Merge git://git.denx.de/u-boot-mpc85xx
diff --git a/README b/README
index bfefa21..4ca04d0 100644
--- a/README
+++ b/README
@@ -409,6 +409,10 @@
Enables a workaround for IFC erratum A003399. It is only
requred during NOR boot.
+ CONFIG_A008044_WORKAROUND
+ Enables a workaround for T1040/T1042 erratum A008044. It is only
+ requred during NAND boot and valid for Rev 1.0 SoC revision
+
CONFIG_SYS_FSL_CORENET_SNOOPVEC_COREONLY
This is the value to write into CCSR offset 0x18600
diff --git a/arch/powerpc/cpu/mpc85xx/Kconfig b/arch/powerpc/cpu/mpc85xx/Kconfig
index 7b42d06..7501eb4 100644
--- a/arch/powerpc/cpu/mpc85xx/Kconfig
+++ b/arch/powerpc/cpu/mpc85xx/Kconfig
@@ -110,6 +110,14 @@
config TARGET_QEMU_PPCE500
bool "Support qemu-ppce500"
+config TARGET_T102XQDS
+ bool "Support T102xQDS"
+ select SUPPORT_SPL
+
+config TARGET_T102XRDB
+ bool "Support T102xRDB"
+ select SUPPORT_SPL
+
config TARGET_T1040QDS
bool "Support T1040QDS"
@@ -183,6 +191,8 @@
source "board/freescale/p2020ds/Kconfig"
source "board/freescale/p2041rdb/Kconfig"
source "board/freescale/qemu-ppce500/Kconfig"
+source "board/freescale/t102xqds/Kconfig"
+source "board/freescale/t102xrdb/Kconfig"
source "board/freescale/t1040qds/Kconfig"
source "board/freescale/t104xrdb/Kconfig"
source "board/freescale/t208xqds/Kconfig"
diff --git a/arch/powerpc/cpu/mpc85xx/Makefile b/arch/powerpc/cpu/mpc85xx/Makefile
index ad26b43..b93158b 100644
--- a/arch/powerpc/cpu/mpc85xx/Makefile
+++ b/arch/powerpc/cpu/mpc85xx/Makefile
@@ -51,6 +51,8 @@
obj-$(CONFIG_PPC_T1042) += t1040_ids.o
obj-$(CONFIG_PPC_T1020) += t1040_ids.o
obj-$(CONFIG_PPC_T1022) += t1040_ids.o
+obj-$(CONFIG_PPC_T1023) += t1024_ids.o
+obj-$(CONFIG_PPC_T1024) += t1024_ids.o
obj-$(CONFIG_PPC_T2080) += t2080_ids.o
obj-$(CONFIG_PPC_T2081) += t2080_ids.o
@@ -97,6 +99,8 @@
obj-$(CONFIG_PPC_T1042) += t1040_serdes.o
obj-$(CONFIG_PPC_T1020) += t1040_serdes.o
obj-$(CONFIG_PPC_T1022) += t1040_serdes.o
+obj-$(CONFIG_PPC_T1023) += t1024_serdes.o
+obj-$(CONFIG_PPC_T1024) += t1024_serdes.o
obj-$(CONFIG_PPC_T2080) += t2080_serdes.o
obj-$(CONFIG_PPC_T2081) += t2080_serdes.o
diff --git a/arch/powerpc/cpu/mpc85xx/b4860_ids.c b/arch/powerpc/cpu/mpc85xx/b4860_ids.c
index 1a30f1c..598f7bd 100644
--- a/arch/powerpc/cpu/mpc85xx/b4860_ids.c
+++ b/arch/powerpc/cpu/mpc85xx/b4860_ids.c
@@ -59,8 +59,8 @@
SET_PCI_LIODN(CONFIG_SYS_FSL_PCIE_COMPAT, 1, 148),
- SET_DMA_LIODN(1, 147),
- SET_DMA_LIODN(2, 227),
+ SET_DMA_LIODN(1, "fsl,elo3-dma", 147),
+ SET_DMA_LIODN(2, "fsl,elo3-dma", 227),
#ifndef CONFIG_PPC_B4420
SET_GUTS_LIODN("fsl,rapidio-delta", 199, rio1liodnr, 0),
diff --git a/arch/powerpc/cpu/mpc85xx/b4860_serdes.c b/arch/powerpc/cpu/mpc85xx/b4860_serdes.c
index cf18be5..63172de 100644
--- a/arch/powerpc/cpu/mpc85xx/b4860_serdes.c
+++ b/arch/powerpc/cpu/mpc85xx/b4860_serdes.c
@@ -18,6 +18,8 @@
#ifdef CONFIG_PPC_B4860
static struct serdes_config serdes1_cfg_tbl[] = {
/* SerDes 1 */
+ {0x01, {AURORA, AURORA, CPRI6, CPRI5,
+ CPRI4, CPRI3, CPRI2, CPRI1} },
{0x02, {AURORA, AURORA, CPRI6, CPRI5,
CPRI4, CPRI3, CPRI2, CPRI1} },
{0x04, {AURORA, AURORA, CPRI6, CPRI5,
@@ -26,6 +28,8 @@
CPRI4, CPRI3, CPRI2, CPRI1} },
{0x06, {AURORA, AURORA, CPRI6, CPRI5,
CPRI4, CPRI3, CPRI2, CPRI1} },
+ {0x07, {AURORA, AURORA, CPRI6, CPRI5,
+ CPRI4, CPRI3, CPRI2, CPRI1} },
{0x08, {AURORA, AURORA, CPRI6, CPRI5,
CPRI4, CPRI3, CPRI2, CPRI1} },
{0x09, {AURORA, AURORA, CPRI6, CPRI5,
@@ -184,12 +188,17 @@
CPRI4, CPRI3, NONE, NONE} },
{0x0F, {NONE, NONE, CPRI6, CPRI5,
CPRI4, CPRI3, NONE, NONE} },
+ {0x17, {NONE, NONE,
+ SGMII_FM1_DTSEC3, SGMII_FM1_DTSEC4,
+ NONE, NONE, NONE, NONE} },
{0x18, {NONE, NONE,
SGMII_FM1_DTSEC3, SGMII_FM1_DTSEC4,
NONE, NONE, NONE, NONE} },
{0x1B, {NONE, NONE,
SGMII_FM1_DTSEC3, SGMII_FM1_DTSEC4,
NONE, NONE, NONE, NONE} },
+ {0x1D, {NONE, NONE, AURORA, AURORA,
+ NONE, NONE, NONE, NONE} },
{0x1E, {NONE, NONE, AURORA, AURORA,
NONE, NONE, NONE, NONE} },
{0x21, {NONE, NONE, AURORA, AURORA,
@@ -199,19 +208,29 @@
{}
};
static struct serdes_config serdes2_cfg_tbl[] = {
+ {0x48, {SGMII_FM1_DTSEC1, SGMII_FM1_DTSEC2,
+ SGMII_FM1_DTSEC3, AURORA,
+ NONE, NONE, NONE, NONE} },
{0x49, {SGMII_FM1_DTSEC1, SGMII_FM1_DTSEC2,
SGMII_FM1_DTSEC3, AURORA,
NONE, NONE, NONE, NONE} },
{0x4A, {SGMII_FM1_DTSEC1, SGMII_FM1_DTSEC2,
SGMII_FM1_DTSEC3, AURORA,
NONE, NONE, NONE, NONE} },
+ {0x6E, {SGMII_FM1_DTSEC1, SGMII_FM1_DTSEC2,
+ AURORA, AURORA, NONE, NONE, NONE, NONE} },
{0x6F, {SGMII_FM1_DTSEC1, SGMII_FM1_DTSEC2,
AURORA, AURORA, NONE, NONE, NONE, NONE} },
{0x70, {SGMII_FM1_DTSEC1, SGMII_FM1_DTSEC2,
AURORA, AURORA, NONE, NONE, NONE, NONE} },
+ {0x99, {PCIE1, PCIE1,
+ SGMII_FM1_DTSEC3, SGMII_FM1_DTSEC4,
+ NONE, NONE, NONE, NONE} },
{0x9A, {PCIE1, PCIE1,
SGMII_FM1_DTSEC3, SGMII_FM1_DTSEC4,
NONE, NONE, NONE, NONE} },
+ {0x9D, {PCIE1, PCIE1, PCIE1, PCIE1,
+ NONE, NONE, NONE, NONE} },
{0x9E, {PCIE1, PCIE1, PCIE1, PCIE1,
NONE, NONE, NONE, NONE} },
{}
diff --git a/arch/powerpc/cpu/mpc85xx/cmd_errata.c b/arch/powerpc/cpu/mpc85xx/cmd_errata.c
index fe3eb06..2d5ddf0 100644
--- a/arch/powerpc/cpu/mpc85xx/cmd_errata.c
+++ b/arch/powerpc/cpu/mpc85xx/cmd_errata.c
@@ -271,7 +271,8 @@
puts("Work-around for Erratum USB14 enabled\n");
#endif
#ifdef CONFIG_SYS_FSL_ERRATUM_A007186
- puts("Work-around for Erratum A007186 enabled\n");
+ if (has_erratum_a007186())
+ puts("Work-around for Erratum A007186 enabled\n");
#endif
#ifdef CONFIG_SYS_FSL_ERRATUM_A006593
puts("Work-around for Erratum A006593 enabled\n");
@@ -313,6 +314,14 @@
#ifdef CONFIG_SYS_FSL_ERRATUM_A005434
puts("Work-around for Erratum A-005434 enabled\n");
#endif
+#if defined(CONFIG_SYS_FSL_ERRATUM_A008044) && \
+ defined(CONFIG_A008044_WORKAROUND)
+ if (IS_SVR_REV(svr, 1, 0))
+ puts("Work-around for Erratum A-008044 enabled\n");
+#endif
+#if defined(CONFIG_SYS_FSL_B4860QDS_XFI_ERR) && defined(CONFIG_B4860QDS)
+ puts("Work-around for Erratum XFI on B4860QDS enabled\n");
+#endif
return 0;
}
diff --git a/arch/powerpc/cpu/mpc85xx/fsl_corenet2_serdes.c b/arch/powerpc/cpu/mpc85xx/fsl_corenet2_serdes.c
index 8edf5bb..5cfae47 100644
--- a/arch/powerpc/cpu/mpc85xx/fsl_corenet2_serdes.c
+++ b/arch/powerpc/cpu/mpc85xx/fsl_corenet2_serdes.c
@@ -11,6 +11,7 @@
#include <asm/processor.h>
#include <asm/fsl_law.h>
#include <asm/errno.h>
+#include <asm/fsl_errata.h>
#include "fsl_corenet2_serdes.h"
#ifdef CONFIG_SYS_FSL_SRDS_1
@@ -203,7 +204,7 @@
sel = (sfp_spfr0 >> FUSE_VAL_SHIFT) & FUSE_VAL_MASK;
- if (sel == 0x01 || sel == 0x02) {
+ if (has_erratum_a007186() && (sel == 0x01 || sel == 0x02)) {
for (pll_num = 0; pll_num < SRDS_MAX_BANK; pll_num++) {
pll_status = in_be32(&srds_regs->bank[pll_num].pllcr0);
debug("A007186: pll_num=%x pllcr0=%x\n",
diff --git a/arch/powerpc/cpu/mpc85xx/p2041_ids.c b/arch/powerpc/cpu/mpc85xx/p2041_ids.c
index 488e078..6e3cddd 100644
--- a/arch/powerpc/cpu/mpc85xx/p2041_ids.c
+++ b/arch/powerpc/cpu/mpc85xx/p2041_ids.c
@@ -50,8 +50,8 @@
SET_PCI_LIODN(CONFIG_SYS_FSL_PCIE_COMPAT, 2, 194),
SET_PCI_LIODN(CONFIG_SYS_FSL_PCIE_COMPAT, 3, 195),
- SET_DMA_LIODN(1, 197),
- SET_DMA_LIODN(2, 198),
+ SET_DMA_LIODN(1, "fsl,eloplus-dma", 197),
+ SET_DMA_LIODN(2, "fsl,eloplus-dma", 198),
SET_GUTS_LIODN("fsl,rapidio-delta", 199, rio1liodnr, 0),
SET_GUTS_LIODN(NULL, 200, rio2liodnr, 0),
diff --git a/arch/powerpc/cpu/mpc85xx/p3041_ids.c b/arch/powerpc/cpu/mpc85xx/p3041_ids.c
index 7d98870..2b57703 100644
--- a/arch/powerpc/cpu/mpc85xx/p3041_ids.c
+++ b/arch/powerpc/cpu/mpc85xx/p3041_ids.c
@@ -51,8 +51,8 @@
SET_PCI_LIODN(CONFIG_SYS_FSL_PCIE_COMPAT, 3, 195),
SET_PCI_LIODN(CONFIG_SYS_FSL_PCIE_COMPAT, 4, 196),
- SET_DMA_LIODN(1, 197),
- SET_DMA_LIODN(2, 198),
+ SET_DMA_LIODN(1, "fsl,eloplus-dma", 197),
+ SET_DMA_LIODN(2, "fsl,eloplus-dma", 198),
SET_GUTS_LIODN("fsl,rapidio-delta", 199, rio1liodnr, 0),
SET_GUTS_LIODN(NULL, 200, rio2liodnr, 0),
diff --git a/arch/powerpc/cpu/mpc85xx/p4080_ids.c b/arch/powerpc/cpu/mpc85xx/p4080_ids.c
index b2a23c0..94a5143 100644
--- a/arch/powerpc/cpu/mpc85xx/p4080_ids.c
+++ b/arch/powerpc/cpu/mpc85xx/p4080_ids.c
@@ -40,8 +40,8 @@
SET_PCI_LIODN(CONFIG_SYS_FSL_PCIE_COMPAT, 2, 194),
SET_PCI_LIODN(CONFIG_SYS_FSL_PCIE_COMPAT, 3, 195),
- SET_DMA_LIODN(1, 196),
- SET_DMA_LIODN(2, 197),
+ SET_DMA_LIODN(1, "fsl,eloplus-dma", 196),
+ SET_DMA_LIODN(2, "fsl,eloplus-dma", 197),
SET_GUTS_LIODN("fsl,srio-rmu", 200, rmuliodnr, 0xd3000),
diff --git a/arch/powerpc/cpu/mpc85xx/p5020_ids.c b/arch/powerpc/cpu/mpc85xx/p5020_ids.c
index b5d787c..0f292cf 100644
--- a/arch/powerpc/cpu/mpc85xx/p5020_ids.c
+++ b/arch/powerpc/cpu/mpc85xx/p5020_ids.c
@@ -51,8 +51,8 @@
SET_PCI_LIODN(CONFIG_SYS_FSL_PCIE_COMPAT, 3, 195),
SET_PCI_LIODN(CONFIG_SYS_FSL_PCIE_COMPAT, 4, 196),
- SET_DMA_LIODN(1, 197),
- SET_DMA_LIODN(2, 198),
+ SET_DMA_LIODN(1, "fsl,eloplus-dma", 197),
+ SET_DMA_LIODN(2, "fsl,eloplus-dma", 198),
SET_GUTS_LIODN("fsl,rapidio-delta", 199, rio1liodnr, 0),
SET_GUTS_LIODN(NULL, 200, rio2liodnr, 0),
diff --git a/arch/powerpc/cpu/mpc85xx/p5040_ids.c b/arch/powerpc/cpu/mpc85xx/p5040_ids.c
index 990f179..d4343ef 100644
--- a/arch/powerpc/cpu/mpc85xx/p5040_ids.c
+++ b/arch/powerpc/cpu/mpc85xx/p5040_ids.c
@@ -42,8 +42,8 @@
SET_PCI_LIODN_BASE(CONFIG_SYS_FSL_PCIE_COMPAT, 2, 196),
SET_PCI_LIODN_BASE(CONFIG_SYS_FSL_PCIE_COMPAT, 3, 197),
- SET_DMA_LIODN(1, 193),
- SET_DMA_LIODN(2, 194),
+ SET_DMA_LIODN(1, "fsl,eloplus-dma", 193),
+ SET_DMA_LIODN(2, "fsl,eloplus-dma", 194),
};
int liodn_tbl_sz = ARRAY_SIZE(liodn_tbl);
diff --git a/arch/powerpc/cpu/mpc85xx/speed.c b/arch/powerpc/cpu/mpc85xx/speed.c
index 8426b1a..7e69873 100644
--- a/arch/powerpc/cpu/mpc85xx/speed.c
+++ b/arch/powerpc/cpu/mpc85xx/speed.c
@@ -37,6 +37,7 @@
#ifdef CONFIG_SYS_FSL_QORIQ_CHASSIS2
int cc_group[12] = CONFIG_SYS_FSL_CLUSTER_CLOCKS;
#endif
+ __maybe_unused u32 svr;
const u8 core_cplx_PLL[16] = {
[ 0] = 0, /* CC1 PPL / 1 */
@@ -122,11 +123,27 @@
/* T4240/T4160 Rev2.0 MEM_PLL_RAT uses a value which is half of
* T4240/T4160 Rev1.0. eg. It's 12 in Rev1.0, however, for Rev2.0
* it uses 6.
+ * T2080 rev 1.1 and later also use half mem_pll comparing with rev 1.0
*/
#if defined(CONFIG_PPC_T4240) || defined(CONFIG_PPC_T4160) || \
- defined(CONFIG_PPC_T4080)
- if (SVR_MAJ(get_svr()) >= 2)
- mem_pll_rat *= 2;
+ defined(CONFIG_PPC_T4080) || defined(CONFIG_PPC_T2080)
+ svr = get_svr();
+ switch (SVR_SOC_VER(svr)) {
+ case SVR_T4240:
+ case SVR_T4160:
+ case SVR_T4120:
+ case SVR_T4080:
+ if (SVR_MAJ(svr) >= 2)
+ mem_pll_rat *= 2;
+ break;
+ case SVR_T2080:
+ case SVR_T2081:
+ if ((SVR_MAJ(svr) > 1) || (SVR_MIN(svr) >= 1))
+ mem_pll_rat *= 2;
+ break;
+ default:
+ break;
+ }
#endif
if (mem_pll_rat > 2)
sys_info->freq_ddrbus *= mem_pll_rat;
@@ -168,6 +185,9 @@
defined(CONFIG_PPC_T2080) || defined(CONFIG_PPC_T2081)
#define FM1_CLK_SEL 0xe0000000
#define FM1_CLK_SHIFT 29
+#elif defined(CONFIG_PPC_T1024) || defined(CONFIG_PPC_T1023)
+#define FM1_CLK_SEL 0x00000007
+#define FM1_CLK_SHIFT 0
#else
#define PME_CLK_SEL 0xe0000000
#define PME_CLK_SHIFT 29
@@ -175,8 +195,12 @@
#define FM1_CLK_SHIFT 26
#endif
#if !defined(CONFIG_FM_PLAT_CLK_DIV) || !defined(CONFIG_PME_PLAT_CLK_DIV)
+#if defined(CONFIG_PPC_T1024) || defined(CONFIG_PPC_T1023)
+ rcw_tmp = in_be32(&gur->rcwsr[15]) - 4;
+#else
rcw_tmp = in_be32(&gur->rcwsr[7]);
#endif
+#endif
#ifdef CONFIG_SYS_DPAA_PME
#ifndef CONFIG_PME_PLAT_CLK_DIV
@@ -213,7 +237,10 @@
#endif
#ifdef CONFIG_SYS_DPAA_QBMAN
- sys_info->freq_qman = sys_info->freq_systembus / 2;
+#ifndef CONFIG_QBMAN_CLK_DIV
+#define CONFIG_QBMAN_CLK_DIV 2
+#endif
+ sys_info->freq_qman = sys_info->freq_systembus / CONFIG_QBMAN_CLK_DIV;
#endif
#ifdef CONFIG_SYS_DPAA_FMAN
diff --git a/arch/powerpc/cpu/mpc85xx/t1024_ids.c b/arch/powerpc/cpu/mpc85xx/t1024_ids.c
new file mode 100644
index 0000000..132689b
--- /dev/null
+++ b/arch/powerpc/cpu/mpc85xx/t1024_ids.c
@@ -0,0 +1,82 @@
+/*
+ * Copyright 2014 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <asm/fsl_portals.h>
+#include <asm/fsl_liodn.h>
+
+#ifdef CONFIG_SYS_DPAA_QBMAN
+struct qportal_info qp_info[CONFIG_SYS_QMAN_NUM_PORTALS] = {
+ /* dqrr liodn, frame data liodn, liodn off, sdest */
+ SET_QP_INFO(1, 27, 1, 0),
+ SET_QP_INFO(2, 28, 1, 0),
+ SET_QP_INFO(3, 29, 1, 1),
+ SET_QP_INFO(4, 30, 1, 1),
+ SET_QP_INFO(5, 31, 1, 2),
+ SET_QP_INFO(6, 32, 1, 2),
+ SET_QP_INFO(7, 33, 1, 3),
+ SET_QP_INFO(8, 34, 1, 3),
+ SET_QP_INFO(9, 35, 1, 0),
+ SET_QP_INFO(10, 36, 1, 0),
+};
+#endif
+
+struct liodn_id_table liodn_tbl[] = {
+#ifdef CONFIG_SYS_DPAA_QBMAN
+ SET_QMAN_LIODN(62),
+ SET_BMAN_LIODN(63),
+#endif
+
+ SET_SDHC_LIODN(1, 552),
+
+ SET_USB_LIODN(1, "fsl-usb2-mph", 553),
+ SET_USB_LIODN(2, "fsl-usb2-dr", 554),
+
+ SET_SATA_LIODN(1, 555),
+
+ SET_PCI_LIODN_BASE(CONFIG_SYS_FSL_PCIE_COMPAT, 1, 148),
+ SET_PCI_LIODN_BASE(CONFIG_SYS_FSL_PCIE_COMPAT, 2, 228),
+ SET_PCI_LIODN_BASE(CONFIG_SYS_FSL_PCIE_COMPAT, 3, 308),
+
+ SET_DMA_LIODN(1, "fsl,elo3-dma", 147),
+ SET_DMA_LIODN(2, "fsl,elo3-dma", 227),
+ /* SET_NEXUS_LIODN(557), -- not yet implemented */
+ SET_QE_LIODN(559),
+ SET_TDM_LIODN(560),
+};
+int liodn_tbl_sz = ARRAY_SIZE(liodn_tbl);
+
+#ifdef CONFIG_SYS_DPAA_FMAN
+struct liodn_id_table fman1_liodn_tbl[] = {
+ SET_FMAN_RX_1G_LIODN(1, 0, 88),
+ SET_FMAN_RX_1G_LIODN(1, 1, 89),
+ SET_FMAN_RX_1G_LIODN(1, 2, 90),
+ SET_FMAN_RX_1G_LIODN(1, 3, 91),
+ SET_FMAN_RX_10G_LIODN(1, 0, 94),
+};
+int fman1_liodn_tbl_sz = ARRAY_SIZE(fman1_liodn_tbl);
+#endif
+
+struct liodn_id_table sec_liodn_tbl[] = {
+ SET_SEC_JR_LIODN_ENTRY(0, 454, 458),
+ SET_SEC_JR_LIODN_ENTRY(1, 455, 459),
+ SET_SEC_JR_LIODN_ENTRY(2, 456, 460),
+ SET_SEC_JR_LIODN_ENTRY(3, 457, 461),
+ SET_SEC_RTIC_LIODN_ENTRY(a, 453),
+ SET_SEC_RTIC_LIODN_ENTRY(b, 549),
+ SET_SEC_RTIC_LIODN_ENTRY(c, 550),
+ SET_SEC_RTIC_LIODN_ENTRY(d, 551),
+ SET_SEC_DECO_LIODN_ENTRY(0, 541, 610),
+ SET_SEC_DECO_LIODN_ENTRY(1, 542, 611),
+};
+int sec_liodn_tbl_sz = ARRAY_SIZE(sec_liodn_tbl);
+
+struct liodn_id_table liodn_bases[] = {
+ [FSL_HW_PORTAL_SEC] = SET_LIODN_BASE_2(462, 558),
+#ifdef CONFIG_SYS_DPAA_FMAN
+ [FSL_HW_PORTAL_FMAN1] = SET_LIODN_BASE_1(973),
+#endif
+};
diff --git a/arch/powerpc/cpu/mpc85xx/t1024_serdes.c b/arch/powerpc/cpu/mpc85xx/t1024_serdes.c
new file mode 100644
index 0000000..7dc8385
--- /dev/null
+++ b/arch/powerpc/cpu/mpc85xx/t1024_serdes.c
@@ -0,0 +1,52 @@
+/*
+ * Copyright 2014 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <asm/fsl_serdes.h>
+#include <asm/processor.h>
+#include <asm/io.h>
+
+
+static u8 serdes_cfg_tbl[][4] = {
+ [0xD5] = {QSGMII_FM1_A, PCIE3, PCIE2, PCIE1},
+ [0xD6] = {QSGMII_FM1_A, PCIE3, PCIE2, SATA1},
+ [0x95] = {XFI_FM1_MAC1, PCIE3, PCIE2, PCIE1},
+ [0x99] = {XFI_FM1_MAC1, PCIE3, SGMII_FM1_DTSEC2, PCIE1},
+ [0x46] = {PCIE1, PCIE1, PCIE2, SATA1},
+ [0x47] = {PCIE1, PCIE1, PCIE2, SGMII_FM1_DTSEC1},
+ [0x56] = {PCIE1, PCIE3, PCIE2, SATA1},
+ [0x5A] = {PCIE1, PCIE3, SGMII_FM1_DTSEC2, SATA1},
+ [0x5B] = {PCIE1, PCIE3, SGMII_FM1_DTSEC2, SGMII_FM1_DTSEC1},
+ [0x6A] = {PCIE1, SGMII_FM1_DTSEC3, SGMII_FM1_DTSEC2, SATA1},
+ [0x6B] = {PCIE1, SGMII_FM1_DTSEC3, SGMII_FM1_DTSEC2, SGMII_FM1_DTSEC1},
+ [0x6F] = {PCIE1, SGMII_FM1_DTSEC3, SGMII_2500_FM1_DTSEC2,
+ SGMII_2500_FM1_DTSEC1},
+ [0x77] = {PCIE1, SGMII_2500_FM1_DTSEC3, PCIE2, SGMII_FM1_DTSEC1},
+ [0x7F] = {PCIE1, SGMII_2500_FM1_DTSEC3, SGMII_2500_FM1_DTSEC2,
+ SGMII_2500_FM1_DTSEC1},
+ [0x119] = {AURORA, PCIE3, SGMII_FM1_DTSEC2, PCIE1},
+ [0x135] = {AURORA, SGMII_2500_FM1_DTSEC3, PCIE2, PCIE1},
+};
+
+enum srds_prtcl serdes_get_prtcl(int serdes, int cfg, int lane)
+{
+ return serdes_cfg_tbl[cfg][lane];
+}
+
+int is_serdes_prtcl_valid(int serdes, u32 prtcl)
+{
+ int i;
+
+ if (prtcl >= ARRAY_SIZE(serdes_cfg_tbl))
+ return 0;
+
+ for (i = 0; i < 4; i++) {
+ if (serdes_cfg_tbl[prtcl][i] != NONE)
+ return 1;
+ }
+
+ return 0;
+}
diff --git a/arch/powerpc/cpu/mpc85xx/t1040_ids.c b/arch/powerpc/cpu/mpc85xx/t1040_ids.c
index a5dfb81..8091722 100644
--- a/arch/powerpc/cpu/mpc85xx/t1040_ids.c
+++ b/arch/powerpc/cpu/mpc85xx/t1040_ids.c
@@ -24,12 +24,6 @@
};
#endif
-struct srio_liodn_id_table srio_liodn_tbl[] = {
- SET_SRIO_LIODN_1(1, 307),
- SET_SRIO_LIODN_1(2, 387),
-};
-int srio_liodn_tbl_sz = ARRAY_SIZE(srio_liodn_tbl);
-
struct liodn_id_table liodn_tbl[] = {
#ifdef CONFIG_SYS_DPAA_QBMAN
SET_QMAN_LIODN(62),
@@ -38,12 +32,21 @@
SET_SDHC_LIODN(1, 552),
+ SET_PME_LIODN(117),
+
SET_USB_LIODN(1, "fsl-usb2-mph", 553),
+ SET_USB_LIODN(2, "fsl-usb2-dr", 554),
- SET_PCI_LIODN("fsl,qoriq-pcie-v2.2", 1, 148),
+ SET_SATA_LIODN(1, 555),
+ SET_SATA_LIODN(2, 556),
- SET_DMA_LIODN(1, 147),
- SET_DMA_LIODN(2, 227),
+ SET_PCI_LIODN_BASE(CONFIG_SYS_FSL_PCIE_COMPAT, 1, 148),
+ SET_PCI_LIODN_BASE(CONFIG_SYS_FSL_PCIE_COMPAT, 2, 228),
+ SET_PCI_LIODN_BASE(CONFIG_SYS_FSL_PCIE_COMPAT, 3, 308),
+ SET_PCI_LIODN_BASE(CONFIG_SYS_FSL_PCIE_COMPAT, 4, 388),
+
+ SET_DMA_LIODN(1, "fsl,elo3-dma", 147),
+ SET_DMA_LIODN(2, "fsl,elo3-dma", 227),
/* SET_NEXUS_LIODN(557), -- not yet implemented */
SET_QE_LIODN(559),
@@ -74,6 +77,12 @@
SET_SEC_RTIC_LIODN_ENTRY(d, 551),
SET_SEC_DECO_LIODN_ENTRY(0, 541, 610),
SET_SEC_DECO_LIODN_ENTRY(1, 542, 611),
+ SET_SEC_DECO_LIODN_ENTRY(2, 543, 612),
+ SET_SEC_DECO_LIODN_ENTRY(3, 544, 613),
+ SET_SEC_DECO_LIODN_ENTRY(4, 545, 614),
+ SET_SEC_DECO_LIODN_ENTRY(5, 546, 615),
+ SET_SEC_DECO_LIODN_ENTRY(6, 547, 616),
+ SET_SEC_DECO_LIODN_ENTRY(7, 548, 617),
};
int sec_liodn_tbl_sz = ARRAY_SIZE(sec_liodn_tbl);
@@ -82,4 +91,7 @@
#ifdef CONFIG_SYS_DPAA_FMAN
[FSL_HW_PORTAL_FMAN1] = SET_LIODN_BASE_1(973),
#endif
+#ifdef CONFIG_SYS_DPAA_PME
+ [FSL_HW_PORTAL_PME] = SET_LIODN_BASE_2(770, 846),
+#endif
};
diff --git a/arch/powerpc/cpu/mpc85xx/t2080_ids.c b/arch/powerpc/cpu/mpc85xx/t2080_ids.c
index 0bfd447..eda7f59 100644
--- a/arch/powerpc/cpu/mpc85xx/t2080_ids.c
+++ b/arch/powerpc/cpu/mpc85xx/t2080_ids.c
@@ -63,9 +63,9 @@
SET_PCI_LIODN_BASE(CONFIG_SYS_FSL_PCIE_COMPAT, 3, 308),
SET_PCI_LIODN_BASE(CONFIG_SYS_FSL_PCIE_COMPAT, 4, 388),
- SET_DMA_LIODN(1, 147),
- SET_DMA_LIODN(2, 227),
- SET_DMA_LIODN(3, 226),
+ SET_DMA_LIODN(1, "fsl,elo3-dma", 147),
+ SET_DMA_LIODN(2, "fsl,elo3-dma", 227),
+ SET_DMA_LIODN(3, "fsl,elo3-dma", 226),
SET_GUTS_LIODN("fsl,rapidio-delta", 199, rio1liodnr, 0),
SET_GUTS_LIODN(NULL, 200, rio2liodnr, 0),
diff --git a/arch/powerpc/cpu/mpc85xx/t2080_serdes.c b/arch/powerpc/cpu/mpc85xx/t2080_serdes.c
index 7138bb4..c65f41d 100644
--- a/arch/powerpc/cpu/mpc85xx/t2080_serdes.c
+++ b/arch/powerpc/cpu/mpc85xx/t2080_serdes.c
@@ -169,6 +169,7 @@
{0x01, {PCIE1, PCIE1, PCIE1, PCIE1, PCIE1, PCIE1, PCIE1, PCIE1} },
{0x29, {SRIO2, SRIO2, SRIO2, SRIO2, SRIO1, SRIO1, SRIO1, SRIO1} },
{0x2D, {SRIO2, SRIO2, SRIO2, SRIO2, SRIO1, SRIO1, SRIO1, SRIO1} },
+ {0x2E, {SRIO2, SRIO2, SRIO2, SRIO2, SRIO1, SRIO1, SRIO1, SRIO1} },
{0x15, {PCIE1, PCIE1, PCIE1, PCIE1, PCIE2, PCIE2, SATA1, SATA2} },
{0x27, {PCIE1, PCIE1, PCIE1, PCIE1, NONE, NONE, SATA1, SATA2} },
{0x18, {PCIE1, PCIE1, PCIE1, PCIE1, AURORA, AURORA, SATA1, SATA2} },
diff --git a/arch/powerpc/cpu/mpc85xx/t4240_ids.c b/arch/powerpc/cpu/mpc85xx/t4240_ids.c
index 1a3cb33..470b080 100644
--- a/arch/powerpc/cpu/mpc85xx/t4240_ids.c
+++ b/arch/powerpc/cpu/mpc85xx/t4240_ids.c
@@ -93,8 +93,8 @@
SET_PCI_LIODN_BASE(CONFIG_SYS_FSL_PCIE_COMPAT, 3, 308),
SET_PCI_LIODN_BASE(CONFIG_SYS_FSL_PCIE_COMPAT, 4, 388),
- SET_DMA_LIODN(1, 147),
- SET_DMA_LIODN(2, 227),
+ SET_DMA_LIODN(1, "fsl,elo3-dma", 147),
+ SET_DMA_LIODN(2, "fsl,elo3-dma", 227),
SET_GUTS_LIODN("fsl,rapidio-delta", 199, rio1liodnr, 0),
SET_GUTS_LIODN(NULL, 200, rio2liodnr, 0),
diff --git a/arch/powerpc/cpu/mpc8xxx/cpu.c b/arch/powerpc/cpu/mpc8xxx/cpu.c
index 84fec5e..2d28eb2 100644
--- a/arch/powerpc/cpu/mpc8xxx/cpu.c
+++ b/arch/powerpc/cpu/mpc8xxx/cpu.c
@@ -76,6 +76,10 @@
CPU_TYPE_ENTRY(T1020, T1020, 0),
CPU_TYPE_ENTRY(T1021, T1021, 0),
CPU_TYPE_ENTRY(T1022, T1022, 0),
+ CPU_TYPE_ENTRY(T1024, T1024, 0),
+ CPU_TYPE_ENTRY(T1023, T1023, 0),
+ CPU_TYPE_ENTRY(T1014, T1014, 0),
+ CPU_TYPE_ENTRY(T1013, T1013, 0),
CPU_TYPE_ENTRY(T2080, T2080, 0),
CPU_TYPE_ENTRY(T2081, T2081, 0),
CPU_TYPE_ENTRY(BSC9130, 9130, 1),
diff --git a/arch/powerpc/include/asm/config_mpc85xx.h b/arch/powerpc/include/asm/config_mpc85xx.h
index 7860b40..01b0905 100644
--- a/arch/powerpc/include/asm/config_mpc85xx.h
+++ b/arch/powerpc/include/asm/config_mpc85xx.h
@@ -769,6 +769,7 @@
#define CONFIG_SYS_PME_CLK CONFIG_PME_PLAT_CLK_DIV
#define CONFIG_SYS_FSL_DDR_VER FSL_DDR_VER_5_0
#define CONFIG_SYS_FSL_IFC_BANK_COUNT 8
+#define CONFIG_SYS_FSL_ERRATUM_A008044
#define CONFIG_SYS_FMAN_V3
#define CONFIG_FM_PLAT_CLK_DIV 1
#define CONFIG_SYS_FM1_CLK CONFIG_FM_PLAT_CLK_DIV
@@ -786,6 +787,52 @@
#define MAX_QE_RISC 1
#define QE_NUM_OF_SNUM 28
+#elif defined(CONFIG_PPC_T1024) || defined(CONFIG_PPC_T1023) ||\
+defined(CONFIG_PPC_T1014) || defined(CONFIG_PPC_T1013)
+#define CONFIG_E5500
+#define CONFIG_FSL_CORENET /* Freescale CoreNet platform */
+#define CONFIG_SYS_FSL_QORIQ_CHASSIS2 /* Freescale Chassis generation 2 */
+#define CONFIG_SYS_FSL_CORES_PER_CLUSTER 1
+#define CONFIG_SYS_FSL_QMAN_V3 /* QMAN version 3 */
+#define CONFIG_SYS_FMAN_V3
+#ifdef CONFIG_SYS_FSL_DDR4
+#define CONFIG_SYS_FSL_DDRC_GEN4
+#endif
+#if defined(CONFIG_PPC_T1024) || defined(CONFIG_PPC_T1023)
+#define CONFIG_MAX_CPUS 2
+#elif defined(CONFIG_PPC_T1014) || defined(CONFIG_PPC_T1013)
+#define CONFIG_MAX_CPUS 1
+#endif
+#define CONFIG_SYS_FSL_NUM_CC_PLL 2
+#define CONFIG_SYS_FSL_CLUSTER_CLOCKS { 1, 1, 1, 1 }
+#define CONFIG_SYS_SDHC_CLOCK 0
+#define CONFIG_SYS_FSL_NUM_LAWS 16
+#define CONFIG_SYS_FSL_SRDS_1
+#define CONFIG_SYS_FSL_SEC_COMPAT 5
+#define CONFIG_SYS_NUM_FMAN 1
+#define CONFIG_SYS_NUM_FM1_DTSEC 4
+#define CONFIG_SYS_NUM_FM1_10GEC 1
+#define CONFIG_FSL_FM_10GEC_REGULAR_NOTATION
+#define CONFIG_NUM_DDR_CONTROLLERS 1
+#define CONFIG_USB_MAX_CONTROLLER_COUNT 2
+#define CONFIG_SYS_FSL_DDR_VER FSL_DDR_VER_5_0
+#define CONFIG_SYS_FSL_IFC_BANK_COUNT 8
+#define CONFIG_SYS_FM1_CLK 0
+#define CONFIG_QBMAN_CLK_DIV 1
+#define CONFIG_SYS_FM_MURAM_SIZE 0x30000
+#define CONFIG_SYS_FSL_SINGLE_SOURCE_CLK
+#define CONFIG_SYS_FSL_TBCLK_DIV 16
+#define CONFIG_SYS_FSL_PCIE_COMPAT "fsl,qoriq-pcie-v2.4"
+#define CONFIG_SYS_FSL_USB_DUAL_PHY_ENABLE
+#define CONFIG_SYS_FSL_USB_INTERNAL_UTMI_PHY
+#define CONFIG_SYS_CCSRBAR_DEFAULT 0xfe000000
+#define CONFIG_SYS_FSL_ERRATUM_ESDHC111
+#define ESDHCI_QUIRK_BROKEN_TIMEOUT_VALUE
+#define QE_MURAM_SIZE 0x6000UL
+#define MAX_QE_RISC 1
+#define QE_NUM_OF_SNUM 28
+#define CONFIG_SYS_FSL_SFP_VER_3_0
+
#elif defined(CONFIG_PPC_T2080) || defined(CONFIG_PPC_T2081)
#define CONFIG_E6500
#define CONFIG_SYS_PPC64 /* 64-bit core */
diff --git a/arch/powerpc/include/asm/fsl_errata.h b/arch/powerpc/include/asm/fsl_errata.h
index b9e2fb0..61c6d70 100644
--- a/arch/powerpc/include/asm/fsl_errata.h
+++ b/arch/powerpc/include/asm/fsl_errata.h
@@ -27,3 +27,27 @@
}
#endif
#endif
+
+#ifdef CONFIG_SYS_FSL_ERRATUM_A007186
+static inline bool has_erratum_a007186(void)
+{
+ u32 svr = get_svr();
+ u32 soc = SVR_SOC_VER(svr);
+
+ switch (soc) {
+ case SVR_T4240:
+ return IS_SVR_REV(svr, 2, 0);
+ case SVR_T4160:
+ return IS_SVR_REV(svr, 2, 0);
+ case SVR_B4860:
+ return IS_SVR_REV(svr, 2, 0);
+ case SVR_B4420:
+ return IS_SVR_REV(svr, 2, 0);
+ case SVR_T2081:
+ case SVR_T2080:
+ return IS_SVR_REV(svr, 1, 0);
+ }
+
+ return false;
+}
+#endif
diff --git a/arch/powerpc/include/asm/fsl_liodn.h b/arch/powerpc/include/asm/fsl_liodn.h
index adfbb66..811f034 100644
--- a/arch/powerpc/include/asm/fsl_liodn.h
+++ b/arch/powerpc/include/asm/fsl_liodn.h
@@ -91,8 +91,8 @@
CONFIG_SYS_MPC85xx_PCIE##pciNum##_OFFSET)
/* reg nodes for DMA start @ 0x300 */
-#define SET_DMA_LIODN(dmaNum, liodn) \
- SET_GUTS_LIODN("fsl,eloplus-dma", liodn, dma##dmaNum##liodnr,\
+#define SET_DMA_LIODN(dmaNum, compat, liodn) \
+ SET_GUTS_LIODN(compat, liodn, dma##dmaNum##liodnr,\
CONFIG_SYS_MPC85xx_DMA##dmaNum##_OFFSET + 0x300)
#define SET_SDHC_LIODN(sdhcNum, liodn) \
diff --git a/arch/powerpc/include/asm/fsl_secure_boot.h b/arch/powerpc/include/asm/fsl_secure_boot.h
index 74c5d8f..14c6fc3 100644
--- a/arch/powerpc/include/asm/fsl_secure_boot.h
+++ b/arch/powerpc/include/asm/fsl_secure_boot.h
@@ -22,7 +22,9 @@
defined(CONFIG_T2080QDS) || \
defined(CONFIG_T2080RDB) || \
defined(CONFIG_T1040QDS) || \
- defined(CONFIG_T104xRDB)
+ defined(CONFIG_T104xRDB) || \
+ defined(CONFIG_PPC_T1023) || \
+ defined(CONFIG_PPC_T1024)
#define CONFIG_SYS_CPC_REINIT_F
#undef CONFIG_SYS_INIT_L3_ADDR
#define CONFIG_SYS_INIT_L3_ADDR 0xbff00000
diff --git a/arch/powerpc/include/asm/immap_85xx.h b/arch/powerpc/include/asm/immap_85xx.h
index 0264523..ace1d12 100644
--- a/arch/powerpc/include/asm/immap_85xx.h
+++ b/arch/powerpc/include/asm/immap_85xx.h
@@ -1626,10 +1626,15 @@
#define FSL_CORENET_DEVDISR2_DTSEC1_6 0x04000000
#define FSL_CORENET_DEVDISR2_DTSEC1_9 0x00800000
#define FSL_CORENET_DEVDISR2_DTSEC1_10 0x00400000
+#ifdef CONFIG_FSL_FM_10GEC_REGULAR_NOTATION
+#define FSL_CORENET_DEVDISR2_10GEC1_1 0x80000000
+#define FSL_CORENET_DEVDISR2_10GEC1_2 0x40000000
+#else
#define FSL_CORENET_DEVDISR2_10GEC1_1 0x00800000
#define FSL_CORENET_DEVDISR2_10GEC1_2 0x00400000
#define FSL_CORENET_DEVDISR2_10GEC1_3 0x80000000
#define FSL_CORENET_DEVDISR2_10GEC1_4 0x40000000
+#endif
#define FSL_CORENET_DEVDISR2_DTSEC2_1 0x00080000
#define FSL_CORENET_DEVDISR2_DTSEC2_2 0x00040000
#define FSL_CORENET_DEVDISR2_DTSEC2_3 0x00020000
@@ -1787,6 +1792,21 @@
#define PXCKEN_MASK 0x80000000
#define PXCK_MASK 0x00FF0000
#define PXCK_BITS_START 16
+#elif defined(CONFIG_PPC_T1024) || defined(CONFIG_PPC_T1023) || \
+ defined(CONFIG_PPC_T1014) || defined(CONFIG_PPC_T1013)
+#define FSL_CORENET2_RCWSR4_SRDS1_PRTCL 0xff800000
+#define FSL_CORENET2_RCWSR4_SRDS1_PRTCL_SHIFT 23
+#define FSL_CORENET_RCWSR6_BOOT_LOC 0x0f800000
+#define FSL_CORENET_RCWSR13_EC1 0x30000000 /* bits 418..419 */
+#define FSL_CORENET_RCWSR13_EC1_RGMII 0x00000000
+#define FSL_CORENET_RCWSR13_EC1_GPIO 0x10000000
+#define FSL_CORENET_RCWSR13_EC2 0x0c000000
+#define FSL_CORENET_RCWSR13_EC2_RGMII 0x08000000
+#define CONFIG_SYS_FSL_SCFG_PIXCLKCR_OFFSET 0x28
+#define CONFIG_SYS_FSL_SCFG_IODSECR1_OFFSET 0xd00
+#define PXCKEN_MASK 0x80000000
+#define PXCK_MASK 0x00FF0000
+#define PXCK_BITS_START 16
#elif defined(CONFIG_PPC_T2080) || defined(CONFIG_PPC_T2081)
#define FSL_CORENET2_RCWSR4_SRDS1_PRTCL 0xff000000
#define FSL_CORENET2_RCWSR4_SRDS1_PRTCL_SHIFT 24
@@ -2971,6 +2991,8 @@
(CONFIG_SYS_CCSRBAR + CONFIG_SYS_FSL_SCFG_OFFSET)
#define CONFIG_SYS_FSL_SCFG_PIXCLK_ADDR \
(CONFIG_SYS_FSL_SCFG_ADDR + CONFIG_SYS_FSL_SCFG_PIXCLKCR_OFFSET)
+#define CONFIG_SYS_FSL_SCFG_IODSECR1_ADDR \
+ (CONFIG_SYS_FSL_SCFG_ADDR + CONFIG_SYS_FSL_SCFG_IODSECR1_OFFSET)
#define CONFIG_SYS_FSL_QMAN_ADDR \
(CONFIG_SYS_IMMR + CONFIG_SYS_FSL_QMAN_OFFSET)
#define CONFIG_SYS_FSL_BMAN_ADDR \
diff --git a/arch/powerpc/include/asm/processor.h b/arch/powerpc/include/asm/processor.h
index 1b98e0f..2ed51b1 100644
--- a/arch/powerpc/include/asm/processor.h
+++ b/arch/powerpc/include/asm/processor.h
@@ -1133,6 +1133,10 @@
#define SVR_T1020 0x852100
#define SVR_T1021 0x852101
#define SVR_T1022 0x852102
+#define SVR_T1024 0x854000
+#define SVR_T1023 0x854100
+#define SVR_T1014 0x854400
+#define SVR_T1013 0x854500
#define SVR_T2080 0x853000
#define SVR_T2081 0x853100
diff --git a/board/freescale/b4860qds/b4860qds.c b/board/freescale/b4860qds/b4860qds.c
index bed8f56..6a8fca6 100644
--- a/board/freescale/b4860qds/b4860qds.c
+++ b/board/freescale/b4860qds/b4860qds.c
@@ -19,6 +19,7 @@
#include <asm/fsl_portals.h>
#include <asm/fsl_liodn.h>
#include <fm_eth.h>
+#include <hwconfig.h>
#include "../common/qixis.h"
#include "../common/vsc3316_3308.h"
@@ -333,6 +334,8 @@
unsigned int num_vsc16_con, num_vsc08_con;
u32 serdes1_prtcl, serdes2_prtcl;
int ret;
+ char buffer[HWCONFIG_BUFFER_SIZE];
+ char *buf = NULL;
serdes1_prtcl = in_be32(&gur->rcwsr[4]) &
FSL_CORENET2_RCWSR4_SRDS1_PRTCL;
@@ -385,15 +388,18 @@
}
break;
+ case 0x01:
case 0x02:
case 0x04:
case 0x05:
case 0x06:
+ case 0x07:
case 0x08:
case 0x09:
case 0x0A:
case 0x0B:
case 0x0C:
+ case 0x2F:
case 0x30:
case 0x32:
case 0x33:
@@ -487,6 +493,9 @@
return -1;
}
+ num_vsc08_con = NUM_CON_VSC3308;
+ /* Configure VSC3308 crossbar switch */
+ ret = select_i2c_ch_pca(I2C_CH_VSC3308);
switch (serdes2_prtcl) {
#ifdef CONFIG_PPC_B4420
case 0x9d:
@@ -494,14 +503,11 @@
case 0x9E:
case 0x9A:
case 0x98:
- case 0xb2:
+ case 0x48:
case 0x49:
case 0x4E:
- case 0x8D:
+ case 0x79:
case 0x7A:
- num_vsc08_con = NUM_CON_VSC3308;
- /* Configure VSC3308 crossbar switch */
- ret = select_i2c_ch_pca(I2C_CH_VSC3308);
if (!ret) {
ret = vsc3308_config(VSC3308_TX_ADDRESS,
vsc08_tx_amc, num_vsc08_con);
@@ -515,6 +521,71 @@
return ret;
}
break;
+ case 0x80:
+ case 0x81:
+ case 0x82:
+ case 0x83:
+ case 0x84:
+ case 0x85:
+ case 0x86:
+ case 0x87:
+ case 0x88:
+ case 0x89:
+ case 0x8a:
+ case 0x8b:
+ case 0x8c:
+ case 0x8d:
+ case 0x8e:
+ case 0xb1:
+ case 0xb2:
+ if (!ret) {
+ /*
+ * Extract hwconfig from environment since environment
+ * is not setup properly yet
+ */
+ getenv_f("hwconfig", buffer, sizeof(buffer));
+ buf = buffer;
+
+ if (hwconfig_subarg_cmp_f("fsl_b4860_serdes2",
+ "sfp_amc", "sfp", buf)) {
+#ifdef CONFIG_SYS_FSL_B4860QDS_XFI_ERR
+ /* change default VSC3308 for XFI erratum */
+ ret = vsc3308_config_adjust(VSC3308_TX_ADDRESS,
+ vsc08_tx_sfp, num_vsc08_con);
+ if (ret)
+ return ret;
+
+ ret = vsc3308_config_adjust(VSC3308_RX_ADDRESS,
+ vsc08_rx_sfp, num_vsc08_con);
+ if (ret)
+ return ret;
+#else
+ ret = vsc3308_config(VSC3308_TX_ADDRESS,
+ vsc08_tx_sfp, num_vsc08_con);
+ if (ret)
+ return ret;
+
+ ret = vsc3308_config(VSC3308_RX_ADDRESS,
+ vsc08_rx_sfp, num_vsc08_con);
+ if (ret)
+ return ret;
+#endif
+ } else {
+ ret = vsc3308_config(VSC3308_TX_ADDRESS,
+ vsc08_tx_amc, num_vsc08_con);
+ if (ret)
+ return ret;
+
+ ret = vsc3308_config(VSC3308_RX_ADDRESS,
+ vsc08_rx_amc, num_vsc08_con);
+ if (ret)
+ return ret;
+ }
+
+ } else {
+ return ret;
+ }
+ break;
default:
printf("WARNING:VSC crossbars programming not supported for: %x"
" SerDes2 Protocol.\n", serdes2_prtcl);
@@ -730,19 +801,23 @@
* to 122.88MHz
*/
switch (serdes1_prtcl) {
+ case 0x29:
case 0x2A:
case 0x2C:
case 0x2D:
case 0x2E:
+ case 0x01:
case 0x02:
case 0x04:
case 0x05:
case 0x06:
+ case 0x07:
case 0x08:
case 0x09:
case 0x0A:
case 0x0B:
case 0x0C:
+ case 0x2F:
case 0x30:
case 0x32:
case 0x33:
@@ -860,6 +935,8 @@
#endif
case 0x9E:
case 0x9A:
+ /* fallthrough */
+ case 0xb1:
case 0xb2:
debug("Configuring IDT for PCIe SATA for srds_prctl:%x\n",
serdes2_prtcl);
@@ -915,6 +992,14 @@
const unsigned int flashbase = CONFIG_SYS_FLASH_BASE;
int flash_esel = find_tlb_idx((void *)flashbase, 1);
int ret;
+ u32 svr = SVR_SOC_VER(get_svr());
+
+ /* Create law for MAPLE only for personalities having MAPLE */
+ if ((svr == SVR_B4860) || (svr == SVR_B4440) ||
+ (svr == SVR_B4420) || (svr == SVR_B4220)) {
+ set_next_law(CONFIG_SYS_MAPLE_MEM_PHYS, LAW_SIZE_16M,
+ LAW_TRGT_IF_MAPLE);
+ }
/*
* Remap Boot flash + PROMJET region to caching-inhibited
diff --git a/board/freescale/b4860qds/eth_b4860qds.c b/board/freescale/b4860qds/eth_b4860qds.c
index 12df9a8..501d4b3 100644
--- a/board/freescale/b4860qds/eth_b4860qds.c
+++ b/board/freescale/b4860qds/eth_b4860qds.c
@@ -112,7 +112,10 @@
* Lanes: A,B,C,D: PCI
* Lanes: E,F,G,H: XAUI2
*/
+ case 0xb1:
case 0xb2:
+ case 0x8c:
+ case 0x8d:
/*
* Configuration:
* SERDES: 2
@@ -195,34 +198,34 @@
* all SGMII. RGMII is not supported on this board. Setting SGMII 5 and
* 6 to on board SGMII phys
*/
- fm_info_set_phy_address(FM1_DTSEC5, CONFIG_SYS_FM1_DTSEC5_PHY_ADDR);
- fm_info_set_phy_address(FM1_DTSEC6, CONFIG_SYS_FM1_DTSEC6_PHY_ADDR);
+ fm_info_set_phy_address(FM1_DTSEC5, CONFIG_SYS_FM1_ONBOARD_PHY1_ADDR);
+ fm_info_set_phy_address(FM1_DTSEC6, CONFIG_SYS_FM1_ONBOARD_PHY2_ADDR);
switch (serdes1_prtcl) {
case 0x29:
case 0x2a:
/* Serdes 1: A-B SGMII, Configuring DTSEC 5 and 6 */
- debug("Setting phy addresses for FM1_DTSEC5: %x and"
- "FM1_DTSEC6: %x\n", CONFIG_SYS_FM1_DTSEC5_PHY_ADDR,
- CONFIG_SYS_FM1_DTSEC6_PHY_ADDR);
+ debug("Set phy addresses for FM1_DTSEC5:%x, FM1_DTSEC6:%x\n",
+ CONFIG_SYS_FM1_ONBOARD_PHY1_ADDR,
+ CONFIG_SYS_FM1_ONBOARD_PHY2_ADDR);
fm_info_set_phy_address(FM1_DTSEC5,
- CONFIG_SYS_FM1_DTSEC5_PHY_ADDR);
+ CONFIG_SYS_FM1_ONBOARD_PHY1_ADDR);
fm_info_set_phy_address(FM1_DTSEC6,
- CONFIG_SYS_FM1_DTSEC6_PHY_ADDR);
+ CONFIG_SYS_FM1_ONBOARD_PHY2_ADDR);
break;
#ifdef CONFIG_PPC_B4420
case 0x17:
case 0x18:
/* Serdes 1: A-D SGMII, Configuring on board dual SGMII Phy */
- debug("Setting phy addresses for FM1_DTSEC3: %x and"
- "FM1_DTSEC4: %x\n", CONFIG_SYS_FM1_DTSEC5_PHY_ADDR,
- CONFIG_SYS_FM1_DTSEC6_PHY_ADDR);
+ debug("Set phy addresses for FM1_DTSEC3:%x, FM1_DTSEC4:%x\n",
+ CONFIG_SYS_FM1_ONBOARD_PHY1_ADDR,
+ CONFIG_SYS_FM1_ONBOARD_PHY2_ADDR);
/* Fixing Serdes clock by programming FPGA register */
QIXIS_WRITE(brdcfg[4], QIXIS_SRDS1CLK_125);
fm_info_set_phy_address(FM1_DTSEC3,
- CONFIG_SYS_FM1_DTSEC5_PHY_ADDR);
+ CONFIG_SYS_FM1_ONBOARD_PHY1_ADDR);
fm_info_set_phy_address(FM1_DTSEC4,
- CONFIG_SYS_FM1_DTSEC6_PHY_ADDR);
+ CONFIG_SYS_FM1_ONBOARD_PHY2_ADDR);
break;
#endif
default:
@@ -233,8 +236,8 @@
switch (serdes2_prtcl) {
case 0x17:
case 0x18:
- debug("Setting phy addresses on SGMII Riser card for"
- "FM1_DTSEC ports: \n");
+ debug("Set phy address on SGMII Riser for FM1_DTSEC1:%x\n",
+ CONFIG_SYS_FM1_DTSEC1_RISER_PHY_ADDR);
fm_info_set_phy_address(FM1_DTSEC1,
CONFIG_SYS_FM1_DTSEC1_RISER_PHY_ADDR);
fm_info_set_phy_address(FM1_DTSEC2,
@@ -246,8 +249,8 @@
break;
case 0x48:
case 0x49:
- debug("Setting phy addresses on SGMII Riser card for"
- "FM1_DTSEC ports: \n");
+ debug("Set phy address on SGMII Riser for FM1_DTSEC1:%x\n",
+ CONFIG_SYS_FM1_DTSEC1_RISER_PHY_ADDR);
fm_info_set_phy_address(FM1_DTSEC1,
CONFIG_SYS_FM1_DTSEC1_RISER_PHY_ADDR);
fm_info_set_phy_address(FM1_DTSEC2,
@@ -255,29 +258,37 @@
fm_info_set_phy_address(FM1_DTSEC3,
CONFIG_SYS_FM1_DTSEC3_RISER_PHY_ADDR);
break;
- case 0x8d:
+ case 0xb1:
case 0xb2:
- debug("Setting phy addresses on SGMII Riser card for"
- "FM1_DTSEC ports: \n");
+ case 0x8c:
+ case 0x8d:
+ debug("Set phy addresses on SGMII Riser for FM1_DTSEC1:%x\n",
+ CONFIG_SYS_FM1_DTSEC1_RISER_PHY_ADDR);
fm_info_set_phy_address(FM1_DTSEC3,
CONFIG_SYS_FM1_DTSEC1_RISER_PHY_ADDR);
fm_info_set_phy_address(FM1_DTSEC4,
CONFIG_SYS_FM1_DTSEC2_RISER_PHY_ADDR);
+ /*
+ * XFI does not need a PHY to work, but to make U-boot
+ * happy, assign a fake PHY address for a XFI port.
+ */
+ fm_info_set_phy_address(FM1_10GEC1, 0);
+ fm_info_set_phy_address(FM1_10GEC2, 1);
break;
case 0x98:
/* XAUI in Slot1 and Slot2 */
- debug("Setting phy addresses on B4860 QDS AMC2PEX-2S for FM1_10GEC1: %x\n",
+ debug("Set phy address of AMC2PEX-2S for FM1_10GEC1:%x\n",
CONFIG_SYS_FM1_10GEC1_PHY_ADDR);
fm_info_set_phy_address(FM1_10GEC1,
CONFIG_SYS_FM1_10GEC1_PHY_ADDR);
- debug("Setting phy addresses on B4860 QDS AMC2PEX-2S for FM1_10GEC2: %x\n",
+ debug("Set phy address of AMC2PEX-2S for FM1_10GEC2:%x\n",
CONFIG_SYS_FM1_10GEC2_PHY_ADDR);
fm_info_set_phy_address(FM1_10GEC2,
CONFIG_SYS_FM1_10GEC2_PHY_ADDR);
break;
case 0x9E:
/* XAUI in Slot2 */
- debug("Setting phy addresses on B4860 QDS AMC2PEX-2S for FM1_10GEC2: %x\n",
+ debug("Sett phy address of AMC2PEX-2S for FM1_10GEC2:%x\n",
CONFIG_SYS_FM1_10GEC2_PHY_ADDR);
fm_info_set_phy_address(FM1_10GEC2,
CONFIG_SYS_FM1_10GEC2_PHY_ADDR);
@@ -329,17 +340,20 @@
switch (fm_info_get_enet_if(i)) {
case PHY_INTERFACE_MODE_XGMII:
fm_info_set_mdio(i,
- miiphy_get_dev_by_name(DEFAULT_FM_TGEC_MDIO_NAME));
+ miiphy_get_dev_by_name
+ (DEFAULT_FM_TGEC_MDIO_NAME));
+ break;
+ case PHY_INTERFACE_MODE_NONE:
+ fm_info_set_phy_address(i, 0);
break;
default:
- printf("Fman1: 10GSEC%u set to unknown interface %i\n",
+ printf("Fman1: TGEC%u set to unknown interface %i\n",
idx + 1, fm_info_get_enet_if(i));
fm_info_set_phy_address(i, 0);
break;
}
}
-
cpu_eth_init(bis);
#endif
@@ -351,21 +365,82 @@
{
int phy;
char alias[32];
+ struct fixed_link f_link;
+ ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
+ u32 prtcl2 = in_be32(&gur->rcwsr[4]) & FSL_CORENET2_RCWSR4_SRDS2_PRTCL;
+
+ prtcl2 >>= FSL_CORENET2_RCWSR4_SRDS2_PRTCL_SHIFT;
if (fm_info_get_enet_if(port) == PHY_INTERFACE_MODE_SGMII) {
phy = fm_info_get_phy_address(port);
sprintf(alias, "phy_sgmii_%x", phy);
fdt_set_phy_handle(fdt, compat, addr, alias);
+ fdt_status_okay_by_alias(fdt, alias);
+ } else if (fm_info_get_enet_if(port) == PHY_INTERFACE_MODE_XGMII) {
+ /* check if it's XFI interface for 10g */
+ switch (prtcl2) {
+ case 0x80:
+ case 0x81:
+ case 0x82:
+ case 0x83:
+ case 0x84:
+ case 0x85:
+ case 0x86:
+ case 0x87:
+ case 0x88:
+ case 0x89:
+ case 0x8a:
+ case 0x8b:
+ case 0x8c:
+ case 0x8d:
+ case 0x8e:
+ case 0xb1:
+ case 0xb2:
+ f_link.phy_id = port;
+ f_link.duplex = 1;
+ f_link.link_speed = 10000;
+ f_link.pause = 0;
+ f_link.asym_pause = 0;
+
+ fdt_delprop(fdt, offset, "phy-handle");
+ fdt_setprop(fdt, offset, "fixed-link", &f_link,
+ sizeof(f_link));
+ break;
+ case 0x98: /* XAUI interface */
+ sprintf(alias, "phy_xaui_slot1");
+ fdt_status_okay_by_alias(fdt, alias);
+
+ sprintf(alias, "phy_xaui_slot2");
+ fdt_status_okay_by_alias(fdt, alias);
+ break;
+ case 0x9e: /* XAUI interface */
+ case 0x9a:
+ case 0x93:
+ case 0x91:
+ sprintf(alias, "phy_xaui_slot1");
+ fdt_status_okay_by_alias(fdt, alias);
+ break;
+ case 0x97: /* XAUI interface */
+ case 0xc3:
+ sprintf(alias, "phy_xaui_slot2");
+ fdt_status_okay_by_alias(fdt, alias);
+ break;
+ default:
+ break;
+ }
}
}
+/*
+ * Set status to disabled for unused ethernet node
+ */
void fdt_fixup_board_enet(void *fdt)
{
int i;
char alias[32];
- for (i = FM1_DTSEC1; i < FM1_DTSEC1 + CONFIG_SYS_NUM_FM1_DTSEC; i++) {
+ for (i = FM1_DTSEC1; i <= FM1_10GEC2; i++) {
switch (fm_info_get_enet_if(i)) {
case PHY_INTERFACE_MODE_NONE:
sprintf(alias, "ethernet%u", i);
diff --git a/board/freescale/b4860qds/law.c b/board/freescale/b4860qds/law.c
index 5b327cc..047c3cb 100644
--- a/board/freescale/b4860qds/law.c
+++ b/board/freescale/b4860qds/law.c
@@ -17,9 +17,6 @@
SET_LAW(CONFIG_SYS_QMAN_MEM_PHYS, LAW_SIZE_32M, LAW_TRGT_IF_QMAN),
#endif
SET_LAW(QIXIS_BASE_PHYS, LAW_SIZE_4K, LAW_TRGT_IF_IFC),
-#ifdef CONFIG_SYS_MAPLE_MEM_PHYS
- SET_LAW(CONFIG_SYS_MAPLE_MEM_PHYS, LAW_SIZE_16M, LAW_TRGT_IF_MAPLE),
-#endif
#ifdef CONFIG_SYS_DCSRBAR_PHYS
/* Limit DCSR to 32M to access NPC Trace Buffer */
SET_LAW(CONFIG_SYS_DCSRBAR_PHYS, LAW_SIZE_32M, LAW_TRGT_IF_DCSR),
diff --git a/board/freescale/common/Makefile b/board/freescale/common/Makefile
index 25a1bc1..59ddeef 100644
--- a/board/freescale/common/Makefile
+++ b/board/freescale/common/Makefile
@@ -23,6 +23,7 @@
obj-$(CONFIG_FSL_PIXIS) += pixis.o
ifndef CONFIG_SPL_BUILD
obj-$(CONFIG_FSL_NGPIXIS) += ngpixis.o
+obj-$(CONFIG_VID) += vid.o
endif
obj-$(CONFIG_FSL_QIXIS) += qixis.o
obj-$(CONFIG_PQ_MDS_PIB) += pq-mds-pib.o
diff --git a/board/freescale/common/vid.c b/board/freescale/common/vid.c
new file mode 100644
index 0000000..6b8af14
--- /dev/null
+++ b/board/freescale/common/vid.c
@@ -0,0 +1,491 @@
+/*
+ * Copyright 2014 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <command.h>
+#include <i2c.h>
+#include <asm/immap_85xx.h>
+#include "vid.h"
+
+DECLARE_GLOBAL_DATA_PTR;
+
+int __weak i2c_multiplexer_select_vid_channel(u8 channel)
+{
+ return 0;
+}
+
+/*
+ * Compensate for a board specific voltage drop between regulator and SoC
+ * return a value in mV
+ */
+int __weak board_vdd_drop_compensation(void)
+{
+ return 0;
+}
+
+/*
+ * Get the i2c address configuration for the IR regulator chip
+ *
+ * There are some variance in the RDB HW regarding the I2C address configuration
+ * for the IR regulator chip, which is likely a problem of external resistor
+ * accuracy. So we just check each address in a hopefully non-intrusive mode
+ * and use the first one that seems to work
+ *
+ * The IR chip can show up under the following addresses:
+ * 0x08 (Verified on T1040RDB-PA,T4240RDB-PB,X-T4240RDB-16GPA)
+ * 0x09 (Verified on T1040RDB-PA)
+ * 0x38 (Verified on T2080QDS, T2081QDS)
+ */
+static int find_ir_chip_on_i2c(void)
+{
+ int i2caddress;
+ int ret;
+ u8 byte;
+ int i;
+ const int ir_i2c_addr[] = {0x38, 0x08, 0x09};
+
+ /* Check all the address */
+ for (i = 0; i < (sizeof(ir_i2c_addr)/sizeof(ir_i2c_addr[0])); i++) {
+ i2caddress = ir_i2c_addr[i];
+ ret = i2c_read(i2caddress,
+ IR36021_MFR_ID_OFFSET, 1, (void *)&byte,
+ sizeof(byte));
+ if ((ret >= 0) && (byte == IR36021_MFR_ID))
+ return i2caddress;
+ }
+ return -1;
+}
+
+/* Maximum loop count waiting for new voltage to take effect */
+#define MAX_LOOP_WAIT_NEW_VOL 100
+/* Maximum loop count waiting for the voltage to be stable */
+#define MAX_LOOP_WAIT_VOL_STABLE 100
+/*
+ * read_voltage from sensor on I2C bus
+ * We use average of 4 readings, waiting for WAIT_FOR_ADC before
+ * another reading
+ */
+#define NUM_READINGS 4 /* prefer to be power of 2 for efficiency */
+
+/* If an INA220 chip is available, we can use it to read back the voltage
+ * as it may have a higher accuracy than the IR chip for the same purpose
+ */
+#ifdef CONFIG_VOL_MONITOR_INA220
+#define WAIT_FOR_ADC 532 /* wait for 532 microseconds for ADC */
+#define ADC_MIN_ACCURACY 4
+#else
+#define WAIT_FOR_ADC 138 /* wait for 138 microseconds for ADC */
+#define ADC_MIN_ACCURACY 4
+#endif
+
+#ifdef CONFIG_VOL_MONITOR_INA220
+static int read_voltage_from_INA220(int i2caddress)
+{
+ int i, ret, voltage_read = 0;
+ u16 vol_mon;
+ u8 buf[2];
+
+ for (i = 0; i < NUM_READINGS; i++) {
+ ret = i2c_read(I2C_VOL_MONITOR_ADDR,
+ I2C_VOL_MONITOR_BUS_V_OFFSET, 1,
+ (void *)&buf, 2);
+ if (ret) {
+ printf("VID: failed to read core voltage\n");
+ return ret;
+ }
+ vol_mon = (buf[0] << 8) | buf[1];
+ if (vol_mon & I2C_VOL_MONITOR_BUS_V_OVF) {
+ printf("VID: Core voltage sensor error\n");
+ return -1;
+ }
+ debug("VID: bus voltage reads 0x%04x\n", vol_mon);
+ /* LSB = 4mv */
+ voltage_read += (vol_mon >> I2C_VOL_MONITOR_BUS_V_SHIFT) * 4;
+ udelay(WAIT_FOR_ADC);
+ }
+ /* calculate the average */
+ voltage_read /= NUM_READINGS;
+
+ return voltage_read;
+}
+#endif
+
+/* read voltage from IR */
+#ifdef CONFIG_VOL_MONITOR_IR36021_READ
+static int read_voltage_from_IR(int i2caddress)
+{
+ int i, ret, voltage_read = 0;
+ u16 vol_mon;
+ u8 buf;
+
+ for (i = 0; i < NUM_READINGS; i++) {
+ ret = i2c_read(i2caddress,
+ IR36021_LOOP1_VOUT_OFFSET,
+ 1, (void *)&buf, 1);
+ if (ret) {
+ printf("VID: failed to read vcpu\n");
+ return ret;
+ }
+ vol_mon = buf;
+ if (!vol_mon) {
+ printf("VID: Core voltage sensor error\n");
+ return -1;
+ }
+ debug("VID: bus voltage reads 0x%02x\n", vol_mon);
+ /* Resolution is 1/128V. We scale up here to get 1/128mV
+ * and divide at the end
+ */
+ voltage_read += vol_mon * 1000;
+ udelay(WAIT_FOR_ADC);
+ }
+ /* Scale down to the real mV as IR resolution is 1/128V, rounding up */
+ voltage_read = DIV_ROUND_UP(voltage_read, 128);
+
+ /* calculate the average */
+ voltage_read /= NUM_READINGS;
+
+ /* Compensate for a board specific voltage drop between regulator and
+ * SoC before converting into an IR VID value
+ */
+ voltage_read -= board_vdd_drop_compensation();
+
+ return voltage_read;
+}
+#endif
+
+static int read_voltage(int i2caddress)
+{
+ int voltage_read;
+#ifdef CONFIG_VOL_MONITOR_INA220
+ voltage_read = read_voltage_from_INA220(i2caddress);
+#elif defined CONFIG_VOL_MONITOR_IR36021_READ
+ voltage_read = read_voltage_from_IR(i2caddress);
+#else
+ return -1;
+#endif
+ return voltage_read;
+}
+
+/*
+ * We need to calculate how long before the voltage stops to drop
+ * or increase. It returns with the loop count. Each loop takes
+ * several readings (WAIT_FOR_ADC)
+ */
+static int wait_for_new_voltage(int vdd, int i2caddress)
+{
+ int timeout, vdd_current;
+
+ vdd_current = read_voltage(i2caddress);
+ /* wait until voltage starts to reach the target. Voltage slew
+ * rates by typical regulators will always lead to stable readings
+ * within each fairly long ADC interval in comparison to the
+ * intended voltage delta change until the target voltage is
+ * reached. The fairly small voltage delta change to any target
+ * VID voltage also means that this function will always complete
+ * within few iterations. If the timeout was ever reached, it would
+ * point to a serious failure in the regulator system.
+ */
+ for (timeout = 0;
+ abs(vdd - vdd_current) > (IR_VDD_STEP_UP + IR_VDD_STEP_DOWN) &&
+ timeout < MAX_LOOP_WAIT_NEW_VOL; timeout++) {
+ vdd_current = read_voltage(i2caddress);
+ }
+ if (timeout >= MAX_LOOP_WAIT_NEW_VOL) {
+ printf("VID: Voltage adjustment timeout\n");
+ return -1;
+ }
+ return timeout;
+}
+
+/*
+ * this function keeps reading the voltage until it is stable or until the
+ * timeout expires
+ */
+static int wait_for_voltage_stable(int i2caddress)
+{
+ int timeout, vdd_current, vdd;
+
+ vdd = read_voltage(i2caddress);
+ udelay(NUM_READINGS * WAIT_FOR_ADC);
+
+ /* wait until voltage is stable */
+ vdd_current = read_voltage(i2caddress);
+ /* The maximum timeout is
+ * MAX_LOOP_WAIT_VOL_STABLE * NUM_READINGS * WAIT_FOR_ADC
+ */
+ for (timeout = MAX_LOOP_WAIT_VOL_STABLE;
+ abs(vdd - vdd_current) > ADC_MIN_ACCURACY &&
+ timeout > 0; timeout--) {
+ vdd = vdd_current;
+ udelay(NUM_READINGS * WAIT_FOR_ADC);
+ vdd_current = read_voltage(i2caddress);
+ }
+ if (timeout == 0)
+ return -1;
+ return vdd_current;
+}
+
+#ifdef CONFIG_VOL_MONITOR_IR36021_SET
+/* Set the voltage to the IR chip */
+static int set_voltage_to_IR(int i2caddress, int vdd)
+{
+ int wait, vdd_last;
+ int ret;
+ u8 vid;
+
+ /* Compensate for a board specific voltage drop between regulator and
+ * SoC before converting into an IR VID value
+ */
+ vdd += board_vdd_drop_compensation();
+ vid = DIV_ROUND_UP(vdd - 245, 5);
+
+ ret = i2c_write(i2caddress, IR36021_LOOP1_MANUAL_ID_OFFSET,
+ 1, (void *)&vid, sizeof(vid));
+ if (ret) {
+ printf("VID: failed to write VID\n");
+ return -1;
+ }
+ wait = wait_for_new_voltage(vdd, i2caddress);
+ if (wait < 0)
+ return -1;
+ debug("VID: Waited %d us\n", wait * NUM_READINGS * WAIT_FOR_ADC);
+
+ vdd_last = wait_for_voltage_stable(i2caddress);
+ if (vdd_last < 0)
+ return -1;
+ debug("VID: Current voltage is %d mV\n", vdd_last);
+ return vdd_last;
+}
+#endif
+
+static int set_voltage(int i2caddress, int vdd)
+{
+ int vdd_last = -1;
+
+#ifdef CONFIG_VOL_MONITOR_IR36021_SET
+ vdd_last = set_voltage_to_IR(i2caddress, vdd);
+#else
+ #error Specific voltage monitor must be defined
+#endif
+ return vdd_last;
+}
+
+int adjust_vdd(ulong vdd_override)
+{
+ int re_enable = disable_interrupts();
+ ccsr_gur_t __iomem *gur =
+ (void __iomem *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
+ u32 fusesr;
+ u8 vid;
+ int vdd_target, vdd_current, vdd_last;
+ int ret, i2caddress;
+ unsigned long vdd_string_override;
+ char *vdd_string;
+ static const uint16_t vdd[32] = {
+ 0, /* unused */
+ 9875, /* 0.9875V */
+ 9750,
+ 9625,
+ 9500,
+ 9375,
+ 9250,
+ 9125,
+ 9000,
+ 8875,
+ 8750,
+ 8625,
+ 8500,
+ 8375,
+ 8250,
+ 8125,
+ 10000, /* 1.0000V */
+ 10125,
+ 10250,
+ 10375,
+ 10500,
+ 10625,
+ 10750,
+ 10875,
+ 11000,
+ 0, /* reserved */
+ };
+ struct vdd_drive {
+ u8 vid;
+ unsigned voltage;
+ };
+
+ ret = i2c_multiplexer_select_vid_channel(I2C_MUX_CH_VOL_MONITOR);
+ if (ret) {
+ debug("VID: I2C failed to switch channel\n");
+ ret = -1;
+ goto exit;
+ }
+ ret = find_ir_chip_on_i2c();
+ if (ret < 0) {
+ printf("VID: Could not find voltage regulator on I2C.\n");
+ ret = -1;
+ goto exit;
+ } else {
+ i2caddress = ret;
+ debug("VID: IR Chip found on I2C address 0x%02x\n", i2caddress);
+ }
+
+ /* get the voltage ID from fuse status register */
+ fusesr = in_be32(&gur->dcfg_fusesr);
+ /*
+ * VID is used according to the table below
+ * ---------------------------------------
+ * | DA_V |
+ * |-------------------------------------|
+ * | 5b00000 | 5b00001-5b11110 | 5b11111 |
+ * ---------------+---------+-----------------+---------|
+ * | D | 5b00000 | NO VID | VID = DA_V | NO VID |
+ * | A |----------+---------+-----------------+---------|
+ * | _ | 5b00001 |VID = | VID = |VID = |
+ * | V | ~ | DA_V_ALT| DA_V_ALT | DA_A_VLT|
+ * | _ | 5b11110 | | | |
+ * | A |----------+---------+-----------------+---------|
+ * | L | 5b11111 | No VID | VID = DA_V | NO VID |
+ * | T | | | | |
+ * ------------------------------------------------------
+ */
+ vid = (fusesr >> FSL_CORENET_DCFG_FUSESR_ALTVID_SHIFT) &
+ FSL_CORENET_DCFG_FUSESR_ALTVID_MASK;
+ if ((vid == 0) || (vid == FSL_CORENET_DCFG_FUSESR_ALTVID_MASK)) {
+ vid = (fusesr >> FSL_CORENET_DCFG_FUSESR_VID_SHIFT) &
+ FSL_CORENET_DCFG_FUSESR_VID_MASK;
+ }
+ vdd_target = vdd[vid];
+
+ /* check override variable for overriding VDD */
+ vdd_string = getenv(CONFIG_VID_FLS_ENV);
+ if (vdd_override == 0 && vdd_string &&
+ !strict_strtoul(vdd_string, 10, &vdd_string_override))
+ vdd_override = vdd_string_override;
+ if (vdd_override >= VDD_MV_MIN && vdd_override <= VDD_MV_MAX) {
+ vdd_target = vdd_override * 10; /* convert to 1/10 mV */
+ debug("VDD override is %lu\n", vdd_override);
+ } else if (vdd_override != 0) {
+ printf("Invalid value.\n");
+ }
+ if (vdd_target == 0) {
+ debug("VID: VID not used\n");
+ ret = 0;
+ goto exit;
+ } else {
+ /* divide and round up by 10 to get a value in mV */
+ vdd_target = DIV_ROUND_UP(vdd_target, 10);
+ debug("VID: vid = %d mV\n", vdd_target);
+ }
+
+ /*
+ * Read voltage monitor to check real voltage.
+ */
+ vdd_last = read_voltage(i2caddress);
+ if (vdd_last < 0) {
+ printf("VID: Couldn't read sensor abort VID adjustment\n");
+ ret = -1;
+ goto exit;
+ }
+ vdd_current = vdd_last;
+ debug("VID: Core voltage is currently at %d mV\n", vdd_last);
+ /*
+ * Adjust voltage to at or one step above target.
+ * As measurements are less precise than setting the values
+ * we may run through dummy steps that cancel each other
+ * when stepping up and then down.
+ */
+ while (vdd_last > 0 &&
+ vdd_last < vdd_target) {
+ vdd_current += IR_VDD_STEP_UP;
+ vdd_last = set_voltage(i2caddress, vdd_current);
+ }
+ while (vdd_last > 0 &&
+ vdd_last > vdd_target + (IR_VDD_STEP_DOWN - 1)) {
+ vdd_current -= IR_VDD_STEP_DOWN;
+ vdd_last = set_voltage(i2caddress, vdd_current);
+ }
+
+ if (vdd_last > 0)
+ printf("VID: Core voltage after adjustment is at %d mV\n",
+ vdd_last);
+ else
+ ret = -1;
+exit:
+ if (re_enable)
+ enable_interrupts();
+ return ret;
+}
+
+static int print_vdd(void)
+{
+ int vdd_last, ret, i2caddress;
+
+ ret = i2c_multiplexer_select_vid_channel(I2C_MUX_CH_VOL_MONITOR);
+ if (ret) {
+ debug("VID : I2c failed to switch channel\n");
+ return -1;
+ }
+ ret = find_ir_chip_on_i2c();
+ if (ret < 0) {
+ printf("VID: Could not find voltage regulator on I2C.\n");
+ return -1;
+ } else {
+ i2caddress = ret;
+ debug("VID: IR Chip found on I2C address 0x%02x\n", i2caddress);
+ }
+
+ /*
+ * Read voltage monitor to check real voltage.
+ */
+ vdd_last = read_voltage(i2caddress);
+ if (vdd_last < 0) {
+ printf("VID: Couldn't read sensor abort VID adjustment\n");
+ return -1;
+ }
+ printf("VID: Core voltage is at %d mV\n", vdd_last);
+
+ return 0;
+}
+
+static int do_vdd_override(cmd_tbl_t *cmdtp,
+ int flag, int argc,
+ char * const argv[])
+{
+ ulong override;
+
+ if (argc < 2)
+ return CMD_RET_USAGE;
+
+ if (!strict_strtoul(argv[1], 10, &override))
+ adjust_vdd(override); /* the value is checked by callee */
+ else
+ return CMD_RET_USAGE;
+ return 0;
+}
+
+static int do_vdd_read(cmd_tbl_t *cmdtp,
+ int flag, int argc,
+ char * const argv[])
+{
+ if (argc < 1)
+ return CMD_RET_USAGE;
+ print_vdd();
+
+ return 0;
+}
+
+U_BOOT_CMD(
+ vdd_override, 2, 0, do_vdd_override,
+ "override VDD",
+ " - override with the voltage specified in mV, eg. 1050"
+);
+
+U_BOOT_CMD(
+ vdd_read, 1, 0, do_vdd_read,
+ "read VDD",
+ " - Read the voltage specified in mV"
+)
diff --git a/board/freescale/common/vid.h b/board/freescale/common/vid.h
new file mode 100644
index 0000000..a9c7bb4
--- /dev/null
+++ b/board/freescale/common/vid.h
@@ -0,0 +1,20 @@
+/*
+ * Copyright 2014 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#ifndef __VID_H_
+#define __VID_H_
+
+#define IR36021_LOOP1_MANUAL_ID_OFFSET 0x6A
+#define IR36021_LOOP1_VOUT_OFFSET 0x9A
+#define IR36021_MFR_ID_OFFSET 0x92
+#define IR36021_MFR_ID 0x43
+
+/* step the IR regulator in 5mV increments */
+#define IR_VDD_STEP_DOWN 5
+#define IR_VDD_STEP_UP 5
+int adjust_vdd(ulong vdd_override);
+
+#endif /* __VID_H_ */
diff --git a/board/freescale/common/vsc3316_3308.c b/board/freescale/common/vsc3316_3308.c
index 97a25e8..dd9c37e 100644
--- a/board/freescale/common/vsc3316_3308.c
+++ b/board/freescale/common/vsc3316_3308.c
@@ -13,7 +13,12 @@
#define INPUT_STATE_REG 0x13
#define GLOBAL_INPUT_ISE1 0x51
#define GLOBAL_INPUT_ISE2 0x52
+#define GLOBAL_INPUT_GAIN 0x53
#define GLOBAL_INPUT_LOS 0x55
+#define GLOBAL_OUTPUT_PE1 0x56
+#define GLOBAL_OUTPUT_PE2 0x57
+#define GLOBAL_OUTPUT_LEVEL 0x58
+#define GLOBAL_OUTPUT_TERMINATION 0x5A
#define GLOBAL_CORE_CNTRL 0x5D
#define OUTPUT_MODE_PAGE 0x23
#define CORE_CONTROL_PAGE 0x25
@@ -92,6 +97,109 @@
return 0;
}
+#ifdef CONFIG_SYS_FSL_B4860QDS_XFI_ERR
+int vsc3308_config_adjust(unsigned int vsc_addr, const int8_t con_arr[][2],
+ unsigned int num_con)
+{
+ unsigned int i;
+ u8 rev_id = 0;
+ int ret;
+
+ debug("VSC:Initializing VSC3308 at I2C address 0x%x for Tx\n",
+ vsc_addr);
+
+ ret = i2c_read(vsc_addr, REVISION_ID_REG, 1, &rev_id, 1);
+ if (ret < 0) {
+ printf("VSC:0x%x could not read REV_ID from device.\n",
+ vsc_addr);
+ return ret;
+ }
+
+ if (rev_id != 0xab) {
+ printf("VSC: device at address 0x%x is not VSC3316/3308.\n",
+ vsc_addr);
+ return -ENODEV;
+ }
+
+ ret = vsc_if_enable(vsc_addr);
+ if (ret) {
+ printf("VSC:0x%x could not configured for 2-wire I/F.\n",
+ vsc_addr);
+ return ret;
+ }
+
+ /* config connections - page 0x00 */
+ i2c_reg_write(vsc_addr, CURRENT_PAGE_REGISTER, CONNECTION_CONFIG_PAGE);
+
+ /* Configure Global Input ISE */
+ i2c_reg_write(vsc_addr, GLOBAL_INPUT_ISE1, 0);
+ i2c_reg_write(vsc_addr, GLOBAL_INPUT_ISE2, 0);
+
+ /* Configure Tx/Rx Global Output PE1 */
+ i2c_reg_write(vsc_addr, GLOBAL_OUTPUT_PE1, 0);
+
+ /* Configure Tx/Rx Global Output PE2 */
+ i2c_reg_write(vsc_addr, GLOBAL_OUTPUT_PE2, 0);
+
+ /* Configure Tx/Rx Global Input GAIN */
+ i2c_reg_write(vsc_addr, GLOBAL_INPUT_GAIN, 0x3F);
+
+ /* Setting Global Input LOS threshold value */
+ i2c_reg_write(vsc_addr, GLOBAL_INPUT_LOS, 0xE0);
+
+ /* Setting Global output termination */
+ i2c_reg_write(vsc_addr, GLOBAL_OUTPUT_TERMINATION, 0);
+
+ /* Configure Tx/Rx Global Output level */
+ if (vsc_addr == VSC3308_TX_ADDRESS)
+ i2c_reg_write(vsc_addr, GLOBAL_OUTPUT_LEVEL, 4);
+ else
+ i2c_reg_write(vsc_addr, GLOBAL_OUTPUT_LEVEL, 2);
+
+ /* Making crosspoint connections, by connecting required
+ * input to output */
+ for (i = 0; i < num_con ; i++)
+ i2c_reg_write(vsc_addr, con_arr[i][1], con_arr[i][0]);
+
+ /* input state - page 0x13 */
+ i2c_reg_write(vsc_addr, CURRENT_PAGE_REGISTER, INPUT_STATE_REG);
+ /* Turning off all the required input of the switch */
+ for (i = 0; i < num_con; i++)
+ i2c_reg_write(vsc_addr, con_arr[i][0], 1);
+
+ /* only turn on specific Tx/Rx requested by the XFI erratum */
+ if (vsc_addr == VSC3308_TX_ADDRESS) {
+ i2c_reg_write(vsc_addr, 2, 0);
+ i2c_reg_write(vsc_addr, 3, 0);
+ } else {
+ i2c_reg_write(vsc_addr, 0, 0);
+ i2c_reg_write(vsc_addr, 1, 0);
+ }
+
+ /* config output mode - page 0x23 */
+ i2c_reg_write(vsc_addr, CURRENT_PAGE_REGISTER, OUTPUT_MODE_PAGE);
+ /* Turn off the Output driver correspond to required output*/
+ for (i = 0; i < num_con ; i++)
+ i2c_reg_write(vsc_addr, con_arr[i][1], 1);
+
+ /* only turn on specific Tx/Rx requested by the XFI erratum */
+ if (vsc_addr == VSC3308_TX_ADDRESS) {
+ i2c_reg_write(vsc_addr, 0, 0);
+ i2c_reg_write(vsc_addr, 1, 0);
+ } else {
+ i2c_reg_write(vsc_addr, 3, 0);
+ i2c_reg_write(vsc_addr, 4, 0);
+ }
+
+ /* configure global core control register, Turn on Global core power */
+ i2c_reg_write(vsc_addr, GLOBAL_CORE_CNTRL, 0);
+
+ vsc_wp_config(vsc_addr);
+
+ return 0;
+}
+#endif
+
int vsc3308_config(unsigned int vsc_addr, const int8_t con_arr[][2],
unsigned int num_con)
{
diff --git a/board/freescale/common/vsc3316_3308.h b/board/freescale/common/vsc3316_3308.h
index 2a49187..d722ea3 100644
--- a/board/freescale/common/vsc3316_3308.h
+++ b/board/freescale/common/vsc3316_3308.h
@@ -14,6 +14,10 @@
int vsc_if_enable(unsigned int vsc_addr);
int vsc3316_config(unsigned int vsc_addr, int8_t con_arr[][2],
unsigned int num_con);
+#ifdef CONFIG_SYS_FSL_B4860QDS_XFI_ERR
+int vsc3308_config_adjust(unsigned int vsc_addr, const int8_t con_arr[][2],
+ unsigned int num_con);
+#endif
int vsc3308_config(unsigned int vsc_addr, const int8_t con_arr[][2],
unsigned int num_con);
void vsc_wp_config(unsigned int vsc_addr);
diff --git a/board/freescale/corenet_ds/eth_hydra.c b/board/freescale/corenet_ds/eth_hydra.c
index 35825c4..396103f 100644
--- a/board/freescale/corenet_ds/eth_hydra.c
+++ b/board/freescale/corenet_ds/eth_hydra.c
@@ -62,7 +62,7 @@
#ifdef CONFIG_FMAN_ENET
-#define BRDCFG1_EMI1_SEL_MASK 0x70
+#define BRDCFG1_EMI1_SEL_MASK 0x78
#define BRDCFG1_EMI1_SEL_SLOT1 0x10
#define BRDCFG1_EMI1_SEL_SLOT2 0x20
#define BRDCFG1_EMI1_SEL_SLOT5 0x30
@@ -202,6 +202,8 @@
if (!path)
path = alias;
+ do_fixup_by_path(fdt, path, "reg",
+ &mux, sizeof(mux), 1);
do_fixup_by_path(fdt, path, "fsl,hydra-mdio-muxval",
&mux, sizeof(mux), 1);
}
@@ -250,11 +252,12 @@
return;
}
- if (mux == BRDCFG1_EMI1_SEL_RGMII) {
+ if (mux == (BRDCFG1_EMI1_SEL_RGMII | BRDCFG1_EMI1_EN)) {
/* RGMII */
/* The RGMII PHY is identified by the MAC connected to it */
sprintf(phy, "phy_rgmii_%u", port == FM1_DTSEC4 ? 0 : 1);
fdt_set_phy_handle(fdt, compat, addr, phy);
+ return;
}
/* If it's not RGMII or XGMII, it must be SGMII */
diff --git a/board/freescale/t102xqds/Kconfig b/board/freescale/t102xqds/Kconfig
new file mode 100644
index 0000000..4d17798
--- /dev/null
+++ b/board/freescale/t102xqds/Kconfig
@@ -0,0 +1,12 @@
+if TARGET_T102XQDS
+
+config SYS_BOARD
+ default "t102xqds"
+
+config SYS_VENDOR
+ default "freescale"
+
+config SYS_CONFIG_NAME
+ default "T102xQDS"
+
+endif
diff --git a/board/freescale/t102xqds/MAINTAINERS b/board/freescale/t102xqds/MAINTAINERS
new file mode 100644
index 0000000..1ffccc4
--- /dev/null
+++ b/board/freescale/t102xqds/MAINTAINERS
@@ -0,0 +1,12 @@
+T102XQDS BOARD
+M: Shengzhou Liu <Shengzhou.Liu@freescale.com>
+S: Maintained
+F: board/freescale/t102xqds/
+F: include/configs/T102xQDS.h
+F: configs/T1024QDS_defconfig
+F: configs/T1024QDS_NAND_defconfig
+F: configs/T1024QDS_SDCARD_defconfig
+F: configs/T1024QDS_SPIFLASH_defconfig
+F: configs/T1024QDS_D4_defconfig
+F: configs/T1024QDS_SECURE_BOOT_defconfig
+F: configs/T1024QDS_D4_SECURE_BOOT_defconfig
diff --git a/board/freescale/t102xqds/Makefile b/board/freescale/t102xqds/Makefile
new file mode 100644
index 0000000..d94f230
--- /dev/null
+++ b/board/freescale/t102xqds/Makefile
@@ -0,0 +1,17 @@
+#
+# Copyright 2014 Freescale Semiconductor, Inc.
+#
+# SPDX-License-Identifier: GPL-2.0+
+#
+
+ifdef CONFIG_SPL_BUILD
+obj-y += spl.o
+else
+obj-y += t102xqds.o
+obj-y += eth_t102xqds.o
+obj-$(CONFIG_PCI) += pci.o
+obj-$(CONFIG_FSL_DIU_FB) += ../t1040qds/diu.o
+endif
+obj-y += ddr.o
+obj-y += law.o
+obj-y += tlb.o
diff --git a/board/freescale/t102xqds/README b/board/freescale/t102xqds/README
new file mode 100644
index 0000000..bb0f280
--- /dev/null
+++ b/board/freescale/t102xqds/README
@@ -0,0 +1,328 @@
+T1024 SoC Overview
+------------------
+The T1024/T1023 dual core and T1014/T1013 single core QorIQ communication processor
+combines two or one 64-bit Power Architecture e5500 core respectively with high
+performance datapath acceleration logic, and network peripheral bus interfaces
+required for networking and telecommunications. This processor can be used in
+applications such as enterprise WLAN access points, routers, switches, firewall
+and other packet processing intensive small enterprise and branch office appliances,
+and general-purpose embedded computing. Its high level of integration offers
+significant performance benefits and greatly helps to simplify board design.
+
+
+The T1024 SoC includes the following function and features:
+- two e5500 cores, each with a private 256 KB L2 cache
+ - Up to 1.4 GHz with 64-bit ISA support (Power Architecture v2.06-compliant)
+ - Three levels of instructions: User, supervisor, and hypervisor
+ - Independent boot and reset
+ - Secure boot capability
+- 256 KB shared L3 CoreNet platform cache (CPC)
+- Interconnect CoreNet platform
+ - CoreNet coherency manager supporting coherent and noncoherent transactions
+ with prioritization and bandwidth allocation amongst CoreNet endpoints
+ - 150 Gbps coherent read bandwidth
+- 32-/64-bit DDR3L/DDR4 SDRAM memory controller with ECC and interleaving support
+- Data Path Acceleration Architecture (DPAA) incorporating acceleration for the following functions:
+ - Packet parsing, classification, and distribution
+ - Queue management for scheduling, packet sequencing, and congestion management
+ - Cryptography Acceleration (SEC 5.x)
+ - IEEE 1588 support
+ - Hardware buffer management for buffer allocation and deallocation
+ - MACSEC on DPAA-based Ethernet ports
+- Ethernet interfaces
+ - Four 1 Gbps Ethernet controllers
+- Parallel Ethernet interfaces
+ - Two RGMII interfaces
+- High speed peripheral interfaces
+ - Three PCI Express 2.0 controllers/ports running at up to 5 GHz
+ - One SATA controller supporting 1.5 and 3.0 Gb/s operation
+ - One QSGMII interface
+ - Four SGMII interface supporting 1000 Mbps
+ - Three SGMII interfaces supporting up to 2500 Mbps
+ - 10GbE XFI or 10Base-KR interface
+- Additional peripheral interfaces
+ - Two USB 2.0 controllers with integrated PHY
+ - SD/eSDHC/eMMC
+ - eSPI controller
+ - Four I2C controllers
+ - Four UARTs
+ - Four GPIO controllers
+ - Integrated flash controller (IFC)
+ - LCD interface (DIU) with 12 bit dual data rate
+- Multicore programmable interrupt controller (PIC)
+- Two 8-channel DMA engines
+- Single source clocking implementation
+- Deep Sleep power implementaion (wakeup from GPIO/Timer/Ethernet/USB)
+- QUICC Engine block
+ - 32-bit RISC controller for flexible support of the communications peripherals
+ - Serial DMA channel for receive and transmit on all serial channels
+ - Two universal communication controllers, supporting TDM, HDLC, and UART
+
+T1023 Personality
+------------------
+T1023 is a reduced personality of T1024 without QUICC Engine, DIU, and
+unavailable deep sleep. Rest of the blocks are almost same as T1024.
+Differences between T1024 and T1023
+Feature T1024 T1023
+QUICC Engine: yes no
+DIU: yes no
+Deep Sleep: yes no
+I2C controller: 4 3
+DDR: 64-bit 32-bit
+IFC: 32-bit 28-bit
+
+
+T1024QDS board Overview
+-----------------------
+- SERDES Connections
+ 4 lanes supporting the following:
+ - PCI Express: supports Gen 1 and Gen 2
+ - SGMII 1G and SGMII 2.5G
+ - QSGMII
+ - XFI
+ - SATA 2.0
+ - High-speed multiplexers route the SerDes traffic to appropriate slots or connectors.
+ - Aurora debug with dedicated connectors.
+- DDR Controller
+ - Supports up to 1600 MTPS data-rate.
+ - Supports one DDR4 or DDR3L module using DDR4 to DDR3L adapter card.
+ - Supports Single-, dual- or quad-rank DIMMs
+ - DDR power supplies 1.35V (DDR3L)/1.20V (DDR4) to all devices with automatic tracking of VTT.
+- IFC/Local Bus
+ - NAND Flash: 8-bit, async, up to 2GB
+ - NOR: 8-bit or 16-bit, non-multiplexed, up to 512MB
+ - NOR devices support 8 virtual banks
+ - Socketed to allow alternate devices
+ - GASIC: Simple (minimal) target within QIXIS FPGA
+ - PromJET rapid memory download support
+ - IFC Debug/Development card
+- Ethernet
+ - Two on-board RGMII 10M/100M/1G ethernet ports.
+ - One QSGMII interface
+ - Four SGMII interface supporting 1Gbps
+ - Three SGMII interfaces supporting 2.5Gbps
+ - one 10Gbps XFI or 10Base-KR interface
+- QIXIS System Logic FPGA
+ - Manages system power and reset sequencing.
+ - Manages the configurations of DUT, board, and clock for dynamic shmoo.
+ - Collects V-I-T data in background for code/power profiling.
+ - Supports legacy TMT test features (POSt, IRS, SYSCLK-synchronous assertion).
+ - General fault monitoring and logging.
+ - Powered from ATX 'standby' power supply that allows continuous operation while rest of the system is off.
+- Clocks
+ - System and DDR clock (SYSCLK, DDRCLK).
+ - Switch selectable to one of 16 common settings in the interval of 64 MHz-166 MHz.
+ - Software programmable in 1 MHz increments from 1-200 MHz.
+ - SERDES clocks
+ - Provides clocks to SerDes blocks and slots.
+ - 100 MHz, 125 MHz and 156.25 MHz options.
+ - Spread-spectrum option for 100 MHz.
+- Power Supplies
+ - Dedicated PMBus regulator for VDD and VDDC.
+ - Adjustable from 0.7V to 1.3V at 35A
+ - VDD can be disabled independanty from VDDC for “deep sleep”.
+ - DDR3L/DDR4 power supply for GVDD: 1.35 or 1.20V at up to 22A.
+ - VTT/MVREF automatically track operating voltage.
+ - Dedicated 2.5V VPP supply.
+ - Dedicated regulators/filters for AVDD supplies.
+ - Dedicated regulators for other supplies, for example OVDD, CVDD, DVDD, LVDD, POVDD, and EVDD.
+- Video
+ - DIU supports video up to 1280x1024x32 bpp.
+ - Chrontel CH7201 for HDMI connection.
+ - TI DS90C387R for direct LCD connection.
+ - Raw (not encoded) video connector for testing or other encoders.
+- USB
+ - Supports two USB 2.0 ports with integrated PHYs.
+ - Two type A ports with 5V@1.5A per port.
+ - Second port can be converted to OTG mini-AB.
+- SDHC
+ For T1024QDS, the SDHC port connects directly to an adapter card slot that has the following features:
+ - upport for optional clock feedback paths.
+ - Support for optional high-speed voltage translation direction controls.
+ - Support for SD slots for: SD, SDHC (1x, 4x, 8x) and MMC.
+ - Support for eMMC memory devices.
+- SPI
+ -On-board support of 3 different devices and sizes.
+- Other IO
+ - Two Serial ports
+ - ProfiBus port
+ - Four I2C ports
+
+
+Memory map on T1024QDS
+----------------------
+Start Address End Address Description Size
+0xF_FFDF_0000 0xF_FFDF_0FFF IFC - FPGA 4KB
+0xF_FF80_0000 0xF_FF80_FFFF IFC - NAND Flash 64KB
+0xF_FE00_0000 0xF_FEFF_FFFF CCSRBAR 16MB
+0xF_F802_0000 0xF_F802_FFFF PCI Express 3 I/O Space 64KB
+0xF_F801_0000 0xF_F801_FFFF PCI Express 2 I/O Space 64KB
+0xF_F800_0000 0xF_F800_FFFF PCI Express 1 I/O Space 64KB
+0xF_F600_0000 0xF_F7FF_FFFF Queue manager software portal 32MB
+0xF_F400_0000 0xF_F5FF_FFFF Buffer manager software portal 32MB
+0xF_E800_0000 0xF_EFFF_FFFF IFC - NOR Flash 128MB
+0xF_E000_0000 0xF_E7FF_FFFF Promjet 128MB
+0xF_0000_0000 0xF_003F_FFFF DCSR 4MB
+0xC_2000_0000 0xC_2FFF_FFFF PCI Express 3 Mem Space 256MB
+0xC_1000_0000 0xC_1FFF_FFFF PCI Express 2 Mem Space 256MB
+0xC_0000_0000 0xC_0FFF_FFFF PCI Express 1 Mem Space 256MB
+0x0_0000_0000 0x0_ffff_ffff DDR 4GB
+
+
+128MB NOR Flash memory Map
+--------------------------
+Start Address End Address Definition Max size
+0xEFF40000 0xEFFFFFFF u-boot (current bank) 768KB
+0xEFF20000 0xEFF3FFFF u-boot env (current bank) 128KB
+0xEFF00000 0xEFF1FFFF FMAN Ucode (current bank) 128KB
+0xEFE00000 0xEFE3FFFF QE firmware (current bank) 256KB
+0xED300000 0xEFEFFFFF rootfs (alt bank) 44MB
+0xEC800000 0xEC8FFFFF Hardware device tree (alt bank) 1MB
+0xEC020000 0xEC7FFFFF Linux.uImage (alt bank) 7MB + 875KB
+0xEC000000 0xEC01FFFF RCW (alt bank) 128KB
+0xEBF40000 0xEBFFFFFF u-boot (alt bank) 768KB
+0xEBF20000 0xEBF3FFFF u-boot env (alt bank) 128KB
+0xEBF00000 0xEBF1FFFF FMAN ucode (alt bank) 128KB
+0xEBE00000 0xEBE3FFFF QE firmware (alt bank) 256KB
+0xE9300000 0xEBEFFFFF rootfs (current bank) 44MB
+0xE8800000 0xE88FFFFF Hardware device tree (cur bank) 1MB
+0xE8020000 0xE86FFFFF Linux.uImage (current bank) 7MB + 875KB
+0xE8000000 0xE801FFFF RCW (current bank) 128KB
+
+
+SerDes clock vs DIP-switch settings
+-----------------------------------
+SRDS_PRTCL_S1 SD1_REF_CLK1 SD1_REF_CLK2 SW4[1:4]
+0x6F 100MHz 125MHz 1101
+0xD6 100MHz 100MHz 1111
+0x99 156.25MHz 100MHz 1011
+
+
+T1024 Clock frequency
+----------------------
+BIN Core DDR Platform FMan
+Bin1: 1400MHz 1600MT/s 400MHz 700MHz
+Bin2: 1200MHz 1600MT/s 400MHz 600MHz
+Bin3: 1000MHz 1600MT/s 400MHz 500MHz
+
+
+
+Software configurations and board settings
+------------------------------------------
+1. NOR boot:
+ a. build NOR boot image
+ $ make T1024QDS_defconfig (For DDR3L, by default)
+ or make T1024QDS_D4_defconfig (For DDR4)
+ $ make
+ b. program u-boot.bin image to NOR flash
+ => tftp 1000000 u-boot.bin
+ => pro off all;era eff40000 efffffff;cp.b 1000000 eff40000 $filesize
+ set SW1[1:8] = '00010011', SW2[1] = '1', SW6[1:4] = '0000' for NOR boot
+
+ Switching between default bank0 and alternate bank4 on NOR flash
+ To change boot source to vbank4:
+ via software: run command 'qixis_reset altbank' in u-boot.
+ via DIP-switch: set SW6[1:4] = '0100'
+
+ To change boot source to vbank0:
+ via software: run command 'qixis_reset' in u-boot.
+ via DIP-Switch: set SW6[1:4] = '0000'
+
+2. NAND Boot:
+ a. build PBL image for NAND boot
+ $ make T1024QDS_NAND_defconfig
+ $ make
+ b. program u-boot-with-spl-pbl.bin to NAND flash
+ => tftp 1000000 u-boot-with-spl-pbl.bin
+ => nand erase 0 $filesize
+ => nand write 1000000 0 $filesize
+ set SW1[1:8] = '10000010', SW2[1] = '0' and SW6[1:4] = '1001' for NAND boot
+
+3. SPI Boot:
+ a. build PBL image for SPI boot
+ $ make T1024QDS_SPIFLASH_defconfig
+ $ make
+ b. program u-boot-with-spl-pbl.bin to SPI flash
+ => tftp 1000000 u-boot-with-spl-pbl.bin
+ => sf probe 0
+ => sf erase 0 f0000
+ => sf write 1000000 0 $filesize
+ set SW1[1:8] = '00100010', SW2[1] ='1' for SPI boot
+
+4. SD Boot:
+ a. build PBL image for SD boot
+ $ make T1024QDS_SDCARD_defconfig
+ $ make
+ b. program u-boot-with-spl-pbl.bin to SD/MMC card
+ => tftp 1000000 u-boot-with-spl-pbl.bin
+ => mmc write 1000000 8 0x800
+ => tftp 1000000 fsl_fman_ucode_t1024_xx.bin
+ => mmc write 1000000 0x820 80
+ set SW1[1:8] = '00100000', SW2[1] = '0' for SD boot
+
+
+DIU/QE-TDM/SDXC settings
+-------------------
+a) For TDM Riser: set pin_mux=tdm in hwconfig
+b) For UCC(ProfiBus): set pin_mux=ucc in hwconfig
+c) For HDMI(DVI): set pin_mux=hdmi in hwconfig
+d) For LCD(DFP): set pin_mux=lcd in hwconfig
+e) For SDXC: set adaptor=sdxc in hwconfig
+
+2-stage NAND/SPI/SD boot loader
+-------------------------------
+PBL initializes the internal CPC-SRAM and copy SPL(160K) to SRAM.
+SPL further initializes DDR using SPD and environment variables
+and copy u-boot(768 KB) from NAND/SPI/SD device to DDR.
+Finally SPL transers control to u-boot for futher booting.
+
+SPL has following features:
+ - Executes within 256K
+ - No relocation required
+
+Run time view of SPL framework
+-------------------------------------------------
+|Area | Address |
+-------------------------------------------------
+|SecureBoot header | 0xFFFC0000 (32KB) |
+-------------------------------------------------
+|GD, BD | 0xFFFC8000 (4KB) |
+-------------------------------------------------
+|ENV | 0xFFFC9000 (8KB) |
+-------------------------------------------------
+|HEAP | 0xFFFCB000 (30KB) |
+-------------------------------------------------
+|STACK | 0xFFFD8000 (22KB) |
+-------------------------------------------------
+|U-boot SPL | 0xFFFD8000 (160KB) |
+-------------------------------------------------
+
+NAND Flash memory Map on T1024QDS
+-------------------------------------------------------------
+Start End Definition Size
+0x000000 0x0FFFFF u-boot 1MB
+0x100000 0x15FFFF u-boot env 8KB
+0x160000 0x17FFFF FMAN Ucode 128KB
+0x180000 0x19FFFF QE Firmware 128KB
+
+
+SD Card memory Map on T1024QDS
+----------------------------------------------------
+Block #blocks Definition Size
+0x008 2048 u-boot img 1MB
+0x800 0016 u-boot env 8KB
+0x820 0256 FMAN Ucode 128KB
+0x920 0256 QE Firmware 128KB
+
+
+SPI Flash memory Map on T1024QDS
+----------------------------------------------------
+Start End Definition Size
+0x000000 0x0FFFFF u-boot img 1MB
+0x100000 0x101FFF u-boot env 8KB
+0x110000 0x12FFFF FMAN Ucode 128KB
+0x130000 0x14FFFF QE Firmware 128KB
+
+
+For more details, please refer to T1024QDS Reference Manual and access
+website www.freescale.com and Freescale QorIQ SDK Infocenter document.
diff --git a/board/freescale/t102xqds/ddr.c b/board/freescale/t102xqds/ddr.c
new file mode 100644
index 0000000..46fc64e
--- /dev/null
+++ b/board/freescale/t102xqds/ddr.c
@@ -0,0 +1,170 @@
+/*
+ * Copyright 2014 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <i2c.h>
+#include <hwconfig.h>
+#include <asm/mmu.h>
+#include <fsl_ddr_sdram.h>
+#include <fsl_ddr_dimm_params.h>
+#include <asm/fsl_law.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+struct board_specific_parameters {
+ u32 n_ranks;
+ u32 datarate_mhz_high;
+ u32 rank_gb;
+ u32 clk_adjust;
+ u32 wrlvl_start;
+ u32 wrlvl_ctl_2;
+ u32 wrlvl_ctl_3;
+};
+
+/*
+ * datarate_mhz_high values need to be in ascending order
+ */
+static const struct board_specific_parameters udimm0[] = {
+ /*
+ * memory controller 0
+ * num| hi| rank| clk| wrlvl | wrlvl | wrlvl |
+ * ranks| mhz| GB |adjst| start | ctl2 | ctl3 |
+ */
+#if defined(CONFIG_SYS_FSL_DDR4)
+ {2, 1666, 0, 4, 7, 0x0808090B, 0x0C0D0E0A,},
+ {2, 1900, 0, 4, 6, 0x08080A0C, 0x0D0E0F0A,},
+ {1, 1666, 0, 4, 6, 0x0708090B, 0x0C0D0E09,},
+ {1, 1900, 0, 4, 6, 0x08080A0C, 0x0D0E0F0A,},
+ {1, 2200, 0, 4, 7, 0x08090A0D, 0x0F0F100C,},
+#elif defined(CONFIG_SYS_FSL_DDR3)
+ {2, 833, 0, 4, 6, 0x06060607, 0x08080807,},
+ {2, 1350, 0, 4, 7, 0x0708080A, 0x0A0B0C09,},
+ {2, 1666, 0, 4, 7, 0x0808090B, 0x0C0D0E0A,},
+ {1, 833, 0, 4, 6, 0x06060607, 0x08080807,},
+ {1, 1350, 0, 4, 7, 0x0708080A, 0x0A0B0C09,},
+ {1, 1666, 0, 4, 7, 0x0808090B, 0x0C0D0E0A,},
+#else
+#error DDR type not defined
+#endif
+ {}
+};
+
+static const struct board_specific_parameters *udimms[] = {
+ udimm0,
+};
+
+void fsl_ddr_board_options(memctl_options_t *popts,
+ dimm_params_t *pdimm,
+ unsigned int ctrl_num)
+{
+ const struct board_specific_parameters *pbsp, *pbsp_highest = NULL;
+ ulong ddr_freq;
+ struct cpu_type *cpu = gd->arch.cpu;
+
+ if (ctrl_num > 2) {
+ printf("Not supported controller number %d\n", ctrl_num);
+ return;
+ }
+ if (!pdimm->n_ranks)
+ return;
+
+ pbsp = udimms[0];
+
+ /* Get clk_adjust according to the board ddr freqency and n_banks
+ * specified in board_specific_parameters table.
+ */
+ ddr_freq = get_ddr_freq(0) / 1000000;
+ while (pbsp->datarate_mhz_high) {
+ if (pbsp->n_ranks == pdimm->n_ranks &&
+ (pdimm->rank_density >> 30) >= pbsp->rank_gb) {
+ if (ddr_freq <= pbsp->datarate_mhz_high) {
+ popts->clk_adjust = pbsp->clk_adjust;
+ popts->wrlvl_start = pbsp->wrlvl_start;
+ popts->wrlvl_ctl_2 = pbsp->wrlvl_ctl_2;
+ popts->wrlvl_ctl_3 = pbsp->wrlvl_ctl_3;
+ goto found;
+ }
+ pbsp_highest = pbsp;
+ }
+ pbsp++;
+ }
+
+ if (pbsp_highest) {
+ printf("Error: board specific timing not found\n");
+ printf("for data rate %lu MT/s\n", ddr_freq);
+ printf("Trying to use the highest speed (%u) parameters\n",
+ pbsp_highest->datarate_mhz_high);
+ popts->clk_adjust = pbsp_highest->clk_adjust;
+ popts->wrlvl_start = pbsp_highest->wrlvl_start;
+ popts->wrlvl_ctl_2 = pbsp->wrlvl_ctl_2;
+ popts->wrlvl_ctl_3 = pbsp->wrlvl_ctl_3;
+ } else {
+ panic("DIMM is not supported by this board");
+ }
+found:
+ debug("Found timing match: n_ranks %d, data rate %d, rank_gb %d\n",
+ pbsp->n_ranks, pbsp->datarate_mhz_high, pbsp->rank_gb);
+ debug("\tclk_adjust %d, wrlvl_start %d, wrlvl_ctrl_2 0x%x, ",
+ pbsp->clk_adjust, pbsp->wrlvl_start, pbsp->wrlvl_ctl_2);
+ debug("wrlvl_ctrl_3 0x%x\n", pbsp->wrlvl_ctl_3);
+
+ /*
+ * Factors to consider for half-strength driver enable:
+ * - number of DIMMs installed
+ */
+ popts->half_strength_driver_enable = 1;
+ /*
+ * Write leveling override
+ */
+ popts->wrlvl_override = 1;
+ popts->wrlvl_sample = 0xf;
+
+ /*
+ * rtt and rtt_wr override
+ */
+ popts->rtt_override = 0;
+
+ /* Enable ZQ calibration */
+ popts->zq_en = 1;
+
+ /* DHC_EN =1, ODT = 75 Ohm */
+#ifdef CONFIG_SYS_FSL_DDR4
+ popts->ddr_cdr1 = DDR_CDR1_DHC_EN | DDR_CDR1_ODT(DDR_CDR_ODT_80ohm);
+ popts->ddr_cdr2 = DDR_CDR2_ODT(DDR_CDR_ODT_80ohm) |
+ DDR_CDR2_VREF_OVRD(70); /* Vref = 70% */
+#else
+ popts->ddr_cdr1 = DDR_CDR1_DHC_EN | DDR_CDR1_ODT(DDR_CDR_ODT_75ohm);
+ popts->ddr_cdr2 = DDR_CDR2_ODT(DDR_CDR_ODT_75ohm);
+#endif
+
+ /* T1023 supports max DDR bus 32bit width, T1024 supports DDR 64bit,
+ * set DDR bus width to 32bit for T1023
+ */
+ if (cpu->soc_ver == SVR_T1023)
+ popts->data_bus_width = DDR_DATA_BUS_WIDTH_32;
+
+#ifdef CONFIG_FORCE_DDR_DATA_BUS_WIDTH_32
+ /* for DDR bus 32bit test on T1024 */
+ popts->data_bus_width = DDR_DATA_BUS_WIDTH_32;
+#endif
+}
+
+phys_size_t initdram(int board_type)
+{
+ phys_size_t dram_size;
+
+#if defined(CONFIG_SPL_BUILD) || !defined(CONFIG_RAMBOOT_PBL)
+ puts("Initializing....using SPD\n");
+
+ dram_size = fsl_ddr_sdram();
+ dram_size = setup_ddr_tlbs(dram_size / 0x100000);
+ dram_size *= 0x100000;
+#else
+ /* DDR has been initialised by first stage boot loader */
+ dram_size = fsl_ddr_sdram_size();
+#endif
+ return dram_size;
+}
diff --git a/board/freescale/t102xqds/eth_t102xqds.c b/board/freescale/t102xqds/eth_t102xqds.c
new file mode 100644
index 0000000..7723f58
--- /dev/null
+++ b/board/freescale/t102xqds/eth_t102xqds.c
@@ -0,0 +1,442 @@
+/*
+ * Copyright 2014 Freescale Semiconductor, Inc.
+ *
+ * Shengzhou Liu <Shengzhou.Liu@freescale.com>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <command.h>
+#include <netdev.h>
+#include <asm/mmu.h>
+#include <asm/processor.h>
+#include <asm/immap_85xx.h>
+#include <asm/fsl_law.h>
+#include <asm/fsl_serdes.h>
+#include <asm/fsl_portals.h>
+#include <asm/fsl_liodn.h>
+#include <malloc.h>
+#include <fm_eth.h>
+#include <fsl_mdio.h>
+#include <miiphy.h>
+#include <phy.h>
+#include <asm/fsl_dtsec.h>
+#include <asm/fsl_serdes.h>
+#include "../common/qixis.h"
+#include "../common/fman.h"
+#include "t102xqds_qixis.h"
+
+#define EMI_NONE 0xFFFFFFFF
+#define EMI1_RGMII1 0
+#define EMI1_RGMII2 1
+#define EMI1_SLOT1 2
+#define EMI1_SLOT2 3
+#define EMI1_SLOT3 4
+#define EMI1_SLOT4 5
+#define EMI1_SLOT5 6
+#define EMI2 7
+
+static int mdio_mux[NUM_FM_PORTS];
+
+static const char * const mdio_names[] = {
+ "T1024QDS_MDIO_RGMII1",
+ "T1024QDS_MDIO_RGMII2",
+ "T1024QDS_MDIO_SLOT1",
+ "T1024QDS_MDIO_SLOT2",
+ "T1024QDS_MDIO_SLOT3",
+ "T1024QDS_MDIO_SLOT4",
+ "T1024QDS_MDIO_SLOT5",
+ "T1024QDS_MDIO_10GC",
+ "NULL",
+};
+
+/* Map SerDes1 4 lanes to default slot, will be initialized dynamically */
+static u8 lane_to_slot[] = {2, 3, 4, 5};
+
+static const char *t1024qds_mdio_name_for_muxval(u8 muxval)
+{
+ return mdio_names[muxval];
+}
+
+struct mii_dev *mii_dev_for_muxval(u8 muxval)
+{
+ struct mii_dev *bus;
+ const char *name;
+
+ if (muxval > EMI2)
+ return NULL;
+
+ name = t1024qds_mdio_name_for_muxval(muxval);
+
+ if (!name) {
+ printf("No bus for muxval %x\n", muxval);
+ return NULL;
+ }
+
+ bus = miiphy_get_dev_by_name(name);
+
+ if (!bus) {
+ printf("No bus by name %s\n", name);
+ return NULL;
+ }
+
+ return bus;
+}
+
+struct t1024qds_mdio {
+ u8 muxval;
+ struct mii_dev *realbus;
+};
+
+static void t1024qds_mux_mdio(u8 muxval)
+{
+ u8 brdcfg4;
+
+ if (muxval < 7) {
+ brdcfg4 = QIXIS_READ(brdcfg[4]);
+ brdcfg4 &= ~BRDCFG4_EMISEL_MASK;
+ brdcfg4 |= (muxval << BRDCFG4_EMISEL_SHIFT);
+ QIXIS_WRITE(brdcfg[4], brdcfg4);
+ }
+}
+
+static int t1024qds_mdio_read(struct mii_dev *bus, int addr, int devad,
+ int regnum)
+{
+ struct t1024qds_mdio *priv = bus->priv;
+
+ t1024qds_mux_mdio(priv->muxval);
+
+ return priv->realbus->read(priv->realbus, addr, devad, regnum);
+}
+
+static int t1024qds_mdio_write(struct mii_dev *bus, int addr, int devad,
+ int regnum, u16 value)
+{
+ struct t1024qds_mdio *priv = bus->priv;
+
+ t1024qds_mux_mdio(priv->muxval);
+
+ return priv->realbus->write(priv->realbus, addr, devad, regnum, value);
+}
+
+static int t1024qds_mdio_reset(struct mii_dev *bus)
+{
+ struct t1024qds_mdio *priv = bus->priv;
+
+ return priv->realbus->reset(priv->realbus);
+}
+
+static int t1024qds_mdio_init(char *realbusname, u8 muxval)
+{
+ struct t1024qds_mdio *pmdio;
+ struct mii_dev *bus = mdio_alloc();
+
+ if (!bus) {
+ printf("Failed to allocate t1024qds MDIO bus\n");
+ return -1;
+ }
+
+ pmdio = malloc(sizeof(*pmdio));
+ if (!pmdio) {
+ printf("Failed to allocate t1024qds private data\n");
+ free(bus);
+ return -1;
+ }
+
+ bus->read = t1024qds_mdio_read;
+ bus->write = t1024qds_mdio_write;
+ bus->reset = t1024qds_mdio_reset;
+ sprintf(bus->name, t1024qds_mdio_name_for_muxval(muxval));
+
+ pmdio->realbus = miiphy_get_dev_by_name(realbusname);
+
+ if (!pmdio->realbus) {
+ printf("No bus with name %s\n", realbusname);
+ free(bus);
+ free(pmdio);
+ return -1;
+ }
+
+ pmdio->muxval = muxval;
+ bus->priv = pmdio;
+ return mdio_register(bus);
+}
+
+void board_ft_fman_fixup_port(void *fdt, char *compat, phys_addr_t addr,
+ enum fm_port port, int offset)
+{
+ struct fixed_link f_link;
+
+ if (fm_info_get_enet_if(port) == PHY_INTERFACE_MODE_RGMII) {
+ if (port == FM1_DTSEC3) {
+ fdt_set_phy_handle(fdt, compat, addr, "rgmii_phy2");
+ fdt_setprop(fdt, offset, "phy-connection-type",
+ "rgmii", 5);
+ fdt_status_okay_by_alias(fdt, "emi1_rgmii1");
+ }
+ } else if (fm_info_get_enet_if(port) == PHY_INTERFACE_MODE_SGMII) {
+ if (port == FM1_DTSEC1) {
+ fdt_set_phy_handle(fdt, compat, addr,
+ "sgmii_vsc8234_phy_s5");
+ } else if (port == FM1_DTSEC2) {
+ fdt_set_phy_handle(fdt, compat, addr,
+ "sgmii_vsc8234_phy_s4");
+ }
+ } else if (fm_info_get_enet_if(port) == PHY_INTERFACE_MODE_SGMII_2500) {
+ if (port == FM1_DTSEC3) {
+ fdt_set_phy_handle(fdt, compat, addr,
+ "sgmii_aqr105_phy_s3");
+ }
+ } else if (fm_info_get_enet_if(port) == PHY_INTERFACE_MODE_QSGMII) {
+ switch (port) {
+ case FM1_DTSEC1:
+ fdt_set_phy_handle(fdt, compat, addr, "qsgmii_phy_p1");
+ break;
+ case FM1_DTSEC2:
+ fdt_set_phy_handle(fdt, compat, addr, "qsgmii_phy_p2");
+ break;
+ case FM1_DTSEC3:
+ fdt_set_phy_handle(fdt, compat, addr, "qsgmii_phy_p3");
+ break;
+ case FM1_DTSEC4:
+ fdt_set_phy_handle(fdt, compat, addr, "qsgmii_phy_p4");
+ break;
+ default:
+ break;
+ }
+ fdt_delprop(fdt, offset, "phy-connection-type");
+ fdt_setprop(fdt, offset, "phy-connection-type", "qsgmii", 6);
+ fdt_status_okay_by_alias(fdt, "emi1_slot2");
+ } else if (fm_info_get_enet_if(port) == PHY_INTERFACE_MODE_XGMII) {
+ /* XFI interface */
+ f_link.phy_id = port;
+ f_link.duplex = 1;
+ f_link.link_speed = 10000;
+ f_link.pause = 0;
+ f_link.asym_pause = 0;
+ /* no PHY for XFI */
+ fdt_delprop(fdt, offset, "phy-handle");
+ fdt_setprop(fdt, offset, "fixed-link", &f_link, sizeof(f_link));
+ fdt_setprop(fdt, offset, "phy-connection-type", "xgmii", 5);
+ }
+}
+
+void fdt_fixup_board_enet(void *fdt)
+{
+}
+
+/*
+ * This function reads RCW to check if Serdes1{A:D} is configured
+ * to slot 1/2/3/4/5 and update the lane_to_slot[] array accordingly
+ */
+static void initialize_lane_to_slot(void)
+{
+ ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
+ u32 srds_s1 = in_be32(&gur->rcwsr[4]) &
+ FSL_CORENET2_RCWSR4_SRDS1_PRTCL;
+
+ srds_s1 >>= FSL_CORENET2_RCWSR4_SRDS1_PRTCL_SHIFT;
+
+ switch (srds_s1) {
+ case 0x46:
+ case 0x47:
+ lane_to_slot[1] = 2;
+ break;
+ default:
+ break;
+ }
+}
+
+int board_eth_init(bd_t *bis)
+{
+#if defined(CONFIG_FMAN_ENET)
+ int i, idx, lane, slot, interface;
+ struct memac_mdio_info dtsec_mdio_info;
+ struct memac_mdio_info tgec_mdio_info;
+ ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
+ u32 srds_s1;
+
+ srds_s1 = in_be32(&gur->rcwsr[4]) &
+ FSL_CORENET2_RCWSR4_SRDS1_PRTCL;
+ srds_s1 >>= FSL_CORENET2_RCWSR4_SRDS1_PRTCL_SHIFT;
+
+ initialize_lane_to_slot();
+
+ /* Initialize the mdio_mux array so we can recognize empty elements */
+ for (i = 0; i < NUM_FM_PORTS; i++)
+ mdio_mux[i] = EMI_NONE;
+
+ dtsec_mdio_info.regs =
+ (struct memac_mdio_controller *)CONFIG_SYS_FM1_DTSEC_MDIO_ADDR;
+
+ dtsec_mdio_info.name = DEFAULT_FM_MDIO_NAME;
+
+ /* Register the 1G MDIO bus */
+ fm_memac_mdio_init(bis, &dtsec_mdio_info);
+
+ tgec_mdio_info.regs =
+ (struct memac_mdio_controller *)CONFIG_SYS_FM1_TGEC_MDIO_ADDR;
+ tgec_mdio_info.name = DEFAULT_FM_TGEC_MDIO_NAME;
+
+ /* Register the 10G MDIO bus */
+ fm_memac_mdio_init(bis, &tgec_mdio_info);
+
+ /* Register the muxing front-ends to the MDIO buses */
+ t1024qds_mdio_init(DEFAULT_FM_MDIO_NAME, EMI1_RGMII1);
+ t1024qds_mdio_init(DEFAULT_FM_MDIO_NAME, EMI1_RGMII2);
+ t1024qds_mdio_init(DEFAULT_FM_MDIO_NAME, EMI1_SLOT1);
+ t1024qds_mdio_init(DEFAULT_FM_MDIO_NAME, EMI1_SLOT2);
+ t1024qds_mdio_init(DEFAULT_FM_MDIO_NAME, EMI1_SLOT3);
+ t1024qds_mdio_init(DEFAULT_FM_MDIO_NAME, EMI1_SLOT4);
+ t1024qds_mdio_init(DEFAULT_FM_MDIO_NAME, EMI1_SLOT5);
+ t1024qds_mdio_init(DEFAULT_FM_TGEC_MDIO_NAME, EMI2);
+
+ /* Set the two on-board RGMII PHY address */
+ fm_info_set_phy_address(FM1_DTSEC3, RGMII_PHY2_ADDR);
+ fm_info_set_phy_address(FM1_DTSEC4, RGMII_PHY1_ADDR);
+
+ switch (srds_s1) {
+ case 0xd5:
+ case 0xd6:
+ /* QSGMII in Slot2 */
+ fm_info_set_phy_address(FM1_DTSEC1, 0x8);
+ fm_info_set_phy_address(FM1_DTSEC2, 0x9);
+ fm_info_set_phy_address(FM1_DTSEC3, 0xa);
+ fm_info_set_phy_address(FM1_DTSEC4, 0xb);
+ break;
+ case 0x95:
+ case 0x99:
+ /*
+ * XFI does not need a PHY to work, but to avoid U-boot use
+ * default PHY address which is zero to a MAC when it found
+ * a MAC has no PHY address, we give a PHY address to XFI
+ * MAC, and should not use a real XAUI PHY address, since
+ * MDIO can access it successfully, and then MDIO thinks the
+ * XAUI card is used for the XFI MAC, which will cause error.
+ */
+ fm_info_set_phy_address(FM1_10GEC1, 4);
+ fm_info_set_phy_address(FM1_DTSEC2, SGMII_CARD_PORT1_PHY_ADDR);
+ break;
+ case 0x6f:
+ /* SGMII in Slot3, Slot4, Slot5 */
+ fm_info_set_phy_address(FM1_DTSEC1, SGMII_CARD_AQ_PHY_ADDR_S5);
+ fm_info_set_phy_address(FM1_DTSEC2, SGMII_CARD_AQ_PHY_ADDR_S4);
+ fm_info_set_phy_address(FM1_DTSEC3, SGMII_CARD_PORT1_PHY_ADDR);
+ break;
+ case 0x7f:
+ fm_info_set_phy_address(FM1_DTSEC1, SGMII_CARD_AQ_PHY_ADDR_S5);
+ fm_info_set_phy_address(FM1_DTSEC2, SGMII_CARD_AQ_PHY_ADDR_S4);
+ fm_info_set_phy_address(FM1_DTSEC3, SGMII_CARD_AQ_PHY_ADDR_S3);
+ break;
+ case 0x47:
+ fm_info_set_phy_address(FM1_DTSEC1, SGMII_CARD_PORT1_PHY_ADDR);
+ break;
+ case 0x77:
+ fm_info_set_phy_address(FM1_DTSEC1, SGMII_CARD_PORT1_PHY_ADDR);
+ fm_info_set_phy_address(FM1_DTSEC3, SGMII_CARD_AQ_PHY_ADDR_S3);
+ break;
+ case 0x5a:
+ fm_info_set_phy_address(FM1_DTSEC2, SGMII_CARD_PORT1_PHY_ADDR);
+ break;
+ case 0x6a:
+ fm_info_set_phy_address(FM1_DTSEC2, SGMII_CARD_PORT1_PHY_ADDR);
+ fm_info_set_phy_address(FM1_DTSEC3, SGMII_CARD_PORT1_PHY_ADDR);
+ break;
+ case 0x5b:
+ fm_info_set_phy_address(FM1_DTSEC1, SGMII_CARD_PORT1_PHY_ADDR);
+ fm_info_set_phy_address(FM1_DTSEC2, SGMII_CARD_PORT1_PHY_ADDR);
+ break;
+ case 0x6b:
+ fm_info_set_phy_address(FM1_DTSEC1, SGMII_CARD_PORT1_PHY_ADDR);
+ fm_info_set_phy_address(FM1_DTSEC2, SGMII_CARD_PORT1_PHY_ADDR);
+ fm_info_set_phy_address(FM1_DTSEC3, SGMII_CARD_PORT1_PHY_ADDR);
+ break;
+ default:
+ break;
+ }
+
+ for (i = FM1_DTSEC1; i < FM1_DTSEC1 + CONFIG_SYS_NUM_FM1_DTSEC; i++) {
+ idx = i - FM1_DTSEC1;
+ interface = fm_info_get_enet_if(i);
+ switch (interface) {
+ case PHY_INTERFACE_MODE_SGMII:
+ case PHY_INTERFACE_MODE_SGMII_2500:
+ case PHY_INTERFACE_MODE_QSGMII:
+ if (interface == PHY_INTERFACE_MODE_SGMII) {
+ lane = serdes_get_first_lane(FSL_SRDS_1,
+ SGMII_FM1_DTSEC1 + idx);
+ } else if (interface == PHY_INTERFACE_MODE_SGMII_2500) {
+ lane = serdes_get_first_lane(FSL_SRDS_1,
+ SGMII_2500_FM1_DTSEC1 + idx);
+ } else {
+ lane = serdes_get_first_lane(FSL_SRDS_1,
+ QSGMII_FM1_A);
+ }
+
+ if (lane < 0)
+ break;
+
+ slot = lane_to_slot[lane];
+ debug("FM1@DTSEC%u expects SGMII in slot %u\n",
+ idx + 1, slot);
+ if (QIXIS_READ(present2) & (1 << (slot - 1)))
+ fm_disable_port(i);
+
+ switch (slot) {
+ case 2:
+ mdio_mux[i] = EMI1_SLOT2;
+ fm_info_set_mdio(i, mii_dev_for_muxval(
+ mdio_mux[i]));
+ break;
+ case 3:
+ mdio_mux[i] = EMI1_SLOT3;
+ fm_info_set_mdio(i, mii_dev_for_muxval(
+ mdio_mux[i]));
+ break;
+ case 4:
+ mdio_mux[i] = EMI1_SLOT4;
+ fm_info_set_mdio(i, mii_dev_for_muxval(
+ mdio_mux[i]));
+ break;
+ case 5:
+ mdio_mux[i] = EMI1_SLOT5;
+ fm_info_set_mdio(i, mii_dev_for_muxval(
+ mdio_mux[i]));
+ break;
+ }
+ break;
+ case PHY_INTERFACE_MODE_RGMII:
+ if (i == FM1_DTSEC3)
+ mdio_mux[i] = EMI1_RGMII2;
+ else if (i == FM1_DTSEC4)
+ mdio_mux[i] = EMI1_RGMII1;
+ fm_info_set_mdio(i, mii_dev_for_muxval(mdio_mux[i]));
+ break;
+ default:
+ break;
+ }
+ }
+
+ for (i = FM1_10GEC1; i < FM1_10GEC1 + CONFIG_SYS_NUM_FM1_10GEC; i++) {
+ idx = i - FM1_10GEC1;
+ switch (fm_info_get_enet_if(i)) {
+ case PHY_INTERFACE_MODE_XGMII:
+ lane = serdes_get_first_lane(FSL_SRDS_1,
+ XFI_FM1_MAC1 + idx);
+ if (lane < 0)
+ break;
+ mdio_mux[i] = EMI2;
+ fm_info_set_mdio(i, mii_dev_for_muxval(mdio_mux[i]));
+ break;
+ default:
+ break;
+ }
+ }
+
+ cpu_eth_init(bis);
+#endif /* CONFIG_FMAN_ENET */
+
+ return pci_eth_init(bis);
+}
diff --git a/board/freescale/t102xqds/law.c b/board/freescale/t102xqds/law.c
new file mode 100644
index 0000000..b1c9d01
--- /dev/null
+++ b/board/freescale/t102xqds/law.c
@@ -0,0 +1,32 @@
+/*
+ * Copyright 2014 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <asm/fsl_law.h>
+#include <asm/mmu.h>
+
+struct law_entry law_table[] = {
+#ifndef CONFIG_SYS_NO_FLASH
+ SET_LAW(CONFIG_SYS_FLASH_BASE_PHYS, LAW_SIZE_256M, LAW_TRGT_IF_IFC),
+#endif
+#ifdef CONFIG_SYS_BMAN_MEM_PHYS
+ SET_LAW(CONFIG_SYS_BMAN_MEM_PHYS, LAW_SIZE_32M, LAW_TRGT_IF_BMAN),
+#endif
+#ifdef CONFIG_SYS_QMAN_MEM_PHYS
+ SET_LAW(CONFIG_SYS_QMAN_MEM_PHYS, LAW_SIZE_32M, LAW_TRGT_IF_QMAN),
+#endif
+#ifdef QIXIS_BASE_PHYS
+ SET_LAW(QIXIS_BASE_PHYS, LAW_SIZE_4K, LAW_TRGT_IF_IFC),
+#endif
+#ifdef CONFIG_SYS_DCSRBAR_PHYS
+ SET_LAW(CONFIG_SYS_DCSRBAR_PHYS, LAW_SIZE_4M, LAW_TRGT_IF_DCSR),
+#endif
+#ifdef CONFIG_SYS_NAND_BASE_PHYS
+ SET_LAW(CONFIG_SYS_NAND_BASE_PHYS, LAW_SIZE_64K, LAW_TRGT_IF_IFC),
+#endif
+};
+
+int num_law_entries = ARRAY_SIZE(law_table);
diff --git a/board/freescale/t102xqds/pci.c b/board/freescale/t102xqds/pci.c
new file mode 100644
index 0000000..7369289
--- /dev/null
+++ b/board/freescale/t102xqds/pci.c
@@ -0,0 +1,23 @@
+/*
+ * Copyright 2014 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <command.h>
+#include <pci.h>
+#include <asm/fsl_pci.h>
+#include <libfdt.h>
+#include <fdt_support.h>
+#include <asm/fsl_serdes.h>
+
+void pci_init_board(void)
+{
+ fsl_pcie_init_board(0);
+}
+
+void pci_of_setup(void *blob, bd_t *bd)
+{
+ FT_FSL_PCI_SETUP;
+}
diff --git a/board/freescale/t102xqds/spl.c b/board/freescale/t102xqds/spl.c
new file mode 100644
index 0000000..08aef6e
--- /dev/null
+++ b/board/freescale/t102xqds/spl.c
@@ -0,0 +1,151 @@
+/* Copyright 2014 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <malloc.h>
+#include <ns16550.h>
+#include <nand.h>
+#include <i2c.h>
+#include <mmc.h>
+#include <fsl_esdhc.h>
+#include <spi_flash.h>
+#include "../common/qixis.h"
+#include "t102xqds_qixis.h"
+
+DECLARE_GLOBAL_DATA_PTR;
+
+phys_size_t get_effective_memsize(void)
+{
+ return CONFIG_SYS_L3_SIZE;
+}
+
+unsigned long get_board_sys_clk(void)
+{
+ u8 sysclk_conf = QIXIS_READ(brdcfg[1]);
+
+ switch (sysclk_conf & 0x0F) {
+ case QIXIS_SYSCLK_83:
+ return 83333333;
+ case QIXIS_SYSCLK_100:
+ return 100000000;
+ case QIXIS_SYSCLK_125:
+ return 125000000;
+ case QIXIS_SYSCLK_133:
+ return 133333333;
+ case QIXIS_SYSCLK_150:
+ return 150000000;
+ case QIXIS_SYSCLK_160:
+ return 160000000;
+ case QIXIS_SYSCLK_166:
+ return 166666666;
+ }
+ return 66666666;
+}
+
+unsigned long get_board_ddr_clk(void)
+{
+ u8 ddrclk_conf = QIXIS_READ(brdcfg[1]);
+
+ switch ((ddrclk_conf & 0x30) >> 4) {
+ case QIXIS_DDRCLK_100:
+ return 100000000;
+ case QIXIS_DDRCLK_125:
+ return 125000000;
+ case QIXIS_DDRCLK_133:
+ return 133333333;
+ }
+ return 66666666;
+}
+
+void board_init_f(ulong bootflag)
+{
+ u32 plat_ratio, sys_clk, ccb_clk;
+ ccsr_gur_t *gur = (void *)CONFIG_SYS_MPC85xx_GUTS_ADDR;
+
+#if defined(CONFIG_PPC_T1040) && defined(CONFIG_SPL_NAND_BOOT)
+ /*
+ * There is T1040 SoC issue where NOR, FPGA are inaccessible during
+ * NAND boot because IFC signals > IFC_AD7 are not enabled.
+ * This workaround changes RCW source to make all signals enabled.
+ */
+ u32 porsr1, pinctl;
+#define FSL_CORENET_CCSR_PORSR1_RCW_MASK 0xFF800000
+
+ porsr1 = in_be32(&gur->porsr1);
+ pinctl = ((porsr1 & ~(FSL_CORENET_CCSR_PORSR1_RCW_MASK)) | 0x24800000);
+ out_be32((unsigned int *)(CONFIG_SYS_DCSRBAR + 0x20000), pinctl);
+#endif
+
+ /* Memcpy existing GD at CONFIG_SPL_GD_ADDR */
+ memcpy((void *)CONFIG_SPL_GD_ADDR, (void *)gd, sizeof(gd_t));
+
+ /* Update GD pointer */
+ gd = (gd_t *)(CONFIG_SPL_GD_ADDR);
+
+ console_init_f();
+
+ /* initialize selected port with appropriate baud rate */
+ sys_clk = get_board_sys_clk();
+ plat_ratio = (in_be32(&gur->rcwsr[0]) >> 25) & 0x1f;
+ ccb_clk = sys_clk * plat_ratio / 2;
+
+ NS16550_init((NS16550_t)CONFIG_SYS_NS16550_COM1,
+ ccb_clk / 16 / CONFIG_BAUDRATE);
+
+#if defined(CONFIG_SPL_MMC_BOOT)
+ puts("\nSD boot...\n");
+#elif defined(CONFIG_SPL_SPI_BOOT)
+ puts("\nSPI boot...\n");
+#elif defined(CONFIG_SPL_NAND_BOOT)
+ puts("\nNAND boot...\n");
+#endif
+
+ relocate_code(CONFIG_SPL_RELOC_STACK, (gd_t *)CONFIG_SPL_GD_ADDR, 0x0);
+}
+
+void board_init_r(gd_t *gd, ulong dest_addr)
+{
+ bd_t *bd;
+
+ bd = (bd_t *)(gd + sizeof(gd_t));
+ memset(bd, 0, sizeof(bd_t));
+ gd->bd = bd;
+ bd->bi_memstart = CONFIG_SYS_INIT_L3_ADDR;
+ bd->bi_memsize = CONFIG_SYS_L3_SIZE;
+
+ probecpu();
+ get_clocks();
+ mem_malloc_init(CONFIG_SPL_RELOC_MALLOC_ADDR,
+ CONFIG_SPL_RELOC_MALLOC_SIZE);
+
+#ifdef CONFIG_SPL_NAND_BOOT
+ nand_spl_load_image(CONFIG_ENV_OFFSET, CONFIG_ENV_SIZE,
+ (uchar *)CONFIG_ENV_ADDR);
+#endif
+#ifdef CONFIG_SPL_MMC_BOOT
+ mmc_initialize(bd);
+ mmc_spl_load_image(CONFIG_ENV_OFFSET, CONFIG_ENV_SIZE,
+ (uchar *)CONFIG_ENV_ADDR);
+#endif
+#ifdef CONFIG_SPL_SPI_BOOT
+ spi_spl_load_image(CONFIG_ENV_OFFSET, CONFIG_ENV_SIZE,
+ (uchar *)CONFIG_ENV_ADDR);
+#endif
+
+ gd->env_addr = (ulong)(CONFIG_ENV_ADDR);
+ gd->env_valid = 1;
+
+ i2c_init_all();
+
+ gd->ram_size = initdram(0);
+
+#ifdef CONFIG_SPL_MMC_BOOT
+ mmc_boot();
+#elif defined(CONFIG_SPL_SPI_BOOT)
+ spi_boot();
+#elif defined(CONFIG_SPL_NAND_BOOT)
+ nand_boot();
+#endif
+}
diff --git a/board/freescale/t102xqds/t1024_pbi.cfg b/board/freescale/t102xqds/t1024_pbi.cfg
new file mode 100644
index 0000000..7b9e9b0
--- /dev/null
+++ b/board/freescale/t102xqds/t1024_pbi.cfg
@@ -0,0 +1,26 @@
+#PBI commands
+#Initialize CPC1
+09010000 00200400
+09138000 00000000
+091380c0 00000100
+#Configure CPC1 as 256KB SRAM
+09010100 00000000
+09010104 fffc0007
+09010f00 08000000
+09010000 80000000
+#Configure LAW for CPC1
+09000cd0 00000000
+09000cd4 fffc0000
+09000cd8 81000011
+#Configure alternate space
+09000010 00000000
+09000014 ff000000
+09000018 81000000
+#Configure SPI controller
+09110000 80000403
+09110020 2d170008
+09110024 00100008
+09110028 00100008
+0911002c 00100008
+#Flush PBL data
+091380c0 000FFFFF
diff --git a/board/freescale/t102xqds/t1024_rcw.cfg b/board/freescale/t102xqds/t1024_rcw.cfg
new file mode 100644
index 0000000..4b8f719
--- /dev/null
+++ b/board/freescale/t102xqds/t1024_rcw.cfg
@@ -0,0 +1,10 @@
+# single-source clock:Sys_Clock = DDR_Refclock = Diff_Sysclk = 100 MHz
+# Core/DDR/Platform/FMan = 1400MHz/1600MT/s/400MHz/700MHz
+
+# PBL preamble and RCW header for T1024QDS
+aa55aa55 010e0100
+# Serdes protocol 0x6F
+0810000e 00000000 00000000 00000000
+37800001 00000012 e8104000 21000000
+00000000 00000000 00000000 00030810
+00000000 036c5a00 00000000 00000006
diff --git a/board/freescale/t102xqds/t102xqds.c b/board/freescale/t102xqds/t102xqds.c
new file mode 100644
index 0000000..f3141b5
--- /dev/null
+++ b/board/freescale/t102xqds/t102xqds.c
@@ -0,0 +1,408 @@
+/*
+ * Copyright 2014 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <command.h>
+#include <i2c.h>
+#include <netdev.h>
+#include <linux/compiler.h>
+#include <asm/mmu.h>
+#include <asm/processor.h>
+#include <asm/cache.h>
+#include <asm/immap_85xx.h>
+#include <asm/fsl_law.h>
+#include <asm/fsl_serdes.h>
+#include <asm/fsl_portals.h>
+#include <asm/fsl_liodn.h>
+#include <fm_eth.h>
+#include <hwconfig.h>
+#include <asm/mpc85xx_gpio.h>
+#include "../common/qixis.h"
+#include "t102xqds.h"
+#include "t102xqds_qixis.h"
+
+DECLARE_GLOBAL_DATA_PTR;
+
+int checkboard(void)
+{
+ char buf[64];
+ struct cpu_type *cpu = gd->arch.cpu;
+ static const char *const freq[] = {"100", "125", "156.25", "100.0"};
+ int clock;
+ u8 sw = QIXIS_READ(arch);
+
+ printf("Board: %sQDS, ", cpu->name);
+ printf("Sys ID: 0x%02x, Board Arch: V%d, ", QIXIS_READ(id), sw >> 4);
+ printf("Board Version: %c, boot from ", (sw & 0xf) + 'A' - 1);
+
+#ifdef CONFIG_SDCARD
+ puts("SD/MMC\n");
+#elif CONFIG_SPIFLASH
+ puts("SPI\n");
+#else
+ sw = QIXIS_READ(brdcfg[0]);
+ sw = (sw & QIXIS_LBMAP_MASK) >> QIXIS_LBMAP_SHIFT;
+
+ if (sw < 0x8)
+ printf("vBank: %d\n", sw);
+ else if (sw == 0x8)
+ puts("PromJet\n");
+ else if (sw == 0x9)
+ puts("NAND\n");
+ else if (sw == 0x15)
+ printf("IFC Card\n");
+ else
+ printf("invalid setting of SW%u\n", QIXIS_LBMAP_SWITCH);
+#endif
+
+ printf("FPGA: v%d (%s), build %d",
+ (int)QIXIS_READ(scver), qixis_read_tag(buf),
+ (int)qixis_read_minor());
+ /* the timestamp string contains "\n" at the end */
+ printf(" on %s", qixis_read_time(buf));
+
+ puts("SERDES Reference: ");
+ sw = QIXIS_READ(brdcfg[2]);
+ clock = (sw >> 6) & 3;
+ printf("Clock1=%sMHz ", freq[clock]);
+ clock = (sw >> 4) & 3;
+ printf("Clock2=%sMHz\n", freq[clock]);
+
+ return 0;
+}
+
+int select_i2c_ch_pca9547(u8 ch)
+{
+ int ret;
+
+ ret = i2c_write(I2C_MUX_PCA_ADDR_PRI, 0, 1, &ch, 1);
+ if (ret) {
+ puts("PCA: failed to select proper channel\n");
+ return ret;
+ }
+
+ return 0;
+}
+
+static int board_mux_lane_to_slot(void)
+{
+ ccsr_gur_t __iomem *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
+ u32 srds_prtcl_s1;
+ u8 brdcfg9;
+
+ srds_prtcl_s1 = in_be32(&gur->rcwsr[4]) &
+ FSL_CORENET2_RCWSR4_SRDS1_PRTCL;
+ srds_prtcl_s1 >>= FSL_CORENET2_RCWSR4_SRDS1_PRTCL_SHIFT;
+
+
+ brdcfg9 = QIXIS_READ(brdcfg[9]);
+ QIXIS_WRITE(brdcfg[9], brdcfg9 | BRDCFG9_XFI_TX_DISABLE);
+
+ switch (srds_prtcl_s1) {
+ case 0:
+ /* SerDes1 is not enabled */
+ break;
+ case 0xd5:
+ case 0x5b:
+ case 0x6b:
+ case 0x77:
+ case 0x6f:
+ case 0x7f:
+ QIXIS_WRITE(brdcfg[12], 0x8c);
+ break;
+ case 0x40:
+ QIXIS_WRITE(brdcfg[12], 0xfc);
+ break;
+ case 0xd6:
+ case 0x5a:
+ case 0x6a:
+ case 0x56:
+ QIXIS_WRITE(brdcfg[12], 0x88);
+ break;
+ case 0x47:
+ QIXIS_WRITE(brdcfg[12], 0xcc);
+ break;
+ case 0x46:
+ QIXIS_WRITE(brdcfg[12], 0xc8);
+ break;
+ case 0x95:
+ case 0x99:
+ brdcfg9 &= ~BRDCFG9_XFI_TX_DISABLE;
+ QIXIS_WRITE(brdcfg[9], brdcfg9);
+ QIXIS_WRITE(brdcfg[12], 0x8c);
+ break;
+ case 0x116:
+ QIXIS_WRITE(brdcfg[12], 0x00);
+ break;
+ case 0x115:
+ case 0x119:
+ case 0x129:
+ case 0x12b:
+ /* Aurora, PCIe, SGMII, SATA */
+ QIXIS_WRITE(brdcfg[12], 0x04);
+ break;
+ default:
+ printf("WARNING: unsupported for SerDes Protocol %d\n",
+ srds_prtcl_s1);
+ return -1;
+ }
+
+ return 0;
+}
+
+#ifdef CONFIG_PPC_T1024
+static void board_mux_setup(void)
+{
+ u8 brdcfg15;
+
+ brdcfg15 = QIXIS_READ(brdcfg[15]);
+ brdcfg15 &= ~BRDCFG15_DIUSEL_MASK;
+
+ if (hwconfig_arg_cmp("pin_mux", "tdm")) {
+ /* Route QE_TDM multiplexed signals to TDM Riser slot */
+ QIXIS_WRITE(brdcfg[15], brdcfg15 | BRDCFG15_DIUSEL_TDM);
+ QIXIS_WRITE(brdcfg[13], BRDCFG13_TDM_INTERFACE << 2);
+ QIXIS_WRITE(brdcfg[5], (QIXIS_READ(brdcfg[5]) &
+ ~BRDCFG5_SPIRTE_MASK) | BRDCFG5_SPIRTE_TDM);
+ } else if (hwconfig_arg_cmp("pin_mux", "ucc")) {
+ /* to UCC (ProfiBus) interface */
+ QIXIS_WRITE(brdcfg[15], brdcfg15 | BRDCFG15_DIUSEL_UCC);
+ } else if (hwconfig_arg_cmp("pin_mux", "hdmi")) {
+ /* to DVI (HDMI) encoder */
+ QIXIS_WRITE(brdcfg[15], brdcfg15 | BRDCFG15_DIUSEL_HDMI);
+ } else if (hwconfig_arg_cmp("pin_mux", "lcd")) {
+ /* to DFP (LCD) encoder */
+ QIXIS_WRITE(brdcfg[15], brdcfg15 | BRDCFG15_LCDFM |
+ BRDCFG15_LCDPD | BRDCFG15_DIUSEL_LCD);
+ }
+
+ if (hwconfig_arg_cmp("adaptor", "sdxc"))
+ /* Route SPI_CS multiplexed signals to SD slot */
+ QIXIS_WRITE(brdcfg[5], (QIXIS_READ(brdcfg[5]) &
+ ~BRDCFG5_SPIRTE_MASK) | BRDCFG5_SPIRTE_SDHC);
+}
+#endif
+
+void board_retimer_ds125df111_init(void)
+{
+ u8 reg;
+
+ /* Retimer DS125DF111 is connected to I2C1_CH7_CH5 */
+ reg = I2C_MUX_CH7;
+ i2c_write(I2C_MUX_PCA_ADDR_PRI, 0, 1, ®, 1);
+ reg = I2C_MUX_CH5;
+ i2c_write(I2C_MUX_PCA_ADDR_SEC, 0, 1, ®, 1);
+
+ /* Access to Control/Shared register */
+ reg = 0x0;
+ i2c_write(I2C_RETIMER_ADDR, 0xff, 1, ®, 1);
+
+ /* Read device revision and ID */
+ i2c_read(I2C_RETIMER_ADDR, 1, 1, ®, 1);
+ debug("Retimer version id = 0x%x\n", reg);
+
+ /* Enable Broadcast */
+ reg = 0x0c;
+ i2c_write(I2C_RETIMER_ADDR, 0xff, 1, ®, 1);
+
+ /* Reset Channel Registers */
+ i2c_read(I2C_RETIMER_ADDR, 0, 1, ®, 1);
+ reg |= 0x4;
+ i2c_write(I2C_RETIMER_ADDR, 0, 1, ®, 1);
+
+ /* Enable override divider select and Enable Override Output Mux */
+ i2c_read(I2C_RETIMER_ADDR, 9, 1, ®, 1);
+ reg |= 0x24;
+ i2c_write(I2C_RETIMER_ADDR, 9, 1, ®, 1);
+
+ /* Select VCO Divider to full rate (000) */
+ i2c_read(I2C_RETIMER_ADDR, 0x18, 1, ®, 1);
+ reg &= 0x8f;
+ i2c_write(I2C_RETIMER_ADDR, 0x18, 1, ®, 1);
+
+ /* Select active PFD MUX input as re-timed data (001) */
+ i2c_read(I2C_RETIMER_ADDR, 0x1e, 1, ®, 1);
+ reg &= 0x3f;
+ reg |= 0x20;
+ i2c_write(I2C_RETIMER_ADDR, 0x1e, 1, ®, 1);
+
+ /* Set data rate as 10.3125 Gbps */
+ reg = 0x0;
+ i2c_write(I2C_RETIMER_ADDR, 0x60, 1, ®, 1);
+ reg = 0xb2;
+ i2c_write(I2C_RETIMER_ADDR, 0x61, 1, ®, 1);
+ reg = 0x90;
+ i2c_write(I2C_RETIMER_ADDR, 0x62, 1, ®, 1);
+ reg = 0xb3;
+ i2c_write(I2C_RETIMER_ADDR, 0x63, 1, ®, 1);
+ reg = 0xcd;
+ i2c_write(I2C_RETIMER_ADDR, 0x64, 1, ®, 1);
+}
+
+int board_early_init_r(void)
+{
+#ifdef CONFIG_SYS_FLASH_BASE
+ const unsigned int flashbase = CONFIG_SYS_FLASH_BASE;
+ int flash_esel = find_tlb_idx((void *)flashbase, 1);
+
+ /*
+ * Remap Boot flash + PROMJET region to caching-inhibited
+ * so that flash can be erased properly.
+ */
+
+ /* Flush d-cache and invalidate i-cache of any FLASH data */
+ flush_dcache();
+ invalidate_icache();
+
+ if (flash_esel == -1) {
+ /* very unlikely unless something is messed up */
+ puts("Error: Could not find TLB for FLASH BASE\n");
+ flash_esel = 2; /* give our best effort to continue */
+ } else {
+ /* invalidate existing TLB entry for flash + promjet */
+ disable_tlb(flash_esel);
+ }
+
+ set_tlb(1, flashbase, CONFIG_SYS_FLASH_BASE_PHYS,
+ MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+ 0, flash_esel, BOOKE_PAGESZ_256M, 1);
+#endif
+ set_liodns();
+#ifdef CONFIG_SYS_DPAA_QBMAN
+ setup_portals();
+#endif
+ select_i2c_ch_pca9547(I2C_MUX_CH_DEFAULT);
+ board_mux_lane_to_slot();
+ board_retimer_ds125df111_init();
+
+ /* Increase IO drive strength to address FCS error on RGMII */
+ out_be32((unsigned *)CONFIG_SYS_FSL_SCFG_IODSECR1_ADDR, 0xbfdb7800);
+
+ return 0;
+}
+
+unsigned long get_board_sys_clk(void)
+{
+ u8 sysclk_conf = QIXIS_READ(brdcfg[1]);
+
+ switch (sysclk_conf & 0x0F) {
+ case QIXIS_SYSCLK_64:
+ return 64000000;
+ case QIXIS_SYSCLK_83:
+ return 83333333;
+ case QIXIS_SYSCLK_100:
+ return 100000000;
+ case QIXIS_SYSCLK_125:
+ return 125000000;
+ case QIXIS_SYSCLK_133:
+ return 133333333;
+ case QIXIS_SYSCLK_150:
+ return 150000000;
+ case QIXIS_SYSCLK_160:
+ return 160000000;
+ case QIXIS_SYSCLK_166:
+ return 166666666;
+ }
+ return 66666666;
+}
+
+unsigned long get_board_ddr_clk(void)
+{
+ u8 ddrclk_conf = QIXIS_READ(brdcfg[1]);
+
+ switch ((ddrclk_conf & 0x30) >> 4) {
+ case QIXIS_DDRCLK_100:
+ return 100000000;
+ case QIXIS_DDRCLK_125:
+ return 125000000;
+ case QIXIS_DDRCLK_133:
+ return 133333333;
+ }
+ return 66666666;
+}
+
+#define NUM_SRDS_PLL 2
+int misc_init_r(void)
+{
+#ifdef CONFIG_PPC_T1024
+ board_mux_setup();
+#endif
+ return 0;
+}
+
+void fdt_fixup_spi_mux(void *blob)
+{
+ int nodeoff = 0;
+
+ if (hwconfig_arg_cmp("pin_mux", "tdm")) {
+ while ((nodeoff = fdt_node_offset_by_compatible(blob, 0,
+ "eon,en25s64")) >= 0) {
+ fdt_del_node(blob, nodeoff);
+ }
+ } else {
+ /* remove tdm node */
+ while ((nodeoff = fdt_node_offset_by_compatible(blob, 0,
+ "maxim,ds26522")) >= 0) {
+ fdt_del_node(blob, nodeoff);
+ }
+ }
+}
+
+int ft_board_setup(void *blob, bd_t *bd)
+{
+ phys_addr_t base;
+ phys_size_t size;
+
+ ft_cpu_setup(blob, bd);
+
+ base = getenv_bootm_low();
+ size = getenv_bootm_size();
+
+ fdt_fixup_memory(blob, (u64)base, (u64)size);
+
+#ifdef CONFIG_PCI
+ pci_of_setup(blob, bd);
+#endif
+
+ fdt_fixup_liodn(blob);
+
+#ifdef CONFIG_HAS_FSL_DR_USB
+ fdt_fixup_dr_usb(blob, bd);
+#endif
+
+#ifdef CONFIG_SYS_DPAA_FMAN
+ fdt_fixup_fman_ethernet(blob);
+ fdt_fixup_board_enet(blob);
+#endif
+ fdt_fixup_spi_mux(blob);
+
+ return 0;
+}
+
+void qixis_dump_switch(void)
+{
+ int i, nr_of_cfgsw;
+
+ QIXIS_WRITE(cms[0], 0x00);
+ nr_of_cfgsw = QIXIS_READ(cms[1]);
+
+ puts("DIP switch settings dump:\n");
+ for (i = 1; i <= nr_of_cfgsw; i++) {
+ QIXIS_WRITE(cms[0], i);
+ printf("SW%d = (0x%02x)\n", i, QIXIS_READ(cms[1]));
+ }
+}
+
+#ifdef CONFIG_DEEP_SLEEP
+void board_mem_sleep_setup(void)
+{
+ /* does not provide HW signals for power management */
+ QIXIS_WRITE(pwr_ctl[1], (QIXIS_READ(pwr_ctl[1]) & ~0x2));
+ /* Disable MCKE isolation */
+ gpio_set_value(2, 0);
+ udelay(1);
+}
+#endif
diff --git a/board/freescale/t102xqds/t102xqds.h b/board/freescale/t102xqds/t102xqds.h
new file mode 100644
index 0000000..64ff623
--- /dev/null
+++ b/board/freescale/t102xqds/t102xqds.h
@@ -0,0 +1,14 @@
+/*
+ * Copyright 2014 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#ifndef __T102x_QDS_H__
+#define __T102x_QDS_H__
+
+void fdt_fixup_board_enet(void *blob);
+void pci_of_setup(void *blob, bd_t *bd);
+int select_i2c_ch_pca9547(u8 ch);
+
+#endif
diff --git a/board/freescale/t102xqds/t102xqds_qixis.h b/board/freescale/t102xqds/t102xqds_qixis.h
new file mode 100644
index 0000000..a429fb7
--- /dev/null
+++ b/board/freescale/t102xqds/t102xqds_qixis.h
@@ -0,0 +1,64 @@
+/*
+ * Copyright 2014 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#ifndef __T1024QDS_QIXIS_H__
+#define __T1024QDS_QIXIS_H__
+
+/* Definitions of QIXIS Registers for T1024/T1023 QDS */
+
+/* BRDCFG4[4:7]] select EC1 and EC2 as a pair */
+#define BRDCFG4_EMISEL_MASK 0xE0
+#define BRDCFG4_EMISEL_SHIFT 5
+
+/* BRDCFG5[0:1] controls routing and use of I2C3 & I2C4 ports*/
+#define BRDCFG5_IMX_MASK 0xC0
+#define BRDCFG5_IMX_DIU 0x80
+
+#define BRDCFG5_SPIRTE_MASK 0x07
+#define BRDCFG5_SPIRTE_TDM 0x01
+#define BRDCFG5_SPIRTE_SDHC 0x02
+#define BRDCFG9_XFI_TX_DISABLE 0x10
+
+/* BRDCFG13[0:5] TDM configuration and setup */
+#define BRDCFG13_TDM_MASK 0xfc
+#define BRDCFG13_TDM_INTERFACE 0x37
+#define BRDCFG13_HDLC_LOOPBACK 0x29
+#define BRDCFG13_TDM_LOOPBACK 0x31
+
+/* BRDCFG15[3] controls LCD Panel Powerdown */
+#define BRDCFG15_LCDFM 0x20
+#define BRDCFG15_LCDPD 0x10
+#define BRDCFG15_LCDPD_MASK 0x10
+#define BRDCFG15_LCDPD_ENABLED 0x00
+
+/* BRDCFG15[6:7] controls DIU MUX selction*/
+#define BRDCFG15_DIUSEL_MASK 0x03
+#define BRDCFG15_DIUSEL_HDMI 0x00
+#define BRDCFG15_DIUSEL_LCD 0x01
+#define BRDCFG15_DIUSEL_UCC 0x02
+#define BRDCFG15_DIUSEL_TDM 0x03
+
+/* SYSCLK */
+#define QIXIS_SYSCLK_66 0x0
+#define QIXIS_SYSCLK_83 0x1
+#define QIXIS_SYSCLK_100 0x2
+#define QIXIS_SYSCLK_125 0x3
+#define QIXIS_SYSCLK_133 0x4
+#define QIXIS_SYSCLK_150 0x5
+#define QIXIS_SYSCLK_160 0x6
+#define QIXIS_SYSCLK_166 0x7
+#define QIXIS_SYSCLK_64 0x8
+
+/* DDRCLK */
+#define QIXIS_DDRCLK_66 0x0
+#define QIXIS_DDRCLK_100 0x1
+#define QIXIS_DDRCLK_125 0x2
+#define QIXIS_DDRCLK_133 0x3
+
+
+#define QIXIS_SRDS1CLK_122 0x5a
+#define QIXIS_SRDS1CLK_125 0x5e
+#endif
diff --git a/board/freescale/t102xqds/tlb.c b/board/freescale/t102xqds/tlb.c
new file mode 100644
index 0000000..409e173
--- /dev/null
+++ b/board/freescale/t102xqds/tlb.c
@@ -0,0 +1,117 @@
+/*
+ * Copyright 2014 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <asm/mmu.h>
+
+struct fsl_e_tlb_entry tlb_table[] = {
+ /* TLB 0 - for temp stack in cache */
+ SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR,
+ CONFIG_SYS_INIT_RAM_ADDR_PHYS,
+ MAS3_SX|MAS3_SW|MAS3_SR, 0,
+ 0, 0, BOOKE_PAGESZ_4K, 0),
+ SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 4 * 1024,
+ CONFIG_SYS_INIT_RAM_ADDR_PHYS + 4 * 1024,
+ MAS3_SX|MAS3_SW|MAS3_SR, 0,
+ 0, 0, BOOKE_PAGESZ_4K, 0),
+ SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 8 * 1024,
+ CONFIG_SYS_INIT_RAM_ADDR_PHYS + 8 * 1024,
+ MAS3_SX|MAS3_SW|MAS3_SR, 0,
+ 0, 0, BOOKE_PAGESZ_4K, 0),
+ SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 12 * 1024,
+ CONFIG_SYS_INIT_RAM_ADDR_PHYS + 12 * 1024,
+ MAS3_SX|MAS3_SW|MAS3_SR, 0,
+ 0, 0, BOOKE_PAGESZ_4K, 0),
+
+ /* TLB 1 */
+ /* *I*** - Covers boot page */
+#if defined(CONFIG_SYS_RAMBOOT) && defined(CONFIG_SYS_INIT_L3_ADDR)
+ /*
+ * *I*G - L3SRAM. When L3 is used as 256K SRAM, the address of the
+ * SRAM is at 0xfffc0000, it covered the 0xfffff000.
+ */
+ SET_TLB_ENTRY(1, CONFIG_SYS_INIT_L3_ADDR, CONFIG_SYS_INIT_L3_ADDR,
+ MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+ 0, 0, BOOKE_PAGESZ_256K, 1),
+#else
+ SET_TLB_ENTRY(1, 0xfffff000, 0xfffff000,
+ MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+ 0, 0, BOOKE_PAGESZ_4K, 1),
+#endif
+
+ /* *I*G* - CCSRBAR */
+ SET_TLB_ENTRY(1, CONFIG_SYS_CCSRBAR, CONFIG_SYS_CCSRBAR_PHYS,
+ MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+ 0, 1, BOOKE_PAGESZ_16M, 1),
+
+ /* *I*G* - Flash, localbus */
+ /* This will be changed to *I*G* after relocation to RAM. */
+ SET_TLB_ENTRY(1, CONFIG_SYS_FLASH_BASE, CONFIG_SYS_FLASH_BASE_PHYS,
+ MAS3_SX|MAS3_SR, MAS2_W|MAS2_G,
+ 0, 2, BOOKE_PAGESZ_256M, 1),
+
+#ifndef CONFIG_SPL_BUILD
+ /* *I*G* - PCI */
+ SET_TLB_ENTRY(1, CONFIG_SYS_PCIE1_MEM_VIRT, CONFIG_SYS_PCIE1_MEM_PHYS,
+ MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+ 0, 3, BOOKE_PAGESZ_1G, 1),
+
+ /* *I*G* - PCI I/O */
+ SET_TLB_ENTRY(1, CONFIG_SYS_PCIE1_IO_VIRT, CONFIG_SYS_PCIE1_IO_PHYS,
+ MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+ 0, 4, BOOKE_PAGESZ_256K, 1),
+
+ /* Bman/Qman */
+#ifdef CONFIG_SYS_BMAN_MEM_PHYS
+ SET_TLB_ENTRY(1, CONFIG_SYS_BMAN_MEM_BASE, CONFIG_SYS_BMAN_MEM_PHYS,
+ MAS3_SX|MAS3_SW|MAS3_SR, 0,
+ 0, 5, BOOKE_PAGESZ_16M, 1),
+ SET_TLB_ENTRY(1, CONFIG_SYS_BMAN_MEM_BASE + 0x01000000,
+ CONFIG_SYS_BMAN_MEM_PHYS + 0x01000000,
+ MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+ 0, 6, BOOKE_PAGESZ_16M, 1),
+#endif
+#ifdef CONFIG_SYS_QMAN_MEM_PHYS
+ SET_TLB_ENTRY(1, CONFIG_SYS_QMAN_MEM_BASE, CONFIG_SYS_QMAN_MEM_PHYS,
+ MAS3_SX|MAS3_SW|MAS3_SR, 0,
+ 0, 7, BOOKE_PAGESZ_16M, 1),
+ SET_TLB_ENTRY(1, CONFIG_SYS_QMAN_MEM_BASE + 0x01000000,
+ CONFIG_SYS_QMAN_MEM_PHYS + 0x01000000,
+ MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+ 0, 8, BOOKE_PAGESZ_16M, 1),
+#endif
+#endif
+#ifdef CONFIG_SYS_DCSRBAR_PHYS
+ SET_TLB_ENTRY(1, CONFIG_SYS_DCSRBAR, CONFIG_SYS_DCSRBAR_PHYS,
+ MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+ 0, 9, BOOKE_PAGESZ_4M, 1),
+#endif
+#ifdef CONFIG_SYS_NAND_BASE
+ SET_TLB_ENTRY(1, CONFIG_SYS_NAND_BASE, CONFIG_SYS_NAND_BASE_PHYS,
+ MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+ 0, 10, BOOKE_PAGESZ_64K, 1),
+#endif
+#ifdef QIXIS_BASE
+ SET_TLB_ENTRY(1, QIXIS_BASE, QIXIS_BASE_PHYS,
+ MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+ 0, 11, BOOKE_PAGESZ_4K, 1),
+#endif
+
+#if defined(CONFIG_RAMBOOT_PBL) && !defined(CONFIG_SPL_BUILD)
+ SET_TLB_ENTRY(1, CONFIG_SYS_DDR_SDRAM_BASE, CONFIG_SYS_DDR_SDRAM_BASE,
+ MAS3_SX|MAS3_SW|MAS3_SR, 0,
+ 0, 12, BOOKE_PAGESZ_1G, 1),
+ SET_TLB_ENTRY(1, CONFIG_SYS_DDR_SDRAM_BASE + 0x40000000,
+ CONFIG_SYS_DDR_SDRAM_BASE + 0x40000000,
+ MAS3_SX|MAS3_SW|MAS3_SR, 0,
+ 0, 13, BOOKE_PAGESZ_1G, 1)
+#endif
+ /* entry 14 and 15 has been used hard coded, they will be disabled
+ * in cpu_init_f, so if needed more, will use entry 16 later.
+ */
+};
+
+int num_tlb_entries = ARRAY_SIZE(tlb_table);
diff --git a/board/freescale/t102xrdb/Kconfig b/board/freescale/t102xrdb/Kconfig
new file mode 100644
index 0000000..10d49f5
--- /dev/null
+++ b/board/freescale/t102xrdb/Kconfig
@@ -0,0 +1,12 @@
+if TARGET_T102XRDB
+
+config SYS_BOARD
+ default "t102xrdb"
+
+config SYS_VENDOR
+ default "freescale"
+
+config SYS_CONFIG_NAME
+ default "T102xRDB"
+
+endif
diff --git a/board/freescale/t102xrdb/MAINTAINERS b/board/freescale/t102xrdb/MAINTAINERS
new file mode 100644
index 0000000..dc554d4
--- /dev/null
+++ b/board/freescale/t102xrdb/MAINTAINERS
@@ -0,0 +1,10 @@
+T102XRDB BOARD
+M: Shengzhou Liu <Shengzhou.Liu@freescale.com>
+S: Maintained
+F: board/freescale/t102xrdb/
+F: include/configs/T102xRDB.h
+F: configs/T1024RDB_defconfig
+F: configs/T1024RDB_NAND_defconfig
+F: configs/T1024RDB_SDCARD_defconfig
+F: configs/T1024RDB_SPIFLASH_defconfig
+F: configs/T1024RDB_SECURE_BOOT_defconfig
diff --git a/board/freescale/t102xrdb/Makefile b/board/freescale/t102xrdb/Makefile
new file mode 100644
index 0000000..a0cf8f6
--- /dev/null
+++ b/board/freescale/t102xrdb/Makefile
@@ -0,0 +1,17 @@
+#
+# Copyright 2014 Freescale Semiconductor, Inc.
+#
+# SPDX-License-Identifier: GPL-2.0+
+#
+
+ifdef CONFIG_SPL_BUILD
+obj-y += spl.o
+else
+obj-y += t102xrdb.o
+obj-y += cpld.o
+obj-y += eth_t102xrdb.o
+obj-$(CONFIG_PCI) += pci.o
+endif
+obj-y += ddr.o
+obj-y += law.o
+obj-y += tlb.o
diff --git a/board/freescale/t102xrdb/README b/board/freescale/t102xrdb/README
new file mode 100644
index 0000000..2b17f50
--- /dev/null
+++ b/board/freescale/t102xrdb/README
@@ -0,0 +1,258 @@
+T1024 SoC Overview
+------------------
+The T1024/T1023 dual core and T1014/T1013 single core QorIQ communication processor
+combines two or one 64-bit Power Architecture e5500 core respectively with high
+performance datapath acceleration logic, and network peripheral bus interfaces
+required for networking and telecommunications. This processor can be used in
+applications such as enterprise WLAN access points, routers, switches, firewall
+and other packet processing intensive small enterprise and branch office appliances,
+and general-purpose embedded computing. Its high level of integration offers
+significant performance benefits and greatly helps to simplify board design.
+
+
+The T1024 SoC includes the following function and features:
+- two e5500 cores, each with a private 256 KB L2 cache
+ - Up to 1.4 GHz with 64-bit ISA support (Power Architecture v2.06-compliant)
+ - Three levels of instructions: User, supervisor, and hypervisor
+ - Independent boot and reset
+ - Secure boot capability
+- 256 KB shared L3 CoreNet platform cache (CPC)
+- Interconnect CoreNet platform
+ - CoreNet coherency manager supporting coherent and noncoherent transactions
+ with prioritization and bandwidth allocation amongst CoreNet endpoints
+ - 150 Gbps coherent read bandwidth
+- 32-/64-bit DDR3L/DDR4 SDRAM memory controller with ECC and interleaving support
+- Data Path Acceleration Architecture (DPAA) incorporating acceleration for the following functions:
+ - Packet parsing, classification, and distribution
+ - Queue management for scheduling, packet sequencing, and congestion management
+ - Cryptography Acceleration (SEC 5.x)
+ - IEEE 1588 support
+ - Hardware buffer management for buffer allocation and deallocation
+ - MACSEC on DPAA-based Ethernet ports
+- Ethernet interfaces
+ - Four 1 Gbps Ethernet controllers
+- Parallel Ethernet interfaces
+ - Two RGMII interfaces
+- High speed peripheral interfaces
+ - Three PCI Express 2.0 controllers/ports running at up to 5 GHz
+ - One SATA controller supporting 1.5 and 3.0 Gb/s operation
+ - One QSGMII interface
+ - Four SGMII interface supporting 1000 Mbps
+ - Three SGMII interfaces supporting up to 2500 Mbps
+ - 10GbE XFI or 10Base-KR interface
+- Additional peripheral interfaces
+ - Two USB 2.0 controllers with integrated PHY
+ - SD/eSDHC/eMMC
+ - eSPI controller
+ - Four I2C controllers
+ - Four UARTs
+ - Four GPIO controllers
+ - Integrated flash controller (IFC)
+ - LCD interface (DIU) with 12 bit dual data rate
+- Multicore programmable interrupt controller (PIC)
+- Two 8-channel DMA engines
+- Single source clocking implementation
+- Deep Sleep power implementaion (wakeup from GPIO/Timer/Ethernet/USB)
+- QUICC Engine block
+ - 32-bit RISC controller for flexible support of the communications peripherals
+ - Serial DMA channel for receive and transmit on all serial channels
+ - Two universal communication controllers, supporting TDM, HDLC, and UART
+
+T1023 Personality
+------------------
+T1023 is a reduced personality of T1024 without QUICC Engine, DIU, and
+unavailable deep sleep. Rest of the blocks are almost same as T1024.
+Differences between T1024 and T1023
+Feature T1024 T1023
+QUICC Engine: yes no
+DIU: yes no
+Deep Sleep: yes no
+I2C controller: 4 3
+DDR: 64-bit 32-bit
+IFC: 32-bit 28-bit
+
+
+T1024RDB board Overview
+-----------------------
+ - Ethernet
+ - Two on-board 10M/100M/1G bps RGMII ethernet ports
+ - One on-board 10G bps Base-T port.
+ - DDR Memory
+ - Supports 64-bit 4GB DDR3L DIMM
+ - PCIe
+ - One on-board PCIe slot.
+ - Two on-board PCIe Mini-PCIe connectors.
+ - IFC/Local Bus
+ - NOR: 128MB 16-bit NOR Flash
+ - NAND: 1GB 8-bit NAND flash
+ - CPLD: for system controlling with programable header on-board
+ - USB
+ - Supports two USB 2.0 ports with integrated PHYs
+ - Two type A ports with 5V@1.5A per port.
+ - SDHC
+ - one SD connector supporting 1.8V/3.3V via J53.
+ - SPI
+ - On-board 64MB SPI flash
+ - Other
+ - Two Serial ports
+ - Four I2C ports
+
+
+Memory map on T1024RDB
+----------------------
+Start Address End Address Description Size
+0xF_FFDF_0000 0xF_FFDF_0FFF IFC - CPLD 4KB
+0xF_FF80_0000 0xF_FF80_FFFF IFC - NAND Flash 64KB
+0xF_FE00_0000 0xF_FEFF_FFFF CCSRBAR 16MB
+0xF_F802_0000 0xF_F802_FFFF PCI Express 3 I/O Space 64KB
+0xF_F801_0000 0xF_F801_FFFF PCI Express 2 I/O Space 64KB
+0xF_F800_0000 0xF_F800_FFFF PCI Express 1 I/O Space 64KB
+0xF_F600_0000 0xF_F7FF_FFFF Queue manager software portal 32MB
+0xF_F400_0000 0xF_F5FF_FFFF Buffer manager software portal 32MB
+0xF_E800_0000 0xF_EFFF_FFFF IFC - NOR Flash 128MB
+0xF_0000_0000 0xF_003F_FFFF DCSR 4MB
+0xC_2000_0000 0xC_2FFF_FFFF PCI Express 3 Mem Space 256MB
+0xC_1000_0000 0xC_1FFF_FFFF PCI Express 2 Mem Space 256MB
+0xC_0000_0000 0xC_0FFF_FFFF PCI Express 1 Mem Space 256MB
+0x0_0000_0000 0x0_ffff_ffff DDR 4GB
+
+
+128MB NOR Flash memory Map
+--------------------------
+Start Address End Address Definition Max size
+0xEFF40000 0xEFFFFFFF u-boot (current bank) 768KB
+0xEFF20000 0xEFF3FFFF u-boot env (current bank) 128KB
+0xEFF00000 0xEFF1FFFF FMAN Ucode (current bank) 128KB
+0xEFE00000 0xEFE3FFFF QE firmware (current bank) 256KB
+0xED300000 0xEFEFFFFF rootfs (alt bank) 44MB
+0xEC800000 0xEC8FFFFF Hardware device tree (alt bank) 1MB
+0xEC020000 0xEC7FFFFF Linux.uImage (alt bank) 7MB + 875KB
+0xEC000000 0xEC01FFFF RCW (alt bank) 128KB
+0xEBF40000 0xEBFFFFFF u-boot (alt bank) 768KB
+0xEBF20000 0xEBF3FFFF u-boot env (alt bank) 128KB
+0xEBF00000 0xEBF1FFFF FMAN ucode (alt bank) 128KB
+0xEBE00000 0xEBE3FFFF QE firmware (alt bank) 256KB
+0xE9300000 0xEBEFFFFF rootfs (current bank) 44MB
+0xE8800000 0xE88FFFFF Hardware device tree (cur bank) 1MB
+0xE8020000 0xE86FFFFF Linux.uImage (current bank) 7MB + 875KB
+0xE8000000 0xE801FFFF RCW (current bank) 128KB
+
+
+T1024 Clock frequency
+---------------------
+BIN Core DDR Platform FMan
+Bin1: 1400MHz 1600MT/s 400MHz 700MHz
+Bin2: 1200MHz 1600MT/s 400MHz 600MHz
+Bin3: 1000MHz 1600MT/s 400MHz 500MHz
+
+
+Software configurations and board settings
+------------------------------------------
+1. NOR boot:
+ a. build NOR boot image
+ $ make T1024RDB_defconfig
+ $ make
+ b. program u-boot.bin image to NOR flash
+ => tftp 1000000 u-boot.bin
+ => pro off all;era eff40000 efffffff;cp.b 1000000 eff40000 $filesize
+ set SW1[1:8] = '00010011', SW2[1] = '1', SW3[4] = '0' for NOR boot
+
+ Switching between default bank0 and alternate bank4 on NOR flash
+ To change boot source to vbank4:
+ via software: run command 'cpld reset altbank' in u-boot.
+ via DIP-switch: set SW3[5:7] = '100'
+
+ To change boot source to vbank0:
+ via software: run command 'cpld reset' in u-boot.
+ via DIP-Switch: set SW3[5:7] = '000'
+
+2. NAND Boot:
+ a. build PBL image for NAND boot
+ $ make T1024RDB_NAND_defconfig
+ $ make
+ b. program u-boot-with-spl-pbl.bin to NAND flash
+ => tftp 1000000 u-boot-with-spl-pbl.bin
+ => nand erase 0 $filesize
+ => nand write 1000000 0 $filesize
+ set SW1[1:8] = '10001000', SW2[1] = '1', SW3[4] = '1' for NAND boot
+
+3. SPI Boot:
+ a. build PBL image for SPI boot
+ $ make T1024RDB_SPIFLASH_defconfig
+ $ make
+ b. program u-boot-with-spl-pbl.bin to SPI flash
+ => tftp 1000000 u-boot-with-spl-pbl.bin
+ => sf probe 0
+ => sf erase 0 f0000
+ => sf write 1000000 0 $filesize
+ set SW1[1:8] = '00100010', SW2[1] ='1' for SPI boot
+
+4. SD Boot:
+ a. build PBL image for SD boot
+ $ make T1024RDB_SDCARD_defconfig
+ $ make
+ b. program u-boot-with-spl-pbl.bin to SD/MMC card
+ => tftp 1000000 u-boot-with-spl-pbl.bin
+ => mmc write 1000000 8 0x800
+ => tftp 1000000 fsl_fman_ucode_t1024_xx.bin
+ => mmc write 1000000 0x820 80
+ set SW1[1:8] = '00100000', SW2[1] = '0' for SD boot
+
+
+2-stage NAND/SPI/SD boot loader
+-------------------------------
+PBL initializes the internal CPC-SRAM and copy SPL(160K) to SRAM.
+SPL further initializes DDR using SPD and environment variables
+and copy u-boot(768 KB) from NAND/SPI/SD device to DDR.
+Finally SPL transers control to u-boot for futher booting.
+
+SPL has following features:
+ - Executes within 256K
+ - No relocation required
+
+Run time view of SPL framework
+-------------------------------------------------
+|Area | Address |
+-------------------------------------------------
+|SecureBoot header | 0xFFFC0000 (32KB) |
+-------------------------------------------------
+|GD, BD | 0xFFFC8000 (4KB) |
+-------------------------------------------------
+|ENV | 0xFFFC9000 (8KB) |
+-------------------------------------------------
+|HEAP | 0xFFFCB000 (30KB) |
+-------------------------------------------------
+|STACK | 0xFFFD8000 (22KB) |
+-------------------------------------------------
+|U-boot SPL | 0xFFFD8000 (160KB) |
+-------------------------------------------------
+
+NAND Flash memory Map on T1024RDB
+-------------------------------------------------------------
+Start End Definition Size
+0x000000 0x0FFFFF u-boot 1MB(2 block)
+0x100000 0x17FFFF u-boot env 512KB(1 block)
+0x180000 0x1FFFFF FMAN Ucode 512KB(1 block)
+0x200000 0x27FFFF QE Firmware 512KB(1 block)
+
+
+SD Card memory Map on T1024RDB
+----------------------------------------------------
+Block #blocks Definition Size
+0x008 2048 u-boot img 1MB
+0x800 0016 u-boot env 8KB
+0x820 0256 FMAN Ucode 128KB
+0x920 0256 QE Firmware 128KB
+
+
+SPI Flash memory Map on T1024RDB
+----------------------------------------------------
+Start End Definition Size
+0x000000 0x0FFFFF u-boot img 1MB
+0x100000 0x101FFF u-boot env 8KB
+0x110000 0x12FFFF FMAN Ucode 128KB
+0x130000 0x14FFFF QE Firmware 128KB
+
+
+For more details, please refer to T1024RDB Reference Manual and access
+website www.freescale.com and Freescale QorIQ SDK Infocenter document.
diff --git a/board/freescale/t102xrdb/cpld.c b/board/freescale/t102xrdb/cpld.c
new file mode 100644
index 0000000..c03894a
--- /dev/null
+++ b/board/freescale/t102xrdb/cpld.c
@@ -0,0 +1,103 @@
+/**
+ * Copyright 2014 Freescale Semiconductor
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ *
+ * Freescale T1024RDB board-specific CPLD controlling supports.
+ *
+ * The following macros need to be defined:
+ */
+
+#include <common.h>
+#include <command.h>
+#include <asm/io.h>
+#include "cpld.h"
+
+u8 cpld_read(unsigned int reg)
+{
+ void *p = (void *)CONFIG_SYS_CPLD_BASE;
+
+ return in_8(p + reg);
+}
+
+void cpld_write(unsigned int reg, u8 value)
+{
+ void *p = (void *)CONFIG_SYS_CPLD_BASE;
+
+ out_8(p + reg, value);
+}
+
+/**
+ * Set the boot bank to the alternate bank
+ */
+void cpld_set_altbank(void)
+{
+ u8 reg = CPLD_READ(flash_csr);
+
+ reg = (reg & ~CPLD_BANK_SEL_MASK) | CPLD_LBMAP_ALTBANK;
+
+ CPLD_WRITE(flash_csr, reg);
+ CPLD_WRITE(reset_ctl1, CPLD_LBMAP_RESET);
+}
+
+/**
+ * Set the boot bank to the default bank
+ */
+void cpld_set_defbank(void)
+{
+ u8 reg = CPLD_READ(flash_csr);
+
+ reg = (reg & ~CPLD_BANK_SEL_MASK) | CPLD_LBMAP_DFLTBANK;
+
+ CPLD_WRITE(flash_csr, reg);
+ CPLD_WRITE(reset_ctl1, CPLD_LBMAP_RESET);
+}
+
+static void cpld_dump_regs(void)
+{
+ printf("cpld_ver = 0x%02x\n", CPLD_READ(cpld_ver));
+ printf("cpld_ver_sub = 0x%02x\n", CPLD_READ(cpld_ver_sub));
+ printf("hw_ver = 0x%02x\n", CPLD_READ(hw_ver));
+ printf("sw_ver = 0x%02x\n", CPLD_READ(sw_ver));
+ printf("reset_ctl1 = 0x%02x\n", CPLD_READ(reset_ctl1));
+ printf("reset_ctl2 = 0x%02x\n", CPLD_READ(reset_ctl2));
+ printf("int_status = 0x%02x\n", CPLD_READ(int_status));
+ printf("flash_csr = 0x%02x\n", CPLD_READ(flash_csr));
+ printf("fan_ctl_status = 0x%02x\n", CPLD_READ(fan_ctl_status));
+ printf("led_ctl_status = 0x%02x\n", CPLD_READ(led_ctl_status));
+ printf("sfp_ctl_status = 0x%02x\n", CPLD_READ(sfp_ctl_status));
+ printf("misc_ctl_status = 0x%02x\n", CPLD_READ(misc_ctl_status));
+ printf("boot_override = 0x%02x\n", CPLD_READ(boot_override));
+ printf("boot_config1 = 0x%02x\n", CPLD_READ(boot_config1));
+ printf("boot_config2 = 0x%02x\n", CPLD_READ(boot_config2));
+ putc('\n');
+}
+
+int do_cpld(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[])
+{
+ int rc = 0;
+
+ if (argc <= 1)
+ return cmd_usage(cmdtp);
+
+ if (strcmp(argv[1], "reset") == 0) {
+ if (strcmp(argv[2], "altbank") == 0)
+ cpld_set_altbank();
+ else
+ cpld_set_defbank();
+ } else if (strcmp(argv[1], "dump") == 0) {
+ cpld_dump_regs();
+ } else {
+ rc = cmd_usage(cmdtp);
+ }
+
+ return rc;
+}
+
+U_BOOT_CMD(
+ cpld, CONFIG_SYS_MAXARGS, 1, do_cpld,
+ "Reset the board or alternate bank",
+ "reset - hard reset to default bank\n"
+ "cpld reset altbank - reset to alternate bank\n"
+ "cpld dump - display the CPLD registers\n"
+ );
diff --git a/board/freescale/t102xrdb/cpld.h b/board/freescale/t102xrdb/cpld.h
new file mode 100644
index 0000000..5a3100f
--- /dev/null
+++ b/board/freescale/t102xrdb/cpld.h
@@ -0,0 +1,45 @@
+/**
+ * Copyright 2014 Freescale Semiconductor
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ *
+ */
+
+struct cpld_data {
+ u8 cpld_ver; /* 0x00 - CPLD Major Revision Register */
+ u8 cpld_ver_sub; /* 0x01 - CPLD Minor Revision Register */
+ u8 hw_ver; /* 0x02 - Hardware Revision Register */
+ u8 sw_ver; /* 0x03 - Software Revision register */
+ u8 res0[12]; /* 0x04 - 0x0F - not used */
+ u8 reset_ctl1; /* 0x10 - Reset control Register1 */
+ u8 reset_ctl2; /* 0x11 - Reset control Register2 */
+ u8 int_status; /* 0x12 - Interrupt status Register */
+ u8 flash_csr; /* 0x13 - Flash control and status register */
+ u8 fan_ctl_status; /* 0x14 - Fan control and status register */
+ u8 led_ctl_status; /* 0x15 - LED control and status register */
+ u8 sfp_ctl_status; /* 0x16 - SFP control and status register */
+ u8 misc_ctl_status; /* 0x17 - Miscellanies ctrl & status register*/
+ u8 boot_override; /* 0x18 - Boot override register */
+ u8 boot_config1; /* 0x19 - Boot config override register*/
+ u8 boot_config2; /* 0x1A - Boot config override register*/
+} cpld_data_t;
+
+
+/* Pointer to the CPLD register set */
+
+u8 cpld_read(unsigned int reg);
+void cpld_write(unsigned int reg, u8 value);
+
+#define CPLD_READ(reg) cpld_read(offsetof(struct cpld_data, reg))
+#define CPLD_WRITE(reg, value)\
+ cpld_write(offsetof(struct cpld_data, reg), value)
+
+/* CPLD on IFC */
+#define CPLD_LBMAP_MASK 0x3F
+#define CPLD_BANK_SEL_MASK 0x07
+#define CPLD_BANK_OVERRIDE 0x40
+#define CPLD_LBMAP_ALTBANK 0x44 /* BANK OR | BANK 4 */
+#define CPLD_LBMAP_DFLTBANK 0x40 /* BANK OR | BANK 0 */
+#define CPLD_LBMAP_RESET 0xFF
+#define CPLD_LBMAP_SHIFT 0x03
+#define CPLD_BOOT_SEL 0x80
diff --git a/board/freescale/t102xrdb/ddr.c b/board/freescale/t102xrdb/ddr.c
new file mode 100644
index 0000000..a20330b
--- /dev/null
+++ b/board/freescale/t102xrdb/ddr.c
@@ -0,0 +1,154 @@
+/*
+ * Copyright 2014 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <i2c.h>
+#include <hwconfig.h>
+#include <asm/mmu.h>
+#include <fsl_ddr_sdram.h>
+#include <fsl_ddr_dimm_params.h>
+#include <asm/fsl_law.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+struct board_specific_parameters {
+ u32 n_ranks;
+ u32 datarate_mhz_high;
+ u32 rank_gb;
+ u32 clk_adjust;
+ u32 wrlvl_start;
+ u32 wrlvl_ctl_2;
+ u32 wrlvl_ctl_3;
+};
+
+/*
+ * datarate_mhz_high values need to be in ascending order
+ */
+static const struct board_specific_parameters udimm0[] = {
+ /*
+ * memory controller 0
+ * num| hi| rank| clk| wrlvl | wrlvl | wrlvl |
+ * ranks| mhz| GB |adjst| start | ctl2 | ctl3 |
+ */
+ {2, 833, 0, 4, 6, 0x06060607, 0x08080807,},
+ {2, 1350, 0, 4, 7, 0x0708080A, 0x0A0B0C09,},
+ {2, 1666, 0, 4, 7, 0x0808090B, 0x0C0D0E0A,},
+ {1, 833, 0, 4, 6, 0x06060607, 0x08080807,},
+ {1, 1350, 0, 4, 7, 0x0708080A, 0x0A0B0C09,},
+ {1, 1666, 0, 4, 7, 0x0808090B, 0x0C0D0E0A,},
+ {}
+};
+
+static const struct board_specific_parameters *udimms[] = {
+ udimm0,
+};
+
+void fsl_ddr_board_options(memctl_options_t *popts,
+ dimm_params_t *pdimm,
+ unsigned int ctrl_num)
+{
+ const struct board_specific_parameters *pbsp, *pbsp_highest = NULL;
+ ulong ddr_freq;
+ struct cpu_type *cpu = gd->arch.cpu;
+
+ if (ctrl_num > 1) {
+ printf("Not supported controller number %d\n", ctrl_num);
+ return;
+ }
+ if (!pdimm->n_ranks)
+ return;
+
+ pbsp = udimms[0];
+
+ /* Get clk_adjust according to the board ddr freqency and n_banks
+ * specified in board_specific_parameters table.
+ */
+ ddr_freq = get_ddr_freq(0) / 1000000;
+ while (pbsp->datarate_mhz_high) {
+ if (pbsp->n_ranks == pdimm->n_ranks &&
+ (pdimm->rank_density >> 30) >= pbsp->rank_gb) {
+ if (ddr_freq <= pbsp->datarate_mhz_high) {
+ popts->clk_adjust = pbsp->clk_adjust;
+ popts->wrlvl_start = pbsp->wrlvl_start;
+ popts->wrlvl_ctl_2 = pbsp->wrlvl_ctl_2;
+ popts->wrlvl_ctl_3 = pbsp->wrlvl_ctl_3;
+ goto found;
+ }
+ pbsp_highest = pbsp;
+ }
+ pbsp++;
+ }
+
+ if (pbsp_highest) {
+ printf("Error: board specific timing not found\n");
+ printf("for data rate %lu MT/s\n", ddr_freq);
+ printf("Trying to use the highest speed (%u) parameters\n",
+ pbsp_highest->datarate_mhz_high);
+ popts->clk_adjust = pbsp_highest->clk_adjust;
+ popts->wrlvl_start = pbsp_highest->wrlvl_start;
+ popts->wrlvl_ctl_2 = pbsp->wrlvl_ctl_2;
+ popts->wrlvl_ctl_3 = pbsp->wrlvl_ctl_3;
+ } else {
+ panic("DIMM is not supported by this board");
+ }
+found:
+ debug("Found timing match: n_ranks %d, data rate %d, rank_gb %d\n",
+ pbsp->n_ranks, pbsp->datarate_mhz_high, pbsp->rank_gb);
+ debug("\tclk_adjust %d, wrlvl_start %d, wrlvl_ctrl_2 0x%x, ",
+ pbsp->clk_adjust, pbsp->wrlvl_start, pbsp->wrlvl_ctl_2);
+ debug("wrlvl_ctrl_3 0x%x\n", pbsp->wrlvl_ctl_3);
+
+ /*
+ * Factors to consider for half-strength driver enable:
+ * - number of DIMMs installed
+ */
+ popts->half_strength_driver_enable = 0;
+ /*
+ * Write leveling override
+ */
+ popts->wrlvl_override = 1;
+ popts->wrlvl_sample = 0xf;
+
+ /*
+ * rtt and rtt_wr override
+ */
+ popts->rtt_override = 0;
+
+ /* Enable ZQ calibration */
+ popts->zq_en = 1;
+
+ /* DHC_EN =1, ODT = 75 Ohm */
+ popts->ddr_cdr1 = DDR_CDR1_DHC_EN | DDR_CDR1_ODT(DDR_CDR_ODT_OFF);
+ popts->ddr_cdr2 = DDR_CDR2_ODT(DDR_CDR_ODT_OFF);
+
+ /* T1023 supports max DDR bus 32bit width, T1024 supports DDR 64bit,
+ * force DDR bus width to 32bit for T1023
+ */
+ if (cpu->soc_ver == SVR_T1023)
+ popts->data_bus_width = DDR_DATA_BUS_WIDTH_32;
+
+#ifdef CONFIG_FORCE_DDR_DATA_BUS_WIDTH_32
+ /* for DDR bus 32bit test on T1024 */
+ popts->data_bus_width = DDR_DATA_BUS_WIDTH_32;
+#endif
+}
+
+phys_size_t initdram(int board_type)
+{
+ phys_size_t dram_size;
+
+#if defined(CONFIG_SPL_BUILD) || !defined(CONFIG_RAMBOOT_PBL)
+ puts("Initializing....using SPD\n");
+
+ dram_size = fsl_ddr_sdram();
+ dram_size = setup_ddr_tlbs(dram_size / 0x100000);
+ dram_size *= 0x100000;
+#else
+ /* DDR has been initialised by first stage boot loader */
+ dram_size = fsl_ddr_sdram_size();
+#endif
+ return dram_size;
+}
diff --git a/board/freescale/t102xrdb/eth_t102xrdb.c b/board/freescale/t102xrdb/eth_t102xrdb.c
new file mode 100644
index 0000000..2e400c4
--- /dev/null
+++ b/board/freescale/t102xrdb/eth_t102xrdb.c
@@ -0,0 +1,100 @@
+/*
+ * Copyright 2014 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <command.h>
+#include <netdev.h>
+#include <asm/mmu.h>
+#include <asm/processor.h>
+#include <asm/immap_85xx.h>
+#include <asm/fsl_law.h>
+#include <asm/fsl_serdes.h>
+#include <asm/fsl_portals.h>
+#include <asm/fsl_liodn.h>
+#include <malloc.h>
+#include <fm_eth.h>
+#include <fsl_mdio.h>
+#include <miiphy.h>
+#include <phy.h>
+#include <asm/fsl_dtsec.h>
+#include <asm/fsl_serdes.h>
+
+int board_eth_init(bd_t *bis)
+{
+#if defined(CONFIG_FMAN_ENET)
+ int i, interface;
+ struct memac_mdio_info dtsec_mdio_info;
+ struct memac_mdio_info tgec_mdio_info;
+ struct mii_dev *dev;
+ ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
+ u32 srds_s1;
+
+ srds_s1 = in_be32(&gur->rcwsr[4]) &
+ FSL_CORENET2_RCWSR4_SRDS1_PRTCL;
+ srds_s1 >>= FSL_CORENET2_RCWSR4_SRDS1_PRTCL_SHIFT;
+
+ dtsec_mdio_info.regs =
+ (struct memac_mdio_controller *)CONFIG_SYS_FM1_DTSEC_MDIO_ADDR;
+
+ dtsec_mdio_info.name = DEFAULT_FM_MDIO_NAME;
+
+ /* Register the 1G MDIO bus */
+ fm_memac_mdio_init(bis, &dtsec_mdio_info);
+
+ tgec_mdio_info.regs =
+ (struct memac_mdio_controller *)CONFIG_SYS_FM1_TGEC_MDIO_ADDR;
+ tgec_mdio_info.name = DEFAULT_FM_TGEC_MDIO_NAME;
+
+ /* Register the 10G MDIO bus */
+ fm_memac_mdio_init(bis, &tgec_mdio_info);
+
+ /* Set the two on-board RGMII PHY address */
+ fm_info_set_phy_address(FM1_DTSEC3, RGMII_PHY2_ADDR);
+ fm_info_set_phy_address(FM1_DTSEC4, RGMII_PHY1_ADDR);
+
+ switch (srds_s1) {
+ case 0x95:
+ /* 10G XFI with Aquantia PHY */
+ fm_info_set_phy_address(FM1_10GEC1, FM1_10GEC1_PHY_ADDR);
+ break;
+ default:
+ printf("SerDes protocol 0x%x is not supported on T102xRDB\n",
+ srds_s1);
+ break;
+ }
+
+ for (i = FM1_DTSEC1; i < FM1_DTSEC1 + CONFIG_SYS_NUM_FM1_DTSEC; i++) {
+ interface = fm_info_get_enet_if(i);
+ switch (interface) {
+ case PHY_INTERFACE_MODE_RGMII:
+ dev = miiphy_get_dev_by_name(DEFAULT_FM_MDIO_NAME);
+ fm_info_set_mdio(i, dev);
+ break;
+ default:
+ break;
+ }
+ }
+
+ for (i = FM1_10GEC1; i < FM1_10GEC1 + CONFIG_SYS_NUM_FM1_10GEC; i++) {
+ switch (fm_info_get_enet_if(i)) {
+ case PHY_INTERFACE_MODE_XGMII:
+ dev = miiphy_get_dev_by_name(DEFAULT_FM_TGEC_MDIO_NAME);
+ fm_info_set_mdio(i, dev);
+ break;
+ default:
+ break;
+ }
+ }
+
+ cpu_eth_init(bis);
+#endif /* CONFIG_FMAN_ENET */
+
+ return pci_eth_init(bis);
+}
+
+void fdt_fixup_board_enet(void *fdt)
+{
+}
diff --git a/board/freescale/t102xrdb/law.c b/board/freescale/t102xrdb/law.c
new file mode 100644
index 0000000..1c9235f
--- /dev/null
+++ b/board/freescale/t102xrdb/law.c
@@ -0,0 +1,32 @@
+/*
+ * Copyright 2014 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <asm/fsl_law.h>
+#include <asm/mmu.h>
+
+struct law_entry law_table[] = {
+#ifndef CONFIG_SYS_NO_FLASH
+ SET_LAW(CONFIG_SYS_FLASH_BASE_PHYS, LAW_SIZE_256M, LAW_TRGT_IF_IFC),
+#endif
+#ifdef CONFIG_SYS_BMAN_MEM_PHYS
+ SET_LAW(CONFIG_SYS_BMAN_MEM_PHYS, LAW_SIZE_32M, LAW_TRGT_IF_BMAN),
+#endif
+#ifdef CONFIG_SYS_QMAN_MEM_PHYS
+ SET_LAW(CONFIG_SYS_QMAN_MEM_PHYS, LAW_SIZE_32M, LAW_TRGT_IF_QMAN),
+#endif
+#ifdef CONFIG_SYS_CPLD_BASE_PHYS
+ SET_LAW(CONFIG_SYS_CPLD_BASE_PHYS, LAW_SIZE_4K, LAW_TRGT_IF_IFC),
+#endif
+#ifdef CONFIG_SYS_DCSRBAR_PHYS
+ SET_LAW(CONFIG_SYS_DCSRBAR_PHYS, LAW_SIZE_4M, LAW_TRGT_IF_DCSR),
+#endif
+#ifdef CONFIG_SYS_NAND_BASE_PHYS
+ SET_LAW(CONFIG_SYS_NAND_BASE_PHYS, LAW_SIZE_64K, LAW_TRGT_IF_IFC),
+#endif
+};
+
+int num_law_entries = ARRAY_SIZE(law_table);
diff --git a/board/freescale/t102xrdb/pci.c b/board/freescale/t102xrdb/pci.c
new file mode 100644
index 0000000..ba7041a
--- /dev/null
+++ b/board/freescale/t102xrdb/pci.c
@@ -0,0 +1,23 @@
+/*
+ * Copyright 2007-2014 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <command.h>
+#include <pci.h>
+#include <asm/fsl_pci.h>
+#include <libfdt.h>
+#include <fdt_support.h>
+#include <asm/fsl_serdes.h>
+
+void pci_init_board(void)
+{
+ fsl_pcie_init_board(0);
+}
+
+void pci_of_setup(void *blob, bd_t *bd)
+{
+ FT_FSL_PCI_SETUP;
+}
diff --git a/board/freescale/t102xrdb/spl.c b/board/freescale/t102xrdb/spl.c
new file mode 100644
index 0000000..dd2dec4
--- /dev/null
+++ b/board/freescale/t102xrdb/spl.c
@@ -0,0 +1,107 @@
+/* Copyright 2014 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <malloc.h>
+#include <ns16550.h>
+#include <nand.h>
+#include <i2c.h>
+#include <mmc.h>
+#include <fsl_esdhc.h>
+#include <spi_flash.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+phys_size_t get_effective_memsize(void)
+{
+ return CONFIG_SYS_L3_SIZE;
+}
+
+unsigned long get_board_sys_clk(void)
+{
+ return CONFIG_SYS_CLK_FREQ;
+}
+
+unsigned long get_board_ddr_clk(void)
+{
+ return CONFIG_DDR_CLK_FREQ;
+}
+
+void board_init_f(ulong bootflag)
+{
+ u32 plat_ratio, sys_clk, ccb_clk;
+ ccsr_gur_t *gur = (void *)CONFIG_SYS_MPC85xx_GUTS_ADDR;
+
+ /* Memcpy existing GD at CONFIG_SPL_GD_ADDR */
+ memcpy((void *)CONFIG_SPL_GD_ADDR, (void *)gd, sizeof(gd_t));
+
+ /* Update GD pointer */
+ gd = (gd_t *)(CONFIG_SPL_GD_ADDR);
+
+ console_init_f();
+
+ /* initialize selected port with appropriate baud rate */
+ sys_clk = get_board_sys_clk();
+ plat_ratio = (in_be32(&gur->rcwsr[0]) >> 25) & 0x1f;
+ ccb_clk = sys_clk * plat_ratio / 2;
+
+ NS16550_init((NS16550_t)CONFIG_SYS_NS16550_COM1,
+ ccb_clk / 16 / CONFIG_BAUDRATE);
+
+#if defined(CONFIG_SPL_MMC_BOOT)
+ puts("\nSD boot...\n");
+#elif defined(CONFIG_SPL_SPI_BOOT)
+ puts("\nSPI boot...\n");
+#elif defined(CONFIG_SPL_NAND_BOOT)
+ puts("\nNAND boot...\n");
+#endif
+
+ relocate_code(CONFIG_SPL_RELOC_STACK, (gd_t *)CONFIG_SPL_GD_ADDR, 0x0);
+}
+
+void board_init_r(gd_t *gd, ulong dest_addr)
+{
+ bd_t *bd;
+
+ bd = (bd_t *)(gd + sizeof(gd_t));
+ memset(bd, 0, sizeof(bd_t));
+ gd->bd = bd;
+ bd->bi_memstart = CONFIG_SYS_INIT_L3_ADDR;
+ bd->bi_memsize = CONFIG_SYS_L3_SIZE;
+
+ probecpu();
+ get_clocks();
+ mem_malloc_init(CONFIG_SPL_RELOC_MALLOC_ADDR,
+ CONFIG_SPL_RELOC_MALLOC_SIZE);
+
+#ifdef CONFIG_SPL_NAND_BOOT
+ nand_spl_load_image(CONFIG_ENV_OFFSET, CONFIG_ENV_SIZE,
+ (uchar *)CONFIG_ENV_ADDR);
+#endif
+#ifdef CONFIG_SPL_MMC_BOOT
+ mmc_initialize(bd);
+ mmc_spl_load_image(CONFIG_ENV_OFFSET, CONFIG_ENV_SIZE,
+ (uchar *)CONFIG_ENV_ADDR);
+#endif
+#ifdef CONFIG_SPL_SPI_BOOT
+ spi_spl_load_image(CONFIG_ENV_OFFSET, CONFIG_ENV_SIZE,
+ (uchar *)CONFIG_ENV_ADDR);
+#endif
+
+ gd->env_addr = (ulong)(CONFIG_ENV_ADDR);
+ gd->env_valid = 1;
+
+ i2c_init_all();
+
+ gd->ram_size = initdram(0);
+
+#ifdef CONFIG_SPL_MMC_BOOT
+ mmc_boot();
+#elif defined(CONFIG_SPL_SPI_BOOT)
+ spi_boot();
+#elif defined(CONFIG_SPL_NAND_BOOT)
+ nand_boot();
+#endif
+}
diff --git a/board/freescale/t102xrdb/t1024_pbi.cfg b/board/freescale/t102xrdb/t1024_pbi.cfg
new file mode 100644
index 0000000..7b9e9b0
--- /dev/null
+++ b/board/freescale/t102xrdb/t1024_pbi.cfg
@@ -0,0 +1,26 @@
+#PBI commands
+#Initialize CPC1
+09010000 00200400
+09138000 00000000
+091380c0 00000100
+#Configure CPC1 as 256KB SRAM
+09010100 00000000
+09010104 fffc0007
+09010f00 08000000
+09010000 80000000
+#Configure LAW for CPC1
+09000cd0 00000000
+09000cd4 fffc0000
+09000cd8 81000011
+#Configure alternate space
+09000010 00000000
+09000014 ff000000
+09000018 81000000
+#Configure SPI controller
+09110000 80000403
+09110020 2d170008
+09110024 00100008
+09110028 00100008
+0911002c 00100008
+#Flush PBL data
+091380c0 000FFFFF
diff --git a/board/freescale/t102xrdb/t1024_rcw.cfg b/board/freescale/t102xrdb/t1024_rcw.cfg
new file mode 100644
index 0000000..cd6f906
--- /dev/null
+++ b/board/freescale/t102xrdb/t1024_rcw.cfg
@@ -0,0 +1,8 @@
+#PBL preamble and RCW header for T1024RDB
+aa55aa55 010e0100
+#SerDes Protocol: 0x95
+#Core/DDR: 1400Mhz/1600MT/s with single source clock
+0810000c 00000000 00000000 00000000
+4a800003 80000012 ec027000 21000000
+00000000 00000000 00000000 00030810
+00000000 0b005a08 00000000 00000006
diff --git a/board/freescale/t102xrdb/t102xrdb.c b/board/freescale/t102xrdb/t102xrdb.c
new file mode 100644
index 0000000..f5c438d
--- /dev/null
+++ b/board/freescale/t102xrdb/t102xrdb.c
@@ -0,0 +1,144 @@
+/*
+ * Copyright 2014 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <command.h>
+#include <i2c.h>
+#include <netdev.h>
+#include <linux/compiler.h>
+#include <asm/mmu.h>
+#include <asm/processor.h>
+#include <asm/immap_85xx.h>
+#include <asm/fsl_law.h>
+#include <asm/fsl_serdes.h>
+#include <asm/fsl_portals.h>
+#include <asm/fsl_liodn.h>
+#include <asm/mpc85xx_gpio.h>
+#include <fm_eth.h>
+#include "t102xrdb.h"
+#include "cpld.h"
+
+DECLARE_GLOBAL_DATA_PTR;
+
+int checkboard(void)
+{
+ struct cpu_type *cpu = gd->arch.cpu;
+ static const char *freq[3] = {"100.00MHZ", "125.00MHz", "156.25MHZ"};
+
+ printf("Board: %sRDB, ", cpu->name);
+ printf("Board rev: 0x%02x CPLD ver: 0x%02x, boot from ",
+ CPLD_READ(hw_ver), CPLD_READ(sw_ver));
+
+#ifdef CONFIG_SDCARD
+ puts("SD/MMC\n");
+#elif CONFIG_SPIFLASH
+ puts("SPI\n");
+#else
+ u8 reg;
+
+ reg = CPLD_READ(flash_csr);
+
+ if (reg & CPLD_BOOT_SEL) {
+ puts("NAND\n");
+ } else {
+ reg = ((reg & CPLD_LBMAP_MASK) >> CPLD_LBMAP_SHIFT);
+ printf("NOR vBank%d\n", reg);
+ }
+#endif
+
+ puts("SERDES Reference Clocks:\n");
+ printf("SD1_CLK1=%s, SD1_CLK2=%s\n", freq[2], freq[0]);
+
+ return 0;
+}
+
+int board_early_init_r(void)
+{
+#ifdef CONFIG_SYS_FLASH_BASE
+ const unsigned int flashbase = CONFIG_SYS_FLASH_BASE;
+ int flash_esel = find_tlb_idx((void *)flashbase, 1);
+ /*
+ * Remap Boot flash region to caching-inhibited
+ * so that flash can be erased properly.
+ */
+
+ /* Flush d-cache and invalidate i-cache of any FLASH data */
+ flush_dcache();
+ invalidate_icache();
+ if (flash_esel == -1) {
+ /* very unlikely unless something is messed up */
+ puts("Error: Could not find TLB for FLASH BASE\n");
+ flash_esel = 2; /* give our best effort to continue */
+ } else {
+ /* invalidate existing TLB entry for flash + promjet */
+ disable_tlb(flash_esel);
+ }
+
+ set_tlb(1, flashbase, CONFIG_SYS_FLASH_BASE_PHYS,
+ MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+ 0, flash_esel, BOOKE_PAGESZ_256M, 1);
+#endif
+
+ set_liodns();
+#ifdef CONFIG_SYS_DPAA_QBMAN
+ setup_portals();
+#endif
+
+ return 0;
+}
+
+unsigned long get_board_sys_clk(void)
+{
+ return CONFIG_SYS_CLK_FREQ;
+}
+
+unsigned long get_board_ddr_clk(void)
+{
+ return CONFIG_DDR_CLK_FREQ;
+}
+
+int misc_init_r(void)
+{
+ return 0;
+}
+
+int ft_board_setup(void *blob, bd_t *bd)
+{
+ phys_addr_t base;
+ phys_size_t size;
+
+ ft_cpu_setup(blob, bd);
+
+ base = getenv_bootm_low();
+ size = getenv_bootm_size();
+
+ fdt_fixup_memory(blob, (u64)base, (u64)size);
+
+#ifdef CONFIG_PCI
+ pci_of_setup(blob, bd);
+#endif
+
+ fdt_fixup_liodn(blob);
+ fdt_fixup_dr_usb(blob, bd);
+
+#ifdef CONFIG_SYS_DPAA_FMAN
+ fdt_fixup_fman_ethernet(blob);
+ fdt_fixup_board_enet(blob);
+#endif
+
+ return 0;
+}
+
+#ifdef CONFIG_DEEP_SLEEP
+void board_mem_sleep_setup(void)
+{
+ /* does not provide HW signals for power management */
+ CPLD_WRITE(misc_ctl_status, (CPLD_READ(misc_ctl_status) & ~0x40));
+ /* Disable MCKE isolation */
+ gpio_set_value(2, 0);
+ udelay(1);
+}
+#endif
diff --git a/board/freescale/t102xrdb/t102xrdb.h b/board/freescale/t102xrdb/t102xrdb.h
new file mode 100644
index 0000000..2f23579
--- /dev/null
+++ b/board/freescale/t102xrdb/t102xrdb.h
@@ -0,0 +1,13 @@
+/*
+ * Copyright 2014 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#ifndef __T1024_RDB_H__
+#define __T1024_RDB_H__
+
+void fdt_fixup_board_enet(void *blob);
+void pci_of_setup(void *blob, bd_t *bd);
+
+#endif
diff --git a/board/freescale/t102xrdb/tlb.c b/board/freescale/t102xrdb/tlb.c
new file mode 100644
index 0000000..8269b3d
--- /dev/null
+++ b/board/freescale/t102xrdb/tlb.c
@@ -0,0 +1,117 @@
+/*
+ * Copyright 2014 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <asm/mmu.h>
+
+struct fsl_e_tlb_entry tlb_table[] = {
+ /* TLB 0 - for temp stack in cache */
+ SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR,
+ CONFIG_SYS_INIT_RAM_ADDR_PHYS,
+ MAS3_SX|MAS3_SW|MAS3_SR, 0,
+ 0, 0, BOOKE_PAGESZ_4K, 0),
+ SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 4 * 1024,
+ CONFIG_SYS_INIT_RAM_ADDR_PHYS + 4 * 1024,
+ MAS3_SX|MAS3_SW|MAS3_SR, 0,
+ 0, 0, BOOKE_PAGESZ_4K, 0),
+ SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 8 * 1024,
+ CONFIG_SYS_INIT_RAM_ADDR_PHYS + 8 * 1024,
+ MAS3_SX|MAS3_SW|MAS3_SR, 0,
+ 0, 0, BOOKE_PAGESZ_4K, 0),
+ SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 12 * 1024,
+ CONFIG_SYS_INIT_RAM_ADDR_PHYS + 12 * 1024,
+ MAS3_SX|MAS3_SW|MAS3_SR, 0,
+ 0, 0, BOOKE_PAGESZ_4K, 0),
+
+ /* TLB 1 */
+ /* *I*** - Covers boot page */
+#if defined(CONFIG_SYS_RAMBOOT) && defined(CONFIG_SYS_INIT_L3_ADDR)
+ /*
+ * *I*G - L3SRAM. When L3 is used as 256K SRAM, the address of the
+ * SRAM is at 0xfffc0000, it covered the 0xfffff000.
+ */
+ SET_TLB_ENTRY(1, CONFIG_SYS_INIT_L3_ADDR, CONFIG_SYS_INIT_L3_ADDR,
+ MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+ 0, 0, BOOKE_PAGESZ_256K, 1),
+#else
+ SET_TLB_ENTRY(1, 0xfffff000, 0xfffff000,
+ MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+ 0, 0, BOOKE_PAGESZ_4K, 1),
+#endif
+
+ /* *I*G* - CCSRBAR */
+ SET_TLB_ENTRY(1, CONFIG_SYS_CCSRBAR, CONFIG_SYS_CCSRBAR_PHYS,
+ MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+ 0, 1, BOOKE_PAGESZ_16M, 1),
+
+ /* *I*G* - Flash, localbus */
+ /* This will be changed to *I*G* after relocation to RAM. */
+ SET_TLB_ENTRY(1, CONFIG_SYS_FLASH_BASE, CONFIG_SYS_FLASH_BASE_PHYS,
+ MAS3_SX|MAS3_SR, MAS2_W|MAS2_G,
+ 0, 2, BOOKE_PAGESZ_256M, 1),
+
+#ifndef CONFIG_SPL_BUILD
+ /* *I*G* - PCI */
+ SET_TLB_ENTRY(1, CONFIG_SYS_PCIE1_MEM_VIRT, CONFIG_SYS_PCIE1_MEM_PHYS,
+ MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+ 0, 3, BOOKE_PAGESZ_1G, 1),
+
+ /* *I*G* - PCI I/O */
+ SET_TLB_ENTRY(1, CONFIG_SYS_PCIE1_IO_VIRT, CONFIG_SYS_PCIE1_IO_PHYS,
+ MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+ 0, 4, BOOKE_PAGESZ_256K, 1),
+
+ /* Bman/Qman */
+#ifdef CONFIG_SYS_BMAN_MEM_PHYS
+ SET_TLB_ENTRY(1, CONFIG_SYS_BMAN_MEM_BASE, CONFIG_SYS_BMAN_MEM_PHYS,
+ MAS3_SX|MAS3_SW|MAS3_SR, 0,
+ 0, 5, BOOKE_PAGESZ_16M, 1),
+ SET_TLB_ENTRY(1, CONFIG_SYS_BMAN_MEM_BASE + 0x01000000,
+ CONFIG_SYS_BMAN_MEM_PHYS + 0x01000000,
+ MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+ 0, 6, BOOKE_PAGESZ_16M, 1),
+#endif
+#ifdef CONFIG_SYS_QMAN_MEM_PHYS
+ SET_TLB_ENTRY(1, CONFIG_SYS_QMAN_MEM_BASE, CONFIG_SYS_QMAN_MEM_PHYS,
+ MAS3_SX|MAS3_SW|MAS3_SR, 0,
+ 0, 7, BOOKE_PAGESZ_16M, 1),
+ SET_TLB_ENTRY(1, CONFIG_SYS_QMAN_MEM_BASE + 0x01000000,
+ CONFIG_SYS_QMAN_MEM_PHYS + 0x01000000,
+ MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+ 0, 8, BOOKE_PAGESZ_16M, 1),
+#endif
+#endif
+#ifdef CONFIG_SYS_DCSRBAR_PHYS
+ SET_TLB_ENTRY(1, CONFIG_SYS_DCSRBAR, CONFIG_SYS_DCSRBAR_PHYS,
+ MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+ 0, 9, BOOKE_PAGESZ_4M, 1),
+#endif
+#ifdef CONFIG_SYS_NAND_BASE
+ SET_TLB_ENTRY(1, CONFIG_SYS_NAND_BASE, CONFIG_SYS_NAND_BASE_PHYS,
+ MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+ 0, 10, BOOKE_PAGESZ_64K, 1),
+#endif
+#ifdef CONFIG_SYS_CPLD_BASE
+ SET_TLB_ENTRY(1, CONFIG_SYS_CPLD_BASE, CONFIG_SYS_CPLD_BASE_PHYS,
+ MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+ 0, 11, BOOKE_PAGESZ_256K, 1),
+#endif
+
+#if defined(CONFIG_RAMBOOT_PBL) && !defined(CONFIG_SPL_BUILD)
+ SET_TLB_ENTRY(1, CONFIG_SYS_DDR_SDRAM_BASE, CONFIG_SYS_DDR_SDRAM_BASE,
+ MAS3_SX|MAS3_SW|MAS3_SR, 0,
+ 0, 12, BOOKE_PAGESZ_1G, 1),
+ SET_TLB_ENTRY(1, CONFIG_SYS_DDR_SDRAM_BASE + 0x40000000,
+ CONFIG_SYS_DDR_SDRAM_BASE + 0x40000000,
+ MAS3_SX|MAS3_SW|MAS3_SR, 0,
+ 0, 13, BOOKE_PAGESZ_1G, 1)
+#endif
+ /* entry 14 and 15 has been used hard coded, they will be disabled
+ * in cpu_init_f, so if needed more, will use entry 16 later.
+ */
+};
+
+int num_tlb_entries = ARRAY_SIZE(tlb_table);
diff --git a/board/freescale/t104xrdb/spl.c b/board/freescale/t104xrdb/spl.c
index 3822a37..e394b12 100644
--- a/board/freescale/t104xrdb/spl.c
+++ b/board/freescale/t104xrdb/spl.c
@@ -34,20 +34,26 @@
void board_init_f(ulong bootflag)
{
u32 plat_ratio, sys_clk, uart_clk;
-#ifdef CONFIG_SPL_NAND_BOOT
+#if defined(CONFIG_SPL_NAND_BOOT) && defined(CONFIG_A008044_WORKAROUND)
u32 porsr1, pinctl;
+ u32 svr = get_svr();
#endif
ccsr_gur_t *gur = (void *)CONFIG_SYS_MPC85xx_GUTS_ADDR;
-#ifdef CONFIG_SPL_NAND_BOOT
- /*
- * There is T1040 SoC issue where NOR, FPGA are inaccessible during
- * NAND boot because IFC signals > IFC_AD7 are not enabled.
- * This workaround changes RCW source to make all signals enabled.
- */
- porsr1 = in_be32(&gur->porsr1);
- pinctl = ((porsr1 & ~(FSL_CORENET_CCSR_PORSR1_RCW_MASK)) | 0x24800000);
- out_be32((unsigned int *)(CONFIG_SYS_DCSRBAR + 0x20000), pinctl);
+#if defined(CONFIG_SPL_NAND_BOOT) && defined(CONFIG_A008044_WORKAROUND)
+ if (IS_SVR_REV(svr, 1, 0)) {
+ /*
+ * There is T1040 SoC issue where NOR, FPGA are inaccessible
+ * during NAND boot because IFC signals > IFC_AD7 are not
+ * enabled. This workaround changes RCW source to make all
+ * signals enabled.
+ */
+ porsr1 = in_be32(&gur->porsr1);
+ pinctl = ((porsr1 & ~(FSL_CORENET_CCSR_PORSR1_RCW_MASK))
+ | 0x24800000);
+ out_be32((unsigned int *)(CONFIG_SYS_DCSRBAR + 0x20000),
+ pinctl);
+ }
#endif
/* Memcpy existing GD at CONFIG_SPL_GD_ADDR */
diff --git a/board/freescale/t208xqds/ddr.h b/board/freescale/t208xqds/ddr.h
index ed52fef6..9c26fdf 100644
--- a/board/freescale/t208xqds/ddr.h
+++ b/board/freescale/t208xqds/ddr.h
@@ -28,17 +28,16 @@
* num| hi| rank| clk| wrlvl | wrlvl | wrlvl |
* ranks| mhz| GB |adjst| start | ctl2 | ctl3 |
*/
- {2, 1200, 0, 5, 7, 0x0808090a, 0x0b0c0c0a},
- {2, 1500, 0, 5, 6, 0x07070809, 0x0a0b0b09},
- {2, 1600, 0, 5, 8, 0x090b0b0d, 0x0d0e0f0b},
- {2, 1700, 0, 4, 7, 0x080a0a0c, 0x0c0d0e0a},
- {2, 1900, 0, 5, 9, 0x0a0b0c0e, 0x0f10120c},
- {2, 2140, 0, 4, 8, 0x090a0b0d, 0x0e0f110b},
+ {2, 1200, 0, 5, 7, 0x0708090a, 0x0b0c0d09},
+ {2, 1400, 0, 5, 7, 0x08090a0c, 0x0d0e0f0a},
+ {2, 1700, 0, 5, 8, 0x090a0b0c, 0x0e10110c},
+ {2, 1900, 0, 5, 8, 0x090b0c0f, 0x1012130d},
+ {2, 2140, 0, 5, 8, 0x090b0c0f, 0x1012130d},
{1, 1200, 0, 5, 7, 0x0808090a, 0x0b0c0c0a},
{1, 1500, 0, 5, 6, 0x07070809, 0x0a0b0b09},
{1, 1600, 0, 5, 8, 0x090b0b0d, 0x0d0e0f0b},
- {1, 1700, 0, 4, 7, 0x080a0a0c, 0x0c0d0e0a},
- {1, 1900, 0, 5, 9, 0x0a0b0c0e, 0x0f10120c},
+ {1, 1700, 0, 4, 8, 0x080a0a0c, 0x0c0d0e0a},
+ {1, 1900, 0, 5, 8, 0x090a0c0d, 0x0e0f110c},
{1, 2140, 0, 4, 8, 0x090a0b0d, 0x0e0f110b},
{}
};
diff --git a/board/freescale/t208xqds/t2080_rcw.cfg b/board/freescale/t208xqds/t2080_rcw.cfg
index 972dedc..52a1652 100644
--- a/board/freescale/t208xqds/t2080_rcw.cfg
+++ b/board/freescale/t208xqds/t2080_rcw.cfg
@@ -1,8 +1,16 @@
#PBL preamble and RCW header
aa55aa55 010e0100
-#SerDes Protocol: 0x66_0x16
-#Core/DDR: 1533Mhz/2133MT/s
-12100017 15000000 00000000 00000000
-66150002 00008400 e8104000 c1000000
+
+#For T2080 v1.0
+#SerDes=0x66_0x16, Core=1533MHz, DDR=2133MT/s
+#12100017 15000000 00000000 00000000
+#66150002 00008400 e8104000 c1000000
+#00000000 00000000 00000000 000307fc
+#00000000 00000000 00000000 00000004
+
+#For T2080 v1.1
+#SerDes=0x66_0x15, Core=1800MHz, DDR=1867MT/s
+0c070012 0e000000 00000000 00000000
+66150002 00000000 e8104000 c1000000
00000000 00000000 00000000 000307fc
00000000 00000000 00000000 00000004
diff --git a/board/freescale/t208xqds/t208xqds.c b/board/freescale/t208xqds/t208xqds.c
index 5c470c3..7c89cd5 100644
--- a/board/freescale/t208xqds/t208xqds.c
+++ b/board/freescale/t208xqds/t208xqds.c
@@ -20,6 +20,7 @@
#include "../common/qixis.h"
#include "../common/vsc3316_3308.h"
+#include "../common/vid.h"
#include "t208xqds.h"
#include "t208xqds_qixis.h"
@@ -86,6 +87,11 @@
return 0;
}
+int i2c_multiplexer_select_vid_channel(u8 channel)
+{
+ return select_i2c_ch_pca9547(channel);
+}
+
int brd_mux_lane_to_slot(void)
{
ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
@@ -358,6 +364,13 @@
/* Disable remote I2C connection to qixis fpga */
QIXIS_WRITE(brdcfg[5], QIXIS_READ(brdcfg[5]) & ~BRDCFG5_IRE);
+ /*
+ * Adjust core voltage according to voltage ID
+ * This function changes I2C mux to channel 2.
+ */
+ if (adjust_vdd(0))
+ printf("Warning: Adjusting core voltage failed.\n");
+
brd_mux_lane_to_slot();
select_i2c_ch_pca9547(I2C_MUX_CH_DEFAULT);
diff --git a/board/freescale/t208xrdb/t2080_rcw.cfg b/board/freescale/t208xrdb/t2080_rcw.cfg
index 15e1bf4..59025ea 100644
--- a/board/freescale/t208xrdb/t2080_rcw.cfg
+++ b/board/freescale/t208xrdb/t2080_rcw.cfg
@@ -1,8 +1,16 @@
-#PBL preamble and RCW header for T2080RDB
+#PBL preamble and RCW header
aa55aa55 010e0100
-#SerDes Protocol: 0x66_0x16
-#Core/DDR: 1533Mhz/1600MT/s
-120c0017 15000000 00000000 00000000
-66150002 00008400 ec104000 c1000000
-00000000 00000000 00000000 000307fc
+
+#For T2080 v1.0
+#SerDes=0x66_0x16, Core=1533MHz, DDR=1600MT/s
+#120c0017 15000000 00000000 00000000
+#66150002 00008400 ec104000 c1000000
+#00000000 00000000 00000000 000307fc
+#00000000 00000000 00000000 00000004
+
+#For T2080 v1.1
+#SerDes=0x66_0x15, Core:1800MHz, DDR:1600MT/s
+1206001b 15000000 00000000 00000000
+66150002 00000000 e8104000 c1000000
+00800000 00000000 00000000 000307fc
00000000 00000000 00000000 00000004
diff --git a/board/keymile/km82xx/km82xx.c b/board/keymile/km82xx/km82xx.c
index e200935..bf84676 100644
--- a/board/keymile/km82xx/km82xx.c
+++ b/board/keymile/km82xx/km82xx.c
@@ -300,11 +300,9 @@
out_8(&memctl->memc_psrt, CONFIG_SYS_PSRT);
out_be16(&memctl->memc_mptpr, CONFIG_SYS_MPTPR);
-#ifndef CONFIG_SYS_RAMBOOT
/* 60x SDRAM setup:
*/
psize = probe_sdram(memctl);
-#endif /* CONFIG_SYS_RAMBOOT */
icache_enable();
diff --git a/board/muas3001/muas3001.c b/board/muas3001/muas3001.c
index 529a58c..e0c4dba 100644
--- a/board/muas3001/muas3001.c
+++ b/board/muas3001/muas3001.c
@@ -243,14 +243,11 @@
volatile immap_t *immap = (immap_t *) CONFIG_SYS_IMMR;
volatile memctl8260_t *memctl = &immap->im_memctl;
long psize;
-#ifndef CONFIG_SYS_RAMBOOT
long sizelittle, sizebig;
-#endif
memctl->memc_psrt = CONFIG_SYS_PSRT;
memctl->memc_mptpr = CONFIG_SYS_MPTPR;
-#ifndef CONFIG_SYS_RAMBOOT
/* 60x SDRAM setup:
*/
sizelittle = try_init (memctl, CONFIG_SYS_PSDMR_LITTLE, CONFIG_SYS_OR1_LITTLE,
@@ -263,7 +260,6 @@
psize = try_init (memctl, CONFIG_SYS_PSDMR_LITTLE, CONFIG_SYS_OR1_LITTLE,
(uchar *) CONFIG_SYS_SDRAM_BASE);
}
-#endif /* CONFIG_SYS_RAMBOOT */
icache_enable ();
diff --git a/common/Makefile b/common/Makefile
index 9c47e20..c668a2f 100644
--- a/common/Makefile
+++ b/common/Makefile
@@ -8,22 +8,12 @@
# core
ifndef CONFIG_SPL_BUILD
obj-y += main.o
-obj-y += command.o
obj-y += exports.o
obj-y += hash.o
ifdef CONFIG_SYS_HUSH_PARSER
obj-y += cli_hush.o
endif
-# We always have this since drivers/ddr/fs/interactive.c needs it
-obj-y += cli_simple.o
-
-obj-y += cli.o
-obj-y += cli_readline.o
-obj-y += s_record.o
-obj-y += xyzModem.o
-obj-y += cmd_disk.o
-
# This option is not just y/n - it can have a numeric value
ifdef CONFIG_BOOTDELAY
obj-y += autoboot.o
@@ -272,4 +262,14 @@
obj-$(CONFIG_CMD_BLOB) += cmd_blob.o
+# We always have this since drivers/ddr/fs/interactive.c needs it
+obj-y += cli_simple.o
+
+obj-y += cli.o
+obj-y += cli_readline.o
+obj-y += command.o
+obj-y += s_record.o
+obj-y += xyzModem.o
+obj-y += cmd_disk.o
+
CFLAGS_env_embedded.o := -Wa,--no-warn -DENV_CRC=$(shell tools/envcrc 2>/dev/null)
diff --git a/configs/T1024QDS_D4_SECURE_BOOT_defconfig b/configs/T1024QDS_D4_SECURE_BOOT_defconfig
new file mode 100644
index 0000000..d86ae05
--- /dev/null
+++ b/configs/T1024QDS_D4_SECURE_BOOT_defconfig
@@ -0,0 +1,4 @@
+CONFIG_SYS_EXTRA_OPTIONS="PPC_T1024,SYS_FSL_DDR4,SECURE_BOOT"
+CONFIG_PPC=y
+CONFIG_MPC85xx=y
+CONFIG_TARGET_T102XQDS=y
diff --git a/configs/T1024QDS_NAND_defconfig b/configs/T1024QDS_NAND_defconfig
new file mode 100644
index 0000000..acbbe43
--- /dev/null
+++ b/configs/T1024QDS_NAND_defconfig
@@ -0,0 +1,5 @@
+CONFIG_SPL=y
+CONFIG_SYS_EXTRA_OPTIONS="PPC_T1024,RAMBOOT_PBL,SPL_FSL_PBL,NAND"
++S:CONFIG_PPC=y
++S:CONFIG_MPC85xx=y
++S:CONFIG_TARGET_T102XQDS=y
diff --git a/configs/T1024QDS_SDCARD_defconfig b/configs/T1024QDS_SDCARD_defconfig
new file mode 100644
index 0000000..82c6e19
--- /dev/null
+++ b/configs/T1024QDS_SDCARD_defconfig
@@ -0,0 +1,5 @@
+CONFIG_SPL=y
+CONFIG_SYS_EXTRA_OPTIONS="PPC_T1024,RAMBOOT_PBL,SPL_FSL_PBL,SDCARD"
++S:CONFIG_PPC=y
++S:CONFIG_MPC85xx=y
++S:CONFIG_TARGET_T102XQDS=y
diff --git a/configs/T1024QDS_SECURE_BOOT_defconfig b/configs/T1024QDS_SECURE_BOOT_defconfig
new file mode 100644
index 0000000..b932619
--- /dev/null
+++ b/configs/T1024QDS_SECURE_BOOT_defconfig
@@ -0,0 +1,4 @@
+CONFIG_SYS_EXTRA_OPTIONS="PPC_T1024,SECURE_BOOT"
+CONFIG_PPC=y
+CONFIG_MPC85xx=y
+CONFIG_TARGET_T102XQDS=y
diff --git a/configs/T1024QDS_SPIFLASH_defconfig b/configs/T1024QDS_SPIFLASH_defconfig
new file mode 100644
index 0000000..52aeac7
--- /dev/null
+++ b/configs/T1024QDS_SPIFLASH_defconfig
@@ -0,0 +1,5 @@
+CONFIG_SPL=y
+CONFIG_SYS_EXTRA_OPTIONS="PPC_T1024,RAMBOOT_PBL,SPL_FSL_PBL,SPIFLASH"
++S:CONFIG_PPC=y
++S:CONFIG_MPC85xx=y
++S:CONFIG_TARGET_T102XQDS=y
diff --git a/configs/T1024RDB_NAND_defconfig b/configs/T1024RDB_NAND_defconfig
new file mode 100644
index 0000000..73d14ab
--- /dev/null
+++ b/configs/T1024RDB_NAND_defconfig
@@ -0,0 +1,5 @@
+CONFIG_SPL=y
+CONFIG_SYS_EXTRA_OPTIONS="PPC_T1024,RAMBOOT_PBL,SPL_FSL_PBL,NAND"
++S:CONFIG_PPC=y
++S:CONFIG_MPC85xx=y
++S:CONFIG_TARGET_T102XRDB=y
diff --git a/configs/T1024RDB_SDCARD_defconfig b/configs/T1024RDB_SDCARD_defconfig
new file mode 100644
index 0000000..3599f1d
--- /dev/null
+++ b/configs/T1024RDB_SDCARD_defconfig
@@ -0,0 +1,5 @@
+CONFIG_SPL=y
+CONFIG_SYS_EXTRA_OPTIONS="PPC_T1024,RAMBOOT_PBL,SPL_FSL_PBL,SDCARD"
++S:CONFIG_PPC=y
++S:CONFIG_MPC85xx=y
++S:CONFIG_TARGET_T102XRDB=y
diff --git a/configs/T1024RDB_SECURE_BOOT_defconfig b/configs/T1024RDB_SECURE_BOOT_defconfig
new file mode 100644
index 0000000..8377260
--- /dev/null
+++ b/configs/T1024RDB_SECURE_BOOT_defconfig
@@ -0,0 +1,4 @@
+CONFIG_SYS_EXTRA_OPTIONS="PPC_T1024,SECURE_BOOT"
+CONFIG_PPC=y
+CONFIG_MPC85xx=y
+CONFIG_TARGET_T102XRDB=y
diff --git a/configs/T1024RDB_SPIFLASH_defconfig b/configs/T1024RDB_SPIFLASH_defconfig
new file mode 100644
index 0000000..c8ea985
--- /dev/null
+++ b/configs/T1024RDB_SPIFLASH_defconfig
@@ -0,0 +1,5 @@
+CONFIG_SPL=y
+CONFIG_SYS_EXTRA_OPTIONS="PPC_T1024,RAMBOOT_PBL,SPL_FSL_PBL,SPIFLASH"
++S:CONFIG_PPC=y
++S:CONFIG_MPC85xx=y
++S:CONFIG_TARGET_T102XRDB=y
diff --git a/configs/T1024RDB_defconfig b/configs/T1024RDB_defconfig
new file mode 100644
index 0000000..e19e404
--- /dev/null
+++ b/configs/T1024RDB_defconfig
@@ -0,0 +1,4 @@
+CONFIG_SYS_EXTRA_OPTIONS="PPC_T1024"
+CONFIG_PPC=y
+CONFIG_MPC85xx=y
+CONFIG_TARGET_T102XRDB=y
diff --git a/doc/README.fsl-dpaa b/doc/README.fsl-dpaa
new file mode 100644
index 0000000..0d8d4f6
--- /dev/null
+++ b/doc/README.fsl-dpaa
@@ -0,0 +1,10 @@
+This file documents Freescale DPAA-specific options.
+
+FMan (Frame Manager)
+ - CONFIG_FSL_FM_10GEC_REGULAR_NOTATION
+ on SoCs earlier(e.g. T4240, T2080), the notation between 10GEC and MAC as below:
+ 10GEC1->MAC9, 10GEC2->MAC10, 10GEC3->MAC1, 10GEC4->MAC2
+ on SoCs later(e.g. T1024, etc), the notation between 10GEC and MAC as below:
+ 10GEC1->MAC1, 10GEC2->MAC2
+ so we introduce CONFIG_FSL_FM_10GEC_REGULAR_NOTATION to identify the new SoCs on
+ which 10GEC enumeration is consistent with MAC enumeration.
diff --git a/drivers/ddr/fsl/ctrl_regs.c b/drivers/ddr/fsl/ctrl_regs.c
index 9e2a4d2..fe8aa98 100644
--- a/drivers/ddr/fsl/ctrl_regs.c
+++ b/drivers/ddr/fsl/ctrl_regs.c
@@ -253,22 +253,30 @@
/* -3E = 667 CL5, -25 = CL6 800, -25E = CL5 800 */
#if !defined(CONFIG_SYS_FSL_DDR1)
+/*
+ * Check DIMM configuration, return 2 if quad-rank or two dual-rank
+ * Return 1 if other two slots configuration. Return 0 if single slot.
+ */
static inline int avoid_odt_overlap(const dimm_params_t *dimm_params)
{
#if CONFIG_DIMM_SLOTS_PER_CTLR == 1
if (dimm_params[0].n_ranks == 4)
- return 1;
+ return 2;
#endif
#if CONFIG_DIMM_SLOTS_PER_CTLR == 2
if ((dimm_params[0].n_ranks == 2) &&
(dimm_params[1].n_ranks == 2))
- return 1;
+ return 2;
#ifdef CONFIG_FSL_DDR_FIRST_SLOT_QUAD_CAPABLE
if (dimm_params[0].n_ranks == 4)
- return 1;
+ return 2;
#endif
+
+ if ((dimm_params[0].n_ranks != 0) &&
+ (dimm_params[2].n_ranks != 0))
+ return 1;
#endif
return 0;
}
@@ -316,6 +324,7 @@
#elif defined(CONFIG_SYS_FSL_DDR3)
unsigned int data_rate = get_ddr_freq(0);
int txp;
+ int odt_overlap;
/*
* (tXARD and tXARDS). Empirical?
* The DDR3 spec has not tXARD,
@@ -331,13 +340,23 @@
/* set the turnaround time */
/*
- * for single quad-rank DIMM and two dual-rank DIMMs
+ * for single quad-rank DIMM and two-slot DIMMs
* to avoid ODT overlap
*/
- if (avoid_odt_overlap(dimm_params)) {
+ odt_overlap = avoid_odt_overlap(dimm_params);
+ switch (odt_overlap) {
+ case 2:
twwt_mclk = 2;
trrt_mclk = 1;
+ break;
+ case 1:
+ twwt_mclk = 1;
+ trrt_mclk = 0;
+ break;
+ default:
+ break;
}
+
/* for faster clock, need more time for data setup */
trwt_mclk = (data_rate/1000000 > 1800) ? 2 : 1;
@@ -383,7 +402,7 @@
);
debug("FSLDDR: timing_cfg_0 = 0x%08x\n", ddr->timing_cfg_0);
}
-#endif /* defined(CONFIG_SYS_FSL_DDR2) */
+#endif /* !defined(CONFIG_SYS_FSL_DDR1) */
/* DDR SDRAM Timing Configuration 3 (TIMING_CFG_3) */
static void set_timing_cfg_3(fsl_ddr_cfg_regs_t *ddr,
diff --git a/drivers/ddr/fsl/ddr4_dimm_params.c b/drivers/ddr/fsl/ddr4_dimm_params.c
index 2418dca..aaddc8f 100644
--- a/drivers/ddr/fsl/ddr4_dimm_params.c
+++ b/drivers/ddr/fsl/ddr4_dimm_params.c
@@ -126,6 +126,12 @@
{
unsigned int retval;
int i;
+ const u8 udimm_rc_e_dq[18] = {
+ 0x0c, 0x2c, 0x15, 0x35, 0x15, 0x35, 0x0b, 0x2c, 0x15,
+ 0x35, 0x0b, 0x35, 0x0b, 0x2c, 0x0b, 0x35, 0x15, 0x36
+ };
+ int spd_error = 0;
+ u8 *ptr;
if (spd->mem_type) {
if (spd->mem_type != SPD_MEMTYPE_DDR4) {
@@ -179,6 +185,22 @@
/* Unbuffered DIMMs */
if (spd->mod_section.unbuffered.addr_mapping & 0x1)
pdimm->mirrored_dimm = 1;
+ if ((spd->mod_section.unbuffered.mod_height & 0xe0) == 0 &&
+ (spd->mod_section.unbuffered.ref_raw_card == 0x04)) {
+ /* Fix SPD error found on DIMMs with raw card E0 */
+ for (i = 0; i < 18; i++) {
+ if (spd->mapping[i] == udimm_rc_e_dq[i])
+ continue;
+ spd_error = 1;
+ debug("SPD byte %d: 0x%x, should be 0x%x\n",
+ 60 + i, spd->mapping[i],
+ udimm_rc_e_dq[i]);
+ ptr = (u8 *)&spd->mapping[i];
+ *ptr = udimm_rc_e_dq[i];
+ }
+ if (spd_error)
+ puts("SPD DQ mapping error fixed\n");
+ }
break;
default:
diff --git a/drivers/net/fm/Makefile b/drivers/net/fm/Makefile
index 5ae3b16..d052fcb 100644
--- a/drivers/net/fm/Makefile
+++ b/drivers/net/fm/Makefile
@@ -28,6 +28,8 @@
obj-$(CONFIG_PPC_T1042) += t1040.o
obj-$(CONFIG_PPC_T1020) += t1040.o
obj-$(CONFIG_PPC_T1022) += t1040.o
+obj-$(CONFIG_PPC_T1023) += t1024.o
+obj-$(CONFIG_PPC_T1024) += t1024.o
obj-$(CONFIG_PPC_T2080) += t2080.o
obj-$(CONFIG_PPC_T2081) += t2080.o
obj-$(CONFIG_PPC_T4240) += t4240.o
diff --git a/drivers/net/fm/b4860.c b/drivers/net/fm/b4860.c
index 373cc4f..eb058c9 100644
--- a/drivers/net/fm/b4860.c
+++ b/drivers/net/fm/b4860.c
@@ -10,6 +10,7 @@
#include <asm/io.h>
#include <asm/immap_85xx.h>
#include <asm/fsl_serdes.h>
+#include <hwconfig.h>
u32 port_to_devdisr[] = {
[FM1_DTSEC1] = FSL_CORENET_DEVDISR2_DTSEC1_1,
@@ -46,15 +47,76 @@
phy_interface_t fman_port_enet_if(enum fm_port port)
{
+#if defined(CONFIG_B4860QDS)
+ u32 serdes2_prtcl;
+ char buffer[HWCONFIG_BUFFER_SIZE];
+ char *buf = NULL;
+ ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
+#endif
+
if (is_device_disabled(port))
return PHY_INTERFACE_MODE_NONE;
/*B4860 has two 10Gig Mac*/
if ((port == FM1_10GEC1 || port == FM1_10GEC2) &&
((is_serdes_configured(XAUI_FM1_MAC9)) ||
- (is_serdes_configured(XAUI_FM1_MAC10))))
+ #if !defined(CONFIG_B4860QDS)
+ (is_serdes_configured(XFI_FM1_MAC9)) ||
+ (is_serdes_configured(XFI_FM1_MAC10)) ||
+ #endif
+ (is_serdes_configured(XAUI_FM1_MAC10))
+ ))
return PHY_INTERFACE_MODE_XGMII;
+#if defined(CONFIG_B4860QDS)
+ serdes2_prtcl = in_be32(&gur->rcwsr[4]) &
+ FSL_CORENET2_RCWSR4_SRDS2_PRTCL;
+
+ if (serdes2_prtcl) {
+ serdes2_prtcl >>= FSL_CORENET2_RCWSR4_SRDS2_PRTCL_SHIFT;
+ switch (serdes2_prtcl) {
+ case 0x80:
+ case 0x81:
+ case 0x82:
+ case 0x83:
+ case 0x84:
+ case 0x85:
+ case 0x86:
+ case 0x87:
+ case 0x88:
+ case 0x89:
+ case 0x8a:
+ case 0x8b:
+ case 0x8c:
+ case 0x8d:
+ case 0x8e:
+ case 0xb1:
+ case 0xb2:
+ /*
+ * Extract hwconfig from environment since environment
+ * is not setup yet
+ */
+ getenv_f("hwconfig", buffer, sizeof(buffer));
+ buf = buffer;
+
+ /* check if XFI interface enable in hwconfig for 10g */
+ if (hwconfig_subarg_cmp_f("fsl_b4860_serdes2",
+ "sfp_amc", "sfp", buf)) {
+ if ((port == FM1_10GEC1 ||
+ port == FM1_10GEC2) &&
+ ((is_serdes_configured(XFI_FM1_MAC9)) ||
+ (is_serdes_configured(XFI_FM1_MAC10))))
+ return PHY_INTERFACE_MODE_XGMII;
+ else if ((port == FM1_DTSEC1) ||
+ (port == FM1_DTSEC2) ||
+ (port == FM1_DTSEC3) ||
+ (port == FM1_DTSEC4))
+ return PHY_INTERFACE_MODE_NONE;
+ }
+ }
+ }
+#endif
+
/* Fix me need to handle RGMII here first */
switch (port) {
diff --git a/drivers/net/fm/eth.c b/drivers/net/fm/eth.c
index 137886c..f1e39b9 100644
--- a/drivers/net/fm/eth.c
+++ b/drivers/net/fm/eth.c
@@ -565,9 +565,11 @@
num = fm_eth->num;
#ifdef CONFIG_SYS_FMAN_V3
+#ifndef CONFIG_FSL_FM_10GEC_REGULAR_NOTATION
if (fm_eth->type == FM_ETH_10G_E) {
- /* 10GEC1/10GEC2 use mEMAC9/mEMAC10
- * 10GEC3/10GEC4 use mEMAC1/mEMAC2
+ /* 10GEC1/10GEC2 use mEMAC9/mEMAC10 on T2080/T4240.
+ * 10GEC3/10GEC4 use mEMAC1/mEMAC2 on T2080.
+ * 10GEC1 uses mEMAC1 on T1024.
* so it needs to change the num.
*/
if (fm_eth->num >= 2)
@@ -575,6 +577,7 @@
else
num += 8;
}
+#endif
base = ®->memac[num].fm_memac;
phyregs = ®->memac[num].fm_memac_mdio;
#else
diff --git a/drivers/net/fm/init.c b/drivers/net/fm/init.c
index 6cf21c6..5d82f29 100644
--- a/drivers/net/fm/init.c
+++ b/drivers/net/fm/init.c
@@ -254,8 +254,10 @@
*/
if (((info->port == FM1_DTSEC9) && (PORT_IS_ENABLED(FM1_10GEC1))) ||
((info->port == FM1_DTSEC10) && (PORT_IS_ENABLED(FM1_10GEC2))) ||
+ ((info->port == FM1_DTSEC1) && (PORT_IS_ENABLED(FM1_10GEC1))) ||
((info->port == FM1_DTSEC1) && (PORT_IS_ENABLED(FM1_10GEC3))) ||
((info->port == FM1_DTSEC2) && (PORT_IS_ENABLED(FM1_10GEC4))) ||
+ ((info->port == FM1_10GEC1) && (PORT_IS_ENABLED(FM1_DTSEC1))) ||
((info->port == FM1_10GEC1) && (PORT_IS_ENABLED(FM1_DTSEC9))) ||
((info->port == FM1_10GEC2) && (PORT_IS_ENABLED(FM1_DTSEC10))) ||
((info->port == FM1_10GEC3) && (PORT_IS_ENABLED(FM1_DTSEC1))) ||
diff --git a/drivers/net/fm/t1024.c b/drivers/net/fm/t1024.c
new file mode 100644
index 0000000..9b31173
--- /dev/null
+++ b/drivers/net/fm/t1024.c
@@ -0,0 +1,88 @@
+/* Copyright 2014 Freescale Semiconductor, Inc.
+ *
+ * Shengzhou Liu <Shengzhou.Liu@freescale.com>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <phy.h>
+#include <fm_eth.h>
+#include <asm/immap_85xx.h>
+#include <asm/fsl_serdes.h>
+
+u32 port_to_devdisr[] = {
+ [FM1_DTSEC1] = FSL_CORENET_DEVDISR2_DTSEC1_1,
+ [FM1_DTSEC2] = FSL_CORENET_DEVDISR2_DTSEC1_2,
+ [FM1_DTSEC3] = FSL_CORENET_DEVDISR2_DTSEC1_3,
+ [FM1_DTSEC4] = FSL_CORENET_DEVDISR2_DTSEC1_4,
+ [FM1_10GEC1] = FSL_CORENET_DEVDISR2_10GEC1_1, /* MAC1 */
+};
+
+static int is_device_disabled(enum fm_port port)
+{
+ ccsr_gur_t *gur = (void __iomem *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
+ u32 devdisr2 = in_be32(&gur->devdisr2);
+
+ return port_to_devdisr[port] & devdisr2;
+}
+
+void fman_disable_port(enum fm_port port)
+{
+ ccsr_gur_t *gur = (void __iomem *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
+
+ setbits_be32(&gur->devdisr2, port_to_devdisr[port]);
+}
+
+phy_interface_t fman_port_enet_if(enum fm_port port)
+{
+ ccsr_gur_t *gur = (void __iomem *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
+ u32 rcwsr13 = in_be32(&gur->rcwsr[13]);
+
+ if (is_device_disabled(port))
+ return PHY_INTERFACE_MODE_NONE;
+
+ if ((port == FM1_10GEC1) && (is_serdes_configured(XFI_FM1_MAC1)))
+ return PHY_INTERFACE_MODE_XGMII;
+
+ if ((port == FM1_DTSEC3) && ((rcwsr13 & FSL_CORENET_RCWSR13_EC2) ==
+ FSL_CORENET_RCWSR13_EC2_RGMII) &&
+ (!is_serdes_configured(QSGMII_FM1_A)))
+ return PHY_INTERFACE_MODE_RGMII;
+
+ if ((port == FM1_DTSEC4) && ((rcwsr13 & FSL_CORENET_RCWSR13_EC1) ==
+ FSL_CORENET_RCWSR13_EC1_RGMII) &&
+ (!is_serdes_configured(QSGMII_FM1_A)))
+ return PHY_INTERFACE_MODE_RGMII;
+
+ /* handle SGMII */
+ switch (port) {
+ case FM1_DTSEC1:
+ case FM1_DTSEC2:
+ case FM1_DTSEC3:
+ if (is_serdes_configured(SGMII_FM1_DTSEC1 + port - FM1_DTSEC1))
+ return PHY_INTERFACE_MODE_SGMII;
+ else if (is_serdes_configured(SGMII_2500_FM1_DTSEC1
+ + port - FM1_DTSEC1))
+ return PHY_INTERFACE_MODE_SGMII_2500;
+ break;
+ default:
+ break;
+ }
+
+ /* handle QSGMII */
+ switch (port) {
+ case FM1_DTSEC1:
+ case FM1_DTSEC2:
+ case FM1_DTSEC3:
+ case FM1_DTSEC4:
+ /* check lane A on SerDes1 */
+ if (is_serdes_configured(QSGMII_FM1_A))
+ return PHY_INTERFACE_MODE_QSGMII;
+ break;
+ default:
+ break;
+ }
+
+ return PHY_INTERFACE_MODE_NONE;
+}
diff --git a/drivers/net/fm/t1040.c b/drivers/net/fm/t1040.c
index 4cce46d..d2a097e 100644
--- a/drivers/net/fm/t1040.c
+++ b/drivers/net/fm/t1040.c
@@ -25,8 +25,6 @@
else if ((rcwsr13 & FSL_CORENET_RCWSR13_EC1) ==
FSL_CORENET_RCWSR13_EC1_FM1_DTSEC4_MII)
return PHY_INTERFACE_MODE_MII;
- else
- return PHY_INTERFACE_MODE_NONE;
}
if ((port == FM1_DTSEC4) &&
@@ -38,8 +36,6 @@
else if ((rcwsr13 & FSL_CORENET_RCWSR13_EC1) ==
FSL_CORENET_RCWSR13_EC1_FM1_DTSEC4_MII)
return PHY_INTERFACE_MODE_MII;
- else
- return PHY_INTERFACE_MODE_NONE;
}
if (port == FM1_DTSEC5) {
diff --git a/drivers/net/phy/Makefile b/drivers/net/phy/Makefile
index 9556536..f46bf00 100644
--- a/drivers/net/phy/Makefile
+++ b/drivers/net/phy/Makefile
@@ -13,6 +13,7 @@
obj-$(CONFIG_PHYLIB_10G) += generic_10g.o
obj-$(CONFIG_PHY_ATHEROS) += atheros.o
obj-$(CONFIG_PHY_BROADCOM) += broadcom.o
+obj-$(CONFIG_PHY_CORTINA) += cortina.o
obj-$(CONFIG_PHY_DAVICOM) += davicom.o
obj-$(CONFIG_PHY_ET1011C) += et1011c.o
obj-$(CONFIG_PHY_LXT) += lxt.o
diff --git a/drivers/net/phy/cortina.c b/drivers/net/phy/cortina.c
new file mode 100644
index 0000000..254f056
--- /dev/null
+++ b/drivers/net/phy/cortina.c
@@ -0,0 +1,333 @@
+/*
+ * Cortina CS4315/CS4340 10G PHY drivers
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ *
+ * Copyright 2014 Freescale Semiconductor, Inc.
+ *
+ */
+
+#include <config.h>
+#include <common.h>
+#include <malloc.h>
+#include <linux/ctype.h>
+#include <linux/string.h>
+#include <linux/err.h>
+#include <phy.h>
+#include <cortina.h>
+#ifdef CONFIG_SYS_CORTINA_FW_IN_NAND
+#include <nand.h>
+#elif defined(CONFIG_SYS_CORTINA_FW_IN_SPIFLASH)
+#include <spi_flash.h>
+#elif defined(CONFIG_SYS_CORTINA_FW_IN_MMC)
+#include <mmc.h>
+#endif
+
+#ifndef CONFIG_PHYLIB_10G
+#error The Cortina PHY needs 10G support
+#endif
+
+struct cortina_reg_config cortina_reg_cfg[] = {
+ /* CS4315_enable_sr_mode */
+ {VILLA_GLOBAL_MSEQCLKCTRL, 0x8004},
+ {VILLA_MSEQ_OPTIONS, 0xf},
+ {VILLA_MSEQ_PC, 0x0},
+ {VILLA_MSEQ_BANKSELECT, 0x4},
+ {VILLA_LINE_SDS_COMMON_SRX0_RX_CPA, 0x55},
+ {VILLA_LINE_SDS_COMMON_SRX0_RX_LOOP_FILTER, 0x30},
+ {VILLA_DSP_SDS_SERDES_SRX_DFE0_SELECT, 0x1},
+ {VILLA_DSP_SDS_DSP_COEF_DFE0_SELECT, 0x2},
+ {VILLA_LINE_SDS_COMMON_SRX0_RX_CPB, 0x2003},
+ {VILLA_DSP_SDS_SERDES_SRX_FFE_DELAY_CTRL, 0xF047},
+ {VILLA_MSEQ_ENABLE_MSB, 0x0000},
+ {VILLA_MSEQ_SPARE21_LSB, 0x6},
+ {VILLA_MSEQ_RESET_COUNT_LSB, 0x0},
+ {VILLA_MSEQ_SPARE12_MSB, 0x0000},
+ /*
+ * to invert the receiver path, uncomment the next line
+ * write (VILLA_MSEQ_SPARE12_MSB, 0x4000)
+ *
+ * SPARE2_LSB is used to configure the device while in sr mode to
+ * enable power savings and to use the optical module LOS signal.
+ * in power savings mode, the internal prbs checker can not be used.
+ * if the optical module LOS signal is used as an input to the micro
+ * code, then the micro code will wait until the optical module
+ * LOS = 0 before turning on the adaptive equalizer.
+ * Setting SPARE2_LSB bit 0 to 1 places the devie in power savings mode
+ * while setting bit 0 to 0 disables power savings mode.
+ * Setting SPARE2_LSB bit 2 to 0 configures the device to use the
+ * optical module LOS signal while setting bit 2 to 1 configures the
+ * device so that it will ignore the optical module LOS SPARE2_LSB = 0
+ */
+
+ /* enable power savings, ignore optical module LOS */
+ {VILLA_MSEQ_SPARE2_LSB, 0x5},
+
+ {VILLA_MSEQ_SPARE7_LSB, 0x1e},
+ {VILLA_MSEQ_BANKSELECT, 0x4},
+ {VILLA_MSEQ_SPARE9_LSB, 0x2},
+ {VILLA_MSEQ_SPARE3_LSB, 0x0F53},
+ {VILLA_MSEQ_SPARE3_MSB, 0x2006},
+ {VILLA_MSEQ_SPARE8_LSB, 0x3FF7},
+ {VILLA_MSEQ_SPARE8_MSB, 0x0A46},
+ {VILLA_MSEQ_COEF8_FFE0_LSB, 0xD500},
+ {VILLA_MSEQ_COEF8_FFE1_LSB, 0x0200},
+ {VILLA_MSEQ_COEF8_FFE2_LSB, 0xBA00},
+ {VILLA_MSEQ_COEF8_FFE3_LSB, 0x0100},
+ {VILLA_MSEQ_COEF8_FFE4_LSB, 0x0300},
+ {VILLA_MSEQ_COEF8_FFE5_LSB, 0x0300},
+ {VILLA_MSEQ_COEF8_DFE0_LSB, 0x0700},
+ {VILLA_MSEQ_COEF8_DFE0N_LSB, 0x0E00},
+ {VILLA_MSEQ_COEF8_DFE1_LSB, 0x0B00},
+ {VILLA_DSP_SDS_DSP_COEF_LARGE_LEAK, 0x2},
+ {VILLA_DSP_SDS_SERDES_SRX_DAC_ENABLEB_LSB, 0xD000},
+ {VILLA_MSEQ_POWER_DOWN_LSB, 0xFFFF},
+ {VILLA_MSEQ_POWER_DOWN_MSB, 0x0},
+ {VILLA_MSEQ_CAL_RX_SLICER, 0x80},
+ {VILLA_DSP_SDS_SERDES_SRX_DAC_BIAS_SELECT1_MSB, 0x3f},
+ {VILLA_GLOBAL_MSEQCLKCTRL, 0x4},
+ {VILLA_MSEQ_OPTIONS, 0x7},
+
+ /* set up min value for ffe1 */
+ {VILLA_MSEQ_COEF_INIT_SEL, 0x2},
+ {VILLA_DSP_SDS_DSP_PRECODEDINITFFE21, 0x41},
+
+ /* CS4315_sr_rx_pre_eq_set_4in */
+ {VILLA_GLOBAL_MSEQCLKCTRL, 0x8004},
+ {VILLA_MSEQ_OPTIONS, 0xf},
+ {VILLA_MSEQ_BANKSELECT, 0x4},
+ {VILLA_MSEQ_PC, 0x0},
+
+ /* for lengths from 3.5 to 4.5inches */
+ {VILLA_MSEQ_SERDES_PARAM_LSB, 0x0306},
+ {VILLA_MSEQ_SPARE25_LSB, 0x0306},
+ {VILLA_MSEQ_SPARE21_LSB, 0x2},
+ {VILLA_MSEQ_SPARE23_LSB, 0x2},
+ {VILLA_MSEQ_CAL_RX_DFE_EQ, 0x0},
+
+ {VILLA_GLOBAL_MSEQCLKCTRL, 0x4},
+ {VILLA_MSEQ_OPTIONS, 0x7},
+
+ /* CS4315_rx_drive_4inch */
+ /* for length 4inches */
+ {VILLA_GLOBAL_VILLA2_COMPATIBLE, 0x0000},
+ {VILLA_HOST_SDS_COMMON_STX0_TX_OUTPUT_CTRLA, 0x3023},
+ {VILLA_LINE_SDS_COMMON_STX0_TX_OUTPUT_CTRLB, 0xc01E},
+
+ /* CS4315_tx_drive_4inch */
+ /* for length 4inches */
+ {VILLA_GLOBAL_VILLA2_COMPATIBLE, 0x0000},
+ {VILLA_LINE_SDS_COMMON_STX0_TX_OUTPUT_CTRLA, 0x3023},
+ {VILLA_LINE_SDS_COMMON_STX0_TX_OUTPUT_CTRLB, 0xc01E},
+};
+
+void cs4340_upload_firmware(struct phy_device *phydev)
+{
+ char line_temp[0x50] = {0};
+ char reg_addr[0x50] = {0};
+ char reg_data[0x50] = {0};
+ int i, line_cnt = 0, column_cnt = 0;
+ struct cortina_reg_config fw_temp;
+ char *addr = NULL;
+
+#if defined(CONFIG_SYS_CORTINA_FW_IN_NOR) || \
+ defined(CONFIG_SYS_CORTINA_FW_IN_REMOTE)
+
+ addr = (char *)CONFIG_CORTINA_FW_ADDR;
+#elif defined(CONFIG_SYS_CORTINA_FW_IN_NAND)
+ int ret;
+ size_t fw_length = CONFIG_CORTINA_FW_LENGTH;
+
+ addr = malloc(CONFIG_CORTINA_FW_LENGTH);
+ ret = nand_read(&nand_info[0], (loff_t)CONFIG_CORTINA_FW_ADDR,
+ &fw_length, (u_char *)addr);
+ if (ret == -EUCLEAN) {
+ printf("NAND read of Cortina firmware at 0x%x failed %d\n",
+ CONFIG_CORTINA_FW_ADDR, ret);
+ }
+#elif defined(CONFIG_SYS_CORTINA_FW_IN_SPIFLASH)
+ int ret;
+ struct spi_flash *ucode_flash;
+
+ addr = malloc(CONFIG_CORTINA_FW_LENGTH);
+ ucode_flash = spi_flash_probe(CONFIG_ENV_SPI_BUS, CONFIG_ENV_SPI_CS,
+ CONFIG_ENV_SPI_MAX_HZ, CONFIG_ENV_SPI_MODE);
+ if (!ucode_flash) {
+ puts("SF: probe for Cortina ucode failed\n");
+ } else {
+ ret = spi_flash_read(ucode_flash, CONFIG_CORTINA_FW_ADDR,
+ CONFIG_CORTINA_FW_LENGTH, addr);
+ if (ret)
+ puts("SF: read for Cortina ucode failed\n");
+ spi_flash_free(ucode_flash);
+ }
+#elif defined(CONFIG_SYS_CORTINA_FW_IN_MMC)
+ int dev = CONFIG_SYS_MMC_ENV_DEV;
+ u32 cnt = CONFIG_CORTINA_FW_LENGTH / 512;
+ u32 blk = CONFIG_CORTINA_FW_ADDR / 512;
+ struct mmc *mmc = find_mmc_device(CONFIG_SYS_MMC_ENV_DEV);
+
+ if (!mmc) {
+ puts("Failed to find MMC device for Cortina ucode\n");
+ } else {
+ addr = malloc(CONFIG_CORTINA_FW_LENGTH);
+ printf("MMC read: dev # %u, block # %u, count %u ...\n",
+ dev, blk, cnt);
+ mmc_init(mmc);
+ (void)mmc->block_dev.block_read(dev, blk, cnt, addr);
+ /* flush cache after read */
+ flush_cache((ulong)addr, cnt * 512);
+ }
+#endif
+
+ while (*addr != 'Q') {
+ i = 0;
+
+ while (*addr != 0x0a) {
+ line_temp[i++] = *addr++;
+ if (0x50 < i) {
+ printf("Not found Cortina PHY ucode at 0x%x\n",
+ CONFIG_CORTINA_FW_ADDR);
+ return;
+ }
+ }
+
+ addr++; /* skip '\n' */
+ line_cnt++;
+ column_cnt = i;
+ line_temp[column_cnt] = '\0';
+
+ if (CONFIG_CORTINA_FW_LENGTH < line_cnt)
+ return;
+
+ for (i = 0; i < column_cnt; i++) {
+ if (isspace(line_temp[i++]))
+ break;
+ }
+
+ memcpy(reg_addr, line_temp, i);
+ memcpy(reg_data, &line_temp[i], column_cnt - i);
+ strim(reg_addr);
+ strim(reg_data);
+ fw_temp.reg_addr = (simple_strtoul(reg_addr, NULL, 0)) & 0xffff;
+ fw_temp.reg_value = (simple_strtoul(reg_data, NULL, 0)) &
+ 0xffff;
+ phy_write(phydev, 0x00, fw_temp.reg_addr, fw_temp.reg_value);
+ }
+}
+
+int cs4340_phy_init(struct phy_device *phydev)
+{
+ int timeout = 100; /* 100ms */
+ int reg_value;
+
+ /* step1: BIST test */
+ phy_write(phydev, 0x00, VILLA_GLOBAL_MSEQCLKCTRL, 0x0004);
+ phy_write(phydev, 0x00, VILLA_GLOBAL_LINE_SOFT_RESET, 0x0000);
+ phy_write(phydev, 0x00, VILLA_GLOBAL_BIST_CONTROL, 0x0001);
+ while (--timeout) {
+ reg_value = phy_read(phydev, 0x00, VILLA_GLOBAL_BIST_STATUS);
+ if (reg_value & mseq_edc_bist_done) {
+ if (0 == (reg_value & mseq_edc_bist_fail))
+ break;
+ }
+ udelay(1000);
+ }
+
+ if (!timeout) {
+ printf("%s BIST mseq_edc_bist_done timeout!\n", __func__);
+ return -1;
+ }
+
+ /* setp2: upload ucode */
+ cs4340_upload_firmware(phydev);
+ reg_value = phy_read(phydev, 0x00, VILLA_GLOBAL_DWNLD_CHECKSUM_STATUS);
+ if (reg_value) {
+ debug("%s checksum status failed.\n", __func__);
+ return -1;
+ }
+
+ return 0;
+}
+
+int cs4340_config(struct phy_device *phydev)
+{
+ cs4340_phy_init(phydev);
+ return 0;
+}
+
+int cs4340_startup(struct phy_device *phydev)
+{
+ phydev->link = 1;
+
+ /* For now just lie and say it's 10G all the time */
+ phydev->speed = SPEED_10000;
+ phydev->duplex = DUPLEX_FULL;
+ return 0;
+}
+
+struct phy_driver cs4340_driver = {
+ .name = "Cortina CS4315/CS4340",
+ .uid = PHY_UID_CS4340,
+ .mask = 0xfffffff0,
+ .features = PHY_10G_FEATURES,
+ .mmds = (MDIO_DEVS_PMAPMD | MDIO_DEVS_PCS |
+ MDIO_DEVS_PHYXS | MDIO_DEVS_AN |
+ MDIO_DEVS_VEND1 | MDIO_DEVS_VEND2),
+ .config = &cs4340_config,
+ .startup = &cs4340_startup,
+ .shutdown = &gen10g_shutdown,
+};
+
+int phy_cortina_init(void)
+{
+ phy_register(&cs4340_driver);
+ return 0;
+}
+
+int get_phy_id(struct mii_dev *bus, int addr, int devad, u32 *phy_id)
+{
+ int phy_reg;
+ bool is_cortina_phy = false;
+
+ switch (addr) {
+#ifdef CORTINA_PHY_ADDR1
+ case CORTINA_PHY_ADDR1:
+#endif
+#ifdef CORTINA_PHY_ADDR2
+ case CORTINA_PHY_ADDR2:
+#endif
+#ifdef CORTINA_PHY_ADDR3
+ case CORTINA_PHY_ADDR3:
+#endif
+#ifdef CORTINA_PHY_ADDR4
+ case CORTINA_PHY_ADDR4:
+#endif
+ is_cortina_phy = true;
+ break;
+ default:
+ break;
+ }
+
+ /* Cortina PHY has non-standard offset of PHY ID registers */
+ if (is_cortina_phy)
+ phy_reg = bus->read(bus, addr, 0, VILLA_GLOBAL_CHIP_ID_LSB);
+ else
+ phy_reg = bus->read(bus, addr, devad, MII_PHYSID1);
+
+ if (phy_reg < 0)
+ return -EIO;
+
+ *phy_id = (phy_reg & 0xffff) << 16;
+ if (is_cortina_phy)
+ phy_reg = bus->read(bus, addr, 0, VILLA_GLOBAL_CHIP_ID_MSB);
+ else
+ phy_reg = bus->read(bus, addr, devad, MII_PHYSID2);
+
+ if (phy_reg < 0)
+ return -EIO;
+
+ *phy_id |= (phy_reg & 0xffff);
+
+ return 0;
+}
diff --git a/drivers/net/phy/phy.c b/drivers/net/phy/phy.c
index 467c972..5b04c85 100644
--- a/drivers/net/phy/phy.c
+++ b/drivers/net/phy/phy.c
@@ -448,6 +448,9 @@
#ifdef CONFIG_PHY_BROADCOM
phy_broadcom_init();
#endif
+#ifdef CONFIG_PHY_CORTINA
+ phy_cortina_init();
+#endif
#ifdef CONFIG_PHY_DAVICOM
phy_davicom_init();
#endif
diff --git a/drivers/net/phy/vitesse.c b/drivers/net/phy/vitesse.c
index 2b29cd8..20a6746 100644
--- a/drivers/net/phy/vitesse.c
+++ b/drivers/net/phy/vitesse.c
@@ -1,8 +1,8 @@
/*
* Vitesse PHY drivers
*
- * Copyright 2010-2012 Freescale Semiconductor, Inc.
- * Author: Andy Fleming
+ * Copyright 2010-2014 Freescale Semiconductor, Inc.
+ * Original Author: Andy Fleming
* Add vsc8662 phy support - Priyanka Jain
* SPDX-License-Identifier: GPL-2.0+
*/
@@ -50,6 +50,7 @@
#define MIIM_VSC8574_18G_CMDSTAT 0x8000
/* Vitesse VSC8514 control register */
+#define MIIM_VSC8514_MAC_SERDES_CON 0x10
#define MIIM_VSC8514_GENERAL18 0x12
#define MIIM_VSC8514_GENERAL19 0x13
#define MIIM_VSC8514_GENERAL23 0x17
@@ -246,6 +247,14 @@
val = (val & 0xf8ff);
phy_write(phydev, MDIO_DEVAD_NONE, MIIM_VSC8514_GENERAL23, val);
+ /* Enable Serdes Auto-negotiation */
+ phy_write(phydev, MDIO_DEVAD_NONE, PHY_EXT_PAGE_ACCESS,
+ PHY_EXT_PAGE_ACCESS_EXTENDED3);
+ val = phy_read(phydev, MDIO_DEVAD_NONE, MIIM_VSC8514_MAC_SERDES_CON);
+ val = val | MIIM_VSC8574_MAC_SERDES_ANEG;
+ phy_write(phydev, MDIO_DEVAD_NONE, MIIM_VSC8514_MAC_SERDES_CON, val);
+ phy_write(phydev, MDIO_DEVAD_NONE, PHY_EXT_PAGE_ACCESS, 0);
+
genphy_config_aneg(phydev);
return 0;
diff --git a/include/configs/B4860QDS.h b/include/configs/B4860QDS.h
index dc1a9bc..9e8e319 100644
--- a/include/configs/B4860QDS.h
+++ b/include/configs/B4860QDS.h
@@ -713,8 +713,8 @@
#endif /* CONFIG_PCI */
#ifdef CONFIG_FMAN_ENET
-#define CONFIG_SYS_FM1_DTSEC5_PHY_ADDR 0x10
-#define CONFIG_SYS_FM1_DTSEC6_PHY_ADDR 0x11
+#define CONFIG_SYS_FM1_ONBOARD_PHY1_ADDR 0x10
+#define CONFIG_SYS_FM1_ONBOARD_PHY2_ADDR 0x11
/*B4860 QDS AMC2PEX-2S default PHY_ADDR */
#define CONFIG_SYS_FM1_10GEC1_PHY_ADDR 0x7 /*SLOT 1*/
@@ -731,6 +731,8 @@
#define CONFIG_PHY_GIGE /* Include GbE speed/duplex detection */
#endif
+#define CONFIG_SYS_FSL_B4860QDS_XFI_ERR
+
/*
* Environment
*/
diff --git a/include/configs/C29XPCIE.h b/include/configs/C29XPCIE.h
index 5d11278..ecb3d7b 100644
--- a/include/configs/C29XPCIE.h
+++ b/include/configs/C29XPCIE.h
@@ -12,6 +12,8 @@
#define __CONFIG_H
#define CONFIG_PHYS_64BIT
+#define CONFIG_SYS_GENERIC_BOARD
+#define CONFIG_DISPLAY_BOARDINFO
#ifdef CONFIG_C29XPCIE
#define CONFIG_PPC_C29X
diff --git a/include/configs/P1010RDB.h b/include/configs/P1010RDB.h
index d378dbd..cd6a39c 100644
--- a/include/configs/P1010RDB.h
+++ b/include/configs/P1010RDB.h
@@ -14,6 +14,8 @@
#ifdef CONFIG_36BIT
#define CONFIG_PHYS_64BIT
#endif
+#define CONFIG_SYS_GENERIC_BOARD
+#define CONFIG_DISPLAY_BOARDINFO
#define CONFIG_P1010
#define CONFIG_E500 /* BOOKE e500 family */
diff --git a/include/configs/P1022DS.h b/include/configs/P1022DS.h
index bd08090..4371110 100644
--- a/include/configs/P1022DS.h
+++ b/include/configs/P1022DS.h
@@ -11,6 +11,9 @@
#include "../board/freescale/common/ics307_clk.h"
+#define CONFIG_SYS_GENERIC_BOARD
+#define CONFIG_DISPLAY_BOARDINFO
+
#ifdef CONFIG_36BIT
#define CONFIG_PHYS_64BIT
#endif
diff --git a/include/configs/P1023RDB.h b/include/configs/P1023RDB.h
index 6b29add..2ce186e 100644
--- a/include/configs/P1023RDB.h
+++ b/include/configs/P1023RDB.h
@@ -10,6 +10,9 @@
#ifndef __CONFIG_H
#define __CONFIG_H
+#define CONFIG_SYS_GENERIC_BOARD
+#define CONFIG_DISPLAY_BOARDINFO
+
#ifndef CONFIG_SYS_TEXT_BASE
#define CONFIG_SYS_TEXT_BASE 0xeff40000
#endif
diff --git a/include/configs/P5040DS.h b/include/configs/P5040DS.h
index 371485f..e4a031a 100644
--- a/include/configs/P5040DS.h
+++ b/include/configs/P5040DS.h
@@ -17,6 +17,7 @@
#define CONFIG_MMC
#define CONFIG_NAND_FSL_ELBC
#define CONFIG_PCIE3
+#define CONFIG_FSL_SATA_V2
#define CONFIG_SYS_FSL_RAID_ENGINE
#define CONFIG_ICS307_REFCLK_HZ 25000000 /* ICS307 ref clk freq */
diff --git a/include/configs/T102xQDS.h b/include/configs/T102xQDS.h
new file mode 100644
index 0000000..78ed243
--- /dev/null
+++ b/include/configs/T102xQDS.h
@@ -0,0 +1,939 @@
+/*
+ * Copyright 2014 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+/*
+ * T1024/T1023 QDS board configuration file
+ */
+
+#ifndef __T1024QDS_H
+#define __T1024QDS_H
+
+/* High Level Configuration Options */
+#define CONFIG_SYS_GENERIC_BOARD
+#define CONFIG_DISPLAY_BOARDINFO
+#define CONFIG_BOOKE
+#define CONFIG_E500 /* BOOKE e500 family */
+#define CONFIG_E500MC /* BOOKE e500mc family */
+#define CONFIG_SYS_BOOK3E_HV /* Category E.HV supported */
+#define CONFIG_MP /* support multiple processors */
+#define CONFIG_PHYS_64BIT
+#define CONFIG_ENABLE_36BIT_PHYS
+
+#ifdef CONFIG_PHYS_64BIT
+#define CONFIG_ADDR_MAP 1
+#define CONFIG_SYS_NUM_ADDR_MAP 64 /* number of TLB1 entries */
+#endif
+
+#define CONFIG_SYS_FSL_CPC /* Corenet Platform Cache */
+#define CONFIG_SYS_NUM_CPC CONFIG_NUM_DDR_CONTROLLERS
+#define CONFIG_FSL_IFC /* Enable IFC Support */
+
+#define CONFIG_FSL_LAW /* Use common FSL init code */
+#define CONFIG_ENV_OVERWRITE
+
+#define CONFIG_DEEP_SLEEP
+#define CONFIG_SILENT_CONSOLE
+
+#ifdef CONFIG_RAMBOOT_PBL
+#define CONFIG_SYS_FSL_PBL_PBI board/freescale/t102xqds/t1024_pbi.cfg
+#define CONFIG_SYS_FSL_PBL_RCW board/freescale/t102xqds/t1024_rcw.cfg
+#define CONFIG_SPL_MPC8XXX_INIT_DDR_SUPPORT
+#define CONFIG_SPL_ENV_SUPPORT
+#define CONFIG_SPL_SERIAL_SUPPORT
+#define CONFIG_SPL_FLUSH_IMAGE
+#define CONFIG_SPL_TARGET "u-boot-with-spl.bin"
+#define CONFIG_SPL_LIBGENERIC_SUPPORT
+#define CONFIG_SPL_LIBCOMMON_SUPPORT
+#define CONFIG_SPL_I2C_SUPPORT
+#define CONFIG_SPL_DRIVERS_MISC_SUPPORT
+#define CONFIG_FSL_LAW /* Use common FSL init code */
+#define CONFIG_SYS_TEXT_BASE 0x00201000
+#define CONFIG_SPL_TEXT_BASE 0xFFFD8000
+#define CONFIG_SPL_PAD_TO 0x40000
+#define CONFIG_SPL_MAX_SIZE 0x28000
+#define RESET_VECTOR_OFFSET 0x27FFC
+#define BOOT_PAGE_OFFSET 0x27000
+#ifdef CONFIG_SPL_BUILD
+#define CONFIG_SPL_SKIP_RELOCATE
+#define CONFIG_SPL_COMMON_INIT_DDR
+#define CONFIG_SYS_CCSR_DO_NOT_RELOCATE
+#define CONFIG_SYS_NO_FLASH
+#endif
+
+#ifdef CONFIG_NAND
+#define CONFIG_SPL_NAND_SUPPORT
+#define CONFIG_SYS_NAND_U_BOOT_SIZE (768 << 10)
+#define CONFIG_SYS_NAND_U_BOOT_DST 0x00200000
+#define CONFIG_SYS_NAND_U_BOOT_START 0x00200000
+#define CONFIG_SYS_NAND_U_BOOT_OFFS (256 << 10)
+#define CONFIG_SYS_LDSCRIPT "arch/powerpc/cpu/mpc85xx/u-boot-nand.lds"
+#define CONFIG_SPL_NAND_BOOT
+#endif
+
+#ifdef CONFIG_SPIFLASH
+#define CONFIG_RESET_VECTOR_ADDRESS 0x200FFC
+#define CONFIG_SPL_SPI_SUPPORT
+#define CONFIG_SPL_SPI_FLASH_SUPPORT
+#define CONFIG_SPL_SPI_FLASH_MINIMAL
+#define CONFIG_SYS_SPI_FLASH_U_BOOT_SIZE (768 << 10)
+#define CONFIG_SYS_SPI_FLASH_U_BOOT_DST (0x00200000)
+#define CONFIG_SYS_SPI_FLASH_U_BOOT_START (0x00200000)
+#define CONFIG_SYS_SPI_FLASH_U_BOOT_OFFS (256 << 10)
+#define CONFIG_SYS_LDSCRIPT "arch/powerpc/cpu/mpc85xx/u-boot.lds"
+#ifndef CONFIG_SPL_BUILD
+#define CONFIG_SYS_MPC85XX_NO_RESETVEC
+#endif
+#define CONFIG_SPL_SPI_BOOT
+#endif
+
+#ifdef CONFIG_SDCARD
+#define CONFIG_RESET_VECTOR_ADDRESS 0x200FFC
+#define CONFIG_SPL_MMC_SUPPORT
+#define CONFIG_SPL_MMC_MINIMAL
+#define CONFIG_SYS_MMC_U_BOOT_SIZE (768 << 10)
+#define CONFIG_SYS_MMC_U_BOOT_DST (0x00200000)
+#define CONFIG_SYS_MMC_U_BOOT_START (0x00200000)
+#define CONFIG_SYS_MMC_U_BOOT_OFFS (260 << 10)
+#define CONFIG_SYS_LDSCRIPT "arch/powerpc/cpu/mpc85xx/u-boot.lds"
+#ifndef CONFIG_SPL_BUILD
+#define CONFIG_SYS_MPC85XX_NO_RESETVEC
+#endif
+#define CONFIG_SPL_MMC_BOOT
+#endif
+
+#endif /* CONFIG_RAMBOOT_PBL */
+
+#ifndef CONFIG_SYS_TEXT_BASE
+#define CONFIG_SYS_TEXT_BASE 0xeff40000
+#endif
+
+#ifndef CONFIG_RESET_VECTOR_ADDRESS
+#define CONFIG_RESET_VECTOR_ADDRESS 0xeffffffc
+#endif
+
+#ifndef CONFIG_SYS_NO_FLASH
+#define CONFIG_FLASH_CFI_DRIVER
+#define CONFIG_SYS_FLASH_CFI
+#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
+#endif
+
+/* PCIe Boot - Master */
+#define CONFIG_SRIO_PCIE_BOOT_MASTER
+/*
+ * for slave u-boot IMAGE instored in master memory space,
+ * PHYS must be aligned based on the SIZE
+ */
+#define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS1 0xfff00000ull
+#define CONFIG_SRIO_PCIE_BOOT_IMAGE_SIZE 0x100000 /* 1M */
+#ifdef CONFIG_PHYS_64BIT
+#define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_PHYS 0xfef200000ull
+#define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS2 0x3fff00000ull
+#else
+#define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_PHYS 0xef200000
+#define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS2 0xfff00000
+#endif
+/*
+ * for slave UCODE and ENV instored in master memory space,
+ * PHYS must be aligned based on the SIZE
+ */
+#ifdef CONFIG_PHYS_64BIT
+#define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_PHYS 0xfef100000ull
+#define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_BUS 0x3ffe00000ull
+#else
+#define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_PHYS 0xef100000
+#define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_BUS 0xffe00000
+#endif
+#define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_SIZE 0x40000 /* 256K */
+/* slave core release by master*/
+#define CONFIG_SRIO_PCIE_BOOT_BRR_OFFSET 0xe00e4
+#define CONFIG_SRIO_PCIE_BOOT_RELEASE_MASK 0x00000001 /* release core 0 */
+
+/* PCIe Boot - Slave */
+#ifdef CONFIG_SRIO_PCIE_BOOT_SLAVE
+#define CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR 0xFFE00000
+#define CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR_PHYS \
+ (0x300000000ull | CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR)
+/* Set 1M boot space for PCIe boot */
+#define CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR (CONFIG_SYS_TEXT_BASE & 0xfff00000)
+#define CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR_PHYS \
+ (0x300000000ull | CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR)
+#define CONFIG_RESET_VECTOR_ADDRESS 0xfffffffc
+#define CONFIG_SYS_NO_FLASH
+#endif
+
+#if defined(CONFIG_SPIFLASH)
+#define CONFIG_SYS_EXTRA_ENV_RELOC
+#define CONFIG_ENV_IS_IN_SPI_FLASH
+#define CONFIG_ENV_SPI_BUS 0
+#define CONFIG_ENV_SPI_CS 0
+#define CONFIG_ENV_SPI_MAX_HZ 10000000
+#define CONFIG_ENV_SPI_MODE 0
+#define CONFIG_ENV_SIZE 0x2000 /* 8KB */
+#define CONFIG_ENV_OFFSET 0x100000 /* 1MB */
+#define CONFIG_ENV_SECT_SIZE 0x10000
+#elif defined(CONFIG_SDCARD)
+#define CONFIG_SYS_EXTRA_ENV_RELOC
+#define CONFIG_ENV_IS_IN_MMC
+#define CONFIG_SYS_MMC_ENV_DEV 0
+#define CONFIG_ENV_SIZE 0x2000
+#define CONFIG_ENV_OFFSET (512 * 0x800)
+#elif defined(CONFIG_NAND)
+#define CONFIG_SYS_EXTRA_ENV_RELOC
+#define CONFIG_ENV_IS_IN_NAND
+#define CONFIG_ENV_SIZE 0x2000
+#define CONFIG_ENV_OFFSET (10 * CONFIG_SYS_NAND_BLOCK_SIZE)
+#elif defined(CONFIG_SRIO_PCIE_BOOT_SLAVE)
+#define CONFIG_ENV_IS_IN_REMOTE
+#define CONFIG_ENV_ADDR 0xffe20000
+#define CONFIG_ENV_SIZE 0x2000
+#elif defined(CONFIG_ENV_IS_NOWHERE)
+#define CONFIG_ENV_SIZE 0x2000
+#else
+#define CONFIG_ENV_IS_IN_FLASH
+#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SECT_SIZE)
+#define CONFIG_ENV_SIZE 0x2000
+#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K (one sector) */
+#endif
+
+
+#ifndef __ASSEMBLY__
+unsigned long get_board_sys_clk(void);
+unsigned long get_board_ddr_clk(void);
+#endif
+
+#define CONFIG_SYS_CLK_FREQ get_board_sys_clk()
+#define CONFIG_DDR_CLK_FREQ get_board_ddr_clk()
+
+/*
+ * These can be toggled for performance analysis, otherwise use default.
+ */
+#define CONFIG_SYS_CACHE_STASHING
+#define CONFIG_BACKSIDE_L2_CACHE
+#define CONFIG_SYS_INIT_L2CSR0 L2CSR0_L2E
+#define CONFIG_BTB /* toggle branch predition */
+#define CONFIG_DDR_ECC
+#ifdef CONFIG_DDR_ECC
+#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER
+#define CONFIG_MEM_INIT_VALUE 0xdeadbeef
+#endif
+
+#define CONFIG_SYS_MEMTEST_START 0x00200000 /* memtest works on */
+#define CONFIG_SYS_MEMTEST_END 0x00400000
+#define CONFIG_SYS_ALT_MEMTEST
+#define CONFIG_PANIC_HANG /* do not reset board on panic */
+
+/*
+ * Config the L3 Cache as L3 SRAM
+ */
+#define CONFIG_SYS_INIT_L3_ADDR 0xFFFC0000
+#define CONFIG_SYS_L3_SIZE (256 << 10)
+#define CONFIG_SPL_GD_ADDR (CONFIG_SYS_INIT_L3_ADDR + 32 * 1024)
+#ifdef CONFIG_RAMBOOT_PBL
+#define CONFIG_ENV_ADDR (CONFIG_SPL_GD_ADDR + 4 * 1024)
+#endif
+#define CONFIG_SPL_RELOC_MALLOC_ADDR (CONFIG_SPL_GD_ADDR + 12 * 1024)
+#define CONFIG_SPL_RELOC_MALLOC_SIZE (30 << 10)
+#define CONFIG_SPL_RELOC_STACK (CONFIG_SPL_GD_ADDR + 64 * 1024)
+#define CONFIG_SPL_RELOC_STACK_SIZE (22 << 10)
+
+#ifdef CONFIG_PHYS_64BIT
+#define CONFIG_SYS_DCSRBAR 0xf0000000
+#define CONFIG_SYS_DCSRBAR_PHYS 0xf00000000ull
+#endif
+
+/* EEPROM */
+#define CONFIG_ID_EEPROM
+#define CONFIG_SYS_I2C_EEPROM_NXID
+#define CONFIG_SYS_EEPROM_BUS_NUM 0
+#define CONFIG_SYS_I2C_EEPROM_ADDR 0x57
+#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 5
+
+/*
+ * DDR Setup
+ */
+#define CONFIG_VERY_BIG_RAM
+#define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000
+#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE
+#define CONFIG_DIMM_SLOTS_PER_CTLR 1
+#define CONFIG_CHIP_SELECTS_PER_CTRL (4 * CONFIG_DIMM_SLOTS_PER_CTLR)
+#define CONFIG_DDR_SPD
+#ifndef CONFIG_SYS_FSL_DDR4
+#define CONFIG_SYS_FSL_DDR3
+#endif
+
+#define CONFIG_SYS_SPD_BUS_NUM 0
+#define SPD_EEPROM_ADDRESS 0x51
+
+#define CONFIG_SYS_SDRAM_SIZE 4096 /* for fixed parameter use */
+
+/*
+ * IFC Definitions
+ */
+#define CONFIG_SYS_FLASH_BASE 0xe0000000
+#ifdef CONFIG_PHYS_64BIT
+#define CONFIG_SYS_FLASH_BASE_PHYS (0xf00000000ull | CONFIG_SYS_FLASH_BASE)
+#else
+#define CONFIG_SYS_FLASH_BASE_PHYS CONFIG_SYS_FLASH_BASE
+#endif
+
+#define CONFIG_SYS_NOR0_CSPR_EXT (0xf)
+#define CONFIG_SYS_NOR0_CSPR (CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS \
+ + 0x8000000) | \
+ CSPR_PORT_SIZE_16 | \
+ CSPR_MSEL_NOR | \
+ CSPR_V)
+#define CONFIG_SYS_NOR1_CSPR_EXT (0xf)
+#define CONFIG_SYS_NOR1_CSPR (CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) | \
+ CSPR_PORT_SIZE_16 | \
+ CSPR_MSEL_NOR | \
+ CSPR_V)
+#define CONFIG_SYS_NOR_AMASK IFC_AMASK(128*1024*1024)
+/* NOR Flash Timing Params */
+#define CONFIG_SYS_NOR_CSOR CSOR_NAND_TRHZ_80
+#define CONFIG_SYS_NOR_FTIM0 (FTIM0_NOR_TACSE(0x4) | \
+ FTIM0_NOR_TEADC(0x5) | \
+ FTIM0_NOR_TEAHC(0x5))
+#define CONFIG_SYS_NOR_FTIM1 (FTIM1_NOR_TACO(0x35) | \
+ FTIM1_NOR_TRAD_NOR(0x1A) |\
+ FTIM1_NOR_TSEQRAD_NOR(0x13))
+#define CONFIG_SYS_NOR_FTIM2 (FTIM2_NOR_TCS(0x4) | \
+ FTIM2_NOR_TCH(0x4) | \
+ FTIM2_NOR_TWPH(0x0E) | \
+ FTIM2_NOR_TWP(0x1c))
+#define CONFIG_SYS_NOR_FTIM3 0x0
+
+#define CONFIG_SYS_FLASH_QUIET_TEST
+#define CONFIG_FLASH_SHOW_PROGRESS 45 /* count down from 45/5: 9..1 */
+
+#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* number of banks */
+#define CONFIG_SYS_MAX_FLASH_SECT 1024 /* sectors per device */
+#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */
+#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */
+
+#define CONFIG_SYS_FLASH_EMPTY_INFO
+#define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE_PHYS \
+ + 0x8000000, CONFIG_SYS_FLASH_BASE_PHYS}
+#define CONFIG_FSL_QIXIS /* use common QIXIS code */
+#define QIXIS_BASE 0xffdf0000
+#ifdef CONFIG_PHYS_64BIT
+#define QIXIS_BASE_PHYS (0xf00000000ull | QIXIS_BASE)
+#else
+#define QIXIS_BASE_PHYS QIXIS_BASE
+#endif
+#define QIXIS_LBMAP_SWITCH 0x06
+#define QIXIS_LBMAP_MASK 0x0f
+#define QIXIS_LBMAP_SHIFT 0
+#define QIXIS_LBMAP_DFLTBANK 0x00
+#define QIXIS_LBMAP_ALTBANK 0x04
+#define QIXIS_RST_CTL_RESET 0x31
+#define QIXIS_RCFG_CTL_RECONFIG_IDLE 0x20
+#define QIXIS_RCFG_CTL_RECONFIG_START 0x21
+#define QIXIS_RCFG_CTL_WATCHDOG_ENBLE 0x08
+#define QIXIS_RST_FORCE_MEM 0x01
+
+#define CONFIG_SYS_CSPR3_EXT (0xf)
+#define CONFIG_SYS_CSPR3 (CSPR_PHYS_ADDR(QIXIS_BASE_PHYS) \
+ | CSPR_PORT_SIZE_8 \
+ | CSPR_MSEL_GPCM \
+ | CSPR_V)
+#define CONFIG_SYS_AMASK3 IFC_AMASK(4*1024)
+#define CONFIG_SYS_CSOR3 0x0
+/* QIXIS Timing parameters for IFC CS3 */
+#define CONFIG_SYS_CS3_FTIM0 (FTIM0_GPCM_TACSE(0x0e) | \
+ FTIM0_GPCM_TEADC(0x0e) | \
+ FTIM0_GPCM_TEAHC(0x0e))
+#define CONFIG_SYS_CS3_FTIM1 (FTIM1_GPCM_TACO(0xff) | \
+ FTIM1_GPCM_TRAD(0x3f))
+#define CONFIG_SYS_CS3_FTIM2 (FTIM2_GPCM_TCS(0x0e) | \
+ FTIM2_GPCM_TCH(0x8) | \
+ FTIM2_GPCM_TWP(0x1f))
+#define CONFIG_SYS_CS3_FTIM3 0x0
+
+#define CONFIG_NAND_FSL_IFC
+#define CONFIG_SYS_NAND_BASE 0xff800000
+#ifdef CONFIG_PHYS_64BIT
+#define CONFIG_SYS_NAND_BASE_PHYS (0xf00000000ull | CONFIG_SYS_NAND_BASE)
+#else
+#define CONFIG_SYS_NAND_BASE_PHYS CONFIG_SYS_NAND_BASE
+#endif
+#define CONFIG_SYS_NAND_CSPR_EXT (0xf)
+#define CONFIG_SYS_NAND_CSPR (CSPR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \
+ | CSPR_PORT_SIZE_8 /* Port Size = 8 bit */ \
+ | CSPR_MSEL_NAND /* MSEL = NAND */ \
+ | CSPR_V)
+#define CONFIG_SYS_NAND_AMASK IFC_AMASK(64*1024)
+
+#define CONFIG_SYS_NAND_CSOR (CSOR_NAND_ECC_ENC_EN /* ECC on encode */ \
+ | CSOR_NAND_ECC_DEC_EN /* ECC on decode */ \
+ | CSOR_NAND_ECC_MODE_4 /* 4-bit ECC */ \
+ | CSOR_NAND_RAL_3 /* RAL = 3Byes */ \
+ | CSOR_NAND_PGS_2K /* Page Size = 2K */ \
+ | CSOR_NAND_SPRZ_64/* Spare size = 64 */ \
+ | CSOR_NAND_PB(64)) /*Pages Per Block = 64*/
+
+#define CONFIG_SYS_NAND_ONFI_DETECTION
+
+/* ONFI NAND Flash mode0 Timing Params */
+#define CONFIG_SYS_NAND_FTIM0 (FTIM0_NAND_TCCST(0x07) | \
+ FTIM0_NAND_TWP(0x18) | \
+ FTIM0_NAND_TWCHT(0x07) | \
+ FTIM0_NAND_TWH(0x0a))
+#define CONFIG_SYS_NAND_FTIM1 (FTIM1_NAND_TADLE(0x32) | \
+ FTIM1_NAND_TWBE(0x39) | \
+ FTIM1_NAND_TRR(0x0e) | \
+ FTIM1_NAND_TRP(0x18))
+#define CONFIG_SYS_NAND_FTIM2 (FTIM2_NAND_TRAD(0x0f) | \
+ FTIM2_NAND_TREH(0x0a) | \
+ FTIM2_NAND_TWHRE(0x1e))
+#define CONFIG_SYS_NAND_FTIM3 0x0
+
+#define CONFIG_SYS_NAND_DDR_LAW 11
+#define CONFIG_SYS_NAND_BASE_LIST { CONFIG_SYS_NAND_BASE }
+#define CONFIG_SYS_MAX_NAND_DEVICE 1
+#define CONFIG_MTD_NAND_VERIFY_WRITE
+#define CONFIG_CMD_NAND
+
+#define CONFIG_SYS_NAND_BLOCK_SIZE (128 * 1024)
+
+#if defined(CONFIG_NAND)
+#define CONFIG_SYS_CSPR0_EXT CONFIG_SYS_NAND_CSPR_EXT
+#define CONFIG_SYS_CSPR0 CONFIG_SYS_NAND_CSPR
+#define CONFIG_SYS_AMASK0 CONFIG_SYS_NAND_AMASK
+#define CONFIG_SYS_CSOR0 CONFIG_SYS_NAND_CSOR
+#define CONFIG_SYS_CS0_FTIM0 CONFIG_SYS_NAND_FTIM0
+#define CONFIG_SYS_CS0_FTIM1 CONFIG_SYS_NAND_FTIM1
+#define CONFIG_SYS_CS0_FTIM2 CONFIG_SYS_NAND_FTIM2
+#define CONFIG_SYS_CS0_FTIM3 CONFIG_SYS_NAND_FTIM3
+#define CONFIG_SYS_CSPR1_EXT CONFIG_SYS_NOR0_CSPR_EXT
+#define CONFIG_SYS_CSPR1 CONFIG_SYS_NOR0_CSPR
+#define CONFIG_SYS_AMASK1 CONFIG_SYS_NOR_AMASK
+#define CONFIG_SYS_CSOR1 CONFIG_SYS_NOR_CSOR
+#define CONFIG_SYS_CS1_FTIM0 CONFIG_SYS_NOR_FTIM0
+#define CONFIG_SYS_CS1_FTIM1 CONFIG_SYS_NOR_FTIM1
+#define CONFIG_SYS_CS1_FTIM2 CONFIG_SYS_NOR_FTIM2
+#define CONFIG_SYS_CS1_FTIM3 CONFIG_SYS_NOR_FTIM3
+#define CONFIG_SYS_CSPR2_EXT CONFIG_SYS_NOR1_CSPR_EXT
+#define CONFIG_SYS_CSPR2 CONFIG_SYS_NOR1_CSPR
+#define CONFIG_SYS_AMASK2 CONFIG_SYS_NOR_AMASK
+#define CONFIG_SYS_CSOR2 CONFIG_SYS_NOR_CSOR
+#define CONFIG_SYS_CS2_FTIM0 CONFIG_SYS_NOR_FTIM0
+#define CONFIG_SYS_CS2_FTIM1 CONFIG_SYS_NOR_FTIM1
+#define CONFIG_SYS_CS2_FTIM2 CONFIG_SYS_NOR_FTIM2
+#define CONFIG_SYS_CS2_FTIM3 CONFIG_SYS_NOR_FTIM3
+#else
+#define CONFIG_SYS_CSPR0_EXT CONFIG_SYS_NOR0_CSPR_EXT
+#define CONFIG_SYS_CSPR0 CONFIG_SYS_NOR0_CSPR
+#define CONFIG_SYS_AMASK0 CONFIG_SYS_NOR_AMASK
+#define CONFIG_SYS_CSOR0 CONFIG_SYS_NOR_CSOR
+#define CONFIG_SYS_CS0_FTIM0 CONFIG_SYS_NOR_FTIM0
+#define CONFIG_SYS_CS0_FTIM1 CONFIG_SYS_NOR_FTIM1
+#define CONFIG_SYS_CS0_FTIM2 CONFIG_SYS_NOR_FTIM2
+#define CONFIG_SYS_CS0_FTIM3 CONFIG_SYS_NOR_FTIM3
+#define CONFIG_SYS_CSPR1_EXT CONFIG_SYS_NOR1_CSPR_EXT
+#define CONFIG_SYS_CSPR1 CONFIG_SYS_NOR1_CSPR
+#define CONFIG_SYS_AMASK1 CONFIG_SYS_NOR_AMASK
+#define CONFIG_SYS_CSOR1 CONFIG_SYS_NOR_CSOR
+#define CONFIG_SYS_CS1_FTIM0 CONFIG_SYS_NOR_FTIM0
+#define CONFIG_SYS_CS1_FTIM1 CONFIG_SYS_NOR_FTIM1
+#define CONFIG_SYS_CS1_FTIM2 CONFIG_SYS_NOR_FTIM2
+#define CONFIG_SYS_CS1_FTIM3 CONFIG_SYS_NOR_FTIM3
+#define CONFIG_SYS_CSPR2_EXT CONFIG_SYS_NAND_CSPR_EXT
+#define CONFIG_SYS_CSPR2 CONFIG_SYS_NAND_CSPR
+#define CONFIG_SYS_AMASK2 CONFIG_SYS_NAND_AMASK
+#define CONFIG_SYS_CSOR2 CONFIG_SYS_NAND_CSOR
+#define CONFIG_SYS_CS2_FTIM0 CONFIG_SYS_NAND_FTIM0
+#define CONFIG_SYS_CS2_FTIM1 CONFIG_SYS_NAND_FTIM1
+#define CONFIG_SYS_CS2_FTIM2 CONFIG_SYS_NAND_FTIM2
+#define CONFIG_SYS_CS2_FTIM3 CONFIG_SYS_NAND_FTIM3
+#endif
+
+#ifdef CONFIG_SPL_BUILD
+#define CONFIG_SYS_MONITOR_BASE CONFIG_SPL_TEXT_BASE
+#else
+#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE
+#endif
+
+#if defined(CONFIG_RAMBOOT_PBL)
+#define CONFIG_SYS_RAMBOOT
+#endif
+
+#define CONFIG_BOARD_EARLY_INIT_R
+#define CONFIG_MISC_INIT_R
+
+#define CONFIG_HWCONFIG
+
+/* define to use L1 as initial stack */
+#define CONFIG_L1_INIT_RAM
+#define CONFIG_SYS_INIT_RAM_LOCK
+#define CONFIG_SYS_INIT_RAM_ADDR 0xfdd00000 /* Initial L1 address */
+#ifdef CONFIG_PHYS_64BIT
+#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0xf
+#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW 0xfe0ec000
+/* The assembler doesn't like typecast */
+#define CONFIG_SYS_INIT_RAM_ADDR_PHYS \
+ ((CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH * 1ull << 32) | \
+ CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW)
+#else
+#define CONFIG_SYS_INIT_RAM_ADDR_PHYS 0xfe0ec000 /* Initial L1 address */
+#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0
+#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW CONFIG_SYS_INIT_RAM_ADDR_PHYS
+#endif
+#define CONFIG_SYS_INIT_RAM_SIZE 0x00004000
+
+#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - \
+ GENERATED_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
+
+#define CONFIG_SYS_MONITOR_LEN (768 * 1024)
+#define CONFIG_SYS_MALLOC_LEN (10 * 1024 * 1024)
+
+/* Serial Port */
+#define CONFIG_CONS_INDEX 1
+#define CONFIG_SYS_NS16550
+#define CONFIG_SYS_NS16550_SERIAL
+#define CONFIG_SYS_NS16550_REG_SIZE 1
+#define CONFIG_SYS_NS16550_CLK (get_bus_freq(0)/2)
+
+#define CONFIG_SYS_BAUDRATE_TABLE \
+ {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
+
+#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x11C500)
+#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x11C600)
+#define CONFIG_SYS_NS16550_COM3 (CONFIG_SYS_CCSRBAR+0x11D500)
+#define CONFIG_SYS_NS16550_COM4 (CONFIG_SYS_CCSRBAR+0x11D600)
+#define CONFIG_SYS_CONSOLE_IS_IN_ENV /* determine from environment */
+
+/* Use the HUSH parser */
+#define CONFIG_SYS_HUSH_PARSER
+#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
+
+/* Video */
+#ifdef CONFIG_PPC_T1024 /* no DIU on T1023 */
+#define CONFIG_FSL_DIU_FB
+#ifdef CONFIG_FSL_DIU_FB
+#define CONFIG_FSL_DIU_CH7301
+#define CONFIG_SYS_DIU_ADDR (CONFIG_SYS_CCSRBAR + 0x180000)
+#define CONFIG_VIDEO
+#define CONFIG_CMD_BMP
+#define CONFIG_CFB_CONSOLE
+#define CONFIG_VIDEO_SW_CURSOR
+#define CONFIG_VGA_AS_SINGLE_DEVICE
+#define CONFIG_VIDEO_LOGO
+#define CONFIG_VIDEO_BMP_LOGO
+#define CONFIG_CFI_FLASH_USE_WEAK_ACCESSORS
+/*
+ * With CONFIG_CFI_FLASH_USE_WEAK_ACCESSORS, flash I/O is really slow, so
+ * disable empty flash sector detection, which is I/O-intensive.
+ */
+#undef CONFIG_SYS_FLASH_EMPTY_INFO
+#endif
+#endif
+
+/* pass open firmware flat tree */
+#define CONFIG_OF_LIBFDT
+#define CONFIG_OF_BOARD_SETUP
+#define CONFIG_OF_STDOUT_VIA_ALIAS
+
+/* new uImage format support */
+#define CONFIG_FIT
+#define CONFIG_FIT_VERBOSE /* enable fit_format_{error,warning}() */
+
+/* I2C */
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_FSL /* Use FSL common I2C driver */
+#define CONFIG_SYS_FSL_I2C_SPEED 50000 /* I2C speed in Hz */
+#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
+#define CONFIG_SYS_FSL_I2C2_SPEED 50000 /* I2C speed in Hz */
+#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F
+#define CONFIG_SYS_FSL_I2C_OFFSET 0x118000
+#define CONFIG_SYS_FSL_I2C2_OFFSET 0x118100
+
+#define I2C_MUX_PCA_ADDR 0x77
+#define I2C_MUX_PCA_ADDR_PRI 0x77 /* Primary Mux*/
+#define I2C_MUX_PCA_ADDR_SEC 0x76 /* Secondary multiplexer */
+#define I2C_RETIMER_ADDR 0x18
+
+/* I2C bus multiplexer */
+#define I2C_MUX_CH_DEFAULT 0x8
+#define I2C_MUX_CH_DIU 0xC
+#define I2C_MUX_CH5 0xD
+#define I2C_MUX_CH7 0xF
+
+/* LDI/DVI Encoder for display */
+#define CONFIG_SYS_I2C_LDI_ADDR 0x38
+#define CONFIG_SYS_I2C_DVI_ADDR 0x75
+
+/*
+ * RTC configuration
+ */
+#define RTC
+#define CONFIG_RTC_DS3231 1
+#define CONFIG_SYS_I2C_RTC_ADDR 0x68
+
+/*
+ * eSPI - Enhanced SPI
+ */
+#define CONFIG_FSL_ESPI
+#define CONFIG_SPI_FLASH
+#define CONFIG_SPI_FLASH_STMICRO
+#ifndef CONFIG_SPL_BUILD
+#define CONFIG_SPI_FLASH_SST
+#define CONFIG_SPI_FLASH_EON
+#endif
+#define CONFIG_CMD_SF
+#define CONFIG_SPI_FLASH_BAR
+#define CONFIG_SF_DEFAULT_SPEED 10000000
+#define CONFIG_SF_DEFAULT_MODE 0
+
+/*
+ * General PCIe
+ * Memory space is mapped 1-1, but I/O space must start from 0.
+ */
+#define CONFIG_PCI /* Enable PCI/PCIE */
+#define CONFIG_PCIE1 /* PCIE controler 1 */
+#define CONFIG_PCIE2 /* PCIE controler 2 */
+#define CONFIG_PCIE3 /* PCIE controler 3 */
+#define CONFIG_FSL_PCI_INIT /* Use common FSL init code */
+#define CONFIG_SYS_PCI_64BIT /* enable 64-bit PCI resources */
+#define CONFIG_PCI_INDIRECT_BRIDGE
+
+#ifdef CONFIG_PCI
+/* controller 1, direct to uli, tgtid 3, Base address 20000 */
+#ifdef CONFIG_PCIE1
+#define CONFIG_SYS_PCIE1_MEM_VIRT 0x80000000
+#ifdef CONFIG_PHYS_64BIT
+#define CONFIG_SYS_PCIE1_MEM_BUS 0xe0000000
+#define CONFIG_SYS_PCIE1_MEM_PHYS 0xc00000000ull
+#else
+#define CONFIG_SYS_PCIE1_MEM_BUS 0x80000000
+#define CONFIG_SYS_PCIE1_MEM_PHYS 0x80000000
+#endif
+#define CONFIG_SYS_PCIE1_MEM_SIZE 0x10000000 /* 256M */
+#define CONFIG_SYS_PCIE1_IO_VIRT 0xf8000000
+#define CONFIG_SYS_PCIE1_IO_BUS 0x00000000
+#ifdef CONFIG_PHYS_64BIT
+#define CONFIG_SYS_PCIE1_IO_PHYS 0xff8000000ull
+#else
+#define CONFIG_SYS_PCIE1_IO_PHYS 0xf8000000
+#endif
+#define CONFIG_SYS_PCIE1_IO_SIZE 0x00010000 /* 64k */
+#endif
+
+/* controller 2, Slot 2, tgtid 2, Base address 201000 */
+#ifdef CONFIG_PCIE2
+#define CONFIG_SYS_PCIE2_MEM_VIRT 0x90000000
+#ifdef CONFIG_PHYS_64BIT
+#define CONFIG_SYS_PCIE2_MEM_BUS 0xe0000000
+#define CONFIG_SYS_PCIE2_MEM_PHYS 0xc10000000ull
+#else
+#define CONFIG_SYS_PCIE2_MEM_BUS 0x90000000
+#define CONFIG_SYS_PCIE2_MEM_PHYS 0x90000000
+#endif
+#define CONFIG_SYS_PCIE2_MEM_SIZE 0x10000000 /* 256M */
+#define CONFIG_SYS_PCIE2_IO_VIRT 0xf8010000
+#define CONFIG_SYS_PCIE2_IO_BUS 0x00000000
+#ifdef CONFIG_PHYS_64BIT
+#define CONFIG_SYS_PCIE2_IO_PHYS 0xff8010000ull
+#else
+#define CONFIG_SYS_PCIE2_IO_PHYS 0xf8010000
+#endif
+#define CONFIG_SYS_PCIE2_IO_SIZE 0x00010000 /* 64k */
+#endif
+
+/* controller 3, Slot 1, tgtid 1, Base address 202000 */
+#ifdef CONFIG_PCIE3
+#define CONFIG_SYS_PCIE3_MEM_VIRT 0xa0000000
+#ifdef CONFIG_PHYS_64BIT
+#define CONFIG_SYS_PCIE3_MEM_BUS 0xe0000000
+#define CONFIG_SYS_PCIE3_MEM_PHYS 0xc20000000ull
+#else
+#define CONFIG_SYS_PCIE3_MEM_BUS 0xa0000000
+#define CONFIG_SYS_PCIE3_MEM_PHYS 0xa0000000
+#endif
+#define CONFIG_SYS_PCIE3_MEM_SIZE 0x10000000 /* 256M */
+#define CONFIG_SYS_PCIE3_IO_VIRT 0xf8020000
+#define CONFIG_SYS_PCIE3_IO_BUS 0x00000000
+#ifdef CONFIG_PHYS_64BIT
+#define CONFIG_SYS_PCIE3_IO_PHYS 0xff8020000ull
+#else
+#define CONFIG_SYS_PCIE3_IO_PHYS 0xf8020000
+#endif
+#define CONFIG_SYS_PCIE3_IO_SIZE 0x00010000 /* 64k */
+#endif
+
+#define CONFIG_PCI_PNP /* do pci plug-and-play */
+#define CONFIG_E1000
+#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
+#define CONFIG_DOS_PARTITION
+#endif /* CONFIG_PCI */
+
+/*
+ *SATA
+ */
+#define CONFIG_FSL_SATA_V2
+#ifdef CONFIG_FSL_SATA_V2
+#define CONFIG_LIBATA
+#define CONFIG_FSL_SATA
+#define CONFIG_SYS_SATA_MAX_DEVICE 1
+#define CONFIG_SATA1
+#define CONFIG_SYS_SATA1 CONFIG_SYS_MPC85xx_SATA1_ADDR
+#define CONFIG_SYS_SATA1_FLAGS FLAGS_DMA
+#define CONFIG_LBA48
+#define CONFIG_CMD_SATA
+#define CONFIG_DOS_PARTITION
+#define CONFIG_CMD_EXT2
+#endif
+
+/*
+ * USB
+ */
+#define CONFIG_HAS_FSL_DR_USB
+
+#ifdef CONFIG_HAS_FSL_DR_USB
+#define CONFIG_USB_EHCI
+#define CONFIG_CMD_USB
+#define CONFIG_USB_STORAGE
+#define CONFIG_USB_EHCI_FSL
+#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
+#define CONFIG_CMD_EXT2
+#endif
+
+/*
+ * SDHC
+ */
+#define CONFIG_MMC
+#ifdef CONFIG_MMC
+#define CONFIG_FSL_ESDHC
+#define CONFIG_SYS_FSL_ESDHC_ADDR CONFIG_SYS_MPC85xx_ESDHC_ADDR
+#define CONFIG_CMD_MMC
+#define CONFIG_GENERIC_MMC
+#define CONFIG_CMD_EXT2
+#define CONFIG_CMD_FAT
+#define CONFIG_DOS_PARTITION
+#endif
+
+/* Qman/Bman */
+#ifndef CONFIG_NOBQFMAN
+#define CONFIG_SYS_DPAA_QBMAN /* Support Q/Bman */
+#define CONFIG_SYS_BMAN_NUM_PORTALS 25
+#define CONFIG_SYS_BMAN_MEM_BASE 0xf4000000
+#ifdef CONFIG_PHYS_64BIT
+#define CONFIG_SYS_BMAN_MEM_PHYS 0xff4000000ull
+#else
+#define CONFIG_SYS_BMAN_MEM_PHYS CONFIG_SYS_BMAN_MEM_BASE
+#endif
+#define CONFIG_SYS_BMAN_MEM_SIZE 0x02000000
+#define CONFIG_SYS_QMAN_NUM_PORTALS 25
+#define CONFIG_SYS_QMAN_MEM_BASE 0xf6000000
+#ifdef CONFIG_PHYS_64BIT
+#define CONFIG_SYS_QMAN_MEM_PHYS 0xff6000000ull
+#else
+#define CONFIG_SYS_QMAN_MEM_PHYS CONFIG_SYS_QMAN_MEM_BASE
+#endif
+#define CONFIG_SYS_QMAN_MEM_SIZE 0x02000000
+
+#define CONFIG_SYS_DPAA_FMAN
+
+#define CONFIG_QE
+#define CONFIG_U_QE
+/* Default address of microcode for the Linux FMan driver */
+#if defined(CONFIG_SPIFLASH)
+/*
+ * env is stored at 0x100000, sector size is 0x10000, ucode is stored after
+ * env, so we got 0x110000.
+ */
+#define CONFIG_SYS_QE_FW_IN_SPIFLASH
+#define CONFIG_SYS_FMAN_FW_ADDR 0x110000
+#define CONFIG_SYS_QE_FW_ADDR 0x130000
+#elif defined(CONFIG_SDCARD)
+/*
+ * PBL SD boot image should stored at 0x1000(8 blocks), the size of the image is
+ * about 1MB (2048 blocks), Env is stored after the image, and the env size is
+ * 0x2000 (16 blocks), 8 + 2048 + 16 = 2072, enlarge it to 2080(0x820).
+ */
+#define CONFIG_SYS_QE_FMAN_FW_IN_MMC
+#define CONFIG_SYS_FMAN_FW_ADDR (512 * 0x820)
+#define CONFIG_SYS_QE_FW_ADDR (512 * 0x920)
+#elif defined(CONFIG_NAND)
+#define CONFIG_SYS_QE_FMAN_FW_IN_NAND
+#define CONFIG_SYS_FMAN_FW_ADDR (11 * CONFIG_SYS_NAND_BLOCK_SIZE)
+#define CONFIG_SYS_QE_FW_ADDR (12 * CONFIG_SYS_NAND_BLOCK_SIZE)
+#elif defined(CONFIG_SRIO_PCIE_BOOT_SLAVE)
+/*
+ * Slave has no ucode locally, it can fetch this from remote. When implementing
+ * in two corenet boards, slave's ucode could be stored in master's memory
+ * space, the address can be mapped from slave TLB->slave LAW->
+ * slave SRIO or PCIE outbound window->master inbound window->
+ * master LAW->the ucode address in master's memory space.
+ */
+#define CONFIG_SYS_QE_FMAN_FW_IN_REMOTE
+#define CONFIG_SYS_FMAN_FW_ADDR 0xFFE00000
+#else
+#define CONFIG_SYS_QE_FMAN_FW_IN_NOR
+#define CONFIG_SYS_FMAN_FW_ADDR 0xEFF00000
+#define CONFIG_SYS_QE_FW_ADDR 0xEFE00000
+#endif
+#define CONFIG_SYS_QE_FMAN_FW_LENGTH 0x10000
+#define CONFIG_SYS_FDT_PAD (0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH)
+#endif /* CONFIG_NOBQFMAN */
+
+#ifdef CONFIG_SYS_DPAA_FMAN
+#define CONFIG_FMAN_ENET
+#define CONFIG_PHYLIB_10G
+#define CONFIG_PHY_VITESSE
+#define CONFIG_PHY_REALTEK
+#define CONFIG_PHY_TERANETICS
+#define RGMII_PHY1_ADDR 0x1
+#define RGMII_PHY2_ADDR 0x2
+#define SGMII_CARD_AQ_PHY_ADDR_S3 0x3
+#define SGMII_CARD_AQ_PHY_ADDR_S4 0x4
+#define SGMII_CARD_AQ_PHY_ADDR_S5 0x5
+#define SGMII_CARD_PORT1_PHY_ADDR 0x1C
+#define SGMII_CARD_PORT2_PHY_ADDR 0x1D
+#define SGMII_CARD_PORT3_PHY_ADDR 0x1E
+#define SGMII_CARD_PORT4_PHY_ADDR 0x1F
+#endif
+
+#ifdef CONFIG_FMAN_ENET
+#define CONFIG_MII /* MII PHY management */
+#define CONFIG_ETHPRIME "FM1@DTSEC4"
+#define CONFIG_PHY_GIGE /* Include GbE speed/duplex detection */
+#endif
+
+/*
+ * Dynamic MTD Partition support with mtdparts
+ */
+#ifndef CONFIG_SYS_NO_FLASH
+#define CONFIG_MTD_DEVICE
+#define CONFIG_MTD_PARTITIONS
+#define CONFIG_CMD_MTDPARTS
+#define CONFIG_FLASH_CFI_MTD
+#define MTDIDS_DEFAULT "nor0=fe8000000.nor,nand0=fff800000.flash," \
+ "spi0=spife110000.0"
+#define MTDPARTS_DEFAULT "mtdparts=fe8000000.nor:1m(uboot),5m(kernel)," \
+ "128k(dtb),96m(fs),-(user);"\
+ "fff800000.flash:2m(uboot),9m(kernel),"\
+ "128k(dtb),96m(fs),-(user);spife110000.0:" \
+ "2m(uboot),9m(kernel),128k(dtb),-(user)"
+#endif
+
+/*
+ * Environment
+ */
+#define CONFIG_LOADS_ECHO /* echo on for serial download */
+#define CONFIG_SYS_LOADS_BAUD_CHANGE /* allow baudrate change */
+
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_DATE
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_EEPROM
+#define CONFIG_CMD_ELF
+#define CONFIG_CMD_ERRATA
+#define CONFIG_CMD_GREPENV
+#define CONFIG_CMD_IRQ
+#define CONFIG_CMD_I2C
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_REGINFO
+#define CONFIG_CMD_SETEXPR
+
+#ifdef CONFIG_PCI
+#define CONFIG_CMD_PCI
+#define CONFIG_CMD_NET
+#endif
+
+/*
+ * Miscellaneous configurable options
+ */
+#define CONFIG_SYS_LONGHELP /* undef to save memory */
+#define CONFIG_CMDLINE_EDITING /* Command-line editing */
+#define CONFIG_AUTO_COMPLETE /* add autocompletion support */
+#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */
+#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */
+#ifdef CONFIG_CMD_KGDB
+#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
+#else
+#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
+#endif
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16)
+#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
+#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 64 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CONFIG_SYS_BOOTMAPSZ (64 << 20) /* Initial map for Linux*/
+#define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */
+
+#ifdef CONFIG_CMD_KGDB
+#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
+#endif
+
+/*
+ * Environment Configuration
+ */
+#define CONFIG_ROOTPATH "/opt/nfsroot"
+#define CONFIG_BOOTFILE "uImage"
+#define CONFIG_UBOOTPATH "u-boot.bin" /* U-Boot image on TFTP server */
+#define CONFIG_LOADADDR 1000000 /* default location for tftp, bootm */
+#define CONFIG_BOOTDELAY 10 /* -1 disables auto-boot */
+#define CONFIG_BAUDRATE 115200
+#define __USB_PHY_TYPE utmi
+
+
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ "hwconfig=fsl_ddr:ctlr_intlv=cacheline,bank_intlv=cs0_cs1;\0" \
+ "usb1:dr_mode=host,phy_type=" __stringify(__USB_PHY_TYPE) "\0" \
+ "bootargs=root=/dev/ram rw console=ttyS0,115200\0" \
+ "ramdiskfile=t1024qds/ramdisk.uboot\0" \
+ "fdtfile=t1024qds/t1024qds.dtb\0" \
+ "netdev=eth0\0" \
+ "video-mode=fslfb:1024x768-32@60,monitor=dvi\0" \
+ "uboot=" __stringify(CONFIG_UBOOTPATH) "\0" \
+ "ubootaddr=" __stringify(CONFIG_SYS_TEXT_BASE) "\0" \
+ "tftpflash=tftpboot $loadaddr $uboot && " \
+ "protect off $ubootaddr +$filesize && " \
+ "erase $ubootaddr +$filesize && " \
+ "cp.b $loadaddr $ubootaddr $filesize && " \
+ "protect on $ubootaddr +$filesize && " \
+ "cmp.b $loadaddr $ubootaddr $filesize\0" \
+ "consoledev=ttyS0\0" \
+ "ramdiskaddr=2000000\0" \
+ "fdtaddr=d00000\0" \
+ "bdev=sda3\0"
+
+#define CONFIG_LINUX \
+ "setenv bootargs root=/dev/ram rw " \
+ "console=$consoledev,$baudrate $othbootargs;" \
+ "setenv ramdiskaddr 0x02000000;" \
+ "setenv fdtaddr 0x00c00000;" \
+ "setenv loadaddr 0x1000000;" \
+ "bootm $loadaddr $ramdiskaddr $fdtaddr"
+
+#define CONFIG_NFSBOOTCOMMAND \
+ "setenv bootargs root=/dev/nfs rw " \
+ "nfsroot=$serverip:$rootpath " \
+ "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
+ "console=$consoledev,$baudrate $othbootargs;" \
+ "tftp $loadaddr $bootfile;" \
+ "tftp $fdtaddr $fdtfile;" \
+ "bootm $loadaddr - $fdtaddr"
+
+#define CONFIG_BOOTCOMMAND CONFIG_LINUX
+
+#ifdef CONFIG_SECURE_BOOT
+#include <asm/fsl_secure_boot.h>
+#endif
+
+#endif /* __T1024QDS_H */
diff --git a/include/configs/T102xRDB.h b/include/configs/T102xRDB.h
new file mode 100644
index 0000000..6f1fcd6
--- /dev/null
+++ b/include/configs/T102xRDB.h
@@ -0,0 +1,896 @@
+/*
+ * Copyright 2014 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+/*
+ * T1024/T1023 RDB board configuration file
+ */
+
+#ifndef __T1024RDB_H
+#define __T1024RDB_H
+
+/* High Level Configuration Options */
+#define CONFIG_SYS_GENERIC_BOARD
+#define CONFIG_DISPLAY_BOARDINFO
+#define CONFIG_BOOKE
+#define CONFIG_E500 /* BOOKE e500 family */
+#define CONFIG_E500MC /* BOOKE e500mc family */
+#define CONFIG_SYS_BOOK3E_HV /* Category E.HV supported */
+#define CONFIG_MP /* support multiple processors */
+#define CONFIG_PHYS_64BIT
+#define CONFIG_ENABLE_36BIT_PHYS
+
+#ifdef CONFIG_PHYS_64BIT
+#define CONFIG_ADDR_MAP 1
+#define CONFIG_SYS_NUM_ADDR_MAP 64 /* number of TLB1 entries */
+#endif
+
+#define CONFIG_SYS_FSL_CPC /* Corenet Platform Cache */
+#define CONFIG_SYS_NUM_CPC CONFIG_NUM_DDR_CONTROLLERS
+#define CONFIG_FSL_IFC /* Enable IFC Support */
+
+#define CONFIG_FSL_LAW /* Use common FSL init code */
+#define CONFIG_ENV_OVERWRITE
+
+/* support deep sleep */
+#define CONFIG_DEEP_SLEEP
+#define CONFIG_SILENT_CONSOLE
+
+#ifdef CONFIG_RAMBOOT_PBL
+#define CONFIG_SYS_FSL_PBL_PBI board/freescale/t102xrdb/t1024_pbi.cfg
+#define CONFIG_SYS_FSL_PBL_RCW board/freescale/t102xrdb/t1024_rcw.cfg
+#define CONFIG_SPL_MPC8XXX_INIT_DDR_SUPPORT
+#define CONFIG_SPL_ENV_SUPPORT
+#define CONFIG_SPL_SERIAL_SUPPORT
+#define CONFIG_SPL_FLUSH_IMAGE
+#define CONFIG_SPL_TARGET "u-boot-with-spl.bin"
+#define CONFIG_SPL_LIBGENERIC_SUPPORT
+#define CONFIG_SPL_LIBCOMMON_SUPPORT
+#define CONFIG_SPL_I2C_SUPPORT
+#define CONFIG_SPL_DRIVERS_MISC_SUPPORT
+#define CONFIG_FSL_LAW /* Use common FSL init code */
+#define CONFIG_SYS_TEXT_BASE 0x00201000
+#define CONFIG_SPL_TEXT_BASE 0xFFFD8000
+#define CONFIG_SPL_PAD_TO 0x40000
+#define CONFIG_SPL_MAX_SIZE 0x28000
+#define RESET_VECTOR_OFFSET 0x27FFC
+#define BOOT_PAGE_OFFSET 0x27000
+#ifdef CONFIG_SPL_BUILD
+#define CONFIG_SPL_SKIP_RELOCATE
+#define CONFIG_SPL_COMMON_INIT_DDR
+#define CONFIG_SYS_CCSR_DO_NOT_RELOCATE
+#define CONFIG_SYS_NO_FLASH
+#endif
+
+#ifdef CONFIG_NAND
+#define CONFIG_SPL_NAND_SUPPORT
+#define CONFIG_SYS_NAND_U_BOOT_SIZE (768 << 10)
+#define CONFIG_SYS_NAND_U_BOOT_DST 0x00200000
+#define CONFIG_SYS_NAND_U_BOOT_START 0x00200000
+#define CONFIG_SYS_NAND_U_BOOT_OFFS (256 << 10)
+#define CONFIG_SYS_LDSCRIPT "arch/powerpc/cpu/mpc85xx/u-boot-nand.lds"
+#define CONFIG_SPL_NAND_BOOT
+#endif
+
+#ifdef CONFIG_SPIFLASH
+#define CONFIG_RESET_VECTOR_ADDRESS 0x200FFC
+#define CONFIG_SPL_SPI_SUPPORT
+#define CONFIG_SPL_SPI_FLASH_SUPPORT
+#define CONFIG_SPL_SPI_FLASH_MINIMAL
+#define CONFIG_SYS_SPI_FLASH_U_BOOT_SIZE (768 << 10)
+#define CONFIG_SYS_SPI_FLASH_U_BOOT_DST (0x00200000)
+#define CONFIG_SYS_SPI_FLASH_U_BOOT_START (0x00200000)
+#define CONFIG_SYS_SPI_FLASH_U_BOOT_OFFS (256 << 10)
+#define CONFIG_SYS_LDSCRIPT "arch/powerpc/cpu/mpc85xx/u-boot.lds"
+#ifndef CONFIG_SPL_BUILD
+#define CONFIG_SYS_MPC85XX_NO_RESETVEC
+#endif
+#define CONFIG_SPL_SPI_BOOT
+#endif
+
+#ifdef CONFIG_SDCARD
+#define CONFIG_RESET_VECTOR_ADDRESS 0x200FFC
+#define CONFIG_SPL_MMC_SUPPORT
+#define CONFIG_SPL_MMC_MINIMAL
+#define CONFIG_SYS_MMC_U_BOOT_SIZE (768 << 10)
+#define CONFIG_SYS_MMC_U_BOOT_DST (0x00200000)
+#define CONFIG_SYS_MMC_U_BOOT_START (0x00200000)
+#define CONFIG_SYS_MMC_U_BOOT_OFFS (260 << 10)
+#define CONFIG_SYS_LDSCRIPT "arch/powerpc/cpu/mpc85xx/u-boot.lds"
+#ifndef CONFIG_SPL_BUILD
+#define CONFIG_SYS_MPC85XX_NO_RESETVEC
+#endif
+#define CONFIG_SPL_MMC_BOOT
+#endif
+
+#endif /* CONFIG_RAMBOOT_PBL */
+
+#ifndef CONFIG_SYS_TEXT_BASE
+#define CONFIG_SYS_TEXT_BASE 0xeff40000
+#endif
+
+#ifndef CONFIG_RESET_VECTOR_ADDRESS
+#define CONFIG_RESET_VECTOR_ADDRESS 0xeffffffc
+#endif
+
+#ifndef CONFIG_SYS_NO_FLASH
+#define CONFIG_FLASH_CFI_DRIVER
+#define CONFIG_SYS_FLASH_CFI
+#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
+#endif
+
+/* PCIe Boot - Master */
+#define CONFIG_SRIO_PCIE_BOOT_MASTER
+/*
+ * for slave u-boot IMAGE instored in master memory space,
+ * PHYS must be aligned based on the SIZE
+ */
+#define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS1 0xfff00000ull
+#define CONFIG_SRIO_PCIE_BOOT_IMAGE_SIZE 0x100000 /* 1M */
+#ifdef CONFIG_PHYS_64BIT
+#define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_PHYS 0xfef200000ull
+#define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS2 0x3fff00000ull
+#else
+#define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_PHYS 0xef200000
+#define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS2 0xfff00000
+#endif
+/*
+ * for slave UCODE and ENV instored in master memory space,
+ * PHYS must be aligned based on the SIZE
+ */
+#ifdef CONFIG_PHYS_64BIT
+#define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_PHYS 0xfef100000ull
+#define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_BUS 0x3ffe00000ull
+#else
+#define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_PHYS 0xef100000
+#define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_BUS 0xffe00000
+#endif
+#define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_SIZE 0x40000 /* 256K */
+/* slave core release by master*/
+#define CONFIG_SRIO_PCIE_BOOT_BRR_OFFSET 0xe00e4
+#define CONFIG_SRIO_PCIE_BOOT_RELEASE_MASK 0x00000001 /* release core 0 */
+
+/* PCIe Boot - Slave */
+#ifdef CONFIG_SRIO_PCIE_BOOT_SLAVE
+#define CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR 0xFFE00000
+#define CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR_PHYS \
+ (0x300000000ull | CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR)
+/* Set 1M boot space for PCIe boot */
+#define CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR (CONFIG_SYS_TEXT_BASE & 0xfff00000)
+#define CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR_PHYS \
+ (0x300000000ull | CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR)
+#define CONFIG_RESET_VECTOR_ADDRESS 0xfffffffc
+#define CONFIG_SYS_NO_FLASH
+#endif
+
+#if defined(CONFIG_SPIFLASH)
+#define CONFIG_SYS_EXTRA_ENV_RELOC
+#define CONFIG_ENV_IS_IN_SPI_FLASH
+#define CONFIG_ENV_SPI_BUS 0
+#define CONFIG_ENV_SPI_CS 0
+#define CONFIG_ENV_SPI_MAX_HZ 10000000
+#define CONFIG_ENV_SPI_MODE 0
+#define CONFIG_ENV_SIZE 0x2000 /* 8KB */
+#define CONFIG_ENV_OFFSET 0x100000 /* 1MB */
+#define CONFIG_ENV_SECT_SIZE 0x10000
+#elif defined(CONFIG_SDCARD)
+#define CONFIG_SYS_EXTRA_ENV_RELOC
+#define CONFIG_ENV_IS_IN_MMC
+#define CONFIG_SYS_MMC_ENV_DEV 0
+#define CONFIG_ENV_SIZE 0x2000
+#define CONFIG_ENV_OFFSET (512 * 0x800)
+#elif defined(CONFIG_NAND)
+#define CONFIG_SYS_EXTRA_ENV_RELOC
+#define CONFIG_ENV_IS_IN_NAND
+#define CONFIG_ENV_SIZE 0x2000
+#define CONFIG_ENV_OFFSET (2 * CONFIG_SYS_NAND_BLOCK_SIZE)
+#elif defined(CONFIG_SRIO_PCIE_BOOT_SLAVE)
+#define CONFIG_ENV_IS_IN_REMOTE
+#define CONFIG_ENV_ADDR 0xffe20000
+#define CONFIG_ENV_SIZE 0x2000
+#elif defined(CONFIG_ENV_IS_NOWHERE)
+#define CONFIG_ENV_SIZE 0x2000
+#else
+#define CONFIG_ENV_IS_IN_FLASH
+#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SECT_SIZE)
+#define CONFIG_ENV_SIZE 0x2000
+#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K (one sector) */
+#endif
+
+
+#ifndef __ASSEMBLY__
+unsigned long get_board_sys_clk(void);
+unsigned long get_board_ddr_clk(void);
+#endif
+
+#define CONFIG_SYS_CLK_FREQ 100000000
+#define CONFIG_DDR_CLK_FREQ 66660000
+
+/*
+ * These can be toggled for performance analysis, otherwise use default.
+ */
+#define CONFIG_SYS_CACHE_STASHING
+#define CONFIG_BACKSIDE_L2_CACHE
+#define CONFIG_SYS_INIT_L2CSR0 L2CSR0_L2E
+#define CONFIG_BTB /* toggle branch predition */
+#define CONFIG_DDR_ECC
+#ifdef CONFIG_DDR_ECC
+#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER
+#define CONFIG_MEM_INIT_VALUE 0xdeadbeef
+#endif
+
+#define CONFIG_SYS_MEMTEST_START 0x00200000 /* memtest works on */
+#define CONFIG_SYS_MEMTEST_END 0x00400000
+#define CONFIG_SYS_ALT_MEMTEST
+#define CONFIG_PANIC_HANG /* do not reset board on panic */
+
+/*
+ * Config the L3 Cache as L3 SRAM
+ */
+#define CONFIG_SYS_INIT_L3_ADDR 0xFFFC0000
+#define CONFIG_SYS_L3_SIZE (256 << 10)
+#define CONFIG_SPL_GD_ADDR (CONFIG_SYS_INIT_L3_ADDR + 32 * 1024)
+#ifdef CONFIG_RAMBOOT_PBL
+#define CONFIG_ENV_ADDR (CONFIG_SPL_GD_ADDR + 4 * 1024)
+#endif
+#define CONFIG_SPL_RELOC_MALLOC_ADDR (CONFIG_SPL_GD_ADDR + 12 * 1024)
+#define CONFIG_SPL_RELOC_MALLOC_SIZE (30 << 10)
+#define CONFIG_SPL_RELOC_STACK (CONFIG_SPL_GD_ADDR + 64 * 1024)
+#define CONFIG_SPL_RELOC_STACK_SIZE (22 << 10)
+
+#ifdef CONFIG_PHYS_64BIT
+#define CONFIG_SYS_DCSRBAR 0xf0000000
+#define CONFIG_SYS_DCSRBAR_PHYS 0xf00000000ull
+#endif
+
+/* EEPROM */
+#define CONFIG_ID_EEPROM
+#define CONFIG_SYS_I2C_EEPROM_NXID
+#define CONFIG_SYS_EEPROM_BUS_NUM 0
+#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50
+#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 5
+
+/*
+ * DDR Setup
+ */
+#define CONFIG_VERY_BIG_RAM
+#define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000
+#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE
+#define CONFIG_DIMM_SLOTS_PER_CTLR 1
+#define CONFIG_CHIP_SELECTS_PER_CTRL (4 * CONFIG_DIMM_SLOTS_PER_CTLR)
+#define CONFIG_DDR_SPD
+#define CONFIG_SYS_FSL_DDR3
+
+#define CONFIG_SYS_SPD_BUS_NUM 0
+#define SPD_EEPROM_ADDRESS 0x51
+
+#define CONFIG_SYS_SDRAM_SIZE 4096 /* for fixed parameter use */
+
+/*
+ * IFC Definitions
+ */
+#define CONFIG_SYS_FLASH_BASE 0xe8000000
+#ifdef CONFIG_PHYS_64BIT
+#define CONFIG_SYS_FLASH_BASE_PHYS (0xf00000000ull | CONFIG_SYS_FLASH_BASE)
+#else
+#define CONFIG_SYS_FLASH_BASE_PHYS CONFIG_SYS_FLASH_BASE
+#endif
+
+#define CONFIG_SYS_NOR0_CSPR_EXT (0xf)
+#define CONFIG_SYS_NOR0_CSPR (CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) | \
+ CSPR_PORT_SIZE_16 | \
+ CSPR_MSEL_NOR | \
+ CSPR_V)
+#define CONFIG_SYS_NOR_AMASK IFC_AMASK(128*1024*1024)
+
+/* NOR Flash Timing Params */
+#define CONFIG_SYS_NOR_CSOR CSOR_NAND_TRHZ_80
+#define CONFIG_SYS_NOR_FTIM0 (FTIM0_NOR_TACSE(0x4) | \
+ FTIM0_NOR_TEADC(0x5) | \
+ FTIM0_NOR_TEAHC(0x5))
+#define CONFIG_SYS_NOR_FTIM1 (FTIM1_NOR_TACO(0x35) | \
+ FTIM1_NOR_TRAD_NOR(0x1A) |\
+ FTIM1_NOR_TSEQRAD_NOR(0x13))
+#define CONFIG_SYS_NOR_FTIM2 (FTIM2_NOR_TCS(0x4) | \
+ FTIM2_NOR_TCH(0x4) | \
+ FTIM2_NOR_TWPH(0x0E) | \
+ FTIM2_NOR_TWP(0x1c))
+#define CONFIG_SYS_NOR_FTIM3 0x0
+
+#define CONFIG_SYS_FLASH_QUIET_TEST
+#define CONFIG_FLASH_SHOW_PROGRESS 45 /* count down from 45/5: 9..1 */
+
+#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */
+#define CONFIG_SYS_MAX_FLASH_SECT 1024 /* sectors per device */
+#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */
+#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */
+
+#define CONFIG_SYS_FLASH_EMPTY_INFO
+#define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE_PHYS}
+
+/* CPLD on IFC */
+#define CONFIG_SYS_CPLD_BASE 0xffdf0000
+#define CONFIG_SYS_CPLD_BASE_PHYS (0xf00000000ull | CONFIG_SYS_CPLD_BASE)
+#define CONFIG_SYS_CSPR2_EXT (0xf)
+#define CONFIG_SYS_CSPR2 (CSPR_PHYS_ADDR(CONFIG_SYS_CPLD_BASE) \
+ | CSPR_PORT_SIZE_8 \
+ | CSPR_MSEL_GPCM \
+ | CSPR_V)
+#define CONFIG_SYS_AMASK2 IFC_AMASK(64*1024)
+#define CONFIG_SYS_CSOR2 0x0
+
+/* CPLD Timing parameters for IFC CS2 */
+#define CONFIG_SYS_CS2_FTIM0 (FTIM0_GPCM_TACSE(0x0e) | \
+ FTIM0_GPCM_TEADC(0x0e) | \
+ FTIM0_GPCM_TEAHC(0x0e))
+#define CONFIG_SYS_CS2_FTIM1 (FTIM1_GPCM_TACO(0x0e) | \
+ FTIM1_GPCM_TRAD(0x1f))
+#define CONFIG_SYS_CS2_FTIM2 (FTIM2_GPCM_TCS(0x0e) | \
+ FTIM2_GPCM_TCH(0x8) | \
+ FTIM2_GPCM_TWP(0x1f))
+#define CONFIG_SYS_CS2_FTIM3 0x0
+
+/* NAND Flash on IFC */
+#define CONFIG_NAND_FSL_IFC
+#define CONFIG_SYS_NAND_BASE 0xff800000
+#ifdef CONFIG_PHYS_64BIT
+#define CONFIG_SYS_NAND_BASE_PHYS (0xf00000000ull | CONFIG_SYS_NAND_BASE)
+#else
+#define CONFIG_SYS_NAND_BASE_PHYS CONFIG_SYS_NAND_BASE
+#endif
+#define CONFIG_SYS_NAND_CSPR_EXT (0xf)
+#define CONFIG_SYS_NAND_CSPR (CSPR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \
+ | CSPR_PORT_SIZE_8 /* Port Size = 8 bit */ \
+ | CSPR_MSEL_NAND /* MSEL = NAND */ \
+ | CSPR_V)
+#define CONFIG_SYS_NAND_AMASK IFC_AMASK(64*1024)
+
+#define CONFIG_SYS_NAND_CSOR (CSOR_NAND_ECC_ENC_EN /* ECC on encode */ \
+ | CSOR_NAND_ECC_DEC_EN /* ECC on decode */ \
+ | CSOR_NAND_ECC_MODE_4 /* 4-bit ECC */ \
+ | CSOR_NAND_RAL_3 /* RAL = 3Byes */ \
+ | CSOR_NAND_PGS_4K /* Page Size = 4K */ \
+ | CSOR_NAND_SPRZ_224 /* Spare size = 224 */ \
+ | CSOR_NAND_PB(64)) /*Pages Per Block = 64*/
+
+#define CONFIG_SYS_NAND_ONFI_DETECTION
+
+/* ONFI NAND Flash mode0 Timing Params */
+#define CONFIG_SYS_NAND_FTIM0 (FTIM0_NAND_TCCST(0x07) | \
+ FTIM0_NAND_TWP(0x18) | \
+ FTIM0_NAND_TWCHT(0x07) | \
+ FTIM0_NAND_TWH(0x0a))
+#define CONFIG_SYS_NAND_FTIM1 (FTIM1_NAND_TADLE(0x32) | \
+ FTIM1_NAND_TWBE(0x39) | \
+ FTIM1_NAND_TRR(0x0e) | \
+ FTIM1_NAND_TRP(0x18))
+#define CONFIG_SYS_NAND_FTIM2 (FTIM2_NAND_TRAD(0x0f) | \
+ FTIM2_NAND_TREH(0x0a) | \
+ FTIM2_NAND_TWHRE(0x1e))
+#define CONFIG_SYS_NAND_FTIM3 0x0
+
+#define CONFIG_SYS_NAND_DDR_LAW 11
+#define CONFIG_SYS_NAND_BASE_LIST { CONFIG_SYS_NAND_BASE }
+#define CONFIG_SYS_MAX_NAND_DEVICE 1
+#define CONFIG_MTD_NAND_VERIFY_WRITE
+#define CONFIG_CMD_NAND
+
+#define CONFIG_SYS_NAND_BLOCK_SIZE (512 * 1024)
+
+#if defined(CONFIG_NAND)
+#define CONFIG_SYS_CSPR0_EXT CONFIG_SYS_NAND_CSPR_EXT
+#define CONFIG_SYS_CSPR0 CONFIG_SYS_NAND_CSPR
+#define CONFIG_SYS_AMASK0 CONFIG_SYS_NAND_AMASK
+#define CONFIG_SYS_CSOR0 CONFIG_SYS_NAND_CSOR
+#define CONFIG_SYS_CS0_FTIM0 CONFIG_SYS_NAND_FTIM0
+#define CONFIG_SYS_CS0_FTIM1 CONFIG_SYS_NAND_FTIM1
+#define CONFIG_SYS_CS0_FTIM2 CONFIG_SYS_NAND_FTIM2
+#define CONFIG_SYS_CS0_FTIM3 CONFIG_SYS_NAND_FTIM3
+#define CONFIG_SYS_CSPR1_EXT CONFIG_SYS_NOR0_CSPR_EXT
+#define CONFIG_SYS_CSPR1 CONFIG_SYS_NOR0_CSPR
+#define CONFIG_SYS_AMASK1 CONFIG_SYS_NOR_AMASK
+#define CONFIG_SYS_CSOR1 CONFIG_SYS_NOR_CSOR
+#define CONFIG_SYS_CS1_FTIM0 CONFIG_SYS_NOR_FTIM0
+#define CONFIG_SYS_CS1_FTIM1 CONFIG_SYS_NOR_FTIM1
+#define CONFIG_SYS_CS1_FTIM2 CONFIG_SYS_NOR_FTIM2
+#define CONFIG_SYS_CS1_FTIM3 CONFIG_SYS_NOR_FTIM3
+#else
+#define CONFIG_SYS_CSPR0_EXT CONFIG_SYS_NOR0_CSPR_EXT
+#define CONFIG_SYS_CSPR0 CONFIG_SYS_NOR0_CSPR
+#define CONFIG_SYS_AMASK0 CONFIG_SYS_NOR_AMASK
+#define CONFIG_SYS_CSOR0 CONFIG_SYS_NOR_CSOR
+#define CONFIG_SYS_CS0_FTIM0 CONFIG_SYS_NOR_FTIM0
+#define CONFIG_SYS_CS0_FTIM1 CONFIG_SYS_NOR_FTIM1
+#define CONFIG_SYS_CS0_FTIM2 CONFIG_SYS_NOR_FTIM2
+#define CONFIG_SYS_CS0_FTIM3 CONFIG_SYS_NOR_FTIM3
+#define CONFIG_SYS_CSPR1_EXT CONFIG_SYS_NAND_CSPR_EXT
+#define CONFIG_SYS_CSPR1 CONFIG_SYS_NAND_CSPR
+#define CONFIG_SYS_AMASK1 CONFIG_SYS_NAND_AMASK
+#define CONFIG_SYS_CSOR1 CONFIG_SYS_NAND_CSOR
+#define CONFIG_SYS_CS1_FTIM0 CONFIG_SYS_NAND_FTIM0
+#define CONFIG_SYS_CS1_FTIM1 CONFIG_SYS_NAND_FTIM1
+#define CONFIG_SYS_CS1_FTIM2 CONFIG_SYS_NAND_FTIM2
+#define CONFIG_SYS_CS1_FTIM3 CONFIG_SYS_NAND_FTIM3
+#endif
+
+#ifdef CONFIG_SPL_BUILD
+#define CONFIG_SYS_MONITOR_BASE CONFIG_SPL_TEXT_BASE
+#else
+#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE
+#endif
+
+#if defined(CONFIG_RAMBOOT_PBL)
+#define CONFIG_SYS_RAMBOOT
+#endif
+
+#define CONFIG_BOARD_EARLY_INIT_R
+#define CONFIG_MISC_INIT_R
+
+#define CONFIG_HWCONFIG
+
+/* define to use L1 as initial stack */
+#define CONFIG_L1_INIT_RAM
+#define CONFIG_SYS_INIT_RAM_LOCK
+#define CONFIG_SYS_INIT_RAM_ADDR 0xfdd00000 /* Initial L1 address */
+#ifdef CONFIG_PHYS_64BIT
+#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0xf
+#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW 0xfe0ec000
+/* The assembler doesn't like typecast */
+#define CONFIG_SYS_INIT_RAM_ADDR_PHYS \
+ ((CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH * 1ull << 32) | \
+ CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW)
+#else
+#define CONFIG_SYS_INIT_RAM_ADDR_PHYS 0xfe0ec000 /* Initial L1 address */
+#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0
+#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW CONFIG_SYS_INIT_RAM_ADDR_PHYS
+#endif
+#define CONFIG_SYS_INIT_RAM_SIZE 0x00004000
+
+#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - \
+ GENERATED_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
+
+#define CONFIG_SYS_MONITOR_LEN (768 * 1024)
+#define CONFIG_SYS_MALLOC_LEN (10 * 1024 * 1024)
+
+/* Serial Port */
+#define CONFIG_CONS_INDEX 1
+#define CONFIG_SYS_NS16550
+#define CONFIG_SYS_NS16550_SERIAL
+#define CONFIG_SYS_NS16550_REG_SIZE 1
+#define CONFIG_SYS_NS16550_CLK (get_bus_freq(0)/2)
+
+#define CONFIG_SYS_BAUDRATE_TABLE \
+ {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
+
+#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x11C500)
+#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x11C600)
+#define CONFIG_SYS_NS16550_COM3 (CONFIG_SYS_CCSRBAR+0x11D500)
+#define CONFIG_SYS_NS16550_COM4 (CONFIG_SYS_CCSRBAR+0x11D600)
+#define CONFIG_SYS_CONSOLE_IS_IN_ENV /* determine from environment */
+
+/* Use the HUSH parser */
+#define CONFIG_SYS_HUSH_PARSER
+#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
+
+/* Video */
+#undef CONFIG_FSL_DIU_FB /* RDB doesn't support DIU */
+#ifdef CONFIG_FSL_DIU_FB
+#define CONFIG_SYS_DIU_ADDR (CONFIG_SYS_CCSRBAR + 0x180000)
+#define CONFIG_VIDEO
+#define CONFIG_CMD_BMP
+#define CONFIG_CFB_CONSOLE
+#define CONFIG_VIDEO_SW_CURSOR
+#define CONFIG_VGA_AS_SINGLE_DEVICE
+#define CONFIG_VIDEO_LOGO
+#define CONFIG_VIDEO_BMP_LOGO
+#define CONFIG_CFI_FLASH_USE_WEAK_ACCESSORS
+/*
+ * With CONFIG_CFI_FLASH_USE_WEAK_ACCESSORS, flash I/O is really slow, so
+ * disable empty flash sector detection, which is I/O-intensive.
+ */
+#undef CONFIG_SYS_FLASH_EMPTY_INFO
+#endif
+
+/* pass open firmware flat tree */
+#define CONFIG_OF_LIBFDT
+#define CONFIG_OF_BOARD_SETUP
+#define CONFIG_OF_STDOUT_VIA_ALIAS
+
+/* new uImage format support */
+#define CONFIG_FIT
+#define CONFIG_FIT_VERBOSE /* enable fit_format_{error,warning}() */
+
+/* I2C */
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_FSL /* Use FSL common I2C driver */
+#define CONFIG_SYS_FSL_I2C_SPEED 50000 /* I2C speed in Hz */
+#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
+#define CONFIG_SYS_FSL_I2C2_SPEED 50000 /* I2C speed in Hz */
+#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F
+#define CONFIG_SYS_FSL_I2C_OFFSET 0x118000
+#define CONFIG_SYS_FSL_I2C2_OFFSET 0x118100
+
+#define I2C_MUX_PCA_ADDR 0x77
+#define I2C_MUX_PCA_ADDR_PRI 0x77 /* Primary Mux*/
+
+
+/* I2C bus multiplexer */
+#define I2C_MUX_CH_DEFAULT 0x8
+
+/*
+ * RTC configuration
+ */
+#define RTC
+#define CONFIG_RTC_DS1337 1
+#define CONFIG_SYS_I2C_RTC_ADDR 0x68
+
+/*
+ * eSPI - Enhanced SPI
+ */
+#define CONFIG_FSL_ESPI
+#define CONFIG_SPI_FLASH
+#define CONFIG_SPI_FLASH_STMICRO
+#define CONFIG_CMD_SF
+#define CONFIG_SPI_FLASH_BAR
+#define CONFIG_SF_DEFAULT_SPEED 10000000
+#define CONFIG_SF_DEFAULT_MODE 0
+
+/*
+ * General PCIe
+ * Memory space is mapped 1-1, but I/O space must start from 0.
+ */
+#define CONFIG_PCI /* Enable PCI/PCIE */
+#define CONFIG_PCIE1 /* PCIE controler 1 */
+#define CONFIG_PCIE2 /* PCIE controler 2 */
+#define CONFIG_PCIE3 /* PCIE controler 3 */
+#ifdef CONFIG_PPC_T1040
+#define CONFIG_PCIE4 /* PCIE controler 4 */
+#endif
+#define CONFIG_FSL_PCI_INIT /* Use common FSL init code */
+#define CONFIG_SYS_PCI_64BIT /* enable 64-bit PCI resources */
+#define CONFIG_PCI_INDIRECT_BRIDGE
+
+#ifdef CONFIG_PCI
+/* controller 1, direct to uli, tgtid 3, Base address 20000 */
+#ifdef CONFIG_PCIE1
+#define CONFIG_SYS_PCIE1_MEM_VIRT 0x80000000
+#ifdef CONFIG_PHYS_64BIT
+#define CONFIG_SYS_PCIE1_MEM_BUS 0xe0000000
+#define CONFIG_SYS_PCIE1_MEM_PHYS 0xc00000000ull
+#else
+#define CONFIG_SYS_PCIE1_MEM_BUS 0x80000000
+#define CONFIG_SYS_PCIE1_MEM_PHYS 0x80000000
+#endif
+#define CONFIG_SYS_PCIE1_MEM_SIZE 0x10000000 /* 256M */
+#define CONFIG_SYS_PCIE1_IO_VIRT 0xf8000000
+#define CONFIG_SYS_PCIE1_IO_BUS 0x00000000
+#ifdef CONFIG_PHYS_64BIT
+#define CONFIG_SYS_PCIE1_IO_PHYS 0xff8000000ull
+#else
+#define CONFIG_SYS_PCIE1_IO_PHYS 0xf8000000
+#endif
+#define CONFIG_SYS_PCIE1_IO_SIZE 0x00010000 /* 64k */
+#endif
+
+/* controller 2, Slot 2, tgtid 2, Base address 201000 */
+#ifdef CONFIG_PCIE2
+#define CONFIG_SYS_PCIE2_MEM_VIRT 0x90000000
+#ifdef CONFIG_PHYS_64BIT
+#define CONFIG_SYS_PCIE2_MEM_BUS 0xe0000000
+#define CONFIG_SYS_PCIE2_MEM_PHYS 0xc10000000ull
+#else
+#define CONFIG_SYS_PCIE2_MEM_BUS 0x90000000
+#define CONFIG_SYS_PCIE2_MEM_PHYS 0x90000000
+#endif
+#define CONFIG_SYS_PCIE2_MEM_SIZE 0x10000000 /* 256M */
+#define CONFIG_SYS_PCIE2_IO_VIRT 0xf8010000
+#define CONFIG_SYS_PCIE2_IO_BUS 0x00000000
+#ifdef CONFIG_PHYS_64BIT
+#define CONFIG_SYS_PCIE2_IO_PHYS 0xff8010000ull
+#else
+#define CONFIG_SYS_PCIE2_IO_PHYS 0xf8010000
+#endif
+#define CONFIG_SYS_PCIE2_IO_SIZE 0x00010000 /* 64k */
+#endif
+
+/* controller 3, Slot 1, tgtid 1, Base address 202000 */
+#ifdef CONFIG_PCIE3
+#define CONFIG_SYS_PCIE3_MEM_VIRT 0xa0000000
+#ifdef CONFIG_PHYS_64BIT
+#define CONFIG_SYS_PCIE3_MEM_BUS 0xe0000000
+#define CONFIG_SYS_PCIE3_MEM_PHYS 0xc20000000ull
+#else
+#define CONFIG_SYS_PCIE3_MEM_BUS 0xa0000000
+#define CONFIG_SYS_PCIE3_MEM_PHYS 0xa0000000
+#endif
+#define CONFIG_SYS_PCIE3_MEM_SIZE 0x10000000 /* 256M */
+#define CONFIG_SYS_PCIE3_IO_VIRT 0xf8020000
+#define CONFIG_SYS_PCIE3_IO_BUS 0x00000000
+#ifdef CONFIG_PHYS_64BIT
+#define CONFIG_SYS_PCIE3_IO_PHYS 0xff8020000ull
+#else
+#define CONFIG_SYS_PCIE3_IO_PHYS 0xf8020000
+#endif
+#define CONFIG_SYS_PCIE3_IO_SIZE 0x00010000 /* 64k */
+#endif
+
+/* controller 4, Base address 203000, to be removed */
+#ifdef CONFIG_PCIE4
+#define CONFIG_SYS_PCIE4_MEM_VIRT 0xb0000000
+#ifdef CONFIG_PHYS_64BIT
+#define CONFIG_SYS_PCIE4_MEM_BUS 0xe0000000
+#define CONFIG_SYS_PCIE4_MEM_PHYS 0xc30000000ull
+#else
+#define CONFIG_SYS_PCIE4_MEM_BUS 0xb0000000
+#define CONFIG_SYS_PCIE4_MEM_PHYS 0xb0000000
+#endif
+#define CONFIG_SYS_PCIE4_MEM_SIZE 0x10000000 /* 256M */
+#define CONFIG_SYS_PCIE4_IO_VIRT 0xf8030000
+#define CONFIG_SYS_PCIE4_IO_BUS 0x00000000
+#ifdef CONFIG_PHYS_64BIT
+#define CONFIG_SYS_PCIE4_IO_PHYS 0xff8030000ull
+#else
+#define CONFIG_SYS_PCIE4_IO_PHYS 0xf8030000
+#endif
+#define CONFIG_SYS_PCIE4_IO_SIZE 0x00010000 /* 64k */
+#endif
+
+#define CONFIG_PCI_PNP /* do pci plug-and-play */
+#define CONFIG_E1000
+#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
+#define CONFIG_DOS_PARTITION
+#endif /* CONFIG_PCI */
+
+/*
+ * USB
+ */
+#define CONFIG_HAS_FSL_DR_USB
+
+#ifdef CONFIG_HAS_FSL_DR_USB
+#define CONFIG_USB_EHCI
+#define CONFIG_CMD_USB
+#define CONFIG_USB_STORAGE
+#define CONFIG_USB_EHCI_FSL
+#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
+#define CONFIG_CMD_EXT2
+#endif
+
+/*
+ * SDHC
+ */
+#define CONFIG_MMC
+#ifdef CONFIG_MMC
+#define CONFIG_FSL_ESDHC
+#define CONFIG_SYS_FSL_ESDHC_ADDR CONFIG_SYS_MPC85xx_ESDHC_ADDR
+#define CONFIG_CMD_MMC
+#define CONFIG_GENERIC_MMC
+#define CONFIG_CMD_EXT2
+#define CONFIG_CMD_FAT
+#define CONFIG_DOS_PARTITION
+#endif
+
+/* Qman/Bman */
+#ifndef CONFIG_NOBQFMAN
+#define CONFIG_SYS_DPAA_QBMAN /* Support Q/Bman */
+#define CONFIG_SYS_BMAN_NUM_PORTALS 25
+#define CONFIG_SYS_BMAN_MEM_BASE 0xf4000000
+#ifdef CONFIG_PHYS_64BIT
+#define CONFIG_SYS_BMAN_MEM_PHYS 0xff4000000ull
+#else
+#define CONFIG_SYS_BMAN_MEM_PHYS CONFIG_SYS_BMAN_MEM_BASE
+#endif
+#define CONFIG_SYS_BMAN_MEM_SIZE 0x02000000
+#define CONFIG_SYS_QMAN_NUM_PORTALS 25
+#define CONFIG_SYS_QMAN_MEM_BASE 0xf6000000
+#ifdef CONFIG_PHYS_64BIT
+#define CONFIG_SYS_QMAN_MEM_PHYS 0xff6000000ull
+#else
+#define CONFIG_SYS_QMAN_MEM_PHYS CONFIG_SYS_QMAN_MEM_BASE
+#endif
+#define CONFIG_SYS_QMAN_MEM_SIZE 0x02000000
+
+#define CONFIG_SYS_DPAA_FMAN
+
+#define CONFIG_QE
+#define CONFIG_U_QE
+/* Default address of microcode for the Linux FMan driver */
+#if defined(CONFIG_SPIFLASH)
+/*
+ * env is stored at 0x100000, sector size is 0x10000, ucode is stored after
+ * env, so we got 0x110000.
+ */
+#define CONFIG_SYS_QE_FW_IN_SPIFLASH
+#define CONFIG_SYS_FMAN_FW_ADDR 0x110000
+#define CONFIG_SYS_QE_FW_ADDR 0x130000
+#elif defined(CONFIG_SDCARD)
+/*
+ * PBL SD boot image should stored at 0x1000(8 blocks), the size of the image is
+ * about 1MB (2048 blocks), Env is stored after the image, and the env size is
+ * 0x2000 (16 blocks), 8 + 2048 + 16 = 2072, enlarge it to 2080(0x820).
+ */
+#define CONFIG_SYS_QE_FMAN_FW_IN_MMC
+#define CONFIG_SYS_FMAN_FW_ADDR (512 * 0x820)
+#define CONFIG_SYS_QE_FW_ADDR (512 * 0x920)
+#elif defined(CONFIG_NAND)
+#define CONFIG_SYS_QE_FMAN_FW_IN_NAND
+#define CONFIG_SYS_FMAN_FW_ADDR (3 * CONFIG_SYS_NAND_BLOCK_SIZE)
+#define CONFIG_SYS_QE_FW_ADDR (4 * CONFIG_SYS_NAND_BLOCK_SIZE)
+#elif defined(CONFIG_SRIO_PCIE_BOOT_SLAVE)
+/*
+ * Slave has no ucode locally, it can fetch this from remote. When implementing
+ * in two corenet boards, slave's ucode could be stored in master's memory
+ * space, the address can be mapped from slave TLB->slave LAW->
+ * slave SRIO or PCIE outbound window->master inbound window->
+ * master LAW->the ucode address in master's memory space.
+ */
+#define CONFIG_SYS_QE_FMAN_FW_IN_REMOTE
+#define CONFIG_SYS_FMAN_FW_ADDR 0xFFE00000
+#else
+#define CONFIG_SYS_QE_FMAN_FW_IN_NOR
+#define CONFIG_SYS_FMAN_FW_ADDR 0xEFF00000
+#define CONFIG_SYS_QE_FW_ADDR 0xEFE00000
+#endif
+#define CONFIG_SYS_QE_FMAN_FW_LENGTH 0x10000
+#define CONFIG_SYS_FDT_PAD (0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH)
+#endif /* CONFIG_NOBQFMAN */
+
+#ifdef CONFIG_SYS_DPAA_FMAN
+#define CONFIG_FMAN_ENET
+#define CONFIG_PHYLIB_10G
+#define CONFIG_PHY_REALTEK
+#define RGMII_PHY1_ADDR 0x2
+#define RGMII_PHY2_ADDR 0x6
+#define FM1_10GEC1_PHY_ADDR 0x1
+#endif
+
+#ifdef CONFIG_FMAN_ENET
+#define CONFIG_MII /* MII PHY management */
+#define CONFIG_ETHPRIME "FM1@DTSEC4"
+#define CONFIG_PHY_GIGE /* Include GbE speed/duplex detection */
+#endif
+
+/*
+ * Dynamic MTD Partition support with mtdparts
+ */
+#ifndef CONFIG_SYS_NO_FLASH
+#define CONFIG_MTD_DEVICE
+#define CONFIG_MTD_PARTITIONS
+#define CONFIG_CMD_MTDPARTS
+#define CONFIG_FLASH_CFI_MTD
+#define MTDIDS_DEFAULT "nor0=fe8000000.nor,nand0=fff800000.flash," \
+ "spi0=spife110000.1"
+#define MTDPARTS_DEFAULT "mtdparts=fe8000000.nor:1m(uboot),5m(kernel)," \
+ "128k(dtb),96m(fs),-(user);fff800000.flash:1m(uboot)," \
+ "5m(kernel),128k(dtb),96m(fs),-(user);spife110000.0:" \
+ "1m(uboot),5m(kernel),128k(dtb),-(user)"
+#endif
+
+/*
+ * Environment
+ */
+#define CONFIG_LOADS_ECHO /* echo on for serial download */
+#define CONFIG_SYS_LOADS_BAUD_CHANGE /* allow baudrate change */
+
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_DATE
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_EEPROM
+#define CONFIG_CMD_ELF
+#define CONFIG_CMD_ERRATA
+#define CONFIG_CMD_GREPENV
+#define CONFIG_CMD_IRQ
+#define CONFIG_CMD_I2C
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_ECHO
+#define CONFIG_CMD_REGINFO
+#define CONFIG_CMD_SETEXPR
+#define CONFIG_CMD_BDI
+
+#ifdef CONFIG_PCI
+#define CONFIG_CMD_PCI
+#define CONFIG_CMD_NET
+#endif
+
+/*
+ * Miscellaneous configurable options
+ */
+#define CONFIG_SYS_LONGHELP /* undef to save memory */
+#define CONFIG_CMDLINE_EDITING /* Command-line editing */
+#define CONFIG_AUTO_COMPLETE /* add autocompletion support */
+#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */
+#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */
+#ifdef CONFIG_CMD_KGDB
+#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
+#else
+#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
+#endif
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16)
+#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
+#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 64 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CONFIG_SYS_BOOTMAPSZ (64 << 20) /* Initial map for Linux*/
+#define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */
+
+#ifdef CONFIG_CMD_KGDB
+#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
+#endif
+
+/*
+ * Environment Configuration
+ */
+#define CONFIG_ROOTPATH "/opt/nfsroot"
+#define CONFIG_BOOTFILE "uImage"
+#define CONFIG_UBOOTPATH "u-boot.bin" /* U-Boot image on TFTP server */
+#define CONFIG_LOADADDR 1000000 /* default location for tftp, bootm */
+#define CONFIG_BOOTDELAY 10 /* -1 disables auto-boot */
+#define CONFIG_BAUDRATE 115200
+#define __USB_PHY_TYPE utmi
+
+#ifdef CONFIG_PPC_T1024
+#define CONFIG_BOARDNAME "t1024rdb"
+#else
+#define CONFIG_BOARDNAME "t1023rdb"
+#endif
+
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ "hwconfig=fsl_ddr:ctlr_intlv=cacheline," \
+ "bank_intlv=cs0_cs1\0" \
+ "usb1:dr_mode=host,phy_type=" __stringify(__USB_PHY_TYPE) "\0" \
+ "ramdiskfile=" __stringify(CONFIG_BOARDNAME) "/ramdisk.uboot\0" \
+ "fdtfile=" __stringify(CONFIG_BOARDNAME) "/" \
+ __stringify(CONFIG_BOARDNAME) ".dtb\0" \
+ "uboot=" __stringify(CONFIG_UBOOTPATH) "\0" \
+ "ubootaddr=" __stringify(CONFIG_SYS_TEXT_BASE) "\0" \
+ "bootargs=root=/dev/ram rw console=ttyS0,115200\0" \
+ "netdev=eth0\0" \
+ "tftpflash=tftpboot $loadaddr $uboot && " \
+ "protect off $ubootaddr +$filesize && " \
+ "erase $ubootaddr +$filesize && " \
+ "cp.b $loadaddr $ubootaddr $filesize && " \
+ "protect on $ubootaddr +$filesize && " \
+ "cmp.b $loadaddr $ubootaddr $filesize\0" \
+ "consoledev=ttyS0\0" \
+ "ramdiskaddr=2000000\0" \
+ "fdtaddr=c00000\0" \
+ "bdev=sda3\0"
+
+#define CONFIG_LINUX \
+ "setenv bootargs root=/dev/ram rw " \
+ "console=$consoledev,$baudrate $othbootargs;" \
+ "setenv ramdiskaddr 0x02000000;" \
+ "setenv fdtaddr 0x00c00000;" \
+ "setenv loadaddr 0x1000000;" \
+ "bootm $loadaddr $ramdiskaddr $fdtaddr"
+
+
+#define CONFIG_NFSBOOTCOMMAND \
+ "setenv bootargs root=/dev/nfs rw " \
+ "nfsroot=$serverip:$rootpath " \
+ "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
+ "console=$consoledev,$baudrate $othbootargs;" \
+ "tftp $loadaddr $bootfile;" \
+ "tftp $fdtaddr $fdtfile;" \
+ "bootm $loadaddr - $fdtaddr"
+
+#define CONFIG_BOOTCOMMAND CONFIG_LINUX
+
+#ifdef CONFIG_SECURE_BOOT
+#include <asm/fsl_secure_boot.h>
+#endif
+
+#endif /* __T1024RDB_H */
diff --git a/include/configs/T1040QDS.h b/include/configs/T1040QDS.h
index 2178f9d..6b396bb 100644
--- a/include/configs/T1040QDS.h
+++ b/include/configs/T1040QDS.h
@@ -28,6 +28,8 @@
*/
#define CONFIG_T1040QDS
#define CONFIG_PHYS_64BIT
+#define CONFIG_SYS_GENERIC_BOARD
+#define CONFIG_DISPLAY_BOARDINFO
#ifdef CONFIG_RAMBOOT_PBL
#define CONFIG_RAMBOOT_TEXT_BASE CONFIG_SYS_TEXT_BASE
@@ -176,8 +178,8 @@
#define CONFIG_DDR_SPD
#ifndef CONFIG_SYS_FSL_DDR4
#define CONFIG_SYS_FSL_DDR3
-#define CONFIG_FSL_DDR_INTERACTIVE
#endif
+#define CONFIG_FSL_DDR_INTERACTIVE
#define CONFIG_SYS_SPD_BUS_NUM 0
#define SPD_EEPROM_ADDRESS 0x51
@@ -768,8 +770,7 @@
#define __USB_PHY_TYPE utmi
#define CONFIG_EXTRA_ENV_SETTINGS \
- "hwconfig=fsl_ddr:ctlr_intlv=cacheline," \
- "bank_intlv=cs0_cs1;" \
+ "hwconfig=fsl_ddr:bank_intlv=auto;" \
"usb1:dr_mode=host,phy_type=" __stringify(__USB_PHY_TYPE) "\0"\
"netdev=eth0\0" \
"video-mode=fslfb:1024x768-32@60,monitor=dvi\0" \
diff --git a/include/configs/T104xRDB.h b/include/configs/T104xRDB.h
index 216f34f..1eb1371 100644
--- a/include/configs/T104xRDB.h
+++ b/include/configs/T104xRDB.h
@@ -12,6 +12,11 @@
*/
#define CONFIG_T104xRDB
#define CONFIG_PHYS_64BIT
+#define CONFIG_SYS_GENERIC_BOARD
+#define CONFIG_DISPLAY_BOARDINFO
+
+#define CONFIG_E500 /* BOOKE e500 family */
+#include <asm/config_mpc85xx.h>
#ifdef CONFIG_RAMBOOT_PBL
#define CONFIG_SYS_FSL_PBL_PBI $(SRCTREE)/board/freescale/t104xrdb/t104x_pbi.cfg
@@ -93,7 +98,6 @@
/* High Level Configuration Options */
#define CONFIG_BOOKE
-#define CONFIG_E500 /* BOOKE e500 family */
#define CONFIG_E500MC /* BOOKE e500mc family */
#define CONFIG_SYS_BOOK3E_HV /* Category E.HV supported */
#define CONFIG_MP /* support multiple processors */
@@ -386,6 +390,12 @@
#define CONFIG_SYS_RAMBOOT
#endif
+#ifdef CONFIG_SYS_FSL_ERRATUM_A008044
+#if defined(CONFIG_NAND)
+#define CONFIG_A008044_WORKAROUND
+#endif
+#endif
+
#define CONFIG_BOARD_EARLY_INIT_R
#define CONFIG_MISC_INIT_R
diff --git a/include/configs/T208xQDS.h b/include/configs/T208xQDS.h
index 2f381e7..d1fe78e 100644
--- a/include/configs/T208xQDS.h
+++ b/include/configs/T208xQDS.h
@@ -234,7 +234,7 @@
#define CONFIG_FSL_DDR_FIRST_SLOT_QUAD_CAPABLE
#define CONFIG_DDR_SPD
#define CONFIG_SYS_FSL_DDR3
-#undef CONFIG_FSL_DDR_INTERACTIVE
+#define CONFIG_FSL_DDR_INTERACTIVE
#define CONFIG_SYS_SPD_BUS_NUM 0
#define CONFIG_SYS_SDRAM_SIZE 2048 /* for fixed parameter use */
#define SPD_EEPROM_ADDRESS1 0x51
@@ -494,6 +494,23 @@
#define I2C_MUX_PCA_ADDR_SEC2 0x76 /* I2C bus multiplexer,secondary 2 */
#define I2C_MUX_CH_DEFAULT 0x8
+#define I2C_MUX_CH_VOL_MONITOR 0xa
+
+/* Voltage monitor on channel 2*/
+#define I2C_VOL_MONITOR_ADDR 0x40
+#define I2C_VOL_MONITOR_BUS_V_OFFSET 0x2
+#define I2C_VOL_MONITOR_BUS_V_OVF 0x1
+#define I2C_VOL_MONITOR_BUS_V_SHIFT 3
+
+#define CONFIG_VID_FLS_ENV "t208xqds_vdd_mv"
+#ifndef CONFIG_SPL_BUILD
+#define CONFIG_VID
+#endif
+#define CONFIG_VOL_MONITOR_IR36021_SET
+#define CONFIG_VOL_MONITOR_IR36021_READ
+/* The lowest and highest voltage allowed for T208xQDS */
+#define VDD_MV_MIN 819
+#define VDD_MV_MAX 1212
/*
* RapidIO
diff --git a/include/configs/T4240RDB.h b/include/configs/T4240RDB.h
index 48b8dc7..db03993 100644
--- a/include/configs/T4240RDB.h
+++ b/include/configs/T4240RDB.h
@@ -690,6 +690,7 @@
#define CONFIG_CMD_EXT2
#define CONFIG_CMD_FAT
#define CONFIG_DOS_PARTITION
+#define CONFIG_SYS_FSL_MMC_HAS_CAPBLT_VS33
#endif
/* Hash command with SHA acceleration supported in hardware */
diff --git a/include/configs/km82xx.h b/include/configs/km82xx.h
index 69ba66a..14fd290 100644
--- a/include/configs/km82xx.h
+++ b/include/configs/km82xx.h
@@ -207,9 +207,6 @@
""
#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE
-#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
-#define CONFIG_SYS_RAMBOOT
-#endif
#define CONFIG_SYS_MONITOR_LEN (768 << 10)
diff --git a/include/configs/muas3001.h b/include/configs/muas3001.h
index 7343c94..df2ecc1 100644
--- a/include/configs/muas3001.h
+++ b/include/configs/muas3001.h
@@ -206,10 +206,6 @@
#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE }
#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE
-#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
-#define CONFIG_SYS_RAMBOOT
-#endif
-
#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256KB for Monitor */
#define CONFIG_ENV_IS_IN_FLASH
diff --git a/include/configs/p1_twr.h b/include/configs/p1_twr.h
index 681bc92..9864c15 100644
--- a/include/configs/p1_twr.h
+++ b/include/configs/p1_twr.h
@@ -10,6 +10,8 @@
#ifndef __CONFIG_H
#define __CONFIG_H
+#define CONFIG_SYS_GENERIC_BOARD
+#define CONFIG_DISPLAY_BOARDINFO
#if defined(CONFIG_TWR_P1025)
#define CONFIG_BOARDNAME "TWR-P1025"
#define CONFIG_P1025
diff --git a/include/cortina.h b/include/cortina.h
new file mode 100644
index 0000000..6cadd28
--- /dev/null
+++ b/include/cortina.h
@@ -0,0 +1,75 @@
+/*
+ * Cortina PHY drivers
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ *
+ * Copyright 2014 Freescale Semiconductor, Inc.
+ */
+
+#ifndef _CORTINA_H_
+#define _CORTINA_H_
+
+#define VILLA_GLOBAL_CHIP_ID_LSB 0x000
+#define VILLA_GLOBAL_CHIP_ID_MSB 0x001
+#define VILLA_GLOBAL_BIST_CONTROL 0x002
+#define VILLA_GLOBAL_BIST_STATUS 0x003
+#define VILLA_GLOBAL_LINE_SOFT_RESET 0x007
+#define VILLA_GLOBAL_HOST_SOFT_RESET 0x008
+#define VILLA_GLOBAL_DWNLD_CHECKSUM_CTRL 0x00A
+#define VILLA_GLOBAL_DWNLD_CHECKSUM_STATUS 0x00B
+#define VILLA_GLOBAL_MSEQCLKCTRL 0x00E
+#define VILLA_MSEQ_OPTIONS 0x1D0
+#define VILLA_MSEQ_PC 0x1D3
+#define VILLA_MSEQ_BANKSELECT 0x1DF
+#define VILLA_DSP_SDS_DSP_COEF_DFE0_SELECT 0x2DB
+#define VILLA_DSP_SDS_SERDES_SRX_DFE0_SELECT 0x36E
+#define VILLA_LINE_SDS_COMMON_SRX0_RX_LOOP_FILTER 0x403
+#define VILLA_LINE_SDS_COMMON_SRX0_RX_CPA 0x404
+#define VILLA_LINE_SDS_COMMON_SRX0_RX_CPB 0x405
+#define VILLA_DSP_SDS_SERDES_SRX_FFE_DELAY_CTRL 0x369
+#define VILLA_MSEQ_ENABLE_MSB 0x194
+#define VILLA_MSEQ_SPARE21_LSB 0x226
+#define VILLA_MSEQ_RESET_COUNT_LSB 0x1E0
+#define VILLA_MSEQ_SPARE12_MSB 0x215
+#define VILLA_MSEQ_SPARE2_LSB 0x200
+#define VILLA_MSEQ_SPARE7_LSB 0x20A
+#define VILLA_MSEQ_SPARE9_LSB 0x20E
+#define VILLA_MSEQ_SPARE3_LSB 0x202
+#define VILLA_MSEQ_SPARE3_MSB 0x203
+#define VILLA_MSEQ_SPARE8_LSB 0x20C
+#define VILLA_MSEQ_SPARE8_MSB 0x20D
+#define VILLA_MSEQ_COEF8_FFE0_LSB 0x1E2
+#define VILLA_MSEQ_COEF8_FFE1_LSB 0x1E4
+#define VILLA_MSEQ_COEF8_FFE2_LSB 0x1E6
+#define VILLA_MSEQ_COEF8_FFE3_LSB 0x1E8
+#define VILLA_MSEQ_COEF8_FFE4_LSB 0x1EA
+#define VILLA_MSEQ_COEF8_FFE5_LSB 0x1EC
+#define VILLA_MSEQ_COEF8_DFE0_LSB 0x1F0
+#define VILLA_MSEQ_COEF8_DFE0N_LSB 0x1EE
+#define VILLA_MSEQ_COEF8_DFE1_LSB 0x1F2
+#define VILLA_DSP_SDS_DSP_COEF_LARGE_LEAK 0x2E2
+#define VILLA_DSP_SDS_SERDES_SRX_DAC_ENABLEB_LSB 0x360
+#define VILLA_MSEQ_POWER_DOWN_LSB 0x198
+#define VILLA_MSEQ_POWER_DOWN_MSB 0x199
+#define VILLA_MSEQ_CAL_RX_SLICER 0x1B8
+#define VILLA_DSP_SDS_SERDES_SRX_DAC_BIAS_SELECT1_MSB 0x365
+#define VILLA_MSEQ_COEF_INIT_SEL 0x1AE
+#define VILLA_DSP_SDS_DSP_PRECODEDINITFFE21 0x26A
+#define VILLA_MSEQ_SERDES_PARAM_LSB 0x195
+#define VILLA_MSEQ_SPARE25_LSB 0x22E
+#define VILLA_MSEQ_SPARE23_LSB 0x22A
+#define VILLA_MSEQ_CAL_RX_DFE_EQ 0x1BA
+#define VILLA_GLOBAL_VILLA2_COMPATIBLE 0x030
+#define VILLA_HOST_SDS_COMMON_STX0_TX_OUTPUT_CTRLA 0x812
+#define VILLA_HOST_SDS_COMMON_STX0_TX_OUTPUT_CTRLB 0x813
+#define VILLA_LINE_SDS_COMMON_STX0_TX_OUTPUT_CTRLA 0x427
+#define VILLA_LINE_SDS_COMMON_STX0_TX_OUTPUT_CTRLB 0x428
+
+#define mseq_edc_bist_done (0x1<<0)
+#define mseq_edc_bist_fail (0x1<<8)
+
+struct cortina_reg_config {
+ unsigned short reg_addr;
+ unsigned short reg_value;
+};
+#endif
diff --git a/include/fm_eth.h b/include/fm_eth.h
index e46a684..3e1b9f4 100644
--- a/include/fm_eth.h
+++ b/include/fm_eth.h
@@ -75,6 +75,20 @@
offsetof(struct ccsr_fman, memac[n-1]),\
}
+#ifdef CONFIG_FSL_FM_10GEC_REGULAR_NOTATION
+#define FM_TGEC_INFO_INITIALIZER(idx, n) \
+{ \
+ FM_ETH_INFO_INITIALIZER(idx, CONFIG_SYS_FM1_TGEC_MDIO_ADDR) \
+ .index = idx, \
+ .num = n - 1, \
+ .type = FM_ETH_10G_E, \
+ .port = FM##idx##_10GEC##n, \
+ .rx_port_id = RX_PORT_10G_BASE2 + n - 1, \
+ .tx_port_id = TX_PORT_10G_BASE2 + n - 1, \
+ .compat_offset = CONFIG_SYS_FSL_FM##idx##_OFFSET + \
+ offsetof(struct ccsr_fman, memac[n-1]),\
+}
+#else
#define FM_TGEC_INFO_INITIALIZER(idx, n) \
{ \
FM_ETH_INFO_INITIALIZER(idx, CONFIG_SYS_FM2_TGEC_MDIO_ADDR) \
@@ -87,6 +101,7 @@
.compat_offset = CONFIG_SYS_FSL_FM##idx##_OFFSET + \
offsetof(struct ccsr_fman, memac[n-1+8]),\
}
+#endif
#if (CONFIG_SYS_NUM_FM1_10GEC >= 3)
#define FM_TGEC_INFO_INITIALIZER2(idx, n) \
diff --git a/include/phy.h b/include/phy.h
index d430ed0..1e282e2 100644
--- a/include/phy.h
+++ b/include/phy.h
@@ -227,6 +227,7 @@
int phy_atheros_init(void);
int phy_broadcom_init(void);
+int phy_cortina_init(void);
int phy_davicom_init(void);
int phy_et1011c_init(void);
int phy_lxt_init(void);
@@ -241,6 +242,7 @@
int board_phy_config(struct phy_device *phydev);
/* PHY UIDs for various PHYs that are referenced in external code */
+#define PHY_UID_CS4340 0x13e51002
#define PHY_UID_TN2020 0x00a19410
#endif