include/configs/omap3_beagle.h - platform/external/u-boot - Gitiles

 /*
  * (C) Copyright 2006-2008
  * Texas Instruments.
  * Richard Woodruff <r-woodruff2@ti.com>
  * Syed Mohammed Khasim <x0khasim@ti.com>
  *
  * Configuration settings for the TI OMAP3530 Beagle board.
  *
  * SPDX-License-Identifier:	GPL-2.0+
  */

 #ifndef __CONFIG_H
 #define __CONFIG_H

 /*
  * High Level Configuration Options
  */
 #define CONFIG_OMAP		1	/* in a TI OMAP core */
 #define CONFIG_OMAP34XX		1	/* which is a 34XX */
 #define CONFIG_OMAP3_BEAGLE	1	/* working with BEAGLE */
 #define CONFIG_OMAP_GPIO

 #define CONFIG_SDRC	/* The chip has SDRC controller */

 #include <asm/arch/cpu.h>		/* get chip and board defs */
 #include <asm/arch/omap3.h>

 /*
  * Display CPU and Board information
  */
 #define CONFIG_DISPLAY_CPUINFO		1
 #define CONFIG_DISPLAY_BOARDINFO	1

 /* Clock Defines */
 #define V_OSCK			26000000	/* Clock output from T2 */
 #define V_SCLK			(V_OSCK >> 1)

 #define CONFIG_MISC_INIT_R

 #define CONFIG_OF_LIBFDT
 #define CONFIG_CMD_BOOTZ

 #define CONFIG_CMDLINE_TAG		1	/* enable passing of ATAGs */
 #define CONFIG_SETUP_MEMORY_TAGS	1
 #define CONFIG_INITRD_TAG		1
 #define CONFIG_REVISION_TAG		1

 /*
  * Size of malloc() pool
  */
 #define CONFIG_ENV_SIZE			(128 << 10)	/* 128 KiB */
 						/* Sector */
 #define CONFIG_SYS_MALLOC_LEN		(CONFIG_ENV_SIZE + (128 << 10))

 /*
  * Hardware drivers
  */

 /*
  * NS16550 Configuration
  */
 #define V_NS16550_CLK			48000000	/* 48MHz (APLL96/2) */

 #define CONFIG_SYS_NS16550
 #define CONFIG_SYS_NS16550_SERIAL
 #define CONFIG_SYS_NS16550_REG_SIZE	(-4)
 #define CONFIG_SYS_NS16550_CLK		V_NS16550_CLK

 /*
  * select serial console configuration
  */
 #define CONFIG_CONS_INDEX		3
 #define CONFIG_SYS_NS16550_COM3		OMAP34XX_UART3
 #define CONFIG_SERIAL3			3	/* UART3 on Beagle Rev 2 */

 /* allow to overwrite serial and ethaddr */
 #define CONFIG_ENV_OVERWRITE
 #define CONFIG_BAUDRATE			115200
 #define CONFIG_SYS_BAUDRATE_TABLE	{4800, 9600, 19200, 38400, 57600,\
 					115200}
 #define CONFIG_GENERIC_MMC		1
 #define CONFIG_MMC			1
 #define CONFIG_OMAP_HSMMC		1
 #define CONFIG_DOS_PARTITION		1

 /* Status LED */
 #define CONFIG_STATUS_LED		1
 #define CONFIG_BOARD_SPECIFIC_LED	1
 #define STATUS_LED_BIT			0x01
 #define STATUS_LED_STATE		STATUS_LED_ON
 #define STATUS_LED_PERIOD		(CONFIG_SYS_HZ / 2)
 #define STATUS_LED_BIT1			0x02
 #define STATUS_LED_STATE1		STATUS_LED_ON
 #define STATUS_LED_PERIOD1		(CONFIG_SYS_HZ / 2)
 #define STATUS_LED_BOOT			STATUS_LED_BIT
 #define STATUS_LED_GREEN		STATUS_LED_BIT1

 /* Enable Multi Bus support for I2C */
 #define CONFIG_I2C_MULTI_BUS		1

 /* Probe all devices */
 #define CONFIG_SYS_I2C_NOPROBES		{{0x0, 0x0}}

 /* USB */
 #define CONFIG_MUSB_GADGET
 #define CONFIG_USB_MUSB_OMAP2PLUS
 #define CONFIG_MUSB_PIO_ONLY
 #define CONFIG_USB_GADGET_DUALSPEED
 #define CONFIG_TWL4030_USB		1
 #define CONFIG_USB_ETHER
 #define CONFIG_USB_ETHER_RNDIS

 /* USB EHCI */
 #define CONFIG_CMD_USB
 #define CONFIG_USB_EHCI

 #define CONFIG_USB_EHCI_OMAP
 #define CONFIG_OMAP_EHCI_PHY1_RESET_GPIO	147

 #define CONFIG_USB_ULPI
 #define CONFIG_USB_ULPI_VIEWPORT_OMAP

 #define CONFIG_SYS_USB_EHCI_MAX_ROOT_PORTS 3
 #define CONFIG_USB_HOST_ETHER
 #define CONFIG_USB_ETHER_SMSC95XX
 #define CONFIG_USB_ETHER_ASIX


 /* commands to include */
 #include <config_cmd_default.h>

 #define CONFIG_CMD_ASKENV

 #define CONFIG_CMD_CACHE
 #define CONFIG_CMD_EXT2		/* EXT2 Support			*/
 #define CONFIG_CMD_FAT		/* FAT support			*/
 #define CONFIG_CMD_FS_GENERIC	/* Generic FS support */
 #define CONFIG_CMD_MTDPARTS	/* Enable MTD parts commands */
 #define CONFIG_MTD_DEVICE	/* needed for mtdparts commands */
 #define MTDIDS_DEFAULT			"nand0=nand"
 #define MTDPARTS_DEFAULT		"mtdparts=nand:512k(x-loader),"\
 					"1920k(u-boot),128k(u-boot-env),"\
 					"4m(kernel),-(fs)"

 #define CONFIG_CMD_I2C		/* I2C serial bus support	*/
 #define CONFIG_CMD_MMC		/* MMC support			*/
 #define CONFIG_USB_STORAGE	/* USB storage support		*/
 #define CONFIG_CMD_NAND		/* NAND support			*/
 #define CONFIG_CMD_LED		/* LED support			*/
 #define CONFIG_CMD_NET      /* bootp, tftpboot, rarpboot    */
 #define CONFIG_CMD_NFS      /* NFS support          */
 #define CONFIG_CMD_PING
 #define CONFIG_CMD_DHCP
 #define CONFIG_CMD_SETEXPR	/* Evaluate expressions		*/
 #define CONFIG_CMD_GPIO     /* Enable gpio command */

 #undef CONFIG_CMD_FLASH		/* flinfo, erase, protect	*/
 #undef CONFIG_CMD_FPGA		/* FPGA configuration Support	*/
 #undef CONFIG_CMD_IMI		/* iminfo			*/
 #undef CONFIG_CMD_IMLS		/* List all found images	*/

 #define CONFIG_SYS_NO_FLASH
 #define CONFIG_HARD_I2C			1
 #define CONFIG_SYS_I2C_SPEED		100000
 #define CONFIG_SYS_I2C_SLAVE		1
 #define CONFIG_I2C_MULTI_BUS		1
 #define CONFIG_DRIVER_OMAP34XX_I2C	1
 #define CONFIG_VIDEO_OMAP3	/* DSS Support			*/

 /*
  * TWL4030
  */
 #define CONFIG_TWL4030_POWER		1
 #define CONFIG_TWL4030_LED		1

 /*
  * Board NAND Info.
  */
 #define CONFIG_SYS_NAND_QUIET_TEST	1
 #define CONFIG_NAND_OMAP_GPMC
 #define CONFIG_SYS_NAND_ADDR		NAND_BASE	/* physical address */
 							/* to access nand */
 #define CONFIG_SYS_NAND_BASE		NAND_BASE	/* physical address */
 							/* to access nand at */
 							/* CS0 */
 #define GPMC_NAND_ECC_LP_x16_LAYOUT	1

 #define CONFIG_SYS_MAX_NAND_DEVICE	1		/* Max number of NAND */
 							/* devices */

 /* Environment information */
 #define CONFIG_BOOTDELAY		3

 #define CONFIG_EXTRA_ENV_SETTINGS \
 	"loadaddr=0x80200000\0" \
 	"rdaddr=0x81000000\0" \
 	"fdt_high=0xffffffff\0" \
 	"fdtaddr=0x80f80000\0" \
 	"usbtty=cdc_acm\0" \
 	"bootfile=uImage\0" \
 	"ramdisk=ramdisk.gz\0" \
 	"bootdir=/boot\0" \
 	"bootpart=0:2\0" \
 	"console=ttyO2,115200n8\0" \
 	"mpurate=auto\0" \
 	"buddy=none\0" \
 	"optargs=\0" \
 	"camera=none\0" \
 	"vram=12M\0" \
 	"dvimode=640x480MR-16@60\0" \
 	"defaultdisplay=dvi\0" \
 	"mmcdev=0\0" \
 	"mmcroot=/dev/mmcblk0p2 rw\0" \
 	"mmcrootfstype=ext3 rootwait\0" \
 	"nandroot=ubi0:rootfs ubi.mtd=4\0" \
 	"nandrootfstype=ubifs\0" \
 	"ramroot=/dev/ram0 rw ramdisk_size=65536 initrd=0x81000000,64M\0" \
 	"ramrootfstype=ext2\0" \
 	"mmcargs=setenv bootargs console=${console} " \
 		"${optargs} " \
 		"mpurate=${mpurate} " \
 		"buddy=${buddy} "\
 		"camera=${camera} "\
 		"vram=${vram} " \
 		"omapfb.mode=dvi:${dvimode} " \
 		"omapdss.def_disp=${defaultdisplay} " \
 		"root=${mmcroot} " \
 		"rootfstype=${mmcrootfstype}\0" \
 	"nandargs=setenv bootargs console=${console} " \
 		"${optargs} " \
 		"mpurate=${mpurate} " \
 		"buddy=${buddy} "\
 		"camera=${camera} "\
 		"vram=${vram} " \
 		"omapfb.mode=dvi:${dvimode} " \
 		"omapdss.def_disp=${defaultdisplay} " \
 		"root=${nandroot} " \
 		"rootfstype=${nandrootfstype}\0" \
 	"findfdt=" \
 		"if test $beaglerev = AxBx; then " \
 			"setenv fdtfile omap3-beagle.dtb; fi; " \
 		"if test $beaglerev = Cx; then " \
 			"setenv fdtfile omap3-beagle.dtb; fi; " \
 		"if test $beaglerev = xMAB; then " \
 			"setenv fdtfile omap3-beagle-xm.dtb; fi; " \
 		"if test $beaglerev = xMC; then " \
 			"setenv fdtfile omap3-beagle-xm.dtb; fi; " \
 		"if test $fdtfile = undefined; then " \
 			"echo WARNING: Could not determine device tree to use; fi; \0" \
 	"bootenv=uEnv.txt\0" \
 	"loadbootenv=fatload mmc ${mmcdev} ${loadaddr} ${bootenv}\0" \
 	"importbootenv=echo Importing environment from mmc ...; " \
 		"env import -t $loadaddr $filesize\0" \
 	"ramargs=setenv bootargs console=${console} " \
 		"${optargs} " \
 		"mpurate=${mpurate} " \
 		"buddy=${buddy} "\
 		"vram=${vram} " \
 		"omapfb.mode=dvi:${dvimode} " \
 		"omapdss.def_disp=${defaultdisplay} " \
 		"root=${ramroot} " \
 		"rootfstype=${ramrootfstype}\0" \
 	"loadramdisk=load mmc ${bootpart} ${rdaddr} ${bootdir}/${ramdisk}\0" \
 	"loadimage=load mmc ${bootpart} ${loadaddr} ${bootdir}/${bootfile}\0" \
 	"loadfdt=load mmc ${bootpart} ${fdtaddr} ${bootdir}/${fdtfile}\0" \
 	"mmcboot=echo Booting from mmc ...; " \
 		"run mmcargs; " \
 		"bootm ${loadaddr}\0" \
 	"mmcbootz=echo Booting with DT from mmc${mmcdev} ...; " \
 		"run mmcargs; " \
 		"bootz ${loadaddr} - ${fdtaddr}\0" \
 	"nandboot=echo Booting from nand ...; " \
 		"run nandargs; " \
 		"nand read ${loadaddr} 280000 400000; " \
 		"bootm ${loadaddr}\0" \
 	"ramboot=echo Booting from ramdisk ...; " \
 		"run ramargs; " \
 		"bootm ${loadaddr}\0" \
 	"userbutton=if gpio input 173; then run userbutton_xm; " \
 		"else run userbutton_nonxm; fi;\0" \
 	"userbutton_xm=gpio input 4;\0" \
 	"userbutton_nonxm=gpio input 7;\0"
 /* "run userbutton" will return 1 (false) if pressed and 0 (true) if not */
 #define CONFIG_BOOTCOMMAND \
 	"run findfdt; " \
 	"mmc dev ${mmcdev}; if mmc rescan; then " \
 		"if run userbutton; then " \
 			"setenv bootenv uEnv.txt;" \
 		"else " \
 			"setenv bootenv user.txt;" \
 		"fi;" \
 		"echo SD/MMC found on device ${mmcdev};" \
 		"if run loadbootenv; then " \
 			"echo Loaded environment from ${bootenv};" \
 			"run importbootenv;" \
 		"fi;" \
 		"if test -n $uenvcmd; then " \
 			"echo Running uenvcmd ...;" \
 			"run uenvcmd;" \
 		"fi;" \
 		"if run loadimage; then " \
 			"run mmcboot;" \
 		"fi;" \
 	"fi;" \
 	"run nandboot;" \
 	"setenv bootfile zImage;" \
 	"if run loadimage; then " \
 		"run loadfdt;" \
 		"run mmcbootz; " \
 	"fi; " \

 #define CONFIG_AUTO_COMPLETE		1
 /*
  * Miscellaneous configurable options
  */
 #define CONFIG_SYS_LONGHELP		/* undef to save memory */
 #define CONFIG_SYS_HUSH_PARSER		/* use "hush" command parser */
 #define CONFIG_SYS_PROMPT		"OMAP3 beagleboard.org # "
 #define CONFIG_SYS_CBSIZE		512	/* Console I/O Buffer Size */
 /* Print Buffer Size */
 #define CONFIG_SYS_PBSIZE		(CONFIG_SYS_CBSIZE + \
 					sizeof(CONFIG_SYS_PROMPT) + 16)
 #define CONFIG_SYS_MAXARGS		32	/* max number of command args */
 /* Boot Argument Buffer Size */
 #define CONFIG_SYS_BARGSIZE		(CONFIG_SYS_CBSIZE)

 #define CONFIG_SYS_ALT_MEMTEST		1
 #define CONFIG_SYS_MEMTEST_START	(0x82000000)		/* memtest */
 								/* defaults */
 #define CONFIG_SYS_MEMTEST_END		(0x87FFFFFF) 		/* 128MB */
 #define CONFIG_SYS_MEMTEST_SCRATCH	(0x81000000)	/* dummy address */

 #define CONFIG_SYS_LOAD_ADDR		(OMAP34XX_SDRC_CS0)	/* default */
 							/* load address */

 /*
  * OMAP3 has 12 GP timers, they can be driven by the system clock
  * (12/13/16.8/19.2/38.4MHz) or by 32KHz clock. We use 13MHz (V_SCLK).
  * This rate is divided by a local divisor.
  */
 #define CONFIG_SYS_TIMERBASE		(OMAP34XX_GPT2)
 #define CONFIG_SYS_PTV			2       /* Divisor: 2^(PTV+1) => 8 */
 #define CONFIG_SYS_HZ			1000

 /*-----------------------------------------------------------------------
  * Physical Memory Map
  */
 #define CONFIG_NR_DRAM_BANKS	2	/* CS1 may or may not be populated */
 #define PHYS_SDRAM_1		OMAP34XX_SDRC_CS0
 #define PHYS_SDRAM_2		OMAP34XX_SDRC_CS1

 /*-----------------------------------------------------------------------
  * FLASH and environment organization
  */

 /* **** PISMO SUPPORT *** */

 /* Configure the PISMO */
 #define PISMO1_NAND_SIZE		GPMC_SIZE_128M
 #define PISMO1_ONEN_SIZE		GPMC_SIZE_128M

 #define CONFIG_SYS_MONITOR_LEN		(256 << 10)	/* Reserve 2 sectors */

 #if defined(CONFIG_CMD_NAND)
 #define CONFIG_SYS_FLASH_BASE		PISMO1_NAND_BASE
 #endif

 /* Monitor at start of flash */
 #define CONFIG_SYS_MONITOR_BASE		CONFIG_SYS_FLASH_BASE
 #define CONFIG_SYS_ONENAND_BASE		ONENAND_MAP

 #define CONFIG_ENV_IS_IN_NAND		1
 #define ONENAND_ENV_OFFSET		0x260000 /* environment starts here */
 #define SMNAND_ENV_OFFSET		0x260000 /* environment starts here */

 #define CONFIG_SYS_ENV_SECT_SIZE	(128 << 10)	/* 128 KiB */
 #define CONFIG_ENV_OFFSET		SMNAND_ENV_OFFSET
 #define CONFIG_ENV_ADDR			SMNAND_ENV_OFFSET

 #define CONFIG_SYS_SDRAM_BASE		PHYS_SDRAM_1
 #define CONFIG_SYS_INIT_RAM_ADDR	0x4020f800
 #define CONFIG_SYS_INIT_RAM_SIZE	0x800
 #define CONFIG_SYS_INIT_SP_ADDR		(CONFIG_SYS_INIT_RAM_ADDR + \
 					 CONFIG_SYS_INIT_RAM_SIZE - \
 					 GENERATED_GBL_DATA_SIZE)

 #define CONFIG_OMAP3_SPI

 #define CONFIG_SYS_CACHELINE_SIZE	64

 /* Defines for SPL */
 #define CONFIG_SPL
 #define CONFIG_SPL_FRAMEWORK
 #define CONFIG_SPL_NAND_SIMPLE
 #define CONFIG_SPL_TEXT_BASE		0x40200800
 #define CONFIG_SPL_MAX_SIZE		(54 * 1024)	/* 8 KB for stack */
 #define CONFIG_SPL_STACK		LOW_LEVEL_SRAM_STACK

 #define CONFIG_SPL_BSS_START_ADDR	0x80000000
 #define CONFIG_SPL_BSS_MAX_SIZE		0x80000		/* 512 KB */

 #define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR	0x300 /* address 0x60000 */
 #define CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS	0x200 /* 256 KB */
 #define CONFIG_SYS_MMC_SD_FAT_BOOT_PARTITION	1
 #define CONFIG_SPL_FAT_LOAD_PAYLOAD_NAME	"u-boot.img"

 #define CONFIG_SPL_BOARD_INIT
 #define CONFIG_SPL_LIBCOMMON_SUPPORT
 #define CONFIG_SPL_LIBDISK_SUPPORT
 #define CONFIG_SPL_I2C_SUPPORT
 #define CONFIG_SPL_LIBGENERIC_SUPPORT
 #define CONFIG_SPL_MMC_SUPPORT
 #define CONFIG_SPL_FAT_SUPPORT
 #define CONFIG_SPL_SERIAL_SUPPORT
 #define CONFIG_SPL_NAND_SUPPORT
 #define CONFIG_SPL_NAND_BASE
 #define CONFIG_SPL_NAND_DRIVERS
 #define CONFIG_SPL_NAND_ECC
 #define CONFIG_SPL_GPIO_SUPPORT
 #define CONFIG_SPL_POWER_SUPPORT
 #define CONFIG_SPL_OMAP3_ID_NAND
 #define CONFIG_SPL_LDSCRIPT		"$(CPUDIR)/omap-common/u-boot-spl.lds"

 /* NAND boot config */
 #define CONFIG_SYS_NAND_5_ADDR_CYCLE
 #define CONFIG_SYS_NAND_PAGE_COUNT	64
 #define CONFIG_SYS_NAND_PAGE_SIZE	2048
 #define CONFIG_SYS_NAND_OOBSIZE		64
 #define CONFIG_SYS_NAND_BLOCK_SIZE	(128*1024)
 #define CONFIG_SYS_NAND_BAD_BLOCK_POS	0
 #define CONFIG_SYS_NAND_ECCPOS		{2, 3, 4, 5, 6, 7, 8, 9,\
 						10, 11, 12, 13}
 #define CONFIG_SYS_NAND_ECCSIZE		512
 #define CONFIG_SYS_NAND_ECCBYTES	3
 #define CONFIG_SYS_NAND_U_BOOT_START	CONFIG_SYS_TEXT_BASE
 #define CONFIG_SYS_NAND_U_BOOT_OFFS	0x80000

 /*
  * 1MB into the SDRAM to allow for SPL's bss at the beginning of SDRAM
  * 64 bytes before this address should be set aside for u-boot.img's
  * header. That is 0x800FFFC0--0x80100000 should not be used for any
  * other needs.
  */
 #define CONFIG_SYS_TEXT_BASE		0x80100000
 #define CONFIG_SYS_SPL_MALLOC_START	0x80208000
 #define CONFIG_SYS_SPL_MALLOC_SIZE	0x100000

 #endif /* __CONFIG_H */
	/*
	* (C) Copyright 2006-2008
	* Texas Instruments.
	* Richard Woodruff <r-woodruff2@ti.com>
	* Syed Mohammed Khasim <x0khasim@ti.com>
	*
	* Configuration settings for the TI OMAP3530 Beagle board.
	*
	* SPDX-License-Identifier: GPL-2.0+
	*/

	#ifndef __CONFIG_H
	#define __CONFIG_H

	/*
	* High Level Configuration Options
	*/
	#define CONFIG_OMAP 1 /* in a TI OMAP core */
	#define CONFIG_OMAP34XX 1 /* which is a 34XX */
	#define CONFIG_OMAP3_BEAGLE 1 /* working with BEAGLE */
	#define CONFIG_OMAP_GPIO

	#define CONFIG_SDRC /* The chip has SDRC controller */

	#include <asm/arch/cpu.h> /* get chip and board defs */
	#include <asm/arch/omap3.h>

	/*
	* Display CPU and Board information
	*/
	#define CONFIG_DISPLAY_CPUINFO 1
	#define CONFIG_DISPLAY_BOARDINFO 1

	/* Clock Defines */
	#define V_OSCK 26000000 /* Clock output from T2 */
	#define V_SCLK (V_OSCK >> 1)

	#define CONFIG_MISC_INIT_R

	#define CONFIG_OF_LIBFDT
	#define CONFIG_CMD_BOOTZ

	#define CONFIG_CMDLINE_TAG 1 /* enable passing of ATAGs */
	#define CONFIG_SETUP_MEMORY_TAGS 1
	#define CONFIG_INITRD_TAG 1
	#define CONFIG_REVISION_TAG 1

	/*
	* Size of malloc() pool
	*/
	#define CONFIG_ENV_SIZE (128 << 10) /* 128 KiB */
	/* Sector */
	#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + (128 << 10))

	/*
	* Hardware drivers
	*/

	/*
	* NS16550 Configuration
	*/
	#define V_NS16550_CLK 48000000 /* 48MHz (APLL96/2) */

	#define CONFIG_SYS_NS16550
	#define CONFIG_SYS_NS16550_SERIAL
	#define CONFIG_SYS_NS16550_REG_SIZE (-4)
	#define CONFIG_SYS_NS16550_CLK V_NS16550_CLK

	/*
	* select serial console configuration
	*/
	#define CONFIG_CONS_INDEX 3
	#define CONFIG_SYS_NS16550_COM3 OMAP34XX_UART3
	#define CONFIG_SERIAL3 3 /* UART3 on Beagle Rev 2 */

	/* allow to overwrite serial and ethaddr */
	#define CONFIG_ENV_OVERWRITE
	#define CONFIG_BAUDRATE 115200
	#define CONFIG_SYS_BAUDRATE_TABLE {4800, 9600, 19200, 38400, 57600,\
	115200}
	#define CONFIG_GENERIC_MMC 1
	#define CONFIG_MMC 1
	#define CONFIG_OMAP_HSMMC 1
	#define CONFIG_DOS_PARTITION 1

	/* Status LED */
	#define CONFIG_STATUS_LED 1
	#define CONFIG_BOARD_SPECIFIC_LED 1
	#define STATUS_LED_BIT 0x01
	#define STATUS_LED_STATE STATUS_LED_ON
	#define STATUS_LED_PERIOD (CONFIG_SYS_HZ / 2)
	#define STATUS_LED_BIT1 0x02
	#define STATUS_LED_STATE1 STATUS_LED_ON
	#define STATUS_LED_PERIOD1 (CONFIG_SYS_HZ / 2)
	#define STATUS_LED_BOOT STATUS_LED_BIT
	#define STATUS_LED_GREEN STATUS_LED_BIT1

	/* Enable Multi Bus support for I2C */
	#define CONFIG_I2C_MULTI_BUS 1

	/* Probe all devices */
	#define CONFIG_SYS_I2C_NOPROBES {{0x0, 0x0}}

	/* USB */
	#define CONFIG_MUSB_GADGET
	#define CONFIG_USB_MUSB_OMAP2PLUS
	#define CONFIG_MUSB_PIO_ONLY
	#define CONFIG_USB_GADGET_DUALSPEED
	#define CONFIG_TWL4030_USB 1
	#define CONFIG_USB_ETHER
	#define CONFIG_USB_ETHER_RNDIS

	/* USB EHCI */
	#define CONFIG_CMD_USB
	#define CONFIG_USB_EHCI

	#define CONFIG_USB_EHCI_OMAP
	#define CONFIG_OMAP_EHCI_PHY1_RESET_GPIO 147

	#define CONFIG_USB_ULPI
	#define CONFIG_USB_ULPI_VIEWPORT_OMAP

	#define CONFIG_SYS_USB_EHCI_MAX_ROOT_PORTS 3
	#define CONFIG_USB_HOST_ETHER
	#define CONFIG_USB_ETHER_SMSC95XX
	#define CONFIG_USB_ETHER_ASIX


	/* commands to include */
	#include <config_cmd_default.h>

	#define CONFIG_CMD_ASKENV

	#define CONFIG_CMD_CACHE
	#define CONFIG_CMD_EXT2 /* EXT2 Support */
	#define CONFIG_CMD_FAT /* FAT support */
	#define CONFIG_CMD_FS_GENERIC /* Generic FS support */
	#define CONFIG_CMD_MTDPARTS /* Enable MTD parts commands */
	#define CONFIG_MTD_DEVICE /* needed for mtdparts commands */
	#define MTDIDS_DEFAULT "nand0=nand"
	#define MTDPARTS_DEFAULT "mtdparts=nand:512k(x-loader),"\
	"1920k(u-boot),128k(u-boot-env),"\
	"4m(kernel),-(fs)"

	#define CONFIG_CMD_I2C /* I2C serial bus support */
	#define CONFIG_CMD_MMC /* MMC support */
	#define CONFIG_USB_STORAGE /* USB storage support */
	#define CONFIG_CMD_NAND /* NAND support */
	#define CONFIG_CMD_LED /* LED support */
	#define CONFIG_CMD_NET /* bootp, tftpboot, rarpboot */
	#define CONFIG_CMD_NFS /* NFS support */
	#define CONFIG_CMD_PING
	#define CONFIG_CMD_DHCP
	#define CONFIG_CMD_SETEXPR /* Evaluate expressions */
	#define CONFIG_CMD_GPIO /* Enable gpio command */

	#undef CONFIG_CMD_FLASH /* flinfo, erase, protect */
	#undef CONFIG_CMD_FPGA /* FPGA configuration Support */
	#undef CONFIG_CMD_IMI /* iminfo */
	#undef CONFIG_CMD_IMLS /* List all found images */

	#define CONFIG_SYS_NO_FLASH
	#define CONFIG_HARD_I2C 1
	#define CONFIG_SYS_I2C_SPEED 100000
	#define CONFIG_SYS_I2C_SLAVE 1
	#define CONFIG_I2C_MULTI_BUS 1
	#define CONFIG_DRIVER_OMAP34XX_I2C 1
	#define CONFIG_VIDEO_OMAP3 /* DSS Support */

	/*
	* TWL4030
	*/
	#define CONFIG_TWL4030_POWER 1
	#define CONFIG_TWL4030_LED 1

	/*
	* Board NAND Info.
	*/
	#define CONFIG_SYS_NAND_QUIET_TEST 1
	#define CONFIG_NAND_OMAP_GPMC
	#define CONFIG_SYS_NAND_ADDR NAND_BASE /* physical address */
	/* to access nand */
	#define CONFIG_SYS_NAND_BASE NAND_BASE /* physical address */
	/* to access nand at */
	/* CS0 */
	#define GPMC_NAND_ECC_LP_x16_LAYOUT 1

	#define CONFIG_SYS_MAX_NAND_DEVICE 1 /* Max number of NAND */
	/* devices */

	/* Environment information */
	#define CONFIG_BOOTDELAY 3

	#define CONFIG_EXTRA_ENV_SETTINGS \
	"loadaddr=0x80200000\0" \
	"rdaddr=0x81000000\0" \
	"fdt_high=0xffffffff\0" \
	"fdtaddr=0x80f80000\0" \
	"usbtty=cdc_acm\0" \
	"bootfile=uImage\0" \
	"ramdisk=ramdisk.gz\0" \
	"bootdir=/boot\0" \
	"bootpart=0:2\0" \
	"console=ttyO2,115200n8\0" \
	"mpurate=auto\0" \
	"buddy=none\0" \
	"optargs=\0" \
	"camera=none\0" \
	"vram=12M\0" \
	"dvimode=640x480MR-16@60\0" \
	"defaultdisplay=dvi\0" \
	"mmcdev=0\0" \
	"mmcroot=/dev/mmcblk0p2 rw\0" \
	"mmcrootfstype=ext3 rootwait\0" \
	"nandroot=ubi0:rootfs ubi.mtd=4\0" \
	"nandrootfstype=ubifs\0" \
	"ramroot=/dev/ram0 rw ramdisk_size=65536 initrd=0x81000000,64M\0" \
	"ramrootfstype=ext2\0" \
	"mmcargs=setenv bootargs console=${console} " \
	"${optargs} " \
	"mpurate=${mpurate} " \
	"buddy=${buddy} "\
	"camera=${camera} "\
	"vram=${vram} " \
	"omapfb.mode=dvi:${dvimode} " \
	"omapdss.def_disp=${defaultdisplay} " \
	"root=${mmcroot} " \
	"rootfstype=${mmcrootfstype}\0" \
	"nandargs=setenv bootargs console=${console} " \
	"${optargs} " \
	"mpurate=${mpurate} " \
	"buddy=${buddy} "\
	"camera=${camera} "\
	"vram=${vram} " \
	"omapfb.mode=dvi:${dvimode} " \
	"omapdss.def_disp=${defaultdisplay} " \
	"root=${nandroot} " \
	"rootfstype=${nandrootfstype}\0" \
	"findfdt=" \
	"if test $beaglerev = AxBx; then " \
	"setenv fdtfile omap3-beagle.dtb; fi; " \
	"if test $beaglerev = Cx; then " \
	"setenv fdtfile omap3-beagle.dtb; fi; " \
	"if test $beaglerev = xMAB; then " \
	"setenv fdtfile omap3-beagle-xm.dtb; fi; " \
	"if test $beaglerev = xMC; then " \
	"setenv fdtfile omap3-beagle-xm.dtb; fi; " \
	"if test $fdtfile = undefined; then " \
	"echo WARNING: Could not determine device tree to use; fi; \0" \
	"bootenv=uEnv.txt\0" \
	"loadbootenv=fatload mmc ${mmcdev} ${loadaddr} ${bootenv}\0" \
	"importbootenv=echo Importing environment from mmc ...; " \
	"env import -t $loadaddr $filesize\0" \
	"ramargs=setenv bootargs console=${console} " \
	"${optargs} " \
	"mpurate=${mpurate} " \
	"buddy=${buddy} "\
	"vram=${vram} " \
	"omapfb.mode=dvi:${dvimode} " \
	"omapdss.def_disp=${defaultdisplay} " \
	"root=${ramroot} " \
	"rootfstype=${ramrootfstype}\0" \
	"loadramdisk=load mmc ${bootpart} ${rdaddr} ${bootdir}/${ramdisk}\0" \
	"loadimage=load mmc ${bootpart} ${loadaddr} ${bootdir}/${bootfile}\0" \
	"loadfdt=load mmc ${bootpart} ${fdtaddr} ${bootdir}/${fdtfile}\0" \
	"mmcboot=echo Booting from mmc ...; " \
	"run mmcargs; " \
	"bootm ${loadaddr}\0" \
	"mmcbootz=echo Booting with DT from mmc${mmcdev} ...; " \
	"run mmcargs; " \
	"bootz ${loadaddr} - ${fdtaddr}\0" \
	"nandboot=echo Booting from nand ...; " \
	"run nandargs; " \
	"nand read ${loadaddr} 280000 400000; " \
	"bootm ${loadaddr}\0" \
	"ramboot=echo Booting from ramdisk ...; " \
	"run ramargs; " \
	"bootm ${loadaddr}\0" \
	"userbutton=if gpio input 173; then run userbutton_xm; " \
	"else run userbutton_nonxm; fi;\0" \
	"userbutton_xm=gpio input 4;\0" \
	"userbutton_nonxm=gpio input 7;\0"
	/* "run userbutton" will return 1 (false) if pressed and 0 (true) if not */
	#define CONFIG_BOOTCOMMAND \
	"run findfdt; " \
	"mmc dev ${mmcdev}; if mmc rescan; then " \
	"if run userbutton; then " \
	"setenv bootenv uEnv.txt;" \
	"else " \
	"setenv bootenv user.txt;" \
	"fi;" \
	"echo SD/MMC found on device ${mmcdev};" \
	"if run loadbootenv; then " \
	"echo Loaded environment from ${bootenv};" \
	"run importbootenv;" \
	"fi;" \
	"if test -n $uenvcmd; then " \
	"echo Running uenvcmd ...;" \
	"run uenvcmd;" \
	"fi;" \
	"if run loadimage; then " \
	"run mmcboot;" \
	"fi;" \
	"fi;" \
	"run nandboot;" \
	"setenv bootfile zImage;" \
	"if run loadimage; then " \
	"run loadfdt;" \
	"run mmcbootz; " \
	"fi; " \

	#define CONFIG_AUTO_COMPLETE 1
	/*
	* Miscellaneous configurable options
	*/
	#define CONFIG_SYS_LONGHELP /* undef to save memory */
	#define CONFIG_SYS_HUSH_PARSER /* use "hush" command parser */
	#define CONFIG_SYS_PROMPT "OMAP3 beagleboard.org # "
	#define CONFIG_SYS_CBSIZE 512 /* Console I/O Buffer Size */
	/* Print Buffer Size */
	#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \
	sizeof(CONFIG_SYS_PROMPT) + 16)
	#define CONFIG_SYS_MAXARGS 32 /* max number of command args */
	/* Boot Argument Buffer Size */
	#define CONFIG_SYS_BARGSIZE (CONFIG_SYS_CBSIZE)

	#define CONFIG_SYS_ALT_MEMTEST 1
	#define CONFIG_SYS_MEMTEST_START (0x82000000) /* memtest */
	/* defaults */
	#define CONFIG_SYS_MEMTEST_END (0x87FFFFFF) /* 128MB */
	#define CONFIG_SYS_MEMTEST_SCRATCH (0x81000000) /* dummy address */

	#define CONFIG_SYS_LOAD_ADDR (OMAP34XX_SDRC_CS0) /* default */
	/* load address */

	/*
	* OMAP3 has 12 GP timers, they can be driven by the system clock
	* (12/13/16.8/19.2/38.4MHz) or by 32KHz clock. We use 13MHz (V_SCLK).
	* This rate is divided by a local divisor.
	*/
	#define CONFIG_SYS_TIMERBASE (OMAP34XX_GPT2)
	#define CONFIG_SYS_PTV 2 /* Divisor: 2^(PTV+1) => 8 */
	#define CONFIG_SYS_HZ 1000

	/*-----------------------------------------------------------------------
	* Physical Memory Map
	*/
	#define CONFIG_NR_DRAM_BANKS 2 /* CS1 may or may not be populated */
	#define PHYS_SDRAM_1 OMAP34XX_SDRC_CS0
	#define PHYS_SDRAM_2 OMAP34XX_SDRC_CS1

	/*-----------------------------------------------------------------------
	* FLASH and environment organization
	*/

	/* ** PISMO SUPPORT * */

	/* Configure the PISMO */
	#define PISMO1_NAND_SIZE GPMC_SIZE_128M
	#define PISMO1_ONEN_SIZE GPMC_SIZE_128M

	#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 2 sectors */

	#if defined(CONFIG_CMD_NAND)
	#define CONFIG_SYS_FLASH_BASE PISMO1_NAND_BASE
	#endif

	/* Monitor at start of flash */
	#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE
	#define CONFIG_SYS_ONENAND_BASE ONENAND_MAP

	#define CONFIG_ENV_IS_IN_NAND 1
	#define ONENAND_ENV_OFFSET 0x260000 /* environment starts here */
	#define SMNAND_ENV_OFFSET 0x260000 /* environment starts here */

	#define CONFIG_SYS_ENV_SECT_SIZE (128 << 10) /* 128 KiB */
	#define CONFIG_ENV_OFFSET SMNAND_ENV_OFFSET
	#define CONFIG_ENV_ADDR SMNAND_ENV_OFFSET

	#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1
	#define CONFIG_SYS_INIT_RAM_ADDR 0x4020f800
	#define CONFIG_SYS_INIT_RAM_SIZE 0x800
	#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_INIT_RAM_ADDR + \
	CONFIG_SYS_INIT_RAM_SIZE - \
	GENERATED_GBL_DATA_SIZE)

	#define CONFIG_OMAP3_SPI

	#define CONFIG_SYS_CACHELINE_SIZE 64

	/* Defines for SPL */
	#define CONFIG_SPL
	#define CONFIG_SPL_FRAMEWORK
	#define CONFIG_SPL_NAND_SIMPLE
	#define CONFIG_SPL_TEXT_BASE 0x40200800
	#define CONFIG_SPL_MAX_SIZE (54 * 1024) /* 8 KB for stack */
	#define CONFIG_SPL_STACK LOW_LEVEL_SRAM_STACK

	#define CONFIG_SPL_BSS_START_ADDR 0x80000000
	#define CONFIG_SPL_BSS_MAX_SIZE 0x80000 /* 512 KB */

	#define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR 0x300 /* address 0x60000 */
	#define CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS 0x200 /* 256 KB */
	#define CONFIG_SYS_MMC_SD_FAT_BOOT_PARTITION 1
	#define CONFIG_SPL_FAT_LOAD_PAYLOAD_NAME "u-boot.img"

	#define CONFIG_SPL_BOARD_INIT
	#define CONFIG_SPL_LIBCOMMON_SUPPORT
	#define CONFIG_SPL_LIBDISK_SUPPORT
	#define CONFIG_SPL_I2C_SUPPORT
	#define CONFIG_SPL_LIBGENERIC_SUPPORT
	#define CONFIG_SPL_MMC_SUPPORT
	#define CONFIG_SPL_FAT_SUPPORT
	#define CONFIG_SPL_SERIAL_SUPPORT
	#define CONFIG_SPL_NAND_SUPPORT
	#define CONFIG_SPL_NAND_BASE
	#define CONFIG_SPL_NAND_DRIVERS
	#define CONFIG_SPL_NAND_ECC
	#define CONFIG_SPL_GPIO_SUPPORT
	#define CONFIG_SPL_POWER_SUPPORT
	#define CONFIG_SPL_OMAP3_ID_NAND
	#define CONFIG_SPL_LDSCRIPT "$(CPUDIR)/omap-common/u-boot-spl.lds"

	/* NAND boot config */
	#define CONFIG_SYS_NAND_5_ADDR_CYCLE
	#define CONFIG_SYS_NAND_PAGE_COUNT 64
	#define CONFIG_SYS_NAND_PAGE_SIZE 2048
	#define CONFIG_SYS_NAND_OOBSIZE 64
	#define CONFIG_SYS_NAND_BLOCK_SIZE (128*1024)
	#define CONFIG_SYS_NAND_BAD_BLOCK_POS 0
	#define CONFIG_SYS_NAND_ECCPOS {2, 3, 4, 5, 6, 7, 8, 9,\
	10, 11, 12, 13}
	#define CONFIG_SYS_NAND_ECCSIZE 512
	#define CONFIG_SYS_NAND_ECCBYTES 3
	#define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_TEXT_BASE
	#define CONFIG_SYS_NAND_U_BOOT_OFFS 0x80000

	/*
	* 1MB into the SDRAM to allow for SPL's bss at the beginning of SDRAM
	* 64 bytes before this address should be set aside for u-boot.img's
	* header. That is 0x800FFFC0--0x80100000 should not be used for any
	* other needs.
	*/
	#define CONFIG_SYS_TEXT_BASE 0x80100000
	#define CONFIG_SYS_SPL_MALLOC_START 0x80208000
	#define CONFIG_SYS_SPL_MALLOC_SIZE 0x100000

	#endif /* __CONFIG_H */