board: ge: ppd: Enable CONFIG_DM_MMC
Use MMC device model, and remove USDHC pin configuration code since the
pinctrl driver is used.
Signed-off-by: Ian Ray <ian.ray@ge.com>
diff --git a/arch/arm/dts/imx53-ppd.dts b/arch/arm/dts/imx53-ppd.dts
index 98e7dad..f89d6f4 100644
--- a/arch/arm/dts/imx53-ppd.dts
+++ b/arch/arm/dts/imx53-ppd.dts
@@ -12,3 +12,32 @@
model = "General Electric CS ONE";
compatible = "ge,imx53-cpuvo", "fsl,imx53";
};
+
+&iomuxc {
+ pinctrl-names = "default";
+
+ pinctrl_esdhc3: esdhc3grp {
+ fsl,pins = <
+ MX53_PAD_PATA_DATA8__ESDHC3_DAT0 0x1d5
+ MX53_PAD_PATA_DATA9__ESDHC3_DAT1 0x1d5
+ MX53_PAD_PATA_DATA10__ESDHC3_DAT2 0x1d5
+ MX53_PAD_PATA_DATA11__ESDHC3_DAT3 0x1d5
+ MX53_PAD_PATA_DATA0__ESDHC3_DAT4 0x1d5
+ MX53_PAD_PATA_DATA1__ESDHC3_DAT5 0x1d5
+ MX53_PAD_PATA_DATA2__ESDHC3_DAT6 0x1d5
+ MX53_PAD_PATA_DATA3__ESDHC3_DAT7 0x1d5
+ MX53_PAD_PATA_RESET_B__ESDHC3_CMD 0x1d5
+ MX53_PAD_PATA_IORDY__ESDHC3_CLK 0x1d5
+ >;
+ };
+};
+
+/* eMMC */
+&esdhc3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_esdhc3>;
+ compatible = "fsl,esdhc";
+ bus-width = <8>;
+ non-removable;
+ status = "okay";
+};
diff --git a/board/ge/mx53ppd/mx53ppd.c b/board/ge/mx53ppd/mx53ppd.c
index 23bfe55..9e13a24 100644
--- a/board/ge/mx53ppd/mx53ppd.c
+++ b/board/ge/mx53ppd/mx53ppd.c
@@ -122,79 +122,6 @@
imx_iomux_v3_setup_multiple_pads(fec_pads, ARRAY_SIZE(fec_pads));
}
-#ifdef CONFIG_FSL_ESDHC
-struct fsl_esdhc_cfg esdhc_cfg[2] = {
- {MMC_SDHC3_BASE_ADDR},
- {MMC_SDHC1_BASE_ADDR},
-};
-
-int board_mmc_getcd(struct mmc *mmc)
-{
- return 1;
-}
-
-#define SD_CMD_PAD_CTRL (PAD_CTL_HYS | PAD_CTL_DSE_HIGH | \
- PAD_CTL_PUS_100K_UP)
-#define SD_PAD_CTRL (PAD_CTL_HYS | PAD_CTL_PUS_47K_UP | \
- PAD_CTL_DSE_HIGH)
-
-int board_mmc_init(bd_t *bis)
-{
- static const iomux_v3_cfg_t sd1_pads[] = {
- NEW_PAD_CTRL(MX53_PAD_PATA_RESET_B__ESDHC3_CMD,
- SD_CMD_PAD_CTRL),
- NEW_PAD_CTRL(MX53_PAD_PATA_IORDY__ESDHC3_CLK, SD_PAD_CTRL),
- NEW_PAD_CTRL(MX53_PAD_PATA_DATA8__ESDHC3_DAT0, SD_PAD_CTRL),
- NEW_PAD_CTRL(MX53_PAD_PATA_DATA9__ESDHC3_DAT1, SD_PAD_CTRL),
- NEW_PAD_CTRL(MX53_PAD_PATA_DATA10__ESDHC3_DAT2, SD_PAD_CTRL),
- NEW_PAD_CTRL(MX53_PAD_PATA_DATA11__ESDHC3_DAT3, SD_PAD_CTRL),
- NEW_PAD_CTRL(MX53_PAD_PATA_DATA0__ESDHC3_DAT4, SD_PAD_CTRL),
- NEW_PAD_CTRL(MX53_PAD_PATA_DATA1__ESDHC3_DAT5, SD_PAD_CTRL),
- NEW_PAD_CTRL(MX53_PAD_PATA_DATA2__ESDHC3_DAT6, SD_PAD_CTRL),
- NEW_PAD_CTRL(MX53_PAD_PATA_DATA3__ESDHC3_DAT7, SD_PAD_CTRL),
- MX53_PAD_EIM_DA11__GPIO3_11,
- };
-
- static const iomux_v3_cfg_t sd2_pads[] = {
- NEW_PAD_CTRL(MX53_PAD_SD1_CMD__ESDHC1_CMD, SD_CMD_PAD_CTRL),
- NEW_PAD_CTRL(MX53_PAD_SD1_CLK__ESDHC1_CLK, SD_PAD_CTRL),
- NEW_PAD_CTRL(MX53_PAD_SD1_DATA0__ESDHC1_DAT0, SD_PAD_CTRL),
- NEW_PAD_CTRL(MX53_PAD_SD1_DATA1__ESDHC1_DAT1, SD_PAD_CTRL),
- NEW_PAD_CTRL(MX53_PAD_SD1_DATA2__ESDHC1_DAT2, SD_PAD_CTRL),
- NEW_PAD_CTRL(MX53_PAD_SD1_DATA3__ESDHC1_DAT3, SD_PAD_CTRL),
- MX53_PAD_EIM_DA13__GPIO3_13,
- };
-
- u32 index;
- int ret;
-
- esdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC3_CLK);
- esdhc_cfg[1].sdhc_clk = mxc_get_clock(MXC_ESDHC_CLK);
-
- for (index = 0; index < CONFIG_SYS_FSL_ESDHC_NUM; index++) {
- switch (index) {
- case 0:
- imx_iomux_v3_setup_multiple_pads(sd1_pads,
- ARRAY_SIZE(sd1_pads));
- break;
- case 1:
- imx_iomux_v3_setup_multiple_pads(sd2_pads,
- ARRAY_SIZE(sd2_pads));
- break;
- default:
- printf("Warning: you configured more ESDHC controller (%d) as supported by the board(2)\n",
- CONFIG_SYS_FSL_ESDHC_NUM);
- return -EINVAL;
- }
- ret = fsl_esdhc_initialize(bis, &esdhc_cfg[index]);
- if (ret)
- return ret;
- }
-
- return 0;
-}
-#endif
-
#define I2C_PAD_CTRL (PAD_CTL_SRE_FAST | PAD_CTL_DSE_HIGH | \
PAD_CTL_PUS_100K_UP | PAD_CTL_ODE)
diff --git a/configs/mx53ppd_defconfig b/configs/mx53ppd_defconfig
index 04537c5..ec3bc10 100644
--- a/configs/mx53ppd_defconfig
+++ b/configs/mx53ppd_defconfig
@@ -46,3 +46,7 @@
CONFIG_CMD_DM=y
CONFIG_OF_CONTROL=y
CONFIG_DEFAULT_DEVICE_TREE="imx53-ppd"
+CONFIG_DM_MMC=y
+CONFIG_BLK=y
+CONFIG_PINCTRL=y
+CONFIG_PINCTRL_IMX5=y
diff --git a/include/configs/mx53ppd.h b/include/configs/mx53ppd.h
index d2a8e65..db6cd65 100644
--- a/include/configs/mx53ppd.h
+++ b/include/configs/mx53ppd.h
@@ -30,10 +30,6 @@
#define CONFIG_MXC_UART
#define CONFIG_MXC_UART_BASE UART1_BASE
-/* MMC Configs */
-#define CONFIG_SYS_FSL_ESDHC_ADDR 0
-#define CONFIG_SYS_FSL_ESDHC_NUM 2
-
/* Eth Configs */
#define CONFIG_FEC_MXC
@@ -101,7 +97,7 @@
"image=/boot/fitImage\0" \
"fdt_high=0xffffffff\0" \
"dev=mmc\0" \
- "devnum=0\0" \
+ "devnum=2\0" \
"rootdev=mmcblk0p\0" \
"quiet=quiet loglevel=0\0" \
"console=" CONSOLE_DEV "\0" \