net: tsec: Remove non-DM_ETH support code
As DM_ETH is required for all network drivers, it's now safe to remove
the non-DM_ETH support code. Doing this removes some board support code
which was also unused. Finally, this removes some CONFIG symbols that
otherwise needed to be migrated to Kconfig, but were unused in code now.
Signed-off-by: Tom Rini <trini@konsulko.com>
diff --git a/arch/arm/include/asm/arch-ls102xa/config.h b/arch/arm/include/asm/arch-ls102xa/config.h
index 6413a30..14f86df 100644
--- a/arch/arm/include/asm/arch-ls102xa/config.h
+++ b/arch/arm/include/asm/arch-ls102xa/config.h
@@ -36,11 +36,6 @@
#define CFG_SYS_FSL_SEC_OFFSET 0x00700000
#define CFG_SYS_FSL_JR0_OFFSET 0x00710000
-#define CFG_SYS_TSEC1_OFFSET 0x01d10000
-#define CFG_SYS_MDIO1_OFFSET 0x01d24000
-
-#define TSEC_BASE_ADDR (CONFIG_SYS_IMMR + CFG_SYS_TSEC1_OFFSET)
-#define MDIO_BASE_ADDR (CONFIG_SYS_IMMR + CFG_SYS_MDIO1_OFFSET)
#define SCTR_BASE_ADDR (CONFIG_SYS_IMMR + 0x01b00000)
diff --git a/arch/powerpc/include/asm/config_mpc85xx.h b/arch/powerpc/include/asm/config_mpc85xx.h
index d9e5a7d..1b5b494 100644
--- a/arch/powerpc/include/asm/config_mpc85xx.h
+++ b/arch/powerpc/include/asm/config_mpc85xx.h
@@ -24,18 +24,9 @@
#elif defined(CONFIG_ARCH_P1010)
#define CONFIG_FSL_SDHC_V2_3
-#define CONFIG_TSECV2
#define CONFIG_SYS_FSL_IFC_BANK_COUNT 4
-/* P1011 is single core version of P1020 */
-#elif defined(CONFIG_ARCH_P1011)
-#define CONFIG_TSECV2
-
-#elif defined(CONFIG_ARCH_P1020)
-#define CONFIG_TSECV2
-
#elif defined(CONFIG_ARCH_P1021)
-#define CONFIG_TSECV2
#define QE_MURAM_SIZE 0x6000UL
#define MAX_QE_RISC 1
#define QE_NUM_OF_SNUM 28
@@ -47,13 +38,8 @@
#define CFG_SYS_BMAN_NUM_PORTALS 3
#define CFG_SYS_FM_MURAM_SIZE 0x10000
-/* P1024 is lower end variant of P1020 */
-#elif defined(CONFIG_ARCH_P1024)
-#define CONFIG_TSECV2
-
/* P1025 is lower end variant of P1021 */
#elif defined(CONFIG_ARCH_P1025)
-#define CONFIG_TSECV2
#define QE_MURAM_SIZE 0x6000UL
#define MAX_QE_RISC 1
#define QE_NUM_OF_SNUM 28
@@ -108,12 +94,10 @@
#elif defined(CONFIG_ARCH_BSC9131)
#define CONFIG_FSL_SDHC_V2_3
-#define CONFIG_TSECV2
#define CONFIG_SYS_FSL_IFC_BANK_COUNT 3
#elif defined(CONFIG_ARCH_BSC9132)
#define CONFIG_FSL_SDHC_V2_3
-#define CONFIG_TSECV2
#define CONFIG_SYS_FSL_IFC_BANK_COUNT 3
#elif defined(CONFIG_ARCH_T4240)
@@ -221,7 +205,6 @@
#elif defined(CONFIG_ARCH_C29X)
#define CONFIG_FSL_SDHC_V2_3
-#define CONFIG_TSECV2_1
#define CONFIG_SYS_FSL_IFC_BANK_COUNT 8
#define CFG_SYS_FSL_SEC_IDX_OFFSET 0x20000
diff --git a/arch/powerpc/include/asm/immap_83xx.h b/arch/powerpc/include/asm/immap_83xx.h
index 19774f3..24bd438 100644
--- a/arch/powerpc/include/asm/immap_83xx.h
+++ b/arch/powerpc/include/asm/immap_83xx.h
@@ -873,9 +873,4 @@
#define CFG_SYS_LBC_ADDR (&((immap_t *)CONFIG_SYS_IMMR)->im_lbc)
-#define CFG_SYS_TSEC1_OFFSET 0x24000
-#define CFG_SYS_MDIO1_OFFSET 0x24000
-
-#define TSEC_BASE_ADDR (CONFIG_SYS_IMMR + CFG_SYS_TSEC1_OFFSET)
-#define MDIO_BASE_ADDR (CONFIG_SYS_IMMR + CFG_SYS_MDIO1_OFFSET)
#endif /* __IMMAP_83xx__ */
diff --git a/arch/powerpc/include/asm/immap_85xx.h b/arch/powerpc/include/asm/immap_85xx.h
index 283fdf3..7293720 100644
--- a/arch/powerpc/include/asm/immap_85xx.h
+++ b/arch/powerpc/include/asm/immap_85xx.h
@@ -2541,13 +2541,6 @@
#define CFG_SYS_MPC85xx_USB2_OFFSET 0x23000
#define CFG_SYS_MPC85xx_USB1_PHY_OFFSET 0xE5000
#define CFG_SYS_MPC85xx_USB2_PHY_OFFSET 0xE5100
-#ifdef CONFIG_TSECV2
-#define CFG_SYS_TSEC1_OFFSET 0xB0000
-#elif defined(CONFIG_TSECV2_1)
-#define CFG_SYS_TSEC1_OFFSET 0x10000
-#else
-#define CFG_SYS_TSEC1_OFFSET 0x24000
-#endif
#define CFG_SYS_MDIO1_OFFSET 0x24000
#define CFG_SYS_MPC85xx_ESDHC_OFFSET 0x2e000
#if defined(CONFIG_ARCH_C29X)
@@ -2673,7 +2666,6 @@
#define CFG_SYS_SEC_MON_ADDR \
(CONFIG_SYS_IMMR + CFG_SYS_SEC_MON_OFFSET)
-#define TSEC_BASE_ADDR (CONFIG_SYS_IMMR + CFG_SYS_TSEC1_OFFSET)
#define MDIO_BASE_ADDR (CONFIG_SYS_IMMR + CFG_SYS_MDIO1_OFFSET)
#ifdef CONFIG_SYS_FSL_QORIQ_CHASSIS2
diff --git a/board/freescale/common/pixis.c b/board/freescale/common/pixis.c
index 6fdb110..cb9f454 100644
--- a/board/freescale/common/pixis.c
+++ b/board/freescale/common/pixis.c
@@ -281,79 +281,6 @@
""
);
-#ifdef CONFIG_PIXIS_SGMII_CMD
-
-/* Enable or disable SGMII mode for a TSEC
- */
-static int pixis_set_sgmii(struct cmd_tbl *cmdtp, int flag, int argc,
- char *const argv[])
-{
- int which_tsec = -1;
- unsigned char mask;
- unsigned char switch_mask;
-
- if ((argc > 2) && (strcmp(argv[1], "all") != 0))
- which_tsec = simple_strtoul(argv[1], NULL, 0);
-
- switch (which_tsec) {
-#ifdef CONFIG_TSEC1
- case 1:
- mask = PIXIS_VSPEED2_TSEC1SER;
- switch_mask = PIXIS_VCFGEN1_TSEC1SER;
- break;
-#endif
-#ifdef CONFIG_TSEC2
- case 2:
- mask = PIXIS_VSPEED2_TSEC2SER;
- switch_mask = PIXIS_VCFGEN1_TSEC2SER;
- break;
-#endif
-#ifdef CONFIG_TSEC3
- case 3:
- mask = PIXIS_VSPEED2_TSEC3SER;
- switch_mask = PIXIS_VCFGEN1_TSEC3SER;
- break;
-#endif
-#ifdef CONFIG_TSEC4
- case 4:
- mask = PIXIS_VSPEED2_TSEC4SER;
- switch_mask = PIXIS_VCFGEN1_TSEC4SER;
- break;
-#endif
- default:
- mask = PIXIS_VSPEED2_MASK;
- switch_mask = PIXIS_VCFGEN1_MASK;
- break;
- }
-
- /* Toggle whether the switches or FPGA control the settings */
- if (!strcmp(argv[argc - 1], "switch"))
- clrbits_8(pixis_base + PIXIS_VCFGEN1, switch_mask);
- else
- setbits_8(pixis_base + PIXIS_VCFGEN1, switch_mask);
-
- /* If it's not the switches, enable or disable SGMII, as specified */
- if (!strcmp(argv[argc - 1], "on"))
- clrbits_8(pixis_base + PIXIS_VSPEED2, mask);
- else if (!strcmp(argv[argc - 1], "off"))
- setbits_8(pixis_base + PIXIS_VSPEED2, mask);
-
- return 0;
-}
-
-U_BOOT_CMD(
- pixis_set_sgmii, CONFIG_SYS_MAXARGS, 1, pixis_set_sgmii,
- "pixis_set_sgmii"
- " - Enable or disable SGMII mode for a given TSEC \n",
- "\npixis_set_sgmii [TSEC num] <on|off|switch>\n"
- " TSEC num: 1,2,3,4 or 'all'. 'all' is default.\n"
- " on - enables SGMII\n"
- " off - disables SGMII\n"
- " switch - use switch settings"
-);
-
-#endif
-
/*
* This function takes the non-integral cpu:mpx pll ratio
* and converts it to an integer that can be used to assign
diff --git a/board/freescale/mpc8548cds/mpc8548cds.c b/board/freescale/mpc8548cds/mpc8548cds.c
index 73e024e..ec6e3a2 100644
--- a/board/freescale/mpc8548cds/mpc8548cds.c
+++ b/board/freescale/mpc8548cds/mpc8548cds.c
@@ -168,85 +168,3 @@
#endif /* enable SDRAM init */
}
-
-#ifndef CONFIG_DM_ETH
-static void configure_rgmii(void)
-{
- unsigned short temp;
-
- /* Change the resistors for the PHY */
- /* This is needed to get the RGMII working for the 1.3+
- * CDS cards */
- if (get_board_version() == 0x13) {
- miiphy_write(DEFAULT_MII_NAME,
- TSEC1_PHY_ADDR, 29, 18);
-
- miiphy_read(DEFAULT_MII_NAME,
- TSEC1_PHY_ADDR, 30, &temp);
-
- temp = (temp & 0xf03f);
- temp |= 2 << 9; /* 36 ohm */
- temp |= 2 << 6; /* 39 ohm */
-
- miiphy_write(DEFAULT_MII_NAME,
- TSEC1_PHY_ADDR, 30, temp);
-
- miiphy_write(DEFAULT_MII_NAME,
- TSEC1_PHY_ADDR, 29, 3);
-
- miiphy_write(DEFAULT_MII_NAME,
- TSEC1_PHY_ADDR, 30, 0x8000);
- }
-
- return;
-}
-
-int board_eth_init(struct bd_info *bis)
-{
-#ifdef CONFIG_TSEC_ENET
- struct fsl_pq_mdio_info mdio_info;
- struct tsec_info_struct tsec_info[4];
- int num = 0;
-
-#ifdef CONFIG_TSEC1
- SET_STD_TSEC_INFO(tsec_info[num], 1);
- num++;
-#endif
-#ifdef CONFIG_TSEC2
- SET_STD_TSEC_INFO(tsec_info[num], 2);
- num++;
-#endif
-#ifdef CONFIG_TSEC3
- /* initialize TSEC3 only if Carrier is 1.3 or above on CDS */
- if (get_board_version() >= 0x13) {
- SET_STD_TSEC_INFO(tsec_info[num], 3);
- tsec_info[num].interface = PHY_INTERFACE_MODE_RGMII_ID;
- num++;
- }
-#endif
-#ifdef CONFIG_TSEC4
- /* initialize TSEC4 only if Carrier is 1.3 or above on CDS */
- if (get_board_version() >= 0x13) {
- SET_STD_TSEC_INFO(tsec_info[num], 4);
- tsec_info[num].interface = PHY_INTERFACE_MODE_RGMII_ID;
- num++;
- }
-#endif
-
- if (!num) {
- printf("No TSECs initialized\n");
-
- return 0;
- }
-
- mdio_info.regs = (struct tsec_mii_mng *)CONFIG_SYS_MDIO_BASE_ADDR;
- mdio_info.name = DEFAULT_MII_NAME;
- fsl_pq_mdio_init(bis, &mdio_info);
-
- tsec_eth_init(bis, tsec_info, num);
- configure_rgmii();
-#endif
-
- return pci_eth_init(bis);
-}
-#endif
diff --git a/board/freescale/p1010rdb/p1010rdb.c b/board/freescale/p1010rdb/p1010rdb.c
index 0f01482..d32274b 100644
--- a/board/freescale/p1010rdb/p1010rdb.c
+++ b/board/freescale/p1010rdb/p1010rdb.c
@@ -478,49 +478,6 @@
return 0;
}
-#ifndef CONFIG_DM_ETH
-int board_eth_init(struct bd_info *bis)
-{
-#ifdef CONFIG_TSEC_ENET
- struct fsl_pq_mdio_info mdio_info;
- struct tsec_info_struct tsec_info[4];
- struct cpu_type *cpu;
- int num = 0;
-
- cpu = gd->arch.cpu;
-
-#ifdef CONFIG_TSEC1
- SET_STD_TSEC_INFO(tsec_info[num], 1);
- num++;
-#endif
-#ifdef CONFIG_TSEC2
- SET_STD_TSEC_INFO(tsec_info[num], 2);
- num++;
-#endif
-#ifdef CONFIG_TSEC3
- /* P1014 and it's derivatives do not support eTSEC3 */
- if (cpu->soc_ver != SVR_P1014) {
- SET_STD_TSEC_INFO(tsec_info[num], 3);
- num++;
- }
-#endif
- if (!num) {
- printf("No TSECs initialized\n");
- return 0;
- }
-
- mdio_info.regs = (struct tsec_mii_mng *)CONFIG_SYS_MDIO_BASE_ADDR;
- mdio_info.name = DEFAULT_MII_NAME;
-
- fsl_pq_mdio_init(bis, &mdio_info);
-
- tsec_eth_init(bis, tsec_info, num);
-#endif
-
- return pci_eth_init(bis);
-}
-#endif
-
#if defined(CONFIG_OF_BOARD_SETUP)
void fdt_del_flexcan(void *blob)
{
diff --git a/board/freescale/p1_p2_rdb_pc/p1_p2_rdb_pc.c b/board/freescale/p1_p2_rdb_pc/p1_p2_rdb_pc.c
index ab79724..df9f6ae 100644
--- a/board/freescale/p1_p2_rdb_pc/p1_p2_rdb_pc.c
+++ b/board/freescale/p1_p2_rdb_pc/p1_p2_rdb_pc.c
@@ -364,56 +364,6 @@
return 0;
}
-#ifndef CONFIG_DM_ETH
-int board_eth_init(struct bd_info *bis)
-{
- struct fsl_pq_mdio_info mdio_info;
- struct tsec_info_struct tsec_info[4];
- ccsr_gur_t *gur __attribute__((unused)) =
- (void *)(CFG_SYS_MPC85xx_GUTS_ADDR);
- int num = 0;
-
-#ifdef CONFIG_TSEC1
- SET_STD_TSEC_INFO(tsec_info[num], 1);
- num++;
-#endif
-#ifdef CONFIG_TSEC2
- SET_STD_TSEC_INFO(tsec_info[num], 2);
- if (is_serdes_configured(SGMII_TSEC2)) {
- printf("eTSEC2 is in sgmii mode.\n");
- tsec_info[num].flags |= TSEC_SGMII;
- }
- num++;
-#endif
-#ifdef CONFIG_TSEC3
- SET_STD_TSEC_INFO(tsec_info[num], 3);
- num++;
-#endif
-
- if (!num) {
- printf("No TSECs initialized\n");
- return 0;
- }
-
- mdio_info.regs = TSEC_GET_MDIO_REGS_BASE(1);
- mdio_info.name = DEFAULT_MII_NAME;
-
- fsl_pq_mdio_init(bis, &mdio_info);
-
- tsec_eth_init(bis, tsec_info, num);
-
-#if defined(CONFIG_UEC_ETH)
- /* QE0 and QE3 need to be exposed for UCC1 and UCC5 Eth mode */
- setbits_be32(&gur->pmuxcr, MPC85xx_PMUXCR_QE0);
- setbits_be32(&gur->pmuxcr, MPC85xx_PMUXCR_QE3);
-
- uec_standard_init(bis);
-#endif
-
- return pci_eth_init(bis);
-}
-#endif
-
#if defined(CONFIG_OF_BOARD_SETUP) || defined(CONFIG_OF_BOARD_FIXUP)
static void fix_max6370_watchdog(void *blob)
{
diff --git a/drivers/net/tsec.c b/drivers/net/tsec.c
index 8b6f034..f465409 100644
--- a/drivers/net/tsec.c
+++ b/drivers/net/tsec.c
@@ -22,34 +22,6 @@
#include <asm/processor.h>
#include <asm/io.h>
-#ifndef CONFIG_DM_ETH
-/* Default initializations for TSEC controllers. */
-
-static struct tsec_info_struct tsec_info[] = {
-#ifdef CONFIG_TSEC1
- STD_TSEC_INFO(1), /* TSEC1 */
-#endif
-#ifdef CONFIG_TSEC2
- STD_TSEC_INFO(2), /* TSEC2 */
-#endif
-#ifdef CONFIG_MPC85XX_FEC
- {
- .regs = TSEC_GET_REGS(2, 0x2000),
- .devname = CONFIG_MPC85XX_FEC_NAME,
- .phyaddr = FEC_PHY_ADDR,
- .flags = FEC_FLAGS,
- .mii_devname = DEFAULT_MII_NAME
- }, /* FEC */
-#endif
-#ifdef CONFIG_TSEC3
- STD_TSEC_INFO(3), /* TSEC3 */
-#endif
-#ifdef CONFIG_TSEC4
- STD_TSEC_INFO(4), /* TSEC4 */
-#endif
-};
-#endif /* CONFIG_DM_ETH */
-
#define TBIANA_SETTINGS ( \
TBIANA_ASYMMETRIC_PAUSE \
| TBIANA_SYMMETRIC_PAUSE \
@@ -124,23 +96,14 @@
* for PowerPC (tm) is usually the case) in the register holds
* the entry.
*/
-#ifndef CONFIG_DM_ETH
-static int tsec_mcast_addr(struct eth_device *dev, const u8 *mcast_mac,
- int join)
-#else
static int tsec_mcast_addr(struct udevice *dev, const u8 *mcast_mac, int join)
-#endif
{
struct tsec_private *priv;
struct tsec __iomem *regs;
u32 result, value;
u8 whichbit, whichreg;
-#ifndef CONFIG_DM_ETH
- priv = (struct tsec_private *)dev->priv;
-#else
priv = dev_get_priv(dev);
-#endif
regs = priv->regs;
result = ether_crc(MAC_ADDR_LEN, mcast_mac);
whichbit = (result >> 24) & 0x1f; /* the 5 LSB = which bit to set */
@@ -271,11 +234,7 @@
* do the same. Presumably, this would be zero if there were no
* errors
*/
-#ifndef CONFIG_DM_ETH
-static int tsec_send(struct eth_device *dev, void *packet, int length)
-#else
static int tsec_send(struct udevice *dev, void *packet, int length)
-#endif
{
struct tsec_private *priv;
struct tsec __iomem *regs;
@@ -283,11 +242,7 @@
u16 status;
int i;
-#ifndef CONFIG_DM_ETH
- priv = (struct tsec_private *)dev->priv;
-#else
priv = dev_get_priv(dev);
-#endif
regs = priv->regs;
/* Find an empty buffer descriptor */
for (i = 0;
@@ -324,42 +279,6 @@
return result;
}
-#ifndef CONFIG_DM_ETH
-static int tsec_recv(struct eth_device *dev)
-{
- struct tsec_private *priv = (struct tsec_private *)dev->priv;
- struct tsec __iomem *regs = priv->regs;
-
- while (!(in_be16(&priv->rxbd[priv->rx_idx].status) & RXBD_EMPTY)) {
- int length = in_be16(&priv->rxbd[priv->rx_idx].length);
- u16 status = in_be16(&priv->rxbd[priv->rx_idx].status);
- uchar *packet = net_rx_packets[priv->rx_idx];
-
- /* Send the packet up if there were no errors */
- if (!(status & RXBD_STATS))
- net_process_received_packet(packet, length - 4);
- else
- printf("Got error %x\n", (status & RXBD_STATS));
-
- out_be16(&priv->rxbd[priv->rx_idx].length, 0);
-
- status = RXBD_EMPTY;
- /* Set the wrap bit if this is the last element in the list */
- if ((priv->rx_idx + 1) == PKTBUFSRX)
- status |= RXBD_WRAP;
- out_be16(&priv->rxbd[priv->rx_idx].status, status);
-
- priv->rx_idx = (priv->rx_idx + 1) % PKTBUFSRX;
- }
-
- if (in_be32(®s->ievent) & IEVENT_BSY) {
- out_be32(®s->ievent, IEVENT_BSY);
- out_be32(®s->rstat, RSTAT_CLEAR_RHALT);
- }
-
- return -1;
-}
-#else
static int tsec_recv(struct udevice *dev, int flags, uchar **packetp)
{
struct tsec_private *priv = (struct tsec_private *)dev_get_priv(dev);
@@ -406,22 +325,12 @@
return 0;
}
-#endif
-/* Stop the interface */
-#ifndef CONFIG_DM_ETH
-static void tsec_halt(struct eth_device *dev)
-#else
static void tsec_halt(struct udevice *dev)
-#endif
{
struct tsec_private *priv;
struct tsec __iomem *regs;
-#ifndef CONFIG_DM_ETH
- priv = (struct tsec_private *)dev->priv;
-#else
priv = dev_get_priv(dev);
-#endif
regs = priv->regs;
clrbits_be32(®s->dmactrl, DMACTRL_GRS | DMACTRL_GTS);
@@ -583,27 +492,15 @@
* that it returns success if the link is up, failure otherwise.
* This allows U-Boot to find the first active controller.
*/
-#ifndef CONFIG_DM_ETH
-static int tsec_init(struct eth_device *dev, struct bd_info *bd)
-#else
static int tsec_init(struct udevice *dev)
-#endif
{
struct tsec_private *priv;
struct tsec __iomem *regs;
-#ifdef CONFIG_DM_ETH
struct eth_pdata *pdata = dev_get_plat(dev);
-#else
- struct eth_device *pdata = dev;
-#endif
u32 tempval;
int ret;
-#ifndef CONFIG_DM_ETH
- priv = (struct tsec_private *)dev->priv;
-#else
priv = dev_get_priv(dev);
-#endif
regs = priv->regs;
/* Make sure the controller is stopped */
tsec_halt(dev);
@@ -715,7 +612,7 @@
if (priv->interface == PHY_INTERFACE_MODE_SGMII)
tsec_configure_serdes(priv);
-#if defined(CONFIG_DM_ETH) && defined(CONFIG_DM_MDIO)
+#if defined(CONFIG_DM_MDIO)
phydev = dm_eth_phy_connect(priv->dev);
#else
phydev = phy_connect(priv->bus, priv->phyaddr, priv->dev,
@@ -734,99 +631,6 @@
return 1;
}
-#ifndef CONFIG_DM_ETH
-/*
- * Initialize device structure. Returns success if PHY
- * initialization succeeded (i.e. if it recognizes the PHY)
- */
-static int tsec_initialize(struct bd_info *bis,
- struct tsec_info_struct *tsec_info)
-{
- struct tsec_private *priv;
- struct eth_device *dev;
- int i;
-
- dev = (struct eth_device *)malloc(sizeof(*dev));
-
- if (!dev)
- return 0;
-
- memset(dev, 0, sizeof(*dev));
-
- priv = (struct tsec_private *)malloc(sizeof(*priv));
-
- if (!priv) {
- free(dev);
- return 0;
- }
-
- priv->regs = tsec_info->regs;
- priv->phyregs_sgmii = tsec_info->miiregs_sgmii;
-
- priv->phyaddr = tsec_info->phyaddr;
- priv->tbiaddr = CFG_SYS_TBIPA_VALUE;
- priv->flags = tsec_info->flags;
-
- strcpy(dev->name, tsec_info->devname);
- priv->interface = tsec_info->interface;
- priv->bus = miiphy_get_dev_by_name(tsec_info->mii_devname);
- priv->dev = dev;
- dev->iobase = 0;
- dev->priv = priv;
- dev->init = tsec_init;
- dev->halt = tsec_halt;
- dev->send = tsec_send;
- dev->recv = tsec_recv;
- dev->mcast = tsec_mcast_addr;
-
- /* Tell U-Boot to get the addr from the env */
- for (i = 0; i < 6; i++)
- dev->enetaddr[i] = 0;
-
- eth_register(dev);
-
- /* Reset the MAC */
- setbits_be32(&priv->regs->maccfg1, MACCFG1_SOFT_RESET);
- udelay(2); /* Soft Reset must be asserted for 3 TX clocks */
- clrbits_be32(&priv->regs->maccfg1, MACCFG1_SOFT_RESET);
-
- /* Try to initialize PHY here, and return */
- return init_phy(priv);
-}
-
-/*
- * Initialize all the TSEC devices
- *
- * Returns the number of TSEC devices that were initialized
- */
-int tsec_eth_init(struct bd_info *bis, struct tsec_info_struct *tsecs,
- int num)
-{
- int i;
- int count = 0;
-
- for (i = 0; i < num; i++) {
- int ret = tsec_initialize(bis, &tsecs[i]);
-
- if (ret > 0)
- count += ret;
- }
-
- return count;
-}
-
-int tsec_standard_init(struct bd_info *bis)
-{
- struct fsl_pq_mdio_info info;
-
- info.regs = TSEC_GET_MDIO_REGS_BASE(1);
- info.name = DEFAULT_MII_NAME;
-
- fsl_pq_mdio_init(bis, &info);
-
- return tsec_eth_init(bis, tsec_info, ARRAY_SIZE(tsec_info));
-}
-#else /* CONFIG_DM_ETH */
int tsec_probe(struct udevice *dev)
{
struct eth_pdata *pdata = dev_get_plat(dev);
@@ -966,4 +770,3 @@
.plat_auto = sizeof(struct eth_pdata),
.flags = DM_FLAG_ALLOC_PRIV_DMA,
};
-#endif /* CONFIG_DM_ETH */
diff --git a/include/configs/MPC837XERDB.h b/include/configs/MPC837XERDB.h
index 95a9019..f312ffb 100644
--- a/include/configs/MPC837XERDB.h
+++ b/include/configs/MPC837XERDB.h
@@ -41,8 +41,6 @@
#ifdef CONFIG_VSC7385_ENET
-#define CONFIG_TSEC2
-
/* The flash address and size of the VSC7385 firmware image */
#define CONFIG_VSC7385_IMAGE 0xFE7FE000
#define CONFIG_VSC7385_IMAGE_SIZE 8192
@@ -178,31 +176,6 @@
#define CFG_SYS_PCIE2_MEM_PHYS 0xC8000000
#define CFG_SYS_PCIE2_IO_PHYS 0xD8000000
-/*
- * TSEC
- */
-#ifdef CONFIG_TSEC_ENET
-
-#define CONFIG_GMII /* MII PHY management */
-
-#define CONFIG_TSEC1
-
-#ifdef CONFIG_TSEC1
-#define CONFIG_TSEC1_NAME "TSEC0"
-#define CFG_SYS_TSEC1_OFFSET 0x24000
-#define TSEC1_PHY_ADDR 2
-#define TSEC1_FLAGS (TSEC_GIGABIT | TSEC_REDUCED)
-#define TSEC1_PHYIDX 0
-#endif
-
-#ifdef CONFIG_TSEC2
-#define CONFIG_TSEC2_NAME "TSEC1"
-#define TSEC2_PHY_ADDR 0x1c
-#define TSEC2_FLAGS (TSEC_GIGABIT | TSEC_REDUCED)
-#define TSEC2_PHYIDX 0
-#endif
-#endif
-
#ifdef CONFIG_MMC
#define CONFIG_FSL_ESDHC_PIN_MUX
#define CFG_SYS_FSL_ESDHC_ADDR CFG_SYS_MPC83xx_ESDHC_ADDR
diff --git a/include/configs/MPC8548CDS.h b/include/configs/MPC8548CDS.h
index 780ee5a..34b876f 100644
--- a/include/configs/MPC8548CDS.h
+++ b/include/configs/MPC8548CDS.h
@@ -283,33 +283,6 @@
#endif
#define CFG_SYS_SRIO1_MEM_SIZE 0x20000000 /* 512M */
-#if defined(CONFIG_TSEC_ENET)
-
-#define CONFIG_TSEC1 1
-#define CONFIG_TSEC1_NAME "eTSEC0"
-#define CONFIG_TSEC2 1
-#define CONFIG_TSEC2_NAME "eTSEC1"
-#define CONFIG_TSEC3 1
-#define CONFIG_TSEC3_NAME "eTSEC2"
-#define CONFIG_TSEC4
-#define CONFIG_TSEC4_NAME "eTSEC3"
-#undef CONFIG_MPC85XX_FEC
-
-#define TSEC1_PHY_ADDR 0
-#define TSEC2_PHY_ADDR 1
-#define TSEC3_PHY_ADDR 2
-#define TSEC4_PHY_ADDR 3
-
-#define TSEC1_PHYIDX 0
-#define TSEC2_PHYIDX 0
-#define TSEC3_PHYIDX 0
-#define TSEC4_PHYIDX 0
-#define TSEC1_FLAGS TSEC_GIGABIT
-#define TSEC2_FLAGS TSEC_GIGABIT
-#define TSEC3_FLAGS (TSEC_GIGABIT | TSEC_REDUCED)
-#define TSEC4_FLAGS (TSEC_GIGABIT | TSEC_REDUCED)
-#endif /* CONFIG_TSEC_ENET */
-
/*
* Miscellaneous configurable options
*/
diff --git a/include/configs/P1010RDB.h b/include/configs/P1010RDB.h
index b1d6b15..4418d51 100644
--- a/include/configs/P1010RDB.h
+++ b/include/configs/P1010RDB.h
@@ -349,37 +349,6 @@
/* eSPI - Enhanced SPI */
#endif
-#if defined(CONFIG_TSEC_ENET)
-#define CONFIG_MII_DEFAULT_TSEC 1 /* Allow unregistered phys */
-#define CONFIG_TSEC1 1
-#define CONFIG_TSEC1_NAME "eTSEC1"
-#define CONFIG_TSEC2 1
-#define CONFIG_TSEC2_NAME "eTSEC2"
-#define CONFIG_TSEC3 1
-#define CONFIG_TSEC3_NAME "eTSEC3"
-
-#define TSEC1_PHY_ADDR 1
-#define TSEC2_PHY_ADDR 0
-#define TSEC3_PHY_ADDR 2
-
-#define TSEC1_FLAGS (TSEC_GIGABIT | TSEC_REDUCED)
-#define TSEC2_FLAGS (TSEC_GIGABIT | TSEC_REDUCED)
-#define TSEC3_FLAGS (TSEC_GIGABIT | TSEC_REDUCED)
-
-#define TSEC1_PHYIDX 0
-#define TSEC2_PHYIDX 0
-#define TSEC3_PHYIDX 0
-
-/* TBI PHY configuration for SGMII mode */
-#define CONFIG_TSEC_TBICR_SETTINGS ( \
- TBICR_PHY_RESET \
- | TBICR_ANEG_ENABLE \
- | TBICR_FULL_DUPLEX \
- | TBICR_SPEED1_SET \
- )
-
-#endif /* CONFIG_TSEC_ENET */
-
#ifdef CONFIG_MMC
#define CFG_SYS_FSL_ESDHC_ADDR CFG_SYS_MPC85xx_ESDHC_ADDR
#endif
diff --git a/include/configs/ls1021aiot.h b/include/configs/ls1021aiot.h
index 024a718..179c5128 100644
--- a/include/configs/ls1021aiot.h
+++ b/include/configs/ls1021aiot.h
@@ -66,27 +66,6 @@
/* SPI */
-/*
- * eTSEC
- */
-
-#ifdef CONFIG_TSEC_ENET
-#define CONFIG_MII_DEFAULT_TSEC 1
-#define CONFIG_TSEC1 1
-#define CONFIG_TSEC1_NAME "eTSEC1"
-#define CONFIG_TSEC2 1
-#define CONFIG_TSEC2_NAME "eTSEC2"
-
-#define TSEC1_PHY_ADDR 1
-#define TSEC2_PHY_ADDR 3
-
-#define TSEC1_FLAGS (TSEC_GIGABIT | TSEC_REDUCED)
-#define TSEC2_FLAGS (TSEC_GIGABIT | TSEC_REDUCED)
-
-#define TSEC1_PHYIDX 0
-#define TSEC2_PHYIDX 0
-#endif
-
#define FSL_PCIE_COMPAT "fsl,ls1021a-pcie"
#define CONFIG_PEN_ADDR_BIG_ENDIAN
diff --git a/include/configs/ls1021aqds.h b/include/configs/ls1021aqds.h
index 5a91cc3..d6681e8 100644
--- a/include/configs/ls1021aqds.h
+++ b/include/configs/ls1021aqds.h
@@ -247,32 +247,6 @@
* MMC
*/
-/*
- * eTSEC
- */
-
-#ifdef CONFIG_TSEC_ENET
-#define CONFIG_MII_DEFAULT_TSEC 3
-#define CONFIG_TSEC1 1
-#define CONFIG_TSEC1_NAME "eTSEC1"
-#define CONFIG_TSEC2 1
-#define CONFIG_TSEC2_NAME "eTSEC2"
-#define CONFIG_TSEC3 1
-#define CONFIG_TSEC3_NAME "eTSEC3"
-
-#define TSEC1_PHY_ADDR 1
-#define TSEC2_PHY_ADDR 2
-#define TSEC3_PHY_ADDR 3
-
-#define TSEC1_FLAGS (TSEC_GIGABIT | TSEC_REDUCED)
-#define TSEC2_FLAGS (TSEC_GIGABIT | TSEC_REDUCED)
-#define TSEC3_FLAGS (TSEC_GIGABIT | TSEC_REDUCED)
-
-#define TSEC1_PHYIDX 0
-#define TSEC2_PHYIDX 0
-#define TSEC3_PHYIDX 0
-#endif
-
#define CONFIG_PEN_ADDR_BIG_ENDIAN
#define CONFIG_SMP_PEN_ADDR 0x01ee0200
diff --git a/include/configs/p1_p2_rdb_pc.h b/include/configs/p1_p2_rdb_pc.h
index 9738e9f..49c5aef 100644
--- a/include/configs/p1_p2_rdb_pc.h
+++ b/include/configs/p1_p2_rdb_pc.h
@@ -366,27 +366,6 @@
#endif
#endif /* CONFIG_PCI */
-#if defined(CONFIG_TSEC_ENET)
-#define CONFIG_TSEC1
-#define CONFIG_TSEC1_NAME "eTSEC1"
-#define CONFIG_TSEC2
-#define CONFIG_TSEC2_NAME "eTSEC2"
-#define CONFIG_TSEC3
-#define CONFIG_TSEC3_NAME "eTSEC3"
-
-#define TSEC1_PHY_ADDR 2
-#define TSEC2_PHY_ADDR 0
-#define TSEC3_PHY_ADDR 1
-
-#define TSEC1_FLAGS (TSEC_GIGABIT | TSEC_REDUCED)
-#define TSEC2_FLAGS (TSEC_GIGABIT | TSEC_REDUCED)
-#define TSEC3_FLAGS (TSEC_GIGABIT | TSEC_REDUCED)
-
-#define TSEC1_PHYIDX 0
-#define TSEC2_PHYIDX 0
-#define TSEC3_PHYIDX 0
-#endif /* CONFIG_TSEC_ENET */
-
/*
* Environment
*/
diff --git a/include/configs/socrates.h b/include/configs/socrates.h
index 95393d3..2a07671 100644
--- a/include/configs/socrates.h
+++ b/include/configs/socrates.h
@@ -111,22 +111,6 @@
#define CFG_SYS_PCI1_MEM_PHYS 0x80000000
#define CFG_SYS_PCI1_IO_PHYS 0xE2000000
-#define CONFIG_TSEC1 1
-#define CONFIG_TSEC1_NAME "TSEC0"
-#define CONFIG_TSEC3 1
-#define CONFIG_TSEC3_NAME "TSEC1"
-#undef CONFIG_MPC85XX_FEC
-
-#define TSEC1_PHY_ADDR 0
-#define TSEC3_PHY_ADDR 1
-
-#define TSEC1_PHYIDX 0
-#define TSEC3_PHYIDX 0
-#define TSEC1_FLAGS TSEC_GIGABIT
-#define TSEC3_FLAGS TSEC_GIGABIT
-
-/* Options are: TSEC[0,1] */
-
/*
* Miscellaneous configurable options
*/
diff --git a/include/tsec.h b/include/tsec.h
index de279b2..1533378 100644
--- a/include/tsec.h
+++ b/include/tsec.h
@@ -19,56 +19,6 @@
#define TSEC_MDIO_REGS_OFFSET 0x520
-#ifndef CONFIG_DM_ETH
-
-#ifdef CONFIG_ARCH_LS1021A
-#define TSEC_SIZE 0x40000
-#define TSEC_MDIO_OFFSET 0x40000
-#else
-#define TSEC_SIZE 0x01000
-#define TSEC_MDIO_OFFSET 0x01000
-#endif
-
-#define CONFIG_SYS_MDIO_BASE_ADDR (MDIO_BASE_ADDR + TSEC_MDIO_REGS_OFFSET)
-
-#define TSEC_GET_REGS(num, offset) \
- (struct tsec __iomem *)\
- (TSEC_BASE_ADDR + (((num) - 1) * (offset)))
-
-#define TSEC_GET_REGS_BASE(num) \
- TSEC_GET_REGS((num), TSEC_SIZE)
-
-#define TSEC_GET_MDIO_REGS(num, offset) \
- (struct tsec_mii_mng __iomem *)\
- (CONFIG_SYS_MDIO_BASE_ADDR + ((num) - 1) * (offset))
-
-#define TSEC_GET_MDIO_REGS_BASE(num) \
- TSEC_GET_MDIO_REGS((num), TSEC_MDIO_OFFSET)
-
-#define DEFAULT_MII_NAME "FSL_MDIO"
-
-#define STD_TSEC_INFO(num) \
-{ \
- .regs = TSEC_GET_REGS_BASE(num), \
- .miiregs_sgmii = TSEC_GET_MDIO_REGS_BASE(num), \
- .devname = CONFIG_TSEC##num##_NAME, \
- .phyaddr = TSEC##num##_PHY_ADDR, \
- .flags = TSEC##num##_FLAGS, \
- .mii_devname = DEFAULT_MII_NAME \
-}
-
-#define SET_STD_TSEC_INFO(x, num) \
-{ \
- x.regs = TSEC_GET_REGS_BASE(num); \
- x.miiregs_sgmii = TSEC_GET_MDIO_REGS_BASE(num); \
- x.devname = CONFIG_TSEC##num##_NAME; \
- x.phyaddr = TSEC##num##_PHY_ADDR; \
- x.flags = TSEC##num##_FLAGS;\
- x.mii_devname = DEFAULT_MII_NAME;\
-}
-
-#endif /* CONFIG_DM_ETH */
-
#define MAC_ADDR_LEN 6
/* #define TSEC_TIMEOUT 1000000 */
@@ -414,11 +364,7 @@
u32 flags;
uint rx_idx; /* index of the current RX buffer */
uint tx_idx; /* index of the current TX buffer */
-#ifndef CONFIG_DM_ETH
- struct eth_device *dev;
-#else
struct udevice *dev;
-#endif
};
struct tsec_info_struct {
@@ -431,10 +377,4 @@
u32 flags;
};
-#ifndef CONFIG_DM_ETH
-int tsec_standard_init(struct bd_info *bis);
-int tsec_eth_init(struct bd_info *bis, struct tsec_info_struct *tsec_info,
- int num);
-#endif
-
#endif /* __TSEC_H */