mips: jz47xx: Add Creator CI20 platform
Add support for the Creator CI20 platform based on the JZ4780 SoC.
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Reviewed-by: Marek Vasut <marex@denx.de>
diff --git a/board/imgtec/ci20/Kconfig b/board/imgtec/ci20/Kconfig
new file mode 100644
index 0000000..82bf65d
--- /dev/null
+++ b/board/imgtec/ci20/Kconfig
@@ -0,0 +1,15 @@
+if TARGET_JZ4780_CI20
+
+config SYS_BOARD
+ default "ci20"
+
+config SYS_VENDOR
+ default "imgtec"
+
+config SYS_CONFIG_NAME
+ default "ci20"
+
+config SYS_TEXT_BASE
+ default 0x80000000
+
+endif
diff --git a/board/imgtec/ci20/MAINTAINERS b/board/imgtec/ci20/MAINTAINERS
new file mode 100644
index 0000000..dca6bf3
--- /dev/null
+++ b/board/imgtec/ci20/MAINTAINERS
@@ -0,0 +1,6 @@
+Creator CI20 BOARD
+M: Ezequiel Garcia <ezequiel@collabora.com>
+S: Maintained
+F: board/imgtec/ci20/
+F: include/configs/ci20.h
+F: configs/ci20_mmc_defconfig
diff --git a/board/imgtec/ci20/Makefile b/board/imgtec/ci20/Makefile
new file mode 100644
index 0000000..7843b46
--- /dev/null
+++ b/board/imgtec/ci20/Makefile
@@ -0,0 +1,3 @@
+# SPDX-License-Identifier: GPL-2.0+
+
+obj-y := ci20.o
diff --git a/board/imgtec/ci20/README b/board/imgtec/ci20/README
new file mode 100644
index 0000000..07d89d7
--- /dev/null
+++ b/board/imgtec/ci20/README
@@ -0,0 +1,10 @@
+CI20 U-Boot
+
+Installation to an SD card:
+ Repartition your card with an MBR such that the first partition starts at an
+ offset of no less than 270KB. Then install U-Boot SPL & the full U-Boot image
+ to the card like so:
+
+ dd if=spl/u-boot-spl.bin of=/dev/sdX obs=512 seek=1
+ dd if=u-boot-dtb.img of=/dev/sdX obs=1K seek=14
+ sync
diff --git a/board/imgtec/ci20/ci20.c b/board/imgtec/ci20/ci20.c
new file mode 100644
index 0000000..9811ef5
--- /dev/null
+++ b/board/imgtec/ci20/ci20.c
@@ -0,0 +1,362 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * CI20 setup code
+ *
+ * Copyright (c) 2013 Imagination Technologies
+ * Author: Paul Burton <paul.burton@imgtec.com>
+ */
+
+#include <common.h>
+#include <environment.h>
+#include <net.h>
+#include <netdev.h>
+#include <asm/io.h>
+#include <asm/gpio.h>
+#include <mach/jz4780.h>
+#include <mach/jz4780_dram.h>
+#include <mach/jz4780_gpio.h>
+
+struct ci20_otp {
+ u32 serial_number;
+ u32 date;
+ u8 manufacturer[2];
+ u8 mac[6];
+} __packed;
+
+static void ci20_mux_mmc(void)
+{
+ void __iomem *gpio_regs = (void __iomem *)GPIO_BASE;
+
+ /* setup MSC1 pins */
+ writel(0x30f00000, gpio_regs + GPIO_PXINTC(4));
+ writel(0x30f00000, gpio_regs + GPIO_PXMASKC(4));
+ writel(0x30f00000, gpio_regs + GPIO_PXPAT1C(4));
+ writel(0x30f00000, gpio_regs + GPIO_PXPAT0C(4));
+ writel(0x30f00000, gpio_regs + GPIO_PXPENC(4));
+ jz4780_clk_ungate_mmc();
+}
+
+#ifndef CONFIG_SPL_BUILD
+
+static void ci20_mux_eth(void)
+{
+ void __iomem *gpio_regs = (void __iomem *)GPIO_BASE;
+
+#ifdef CONFIG_NAND
+ /* setup pins (some already setup for NAND) */
+ writel(0x04030000, gpio_regs + GPIO_PXINTC(0));
+ writel(0x04030000, gpio_regs + GPIO_PXMASKC(0));
+ writel(0x04030000, gpio_regs + GPIO_PXPAT1C(0));
+ writel(0x04030000, gpio_regs + GPIO_PXPAT0C(0));
+ writel(0x04030000, gpio_regs + GPIO_PXPENS(0));
+#else
+ /* setup pins (as above +NAND CS +RD/WE +SDx +SAx) */
+ writel(0x0dff00ff, gpio_regs + GPIO_PXINTC(0));
+ writel(0x0dff00ff, gpio_regs + GPIO_PXMASKC(0));
+ writel(0x0dff00ff, gpio_regs + GPIO_PXPAT1C(0));
+ writel(0x0dff00ff, gpio_regs + GPIO_PXPAT0C(0));
+ writel(0x0dff00ff, gpio_regs + GPIO_PXPENS(0));
+ writel(0x00000003, gpio_regs + GPIO_PXINTC(1));
+ writel(0x00000003, gpio_regs + GPIO_PXMASKC(1));
+ writel(0x00000003, gpio_regs + GPIO_PXPAT1C(1));
+ writel(0x00000003, gpio_regs + GPIO_PXPAT0C(1));
+ writel(0x00000003, gpio_regs + GPIO_PXPENS(1));
+#endif
+}
+
+static void ci20_mux_jtag(void)
+{
+#ifdef CONFIG_JTAG
+ void __iomem *gpio_regs = (void __iomem *)GPIO_BASE;
+
+ /* enable JTAG */
+ writel(3 << 30, gpio_regs + GPIO_PXINTC(0));
+ writel(3 << 30, gpio_regs + GPIO_PXMASKC(0));
+ writel(3 << 30, gpio_regs + GPIO_PXPAT1C(0));
+ writel(3 << 30, gpio_regs + GPIO_PXPAT0C(0));
+#endif
+}
+
+static void ci20_mux_nand(void)
+{
+ void __iomem *gpio_regs = (void __iomem *)GPIO_BASE;
+
+ /* setup pins */
+ writel(0x002c00ff, gpio_regs + GPIO_PXINTC(0));
+ writel(0x002c00ff, gpio_regs + GPIO_PXMASKC(0));
+ writel(0x002c00ff, gpio_regs + GPIO_PXPAT1C(0));
+ writel(0x002c00ff, gpio_regs + GPIO_PXPAT0C(0));
+ writel(0x002c00ff, gpio_regs + GPIO_PXPENS(0));
+ writel(0x00000003, gpio_regs + GPIO_PXINTC(1));
+ writel(0x00000003, gpio_regs + GPIO_PXMASKC(1));
+ writel(0x00000003, gpio_regs + GPIO_PXPAT1C(1));
+ writel(0x00000003, gpio_regs + GPIO_PXPAT0C(1));
+ writel(0x00000003, gpio_regs + GPIO_PXPENS(1));
+
+ /* FRB0_N */
+ jz47xx_gpio_direction_input(JZ_GPIO(0, 20));
+ writel(20, gpio_regs + GPIO_PXPENS(0));
+
+ /* disable write protect */
+ jz47xx_gpio_direction_output(JZ_GPIO(5, 22), 1);
+}
+
+static void ci20_mux_uart(void)
+{
+ void __iomem *gpio_regs = (void __iomem *)GPIO_BASE;
+
+ /* UART0 */
+ writel(0x9, gpio_regs + GPIO_PXINTC(5));
+ writel(0x9, gpio_regs + GPIO_PXMASKC(5));
+ writel(0x9, gpio_regs + GPIO_PXPAT1C(5));
+ writel(0x9, gpio_regs + GPIO_PXPAT0C(5));
+ writel(0x9, gpio_regs + GPIO_PXPENC(5));
+ jz4780_clk_ungate_uart(0);
+
+ /* UART 1 and 2 */
+ jz4780_clk_ungate_uart(1);
+ jz4780_clk_ungate_uart(2);
+
+#ifndef CONFIG_JTAG
+ /* UART3 */
+ writel(1 << 12, gpio_regs + GPIO_PXINTC(3));
+ writel(1 << 12, gpio_regs + GPIO_PXMASKS(3));
+ writel(1 << 12, gpio_regs + GPIO_PXPAT1S(3));
+ writel(1 << 12, gpio_regs + GPIO_PXPAT0C(3));
+ writel(3 << 30, gpio_regs + GPIO_PXINTC(0));
+ writel(3 << 30, gpio_regs + GPIO_PXMASKC(0));
+ writel(3 << 30, gpio_regs + GPIO_PXPAT1C(0));
+ writel(1 << 30, gpio_regs + GPIO_PXPAT0C(0));
+ writel(1 << 31, gpio_regs + GPIO_PXPAT0S(0));
+ jz4780_clk_ungate_uart(3);
+#endif
+
+ /* UART4 */
+ writel(0x100400, gpio_regs + GPIO_PXINTC(2));
+ writel(0x100400, gpio_regs + GPIO_PXMASKC(2));
+ writel(0x100400, gpio_regs + GPIO_PXPAT1S(2));
+ writel(0x100400, gpio_regs + GPIO_PXPAT0C(2));
+ writel(0x100400, gpio_regs + GPIO_PXPENC(2));
+ jz4780_clk_ungate_uart(4);
+}
+
+int board_early_init_f(void)
+{
+ ci20_mux_jtag();
+ ci20_mux_uart();
+
+ ci20_mux_eth();
+ ci20_mux_mmc();
+ ci20_mux_nand();
+
+ /* SYS_POWER_IND high (LED blue, VBUS off) */
+ jz47xx_gpio_direction_output(JZ_GPIO(5, 15), 0);
+
+ /* LEDs off */
+ jz47xx_gpio_direction_output(JZ_GPIO(2, 0), 0);
+ jz47xx_gpio_direction_output(JZ_GPIO(2, 1), 0);
+ jz47xx_gpio_direction_output(JZ_GPIO(2, 2), 0);
+ jz47xx_gpio_direction_output(JZ_GPIO(2, 3), 0);
+
+ return 0;
+}
+
+int misc_init_r(void)
+{
+ const u32 efuse_clk = jz4780_clk_get_efuse_clk();
+ struct ci20_otp otp;
+ char manufacturer[3];
+
+ /* Read the board OTP data */
+ jz4780_efuse_init(efuse_clk);
+ jz4780_efuse_read(0x18, 16, (u8 *)&otp);
+
+ /* Set MAC address */
+ if (!is_valid_ethaddr(otp.mac)) {
+ /* no MAC assigned, generate one from the unique chip ID */
+ jz4780_efuse_read(0x8, 4, &otp.mac[0]);
+ jz4780_efuse_read(0x12, 2, &otp.mac[4]);
+ otp.mac[0] = (otp.mac[0] | 0x02) & ~0x01;
+ }
+ eth_env_set_enetaddr("ethaddr", otp.mac);
+
+ /* Put other board information into the environment */
+ env_set_ulong("serial#", otp.serial_number);
+ env_set_ulong("board_date", otp.date);
+ manufacturer[0] = otp.manufacturer[0];
+ manufacturer[1] = otp.manufacturer[1];
+ manufacturer[2] = 0;
+ env_set("board_mfr", manufacturer);
+
+ return 0;
+}
+
+#ifdef CONFIG_DRIVER_DM9000
+int board_eth_init(bd_t *bis)
+{
+ /* Enable clock */
+ jz4780_clk_ungate_ethernet();
+
+ /* Enable power (PB25) */
+ jz47xx_gpio_direction_output(JZ_GPIO(1, 25), 1);
+
+ /* Reset (PF12) */
+ mdelay(10);
+ jz47xx_gpio_direction_output(JZ_GPIO(5, 12), 0);
+ mdelay(10);
+ jz47xx_gpio_direction_output(JZ_GPIO(5, 12), 1);
+ mdelay(10);
+
+ return dm9000_initialize(bis);
+}
+#endif /* CONFIG_DRIVER_DM9000 */
+#endif
+
+static u8 ci20_revision(void)
+{
+ void __iomem *gpio_regs = (void __iomem *)GPIO_BASE;
+ int val;
+
+ jz47xx_gpio_direction_input(JZ_GPIO(2, 18));
+ jz47xx_gpio_direction_input(JZ_GPIO(2, 19));
+
+ /* Enable pullups */
+ writel(BIT(18) | BIT(19), gpio_regs + GPIO_PXPENC(2));
+
+ /* Read PC18/19 for version */
+ val = (!!jz47xx_gpio_get_value(JZ_GPIO(2, 18))) |
+ ((!!jz47xx_gpio_get_value(JZ_GPIO(2, 19))) << 1);
+
+ if (val == 3) /* Rev 1 boards had no pulldowns - giving 3 */
+ return 1;
+ if (val == 1) /* Rev 2 boards pulldown port C bit 18 giving 1 */
+ return 2;
+
+ return 0;
+}
+
+int dram_init(void)
+{
+ gd->ram_size = sdram_size(0) + sdram_size(1);
+ return 0;
+}
+
+/* U-Boot common routines */
+int checkboard(void)
+{
+ printf("Board: Creator CI20 (rev.%d)\n", ci20_revision());
+ return 0;
+}
+
+#ifdef CONFIG_SPL_BUILD
+
+#if defined(CONFIG_SPL_MMC_SUPPORT)
+int board_mmc_init(bd_t *bd)
+{
+ ci20_mux_mmc();
+ return jz_mmc_init((void __iomem *)MSC0_BASE);
+}
+#endif
+
+static const struct jz4780_ddr_config K4B2G0846Q_48_config = {
+ .timing = {
+ (4 << DDRC_TIMING1_TRTP_BIT) | (13 << DDRC_TIMING1_TWTR_BIT) |
+ (6 << DDRC_TIMING1_TWR_BIT) | (5 << DDRC_TIMING1_TWL_BIT),
+
+ (4 << DDRC_TIMING2_TCCD_BIT) | (15 << DDRC_TIMING2_TRAS_BIT) |
+ (6 << DDRC_TIMING2_TRCD_BIT) | (6 << DDRC_TIMING2_TRL_BIT),
+
+ (4 << DDRC_TIMING3_ONUM) | (7 << DDRC_TIMING3_TCKSRE_BIT) |
+ (6 << DDRC_TIMING3_TRP_BIT) | (4 << DDRC_TIMING3_TRRD_BIT) |
+ (21 << DDRC_TIMING3_TRC_BIT),
+
+ (31 << DDRC_TIMING4_TRFC_BIT) | (1 << DDRC_TIMING4_TRWCOV_BIT) |
+ (4 << DDRC_TIMING4_TCKE_BIT) | (9 << DDRC_TIMING4_TMINSR_BIT) |
+ (8 << DDRC_TIMING4_TXP_BIT) | (3 << DDRC_TIMING4_TMRD_BIT),
+
+ (8 << DDRC_TIMING5_TRTW_BIT) | (4 << DDRC_TIMING5_TRDLAT_BIT) |
+ (4 << DDRC_TIMING5_TWDLAT_BIT),
+
+ (25 << DDRC_TIMING6_TXSRD_BIT) | (12 << DDRC_TIMING6_TFAW_BIT) |
+ (2 << DDRC_TIMING6_TCFGW_BIT) | (2 << DDRC_TIMING6_TCFGR_BIT),
+ },
+
+ /* PHY */
+ /* Mode Register 0 */
+ .mr0 = 0x420,
+#ifdef SDRAM_DISABLE_DLL
+ .mr1 = (DDR3_MR1_DIC_7 | DDR3_MR1_RTT_DIS | DDR3_MR1_DLL_DISABLE),
+#else
+ .mr1 = (DDR3_MR1_DIC_7 | DDR3_MR1_RTT_DIS),
+#endif
+
+ .ptr0 = 0x002000d4,
+ .ptr1 = 0x02230d40,
+ .ptr2 = 0x04013880,
+
+ .dtpr0 = 0x2a8f6690,
+ .dtpr1 = 0x00400860,
+ .dtpr2 = 0x10042a00,
+
+ .pullup = 0x0b,
+ .pulldn = 0x0b,
+};
+
+static const struct jz4780_ddr_config H5TQ2G83CFR_48_config = {
+ .timing = {
+ (4 << DDRC_TIMING1_TRTP_BIT) | (13 << DDRC_TIMING1_TWTR_BIT) |
+ (6 << DDRC_TIMING1_TWR_BIT) | (5 << DDRC_TIMING1_TWL_BIT),
+
+ (4 << DDRC_TIMING2_TCCD_BIT) | (16 << DDRC_TIMING2_TRAS_BIT) |
+ (6 << DDRC_TIMING2_TRCD_BIT) | (6 << DDRC_TIMING2_TRL_BIT),
+
+ (4 << DDRC_TIMING3_ONUM) | (7 << DDRC_TIMING3_TCKSRE_BIT) |
+ (6 << DDRC_TIMING3_TRP_BIT) | (4 << DDRC_TIMING3_TRRD_BIT) |
+ (22 << DDRC_TIMING3_TRC_BIT),
+
+ (42 << DDRC_TIMING4_TRFC_BIT) | (1 << DDRC_TIMING4_TRWCOV_BIT) |
+ (4 << DDRC_TIMING4_TCKE_BIT) | (7 << DDRC_TIMING4_TMINSR_BIT) |
+ (3 << DDRC_TIMING4_TXP_BIT) | (3 << DDRC_TIMING4_TMRD_BIT),
+
+ (8 << DDRC_TIMING5_TRTW_BIT) | (4 << DDRC_TIMING5_TRDLAT_BIT) |
+ (4 << DDRC_TIMING5_TWDLAT_BIT),
+
+ (25 << DDRC_TIMING6_TXSRD_BIT) | (20 << DDRC_TIMING6_TFAW_BIT) |
+ (2 << DDRC_TIMING6_TCFGW_BIT) | (2 << DDRC_TIMING6_TCFGR_BIT),
+ },
+
+ /* PHY */
+ /* Mode Register 0 */
+ .mr0 = 0x420,
+#ifdef SDRAM_DISABLE_DLL
+ .mr1 = (DDR3_MR1_DIC_7 | DDR3_MR1_RTT_DIS | DDR3_MR1_DLL_DISABLE),
+#else
+ .mr1 = (DDR3_MR1_DIC_7 | DDR3_MR1_RTT_DIS),
+#endif
+
+ .ptr0 = 0x002000d4,
+ .ptr1 = 0x02d30d40,
+ .ptr2 = 0x04013880,
+
+ .dtpr0 = 0x2c906690,
+ .dtpr1 = 0x005608a0,
+ .dtpr2 = 0x10042a00,
+
+ .pullup = 0x0e,
+ .pulldn = 0x0e,
+};
+
+#if (CONFIG_SYS_MHZ != 1200)
+#error No DDR configuration for CPU speed
+#endif
+
+const struct jz4780_ddr_config *jz4780_get_ddr_config(void)
+{
+ const int board_revision = ci20_revision();
+
+ if (board_revision == 2)
+ return &K4B2G0846Q_48_config;
+ else /* Fall back to H5TQ2G83CFR RAM */
+ return &H5TQ2G83CFR_48_config;
+}
+#endif