board: Add support for Conclusive KSTR-SAMA5D27
Introduce support for Conclusive KSTR-SAMA5D27 Single Board Computer.
Co-developed-by: Jakub Klama <jakub@conclusive.pl>
Signed-off-by: Jakub Klama <jakub@conclusive.pl>
Co-developed-by: Marcin Jabrzyk <marcin@conclusive.pl>
Signed-off-by: Marcin Jabrzyk <marcin@conclusive.pl>
Signed-off-by: Artur Rojek <artur@conclusive.pl>
diff --git a/board/conclusive/kstr-sama5d27/kstr-sama5d27.c b/board/conclusive/kstr-sama5d27/kstr-sama5d27.c
new file mode 100644
index 0000000..1b765b1
--- /dev/null
+++ b/board/conclusive/kstr-sama5d27/kstr-sama5d27.c
@@ -0,0 +1,239 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * kstr-sama5d27.c - Board init file for Conclusive KSTR-SAMA5D27 board
+ * Copyright (C) 2021-2023 Conclusive Engineering Sp. z o. o.
+ */
+
+#include <common.h>
+#include <debug_uart.h>
+#include <init.h>
+#include <env.h>
+#include <fdt_support.h>
+#include <asm/global_data.h>
+#include <asm/io.h>
+#include <asm/arch/at91_common.h>
+#include <asm/arch/atmel_pio4.h>
+#include <asm/arch/atmel_mpddrc.h>
+#include <asm/arch/atmel_sdhci.h>
+#include <asm/arch/clk.h>
+#include <asm/arch/gpio.h>
+#include <asm/arch/sama5d2.h>
+#include <linux/delay.h>
+
+#ifdef CONFIG_USB_GADGET_ATMEL_USBA
+#include <asm/arch/atmel_usba_udc.h>
+#endif
+
+DECLARE_GLOBAL_DATA_PTR;
+
+#ifdef CONFIG_DEBUG_UART_BOARD_INIT
+static void board_uart1_hw_init(void)
+{
+ /* URXD1 */
+ atmel_pio4_set_a_periph(AT91_PIO_PORTD, 2, ATMEL_PIO_PUEN_MASK);
+ /* UTXD1 */
+ atmel_pio4_set_a_periph(AT91_PIO_PORTD, 3, 0);
+ at91_periph_clk_enable(ATMEL_ID_UART1);
+}
+
+void board_debug_uart_init(void)
+{
+ board_uart1_hw_init();
+}
+#endif
+
+void board_lan8720a_init(void)
+{
+ /* LAN8720A_nRST */
+ atmel_pio4_set_pio_output(AT91_PIO_PORTB, 12, 0);
+ /*
+ * Force 0 on RXER/PHYAD0. LAN8720A chipset will latch with address 0 on
+ * MDIO bus.
+ */
+ atmel_pio4_set_pio_output(AT91_PIO_PORTB, 17, 0);
+ /* Minimal delay of reset signal is 25 ms */
+ mdelay(30);
+ /* LAN8720A_nRST */
+ atmel_pio4_set_pio_output(AT91_PIO_PORTB, 12, 1);
+}
+
+void board_usba_init(void)
+{
+#ifdef CONFIG_USB_GADGET_ATMEL_USBA
+ /* USB device peripheral initialization: sama5d2_devices.c */
+ at91_udp_hw_init();
+ /* USB device controller drivers/usb/gadget/atmel_usba_udc.c */
+ usba_udc_probe(&pdata);
+#endif
+}
+
+#ifdef CONFIG_BOARD_EARLY_INIT_F
+int board_early_init_f(void)
+{
+#ifdef CONFIG_DEBUG_UART
+ debug_uart_init();
+#endif
+
+ return 0;
+}
+#endif
+
+int ft_board_setup(void *blob, struct bd_info *bd)
+{
+ char *wlanaddr = env_get("eth1addr");
+
+ if (wlanaddr)
+ do_fixup_by_compat(blob, "brcm,bcm4329-fmac", "local-mac-address",
+ wlanaddr, strlen(wlanaddr), 1);
+ else
+ printf("Not setting WIFI mac address. Check if EEPROM TLV is correctly set up.\n");
+
+ return 0;
+}
+
+int board_init(void)
+{
+ /* address of boot parameters */
+ gd->bd->bi_boot_params = CFG_SYS_SDRAM_BASE + 0x100;
+
+ board_usba_init();
+ board_lan8720a_init();
+
+ return 0;
+}
+
+static int settings_r(void)
+{
+ mac_read_from_eeprom();
+ serial_read_from_eeprom(0);
+
+ return 0;
+}
+EVENT_SPY_SIMPLE(EVT_SETTINGS_R, settings_r);
+
+#if defined(CONFIG_DISPLAY_BOARDINFO_LATE)
+int checkboard(void)
+{
+ const char *serial_number;
+
+ serial_number = env_get("serial#");
+ if (!serial_number)
+ printf("Warning: unknown serial number.\n");
+ else
+ printf("S/N: %s\n", serial_number);
+
+ return 0;
+}
+#endif
+
+#ifdef CONFIG_MISC_INIT_R
+int misc_init_r(void)
+{
+ return 0;
+}
+#endif
+
+int dram_init(void)
+{
+ gd->ram_size = get_ram_size((void *)CFG_SYS_SDRAM_BASE,
+ CFG_SYS_SDRAM_SIZE);
+ return 0;
+}
+
+/* SPL */
+#ifdef CONFIG_SPL_BUILD
+void spl_board_init(void)
+{
+}
+
+static void ddrc_conf(struct atmel_mpddrc_config *ddrc)
+{
+ ddrc->md = (ATMEL_MPDDRC_MD_DBW_16_BITS | ATMEL_MPDDRC_MD_DDR2_SDRAM);
+
+ ddrc->cr = (ATMEL_MPDDRC_CR_NC_COL_10 |
+ ATMEL_MPDDRC_CR_NR_ROW_13 |
+ ATMEL_MPDDRC_CR_CAS_DDR_CAS3 |
+ ATMEL_MPDDRC_CR_DIC_DS |
+ ATMEL_MPDDRC_CR_ZQ_LONG |
+ ATMEL_MPDDRC_CR_NB_8BANKS |
+ ATMEL_MPDDRC_CR_DECOD_INTERLEAVED |
+ ATMEL_MPDDRC_CR_UNAL_SUPPORTED);
+
+ ddrc->rtr = 0x511;
+
+ ddrc->tpr0 = ((7 << ATMEL_MPDDRC_TPR0_TRAS_OFFSET) |
+ (3 << ATMEL_MPDDRC_TPR0_TRCD_OFFSET) |
+ (3 << ATMEL_MPDDRC_TPR0_TWR_OFFSET) |
+ (9 << ATMEL_MPDDRC_TPR0_TRC_OFFSET) |
+ (3 << ATMEL_MPDDRC_TPR0_TRP_OFFSET) |
+ (4 << ATMEL_MPDDRC_TPR0_TRRD_OFFSET) |
+ (4 << ATMEL_MPDDRC_TPR0_TWTR_OFFSET) |
+ (2 << ATMEL_MPDDRC_TPR0_TMRD_OFFSET));
+
+ ddrc->tpr1 = ((22 << ATMEL_MPDDRC_TPR1_TRFC_OFFSET) |
+ (23 << ATMEL_MPDDRC_TPR1_TXSNR_OFFSET) |
+ (200 << ATMEL_MPDDRC_TPR1_TXSRD_OFFSET) |
+ (3 << ATMEL_MPDDRC_TPR1_TXP_OFFSET));
+
+ ddrc->tpr2 = ((2 << ATMEL_MPDDRC_TPR2_TXARD_OFFSET) |
+ (8 << ATMEL_MPDDRC_TPR2_TXARDS_OFFSET) |
+ (4 << ATMEL_MPDDRC_TPR2_TRPA_OFFSET) |
+ (4 << ATMEL_MPDDRC_TPR2_TRTP_OFFSET) |
+ (8 << ATMEL_MPDDRC_TPR2_TFAW_OFFSET));
+}
+
+void mem_init(void)
+{
+ struct at91_pmc *pmc = (struct at91_pmc *)ATMEL_BASE_PMC;
+ struct atmel_mpddr *mpddrc = (struct atmel_mpddr *)ATMEL_BASE_MPDDRC;
+ struct atmel_mpddrc_config ddrc_config;
+ u32 reg;
+
+ ddrc_conf(&ddrc_config);
+
+ at91_periph_clk_enable(ATMEL_ID_MPDDRC);
+ writel(AT91_PMC_DDR, &pmc->scer);
+
+ reg = readl(&mpddrc->io_calibr);
+ reg &= ~ATMEL_MPDDRC_IO_CALIBR_RDIV;
+ reg |= ATMEL_MPDDRC_IO_CALIBR_DDR3_RZQ_55;
+ reg &= ~ATMEL_MPDDRC_IO_CALIBR_TZQIO;
+ reg |= ATMEL_MPDDRC_IO_CALIBR_TZQIO_(101);
+ writel(reg, &mpddrc->io_calibr);
+
+ writel(ATMEL_MPDDRC_RD_DATA_PATH_SHIFT_ONE_CYCLE,
+ &mpddrc->rd_data_path);
+
+ ddr3_init(ATMEL_BASE_MPDDRC, ATMEL_BASE_DDRCS, &ddrc_config);
+
+ writel(0x3, &mpddrc->cal_mr4);
+ writel(64, &mpddrc->tim_cal);
+}
+
+void at91_pmc_init(void)
+{
+ u32 tmp;
+
+ /*
+ * While coming from the ROM code, we run on PLLA @ 492 MHz / 164 MHz,
+ * so we need to slow down and configure MCKR accordingly.
+ * This is why we have a special flavor of the switching function.
+ */
+ tmp = AT91_PMC_MCKR_PLLADIV_2 |
+ AT91_PMC_MCKR_MDIV_3 |
+ AT91_PMC_MCKR_CSS_MAIN;
+ at91_mck_init_down(tmp);
+
+ tmp = AT91_PMC_PLLAR_29 |
+ AT91_PMC_PLLXR_PLLCOUNT(0x3f) |
+ AT91_PMC_PLLXR_MUL(40) |
+ AT91_PMC_PLLXR_DIV(1);
+ at91_plla_init(tmp);
+
+ tmp = AT91_PMC_MCKR_H32MXDIV |
+ AT91_PMC_MCKR_PLLADIV_2 |
+ AT91_PMC_MCKR_MDIV_3 |
+ AT91_PMC_MCKR_CSS_PLLA;
+ at91_mck_init(tmp);
+}
+#endif