* Patch by Martin Krause, 17 Jul 2003:
add delay to get I2C working with "imm" command and s3c24x0_i2c.c
* Patch by Richard Woodruff, 17 July 03:
- Fixed bug in OMAP1510 baud rate divisor settings.
* Patch by Nye Liu, 16 July 2003:
MPC860FADS fixes:
- add MPC86xADS support (uses MPC86xADS.h)
- add 866P/T core support (also MPC859T/MPC859DSL/MPC852T)
o PLPRCR changes
o BRG changes (EXTAL/XTAL restricted to 10MHz)
o don't trust gclk() software measurement by default, depend on
CONFIG_8xx_GCLK_FREQ
- add DRAM SIMM not installed detection
- use more "correct" SDRAM initialization sequence
- allow different SDRAM sizes (8xxADS has 8M)
- default DER is 0
- remove unused MAMR defines from FADS860T.h (all done in fads.c)
- rename MAMR/MBMR defines to be more consistent. Should eventually
be merged into MxMR to better reflect the PowerQUICC datasheet.
* Patch by Yuli Barcohen, 16 Jul 2003:
support new Motorola PQ2FADS-ZU evaluation board which replaced
MPC8260ADS and MPC8266ADS
diff --git a/README b/README
index 8b2b1af..1c40711 100644
--- a/README
+++ b/README
@@ -197,7 +197,7 @@
- board/lwmon Files specific to LWMON boards
- board/mbx8xx Files specific to MBX boards
- board/mpc8260ads
- Files specific to MMPC8260ADS boards
+ Files specific to MPC8260ADS and PQ2FADS-ZU boards
- board/mpl/ Files specific to boards manufactured by MPL
- board/mpl/common Common files for MPL boards
- board/mpl/pip405 Files specific to PIP405 boards
@@ -383,6 +383,14 @@
the lcd display every second with
a "rotator" |\-/|\-/
+- Board flavour: (if CONFIG_MPC8260ADS is defined)
+ CONFIG_ADSTYPE
+ Possible values are:
+ CFG_8260ADS - original MPC8260ADS
+ CFG_8266ADS - MPC8266ADS (untested)
+ CFG_PQ2FADS - PQ2FADS-ZU
+
+
- MPC824X Family Member (if CONFIG_MPC824X is defined)
Define exactly one of
CONFIG_MPC8240, CONFIG_MPC8245
@@ -989,8 +997,8 @@
is FALSE, it clears it (low).
eg: #define I2C_SDA(bit) \
- if(bit) immr->im_cpm.cp_pbdat |= PB_SDA; \
- else immr->im_cpm.cp_pbdat &= ~PB_SDA
+ if(bit) immr->im_cpm.cp_pbdat |= PB_SDA; \
+ else immr->im_cpm.cp_pbdat &= ~PB_SDA
I2C_SCL(bit)
@@ -998,8 +1006,8 @@
is FALSE, it clears it (low).
eg: #define I2C_SCL(bit) \
- if(bit) immr->im_cpm.cp_pbdat |= PB_SCL; \
- else immr->im_cpm.cp_pbdat &= ~PB_SCL
+ if(bit) immr->im_cpm.cp_pbdat |= PB_SCL; \
+ else immr->im_cpm.cp_pbdat &= ~PB_SCL
I2C_DELAY
@@ -1687,9 +1695,10 @@
- CFG_DEFAULT_IMMR:
Default address of the IMMR after system reset.
- Needed on some 8260 systems (MPC8260ADS and RPXsuper)
- to be able to adjust the position of the IMMR
- register after a reset.
+
+ Needed on some 8260 systems (MPC8260ADS, PQ2FADS-ZU,
+ and RPXsuper) to be able to adjust the position of
+ the IMMR register after a reset.
- Floppy Disk Support:
CFG_FDC_DRIVE_NUMBER
@@ -1862,7 +1871,7 @@
GENIETV_config TQM823L_config PIP405_config
GEN860T_config EBONY_config FPS860L_config
ELPT860_config cmi_mpc5xx_config NETVIA_config
- at91rm9200dk_config omap1510inn_config
+ at91rm9200dk_config omap1510inn_config MPC8260ADS_config
Note: for some board special configuration names may exist; check if
additional information is available from the board vendor; for