* Patch by Ronen Shitrit, 10 Dec 2003:
Add support for the Marvell DB64360 / DB64460 development boards
* Patch by Detlev Zundel, 10 Dec 2003:
fix dependency problem in examples/Makefile
diff --git a/board/Marvell/db64460/sdram_init.c b/board/Marvell/db64460/sdram_init.c
new file mode 100644
index 0000000..8cfe84c
--- /dev/null
+++ b/board/Marvell/db64460/sdram_init.c
@@ -0,0 +1,1985 @@
+/*
+ * (C) Copyright 2001
+ * Josh Huber <huber@mclx.com>, Mission Critical Linux, Inc.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+/*************************************************************************
+ * adaption for the Marvell DB64460 Board
+ * Ingo Assmus (ingo.assmus@keymile.com)
+ ************************************************************************/
+
+
+/* sdram_init.c - automatic memory sizing */
+
+#include <common.h>
+#include <74xx_7xx.h>
+#include "../include/memory.h"
+#include "../include/pci.h"
+#include "../include/mv_gen_reg.h"
+#include <net.h>
+
+#include "eth.h"
+#include "mpsc.h"
+#include "../common/i2c.h"
+#include "64460.h"
+#include "mv_regs.h"
+
+#undef DEBUG
+#define MAP_PCI
+
+#ifdef DEBUG
+#define DP(x) x
+#else
+#define DP(x)
+#endif
+
+int set_dfcdlInit (void); /* setup delay line of Mv64460 */
+int mvDmaIsChannelActive (int);
+int mvDmaSetMemorySpace (ulong, ulong, ulong, ulong, ulong);
+int mvDmaTransfer (int, ulong, ulong, ulong, ulong);
+
+/* ------------------------------------------------------------------------- */
+
+int
+memory_map_bank (unsigned int bankNo,
+ unsigned int bankBase, unsigned int bankLength)
+{
+#ifdef MAP_PCI
+ PCI_HOST host;
+#endif
+
+
+#ifdef DEBUG
+ if (bankLength > 0) {
+ printf ("mapping bank %d at %08x - %08x\n",
+ bankNo, bankBase, bankBase + bankLength - 1);
+ } else {
+ printf ("unmapping bank %d\n", bankNo);
+ }
+#endif
+
+ memoryMapBank (bankNo, bankBase, bankLength);
+
+#ifdef MAP_PCI
+ for (host = PCI_HOST0; host <= PCI_HOST1; host++) {
+ const int features =
+ PREFETCH_ENABLE |
+ DELAYED_READ_ENABLE |
+ AGGRESSIVE_PREFETCH |
+ READ_LINE_AGGRESSIVE_PREFETCH |
+ READ_MULTI_AGGRESSIVE_PREFETCH |
+ MAX_BURST_4 | PCI_NO_SWAP;
+
+ pciMapMemoryBank (host, bankNo, bankBase, bankLength);
+
+ pciSetRegionSnoopMode (host, bankNo, PCI_SNOOP_WB, bankBase,
+ bankLength);
+
+ pciSetRegionFeatures (host, bankNo, features, bankBase,
+ bankLength);
+ }
+#endif
+ return 0;
+}
+
+#define GB (1 << 30)
+
+/* much of this code is based on (or is) the code in the pip405 port */
+/* thanks go to the authors of said port - Josh */
+
+/* structure to store the relevant information about an sdram bank */
+typedef struct sdram_info {
+ uchar drb_size;
+ uchar registered, ecc;
+ uchar tpar;
+ uchar tras_clocks;
+ uchar burst_len;
+ uchar banks, slot;
+} sdram_info_t;
+
+/* Typedefs for 'gtAuxilGetDIMMinfo' function */
+
+typedef enum _memoryType { SDRAM, DDR } MEMORY_TYPE;
+
+typedef enum _voltageInterface { TTL_5V_TOLERANT, LVTTL, HSTL_1_5V,
+ SSTL_3_3V, SSTL_2_5V, VOLTAGE_UNKNOWN,
+} VOLTAGE_INTERFACE;
+
+typedef enum _max_CL_supported_DDR { DDR_CL_1 = 1, DDR_CL_1_5 = 2, DDR_CL_2 =
+ 4, DDR_CL_2_5 = 8, DDR_CL_3 = 16, DDR_CL_3_5 =
+ 32, DDR_CL_FAULT } MAX_CL_SUPPORTED_DDR;
+typedef enum _max_CL_supported_SD { SD_CL_1 =
+ 1, SD_CL_2, SD_CL_3, SD_CL_4, SD_CL_5, SD_CL_6, SD_CL_7,
+ SD_FAULT } MAX_CL_SUPPORTED_SD;
+
+
+/* SDRAM/DDR information struct */
+typedef struct _gtMemoryDimmInfo {
+ MEMORY_TYPE memoryType;
+ unsigned int numOfRowAddresses;
+ unsigned int numOfColAddresses;
+ unsigned int numOfModuleBanks;
+ unsigned int dataWidth;
+ VOLTAGE_INTERFACE voltageInterface;
+ unsigned int errorCheckType; /* ECC , PARITY.. */
+ unsigned int sdramWidth; /* 4,8,16 or 32 */ ;
+ unsigned int errorCheckDataWidth; /* 0 - no, 1 - Yes */
+ unsigned int minClkDelay;
+ unsigned int burstLengthSupported;
+ unsigned int numOfBanksOnEachDevice;
+ unsigned int suportedCasLatencies;
+ unsigned int RefreshInterval;
+ unsigned int maxCASlatencySupported_LoP; /* LoP left of point (measured in ns) */
+ unsigned int maxCASlatencySupported_RoP; /* RoP right of point (measured in ns) */
+ MAX_CL_SUPPORTED_DDR maxClSupported_DDR;
+ MAX_CL_SUPPORTED_SD maxClSupported_SD;
+ unsigned int moduleBankDensity;
+ /* module attributes (true for yes) */
+ bool bufferedAddrAndControlInputs;
+ bool registeredAddrAndControlInputs;
+ bool onCardPLL;
+ bool bufferedDQMBinputs;
+ bool registeredDQMBinputs;
+ bool differentialClockInput;
+ bool redundantRowAddressing;
+
+ /* module general attributes */
+ bool suportedAutoPreCharge;
+ bool suportedPreChargeAll;
+ bool suportedEarlyRasPreCharge;
+ bool suportedWrite1ReadBurst;
+ bool suported5PercentLowVCC;
+ bool suported5PercentUpperVCC;
+ /* module timing parameters */
+ unsigned int minRasToCasDelay;
+ unsigned int minRowActiveRowActiveDelay;
+ unsigned int minRasPulseWidth;
+ unsigned int minRowPrechargeTime; /* measured in ns */
+
+ int addrAndCommandHoldTime; /* LoP left of point (measured in ns) */
+ int addrAndCommandSetupTime; /* (measured in ns/100) */
+ int dataInputSetupTime; /* LoP left of point (measured in ns) */
+ int dataInputHoldTime; /* LoP left of point (measured in ns) */
+/* tAC times for highest 2nd and 3rd highest CAS Latency values */
+ unsigned int clockToDataOut_LoP; /* LoP left of point (measured in ns) */
+ unsigned int clockToDataOut_RoP; /* RoP right of point (measured in ns) */
+ unsigned int clockToDataOutMinus1_LoP; /* LoP left of point (measured in ns) */
+ unsigned int clockToDataOutMinus1_RoP; /* RoP right of point (measured in ns) */
+ unsigned int clockToDataOutMinus2_LoP; /* LoP left of point (measured in ns) */
+ unsigned int clockToDataOutMinus2_RoP; /* RoP right of point (measured in ns) */
+
+ unsigned int minimumCycleTimeAtMaxCasLatancy_LoP; /* LoP left of point (measured in ns) */
+ unsigned int minimumCycleTimeAtMaxCasLatancy_RoP; /* RoP right of point (measured in ns) */
+
+ unsigned int minimumCycleTimeAtMaxCasLatancyMinus1_LoP; /* LoP left of point (measured in ns) */
+ unsigned int minimumCycleTimeAtMaxCasLatancyMinus1_RoP; /* RoP right of point (measured in ns) */
+
+ unsigned int minimumCycleTimeAtMaxCasLatancyMinus2_LoP; /* LoP left of point (measured in ns) */
+ unsigned int minimumCycleTimeAtMaxCasLatancyMinus2_RoP; /* RoP right of point (measured in ns) */
+
+ /* Parameters calculated from
+ the extracted DIMM information */
+ unsigned int size;
+ unsigned int deviceDensity; /* 16,64,128,256 or 512 Mbit */
+ unsigned int numberOfDevices;
+ uchar drb_size; /* DRAM size in n*64Mbit */
+ uchar slot; /* Slot Number this module is inserted in */
+ uchar spd_raw_data[128]; /* Content of SPD-EEPROM copied 1:1 */
+#ifdef DEBUG
+ uchar manufactura[8]; /* Content of SPD-EEPROM Byte 64-71 */
+ uchar modul_id[18]; /* Content of SPD-EEPROM Byte 73-90 */
+ uchar vendor_data[27]; /* Content of SPD-EEPROM Byte 99-125 */
+ unsigned long modul_serial_no; /* Content of SPD-EEPROM Byte 95-98 */
+ unsigned int manufac_date; /* Content of SPD-EEPROM Byte 93-94 */
+ unsigned int modul_revision; /* Content of SPD-EEPROM Byte 91-92 */
+ uchar manufac_place; /* Content of SPD-EEPROM Byte 72 */
+
+#endif
+} AUX_MEM_DIMM_INFO;
+
+
+/*
+ * translate ns.ns/10 coding of SPD timing values
+ * into 10 ps unit values
+ */
+static inline unsigned short NS10to10PS (unsigned char spd_byte)
+{
+ unsigned short ns, ns10;
+
+ /* isolate upper nibble */
+ ns = (spd_byte >> 4) & 0x0F;
+ /* isolate lower nibble */
+ ns10 = (spd_byte & 0x0F);
+
+ return (ns * 100 + ns10 * 10);
+}
+
+/*
+ * translate ns coding of SPD timing values
+ * into 10 ps unit values
+ */
+static inline unsigned short NSto10PS (unsigned char spd_byte)
+{
+ return (spd_byte * 100);
+}
+
+/* This code reads the SPD chip on the sdram and populates
+ * the array which is passed in with the relevant information */
+/* static int check_dimm(uchar slot, AUX_MEM_DIMM_INFO *info) */
+static int check_dimm (uchar slot, AUX_MEM_DIMM_INFO * dimmInfo)
+{
+ DECLARE_GLOBAL_DATA_PTR;
+
+ unsigned long spd_checksum;
+
+#ifdef ZUMA_NTL
+ /* zero all the values */
+ memset (info, 0, sizeof (*info));
+
+/*
+ if (!slot) {
+ info->slot = 0;
+ info->banks = 1;
+ info->registered = 0;
+ info->drb_size = 16;*/ /* 16 - 256MBit, 32 - 512MBit */
+/* info->tpar = 3;
+ info->tras_clocks = 5;
+ info->burst_len = 4;
+*/
+#ifdef CONFIG_MV64460_ECC
+ /* check for ECC/parity [0 = none, 1 = parity, 2 = ecc] */
+ dimmInfo->errorCheckType = 2;
+/* info->ecc = 2;*/
+#endif
+}
+
+return 0;
+
+#else
+ uchar addr = slot == 0 ? DIMM0_I2C_ADDR : DIMM1_I2C_ADDR;
+ int ret;
+ unsigned int i, j, density = 1, devicesForErrCheck = 0;
+
+#ifdef DEBUG
+ unsigned int k;
+#endif
+ unsigned int rightOfPoint = 0, leftOfPoint = 0, mult, div, time_tmp;
+ int sign = 1, shift, maskLeftOfPoint, maskRightOfPoint;
+ uchar supp_cal, cal_val;
+ ulong memclk, tmemclk;
+ ulong tmp;
+ uchar trp_clocks = 0, trcd_clocks, tras_clocks, trrd_clocks;
+ uchar data[128];
+
+ memclk = gd->bus_clk;
+ tmemclk = 1000000000 / (memclk / 100); /* in 10 ps units */
+
+ DP (puts ("before i2c read\n"));
+
+ ret = i2c_read (addr, 0, 1, data, 128);
+
+ DP (puts ("after i2c read\n"));
+
+ /* zero all the values */
+ memset (dimmInfo, 0, sizeof (*dimmInfo));
+
+ /* copy the SPD content 1:1 into the dimmInfo structure */
+ for (i = 0; i <= 127; i++) {
+ dimmInfo->spd_raw_data[i] = data[i];
+ }
+
+ if (ret) {
+ DP (printf ("No DIMM in slot %d [err = %x]\n", slot, ret));
+ return 0;
+ } else
+ dimmInfo->slot = slot; /* start to fill up dimminfo for this "slot" */
+
+#ifdef CFG_DISPLAY_DIMM_SPD_CONTENT
+
+ for (i = 0; i <= 127; i++) {
+ printf ("SPD-EEPROM Byte %3d = %3x (%3d)\n", i, data[i],
+ data[i]);
+ }
+
+#endif
+#ifdef DEBUG
+/* find Manufactura of Dimm Module */
+ for (i = 0; i < sizeof (dimmInfo->manufactura); i++) {
+ dimmInfo->manufactura[i] = data[64 + i];
+ }
+ printf ("\nThis RAM-Module is produced by: %s\n",
+ dimmInfo->manufactura);
+
+/* find Manul-ID of Dimm Module */
+ for (i = 0; i < sizeof (dimmInfo->modul_id); i++) {
+ dimmInfo->modul_id[i] = data[73 + i];
+ }
+ printf ("The Module-ID of this RAM-Module is: %s\n",
+ dimmInfo->modul_id);
+
+/* find Vendor-Data of Dimm Module */
+ for (i = 0; i < sizeof (dimmInfo->vendor_data); i++) {
+ dimmInfo->vendor_data[i] = data[99 + i];
+ }
+ printf ("Vendor Data of this RAM-Module is: %s\n",
+ dimmInfo->vendor_data);
+
+/* find modul_serial_no of Dimm Module */
+ dimmInfo->modul_serial_no = (*((unsigned long *) (&data[95])));
+ printf ("Serial No. of this RAM-Module is: %ld (%lx)\n",
+ dimmInfo->modul_serial_no, dimmInfo->modul_serial_no);
+
+/* find Manufac-Data of Dimm Module */
+ dimmInfo->manufac_date = (*((unsigned int *) (&data[93])));
+ printf ("Manufactoring Date of this RAM-Module is: %d.%d\n", data[93], data[94]); /*dimmInfo->manufac_date */
+
+/* find modul_revision of Dimm Module */
+ dimmInfo->modul_revision = (*((unsigned int *) (&data[91])));
+ printf ("Module Revision of this RAM-Module is: %d.%d\n", data[91], data[92]); /* dimmInfo->modul_revision */
+
+/* find manufac_place of Dimm Module */
+ dimmInfo->manufac_place = (*((unsigned char *) (&data[72])));
+ printf ("manufac_place of this RAM-Module is: %d\n",
+ dimmInfo->manufac_place);
+
+#endif
+
+/*------------------------------------------------------------------------------------------------------------------------------*/
+/* calculate SPD checksum */
+/*------------------------------------------------------------------------------------------------------------------------------*/
+ spd_checksum = 0;
+
+ for (i = 0; i <= 62; i++) {
+ spd_checksum += data[i];
+ }
+
+ if ((spd_checksum & 0xff) != data[63]) {
+ printf ("### Error in SPD Checksum !!! Is_value: %2x should value %2x\n", (unsigned int) (spd_checksum & 0xff), data[63]);
+ hang ();
+ }
+
+ else
+ printf ("SPD Checksum ok!\n");
+
+
+/*------------------------------------------------------------------------------------------------------------------------------*/
+ for (i = 2; i <= 35; i++) {
+ switch (i) {
+ case 2: /* Memory type (DDR / SDRAM) */
+ dimmInfo->memoryType = (data[i] == 0x7) ? DDR : SDRAM;
+#ifdef DEBUG
+ if (dimmInfo->memoryType == 0)
+ DP (printf
+ ("Dram_type in slot %d is: SDRAM\n",
+ dimmInfo->slot));
+ if (dimmInfo->memoryType == 1)
+ DP (printf
+ ("Dram_type in slot %d is: DDRAM\n",
+ dimmInfo->slot));
+#endif
+ break;
+/*------------------------------------------------------------------------------------------------------------------------------*/
+
+ case 3: /* Number Of Row Addresses */
+ dimmInfo->numOfRowAddresses = data[i];
+ DP (printf
+ ("Module Number of row addresses: %d\n",
+ dimmInfo->numOfRowAddresses));
+ break;
+/*------------------------------------------------------------------------------------------------------------------------------*/
+
+ case 4: /* Number Of Column Addresses */
+ dimmInfo->numOfColAddresses = data[i];
+ DP (printf
+ ("Module Number of col addresses: %d\n",
+ dimmInfo->numOfColAddresses));
+ break;
+/*------------------------------------------------------------------------------------------------------------------------------*/
+
+ case 5: /* Number Of Module Banks */
+ dimmInfo->numOfModuleBanks = data[i];
+ DP (printf
+ ("Number of Banks on Mod. : %d\n",
+ dimmInfo->numOfModuleBanks));
+ break;
+/*------------------------------------------------------------------------------------------------------------------------------*/
+
+ case 6: /* Data Width */
+ dimmInfo->dataWidth = data[i];
+ DP (printf
+ ("Module Data Width: %d\n",
+ dimmInfo->dataWidth));
+ break;
+/*------------------------------------------------------------------------------------------------------------------------------*/
+
+ case 8: /* Voltage Interface */
+ switch (data[i]) {
+ case 0x0:
+ dimmInfo->voltageInterface = TTL_5V_TOLERANT;
+ DP (printf
+ ("Module is TTL_5V_TOLERANT\n"));
+ break;
+ case 0x1:
+ dimmInfo->voltageInterface = LVTTL;
+ DP (printf
+ ("Module is LVTTL\n"));
+ break;
+ case 0x2:
+ dimmInfo->voltageInterface = HSTL_1_5V;
+ DP (printf
+ ("Module is TTL_5V_TOLERANT\n"));
+ break;
+ case 0x3:
+ dimmInfo->voltageInterface = SSTL_3_3V;
+ DP (printf
+ ("Module is HSTL_1_5V\n"));
+ break;
+ case 0x4:
+ dimmInfo->voltageInterface = SSTL_2_5V;
+ DP (printf
+ ("Module is SSTL_2_5V\n"));
+ break;
+ default:
+ dimmInfo->voltageInterface = VOLTAGE_UNKNOWN;
+ DP (printf
+ ("Module is VOLTAGE_UNKNOWN\n"));
+ break;
+ }
+ break;
+/*------------------------------------------------------------------------------------------------------------------------------*/
+
+ case 9: /* Minimum Cycle Time At Max CasLatancy */
+ shift = (dimmInfo->memoryType == DDR) ? 4 : 2;
+ mult = (dimmInfo->memoryType == DDR) ? 10 : 25;
+ maskLeftOfPoint =
+ (dimmInfo->memoryType == DDR) ? 0xf0 : 0xfc;
+ maskRightOfPoint =
+ (dimmInfo->memoryType == DDR) ? 0xf : 0x03;
+ leftOfPoint = (data[i] & maskLeftOfPoint) >> shift;
+ rightOfPoint = (data[i] & maskRightOfPoint) * mult;
+ dimmInfo->minimumCycleTimeAtMaxCasLatancy_LoP =
+ leftOfPoint;
+ dimmInfo->minimumCycleTimeAtMaxCasLatancy_RoP =
+ rightOfPoint;
+ DP (printf
+ ("Minimum Cycle Time At Max CasLatancy: %d.%d [ns]\n",
+ leftOfPoint, rightOfPoint));
+ break;
+/*------------------------------------------------------------------------------------------------------------------------------*/
+
+ case 10: /* Clock To Data Out */
+ div = (dimmInfo->memoryType == DDR) ? 100 : 10;
+ time_tmp =
+ (((data[i] & 0xf0) >> 4) * 10) +
+ ((data[i] & 0x0f));
+ leftOfPoint = time_tmp / div;
+ rightOfPoint = time_tmp % div;
+ dimmInfo->clockToDataOut_LoP = leftOfPoint;
+ dimmInfo->clockToDataOut_RoP = rightOfPoint;
+ DP (printf ("Clock To Data Out: %d.%2d [ns]\n", leftOfPoint, rightOfPoint)); /*dimmInfo->clockToDataOut */
+ break;
+/*------------------------------------------------------------------------------------------------------------------------------*/
+
+/*#ifdef CONFIG_ECC */
+ case 11: /* Error Check Type */
+ dimmInfo->errorCheckType = data[i];
+ DP (printf
+ ("Error Check Type (0=NONE): %d\n",
+ dimmInfo->errorCheckType));
+ break;
+/* #endif */
+/*------------------------------------------------------------------------------------------------------------------------------*/
+
+ case 12: /* Refresh Interval */
+ dimmInfo->RefreshInterval = data[i];
+ DP (printf
+ ("RefreshInterval (80= Self refresh Normal, 15.625us) : %x\n",
+ dimmInfo->RefreshInterval));
+ break;
+/*------------------------------------------------------------------------------------------------------------------------------*/
+
+ case 13: /* Sdram Width */
+ dimmInfo->sdramWidth = data[i];
+ DP (printf
+ ("Sdram Width: %d\n",
+ dimmInfo->sdramWidth));
+ break;
+/*------------------------------------------------------------------------------------------------------------------------------*/
+
+ case 14: /* Error Check Data Width */
+ dimmInfo->errorCheckDataWidth = data[i];
+ DP (printf
+ ("Error Check Data Width: %d\n",
+ dimmInfo->errorCheckDataWidth));
+ break;
+/*------------------------------------------------------------------------------------------------------------------------------*/
+
+ case 15: /* Minimum Clock Delay */
+ dimmInfo->minClkDelay = data[i];
+ DP (printf
+ ("Minimum Clock Delay: %d\n",
+ dimmInfo->minClkDelay));
+ break;
+/*------------------------------------------------------------------------------------------------------------------------------*/
+
+ case 16: /* Burst Length Supported */
+ /******-******-******-*******
+ * bit3 | bit2 | bit1 | bit0 *
+ *******-******-******-*******
+ burst length = * 8 | 4 | 2 | 1 *
+ *****************************
+
+ If for example bit0 and bit2 are set, the burst
+ length supported are 1 and 4. */
+
+ dimmInfo->burstLengthSupported = data[i];
+#ifdef DEBUG
+ DP (printf
+ ("Burst Length Supported: "));
+ if (dimmInfo->burstLengthSupported & 0x01)
+ DP (printf ("1, "));
+ if (dimmInfo->burstLengthSupported & 0x02)
+ DP (printf ("2, "));
+ if (dimmInfo->burstLengthSupported & 0x04)
+ DP (printf ("4, "));
+ if (dimmInfo->burstLengthSupported & 0x08)
+ DP (printf ("8, "));
+ DP (printf (" Bit \n"));
+#endif
+ break;
+/*------------------------------------------------------------------------------------------------------------------------------*/
+
+ case 17: /* Number Of Banks On Each Device */
+ dimmInfo->numOfBanksOnEachDevice = data[i];
+ DP (printf
+ ("Number Of Banks On Each Chip: %d\n",
+ dimmInfo->numOfBanksOnEachDevice));
+ break;
+/*------------------------------------------------------------------------------------------------------------------------------*/
+
+ case 18: /* Suported Cas Latencies */
+
+ /* DDR:
+ *******-******-******-******-******-******-******-*******
+ * bit7 | bit6 | bit5 | bit4 | bit3 | bit2 | bit1 | bit0 *
+ *******-******-******-******-******-******-******-*******
+ CAS = * TBD | TBD | 3.5 | 3 | 2.5 | 2 | 1.5 | 1 *
+ *********************************************************
+ SDRAM:
+ *******-******-******-******-******-******-******-*******
+ * bit7 | bit6 | bit5 | bit4 | bit3 | bit2 | bit1 | bit0 *
+ *******-******-******-******-******-******-******-*******
+ CAS = * TBD | 7 | 6 | 5 | 4 | 3 | 2 | 1 *
+ ********************************************************/
+ dimmInfo->suportedCasLatencies = data[i];
+#ifdef DEBUG
+ DP (printf
+ ("Suported Cas Latencies: (CL) "));
+ if (dimmInfo->memoryType == 0) { /* SDRAM */
+ for (k = 0; k <= 7; k++) {
+ if (dimmInfo->
+ suportedCasLatencies & (1 << k))
+ DP (printf
+ ("%d, ",
+ k + 1));
+ }
+
+ } else { /* DDR-RAM */
+
+ if (dimmInfo->suportedCasLatencies & 1)
+ DP (printf ("1, "));
+ if (dimmInfo->suportedCasLatencies & 2)
+ DP (printf ("1.5, "));
+ if (dimmInfo->suportedCasLatencies & 4)
+ DP (printf ("2, "));
+ if (dimmInfo->suportedCasLatencies & 8)
+ DP (printf ("2.5, "));
+ if (dimmInfo->suportedCasLatencies & 16)
+ DP (printf ("3, "));
+ if (dimmInfo->suportedCasLatencies & 32)
+ DP (printf ("3.5, "));
+
+ }
+ DP (printf ("\n"));
+#endif
+ /* Calculating MAX CAS latency */
+ for (j = 7; j > 0; j--) {
+ if (((dimmInfo->
+ suportedCasLatencies >> j) & 0x1) ==
+ 1) {
+ switch (dimmInfo->memoryType) {
+ case DDR:
+ /* CAS latency 1, 1.5, 2, 2.5, 3, 3.5 */
+ switch (j) {
+ case 7:
+ DP (printf
+ ("Max. Cas Latencies (DDR): ERROR !!!\n"));
+ dimmInfo->
+ maxClSupported_DDR
+ =
+ DDR_CL_FAULT;
+ hang ();
+ break;
+ case 6:
+ DP (printf
+ ("Max. Cas Latencies (DDR): ERROR !!!\n"));
+ dimmInfo->
+ maxClSupported_DDR
+ =
+ DDR_CL_FAULT;
+ hang ();
+ break;
+ case 5:
+ DP (printf
+ ("Max. Cas Latencies (DDR): 3.5 clk's\n"));
+ dimmInfo->
+ maxClSupported_DDR
+ = DDR_CL_3_5;
+ break;
+ case 4:
+ DP (printf
+ ("Max. Cas Latencies (DDR): 3 clk's \n"));
+ dimmInfo->
+ maxClSupported_DDR
+ = DDR_CL_3;
+ break;
+ case 3:
+ DP (printf
+ ("Max. Cas Latencies (DDR): 2.5 clk's \n"));
+ dimmInfo->
+ maxClSupported_DDR
+ = DDR_CL_2_5;
+ break;
+ case 2:
+ DP (printf
+ ("Max. Cas Latencies (DDR): 2 clk's \n"));
+ dimmInfo->
+ maxClSupported_DDR
+ = DDR_CL_2;
+ break;
+ case 1:
+ DP (printf
+ ("Max. Cas Latencies (DDR): 1.5 clk's \n"));
+ dimmInfo->
+ maxClSupported_DDR
+ = DDR_CL_1_5;
+ break;
+ }
+
+ /* ronen - in case we have a DIMM with minimumCycleTimeAtMaxCasLatancy
+ lower then our SDRAM cycle count, we won't be able to support this CAL
+ and we will have to use lower CAL. (minus - means from 3.0 to 2.5) */
+ if ((dimmInfo->
+ minimumCycleTimeAtMaxCasLatancy_LoP
+ <
+ CFG_DDR_SDRAM_CYCLE_COUNT_LOP)
+ ||
+ ((dimmInfo->
+ minimumCycleTimeAtMaxCasLatancy_LoP
+ ==
+ CFG_DDR_SDRAM_CYCLE_COUNT_LOP)
+ && (dimmInfo->
+ minimumCycleTimeAtMaxCasLatancy_RoP
+ <
+ CFG_DDR_SDRAM_CYCLE_COUNT_ROP)))
+ {
+ dimmInfo->
+ maxClSupported_DDR
+ =
+ dimmInfo->
+ maxClSupported_DDR
+ >> 1;
+ DP (printf
+ ("*** Change actual Cas Latencies cause of minimumCycleTime n"));
+ }
+ /* ronen - checkif the Dimm frequency compared to the Sysclock. */
+ if ((dimmInfo->
+ minimumCycleTimeAtMaxCasLatancy_LoP
+ >
+ CFG_DDR_SDRAM_CYCLE_COUNT_LOP)
+ ||
+ ((dimmInfo->
+ minimumCycleTimeAtMaxCasLatancy_LoP
+ ==
+ CFG_DDR_SDRAM_CYCLE_COUNT_LOP)
+ && (dimmInfo->
+ minimumCycleTimeAtMaxCasLatancy_RoP
+ >
+ CFG_DDR_SDRAM_CYCLE_COUNT_ROP)))
+ {
+ printf ("*********************************************************\n");
+ printf ("*** sysClock is higher than SDRAM's allowed frequency ***\n");
+ printf ("*********************************************************\n");
+ hang ();
+ }
+
+ dimmInfo->
+ maxCASlatencySupported_LoP
+ =
+ 1 +
+ (int) (5 * j / 10);
+ if (((5 * j) % 10) != 0)
+ dimmInfo->
+ maxCASlatencySupported_RoP
+ = 5;
+ else
+ dimmInfo->
+ maxCASlatencySupported_RoP
+ = 0;
+ DP (printf
+ ("Max. Cas Latencies (DDR LoP.RoP Notation): %d.%d \n",
+ dimmInfo->
+ maxCASlatencySupported_LoP,
+ dimmInfo->
+ maxCASlatencySupported_RoP));
+ break;
+ case SDRAM:
+ /* CAS latency 1, 2, 3, 4, 5, 6, 7 */
+ dimmInfo->maxClSupported_SD = j; /* Cas Latency DDR-RAM Coded */
+ DP (printf
+ ("Max. Cas Latencies (SD): %d\n",
+ dimmInfo->
+ maxClSupported_SD));
+ dimmInfo->
+ maxCASlatencySupported_LoP
+ = j;
+ dimmInfo->
+ maxCASlatencySupported_RoP
+ = 0;
+ DP (printf
+ ("Max. Cas Latencies (DDR LoP.RoP Notation): %d.%d \n",
+ dimmInfo->
+ maxCASlatencySupported_LoP,
+ dimmInfo->
+ maxCASlatencySupported_RoP));
+ break;
+ }
+ break;
+ }
+ }
+ break;
+/*------------------------------------------------------------------------------------------------------------------------------*/
+
+ case 21: /* Buffered Address And Control Inputs */
+ DP (printf ("\nModul Attributes (SPD Byte 21): \n"));
+ dimmInfo->bufferedAddrAndControlInputs =
+ data[i] & BIT0;
+ dimmInfo->registeredAddrAndControlInputs =
+ (data[i] & BIT1) >> 1;
+ dimmInfo->onCardPLL = (data[i] & BIT2) >> 2;
+ dimmInfo->bufferedDQMBinputs = (data[i] & BIT3) >> 3;
+ dimmInfo->registeredDQMBinputs =
+ (data[i] & BIT4) >> 4;
+ dimmInfo->differentialClockInput =
+ (data[i] & BIT5) >> 5;
+ dimmInfo->redundantRowAddressing =
+ (data[i] & BIT6) >> 6;
+#ifdef DEBUG
+ if (dimmInfo->bufferedAddrAndControlInputs == 1)
+ DP (printf
+ (" - Buffered Address/Control Input: Yes \n"));
+ else
+ DP (printf
+ (" - Buffered Address/Control Input: No \n"));
+
+ if (dimmInfo->registeredAddrAndControlInputs == 1)
+ DP (printf
+ (" - Registered Address/Control Input: Yes \n"));
+ else
+ DP (printf
+ (" - Registered Address/Control Input: No \n"));
+
+ if (dimmInfo->onCardPLL == 1)
+ DP (printf
+ (" - On-Card PLL (clock): Yes \n"));
+ else
+ DP (printf
+ (" - On-Card PLL (clock): No \n"));
+
+ if (dimmInfo->bufferedDQMBinputs == 1)
+ DP (printf
+ (" - Bufferd DQMB Inputs: Yes \n"));
+ else
+ DP (printf
+ (" - Bufferd DQMB Inputs: No \n"));
+
+ if (dimmInfo->registeredDQMBinputs == 1)
+ DP (printf
+ (" - Registered DQMB Inputs: Yes \n"));
+ else
+ DP (printf
+ (" - Registered DQMB Inputs: No \n"));
+
+ if (dimmInfo->differentialClockInput == 1)
+ DP (printf
+ (" - Differential Clock Input: Yes \n"));
+ else
+ DP (printf
+ (" - Differential Clock Input: No \n"));
+
+ if (dimmInfo->redundantRowAddressing == 1)
+ DP (printf
+ (" - redundant Row Addressing: Yes \n"));
+ else
+ DP (printf
+ (" - redundant Row Addressing: No \n"));
+
+#endif
+ break;
+/*------------------------------------------------------------------------------------------------------------------------------*/
+
+ case 22: /* Suported AutoPreCharge */
+ DP (printf ("\nModul Attributes (SPD Byte 22): \n"));
+ dimmInfo->suportedEarlyRasPreCharge = data[i] & BIT0;
+ dimmInfo->suportedAutoPreCharge =
+ (data[i] & BIT1) >> 1;
+ dimmInfo->suportedPreChargeAll =
+ (data[i] & BIT2) >> 2;
+ dimmInfo->suportedWrite1ReadBurst =
+ (data[i] & BIT3) >> 3;
+ dimmInfo->suported5PercentLowVCC =
+ (data[i] & BIT4) >> 4;
+ dimmInfo->suported5PercentUpperVCC =
+ (data[i] & BIT5) >> 5;
+#ifdef DEBUG
+ if (dimmInfo->suportedEarlyRasPreCharge == 1)
+ DP (printf
+ (" - Early Ras Precharge: Yes \n"));
+ else
+ DP (printf
+ (" - Early Ras Precharge: No \n"));
+
+ if (dimmInfo->suportedAutoPreCharge == 1)
+ DP (printf
+ (" - AutoPreCharge: Yes \n"));
+ else
+ DP (printf
+ (" - AutoPreCharge: No \n"));
+
+ if (dimmInfo->suportedPreChargeAll == 1)
+ DP (printf
+ (" - Precharge All: Yes \n"));
+ else
+ DP (printf
+ (" - Precharge All: No \n"));
+
+ if (dimmInfo->suportedWrite1ReadBurst == 1)
+ DP (printf
+ (" - Write 1/ReadBurst: Yes \n"));
+ else
+ DP (printf
+ (" - Write 1/ReadBurst: No \n"));
+
+ if (dimmInfo->suported5PercentLowVCC == 1)
+ DP (printf
+ (" - lower VCC tolerance: 5 Percent \n"));
+ else
+ DP (printf
+ (" - lower VCC tolerance: 10 Percent \n"));
+
+ if (dimmInfo->suported5PercentUpperVCC == 1)
+ DP (printf
+ (" - upper VCC tolerance: 5 Percent \n"));
+ else
+ DP (printf
+ (" - upper VCC tolerance: 10 Percent \n"));
+
+#endif
+ break;
+/*------------------------------------------------------------------------------------------------------------------------------*/
+
+ case 23: /* Minimum Cycle Time At Maximum Cas Latancy Minus 1 (2nd highest CL) */
+ shift = (dimmInfo->memoryType == DDR) ? 4 : 2;
+ mult = (dimmInfo->memoryType == DDR) ? 10 : 25;
+ maskLeftOfPoint =
+ (dimmInfo->memoryType == DDR) ? 0xf0 : 0xfc;
+ maskRightOfPoint =
+ (dimmInfo->memoryType == DDR) ? 0xf : 0x03;
+ leftOfPoint = (data[i] & maskLeftOfPoint) >> shift;
+ rightOfPoint = (data[i] & maskRightOfPoint) * mult;
+ dimmInfo->minimumCycleTimeAtMaxCasLatancyMinus1_LoP =
+ leftOfPoint;
+ dimmInfo->minimumCycleTimeAtMaxCasLatancyMinus1_RoP =
+ rightOfPoint;
+ DP (printf ("Minimum Cycle Time At 2nd highest CasLatancy (0 = Not supported): %d.%d [ns]\n", leftOfPoint, rightOfPoint)); /*dimmInfo->minimumCycleTimeAtMaxCasLatancy */
+ break;
+/*------------------------------------------------------------------------------------------------------------------------------*/
+
+ case 24: /* Clock To Data Out 2nd highest Cas Latency Value */
+ div = (dimmInfo->memoryType == DDR) ? 100 : 10;
+ time_tmp =
+ (((data[i] & 0xf0) >> 4) * 10) +
+ ((data[i] & 0x0f));
+ leftOfPoint = time_tmp / div;
+ rightOfPoint = time_tmp % div;
+ dimmInfo->clockToDataOutMinus1_LoP = leftOfPoint;
+ dimmInfo->clockToDataOutMinus1_RoP = rightOfPoint;
+ DP (printf
+ ("Clock To Data Out (2nd CL value): %d.%2d [ns]\n",
+ leftOfPoint, rightOfPoint));
+ break;
+/*------------------------------------------------------------------------------------------------------------------------------*/
+
+ case 25: /* Minimum Cycle Time At Maximum Cas Latancy Minus 2 (3rd highest CL) */
+ shift = (dimmInfo->memoryType == DDR) ? 4 : 2;
+ mult = (dimmInfo->memoryType == DDR) ? 10 : 25;
+ maskLeftOfPoint =
+ (dimmInfo->memoryType == DDR) ? 0xf0 : 0xfc;
+ maskRightOfPoint =
+ (dimmInfo->memoryType == DDR) ? 0xf : 0x03;
+ leftOfPoint = (data[i] & maskLeftOfPoint) >> shift;
+ rightOfPoint = (data[i] & maskRightOfPoint) * mult;
+ dimmInfo->minimumCycleTimeAtMaxCasLatancyMinus2_LoP =
+ leftOfPoint;
+ dimmInfo->minimumCycleTimeAtMaxCasLatancyMinus2_RoP =
+ rightOfPoint;
+ DP (printf ("Minimum Cycle Time At 3rd highest CasLatancy (0 = Not supported): %d.%d [ns]\n", leftOfPoint, rightOfPoint)); /*dimmInfo->minimumCycleTimeAtMaxCasLatancy */
+ break;
+/*------------------------------------------------------------------------------------------------------------------------------*/
+
+ case 26: /* Clock To Data Out 3rd highest Cas Latency Value */
+ div = (dimmInfo->memoryType == DDR) ? 100 : 10;
+ time_tmp =
+ (((data[i] & 0xf0) >> 4) * 10) +
+ ((data[i] & 0x0f));
+ leftOfPoint = time_tmp / div;
+ rightOfPoint = time_tmp % div;
+ dimmInfo->clockToDataOutMinus2_LoP = leftOfPoint;
+ dimmInfo->clockToDataOutMinus2_RoP = rightOfPoint;
+ DP (printf
+ ("Clock To Data Out (3rd CL value): %d.%2d [ns]\n",
+ leftOfPoint, rightOfPoint));
+ break;
+/*------------------------------------------------------------------------------------------------------------------------------*/
+
+ case 27: /* Minimum Row Precharge Time */
+ shift = (dimmInfo->memoryType == DDR) ? 2 : 0;
+ maskLeftOfPoint =
+ (dimmInfo->memoryType == DDR) ? 0xfc : 0xff;
+ maskRightOfPoint =
+ (dimmInfo->memoryType == DDR) ? 0x03 : 0x00;
+ leftOfPoint = ((data[i] & maskLeftOfPoint) >> shift);
+ rightOfPoint = (data[i] & maskRightOfPoint) * 25;
+
+ dimmInfo->minRowPrechargeTime = ((leftOfPoint * 100) + rightOfPoint); /* measured in n times 10ps Intervals */
+ trp_clocks =
+ (dimmInfo->minRowPrechargeTime +
+ (tmemclk - 1)) / tmemclk;
+ DP (printf
+ ("*** 1 clock cycle = %ld 10ps intervalls = %ld.%ld ns****\n",
+ tmemclk, tmemclk / 100, tmemclk % 100));
+ DP (printf
+ ("Minimum Row Precharge Time [ns]: %d.%2d = in Clk cycles %d\n",
+ leftOfPoint, rightOfPoint, trp_clocks));
+ break;
+/*------------------------------------------------------------------------------------------------------------------------------*/
+
+ case 28: /* Minimum Row Active to Row Active Time */
+ shift = (dimmInfo->memoryType == DDR) ? 2 : 0;
+ maskLeftOfPoint =
+ (dimmInfo->memoryType == DDR) ? 0xfc : 0xff;
+ maskRightOfPoint =
+ (dimmInfo->memoryType == DDR) ? 0x03 : 0x00;
+ leftOfPoint = ((data[i] & maskLeftOfPoint) >> shift);
+ rightOfPoint = (data[i] & maskRightOfPoint) * 25;
+
+ dimmInfo->minRowActiveRowActiveDelay = ((leftOfPoint * 100) + rightOfPoint); /* measured in 100ns Intervals */
+ trrd_clocks =
+ (dimmInfo->minRowActiveRowActiveDelay +
+ (tmemclk - 1)) / tmemclk;
+ DP (printf
+ ("Minimum Row Active -To- Row Active Delay [ns]: %d.%2d = in Clk cycles %d\n",
+ leftOfPoint, rightOfPoint, trp_clocks));
+ break;
+/*------------------------------------------------------------------------------------------------------------------------------*/
+
+ case 29: /* Minimum Ras-To-Cas Delay */
+ shift = (dimmInfo->memoryType == DDR) ? 2 : 0;
+ maskLeftOfPoint =
+ (dimmInfo->memoryType == DDR) ? 0xfc : 0xff;
+ maskRightOfPoint =
+ (dimmInfo->memoryType == DDR) ? 0x03 : 0x00;
+ leftOfPoint = ((data[i] & maskLeftOfPoint) >> shift);
+ rightOfPoint = (data[i] & maskRightOfPoint) * 25;
+
+ dimmInfo->minRowActiveRowActiveDelay = ((leftOfPoint * 100) + rightOfPoint); /* measured in 100ns Intervals */
+ trcd_clocks =
+ (dimmInfo->minRowActiveRowActiveDelay +
+ (tmemclk - 1)) / tmemclk;
+ DP (printf
+ ("Minimum Ras-To-Cas Delay [ns]: %d.%2d = in Clk cycles %d\n",
+ leftOfPoint, rightOfPoint, trp_clocks));
+ break;
+/*------------------------------------------------------------------------------------------------------------------------------*/
+
+ case 30: /* Minimum Ras Pulse Width */
+ dimmInfo->minRasPulseWidth = data[i];
+ tras_clocks =
+ (NSto10PS (data[i]) +
+ (tmemclk - 1)) / tmemclk;
+ DP (printf
+ ("Minimum Ras Pulse Width [ns]: %d = in Clk cycles %d\n",
+ dimmInfo->minRasPulseWidth, tras_clocks));
+
+ break;
+/*------------------------------------------------------------------------------------------------------------------------------*/
+
+ case 31: /* Module Bank Density */
+ dimmInfo->moduleBankDensity = data[i];
+ DP (printf
+ ("Module Bank Density: %d\n",
+ dimmInfo->moduleBankDensity));
+#ifdef DEBUG
+ DP (printf
+ ("*** Offered Densities (more than 1 = Multisize-Module): "));
+ {
+ if (dimmInfo->moduleBankDensity & 1)
+ DP (printf ("4MB, "));
+ if (dimmInfo->moduleBankDensity & 2)
+ DP (printf ("8MB, "));
+ if (dimmInfo->moduleBankDensity & 4)
+ DP (printf ("16MB, "));
+ if (dimmInfo->moduleBankDensity & 8)
+ DP (printf ("32MB, "));
+ if (dimmInfo->moduleBankDensity & 16)
+ DP (printf ("64MB, "));
+ if (dimmInfo->moduleBankDensity & 32)
+ DP (printf ("128MB, "));
+ if ((dimmInfo->moduleBankDensity & 64)
+ || (dimmInfo->moduleBankDensity & 128)) {
+ DP (printf ("ERROR, "));
+ hang ();
+ }
+ }
+ DP (printf ("\n"));
+#endif
+ break;
+/*------------------------------------------------------------------------------------------------------------------------------*/
+
+ case 32: /* Address And Command Setup Time (measured in ns/1000) */
+ sign = 1;
+ switch (dimmInfo->memoryType) {
+ case DDR:
+ time_tmp =
+ (((data[i] & 0xf0) >> 4) * 10) +
+ ((data[i] & 0x0f));
+ leftOfPoint = time_tmp / 100;
+ rightOfPoint = time_tmp % 100;
+ break;
+ case SDRAM:
+ leftOfPoint = (data[i] & 0xf0) >> 4;
+ if (leftOfPoint > 7) {
+ leftOfPoint = data[i] & 0x70 >> 4;
+ sign = -1;
+ }
+ rightOfPoint = (data[i] & 0x0f);
+ break;
+ }
+ dimmInfo->addrAndCommandSetupTime =
+ (leftOfPoint * 100 + rightOfPoint) * sign;
+ DP (printf
+ ("Address And Command Setup Time [ns]: %d.%d\n",
+ sign * leftOfPoint, rightOfPoint));
+ break;
+/*------------------------------------------------------------------------------------------------------------------------------*/
+
+ case 33: /* Address And Command Hold Time */
+ sign = 1;
+ switch (dimmInfo->memoryType) {
+ case DDR:
+ time_tmp =
+ (((data[i] & 0xf0) >> 4) * 10) +
+ ((data[i] & 0x0f));
+ leftOfPoint = time_tmp / 100;
+ rightOfPoint = time_tmp % 100;
+ break;
+ case SDRAM:
+ leftOfPoint = (data[i] & 0xf0) >> 4;
+ if (leftOfPoint > 7) {
+ leftOfPoint = data[i] & 0x70 >> 4;
+ sign = -1;
+ }
+ rightOfPoint = (data[i] & 0x0f);
+ break;
+ }
+ dimmInfo->addrAndCommandHoldTime =
+ (leftOfPoint * 100 + rightOfPoint) * sign;
+ DP (printf
+ ("Address And Command Hold Time [ns]: %d.%d\n",
+ sign * leftOfPoint, rightOfPoint));
+ break;
+/*------------------------------------------------------------------------------------------------------------------------------*/
+
+ case 34: /* Data Input Setup Time */
+ sign = 1;
+ switch (dimmInfo->memoryType) {
+ case DDR:
+ time_tmp =
+ (((data[i] & 0xf0) >> 4) * 10) +
+ ((data[i] & 0x0f));
+ leftOfPoint = time_tmp / 100;
+ rightOfPoint = time_tmp % 100;
+ break;
+ case SDRAM:
+ leftOfPoint = (data[i] & 0xf0) >> 4;
+ if (leftOfPoint > 7) {
+ leftOfPoint = data[i] & 0x70 >> 4;
+ sign = -1;
+ }
+ rightOfPoint = (data[i] & 0x0f);
+ break;
+ }
+ dimmInfo->dataInputSetupTime =
+ (leftOfPoint * 100 + rightOfPoint) * sign;
+ DP (printf
+ ("Data Input Setup Time [ns]: %d.%d\n",
+ sign * leftOfPoint, rightOfPoint));
+ break;
+/*------------------------------------------------------------------------------------------------------------------------------*/
+
+ case 35: /* Data Input Hold Time */
+ sign = 1;
+ switch (dimmInfo->memoryType) {
+ case DDR:
+ time_tmp =
+ (((data[i] & 0xf0) >> 4) * 10) +
+ ((data[i] & 0x0f));
+ leftOfPoint = time_tmp / 100;
+ rightOfPoint = time_tmp % 100;
+ break;
+ case SDRAM:
+ leftOfPoint = (data[i] & 0xf0) >> 4;
+ if (leftOfPoint > 7) {
+ leftOfPoint = data[i] & 0x70 >> 4;
+ sign = -1;
+ }
+ rightOfPoint = (data[i] & 0x0f);
+ break;
+ }
+ dimmInfo->dataInputHoldTime =
+ (leftOfPoint * 100 + rightOfPoint) * sign;
+ DP (printf
+ ("Data Input Hold Time [ns]: %d.%d\n\n",
+ sign * leftOfPoint, rightOfPoint));
+ break;
+/*------------------------------------------------------------------------------------------------------------------------------*/
+ }
+ }
+ /* calculating the sdram density */
+ for (i = 0;
+ i < dimmInfo->numOfRowAddresses + dimmInfo->numOfColAddresses;
+ i++) {
+ density = density * 2;
+ }
+ dimmInfo->deviceDensity = density * dimmInfo->numOfBanksOnEachDevice *
+ dimmInfo->sdramWidth;
+ dimmInfo->numberOfDevices =
+ (dimmInfo->dataWidth / dimmInfo->sdramWidth) *
+ dimmInfo->numOfModuleBanks;
+ devicesForErrCheck =
+ (dimmInfo->dataWidth - 64) / dimmInfo->sdramWidth;
+ if ((dimmInfo->errorCheckType == 0x1)
+ || (dimmInfo->errorCheckType == 0x2)
+ || (dimmInfo->errorCheckType == 0x3)) {
+ dimmInfo->size =
+ (dimmInfo->deviceDensity / 8) *
+ (dimmInfo->numberOfDevices -
+ /* ronen on the 1G dimm we get wrong value. (was devicesForErrCheck) */
+ dimmInfo->numberOfDevices / 8);
+ } else {
+ dimmInfo->size =
+ (dimmInfo->deviceDensity / 8) *
+ dimmInfo->numberOfDevices;
+ }
+
+ /* compute the module DRB size */
+ tmp = (1 <<
+ (dimmInfo->numOfRowAddresses + dimmInfo->numOfColAddresses));
+ tmp *= dimmInfo->numOfModuleBanks;
+ tmp *= dimmInfo->sdramWidth;
+ tmp = tmp >> 24; /* div by 0x4000000 (64M) */
+ dimmInfo->drb_size = (uchar) tmp;
+ DP (printf ("Module DRB size (n*64Mbit): %d\n", dimmInfo->drb_size));
+
+ /* try a CAS latency of 3 first... */
+
+ /* bit 1 is CL2, bit 2 is CL3 */
+ supp_cal = (dimmInfo->suportedCasLatencies & 0x6) >> 1;
+
+ cal_val = 0;
+ if (supp_cal & 3) {
+ if (NS10to10PS (data[9]) <= tmemclk)
+ cal_val = 3;
+ }
+
+ /* then 2... */
+ if (supp_cal & 2) {
+ if (NS10to10PS (data[23]) <= tmemclk)
+ cal_val = 2;
+ }
+
+ DP (printf ("cal_val = %d\n", cal_val));
+
+ /* bummer, did't work... */
+ if (cal_val == 0) {
+ DP (printf ("Couldn't find a good CAS latency\n"));
+ hang ();
+ return 0;
+ }
+
+ return true;
+#endif
+}
+
+/* sets up the GT properly with information passed in */
+int setup_sdram (AUX_MEM_DIMM_INFO * info)
+{
+ ulong tmp, check;
+ ulong tmp_sdram_mode = 0; /* 0x141c */
+ ulong tmp_dunit_control_low = 0; /* 0x1404 */
+ int i;
+
+ /* added 8/21/2003 P. Marchese */
+ unsigned int sdram_config_reg;
+
+ /* added 10/10/2003 P. Marchese */
+ ulong sdram_chip_size;
+
+ /* sanity checking */
+ if (!info->numOfModuleBanks) {
+ printf ("setup_sdram called with 0 banks\n");
+ return 1;
+ }
+
+ /* delay line */
+ set_dfcdlInit (); /* may be its not needed */
+ DP (printf ("Delay line set done\n"));
+
+ /* set SDRAM mode NOP */ /* To_do check it */
+ GT_REG_WRITE (SDRAM_OPERATION, 0x5);
+ while (GTREGREAD (SDRAM_OPERATION) != 0) {
+ DP (printf
+ ("\n*** SDRAM_OPERATION 1418: Module still busy ... please wait... ***\n"));
+ }
+
+ /* SDRAM configuration */
+/* added 8/21/2003 P. Marchese */
+/* code allows usage of registered DIMMS */
+
+ /* figure out the memory refresh internal */
+ switch (info->RefreshInterval) {
+ case 0x0:
+ case 0x80: /* refresh period is 15.625 usec */
+ sdram_config_reg =
+ (unsigned int) (((float) 15.625 * (float) CFG_BUS_HZ)
+ / (float) 1000000.0);
+ break;
+ case 0x1:
+ case 0x81: /* refresh period is 3.9 usec */
+ sdram_config_reg =
+ (unsigned int) (((float) 3.9 * (float) CFG_BUS_HZ) /
+ (float) 1000000.0);
+ break;
+ case 0x2:
+ case 0x82: /* refresh period is 7.8 usec */
+ sdram_config_reg =
+ (unsigned int) (((float) 7.8 * (float) CFG_BUS_HZ) /
+ (float) 1000000.0);
+ break;
+ case 0x3:
+ case 0x83: /* refresh period is 31.3 usec */
+ sdram_config_reg =
+ (unsigned int) (((float) 31.3 * (float) CFG_BUS_HZ) /
+ (float) 1000000.0);
+ break;
+ case 0x4:
+ case 0x84: /* refresh period is 62.5 usec */
+ sdram_config_reg =
+ (unsigned int) (((float) 62.5 * (float) CFG_BUS_HZ) /
+ (float) 1000000.0);
+ break;
+ case 0x5:
+ case 0x85: /* refresh period is 125 usec */
+ sdram_config_reg =
+ (unsigned int) (((float) 125 * (float) CFG_BUS_HZ) /
+ (float) 1000000.0);
+ break;
+ default: /* refresh period undefined */
+ printf ("DRAM refresh period is unknown!\n");
+ printf ("Aborting DRAM setup with an error\n");
+ hang ();
+ break;
+ }
+ DP (printf ("calculated refresh interval %0x\n", sdram_config_reg));
+
+ /* make sure the refresh value is only 14 bits */
+ if (sdram_config_reg > 0x1fff)
+ sdram_config_reg = 0x1fff;
+ DP (printf ("adjusted refresh interval %0x\n", sdram_config_reg));
+
+ /* we want physical bank interleaving and */
+ /* virtual bank interleaving enabled so do nothing */
+ /* since these bits need to be zero to enable the interleaving */
+
+ /* registered DRAM ? */
+ if (info->registeredAddrAndControlInputs == 1) {
+ /* it's registered DRAM, so set the reg. DRAM bit */
+ sdram_config_reg = sdram_config_reg | BIT17;
+ DP (printf ("Enabling registered DRAM bit\n"));
+ }
+ /* turn on DRAM ECC? */
+#ifdef CONFIG_MV64460_ECC
+ if (info->errorCheckType == 0x2) {
+ /* DRAM has ECC, so turn it on */
+ sdram_config_reg = sdram_config_reg | BIT18;
+ DP (printf ("Enabling ECC\n"));
+ }
+#endif
+ /* set the data DQS pin configuration */
+ switch (info->sdramWidth) {
+ case 0x4: /* memory is x4 */
+ sdram_config_reg = sdram_config_reg | BIT20 | BIT21;
+ DP (printf ("Data DQS pins set for 16 pins\n"));
+ break;
+ case 0x8: /* memory is x8 or x16 */
+ case 0x10:
+ sdram_config_reg = sdram_config_reg | BIT21;
+ DP (printf ("Data DQS pins set for 8 pins\n"));
+ break;
+ case 0x20: /* memory is x32 */
+ /* both bits are cleared for x32 so nothing to do */
+ DP (printf ("Data DQS pins set for 2 pins\n"));
+ break;
+ default: /* memory width unsupported */
+ printf ("DRAM chip width is unknown!\n");
+ printf ("Aborting DRAM setup with an error\n");
+ hang ();
+ break;
+ }
+
+ /*ronen db64460 */
+ /* perform read buffer assignments */
+ /* we are going to use the Power-up defaults */
+ /* bit 27 = PCI bus #0 = buffer 0 */
+ /* bit 28 = PCI bus #1 = buffer 0 */
+ /* bit 29 = MPSC = buffer 0 */
+ /* bit 30 = IDMA = buffer 0 */
+ /* bit 31 = Gigabit = buffer 0 */
+ sdram_config_reg = sdram_config_reg | 0x58000000;
+ sdram_config_reg = sdram_config_reg & 0xffffff00;
+ /* bit 14 FBSplit = FCRAM controller bsplit enable. */
+ /* bit 15 vw = FCRAM Variable write length enable. */
+ /* bit 16 DType = Dram Type (0 = FCRAM,1 = Standard) */
+ sdram_config_reg = sdram_config_reg | BIT14 | BIT15;
+
+ /* write the value into the SDRAM configuration register */
+ GT_REG_WRITE (SDRAM_CONFIG, sdram_config_reg);
+ DP (printf ("sdram_conf 0x1400: %08x\n", GTREGREAD (SDRAM_CONFIG)));
+
+ /* SDRAM open pages control keep open as much as I can */
+ GT_REG_WRITE (SDRAM_OPEN_PAGES_CONTROL, 0x0);
+ DP (printf
+ ("sdram_open_pages_controll 0x1414: %08x\n",
+ GTREGREAD (SDRAM_OPEN_PAGES_CONTROL)));
+
+ /* SDRAM D_UNIT_CONTROL_LOW 0x1404 */
+ tmp = (GTREGREAD (D_UNIT_CONTROL_LOW) & 0x01); /* Clock Domain Sync from power on reset */
+ if (tmp == 0)
+ DP (printf ("Core Signals are sync (by HW-Setting)!!!\n"));
+ else
+ DP (printf
+ ("Core Signals syncs. are bypassed (by HW-Setting)!!!\n"));
+
+ /* SDRAM set CAS Latency according to SPD information */
+ switch (info->memoryType) {
+ case SDRAM:
+ printf ("### SD-RAM not supported !!!\n");
+ printf ("Aborting!!!\n");
+ hang ();
+ /* ToDo fill SD-RAM if needed !!!!! */
+ break;
+ /* Calculate the settings for SDRAM mode and Dunit control low registers */
+ /* Values set according to technical bulletin TB-92 rev. c */
+ case DDR:
+ DP (printf ("### SET-CL for DDR-RAM\n"));
+ /* ronen db64460 - change the tmp_dunit_control_low setting!!! */
+ switch (info->maxClSupported_DDR) {
+ case DDR_CL_3:
+ tmp_sdram_mode = 0x32; /* CL=3 Burstlength = 4 */
+ if (tmp == 1) { /* clocks sync */
+ if (info->registeredAddrAndControlInputs == 1) /* registerd DDR SDRAM? */
+ tmp_dunit_control_low = 0x05110051;
+ else
+ tmp_dunit_control_low = 0x24110051;
+ DP (printf
+ ("Max. CL is 3 CLKs 0x141c= %08lx, 0x1404 = %08lx\n",
+ tmp_sdram_mode, tmp_dunit_control_low));
+ printf ("Warnning: DRAM ClkSync was never tested(db64460)!!!!!\n");
+ } else { /* clk sync. bypassed */
+
+ if (info->registeredAddrAndControlInputs == 1) /* registerd DDR SDRAM? */
+ tmp_dunit_control_low = 0xC5000540;
+ else
+ tmp_dunit_control_low = 0xC4000540;
+ DP (printf
+ ("Max. CL is 3 CLKs 0x141c= %08lx, 0x1404 = %08lx\n",
+ tmp_sdram_mode, tmp_dunit_control_low));
+ }
+ break;
+ case DDR_CL_2_5:
+ tmp_sdram_mode = 0x62; /* CL=2.5 Burstlength = 4 */
+ if (tmp == 1) { /* clocks sync */
+ if (info->registeredAddrAndControlInputs == 1) /* registerd DDR SDRAM? */
+ tmp_dunit_control_low = 0x25110051;
+ else
+ tmp_dunit_control_low = 0x24110051;
+ DP (printf
+ ("Max. CL is 2.5 CLKs 0x141c= %08lx, 0x1404 = %08lx\n",
+ tmp_sdram_mode, tmp_dunit_control_low));
+ printf ("Warnning: DRAM ClkSync was never tested(db64460)!!!!!\n");
+ } else { /* clk sync. bypassed */
+
+ if (info->registeredAddrAndControlInputs == 1) { /* registerd DDR SDRAM? */
+ tmp_dunit_control_low = 0xC5000540;
+ /* printf("CL = 2.5, Clock Unsync'ed, Dunit Control Low register setting undefined\n");1 */
+ /* printf("Aborting!!!\n");1 */
+ /* hang();1 */
+ } else
+ tmp_dunit_control_low = 0xC4000540;
+ DP (printf
+ ("Max. CL is 2.5 CLKs 0x141c= %08lx, 0x1404 = %08lx\n",
+ tmp_sdram_mode, tmp_dunit_control_low));
+ }
+ break;
+ case DDR_CL_2:
+ tmp_sdram_mode = 0x22; /* CL=2 Burstlength = 4 */
+ if (tmp == 1) { /* clocks sync */
+ if (info->registeredAddrAndControlInputs == 1) /* registerd DDR SDRAM? */
+ tmp_dunit_control_low = 0x04110051;
+ else
+ tmp_dunit_control_low = 0x03110051;
+ DP (printf
+ ("Max. CL is 2 CLKs 0x141c= %08lx, 0x1404 = %08lx\n",
+ tmp_sdram_mode, tmp_dunit_control_low));
+ printf ("Warnning: DRAM ClkSync was never tested(db64460)!!!!!\n");
+ } else { /* clk sync. bypassed */
+
+ if (info->registeredAddrAndControlInputs == 1) { /* registerd DDR SDRAM? */
+ /*printf("CL = 2, Clock Unsync'ed, Dunit Control Low register setting undefined\n");1 */
+ /*printf("Aborting!!!\n");1 */
+ /*hang();1 */
+ tmp_dunit_control_low = 0xC4000540;
+ } else
+ tmp_dunit_control_low = 0xC3000540;;
+ DP (printf
+ ("Max. CL is 2 CLKs 0x141c= %08lx, 0x1404 = %08lx\n",
+ tmp_sdram_mode, tmp_dunit_control_low));
+ }
+ break;
+ case DDR_CL_1_5:
+ tmp_sdram_mode = 0x52; /* CL=1.5 Burstlength = 4 */
+ if (tmp == 1) { /* clocks sync */
+ if (info->registeredAddrAndControlInputs == 1) /* registerd DDR SDRAM? */
+ tmp_dunit_control_low = 0x24110051;
+ else
+ tmp_dunit_control_low = 0x23110051;
+ DP (printf
+ ("Max. CL is 1.5 CLKs 0x141c= %08lx, 0x1404 = %08lx\n",
+ tmp_sdram_mode, tmp_dunit_control_low));
+ printf ("Warnning: DRAM ClkSync was never tested(db64460)!!!!!\n");
+ } else { /* clk sync. bypassed */
+
+ if (info->registeredAddrAndControlInputs == 1) { /* registerd DDR SDRAM? */
+ /*printf("CL = 1.5, Clock Unsync'ed, Dunit Control Low register setting undefined\n");1 */
+ /*printf("Aborting!!!\n");1 */
+ /*hang();1 */
+ tmp_dunit_control_low = 0xC4000540;
+ } else
+ tmp_dunit_control_low = 0xC3000540;
+ DP (printf
+ ("Max. CL is 1.5 CLKs 0x141c= %08lx, 0x1404 = %08lx\n",
+ tmp_sdram_mode, tmp_dunit_control_low));
+ }
+ break;
+
+ default:
+ printf ("Max. CL is out of range %d\n",
+ info->maxClSupported_DDR);
+ hang ();
+ break;
+ } /* end DDR switch */
+ break;
+ } /* end CL switch */
+
+ /* Write results of CL detection procedure */
+ /* set SDRAM mode reg. 0x141c */
+ GT_REG_WRITE (SDRAM_MODE, tmp_sdram_mode);
+
+ /* set SDRAM mode SetCommand 0x1418 */
+ GT_REG_WRITE (SDRAM_OPERATION, 0x3);
+ while (GTREGREAD (SDRAM_OPERATION) != 0) {
+ DP (printf
+ ("\n*** SDRAM_OPERATION 0x1418 after SDRAM_MODE: Module still busy ... please wait... ***\n"));
+ }
+
+ /* SDRAM D_UNIT_CONTROL_LOW 0x1404 */
+ GT_REG_WRITE (D_UNIT_CONTROL_LOW, tmp_dunit_control_low);
+
+ /* set SDRAM mode SetCommand 0x1418 */
+ GT_REG_WRITE (SDRAM_OPERATION, 0x3);
+ while (GTREGREAD (SDRAM_OPERATION) != 0) {
+ DP (printf
+ ("\n*** SDRAM_OPERATION 1418 after D_UNIT_CONTROL_LOW: Module still busy ... please wait... ***\n"));
+ }
+
+/*------------------------------------------------------------------------------ */
+
+ /* bank parameters */
+ /* SDRAM address decode register 0x1410 */
+ /* program this with the default value */
+ tmp = 0x02; /* power-up default address select decoding value */
+
+ DP (printf ("drb_size (n*64Mbit): %d\n", info->drb_size));
+/* figure out the DRAM chip size */
+ sdram_chip_size =
+ (1 << (info->numOfRowAddresses + info->numOfColAddresses));
+ sdram_chip_size *= info->sdramWidth;
+ sdram_chip_size *= 4;
+ DP (printf ("computed sdram chip size is %#lx\n", sdram_chip_size));
+ /* divide sdram chip size by 64 Mbits */
+ sdram_chip_size = sdram_chip_size / 0x4000000;
+ switch (sdram_chip_size) {
+ case 1: /* 64 Mbit */
+ case 2: /* 128 Mbit */
+ DP (printf ("RAM-Device_size 64Mbit or 128Mbit)\n"));
+ tmp |= (0x00 << 4);
+ break;
+ case 4: /* 256 Mbit */
+ case 8: /* 512 Mbit */
+ DP (printf ("RAM-Device_size 256Mbit or 512Mbit)\n"));
+ tmp |= (0x01 << 4);
+ break;
+ case 16: /* 1 Gbit */
+ case 32: /* 2 Gbit */
+ DP (printf ("RAM-Device_size 1Gbit or 2Gbit)\n"));
+ tmp |= (0x02 << 4);
+ break;
+ default:
+ printf ("Error in dram size calculation\n");
+ printf ("RAM-Device_size is unsupported\n");
+ hang ();
+ }
+
+ /* SDRAM address control */
+ GT_REG_WRITE (SDRAM_ADDR_CONTROL, tmp);
+ DP (printf
+ ("setting up sdram address control (0x1410) with: %08lx \n",
+ tmp));
+
+/* ------------------------------------------------------------------------------ */
+/* same settings for registerd & non-registerd DDR SDRAM */
+ DP (printf
+ ("setting up sdram_timing_control_low (0x1408) with: %08x \n",
+ 0x01501220));
+ /*ronen db64460 */
+ GT_REG_WRITE (SDRAM_TIMING_CONTROL_LOW, 0x01501220);
+
+
+/* ------------------------------------------------------------------------------ */
+
+ /* SDRAM configuration */
+ tmp = GTREGREAD (SDRAM_CONFIG);
+
+ if (info->registeredAddrAndControlInputs
+ || info->registeredDQMBinputs) {
+ tmp |= (1 << 17);
+ DP (printf
+ ("SPD says: registered Addr. and Cont.: %d; registered DQMBinputs: %d\n",
+ info->registeredAddrAndControlInputs,
+ info->registeredDQMBinputs));
+ }
+
+ /* Use buffer 1 to return read data to the CPU
+ * Page 426 MV6indent: Standard input:1464: Warning:old style assignment ambiguity in "=*". Assuming "= *"
+
+indent: Standard input:1465: Warning:old style assignment ambiguity in "=*". Assuming "= *"
+
+4460 */
+ tmp |= (1 << 26);
+ DP (printf
+ ("Before Buffer assignment - sdram_conf (0x1400): %08x\n",
+ GTREGREAD (SDRAM_CONFIG)));
+ DP (printf
+ ("After Buffer assignment - sdram_conf (0x1400): %08x\n",
+ GTREGREAD (SDRAM_CONFIG)));
+
+ /* SDRAM timing To_do: */
+/* ------------------------------------------------------------------------------ */
+ /* ronen db64460 */
+ DP (printf
+ ("setting up sdram_timing_control_high (0x140c) with: %08x \n",
+ 0xc));
+ GT_REG_WRITE (SDRAM_TIMING_CONTROL_HIGH, 0xc);
+
+ DP (printf
+ ("setting up sdram address pads control (0x14c0) with: %08x \n",
+ 0x7d5014a));
+ GT_REG_WRITE (SDRAM_ADDR_CTRL_PADS_CALIBRATION, 0x7d5014a);
+
+ DP (printf
+ ("setting up sdram data pads control (0x14c4) with: %08x \n",
+ 0x7d5014a));
+ GT_REG_WRITE (SDRAM_DATA_PADS_CALIBRATION, 0x7d5014a);
+
+/* ------------------------------------------------------------------------------ */
+
+ /* set the SDRAM configuration for each bank */
+
+/* for (i = info->slot * 2; i < ((info->slot * 2) + info->banks); i++) */
+ {
+ i = info->slot;
+ DP (printf
+ ("\n*** Running a MRS cycle for bank %d ***\n", i));
+
+ /* map the bank */
+ memory_map_bank (i, 0, GB / 4);
+
+ /* set SDRAM mode */ /* To_do check it */
+ GT_REG_WRITE (SDRAM_OPERATION, 0x3);
+ check = GTREGREAD (SDRAM_OPERATION);
+ DP (printf
+ ("\n*** SDRAM_OPERATION 1418 (0 = Normal Operation) = %08lx ***\n",
+ check));
+
+
+ /* switch back to normal operation mode */
+ GT_REG_WRITE (SDRAM_OPERATION, 0);
+ check = GTREGREAD (SDRAM_OPERATION);
+ DP (printf
+ ("\n*** SDRAM_OPERATION 1418 (0 = Normal Operation) = %08lx ***\n",
+ check));
+
+ /* unmap the bank */
+ memory_map_bank (i, 0, 0);
+ }
+
+ return 0;
+
+}
+
+/*
+ * Check memory range for valid RAM. A simple memory test determines
+ * the actually available RAM size between addresses `base' and
+ * `base + maxsize'. Some (not all) hardware errors are detected:
+ * - short between address lines
+ * - short between data lines
+ */
+long int dram_size (long int *base, long int maxsize)
+{
+ volatile long int *addr, *b = base;
+ long int cnt, val, save1, save2;
+
+#define STARTVAL (1<<20) /* start test at 1M */
+ for (cnt = STARTVAL / sizeof (long); cnt < maxsize / sizeof (long);
+ cnt <<= 1) {
+ addr = base + cnt; /* pointer arith! */
+
+ save1 = *addr; /* save contents of addr */
+ save2 = *b; /* save contents of base */
+
+ *addr = cnt; /* write cnt to addr */
+ *b = 0; /* put null at base */
+
+ /* check at base address */
+ if ((*b) != 0) {
+ *addr = save1; /* restore *addr */
+ *b = save2; /* restore *b */
+ return (0);
+ }
+ val = *addr; /* read *addr */
+ val = *addr; /* read *addr */
+
+ *addr = save1;
+ *b = save2;
+
+ if (val != cnt) {
+ DP (printf
+ ("Found %08x at Address %08x (failure)\n",
+ (unsigned int) val, (unsigned int) addr));
+ /* fix boundary condition.. STARTVAL means zero */
+ if (cnt == STARTVAL / sizeof (long))
+ cnt = 0;
+ return (cnt * sizeof (long));
+ }
+ }
+ return maxsize;
+}
+
+/* ------------------------------------------------------------------------- */
+
+/* ppcboot interface function to SDRAM init - this is where all the
+ * controlling logic happens */
+long int initdram (int board_type)
+{
+ int s0 = 0, s1 = 0;
+ int checkbank[4] = {[0 ... 3] = 0 };
+ ulong realsize, total, check;
+ AUX_MEM_DIMM_INFO dimmInfo1;
+ AUX_MEM_DIMM_INFO dimmInfo2;
+ int nhr, bank_no;
+ ulong dest, memSpaceAttr;
+
+ /* first, use the SPD to get info about the SDRAM/ DDRRAM */
+
+ /* check the NHR bit and skip mem init if it's already done */
+ nhr = get_hid0 () & (1 << 16);
+
+ if (nhr) {
+ printf ("Skipping SD- DDRRAM setup due to NHR bit being set\n");
+ } else {
+ /* DIMM0 */
+ s0 = check_dimm (0, &dimmInfo1);
+
+ /* DIMM1 */
+ s1 = check_dimm (1, &dimmInfo2);
+
+ memory_map_bank (0, 0, 0);
+ memory_map_bank (1, 0, 0);
+ memory_map_bank (2, 0, 0);
+ memory_map_bank (3, 0, 0);
+
+ /* ronen check correct set of DIMMS */
+ if (dimmInfo1.numOfModuleBanks && dimmInfo2.numOfModuleBanks) {
+ if (dimmInfo1.errorCheckType !=
+ dimmInfo2.errorCheckType)
+ printf ("***WARNNING***!!!! different ECC support of the DIMMS\n");
+ if (dimmInfo1.maxClSupported_DDR !=
+ dimmInfo2.maxClSupported_DDR)
+ printf ("***WARNNING***!!!! different CAL setting of the DIMMS\n");
+ if (dimmInfo1.registeredAddrAndControlInputs !=
+ dimmInfo2.registeredAddrAndControlInputs)
+ printf ("***WARNNING***!!!! different Registration setting of the DIMMS\n");
+ }
+
+ if (dimmInfo1.numOfModuleBanks && setup_sdram (&dimmInfo1)) {
+ printf ("Setup for DIMM1 failed.\n");
+ }
+
+ if (dimmInfo2.numOfModuleBanks && setup_sdram (&dimmInfo2)) {
+ printf ("Setup for DIMM2 failed.\n");
+ }
+
+ /* set the NHR bit */
+ set_hid0 (get_hid0 () | (1 << 16));
+ }
+ /* next, size the SDRAM banks */
+
+ realsize = total = 0;
+ check = GB / 4;
+ if (dimmInfo1.numOfModuleBanks > 0) {
+ checkbank[0] = 1;
+ }
+ if (dimmInfo1.numOfModuleBanks > 1) {
+ checkbank[1] = 1;
+ }
+ if (dimmInfo1.numOfModuleBanks > 2)
+ printf ("Error, SPD claims DIMM1 has >2 banks\n");
+
+ printf ("-- DIMM1 has %d banks\n", dimmInfo1.numOfModuleBanks);
+
+ if (dimmInfo2.numOfModuleBanks > 0) {
+ checkbank[2] = 1;
+ }
+ if (dimmInfo2.numOfModuleBanks > 1) {
+ checkbank[3] = 1;
+ }
+ if (dimmInfo2.numOfModuleBanks > 2)
+ printf ("Error, SPD claims DIMM2 has >2 banks\n");
+
+ printf ("-- DIMM2 has %d banks\n", dimmInfo2.numOfModuleBanks);
+
+ for (bank_no = 0; bank_no < CFG_DRAM_BANKS; bank_no++) {
+ /* skip over banks that are not populated */
+ if (!checkbank[bank_no])
+ continue;
+
+ /* ronen - realsize = dram_size((long int *)total, check); */
+ if (bank_no == 0 || bank_no == 1) {
+ if (checkbank[1] == 1)
+ realsize = dimmInfo1.size / 2;
+ else
+ realsize = dimmInfo1.size;
+ }
+ if (bank_no == 2 || bank_no == 3) {
+ if (checkbank[3] == 1)
+ realsize = dimmInfo2.size / 2;
+ else
+ realsize = dimmInfo2.size;
+ }
+ memory_map_bank (bank_no, total, realsize);
+
+ /* ronen - initialize the DRAM for ECC */
+#ifdef CONFIG_MV64460_ECC
+ if ((dimmInfo1.errorCheckType != 0) &&
+ ((dimmInfo2.errorCheckType != 0)
+ || (dimmInfo2.numOfModuleBanks == 0))) {
+ printf ("ECC Initialization of Bank %d:", bank_no);
+ memSpaceAttr = ((~(BIT0 << bank_no)) & 0xf) << 8;
+ mvDmaSetMemorySpace (0, 0, memSpaceAttr, total,
+ realsize);
+ for (dest = total; dest < total + realsize;
+ dest += _8M) {
+ mvDmaTransfer (0, total, dest, _8M,
+ BIT8 /*DMA_DTL_128BYTES */ |
+ BIT3 /*DMA_HOLD_SOURCE_ADDR */
+ |
+ BIT11
+ /*DMA_BLOCK_TRANSFER_MODE */ );
+ while (mvDmaIsChannelActive (0));
+ }
+ printf (" PASS\n");
+ }
+#endif
+
+ total += realsize;
+ }
+
+ /* ronen */
+ switch ((GTREGREAD (0x141c) >> 4) & 0x7) {
+ case 0x2:
+ printf ("CAS Latency = 2");
+ break;
+ case 0x3:
+ printf ("CAS Latency = 3");
+ break;
+ case 0x5:
+ printf ("CAS Latency = 1.5");
+ break;
+ case 0x6:
+ printf ("CAS Latency = 2.5");
+ break;
+ }
+ printf (" tRP = %d tRAS = %d tRCD=%d\n",
+ ((GTREGREAD (0x1408) >> 8) & 0xf) + 1,
+ ((GTREGREAD (0x1408) >> 20) & 0xf) + 1,
+ ((GTREGREAD (0x1408) >> 4) & 0xf) + 1);
+
+/* Setup Ethernet DMA Adress window to DRAM Area */
+ if (total > _256M)
+ printf ("*** ONLY the first 256MB DRAM memory are used out of the ");
+ else
+ printf ("Total SDRAM memory is ");
+ /* (cause all the 4 BATS are taken) */
+ return (total);
+}
+
+
+/* ronen- add Idma functions for usage of the ecc dram init. */
+/*******************************************************************************
+* mvDmaIsChannelActive - Checks if a engine is busy.
+********************************************************************************/
+int mvDmaIsChannelActive (int engine)
+{
+ ulong data;
+
+ data = GTREGREAD (MV64460_DMA_CHANNEL0_CONTROL + 4 * engine);
+ if (data & BIT14 /*activity status */ ) {
+ return 1;
+ }
+ return 0;
+}
+
+/*******************************************************************************
+* mvDmaSetMemorySpace - Set a DMA memory window for the DMA's address decoding
+* map.
+*******************************************************************************/
+int mvDmaSetMemorySpace (ulong memSpace,
+ ulong memSpaceTarget,
+ ulong memSpaceAttr, ulong baseAddress, ulong size)
+{
+ ulong temp;
+
+ /* The base address must be aligned to the size. */
+ if (baseAddress % size != 0) {
+ return 0;
+ }
+ if (size >= 0x10000 /*64K */ ) {
+ size &= 0xffff0000;
+ baseAddress = (baseAddress & 0xffff0000);
+ /* Set the new attributes */
+ GT_REG_WRITE (MV64460_DMA_BASE_ADDR_REG0 + memSpace * 8,
+ (baseAddress | memSpaceTarget | memSpaceAttr));
+ GT_REG_WRITE ((MV64460_DMA_SIZE_REG0 + memSpace * 8),
+ (size - 1) & 0xffff0000);
+ temp = GTREGREAD (MV64460_DMA_BASE_ADDR_ENABLE_REG);
+ GT_REG_WRITE (DMA_BASE_ADDR_ENABLE_REG,
+ (temp & ~(BIT0 << memSpace)));
+ return 1;
+ }
+ return 0;
+}
+
+
+/*******************************************************************************
+* mvDmaTransfer - Transfer data from sourceAddr to destAddr on one of the 4
+* DMA channels.
+********************************************************************************/
+int mvDmaTransfer (int engine, ulong sourceAddr,
+ ulong destAddr, ulong numOfBytes, ulong command)
+{
+ ulong engOffReg = 0; /* Engine Offset Register */
+
+ if (numOfBytes > 0xffff) {
+ command = command | BIT31 /*DMA_16M_DESCRIPTOR_MODE */ ;
+ }
+ command = command | ((command >> 6) & 0x7);
+ engOffReg = engine * 4;
+ GT_REG_WRITE (MV64460_DMA_CHANNEL0_BYTE_COUNT + engOffReg,
+ numOfBytes);
+ GT_REG_WRITE (MV64460_DMA_CHANNEL0_SOURCE_ADDR + engOffReg,
+ sourceAddr);
+ GT_REG_WRITE (MV64460_DMA_CHANNEL0_DESTINATION_ADDR + engOffReg,
+ destAddr);
+ command =
+ command | BIT12 /*DMA_CHANNEL_ENABLE */ | BIT9
+ /*DMA_NON_CHAIN_MODE */ ;
+ /* Activate DMA engine By writting to mvDmaControlRegister */
+ GT_REG_WRITE (MV64460_DMA_CHANNEL0_CONTROL + engOffReg, command);
+ return 1;
+}
+
+/****************************************************************************************
+ * SDRAM INIT *
+ * This procedure detect all Sdram types: 64, 128, 256, 512 Mbit, 1Gbit and 2Gb *
+ * This procedure fits only the Atlantis *
+ * *
+ ***************************************************************************************/
+
+
+/****************************************************************************************
+ * DFCDL initialize MV643xx Design Considerations *
+ * *
+ ***************************************************************************************/
+int set_dfcdlInit (void)
+{
+ /*ronen the dfcdl init are done by the I2C */
+ return (0);
+}