| menu "MIPS architecture" |
| depends on MIPS |
| |
| config SYS_ARCH |
| default "mips" |
| |
| config SYS_CPU |
| default "mips32" if CPU_MIPS32 |
| default "mips64" if CPU_MIPS64 |
| |
| choice |
| prompt "Target select" |
| optional |
| |
| config TARGET_MALTA |
| bool "Support malta" |
| select HAS_FIXED_TIMER_FREQUENCY |
| select BOARD_EARLY_INIT_R |
| select DM |
| select DM_SERIAL |
| select PCI |
| select DYNAMIC_IO_PORT_BASE |
| select MIPS_CM |
| select MIPS_INSERT_BOOT_CONFIG |
| select SYS_CACHE_SHIFT_6 |
| select MIPS_L2_CACHE |
| select OF_CONTROL |
| select OF_ISA_BUS |
| select PCI_MAP_SYSTEM_MEMORY |
| select ROM_EXCEPTION_VECTORS |
| select SUPPORTS_BIG_ENDIAN |
| select SUPPORTS_CPU_MIPS32_R1 |
| select SUPPORTS_CPU_MIPS32_R2 |
| select SUPPORTS_CPU_MIPS32_R6 |
| select SUPPORTS_CPU_MIPS64_R1 |
| select SUPPORTS_CPU_MIPS64_R2 |
| select SUPPORTS_CPU_MIPS64_R6 |
| select SUPPORTS_LITTLE_ENDIAN |
| select SWAP_IO_SPACE |
| imply CMD_DM |
| |
| config ARCH_ATH79 |
| bool "Support QCA/Atheros ath79" |
| select HAS_FIXED_TIMER_FREQUENCY |
| select DM |
| select OF_CONTROL |
| imply CMD_DM |
| |
| config ARCH_MSCC |
| bool "Support MSCC VCore-III" |
| select HAS_FIXED_TIMER_FREQUENCY |
| select OF_CONTROL |
| select DM |
| |
| config ARCH_BMIPS |
| bool "Support BMIPS SoCs" |
| select HAS_FIXED_TIMER_FREQUENCY |
| select CLK |
| select CPU |
| select DM |
| select OF_CONTROL |
| select RAM |
| select SYSRESET |
| imply CMD_DM |
| |
| config ARCH_MTMIPS |
| bool "Support MediaTek MIPS platforms" |
| select HAS_FIXED_TIMER_FREQUENCY |
| select CLK |
| imply CMD_DM |
| select DISPLAY_CPUINFO |
| select DM |
| imply DM_GPIO |
| select DM_RESET |
| select DM_SERIAL |
| select PINCTRL |
| select PINMUX |
| select PINCONF |
| select RESET_MTMIPS |
| imply MTD |
| imply DM_SPI |
| imply DM_SPI_FLASH |
| select LAST_STAGE_INIT |
| select MIPS_TUNE_24KC |
| select OF_CONTROL |
| select ROM_EXCEPTION_VECTORS |
| select SUPPORTS_CPU_MIPS32_R1 |
| select SUPPORTS_CPU_MIPS32_R2 |
| select SUPPORTS_LITTLE_ENDIAN |
| select SUPPORT_SPL |
| |
| config ARCH_JZ47XX |
| bool "Support Ingenic JZ47xx" |
| select SUPPORT_SPL |
| select HAS_FIXED_TIMER_FREQUENCY |
| select OF_CONTROL |
| select DM |
| |
| config ARCH_OCTEON |
| bool "Support Marvell Octeon CN7xxx platforms" |
| select ARCH_EARLY_INIT_R |
| select CPU_CAVIUM_OCTEON |
| select DISPLAY_CPUINFO |
| select DMA_ADDR_T_64BIT |
| select DM |
| select DM_GPIO |
| select DM_I2C |
| select DM_SERIAL |
| select DM_SPI |
| select MIPS_L2_CACHE |
| select MIPS_MACH_EARLY_INIT |
| select MIPS_TUNE_OCTEON3 |
| select MTD |
| select ROM_EXCEPTION_VECTORS |
| select SUPPORTS_BIG_ENDIAN |
| select SUPPORTS_CPU_MIPS64_OCTEON |
| select PHYS_64BIT |
| select OF_CONTROL |
| select OF_LIVE |
| imply CMD_DM |
| |
| config MACH_PIC32 |
| bool "Support Microchip PIC32" |
| select HAS_FIXED_TIMER_FREQUENCY |
| select DM |
| select DM_EVENT |
| select OF_CONTROL |
| imply CMD_DM |
| |
| config TARGET_BOSTON |
| bool "Support Boston" |
| select HAS_FIXED_TIMER_FREQUENCY |
| select DM |
| select DM_SERIAL |
| select MIPS_CM |
| select SYS_CACHE_SHIFT_6 |
| select MIPS_L2_CACHE |
| select OF_BOARD_SETUP |
| select OF_CONTROL |
| select ROM_EXCEPTION_VECTORS |
| select SUPPORTS_BIG_ENDIAN |
| select SUPPORTS_CPU_MIPS32_R1 |
| select SUPPORTS_CPU_MIPS32_R2 |
| select SUPPORTS_CPU_MIPS32_R6 |
| select SUPPORTS_CPU_MIPS64_R1 |
| select SUPPORTS_CPU_MIPS64_R2 |
| select SUPPORTS_CPU_MIPS64_R6 |
| select SUPPORTS_LITTLE_ENDIAN |
| imply CMD_DM |
| |
| config TARGET_XILFPGA |
| bool "Support Imagination Xilfpga" |
| select HAS_FIXED_TIMER_FREQUENCY |
| select DM |
| select DM_GPIO |
| select DM_SERIAL |
| select SYS_CACHE_SHIFT_4 |
| select OF_CONTROL |
| select ROM_EXCEPTION_VECTORS |
| select SUPPORTS_CPU_MIPS32_R1 |
| select SUPPORTS_CPU_MIPS32_R2 |
| select SUPPORTS_LITTLE_ENDIAN |
| imply CMD_DM |
| help |
| This supports IMGTEC MIPSfpga platform |
| |
| endchoice |
| |
| source "board/imgtec/boston/Kconfig" |
| source "board/imgtec/malta/Kconfig" |
| source "board/imgtec/xilfpga/Kconfig" |
| source "arch/mips/mach-ath79/Kconfig" |
| source "arch/mips/mach-mscc/Kconfig" |
| source "arch/mips/mach-bmips/Kconfig" |
| source "arch/mips/mach-jz47xx/Kconfig" |
| source "arch/mips/mach-pic32/Kconfig" |
| source "arch/mips/mach-mtmips/Kconfig" |
| source "arch/mips/mach-octeon/Kconfig" |
| |
| if MIPS |
| |
| choice |
| prompt "CPU selection" |
| default CPU_MIPS32_R2 |
| |
| config CPU_MIPS32_R1 |
| bool "MIPS32 Release 1" |
| depends on SUPPORTS_CPU_MIPS32_R1 |
| select 32BIT |
| help |
| Choose this option to build an U-Boot for release 1 through 5 of the |
| MIPS32 architecture. |
| |
| config CPU_MIPS32_R2 |
| bool "MIPS32 Release 2" |
| depends on SUPPORTS_CPU_MIPS32_R2 |
| select 32BIT |
| help |
| Choose this option to build an U-Boot for release 2 through 5 of the |
| MIPS32 architecture. |
| |
| config CPU_MIPS32_R6 |
| bool "MIPS32 Release 6" |
| depends on SUPPORTS_CPU_MIPS32_R6 |
| select 32BIT |
| help |
| Choose this option to build an U-Boot for release 6 or later of the |
| MIPS32 architecture. |
| |
| config CPU_MIPS64_R1 |
| bool "MIPS64 Release 1" |
| depends on SUPPORTS_CPU_MIPS64_R1 |
| select 64BIT |
| help |
| Choose this option to build a kernel for release 1 through 5 of the |
| MIPS64 architecture. |
| |
| config CPU_MIPS64_R2 |
| bool "MIPS64 Release 2" |
| depends on SUPPORTS_CPU_MIPS64_R2 |
| select 64BIT |
| help |
| Choose this option to build a kernel for release 2 through 5 of the |
| MIPS64 architecture. |
| |
| config CPU_MIPS64_R6 |
| bool "MIPS64 Release 6" |
| depends on SUPPORTS_CPU_MIPS64_R6 |
| select 64BIT |
| help |
| Choose this option to build a kernel for release 6 or later of the |
| MIPS64 architecture. |
| |
| config CPU_MIPS64_OCTEON |
| bool "Marvell Octeon series of CPUs" |
| depends on SUPPORTS_CPU_MIPS64_OCTEON |
| select 64BIT |
| help |
| Choose this option for Marvell Octeon CPUs. These CPUs are between |
| MIPS64 R5 and R6 with other extensions. |
| |
| endchoice |
| |
| menu "General setup" |
| |
| config ROM_EXCEPTION_VECTORS |
| bool "Build U-Boot image with exception vectors" |
| help |
| Enable this to include exception vectors in the U-Boot image. This is |
| required if the U-Boot entry point is equal to the address of the |
| CPU reset exception vector (e.g. U-Boot as ROM loader in Qemu, |
| U-Boot booted from parallel NOR flash). |
| Disable this, if the U-Boot image is booted from DRAM (e.g. by SPL). |
| In that case the image size will be reduced by 0x500 bytes. |
| |
| config SYS_MIPS_TIMER_FREQ |
| int "Fixed MIPS CPU timer frequency in Hz" |
| depends on HAS_FIXED_TIMER_FREQUENCY |
| help |
| Configures a fixed CPU timer frequency. |
| |
| config MIPS_CM_BASE |
| hex "MIPS CM GCR Base Address" |
| depends on MIPS_CM |
| default 0x16100000 if TARGET_BOSTON |
| default 0x1fbf8000 |
| help |
| The physical base address at which to map the MIPS Coherence Manager |
| Global Configuration Registers (GCRs). This should be set such that |
| the GCRs occupy a region of the physical address space which is |
| otherwise unused, or at minimum that software doesn't need to access. |
| |
| config MIPS_CACHE_INDEX_BASE |
| hex "Index base address for cache initialisation" |
| default 0x80000000 if CPU_MIPS32 |
| default 0xffffffff80000000 if CPU_MIPS64 |
| help |
| This is the base address for a memory block, which is used for |
| initialising the cache lines. This is also the base address of a memory |
| block which is used for loading and filling cache lines when |
| SYS_MIPS_CACHE_INIT_RAM_LOAD is selected. |
| Normally this is CKSEG0. If the MIPS system needs to move this block |
| to some SRAM or ScratchPad RAM, adapt this option accordingly. |
| |
| config MIPS_MACH_EARLY_INIT |
| bool "Enable mach specific very early init code" |
| help |
| Use this to enable the call to mips_mach_early_init() very early |
| from start.S. This function can be used e.g. to do some very early |
| CPU / SoC intitialization or image copying. Its called very early |
| and at this stage the PC might not match the linking address |
| (CONFIG_TEXT_BASE) - no absolute jump done until this call. |
| |
| config MIPS_CACHE_SETUP |
| bool "Allow generic start code to initialize and setup caches" |
| default n if SKIP_LOWLEVEL_INIT |
| default y |
| help |
| This allows the generic start code to invoke the generic initialization |
| of the CPU caches. Disabling this can be useful for RAM boot scenarios |
| (EJTAG, SPL payload) or for machines which don't need cache initialization |
| or which want to provide their own cache implementation. |
| |
| If unsure, say yes. |
| |
| config MIPS_CACHE_DISABLE |
| bool "Allow generic start code to initially disable caches" |
| default n if SKIP_LOWLEVEL_INIT |
| default y |
| help |
| This allows the generic start code to initially disable the CPU caches |
| and run uncached until the caches are initialized and enabled. Disabling |
| this can be useful on machines which don't need cache initialization or |
| which want to provide their own cache implementation. |
| |
| If unsure, say yes. |
| |
| config MIPS_RELOCATION_TABLE_SIZE |
| hex "Relocation table size" |
| range 0x100 0x10000 |
| default "0x8000" |
| ---help--- |
| A table of relocation data will be appended to the U-Boot binary |
| and parsed in relocate_code() to fix up all offsets in the relocated |
| U-Boot. |
| |
| This option allows the amount of space reserved for the table to be |
| adjusted in a range from 256 up to 64k. The default is 32k and should |
| be ok in most cases. Reduce this value to shrink the size of U-Boot |
| binary. |
| |
| The build will fail and a valid size suggested if this is too small. |
| |
| If unsure, leave at the default value. |
| |
| config RESTORE_EXCEPTION_VECTOR_BASE |
| bool "Restore exception vector base before booting linux kernel" |
| help |
| In U-Boot the exception vector base will be moved to top of memory, |
| to be used to display register dump when exception occurs. |
| But some old linux kernel does not honor the base set in CP0_EBASE. |
| A modified exception vector base will cause kernel crash. |
| |
| This option will restore the exception vector base to its previous |
| value. |
| |
| If unsure, say N. |
| |
| config OVERRIDE_EXCEPTION_VECTOR_BASE |
| bool "Override the exception vector base to be restored" |
| depends on RESTORE_EXCEPTION_VECTOR_BASE |
| help |
| Enable this option if you want to use a different exception vector |
| base rather than the previously saved one. |
| |
| config NEW_EXCEPTION_VECTOR_BASE |
| hex "New exception vector base" |
| depends on OVERRIDE_EXCEPTION_VECTOR_BASE |
| range 0x80000000 0xbffff000 |
| default 0x80000000 |
| help |
| The exception vector base to be restored before booting linux kernel |
| |
| config INIT_STACK_WITHOUT_MALLOC_F |
| bool "Do not reserve malloc space on initial stack" |
| help |
| Enable this option if you don't want to reserve malloc space on |
| initial stack. This is useful if the initial stack can't hold large |
| malloc space. Platform should set the malloc_base later when DRAM is |
| ready to use. |
| |
| config SPL_INIT_STACK_WITHOUT_MALLOC_F |
| bool "Do not reserve malloc space on initial stack in SPL" |
| help |
| Enable this option if you don't want to reserve malloc space on |
| initial stack. This is useful if the initial stack can't hold large |
| malloc space. Platform should set the malloc_base later when DRAM is |
| ready to use. |
| |
| config SPL_LOADER_SUPPORT |
| bool |
| help |
| Enable this option if you want to use SPL loaders without DM enabled. |
| |
| endmenu |
| |
| menu "OS boot interface" |
| |
| config MIPS_BOOT_CMDLINE_LEGACY |
| bool "Hand over legacy command line to Linux kernel" |
| default y |
| help |
| Enable this option if you want U-Boot to hand over the Yamon-style |
| command line to the kernel. All bootargs will be prepared as argc/argv |
| compatible list. The argument count (argc) is stored in register $a0. |
| The address of the argument list (argv) is stored in register $a1. |
| |
| config MIPS_BOOT_ENV_LEGACY |
| bool "Hand over legacy environment to Linux kernel" |
| default y |
| help |
| Enable this option if you want U-Boot to hand over the Yamon-style |
| environment to the kernel. Information like memory size, initrd |
| address and size will be prepared as zero-terminated key/value list. |
| The address of the environment is stored in register $a2. |
| |
| config MIPS_BOOT_FDT |
| bool "Hand over a flattened device tree to Linux kernel" |
| help |
| Enable this option if you want U-Boot to hand over a flattened |
| device tree to the kernel. According to UHI register $a0 will be set |
| to -2 and the FDT address is stored in $a1. |
| |
| endmenu |
| |
| config SUPPORTS_BIG_ENDIAN |
| bool |
| |
| config SUPPORTS_LITTLE_ENDIAN |
| bool |
| |
| config SUPPORTS_CPU_MIPS32_R1 |
| bool |
| |
| config SUPPORTS_CPU_MIPS32_R2 |
| bool |
| |
| config SUPPORTS_CPU_MIPS32_R6 |
| bool |
| |
| config SUPPORTS_CPU_MIPS64_R1 |
| bool |
| |
| config SUPPORTS_CPU_MIPS64_R2 |
| bool |
| |
| config SUPPORTS_CPU_MIPS64_R6 |
| bool |
| |
| config SUPPORTS_CPU_MIPS64_OCTEON |
| bool |
| |
| config HAS_FIXED_TIMER_FREQUENCY |
| bool |
| |
| config CPU_CAVIUM_OCTEON |
| bool |
| |
| config CPU_MIPS32 |
| bool |
| default y if CPU_MIPS32_R1 || CPU_MIPS32_R2 || CPU_MIPS32_R6 |
| |
| config CPU_MIPS64 |
| bool |
| default y if CPU_MIPS64_R1 || CPU_MIPS64_R2 || CPU_MIPS64_R6 |
| default y if CPU_MIPS64_OCTEON |
| |
| config MIPS_TUNE_4KC |
| bool |
| |
| config MIPS_TUNE_14KC |
| bool |
| |
| config MIPS_TUNE_24KC |
| bool |
| |
| config MIPS_TUNE_34KC |
| bool |
| |
| config MIPS_TUNE_74KC |
| bool |
| |
| config MIPS_TUNE_OCTEON3 |
| bool |
| |
| config 32BIT |
| bool |
| |
| config 64BIT |
| bool |
| |
| config SWAP_IO_SPACE |
| bool |
| |
| config SYS_MIPS_CACHE_INIT_RAM_LOAD |
| bool |
| |
| config MIPS_INIT_STACK_IN_SRAM |
| bool |
| help |
| Select this if the initial stack frame could be setup in SRAM. |
| Normally the initial stack frame is set up in DRAM which is often |
| only available after lowlevel_init. With this option the initial |
| stack frame and the early C environment is set up before |
| lowlevel_init. Thus lowlevel_init does not need to be implemented |
| in assembler. |
| |
| config MIPS_SRAM_INIT |
| bool |
| depends on MIPS_INIT_STACK_IN_SRAM |
| help |
| Select this if the SRAM for initial stack needs to be initialized |
| before it can be used. If enabled, a function mips_sram_init() will |
| be called just before setup_stack_gd. |
| |
| config DMA_ADDR_T_64BIT |
| bool |
| help |
| Select this to enable 64-bit DMA addressing |
| |
| config SYS_DCACHE_SIZE |
| int |
| default 0 |
| help |
| The total size of the L1 Dcache, if known at compile time. |
| |
| config SYS_DCACHE_LINE_SIZE |
| int |
| default 0 |
| help |
| The size of L1 Dcache lines, if known at compile time. |
| |
| config SYS_ICACHE_SIZE |
| int |
| default 0 |
| help |
| The total size of the L1 ICache, if known at compile time. |
| |
| config SYS_ICACHE_LINE_SIZE |
| int |
| default 0 |
| help |
| The size of L1 Icache lines, if known at compile time. |
| |
| config SYS_SCACHE_LINE_SIZE |
| int |
| default 0 |
| help |
| The size of L2 cache lines, if known at compile time. |
| |
| |
| config SYS_CACHE_SIZE_AUTO |
| def_bool y if SYS_DCACHE_SIZE = 0 && SYS_ICACHE_SIZE = 0 && \ |
| SYS_DCACHE_LINE_SIZE = 0 && SYS_ICACHE_LINE_SIZE = 0 && \ |
| SYS_SCACHE_LINE_SIZE = 0 |
| help |
| Select this (or let it be auto-selected by not defining any cache |
| sizes) in order to allow U-Boot to automatically detect the sizes |
| of caches at runtime. This has a small cost in code size & runtime |
| so if you know the cache configuration for your system at compile |
| time it would be beneficial to configure it. |
| |
| config MIPS_L2_CACHE |
| bool |
| help |
| Select this if your system includes an L2 cache and you want U-Boot |
| to initialise & maintain it. |
| |
| config DYNAMIC_IO_PORT_BASE |
| bool |
| |
| config MIPS_CM |
| bool |
| help |
| Select this if your system contains a MIPS Coherence Manager and you |
| wish U-Boot to configure it or make use of it to retrieve system |
| information such as cache configuration. |
| |
| config MIPS_INSERT_BOOT_CONFIG |
| bool |
| help |
| Enable this to insert some board-specific boot configuration in |
| the U-Boot binary at offset 0x10. |
| |
| config MIPS_BOOT_CONFIG_WORD0 |
| hex |
| depends on MIPS_INSERT_BOOT_CONFIG |
| default 0x420 if TARGET_MALTA |
| default 0x0 |
| help |
| Value which is inserted as boot config word 0. |
| |
| config MIPS_BOOT_CONFIG_WORD1 |
| hex |
| depends on MIPS_INSERT_BOOT_CONFIG |
| default 0x0 |
| help |
| Value which is inserted as boot config word 1. |
| |
| endif |
| |
| endmenu |