sunxi: Add defconfig and dts file for inet86dz board
The inet86dz board is a board used in 7" tablets from various oems.
These tablets are a23 based 7" tablets featuring a 1024x600 LCD,
512MB RAM, 4G NAND, rtl8188etv usb wifi, gsl1680 touchschreen,
micro-sd slot, 3.5mm headphone jack and a micro-usb otg connector
which doubles as charging port.
The dts file this commit adds is identical to the one submitted to
the upstream kernel.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
index 5172a7e..de75e24 100644
--- a/arch/arm/dts/Makefile
+++ b/arch/arm/dts/Makefile
@@ -223,6 +223,7 @@
dtb-$(CONFIG_MACH_SUN8I_A23) += \
sun8i-a23-evb.dtb \
sun8i-a23-gt90h-v4.dtb \
+ sun8i-a23-inet86dz.dtb \
sun8i-a23-polaroid-mid2407pxe03.dtb \
sun8i-a23-polaroid-mid2809pxe04.dtb \
sun8i-a23-q8-tablet.dtb
diff --git a/arch/arm/dts/sun8i-a23-inet86dz.dts b/arch/arm/dts/sun8i-a23-inet86dz.dts
new file mode 100644
index 0000000..0405258
--- /dev/null
+++ b/arch/arm/dts/sun8i-a23-inet86dz.dts
@@ -0,0 +1,293 @@
+/*
+ * Copyright 2016 Hans de Goede <hdegoede@redhat.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "sun8i-a23.dtsi"
+#include "sunxi-common-regulators.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/pinctrl/sun4i-a10.h>
+#include <dt-bindings/pwm/pwm.h>
+
+/ {
+ model = "INet-86DZ Rev 01";
+ compatible = "primux,inet86dz", "allwinner,sun8i-a23";
+
+ aliases {
+ serial0 = &r_uart;
+ };
+
+ backlight: backlight {
+ compatible = "pwm-backlight";
+ pinctrl-names = "default";
+ pinctrl-0 = <&bl_en_pin_inet86dz>;
+ pwms = <&pwm 0 50000 PWM_POLARITY_INVERTED>;
+ brightness-levels = <0 10 20 30 40 50 60 70 80 90 100>;
+ default-brightness-level = <8>;
+ enable-gpios = <&pio 7 6 GPIO_ACTIVE_HIGH>; /* PH6 */
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+};
+
+&ehci0 {
+ status = "okay";
+};
+
+&i2c0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c0_pins_a>;
+ status = "okay";
+ /*
+ * The gsl1680 is rated at 400KHz and it will not work reliable at
+ * 100KHz, this has been confirmed on multiple different tablets.
+ * The gsl1680 is the only device on this bus.
+ */
+ clock-frequency = <400000>;
+
+ gsl1680: touchscreen@40 {
+ compatible = "silead,gsl1680";
+ reg = <0x40>;
+ interrupt-parent = <&pio>;
+ interrupts = <1 5 IRQ_TYPE_EDGE_FALLING>; /* PB5 */
+ pinctrl-names = "default";
+ pinctrl-0 = <&ts_power_pin_inet86dz>;
+ power-gpios = <&pio 7 1 GPIO_ACTIVE_HIGH>; /* PH1 */
+ touchscreen-size-x = <960>;
+ touchscreen-size-y = <640>;
+ touchscreen-max-fingers = <5>;
+ touchscreen-fw-name = "silead/gsl1680-inet86dz.fw";
+ };
+};
+
+&i2c1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c1_pins_a>;
+ status = "okay";
+};
+
+&lradc {
+ vref-supply = <®_vcc3v0>;
+ status = "okay";
+
+ button@200 {
+ label = "Volume Up";
+ linux,code = <KEY_VOLUMEUP>;
+ channel = <0>;
+ voltage = <200000>;
+ };
+
+ button@400 {
+ label = "Volume Down";
+ linux,code = <KEY_VOLUMEDOWN>;
+ channel = <0>;
+ voltage = <400000>;
+ };
+};
+
+&mmc0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_inet86dz>;
+ vmmc-supply = <®_dcdc1>;
+ bus-width = <4>;
+ cd-gpios = <&pio 1 4 GPIO_ACTIVE_HIGH>; /* PB4 */
+ cd-inverted;
+ status = "okay";
+};
+
+&pio {
+ bl_en_pin_inet86dz: bl_en_pin@0 {
+ allwinner,pins = "PH6";
+ allwinner,function = "gpio_in";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
+ mmc0_cd_pin_inet86dz: mmc0_cd_pin@0 {
+ allwinner,pins = "PB4";
+ allwinner,function = "gpio_in";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+ };
+
+ ts_power_pin_inet86dz: ts_power_pin@0 {
+ allwinner,pins = "PH1";
+ allwinner,function = "gpio_out";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
+ usb0_id_detect_pin: usb0_id_detect_pin@0 {
+ allwinner,pins = "PH8";
+ allwinner,function = "gpio_in";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+ };
+};
+
+&pwm {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pwm0_pins>;
+ status = "okay";
+};
+
+&r_rsb {
+ status = "okay";
+
+ axp22x: pmic@3a3 {
+ compatible = "x-powers,axp223";
+ reg = <0x3a3>;
+ interrupt-parent = <&nmi_intc>;
+ interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+ eldoin-supply = <®_dcdc1>;
+ x-powers,drive-vbus-en;
+ };
+};
+
+&r_uart {
+ pinctrl-names = "default";
+ pinctrl-0 = <&r_uart_pins_a>;
+ status = "okay";
+};
+
+#include "axp22x.dtsi"
+
+®_aldo1 {
+ regulator-always-on;
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-name = "vcc-io";
+};
+
+®_aldo2 {
+ regulator-always-on;
+ regulator-min-microvolt = <2350000>;
+ regulator-max-microvolt = <2650000>;
+ regulator-name = "vdd-dll";
+};
+
+®_aldo3 {
+ regulator-always-on;
+ regulator-min-microvolt = <2700000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-pll-avcc";
+};
+
+®_dc1sw {
+ regulator-name = "vcc-lcd";
+};
+
+®_dc5ldo {
+ regulator-always-on;
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <1400000>;
+ regulator-name = "vdd-cpus";
+};
+
+®_dcdc1 {
+ regulator-always-on;
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-name = "vcc-3v0";
+};
+
+®_dcdc2 {
+ regulator-always-on;
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <1400000>;
+ regulator-name = "vdd-sys";
+};
+
+®_dcdc3 {
+ regulator-always-on;
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <1400000>;
+ regulator-name = "vdd-cpu";
+};
+
+®_dcdc5 {
+ regulator-always-on;
+ regulator-min-microvolt = <1500000>;
+ regulator-max-microvolt = <1500000>;
+ regulator-name = "vcc-dram";
+};
+
+®_dldo1 {
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-wifi";
+};
+
+®_drivevbus {
+ regulator-name = "usb0-vbus";
+ status = "okay";
+};
+
+®_rtc_ldo {
+ regulator-name = "vcc-rtc";
+};
+
+&simplefb_lcd {
+ vcc-lcd-supply = <®_dc1sw>;
+};
+
+&usb_otg {
+ dr_mode = "otg";
+ status = "okay";
+};
+
+&usb_power_supply {
+ status = "okay";
+};
+
+&usbphy {
+ pinctrl-names = "default";
+ pinctrl-0 = <&usb0_id_detect_pin>;
+ usb0_id_det-gpio = <&pio 7 8 GPIO_ACTIVE_HIGH>; /* PH8 */
+ usb0_vbus_power-supply = <&usb_power_supply>;
+ usb0_vbus-supply = <®_drivevbus>;
+ usb1_vbus-supply = <®_dldo1>;
+ status = "okay";
+};
diff --git a/board/sunxi/MAINTAINERS b/board/sunxi/MAINTAINERS
index 4f8d950..de5207e 100644
--- a/board/sunxi/MAINTAINERS
+++ b/board/sunxi/MAINTAINERS
@@ -54,6 +54,7 @@
F: include/configs/sun8i.h
F: configs/ga10h_v1_1_defconfig
F: configs/gt90h_v4_defconfig
+F: configs/inet86dz_defconfig
F: configs/orangepi_2_defconfig
F: configs/orangepi_one_defconfig
F: configs/orangepi_pc_defconfig
diff --git a/configs/inet86dz_defconfig b/configs/inet86dz_defconfig
new file mode 100644
index 0000000..55768ba
--- /dev/null
+++ b/configs/inet86dz_defconfig
@@ -0,0 +1,24 @@
+CONFIG_ARM=y
+CONFIG_ARCH_SUNXI=y
+CONFIG_MACH_SUN8I_A23=y
+CONFIG_DRAM_CLK=552
+CONFIG_DRAM_ZQ=63351
+CONFIG_MMC0_CD_PIN="PB4"
+CONFIG_USB0_VBUS_PIN="AXP0-VBUS-ENABLE"
+CONFIG_USB0_VBUS_DET="AXP0-VBUS-DETECT"
+CONFIG_USB0_ID_DET="PH8"
+CONFIG_AXP_GPIO=y
+CONFIG_VIDEO_LCD_MODE="x:1024,y:600,depth:18,pclk_khz:51000,le:138,ri:162,up:22,lo:10,hs:20,vs:3,sync:3,vmode:0"
+CONFIG_VIDEO_LCD_DCLK_PHASE=0
+CONFIG_VIDEO_LCD_POWER="PH7"
+CONFIG_VIDEO_LCD_BL_EN="PH6"
+CONFIG_VIDEO_LCD_BL_PWM="PH0"
+CONFIG_DEFAULT_DEVICE_TREE="sun8i-a23-inet86dz"
+# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
+CONFIG_SPL=y
+CONFIG_SYS_EXTRA_OPTIONS="CONS_INDEX=5"
+# CONFIG_CMD_IMLS is not set
+# CONFIG_CMD_FLASH is not set
+# CONFIG_CMD_FPGA is not set
+CONFIG_AXP_DLDO1_VOLT=3300
+CONFIG_USB_MUSB_HOST=y