /* Transport state trans. error */
+ SERR_UNRECOG_FIS = (1 << 25), /* Unrecognized FIS */
+ SERR_DEV_XCHG = (1 << 26), /* device exchanged */
+
+ /* struct ata_taskfile flags */
+ ATA_TFLAG_LBA48 = (1 << 0), /* enable 48-bit LBA and "HOB" */
+ ATA_TFLAG_ISADDR = (1 << 1), /* enable r/w to nsect/lba regs */
+ ATA_TFLAG_DEVICE = (1 << 2), /* enable r/w to device reg */
+ ATA_TFLAG_WRITE = (1 << 3), /* data dir: host->dev==1 (write) */
+ ATA_TFLAG_LBA = (1 << 4), /* enable LBA */
+ ATA_TFLAG_FUA = (1 << 5), /* enable FUA */
+ ATA_TFLAG_POLLING = (1 << 6), /* set nIEN to 1 and use polling */
+
+ /* protocol flags */
+ ATA_PROT_FLAG_PIO = (1 << 0), /* is PIO */
+ ATA_PROT_FLAG_DMA = (1 << 1), /* is DMA */
+ ATA_PROT_FLAG_DATA = ATA_PROT_FLAG_PIO | ATA_PROT_FLAG_DMA,
+ ATA_PROT_FLAG_NCQ = (1 << 2), /* is NCQ */
+ ATA_PROT_FLAG_ATAPI = (1 << 3), /* is ATAPI */
};
+enum ata_tf_protocols {
+ /* ATA taskfile protocols */
+ ATA_PROT_UNKNOWN, /* unknown/invalid */
+ ATA_PROT_NODATA, /* no data */
+ ATA_PROT_PIO, /* PIO data xfer */
+ ATA_PROT_DMA, /* DMA */
+ ATA_PROT_NCQ, /* NCQ */
+ ATAPI_PROT_NODATA, /* packet command, no data */
+ ATAPI_PROT_PIO, /* packet command, PIO data xfer*/
+ ATAPI_PROT_DMA, /* packet command with special DMA sauce */
+};
+
+enum ata_ioctls {
+ ATA_IOC_GET_IO32 = 0x309,
+ ATA_IOC_SET_IO32 = 0x324,
+};
+
+enum ata_dev_typed {
+ ATA_DEV_ATA, /* ATA device */
+ ATA_DEV_ATAPI, /* ATAPI device */
+ ATA_DEV_PMP, /* Port Multiplier Port */
+ ATA_DEV_UNKNOWN, /* unknown */
+};
+
+struct ata_taskfile {
+ unsigned long flags; /* ATA_TFLAG_xxx */
+ u8 protocol; /* ATA_PROT_xxx */
+
+ u8 ctl; /* control reg */
+
+ u8 hob_feature; /* additional data */
+ u8 hob_nsect; /* to support LBA48 */
+ u8 hob_lbal;
+ u8 hob_lbam;
+ u8 hob_lbah;
+
+ u8 feature;
+ u8 nsect;
+ u8 lbal;
+ u8 lbam;
+ u8 lbah;
+
+ u8 device;
+
+ u8 command; /* IO operation */
+};
+
+/*
+ * protocol tests
+ */
+static inline unsigned int ata_prot_flags(u8 prot)
+{
+ switch (prot) {
+ case ATA_PROT_NODATA:
+ return 0;
+ case ATA_PROT_PIO:
+ return ATA_PROT_FLAG_PIO;
+ case ATA_PROT_DMA:
+ return ATA_PROT_FLAG_DMA;
+ case ATA_PROT_NCQ:
+ return ATA_PROT_FLAG_DMA | ATA_PROT_FLAG_NCQ;
+ case ATAPI_PROT_NODATA:
+ return ATA_PROT_FLAG_ATAPI;
+ case ATAPI_PROT_PIO:
+ return ATA_PROT_FLAG_ATAPI | ATA_PROT_FLAG_PIO;
+ case ATAPI_PROT_DMA:
+ return ATA_PROT_FLAG_ATAPI | ATA_PROT_FLAG_DMA;
+ }
+ return 0;
+}
+
+static inline int ata_is_atapi(u8 prot)
+{
+ return ata_prot_flags(prot) & ATA_PROT_FLAG_ATAPI;
+}
+
+static inline int ata_is_nodata(u8 prot)
+{
+ return !(ata_prot_flags(prot) & ATA_PROT_FLAG_DATA);
+}
+
+static inline int ata_is_pio(u8 prot)
+{
+ return ata_prot_flags(prot) & ATA_PROT_FLAG_PIO;
+}
+
+static inline int ata_is_dma(u8 prot)
+{
+ return ata_prot_flags(prot) & ATA_PROT_FLAG_DMA;
+}
+
+static inline int ata_is_ncq(u8 prot)
+{
+ return ata_prot_flags(prot) & ATA_PROT_FLAG_NCQ;
+}
+
+static inline int ata_is_data(u8 prot)
+{
+ return ata_prot_flags(prot) & ATA_PROT_FLAG_DATA;
+}
+
+/*
+ * id tests
+ */
#define ata_id_is_ata(id) (((id)[0] & (1 << 15)) == 0)
-#define ata_id_wcache_enabled(id) ((id)[85] & (1 << 5))
-#define ata_id_has_fua(id) ((id)[84] & (1 << 6))
-#define ata_id_has_flush(id) ((id)[83] & (1 << 12))
-#define ata_id_has_flush_ext(id) ((id)[83] & (1 << 13))
-#define ata_id_has_lba48(id) ((id)[83] & (1 << 10))
-#define ata_id_has_wcache(id) ((id)[82] & (1 << 5))
#define ata_id_has_lba(id) ((id)[49] & (1 << 9))
#define ata_id_has_dma(id) ((id)[49] & (1 << 8))
#define ata_id_has_ncq(id) ((id)[76] & (1 << 8))
#define ata_id_queue_depth(id) (((id)[75] & 0x1f) + 1)
+#define ata_id_removeable(id) ((id)[0] & (1 << 7))
+#define ata_id_iordy_disable(id) ((id)[49] & (1 << 10))
+#define ata_id_has_iordy(id) ((id)[49] & (1 << 11))
#define ata_id_u32(id,n) \
(((u32) (id)[(n) + 1] << 16) | ((u32) (id)[(n)]))
@@ -176,6 +454,80 @@
((u64) (id)[(n) + 1] << 16) | \
((u64) (id)[(n) + 0]) )
+#define ata_id_cdb_intr(id) (((id)[0] & 0x60) == 0x20)
+
+static inline int ata_id_has_fua(const u16 *id)
+{
+ if ((id[84] & 0xC000) != 0x4000)
+ return 0;
+ return id[84] & (1 << 6);
+}
+
+static inline int ata_id_has_flush(const u16 *id)
+{
+ if ((id[83] & 0xC000) != 0x4000)
+ return 0;
+ return id[83] & (1 << 12);
+}
+
+static inline int ata_id_has_flush_ext(const u16 *id)
+{
+ if ((id[83] & 0xC000) != 0x4000)
+ return 0;
+ return id[83] & (1 << 13);
+}
+
+static inline int ata_id_has_lba48(const u16 *id)
+{
+ if ((id[83] & 0xC000) != 0x4000)
+ return 0;
+ if (!ata_id_u64(id, 100))
+ return 0;
+ return id[83] & (1 << 10);
+}
+
+static inline int ata_id_hpa_enabled(const u16 *id)
+{
+ /* Yes children, word 83 valid bits cover word 82 data */
+ if ((id[83] & 0xC000) != 0x4000)
+ return 0;
+ /* And 87 covers 85-87 */
+ if ((id[87] & 0xC000) != 0x4000)
+ return 0;
+ /* Check command sets enabled as well as supported */
+ if ((id[85] & ( 1 << 10)) == 0)
+ return 0;
+ return id[82] & (1 << 10);
+}
+
+static inline int ata_id_has_wcache(const u16 *id)
+{
+ /* Yes children, word 83 valid bits cover word 82 data */
+ if ((id[83] & 0xC000) != 0x4000)
+ return 0;
+ return id[82] & (1 << 5);
+}
+
+static inline int ata_id_has_pm(const u16 *id)
+{
+ if ((id[83] & 0xC000) != 0x4000)
+ return 0;
+ return id[82] & (1 << 3);
+}
+
+static inline int ata_id_rahead_enabled(const u16 *id)
+{
+ if ((id[87] & 0xC000) != 0x4000)
+ return 0;
+ return id[85] & (1 << 6);
+}
+
+static inline int ata_id_wcache_enabled(const u16 *id)
+{
+ if ((id[87] & 0xC000) != 0x4000)
+ return 0;
+ return id[85] & (1 << 5);
+}
static inline unsigned int ata_id_major_version(const u16 *id)
{
@@ -195,6 +547,118 @@
return ata_id_major_version(id) >= 5 && id[93] == 0;
}
+static inline int ata_id_has_tpm(const u16 *id)
+{
+ /* The TPM bits are only valid on ATA8 */
+ if (ata_id_major_version(id) < 8)
+ return 0;
+ if ((id[48] & 0xC000) != 0x4000)
+ return 0;
+ return id[48] & (1 << 0);
+}
+
+static inline int ata_id_has_dword_io(const u16 *id)
+{
+ /* ATA 8 reuses this flag for "trusted" computing */
+ if (ata_id_major_version(id) > 7)
+ return 0;
+ if (id[48] & (1 << 0))
+ return 1;
+ return 0;
+}
+
+static inline int ata_id_current_chs_valid(const u16 *id)
+{
+ /* For ATA-1 devices, if the INITIALIZE DEVICE PARAMETERS command
+ has not been issued to the device then the values of
+ id[54] to id[56] are vendor specific. */
+ return (id[53] & 0x01) && /* Current translation valid */
+ id[54] && /* cylinders in current translation */
+ id[55] && /* heads in current translation */
+ id[55] <= 16 &&
+ id[56]; /* sectors in current translation */
+}
+
+static inline int ata_id_is_cfa(const u16 *id)
+{
+ u16 v = id[0];
+ if (v == 0x848A) /* Standard CF */
+ return 1;
+ /* Could be CF hiding as standard ATA */
+ if (ata_id_major_version(id) >= 3 && id[82] != 0xFFFF &&
+ (id[82] & ( 1 << 2)))
+ return 1;
+ return 0;
+}
+
+static inline int ata_drive_40wire(const u16 *dev_id)
+{
+ if (ata_id_is_sata(dev_id))
+ return 0; /* SATA */
+ if ((dev_id[93] & 0xE000) == 0x6000)
+ return 0; /* 80 wire */
+ return 1;
+}
+
+static inline int ata_drive_40wire_relaxed(const u16 *dev_id)
+{
+ if ((dev_id[93] & 0x2000) == 0x2000)
+ return 0; /* 80 wire */
+ return 1;
+}
+
+static inline int atapi_cdb_len(const u16 *dev_id)
+{
+ u16 tmp = dev_id[0] & 0x3;
+ switch (tmp) {
+ case 0: return 12;
+ case 1: return 16;
+ default: return -1;
+ }
+}
+
+static inline int atapi_command_packet_set(const u16 *dev_id)
+{
+ return (dev_id[0] >> 8) & 0x1f;
+}
+
+static inline int atapi_id_dmadir(const u16 *dev_id)
+{
+ return ata_id_major_version(dev_id) >= 7 && (dev_id[62] & 0x8000);
+}
+
+static inline int is_multi_taskfile(struct ata_taskfile *tf)
+{
+ return (tf->command == ATA_CMD_READ_MULTI) ||
+ (tf->command == ATA_CMD_WRITE_MULTI) ||
+ (tf->command == ATA_CMD_READ_MULTI_EXT) ||
+ (tf->command == ATA_CMD_WRITE_MULTI_EXT) ||
+ (tf->command == ATA_CMD_WRITE_MULTI_FUA_EXT);
+}
+
+static inline int ata_ok(u8 status)
+{
+ return ((status & (ATA_BUSY | ATA_DRDY | ATA_DF | ATA_DRQ | ATA_ERR))
+ == ATA_DRDY);
+}
+
+static inline int lba_28_ok(u64 block, u32 n_block)
+{
+ /* check the ending block number */
+ return ((block + n_block - 1) < ((u64)1 << 28)) && (n_block <= 256);
+}
+
+static inline int lba_48_ok(u64 block, u32 n_block)
+{
+ /* check the ending block number */
+ return ((block + n_block - 1) < ((u64)1 << 48)) && (n_block <= 65536);
+}
+
+#define sata_pmp_gscr_vendor(gscr) ((gscr)[SATA_PMP_GSCR_PROD_ID] & 0xffff)
+#define sata_pmp_gscr_devid(gscr) ((gscr)[SATA_PMP_GSCR_PROD_ID] >> 16)
+#define sata_pmp_gscr_rev(gscr) (((gscr)[SATA_PMP_GSCR_REV] >> 8) & 0xff)
+#define sata_pmp_gscr_ports(gscr) ((gscr)[SATA_PMP_GSCR_PORT_INFO] & 0xf)
+
u64 ata_id_n_sectors(u16 *id);
u32 ata_dev_classify(u32 sig);
void ata_id_c_string(const u16 *id, unsigned char *s,