arm: mvebu: Better align Clearfog dts file with Linux kernel

This makes changes so the u-boot dts file is structured more
similar to the mainline linux dtsi file.  It provides a minimal
common dts that can work for most boards based on the ClearFog
platform.  Ethernet support is only supported for eth0 however
all devices are left enabled so u-boot can generate and
provide mac addresses for all of the network interfaces.

Signed-off-by: Jon Nettleton <jon@solid-run.com>
[baruch: rebase on recent changes]
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Dennis Gilmore <dennis@ausil.us>
Tested-by: Dennis Gilmore <dennis@ausil.us>
Signed-off-by: Stefan Roese <sr@denx.de>
diff --git a/arch/arm/dts/armada-388-clearfog.dts b/arch/arm/dts/armada-388-clearfog.dts
index 1403600..16a47d5 100644
--- a/arch/arm/dts/armada-388-clearfog.dts
+++ b/arch/arm/dts/armada-388-clearfog.dts
@@ -81,174 +81,6 @@
 
 	soc {
 		internal-regs {
-			ethernet@30000 {
-				mac-address = [00 50 43 02 02 02];
-				phy-mode = "sgmii";
-				status = "okay";
-
-				fixed-link {
-					speed = <1000>;
-					full-duplex;
-				};
-			};
-
-			ethernet@34000 {
-				mac-address = [00 50 43 02 02 03];
-				managed = "in-band-status";
-				phy-mode = "sgmii";
-				status = "okay";
-			};
-
-			i2c@11000 {
-				/* Is there anything on this? */
-				clock-frequency = <100000>;
-				pinctrl-0 = <&i2c0_pins>;
-				pinctrl-names = "default";
-				status = "okay";
-
-				/*
-				 * PCA9655 GPIO expander, up to 1MHz clock.
-				 *  0-CON3 CLKREQ#
-				 *  1-CON3 PERST#
-				 *  2-CON2 PERST#
-				 *  3-CON3 W_DISABLE
-				 *  4-CON2 CLKREQ#
-				 *  5-USB3 overcurrent
-				 *  6-USB3 power
-				 *  7-CON2 W_DISABLE
-				 *  8-JP4 P1
-				 *  9-JP4 P4
-				 * 10-JP4 P5
-				 * 11-m.2 DEVSLP
-				 * 12-SFP_LOS
-				 * 13-SFP_TX_FAULT
-				 * 14-SFP_TX_DISABLE
-				 * 15-SFP_MOD_DEF0
-				 */
-				expander0: gpio-expander@20 {
-					/*
-					 * This is how it should be:
-					 * compatible = "onnn,pca9655",
-					 *	 "nxp,pca9555";
-					 * but you can't do this because of
-					 * the way I2C works.
-					 */
-					compatible = "nxp,pca9555";
-					gpio-controller;
-					#gpio-cells = <2>;
-					reg = <0x20>;
-
-					pcie1_0_clkreq {
-						gpio-hog;
-						gpios = <0 GPIO_ACTIVE_LOW>;
-						input;
-						line-name = "pcie1.0-clkreq";
-					};
-					pcie1_0_w_disable {
-						gpio-hog;
-						gpios = <3 GPIO_ACTIVE_LOW>;
-						output-low;
-						line-name = "pcie1.0-w-disable";
-					};
-					pcie2_0_clkreq {
-						gpio-hog;
-						gpios = <4 GPIO_ACTIVE_LOW>;
-						input;
-						line-name = "pcie2.0-clkreq";
-					};
-					pcie2_0_w_disable {
-						gpio-hog;
-						gpios = <7 GPIO_ACTIVE_LOW>;
-						output-low;
-						line-name = "pcie2.0-w-disable";
-					};
-					usb3_ilimit {
-						gpio-hog;
-						gpios = <5 GPIO_ACTIVE_LOW>;
-						input;
-						line-name = "usb3-current-limit";
-					};
-					usb3_power {
-						gpio-hog;
-						gpios = <6 GPIO_ACTIVE_HIGH>;
-						output-high;
-						line-name = "usb3-power";
-					};
-					m2_devslp {
-						gpio-hog;
-						gpios = <11 GPIO_ACTIVE_HIGH>;
-						output-low;
-						line-name = "m.2 devslp";
-					};
-				};
-
-				/* The MCP3021 is 100kHz clock only */
-				mikrobus_adc: mcp3021@4c {
-					compatible = "microchip,mcp3021";
-					reg = <0x4c>;
-				};
-
-				/* Also something at 0x64 */
-			};
-
-			i2c@11100 {
-				/*
-				 * Routed to SFP, mikrobus, and PCIe.
-				 * SFP limits this to 100kHz, and requires
-				 *  an AT24C01A/02/04 with address pins tied
-				 *  low, which takes addresses 0x50 and 0x51.
-				 * Mikrobus doesn't specify beyond an I2C
-				 *  bus being present.
-				 * PCIe uses ARP to assign addresses, or
-				 *  0x63-0x64.
-				 */
-				clock-frequency = <100000>;
-				pinctrl-0 = <&clearfog_i2c1_pins>;
-				pinctrl-names = "default";
-				status = "okay";
-			};
-
-			pinctrl@18000 {
-				clearfog_dsa0_clk_pins: clearfog-dsa0-clk-pins {
-					marvell,pins = "mpp46";
-					marvell,function = "ref";
-				};
-				clearfog_dsa0_pins: clearfog-dsa0-pins {
-					marvell,pins = "mpp23", "mpp41";
-					marvell,function = "gpio";
-				};
-				clearfog_i2c1_pins: i2c1-pins {
-					/* SFP, PCIe, mSATA, mikrobus */
-					marvell,pins = "mpp26", "mpp27";
-					marvell,function = "i2c1";
-				};
-				clearfog_sdhci_cd_pins: clearfog-sdhci-cd-pins {
-					marvell,pins = "mpp20";
-					marvell,function = "gpio";
-				};
-				clearfog_spi1_cs_pins: spi1-cs-pins {
-					marvell,pins = "mpp55";
-					marvell,function = "spi1";
-				};
-				mikro_pins: mikro-pins {
-					/* int: mpp22 rst: mpp29 */
-					marvell,pins = "mpp22", "mpp29";
-					marvell,function = "gpio";
-				};
-				mikro_spi_pins: mikro-spi-pins {
-					marvell,pins = "mpp43";
-					marvell,function = "spi1";
-				};
-				mikro_uart_pins: mikro-uart-pins {
-					marvell,pins = "mpp24", "mpp25";
-					marvell,function = "ua1";
-				};
-				rear_button_pins: rear-button-pins {
-					marvell,pins = "mpp34";
-					marvell,function = "gpio";
-				};
-			};
-
 			rtc@a3800 {
 				/*
 				 * If the rtc doesn't work, run "date reset"
@@ -297,7 +129,8 @@
 				status = "okay";
 			};
 
-			usb3@f8000 {
+			usb0: usb3@f8000 {
+				/* CON7, USB-A port on back of device */
 				status = "okay";
 			};
 		};
@@ -321,72 +154,6 @@
 		};
 	};
 
-	sfp: sfp {
-		compatible = "sff,sfp";
-		i2c-bus = <&i2c1>;
-		los-gpio = <&expander0 12 GPIO_ACTIVE_HIGH>;
-		moddef0-gpio = <&expander0 15 GPIO_ACTIVE_LOW>;
-		sfp,ethernet = <&eth2>;
-		tx-disable-gpio = <&expander0 14 GPIO_ACTIVE_HIGH>;
-		tx-fault-gpio = <&expander0 13 GPIO_ACTIVE_HIGH>;
-	};
-
-	dsa@0 {
-		compatible = "marvell,dsa";
-		dsa,ethernet = <&eth1>;
-		dsa,mii-bus = <&mdio>;
-		pinctrl-0 = <&clearfog_dsa0_clk_pins &clearfog_dsa0_pins>;
-		pinctrl-names = "default";
-		#address-cells = <2>;
-		#size-cells = <0>;
-
-		switch@0 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			reg = <4 0>;
-
-			port@0 {
-				reg = <0>;
-				label = "lan1";
-			};
-
-			port@1 {
-				reg = <1>;
-				label = "lan2";
-			};
-
-			port@2 {
-				reg = <2>;
-				label = "lan3";
-			};
-
-			port@3 {
-				reg = <3>;
-				label = "lan4";
-			};
-
-			port@4 {
-				reg = <4>;
-				label = "lan5";
-			};
-
-			port@5 {
-				reg = <5>;
-				label = "cpu";
-			};
-
-			port@6 {
-				/* 88E1512 external phy */
-				reg = <6>;
-				label = "lan6";
-				fixed-link {
-					speed = <1000>;
-					full-duplex;
-				};
-			};
-		};
-	};
-
 	gpio-keys {
 		compatible = "gpio-keys";
 		pinctrl-0 = <&rear_button_pins>;
@@ -406,6 +173,155 @@
 	status = "okay";
 };
 
+&eth1 {
+	managed = "in-band-status";
+	phy-mode = "sgmii";
+	status = "okay";
+};
+
+&eth2 {
+	phy-mode = "sgmii";
+	status = "okay";
+};
+
+&i2c0 {
+	clock-frequency = <400000>;
+	pinctrl-0 = <&i2c0_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+
+	/*
+	 * PCA9655 GPIO expander, up to 1MHz clock.
+	 *  0-CON3 CLKREQ#
+	 *  1-CON3 PERST#
+	 *  2-CON2 PERST#
+	 *  3-CON3 W_DISABLE
+	 *  4-CON2 CLKREQ#
+	 *  5-USB3 overcurrent
+	 *  6-USB3 power
+	 *  7-CON2 W_DISABLE
+	 *  8-JP4 P1
+	 *  9-JP4 P4
+	 * 10-JP4 P5
+	 * 11-m.2 DEVSLP
+	 * 12-SFP_LOS
+	 * 13-SFP_TX_FAULT
+	 * 14-SFP_TX_DISABLE
+	 * 15-SFP_MOD_DEF0
+	 */
+	expander0: gpio-expander@20 {
+		/*
+		 * This is how it should be:
+		 * compatible = "onnn,pca9655",
+		 *	 "nxp,pca9555";
+		 * but you can't do this because of
+		 * the way I2C works.
+		 */
+		compatible = "nxp,pca9555";
+		gpio-controller;
+		#gpio-cells = <2>;
+		reg = <0x20>;
+
+		pcie1_0_clkreq {
+			gpio-hog;
+			gpios = <0 GPIO_ACTIVE_LOW>;
+			input;
+			line-name = "pcie1.0-clkreq";
+		};
+		pcie1_0_w_disable {
+			gpio-hog;
+			gpios = <3 GPIO_ACTIVE_LOW>;
+			output-low;
+			line-name = "pcie1.0-w-disable";
+		};
+		pcie2_0_clkreq {
+			gpio-hog;
+			gpios = <4 GPIO_ACTIVE_LOW>;
+			input;
+			line-name = "pcie2.0-clkreq";
+		};
+		pcie2_0_w_disable {
+			gpio-hog;
+			gpios = <7 GPIO_ACTIVE_LOW>;
+			output-low;
+			line-name = "pcie2.0-w-disable";
+		};
+		usb3_ilimit {
+			gpio-hog;
+			gpios = <5 GPIO_ACTIVE_LOW>;
+			input;
+			line-name = "usb3-current-limit";
+		};
+		usb3_power {
+			gpio-hog;
+			gpios = <6 GPIO_ACTIVE_HIGH>;
+			output-high;
+			line-name = "usb3-power";
+		};
+		m2_devslp {
+			gpio-hog;
+			gpios = <11 GPIO_ACTIVE_HIGH>;
+			output-low;
+			line-name = "m.2 devslp";
+		};
+	};
+
+	mikrobus_adc: mcp3021@4c {
+		compatible = "microchip,mcp3021";
+		reg = <0x4c>;
+	};
+};
+
+&i2c1 {
+	/*
+	 * Routed to SFP, mikrobus, and PCIe.
+	 * SFP limits this to 100kHz, and requires
+	 *  an AT24C01A/02/04 with address pins tied
+	 *  low, which takes addresses 0x50 and 0x51.
+	 * Mikrobus doesn't specify beyond an I2C
+	 *  bus being present.
+	 * PCIe uses ARP to assign addresses, or
+	 *  0x63-0x64.
+	 */
+	clock-frequency = <100000>;
+	pinctrl-0 = <&clearfog_i2c1_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
+&pinctrl {
+	clearfog_i2c1_pins: i2c1-pins {
+		/* SFP, PCIe, mSATA, mikrobus */
+		marvell,pins = "mpp26", "mpp27";
+		marvell,function = "i2c1";
+	};
+	clearfog_sdhci_cd_pins: clearfog-sdhci-cd-pins {
+		marvell,pins = "mpp20";
+		marvell,function = "gpio";
+	};
+	clearfog_spi1_cs_pins: spi1-cs-pins {
+		marvell,pins = "mpp55";
+		marvell,function = "spi1";
+	};
+	mikro_pins: mikro-pins {
+		/* int: mpp22 rst: mpp29 */
+		marvell,pins = "mpp22", "mpp29";
+		marvell,function = "gpio";
+	};
+	mikro_spi_pins: mikro-spi-pins {
+		marvell,pins = "mpp43";
+		marvell,function = "spi1";
+	};
+	mikro_uart_pins: mikro-uart-pins {
+		marvell,pins = "mpp24", "mpp25";
+		marvell,function = "ua1";
+	};
+	rear_button_pins: rear-button-pins {
+		marvell,pins = "mpp34";
+		marvell,function = "gpio";
+	};
+};
+
 /*
 +#define A38x_CUSTOMER_BOARD_1_MPP16_23         0x00400011
 MPP18: gpio		? (pca9655 int?)