OMAP3: am3517_evm: Add NAND MTD partitions with UBI/UBIFS support
- Add required UBI/UBIFS config definitions
- Add reasonable MTD partition layout
- Remove JFFS2 config definitions
- Drop some CFI verbage and definitions
- Make comment 'one-liners' truly one line
- Improve readability and content arrangement
Signed-off-by: Derald D. Woods <woods.technical@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
diff --git a/include/configs/am3517_evm.h b/include/configs/am3517_evm.h
index 98a59c5..5b689a8 100644
--- a/include/configs/am3517_evm.h
+++ b/include/configs/am3517_evm.h
@@ -13,14 +13,17 @@
#ifndef __CONFIG_H
#define __CONFIG_H
+/* High Level Configuration Options */
+
+#define CONFIG_OMAP
+#define CONFIG_OMAP_COMMON
+
#define CONFIG_SYS_CACHELINE_SIZE 64
-/*
- * High Level Configuration Options
- */
-#define CONFIG_OMAP 1 /* in a TI OMAP core */
-#define CONFIG_OMAP3_AM3517EVM 1 /* working with AM3517EVM */
-#define CONFIG_OMAP_COMMON
+#define CONFIG_SYS_NO_FLASH
+
+#define CONFIG_NR_DRAM_BANKS 2 /* CS1 may or may not be populated */
+
/* Common ARM Erratas */
#define CONFIG_ARM_ERRATA_454179
#define CONFIG_ARM_ERRATA_430973
@@ -28,59 +31,48 @@
#define CONFIG_EMIF4 /* The chip has EMIF4 controller */
+/*
+ * 1MB into the SDRAM to allow for SPL's bss at the beginning of SDRAM
+ * 64 bytes before this address should be set aside for u-boot.img's
+ * header. That is 0x800FFFC0--0x80100000 should not be used for any
+ * other needs.
+ */
+#define CONFIG_SYS_TEXT_BASE 0x80100000
+#define CONFIG_SYS_SPL_MALLOC_START 0x80208000
+#define CONFIG_SYS_SPL_MALLOC_SIZE 0x100000
+
#include <asm/arch/cpu.h> /* get chip and board defs */
#include <asm/arch/omap.h>
-/*
- * Display CPU and Board information
- */
-#define CONFIG_DISPLAY_CPUINFO 1
-#define CONFIG_DISPLAY_BOARDINFO 1
+/* Display CPU and Board information */
+#define CONFIG_DISPLAY_CPUINFO
+#define CONFIG_DISPLAY_BOARDINFO
+#define CONFIG_OF_LIBFDT
+#define CONFIG_MISC_INIT_R
+#define CONFIG_CMDLINE_TAG /* enable passing of ATAGs */
+#define CONFIG_SETUP_MEMORY_TAGS
+#define CONFIG_INITRD_TAG
+#define CONFIG_REVISION_TAG
/* Clock Defines */
#define V_OSCK 26000000 /* Clock output from T2 */
#define V_SCLK (V_OSCK >> 1)
-#define CONFIG_MISC_INIT_R
+/* Size of malloc() pool */
+#define CONFIG_SYS_MALLOC_LEN (16 << 20)
-#define CONFIG_OF_LIBFDT
+/* Hardware drivers */
-#define CONFIG_CMDLINE_TAG 1 /* enable passing of ATAGs */
-#define CONFIG_SETUP_MEMORY_TAGS 1
-#define CONFIG_INITRD_TAG 1
-#define CONFIG_REVISION_TAG 1
-
-/*
- * Size of malloc() pool
- */
-#define CONFIG_ENV_SIZE (128 << 10) /* 128 KiB sector */
-#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + (128 << 10))
-/*
- * DDR related
- */
-#define CONFIG_SYS_CS0_SIZE (256 * 1024 * 1024)
-
-/*
- * Hardware drivers
- */
-
-/*
- * OMAP GPIO configuration
- */
+/* OMAP GPIO configuration */
#define CONFIG_OMAP_GPIO
-/*
- * NS16550 Configuration
- */
+/* NS16550 Configuration */
#define V_NS16550_CLK 48000000 /* 48MHz (APLL96/2) */
-
#define CONFIG_SYS_NS16550_SERIAL
#define CONFIG_SYS_NS16550_REG_SIZE (-4)
#define CONFIG_SYS_NS16550_CLK V_NS16550_CLK
-/*
- * select serial console configuration
- */
+/* select serial console configuration */
#define CONFIG_CONS_INDEX 3
#define CONFIG_SYS_NS16550_COM3 OMAP34XX_UART3
#define CONFIG_SERIAL3 3 /* UART3 on AM3517 EVM */
@@ -90,10 +82,12 @@
#define CONFIG_BAUDRATE 115200
#define CONFIG_SYS_BAUDRATE_TABLE {4800, 9600, 19200, 38400, 57600,\
115200}
-#define CONFIG_MMC 1
-#define CONFIG_GENERIC_MMC 1
-#define CONFIG_OMAP_HSMMC 1
-#define CONFIG_DOS_PARTITION 1
+
+/* SD/MMC */
+#define CONFIG_MMC
+#define CONFIG_GENERIC_MMC
+#define CONFIG_OMAP_HSMMC
+#define CONFIG_DOS_PARTITION
/*
* USB configuration
@@ -111,7 +105,6 @@
#define CONFIG_USB_STORAGE
#define CONGIG_CMD_STORAGE
-#define CONFIG_CMD_FAT
#ifdef CONFIG_USB_KEYBOARD
#define CONFIG_SYS_USB_EVENT_POLL
@@ -129,30 +122,29 @@
#endif /* CONFIG_USB_MUSB_AM35X */
/* commands to include */
-#define CONFIG_CMD_EXT2 /* EXT2 Support */
-#define CONFIG_CMD_FAT /* FAT support */
-#define CONFIG_CMD_JFFS2 /* JFFS2 Support */
+#define CONFIG_CMD_NAND
+#define CONFIG_CMD_CACHE
+#define CONFIG_CMD_FAT
+#define CONFIG_CMD_EXT2
#define CONFIG_CMD_EXT4
#define CONFIG_CMD_EXT4_WRITE
-
+#define CONFIG_CMD_FS_GENERIC
+#define CONFIG_CMD_PART
+#define CONFIG_CMD_ASKENV
#define CONFIG_CMD_BOOTZ
-
-#define CONFIG_CMD_I2C /* I2C serial bus support */
-#define CONFIG_CMD_MMC /* MMC support */
-#define CONFIG_CMD_NAND /* NAND support */
+#define CONFIG_CMD_I2C
+#define CONFIG_CMD_MMC
#define CONFIG_CMD_DHCP
-#undef CONFIG_CMD_PING
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_MTDPARTS
-
-#define CONFIG_SYS_NO_FLASH
+/* I2C */
#define CONFIG_SYS_I2C
#define CONFIG_SYS_OMAP24_I2C_SPEED 100000
#define CONFIG_SYS_OMAP24_I2C_SLAVE 1
#define CONFIG_SYS_I2C_OMAP34XX
-/*
- * Ethernet
- */
+/* Ethernet */
#define CONFIG_DRIVER_TI_EMAC
#define CONFIG_DRIVER_TI_EMAC_USE_RMII
#define CONFIG_MII
@@ -162,199 +154,22 @@
#define CONFIG_BOOTP_SEND_HOSTNAME
#define CONFIG_NET_RETRY_COUNT 10
-/*
- * Board NAND Info.
- */
+/* Board NAND Info. */
+#ifdef CONFIG_NAND
+#define CONFIG_NAND_OMAP_GPMC
+#define CONFIG_NAND_OMAP_GPMC_PREFETCH
+#define CONFIG_BCH
+#define CONFIG_CMD_UBI /* UBI-formated MTD partition support */
+#define CONFIG_CMD_UBIFS /* Read-only UBI volume operations */
+#define CONFIG_RBTREE /* required by CONFIG_CMD_UBI */
+#define CONFIG_LZO /* required by CONFIG_CMD_UBIFS */
#define CONFIG_SYS_NAND_ADDR NAND_BASE /* physical address */
/* to access nand */
#define CONFIG_SYS_NAND_BASE NAND_BASE /* physical address */
/* to access */
/* nand at CS0 */
-
#define CONFIG_SYS_MAX_NAND_DEVICE 1 /* Max number of */
/* NAND devices */
-#define CONFIG_JFFS2_NAND
-/* nand device jffs2 lives on */
-#define CONFIG_JFFS2_DEV "nand0"
-/* start of jffs2 partition */
-#define CONFIG_JFFS2_PART_OFFSET 0x680000
-#define CONFIG_JFFS2_PART_SIZE 0xf980000 /* sz of jffs2 part */
-
-/* Environment information */
-#define CONFIG_BOOTDELAY 10
-
-#define CONFIG_BOOTFILE "uImage"
-
-#define CONFIG_EXTRA_ENV_SETTINGS \
- "loadaddr=0x82000000\0" \
- "console=ttyO2,115200n8\0" \
- "fdtfile=am3517-evm.dtb\0" \
- "fdtaddr=0x82C00000\0" \
- "vram=16M\0" \
- "bootenv=uEnv.txt\0" \
- "cmdline=\0" \
- "optargs=\0" \
- "mmcdev=0\0" \
- "mmcpart=1\0" \
- "mmcroot=/dev/mmcblk0p2 rw\0" \
- "mmcrootfstype=ext4 rootwait fixrtc\0" \
- "mmcargs=setenv bootargs console=${console} " \
- "${optargs} " \
- "root=${mmcroot} " \
- "rootfstype=${mmcrootfstype} " \
- "${cmdline}\0" \
- "nandargs=setenv bootargs console=${console} " \
- "root=/dev/mtdblock4 rw " \
- "rootfstype=jffs2\0" \
- "loadbootenv=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${bootenv}\0"\
- "importbootenv=echo Importing environment from mmc ...; " \
- "env import -t ${loadaddr} ${filesize}\0" \
- "bootscript=echo Running bootscript from mmc ...; " \
- "source ${loadaddr}\0" \
- "loadimage=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${bootfile}\0" \
- "loadfdt=fatload mmc ${mmcdev}:${mmcpart} ${fdtaddr} ${fdtfile}\0" \
- "mmcboot=echo Booting from mmc ...; " \
- "run mmcargs; " \
- "bootz ${loadaddr} - ${fdtaddr}\0" \
- "nandboot=echo Booting from nand ...; " \
- "run nandargs; " \
- "nand read ${loadaddr} 280000 400000; " \
- "bootm ${loadaddr}\0" \
-
-#define CONFIG_BOOTCOMMAND \
- "mmc dev ${mmcdev}; if mmc rescan; then " \
- "echo SD/MMC found on device $mmcdev; " \
- "if run loadbootenv; then " \
- "run importbootenv; " \
- "fi; " \
- "echo Checking if uenvcmd is set ...; " \
- "if test -n $uenvcmd; then " \
- "echo Running uenvcmd ...; " \
- "run uenvcmd; " \
- "fi; " \
- "echo Running default loadimage ...; " \
- "setenv bootfile zImage; " \
- "if run loadimage; then " \
- "run loadfdt; " \
- "run mmcboot; " \
- "fi; " \
- "else run nandboot; fi"
-
-#define CONFIG_AUTO_COMPLETE 1
-/*
- * Miscellaneous configurable options
- */
-#define CONFIG_SYS_LONGHELP /* undef to save memory */
-#define CONFIG_SYS_HUSH_PARSER /* use "hush" command parser */
-#define CONFIG_SYS_CBSIZE 512 /* Console I/O Buffer Size */
-/* Print Buffer Size */
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \
- sizeof(CONFIG_SYS_PROMPT) + 16)
-#define CONFIG_SYS_MAXARGS 32 /* max number of command */
- /* args */
-/* Boot Argument Buffer Size */
-#define CONFIG_SYS_BARGSIZE (CONFIG_SYS_CBSIZE)
-/* memtest works on */
-#define CONFIG_SYS_MEMTEST_START (OMAP34XX_SDRC_CS0)
-#define CONFIG_SYS_MEMTEST_END (OMAP34XX_SDRC_CS0 + \
- 0x01F00000) /* 31MB */
-
-#define CONFIG_SYS_LOAD_ADDR (OMAP34XX_SDRC_CS0) /* default load */
- /* address */
-
-/*
- * AM3517 has 12 GP timers, they can be driven by the system clock
- * (12/13/16.8/19.2/38.4MHz) or by 32KHz clock. We use 13MHz (V_SCLK).
- * This rate is divided by a local divisor.
- */
-#define CONFIG_SYS_TIMERBASE OMAP34XX_GPT2
-#define CONFIG_SYS_PTV 2 /* Divisor: 2^(PTV+1) => 8 */
-
-/*-----------------------------------------------------------------------
- * Physical Memory Map
- */
-#define CONFIG_NR_DRAM_BANKS 2 /* CS1 may or may not be populated */
-#define PHYS_SDRAM_1 OMAP34XX_SDRC_CS0
-#define PHYS_SDRAM_2 OMAP34XX_SDRC_CS1
-
-/*-----------------------------------------------------------------------
- * FLASH and environment organization
- */
-
-/* **** PISMO SUPPORT *** */
-#define CONFIG_SYS_MAX_FLASH_SECT 520 /* max number of sectors */
- /* on one chip */
-#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* max number of flash banks */
-#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 2 sectors */
-
-#if defined(CONFIG_CMD_NAND)
-#define CONFIG_SYS_FLASH_BASE NAND_BASE
-#endif
-
-/* Monitor at start of flash */
-#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE
-
-#define CONFIG_NAND_OMAP_GPMC
-#define CONFIG_ENV_IS_IN_NAND 1
-#define SMNAND_ENV_OFFSET 0x260000 /* environment starts here */
-
-#define CONFIG_SYS_ENV_SECT_SIZE (128 << 10) /* 128 KiB */
-#define CONFIG_ENV_OFFSET SMNAND_ENV_OFFSET
-#define CONFIG_ENV_ADDR SMNAND_ENV_OFFSET
-
-/*-----------------------------------------------------------------------
- * CFI FLASH driver setup
- */
-/* timeout values are in ticks */
-#define CONFIG_SYS_FLASH_ERASE_TOUT (100 * CONFIG_SYS_HZ)
-#define CONFIG_SYS_FLASH_WRITE_TOUT (100 * CONFIG_SYS_HZ)
-
-/* Flash banks JFFS2 should use */
-#define CONFIG_SYS_MAX_MTD_BANKS (CONFIG_SYS_MAX_FLASH_BANKS + \
- CONFIG_SYS_MAX_NAND_DEVICE)
-#define CONFIG_SYS_JFFS2_MEM_NAND
-/* use flash_info[2] */
-#define CONFIG_SYS_JFFS2_FIRST_BANK CONFIG_SYS_MAX_FLASH_BANKS
-#define CONFIG_SYS_JFFS2_NUM_BANKS 1
-
-#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1
-#define CONFIG_SYS_INIT_RAM_ADDR 0x4020f800
-#define CONFIG_SYS_INIT_RAM_SIZE 0x800
-#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_INIT_RAM_ADDR + \
- CONFIG_SYS_INIT_RAM_SIZE - \
- GENERATED_GBL_DATA_SIZE)
-
-/* Defines for SPL */
-#define CONFIG_SPL_FRAMEWORK
-#define CONFIG_SPL_BOARD_INIT
-#define CONFIG_SPL_NAND_SIMPLE
-#define CONFIG_SPL_TEXT_BASE 0x40200000
-#define CONFIG_SPL_MAX_SIZE (64 * 1024)
-
-#define CONFIG_SPL_BSS_START_ADDR 0x80000000
-#define CONFIG_SPL_BSS_MAX_SIZE 0x80000 /* 512 KB */
-
-#define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR 0x300 /* address 0x60000 */
-#define CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS 0x200 /* 256 KB */
-#define CONFIG_SYS_MMCSD_FS_BOOT_PARTITION 1
-#define CONFIG_SPL_FS_LOAD_PAYLOAD_NAME "u-boot.img"
-
-#define CONFIG_SPL_LIBCOMMON_SUPPORT
-#define CONFIG_SPL_LIBDISK_SUPPORT
-#define CONFIG_SPL_I2C_SUPPORT
-#define CONFIG_SPL_LIBGENERIC_SUPPORT
-#define CONFIG_SPL_MMC_SUPPORT
-#define CONFIG_SPL_FAT_SUPPORT
-#define CONFIG_SPL_SERIAL_SUPPORT
-#define CONFIG_SPL_NAND_SUPPORT
-#define CONFIG_SPL_NAND_BASE
-#define CONFIG_SPL_NAND_DRIVERS
-#define CONFIG_SPL_NAND_ECC
-#define CONFIG_SPL_POWER_SUPPORT
-#define CONFIG_SPL_LDSCRIPT "$(CPUDIR)/omap-common/u-boot-spl.lds"
-
-/* NAND boot config */
-#define CONFIG_BCH
#define CONFIG_SYS_NAND_BUSWIDTH_16BIT
#define CONFIG_SYS_NAND_5_ADDR_CYCLE
#define CONFIG_SYS_NAND_PAGE_COUNT 64
@@ -376,15 +191,193 @@
#define CONFIG_SYS_NAND_MAX_ECCPOS 56
#define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_TEXT_BASE
#define CONFIG_SYS_NAND_U_BOOT_OFFS 0x80000
+#define CONFIG_MTD_PARTITIONS /* required for UBI partition support */
+#define CONFIG_MTD_DEVICE /* needed for mtdparts commands */
+/* NAND block size is 128 KiB. Synchronize these values with
+ * corresponding Device Tree entries in Linux:
+ * MLO(SPL) 4 * NAND_BLOCK_SIZE = 512 KiB @ 0x000000
+ * U-Boot 15 * NAND_BLOCK_SIZE = 1920 KiB @ 0x080000
+ * U-Boot environment 2 * NAND_BLOCK_SIZE = 256 KiB @ 0x260000
+ * Kernel 64 * NAND_BLOCK_SIZE = 8 MiB @ 0x2A0000
+ * DTB 4 * NAND_BLOCK_SIZE = 512 KiB @ 0xAA0000
+ * RootFS Remaining Flash Space @ 0xB20000
+ */
+#define MTDIDS_DEFAULT "nand0=omap2-nand.0"
+#define MTDPARTS_DEFAULT "mtdparts=omap2-nand.0:" \
+ "512k(MLO)," \
+ "1920k(u-boot)," \
+ "256k(u-boot-env)," \
+ "8m(kernel)," \
+ "512k(dtb)," \
+ "-(rootfs)"
+#else
+#define MTDIDS_DEFAULT
+#define MTDPARTS_DEFAULT
+#endif /* CONFIG_NAND */
+
+/* Environment information */
+#define CONFIG_BOOTDELAY 10
+
+#define CONFIG_BOOTFILE "uImage"
+
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ "loadaddr=0x82000000\0" \
+ "console=ttyO2,115200n8\0" \
+ "fdtfile=am3517-evm.dtb\0" \
+ "fdtaddr=0x82C00000\0" \
+ "vram=16M\0" \
+ "bootenv=uEnv.txt\0" \
+ "cmdline=\0" \
+ "optargs=\0" \
+ "mtdids=" MTDIDS_DEFAULT "\0" \
+ "mtdparts=" MTDPARTS_DEFAULT "\0" \
+ "mmcdev=0\0" \
+ "mmcpart=1\0" \
+ "mmcroot=/dev/mmcblk0p2 rw\0" \
+ "mmcrootfstype=ext4 rootwait fixrtc\0" \
+ "mmcargs=setenv bootargs console=${console} " \
+ "${mtdparts} " \
+ "${optargs} " \
+ "root=${mmcroot} " \
+ "rootfstype=${mmcrootfstype} " \
+ "${cmdline}\0" \
+ "nandargs=setenv bootargs console=${console} " \
+ "${mtdparts} " \
+ "${optargs} " \
+ "root=ubi0:rootfs rw ubi.mtd=rootfs " \
+ "rootfstype=ubifs rootwait " \
+ "${cmdline}\0" \
+ "loadbootenv=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${bootenv}\0"\
+ "importbootenv=echo Importing environment from mmc ...; " \
+ "env import -t ${loadaddr} ${filesize}\0" \
+ "bootscript=echo Running bootscript from mmc ...; " \
+ "source ${loadaddr}\0" \
+ "loadimage=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${bootfile}\0" \
+ "loadfdt=fatload mmc ${mmcdev}:${mmcpart} ${fdtaddr} ${fdtfile}\0" \
+ "mmcboot=echo Booting from mmc ...; " \
+ "run mmcargs; " \
+ "bootz ${loadaddr} - ${fdtaddr}\0" \
+ "nandboot=echo Booting from nand ...; " \
+ "run nandargs; " \
+ "nand read ${loadaddr} 2a0000 800000; " \
+ "nand read ${fdtaddr} aa0000 80000; " \
+ "bootm ${loadaddr} - ${fdtaddr}\0" \
+
+#define CONFIG_BOOTCOMMAND \
+ "mmc dev ${mmcdev}; if mmc rescan; then " \
+ "echo SD/MMC found on device $mmcdev; " \
+ "if run loadbootenv; then " \
+ "run importbootenv; " \
+ "fi; " \
+ "echo Checking if uenvcmd is set ...; " \
+ "if test -n $uenvcmd; then " \
+ "echo Running uenvcmd ...; " \
+ "run uenvcmd; " \
+ "fi; " \
+ "echo Running default loadimage ...; " \
+ "setenv bootfile zImage; " \
+ "if run loadimage; then " \
+ "run loadfdt; " \
+ "run mmcboot; " \
+ "fi; " \
+ "else run nandboot; fi"
+
+/* Miscellaneous configurable options */
+#define CONFIG_AUTO_COMPLETE
+#define CONFIG_CMDLINE_EDITING
+#define CONFIG_VERSION_VARIABLE
+#define CONFIG_SYS_LONGHELP
+#define CONFIG_SYS_HUSH_PARSER
+#define CONFIG_PARTITION_UUIDS
+
+/* We set the max number of command args high to avoid HUSH bugs. */
+#define CONFIG_SYS_MAXARGS 64
+
+/* Console I/O Buffer Size */
+#define CONFIG_SYS_CBSIZE 512
+/* Print Buffer Size */
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE \
+ + sizeof(CONFIG_SYS_PROMPT) + 16)
+/* Boot Argument Buffer Size */
+#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
+
+/* memtest works on */
+#define CONFIG_SYS_MEMTEST_START (OMAP34XX_SDRC_CS0)
+#define CONFIG_SYS_MEMTEST_END (OMAP34XX_SDRC_CS0 + \
+ 0x01F00000) /* 31MB */
+
+#define CONFIG_SYS_LOAD_ADDR (OMAP34XX_SDRC_CS0) /* default load */
+ /* address */
/*
- * 1MB into the SDRAM to allow for SPL's bss at the beginning of SDRAM
- * 64 bytes before this address should be set aside for u-boot.img's
- * header. That is 0x800FFFC0--0x80100000 should not be used for any
- * other needs.
+ * AM3517 has 12 GP timers, they can be driven by the system clock
+ * (12/13/16.8/19.2/38.4MHz) or by 32KHz clock. We use 13MHz (V_SCLK).
+ * This rate is divided by a local divisor.
*/
-#define CONFIG_SYS_TEXT_BASE 0x80100000
-#define CONFIG_SYS_SPL_MALLOC_START 0x80208000
-#define CONFIG_SYS_SPL_MALLOC_SIZE 0x100000
+#define CONFIG_SYS_TIMERBASE OMAP34XX_GPT2
+#define CONFIG_SYS_PTV 2 /* Divisor: 2^(PTV+1) => 8 */
+
+/* Physical Memory Map */
+#define PHYS_SDRAM_1 OMAP34XX_SDRC_CS0
+#define PHYS_SDRAM_2 OMAP34XX_SDRC_CS1
+#define CONFIG_SYS_CS0_SIZE (256 * 1024 * 1024)
+#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1
+#define CONFIG_SYS_INIT_RAM_ADDR 0x4020f800
+#define CONFIG_SYS_INIT_RAM_SIZE 0x800
+#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_INIT_RAM_ADDR + \
+ CONFIG_SYS_INIT_RAM_SIZE - \
+ GENERATED_GBL_DATA_SIZE)
+
+/* FLASH and environment organization */
+
+/* **** PISMO SUPPORT *** */
+#define CONFIG_SYS_MAX_FLASH_SECT 520 /* max number of sectors */
+ /* on one chip */
+#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* max number of flash banks */
+#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 2 sectors */
+
+#if defined(CONFIG_NAND)
+#define CONFIG_SYS_FLASH_BASE NAND_BASE
+#endif
+
+/* Monitor at start of flash */
+#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE
+
+#define CONFIG_SYS_ENV_SECT_SIZE (128 << 10) /* 128 KiB */
+#define CONFIG_ENV_SIZE CONFIG_SYS_ENV_SECT_SIZE
+#define SMNAND_ENV_OFFSET 0x260000 /* environment starts here */
+#define CONFIG_ENV_OFFSET SMNAND_ENV_OFFSET
+#define CONFIG_ENV_ADDR SMNAND_ENV_OFFSET
+#define CONFIG_ENV_IS_IN_NAND
+
+/* Defines for SPL */
+#define CONFIG_SPL_FRAMEWORK
+#define CONFIG_SPL_BOARD_INIT
+#define CONFIG_SPL_NAND_SIMPLE
+#define CONFIG_SPL_TEXT_BASE 0x40200000
+#define CONFIG_SPL_MAX_SIZE (64 * 1024)
+
+#define CONFIG_SPL_BSS_START_ADDR 0x80000000
+#define CONFIG_SPL_BSS_MAX_SIZE 0x80000 /* 512 KB */
+
+#define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR 0x300 /* address 0x60000 */
+#define CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS 0x200 /* 256 KB */
+#define CONFIG_SYS_MMCSD_FS_BOOT_PARTITION 1
+#define CONFIG_SPL_FS_LOAD_PAYLOAD_NAME "u-boot.img"
+
+#define CONFIG_SPL_LIBCOMMON_SUPPORT
+#define CONFIG_SPL_LIBDISK_SUPPORT
+#define CONFIG_SPL_I2C_SUPPORT
+#define CONFIG_SPL_LIBGENERIC_SUPPORT
+#define CONFIG_SPL_MMC_SUPPORT
+#define CONFIG_SPL_FAT_SUPPORT
+#define CONFIG_SPL_SERIAL_SUPPORT
+#define CONFIG_SPL_NAND_SUPPORT
+#define CONFIG_SPL_NAND_BASE
+#define CONFIG_SPL_NAND_DRIVERS
+#define CONFIG_SPL_NAND_ECC
+#define CONFIG_SPL_MTD_SUPPORT
+#define CONFIG_SPL_POWER_SUPPORT
+#define CONFIG_SPL_LDSCRIPT "$(CPUDIR)/omap-common/u-boot-spl.lds"
#endif /* __CONFIG_H */