ARM: dts: at91: Add dts files for at91sam9x5ek
The device tree source files of at91sam9x5ek board are copied from
the Linux v4.10, do the changes below.
- Add the reg property for the pinctrl node.
- Move the gpio (pioA, pioB, pioC ...) nodes as the pinctrl's
slibling nodes, instead of the child nodes.
- Add the "u-boot,dm-pre-reloc" property to determine which nodes
are used by the board_init_f stage.
- Change the compatible of the spi flash to "spi-flash".
- Add the spi0 aliases.
- Fix the compilation warnings.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
diff --git a/arch/arm/dts/at91sam9x5_usart3.dtsi b/arch/arm/dts/at91sam9x5_usart3.dtsi
new file mode 100644
index 0000000..5259219
--- /dev/null
+++ b/arch/arm/dts/at91sam9x5_usart3.dtsi
@@ -0,0 +1,69 @@
+/*
+ * at91sam9x5_usart3.dtsi - Device Tree Include file for AT91SAM9x5 SoC with
+ * 4 USART.
+ *
+ * Copyright (C) 2013 Boris BREZILLON <b.brezillon@overkiz.com>
+ *
+ * Licensed under GPLv2.
+ */
+
+#include <dt-bindings/pinctrl/at91.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+
+/ {
+ aliases {
+ serial4 = &usart3;
+ };
+
+ ahb {
+ apb {
+ pinctrl@fffff400 {
+ usart3 {
+ pinctrl_usart3: usart3-0 {
+ atmel,pins =
+ <AT91_PIOC 22 AT91_PERIPH_B AT91_PINCTRL_PULL_UP /* PC22 periph B with pullup */
+ AT91_PIOC 23 AT91_PERIPH_B AT91_PINCTRL_NONE>; /* PC23 periph B */
+ };
+
+ pinctrl_usart3_rts: usart3_rts-0 {
+ atmel,pins =
+ <AT91_PIOC 24 AT91_PERIPH_B AT91_PINCTRL_NONE>; /* PC24 periph B */
+ };
+
+ pinctrl_usart3_cts: usart3_cts-0 {
+ atmel,pins =
+ <AT91_PIOC 25 AT91_PERIPH_B AT91_PINCTRL_NONE>; /* PC25 periph B */
+ };
+
+ pinctrl_usart3_sck: usart3_sck-0 {
+ atmel,pins =
+ <AT91_PIOC 26 AT91_PERIPH_B AT91_PINCTRL_NONE>; /* PC26 periph B */
+ };
+ };
+ };
+
+ pmc: pmc@fffffc00 {
+ periphck {
+ usart3_clk: usart3_clk@8 {
+ #clock-cells = <0>;
+ reg = <8>;
+ };
+ };
+ };
+
+ usart3: serial@f8028000 {
+ compatible = "atmel,at91sam9260-usart";
+ reg = <0xf8028000 0x200>;
+ interrupts = <8 IRQ_TYPE_LEVEL_HIGH 5>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usart3>;
+ dmas = <&dma1 1 AT91_DMA_CFG_PER_ID(14)>,
+ <&dma1 1 (AT91_DMA_CFG_PER_ID(15) | AT91_DMA_CFG_FIFOCFG_ASAP)>;
+ dma-names = "tx", "rx";
+ clocks = <&usart3_clk>;
+ clock-names = "usart";
+ status = "disabled";
+ };
+ };
+ };
+};