sunxi: DT: H3: update board .dts files from Linux
Update the .dts file for the various boards with an Allwinner H3 SoC.
This is as of v4.18-rc3, exactly Linux commit:
commit 721afaa2aeb860067decdddadc84ed16f42f2048 (HEAD)
Merge: 7c00e8ae041b 87815dda5593
Author: Linus Torvalds <torvalds@linux-foundation.org>
Date: Mon Jun 11 17:57:38 2018 -0700
Merge tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
This also includes the OrangePi Zero .dts, which technically has an
Allwinner H2+ SoC.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
diff --git a/arch/arm/dts/sun8i-h2-plus-orangepi-zero.dts b/arch/arm/dts/sun8i-h2-plus-orangepi-zero.dts
index 7c38264..0bc031f 100644
--- a/arch/arm/dts/sun8i-h2-plus-orangepi-zero.dts
+++ b/arch/arm/dts/sun8i-h2-plus-orangepi-zero.dts
@@ -49,7 +49,6 @@
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>
-#include <dt-bindings/pinctrl/sun4i-a10.h>
/ {
model = "Xunlong Orange Pi Zero";
@@ -58,6 +57,7 @@
aliases {
serial0 = &uart0;
/* ethernet0 is the H3 emac, defined in sun8i-h3.dtsi */
+ ethernet0 = &emac;
ethernet1 = &xr819;
};
@@ -92,9 +92,14 @@
wifi_pwrseq: wifi_pwrseq {
compatible = "mmc-pwrseq-simple";
reset-gpios = <&r_pio 0 7 GPIO_ACTIVE_LOW>;
+ post-power-on-delay-ms = <200>;
};
};
+&ehci0 {
+ status = "okay";
+};
+
&ehci1 {
status = "okay";
};
@@ -109,8 +114,7 @@
&mmc0 {
vmmc-supply = <®_vcc3v3>;
bus-width = <4>;
- cd-gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>; /* PF6 */
- cd-inverted;
+ cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */
status = "okay";
};
@@ -130,17 +134,56 @@
};
};
+&ohci0 {
+ status = "okay";
+};
+
&ohci1 {
status = "okay";
};
+&spi0 {
+ /* Disable SPI NOR by default: it optional on Orange Pi Zero boards */
+ status = "disabled";
+
+ flash@0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "mxicy,mx25l1606e", "winbond,w25q128";
+ reg = <0>;
+ spi-max-frequency = <40000000>;
+ };
+};
+
&uart0 {
pinctrl-names = "default";
pinctrl-0 = <&uart0_pins_a>;
status = "okay";
};
-&usbphy {
- /* USB VBUS is always on */
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart1_pins>;
+ status = "disabled";
+};
+
+&uart2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart2_pins>;
+ status = "disabled";
+};
+
+&usb_otg {
+ dr_mode = "peripheral";
status = "okay";
};
+
+&usbphy {
+ /*
+ * USB Type-A port VBUS is always on. However, MicroUSB VBUS can only
+ * power up the board; when it's used as OTG port, this VBUS is
+ * always off even if the board is powered via GPIO pins.
+ */
+ status = "okay";
+ usb0_id_det-gpios = <&pio 6 12 GPIO_ACTIVE_HIGH>; /* PG12 */
+};