board: ti: am571x-idk: Support 6 port Ethernet or 4 port Ethernet with LCD
The board can support either ICSS1 Ethernet ports or LCD
based on J51 jumper. Factory default is ICSS1 Ethernet ports
(i.e. Jumper not populated).
Use the GPIO to detect the jumper setting and configure the
pinmux accordingly. Also select the right DT blob based on
the chosen configuration.
J51 absent -> ICSS1 Ethernet, no LCD on VOUT -> am571x-idk.dtb
J51 present -> LCD on VOUT, no ICSS1 Ethernet -> am571x-idk-lcd-osd.dtb
At present we only support the assume it is the Legacy LCD.
LCD detection mechanism needs to be added later to differentiate
between legacy vs new LCD.
For ICSS1 Ethernet pins use the following convention to set the pinmux
as PMT data is not yet finalized.
- If pin is output, set as PIN_OUTPUT
- If pin is input and external pull resistor present set as PIN_INPUT
- If pin is input and external pull resistor absent, set pull to same
as that of the external PHY's internall pull.
- Do not use SLEW_CONTROLon any pin.
Cc: Nishanth Menon <nm@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
diff --git a/board/ti/am57xx/mux_data.h b/board/ti/am57xx/mux_data.h
index 2f5243e..ff0e517 100644
--- a/board/ti/am57xx/mux_data.h
+++ b/board/ti/am57xx/mux_data.h
@@ -549,13 +549,6 @@
{VIN2A_D0, (M11 | PIN_INPUT_PULLDOWN)}, /* vin2a_d0.pr1_uart0_rxd */
{VIN2A_D1, (M11 | PIN_INPUT_PULLDOWN)}, /* vin2a_d1.pr1_uart0_txd */
{VIN2A_D2, (M10 | PIN_INPUT_PULLDOWN)}, /* vin2a_d2.eCAP1_in_PWM1_out */
- {VIN2A_D3, (M11 | PIN_INPUT_PULLDOWN)}, /* vin2a_d3.pr1_mi1_col */
- {VIN2A_D4, (M11 | PIN_INPUT_PULLDOWN)}, /* vin2a_d4.pr1_mii1_txd1 */
- {VIN2A_D5, (M11 | PIN_INPUT_PULLDOWN)}, /* vin2a_d5.pr1_mii1_txd0 */
- {VIN2A_D6, (M11 | PIN_INPUT_PULLDOWN)}, /* vin2a_d6.pr1_mii_mt1_clk */
- {VIN2A_D7, (M11 | PIN_INPUT_PULLDOWN)}, /* vin2a_d7.pr1_mii1_txen */
- {VIN2A_D8, (M11 | PIN_INPUT_PULLDOWN)}, /* vin2a_d8.pr1_mii1_txd3 */
- {VIN2A_D9, (M11 | PIN_INPUT_PULLDOWN)}, /* vin2a_d9.pr1_mii1_txd2 */
{VIN2A_D10, (M11 | PIN_INPUT_PULLDOWN)}, /* vin2a_d10.pr1_mdio_mdclk */
{VIN2A_D11, (M11 | PIN_INPUT_PULLUP)}, /* vin2a_d11.pr1_mdio_data */
{VIN2A_D12, (M3 | PIN_INPUT_PULLDOWN | MANUAL_MODE)}, /* vin2a_d12.rgmii1_txc */
@@ -570,35 +563,7 @@
{VIN2A_D21, (M3 | PIN_INPUT_PULLUP | MANUAL_MODE)}, /* vin2a_d21.rgmii1_rxd2 */
{VIN2A_D22, (M3 | PIN_INPUT_PULLUP | MANUAL_MODE)}, /* vin2a_d22.rgmii1_rxd1 */
{VIN2A_D23, (M3 | PIN_INPUT_PULLUP | MANUAL_MODE)}, /* vin2a_d23.rgmii1_rxd0 */
- {VOUT1_CLK, (M0 | PIN_INPUT_PULLDOWN)}, /* vout1_clk.vout1_clk */
- {VOUT1_DE, (M0 | PIN_INPUT_PULLDOWN)}, /* vout1_de.vout1_de */
{VOUT1_FLD, (M14 | PIN_INPUT_PULLUP)}, /* vout1_fld.gpio4_21 */
- {VOUT1_HSYNC, (M0 | PIN_INPUT_PULLDOWN)}, /* vout1_hsync.vout1_hsync */
- {VOUT1_VSYNC, (M0 | PIN_INPUT_PULLDOWN)}, /* vout1_vsync.vout1_vsync */
- {VOUT1_D0, (M0 | PIN_INPUT_PULLDOWN)}, /* vout1_d0.vout1_d0 */
- {VOUT1_D1, (M0 | PIN_INPUT_PULLDOWN)}, /* vout1_d1.vout1_d1 */
- {VOUT1_D2, (M0 | PIN_INPUT_PULLDOWN)}, /* vout1_d2.vout1_d2 */
- {VOUT1_D3, (M0 | PIN_INPUT_PULLDOWN)}, /* vout1_d3.vout1_d3 */
- {VOUT1_D4, (M0 | PIN_INPUT_PULLDOWN)}, /* vout1_d4.vout1_d4 */
- {VOUT1_D5, (M0 | PIN_INPUT_PULLDOWN)}, /* vout1_d5.vout1_d5 */
- {VOUT1_D6, (M0 | PIN_INPUT_PULLDOWN)}, /* vout1_d6.vout1_d6 */
- {VOUT1_D7, (M0 | PIN_INPUT_PULLDOWN)}, /* vout1_d7.vout1_d7 */
- {VOUT1_D8, (M0 | PIN_INPUT_PULLDOWN)}, /* vout1_d8.vout1_d8 */
- {VOUT1_D9, (M0 | PIN_INPUT_PULLDOWN)}, /* vout1_d9.vout1_d9 */
- {VOUT1_D10, (M0 | PIN_INPUT_PULLDOWN)}, /* vout1_d10.vout1_d10 */
- {VOUT1_D11, (M0 | PIN_INPUT_PULLDOWN)}, /* vout1_d11.vout1_d11 */
- {VOUT1_D12, (M0 | PIN_INPUT_PULLDOWN)}, /* vout1_d12.vout1_d12 */
- {VOUT1_D13, (M0 | PIN_INPUT_PULLDOWN)}, /* vout1_d13.vout1_d13 */
- {VOUT1_D14, (M0 | PIN_INPUT_PULLDOWN)}, /* vout1_d14.vout1_d14 */
- {VOUT1_D15, (M0 | PIN_INPUT_PULLDOWN)}, /* vout1_d15.vout1_d15 */
- {VOUT1_D16, (M0 | PIN_INPUT_PULLDOWN)}, /* vout1_d16.vout1_d16 */
- {VOUT1_D17, (M0 | PIN_INPUT_PULLDOWN)}, /* vout1_d17.vout1_d17 */
- {VOUT1_D18, (M0 | PIN_INPUT_PULLDOWN)}, /* vout1_d18.vout1_d18 */
- {VOUT1_D19, (M0 | PIN_INPUT_PULLDOWN)}, /* vout1_d19.vout1_d19 */
- {VOUT1_D20, (M0 | PIN_INPUT_PULLDOWN)}, /* vout1_d20.vout1_d20 */
- {VOUT1_D21, (M0 | PIN_INPUT_PULLDOWN)}, /* vout1_d21.vout1_d21 */
- {VOUT1_D22, (M0 | PIN_INPUT_PULLDOWN)}, /* vout1_d22.vout1_d22 */
- {VOUT1_D23, (M0 | PIN_INPUT_PULLDOWN)}, /* vout1_d23.vout1_d23 */
{MDIO_MCLK, (M0 | PIN_INPUT_PULLUP | SLEWCONTROL)}, /* mdio_mclk.mdio_mclk */
{MDIO_D, (M0 | PIN_INPUT_PULLUP | SLEWCONTROL)}, /* mdio_d.mdio_d */
{RMII_MHZ_50_CLK, (M13 | PIN_INPUT_PULLDOWN)}, /* RMII_MHZ_50_CLK.pr2_pru1_gpo2 */
@@ -727,6 +692,75 @@
{RSTOUTN, (M0 | PIN_OUTPUT_PULLDOWN)}, /* rstoutn.rstoutn */
};
+const struct pad_conf_entry core_padconf_array_icss1eth_am571x_idk[] = {
+ /* PR1 MII0 */
+ {VOUT1_D8, (M12 | PIN_INPUT_PULLDOWN)}, /* vout1_d8.pr1_mii_mt0_clk */
+ {VOUT1_D9, (M13 | PIN_OUTPUT)}, /* vout1_d9.pr1_mii0_txd3 */
+ {VOUT1_D10, (M13 | PIN_OUTPUT)}, /* vout1_d10.pr1_mii0_txd2 */
+ {VOUT1_D11, (M13 | PIN_OUTPUT)}, /* vout1_d11.pr1_mii0_txen */
+ {VOUT1_D12, (M13 | PIN_OUTPUT)}, /* vout1_d12.pr1_mii0_txd1 */
+ {VOUT1_D13, (M13 | PIN_OUTPUT)}, /* vout1_d13.pr1_mii0_txd0 */
+ {VOUT1_D14, (M12 | PIN_INPUT_PULLDOWN)}, /* vout1_d14.pr1_mii_mr0_clk */
+ {VOUT1_D15, (M12 | PIN_INPUT_PULLDOWN)}, /* vout1_d15.pr1_mii0_rxdv */
+ {VOUT1_D16, (M12 | PIN_INPUT)}, /* vout1_d16.pr1_mii0_rxd3 */
+ {VOUT1_D17, (M12 | PIN_INPUT)}, /* vout1_d17.pr1_mii0_rxd2 */
+ {VOUT1_D18, (M12 | PIN_INPUT)}, /* vout1_d18.pr1_mii0_rxd1 */
+ {VOUT1_D19, (M12 | PIN_INPUT)}, /* vout1_d19.pr1_mii0_rxd0 */
+ {VOUT1_D20, (M12 | PIN_INPUT_PULLUP)}, /* vout1_d20.pr1_mii0_rxer */
+ {VOUT1_D21, (M12 | PIN_INPUT)}, /* vout1_d21.pr1_mii0_rxlink */
+ {VOUT1_D22, (M12 | PIN_INPUT)}, /* vout1_d22.pr1_mii0_col */
+ {VOUT1_D23, (M12 | PIN_INPUT_PULLUP)}, /* vout1_d23.pr1_mii0_crs */
+
+ /* PR1 MII1 */
+ {VIN2A_D3, (M12 | PIN_INPUT)}, /* vin2a_d3.pr1_mi1_col */
+ {VIN2A_D4, (M13 | PIN_OUTPUT)}, /* vin2a_d4.pr1_mii1_txd1 */
+ {VIN2A_D5, (M13 | PIN_OUTPUT)}, /* vin2a_d5.pr1_mii1_txd0 */
+ {VIN2A_D6, (M11 | PIN_INPUT_PULLDOWN)}, /* vin2a_d6.pr1_mii_mt1_clk */
+ {VIN2A_D7, (M11 | PIN_OUTPUT)}, /* vin2a_d7.pr1_mii1_txen */
+ {VIN2A_D8, (M11 | PIN_OUTPUT)}, /* vin2a_d8.pr1_mii1_txd3 */
+ {VIN2A_D9, (M11 | PIN_OUTPUT)}, /* vin2a_d9.pr1_mii1_txd2 */
+ {VOUT1_VSYNC, (M12 | PIN_INPUT_PULLUP)}, /* vout1_vsync.pr1_mii1_rxer */
+ {VOUT1_D0, (M12 | PIN_INPUT)}, /* vout1_d0.pr1_mii1_rxlink */
+ {VOUT1_D1, (M12 | PIN_INPUT_PULLUP)}, /* vout1_d1.pr1_mii1_crs */
+ {VOUT1_D2, (M12 | PIN_INPUT_PULLDOWN)}, /* vout1_d2.pr1_mii_mr1_clk */
+ {VOUT1_D3, (M12 | PIN_INPUT_PULLDOWN)}, /* vout1_d3.pr1_mii1_rxdv */
+ {VOUT1_D4, (M12 | PIN_INPUT)}, /* vout1_d4.pr1_mii1_rxd3 */
+ {VOUT1_D5, (M12 | PIN_INPUT)}, /* vout1_d5.pr1_mii1_rxd2 */
+ {VOUT1_D6, (M12 | PIN_INPUT)}, /* vout1_d6.pr1_mii1_rxd1 */
+ {VOUT1_D7, (M12 | PIN_INPUT)}, /* vout1_d7.pr1_mii1_rxd0 */
+};
+
+const struct pad_conf_entry core_padconf_array_vout_am571x_idk[] = {
+ {VOUT1_CLK, (M0 | PIN_INPUT_PULLDOWN)}, /* vout1_clk.vout1_clk */
+ {VOUT1_DE, (M0 | PIN_INPUT_PULLDOWN)}, /* vout1_de.vout1_de */
+ {VOUT1_HSYNC, (M0 | PIN_INPUT_PULLDOWN)}, /* vout1_hsync.vout1_hsync */
+ {VOUT1_VSYNC, (M0 | PIN_INPUT_PULLDOWN)}, /* vout1_vsync.vout1_vsync */
+ {VOUT1_D0, (M0 | PIN_INPUT_PULLDOWN)}, /* vout1_d0.vout1_d0 */
+ {VOUT1_D1, (M0 | PIN_INPUT_PULLDOWN)}, /* vout1_d1.vout1_d1 */
+ {VOUT1_D2, (M0 | PIN_INPUT_PULLDOWN)}, /* vout1_d2.vout1_d2 */
+ {VOUT1_D3, (M0 | PIN_INPUT_PULLDOWN)}, /* vout1_d3.vout1_d3 */
+ {VOUT1_D4, (M0 | PIN_INPUT_PULLDOWN)}, /* vout1_d4.vout1_d4 */
+ {VOUT1_D5, (M0 | PIN_INPUT_PULLDOWN)}, /* vout1_d5.vout1_d5 */
+ {VOUT1_D6, (M0 | PIN_INPUT_PULLDOWN)}, /* vout1_d6.vout1_d6 */
+ {VOUT1_D7, (M0 | PIN_INPUT_PULLDOWN)}, /* vout1_d7.vout1_d7 */
+ {VOUT1_D8, (M0 | PIN_INPUT_PULLDOWN)}, /* vout1_d8.vout1_d8 */
+ {VOUT1_D9, (M0 | PIN_INPUT_PULLDOWN)}, /* vout1_d9.vout1_d9 */
+ {VOUT1_D10, (M0 | PIN_INPUT_PULLDOWN)}, /* vout1_d10.vout1_d10 */
+ {VOUT1_D11, (M0 | PIN_INPUT_PULLDOWN)}, /* vout1_d11.vout1_d11 */
+ {VOUT1_D12, (M0 | PIN_INPUT_PULLDOWN)}, /* vout1_d12.vout1_d12 */
+ {VOUT1_D13, (M0 | PIN_INPUT_PULLDOWN)}, /* vout1_d13.vout1_d13 */
+ {VOUT1_D14, (M0 | PIN_INPUT_PULLDOWN)}, /* vout1_d14.vout1_d14 */
+ {VOUT1_D15, (M0 | PIN_INPUT_PULLDOWN)}, /* vout1_d15.vout1_d15 */
+ {VOUT1_D16, (M0 | PIN_INPUT_PULLDOWN)}, /* vout1_d16.vout1_d16 */
+ {VOUT1_D17, (M0 | PIN_INPUT_PULLDOWN)}, /* vout1_d17.vout1_d17 */
+ {VOUT1_D18, (M0 | PIN_INPUT_PULLDOWN)}, /* vout1_d18.vout1_d18 */
+ {VOUT1_D19, (M0 | PIN_INPUT_PULLDOWN)}, /* vout1_d19.vout1_d19 */
+ {VOUT1_D20, (M0 | PIN_INPUT_PULLDOWN)}, /* vout1_d20.vout1_d20 */
+ {VOUT1_D21, (M0 | PIN_INPUT_PULLDOWN)}, /* vout1_d21.vout1_d21 */
+ {VOUT1_D22, (M0 | PIN_INPUT_PULLDOWN)}, /* vout1_d22.vout1_d22 */
+ {VOUT1_D23, (M0 | PIN_INPUT_PULLDOWN)}, /* vout1_d23.vout1_d23 */
+};
+
const struct pad_conf_entry early_padconf[] = {
{UART2_CTSN, (M2 | PIN_INPUT_SLEW)}, /* uart2_ctsn.uart3_rxd */
{UART2_RTSN, (M1 | PIN_INPUT_SLEW)}, /* uart2_rtsn.uart3_txd */