i.mx6q: mx6qsabrelite: Update the network configuration
Define CONFIG_PHY_MICREL, and
minimize the tx clock delay.
There is an issue with 1000 baseTx mode on early revs
of the SabreLite boards. The center tap pin 9 of the mag RJ45
USB combo was connected to the 3.3 filtered supply. Letting
this pin float solved the problem. Symptoms of the problem
were packets with many extra zeroes tacked on the end, and random
bit flips causing a high rate of CRC errors. 10/100 baseTx worked
fine on all revs. To disable 1000 baseTx for these boards, simply
define the environment variable disable_giga. ie.
setenv disable_giga 1
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Acked-by: Dirk Behme <dirk.behme@de.bosch.com>
diff --git a/board/freescale/mx6qsabrelite/mx6qsabrelite.c b/board/freescale/mx6qsabrelite/mx6qsabrelite.c
index 03a088a..f884bb5 100644
--- a/board/freescale/mx6qsabrelite/mx6qsabrelite.c
+++ b/board/freescale/mx6qsabrelite/mx6qsabrelite.c
@@ -29,9 +29,9 @@
#include <asm/gpio.h>
#include <mmc.h>
#include <fsl_esdhc.h>
+#include <micrel.h>
#include <miiphy.h>
#include <netdev.h>
-
DECLARE_GLOBAL_DATA_PTR;
#define UART_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE | \
@@ -214,51 +214,32 @@
}
#endif
-#define MII_1000BASET_CTRL 0x9
-#define MII_EXTENDED_CTRL 0xb
-#define MII_EXTENDED_DATAW 0xc
-
-int fecmxc_mii_postcall(int phy)
+int board_phy_config(struct phy_device *phydev)
{
- /* prefer master mode */
- miiphy_write("FEC", phy, MII_1000BASET_CTRL, 0x0f00);
-
/* min rx data delay */
- miiphy_write("FEC", phy, MII_EXTENDED_CTRL, 0x8105);
- miiphy_write("FEC", phy, MII_EXTENDED_DATAW, 0x0000);
-
- /* max rx/tx clock delay, min rx/tx control delay */
- miiphy_write("FEC", phy, MII_EXTENDED_CTRL, 0x8104);
- miiphy_write("FEC", phy, MII_EXTENDED_DATAW, 0xf0f0);
- miiphy_write("FEC", phy, MII_EXTENDED_CTRL, 0x104);
-
+ ksz9021_phy_extended_write(phydev,
+ MII_KSZ9021_EXT_RGMII_RX_DATA_SKEW, 0x0);
+ /* min tx data delay */
+ ksz9021_phy_extended_write(phydev,
+ MII_KSZ9021_EXT_RGMII_TX_DATA_SKEW, 0x0);
+ /* max rx/tx clock delay, min rx/tx control */
+ ksz9021_phy_extended_write(phydev,
+ MII_KSZ9021_EXT_RGMII_CLOCK_SKEW, 0xf0f0);
+ if (phydev->drv->config)
+ phydev->drv->config(phydev);
+
return 0;
}
int board_eth_init(bd_t *bis)
{
- struct eth_device *dev;
int ret;
setup_iomux_enet();
ret = cpu_eth_init(bis);
- if (ret) {
+ if (ret)
printf("FEC MXC: %s:failed\n", __func__);
- return ret;
- }
-
- dev = eth_get_dev_by_name("FEC");
- if (!dev) {
- printf("FEC MXC: Unable to get FEC device entry\n");
- return -EINVAL;
- }
-
- ret = fecmxc_register_mii_postcall(dev, fecmxc_mii_postcall);
- if (ret) {
- printf("FEC MXC: Unable to register FEC mii postcall\n");
- return ret;
- }
#ifdef CONFIG_MXC_SPI
setup_spi();