Blackfin: blackstamp: new board port
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
diff --git a/include/configs/blackstamp.h b/include/configs/blackstamp.h
new file mode 100644
index 0000000..f61e5b7
--- /dev/null
+++ b/include/configs/blackstamp.h
@@ -0,0 +1,275 @@
+/*
+ * U-boot - Configuration file for BlackStamp board
+ * Configuration by Ben Matthews for UR LLE using bf533-stamp.h
+ * as a template
+ * See http://blackfin.uclinux.org/gf/project/blackstamp/
+ */
+
+#ifndef __CONFIG_BLACKSTAMP_H__
+#define __CONFIG_BLACKSTAMP_H__
+
+#include <asm/blackfin-config-pre.h>
+
+/*
+ * Debugging: Set these options if you're having problems
+ */
+/*
+ * #define CONFIG_DEBUG_EARLY_SERIAL
+ * #define DEBUG
+ * #define CONFIG_DEBUG_DUMP
+ * #define CONFIG_DEBUG_DUMP_SYMS
+*/
+#define CONFIG_PANIC_HANG 0
+
+/* CPU Options
+ * Be sure to set the Silicon Revision Correctly
+ */
+#define CONFIG_BFIN_CPU bf532-0.5
+#define CONFIG_BFIN_BOOT_MODE BFIN_BOOT_SPI_MASTER
+
+/*
+ * Board settings
+ */
+#define CONFIG_DRIVER_SMC91111 1
+#define CONFIG_SMC91111_BASE 0x20300300
+
+/* FLASH/ETHERNET uses the same address range
+ * Depending on what you have the CPLD doing
+ * this probably isn't needed
+ */
+#define SHARED_RESOURCES 1
+
+/* Is I2C bit-banged? */
+#undef CONFIG_SOFT_I2
+
+/*
+ * Clock Settings
+ * CCLK = (CLKIN * VCO_MULT) / CCLK_DIV
+ * SCLK = (CLKIN * VCO_MULT) / SCLK_DIV
+ */
+/* CONFIG_CLKIN_HZ is any value in Hz */
+#define CONFIG_CLKIN_HZ 25000000
+/* CLKIN_HALF controls the DF bit in PLL_CTL 0 = CLKIN */
+/* 1 = CLKIN / 2 */
+#define CONFIG_CLKIN_HALF 0
+/* PLL_BYPASS controls the BYPASS bit in PLL_CTL 0 = do not bypass */
+/* 1 = bypass PLL */
+#define CONFIG_PLL_BYPASS 0
+/* VCO_MULT controls the MSEL (multiplier) bits in PLL_CTL */
+/* Values can range from 0-63 (where 0 means 64) */
+#define CONFIG_VCO_MULT 16
+/* CCLK_DIV controls the core clock divider */
+/* Values can be 1, 2, 4, or 8 ONLY */
+#define CONFIG_CCLK_DIV 1
+/* SCLK_DIV controls the system clock divider */
+/* Values can range from 1-15 */
+#define CONFIG_SCLK_DIV 3
+
+/*
+ * Network settings
+ */
+
+#ifdef CONFIG_DRIVER_SMC91111
+#define CONFIG_IPADDR 192.168.0.15
+#define CONFIG_NETMASK 255.255.255.0
+#define CONFIG_GATEWAYIP 192.168.0.1
+#define CONFIG_SERVERIP 192.168.0.2
+#define CONFIG_HOSTNAME blackstamp
+#define CONFIG_ROOTPATH /checkout/uClinux-dist/romfs
+#define CONFIG_SYS_AUTOLOAD "no"
+
+/* To remove hardcoding and enable MAC storage in EEPROM */
+/* #define CONFIG_ETHADDR 02:80:ad:20:31:b8 */
+#endif
+
+#define CONFIG_ENV_IS_IN_SPI_FLASH
+#define CONFIG_ENV_OFFSET 0x4000
+#define CONFIG_ENV_SIZE 0x2000
+#define CONFIG_ENV_SECT_SIZE 0x40000
+#define ENV_IS_EMBEDDED_CUSTOM
+
+/*
+ * SDRAM settings & memory map
+ */
+
+#define CONFIG_MEM_SIZE 64 /* 128, 64, 32, 16 */
+#define CONFIG_MEM_ADD_WDTH 10 /* 8, 9, 10, 11 */
+
+#define CONFIG_SYS_MONITOR_LEN (256 << 10)
+#define CONFIG_SYS_MALLOC_LEN (384 << 10)
+
+/*
+ * Command settings
+ */
+
+#define CONFIG_SYS_LONGHELP 1
+#define CONFIG_CMDLINE_EDITING 1
+#define CONFIG_AUTO_COMPLETE 1
+#define CONFIG_ENV_OVERWRITE 1
+
+#include <config_cmd_default.h>
+
+#ifdef CONFIG_DRIVER_SMC91111
+# define CONFIG_CMD_DHCP
+# define CONFIG_CMD_PING
+#else
+# undef CONFIG_CMD_NET
+#endif
+
+#ifdef CONFIG_SOFT_I2C
+# define CONFIG_CMD_I2C
+#endif
+
+#define CONFIG_CMD_BOOTLDR
+#define CONFIG_CMD_CACHE
+#define CONFIG_CMD_CPLBINFO
+#define CONFIG_CMD_DATE
+#define CONFIG_CMD_SF
+#define CONFIG_CMD_ELF
+
+#define CONFIG_BOOTDELAY 5
+#define CONFIG_BOOTCOMMAND "run ramboot"
+#define CONFIG_BOOTARGS \
+ "root=/dev/mtdblock0 rw " \
+ "clkin_hz=" MK_STR(CONFIG_CLKIN_HZ) " " \
+ "earlyprintk=" \
+ "serial," \
+ "uart" MK_STR(CONFIG_UART_CONSOLE) "," \
+ MK_STR(CONFIG_BAUDRATE) " " \
+ "console=ttyBF0," MK_STR(CONFIG_BAUDRATE)
+
+#if defined(CONFIG_CMD_NET)
+# if (CONFIG_BFIN_BOOT_MODE == BFIN_BOOT_BYPASS)
+# define UBOOT_ENV_FILE "u-boot.bin"
+# else
+# define UBOOT_ENV_FILE "u-boot.ldr"
+# endif
+# if (CONFIG_BFIN_BOOT_MODE == BFIN_BOOT_SPI_MASTER)
+# ifdef CONFIG_SPI
+# define UBOOT_ENV_UPDATE \
+ "eeprom write $(loadaddr) 0x0 $(filesize)"
+# else
+# define UBOOT_ENV_UPDATE \
+ "sf probe " MK_STR(BFIN_BOOT_SPI_SSEL) ";" \
+ "sf erase 0 0x40000;" \
+ "sf write $(loadaddr) 0 $(filesize)"
+# endif
+# else
+# define UBOOT_ENV_UPDATE \
+ "protect off 0x20000000 0x2003FFFF;" \
+ "erase 0x20000000 0x2003FFFF;" \
+ "cp.b $(loadaddr) 0x20000000 $(filesize)"
+# endif
+# define NETWORK_ENV_SETTINGS \
+ "ubootfile=" UBOOT_ENV_FILE "\0" \
+ "update=" \
+ "tftp $(loadaddr) $(ubootfile);" \
+ UBOOT_ENV_UPDATE \
+ "\0" \
+ "addip=set bootargs $(bootargs) " \
+ "ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask):" \
+ "$(hostname):eth0:off" \
+ "\0" \
+ "ramargs=set bootargs " CONFIG_BOOTARGS "\0" \
+ "ramboot=" \
+ "tftp $(loadaddr) uImage;" \
+ "run ramargs;" \
+ "run addip;" \
+ "bootm" \
+ "\0" \
+ "nfsargs=set bootargs " \
+ "root=/dev/nfs rw " \
+ "nfsroot=$(serverip):$(rootpath),tcp,nfsvers=3" \
+ "\0" \
+ "nfsboot=" \
+ "tftp $(loadaddr) vmImage;" \
+ "run nfsargs;" \
+ "run addip;" \
+ "bootm" \
+ "\0"
+#else
+# define NETWORK_ENV_SETTINGS
+#endif
+
+/*
+ * Console settings
+ */
+#define CONFIG_BAUDRATE 57600
+#define CONFIG_LOADS_ECHO 1
+#define CONFIG_UART_CONSOLE 0
+
+/*
+ * I2C settings
+ * By default PF2 is used as SDA and PF3 as SCL on the Stamp board
+ * Located on the expansion connector on pins 86/85
+ * Note these pins are arbitrarily chosen because we aren't using
+ * them yet. You can (and probably should) change these values!
+ */
+#ifdef CONFIG_SOFT_I2C
+
+#define PF_SCL PF9
+#define PF_SDA PF8
+
+#define I2C_INIT do { *pFIO_DIR |= PF_SCL; SSYNC(); } while (0)
+#define I2C_ACTIVE do { *pFIO_DIR |= PF_SDA; *pFIO_INEN &= ~PF_SDA; SSYNC(); } while (0)
+#define I2C_TRISTATE do { *pFIO_DIR &= ~PF_SDA; *pFIO_INEN |= PF_SDA; SSYNC(); } while (0)
+#define I2C_READ ((*pFIO_FLAG_D & PF_SDA) != 0)
+#define I2C_SDA(bit) \
+ do { \
+ if (bit) \
+ *pFIO_FLAG_S = PF_SDA; \
+ else \
+ *pFIO_FLAG_C = PF_SDA; \
+ SSYNC(); \
+ } while (0)
+#define I2C_SCL(bit) \
+ do { \
+ if (bit) \
+ *pFIO_FLAG_S = PF_SCL; \
+ else \
+ *pFIO_FLAG_C = PF_SCL; \
+ SSYNC(); \
+ } while (0)
+#define I2C_DELAY udelay(5) /* 1/4 I2C clock duration */
+
+#define CONFIG_SYS_I2C_SPEED 50000
+#define CONFIG_SYS_I2C_SLAVE 0xFE
+#endif
+
+/*
+ * Miscellaneous configurable options
+ */
+#define CONFIG_RTC_BFIN 1
+
+/*
+ * Serial Flash Infomation
+ */
+#define CONFIG_BFIN_SPI
+/* For the M25P64 SCK Should be Kept < 20Mhz */
+#define CONFIG_ENV_SPI_MAX_HZ 20000000
+#define CONFIG_SF_DEFAULT_HZ 20000000
+#define CONFIG_SPI_FLASH
+#define CONFIG_SPI_FLASH_STMICRO
+
+/*
+ * FLASH organization and environment definitions
+ */
+
+#define CONFIG_EBIU_AMGCTL_VAL 0xFF
+#define CONFIG_EBIU_AMBCTL0_VAL 0xBBC3BBC3
+#define CONFIG_EBIU_AMBCTL1_VAL 0x99B39983
+#define CONFIG_EBIU_SDRRC_VAL 0x268
+#define CONFIG_EBIU_SDGCTL_VAL 0x911109
+
+/* Even though Rev C boards have Parallel Flash
+ * We aren't supporting it. Newer versions of the
+ * hardware don't support Parallel Flash at all.
+ */
+#define CONFIG_SYS_NO_FLASH
+#undef CONFIG_CMD_IMLS
+#undef CONFIG_CMD_JFFS2
+#undef CONFIG_CMD_FLASH
+
+#include <asm/blackfin-config-post.h>
+
+#endif