mtd: nand: omap: add CONFIG_NAND_OMAP_ECCSCHEME for selection of ecc-scheme
This patch adds new CONFIG_NAND_OMAP_ECCSCHEME, replacing other distributed
CONFIG_xx used for selecting NAND ecc-schemes.
This patch aims at solving following issues.
1) Currently ecc-scheme is tied to SoC platform, which prevents user to select
other ecc-schemes also supported in hardware. like;
- most of OMAP3 SoC platforms use only 1-bit Hamming ecc-scheme, inspite
the fact that they can use higher ecc-schemes like 8-bit ecc-schemes with
software based error detection (OMAP_ECC_BCH4_CODE_HW_DETECTION_SW).
- most of AM33xx SoC plaforms use 8-bit BCH ecc-scheme for now, but hardware
supports BCH16 ecc-scheme also.
2) Different platforms use different CONFIG_xx to select ecc-schemes, which
adds confusion for user while migrating platforms.
- *CONFIG_NAND_OMAP_ELM* which enables ELM hardware engine, selects only
8-bit BCH ecc-scheme with h/w based error-correction (OMAP_ECC_BCH8_CODE_HW)
whereas ELM hardware engine supports other ecc-schemes also like; BCH4,
and BCH16 (in future).
- *CONFIG_NAND_OMAP_BCH8* selects 8-bit BCH ecc-scheme with s/w based error
correction (OMAP_ECC_BCH8_CODE_HW_DETECTION_SW).
- *CONFIG_SPL_NAND_SOFTECC* selects 1-bit Hamming ecc-scheme using s/w library
Thus adding new *CONFIG_NAND_OMAP_ECCSCHEME* de-couples ecc-scheme dependency
on SoC platform and NAND driver. And user can select ecc-scheme independently
foreach board.
However, selection some hardware based ecc-schemes (OMAP_ECC_BCHx_CODE_HW) still
depends on presence of ELM hardware engine on SoC. (Refer doc/README.nand)
Signed-off-by: Pekon Gupta <pekon@ti.com>
diff --git a/doc/README.nand b/doc/README.nand
index 487548f..b91f198 100644
--- a/doc/README.nand
+++ b/doc/README.nand
@@ -208,6 +208,29 @@
detection. However ECC calculation on such plaforms would still be
done by GPMC controller.
+ CONFIG_NAND_OMAP_ECCSCHEME
+ On OMAP platforms, this CONFIG specifies NAND ECC scheme.
+ It can take following values:
+ OMAP_ECC_HAM1_CODE_SW
+ 1-bit Hamming code using software lib.
+ (for legacy devices only)
+ OMAP_ECC_HAM1_CODE_HW
+ 1-bit Hamming code using GPMC hardware.
+ (for legacy devices only)
+ OMAP_ECC_BCH4_CODE_HW_DETECTION_SW
+ 4-bit BCH code (unsupported)
+ OMAP_ECC_BCH4_CODE_HW
+ 4-bit BCH code (unsupported)
+ OMAP_ECC_BCH8_CODE_HW_DETECTION_SW
+ 8-bit BCH code with
+ - ecc calculation using GPMC hardware engine,
+ - error detection using software library.
+ - requires CONFIG_BCH to enable software BCH library
+ (For legacy device which do not have ELM h/w engine)
+ OMAP_ECC_BCH8_CODE_HW
+ 8-bit BCH code with
+ - ecc calculation using GPMC hardware engine,
+ - error detection using ELM hardware engine.
NOTE:
=====
diff --git a/doc/README.omap3 b/doc/README.omap3
index 1fbe79d..a62c357 100644
--- a/doc/README.omap3
+++ b/doc/README.omap3
@@ -161,8 +161,7 @@
To enable hardware assisted BCH8 (8-bit BCH [Bose, Chaudhuri, Hocquenghem]) on
OMAP3 devices we can use the BCH library in lib/bch.c. To do so add CONFIG_BCH
-to enable the library and CONFIG_NAND_OMAP_BCH8 to to enable hardware assisted
-syndrom generation to your board config.
+and set CONFIG_NAND_OMAP_ECCSCHEME=5 (refer README.nand) for selecting BCH8_SW.
The NAND OOB layout is the same as in linux kernel, if the linux kernel BCH8
implementation for OMAP3 works for you so the u-boot version should also.
When you require the SPL to read with BCH8 there are two more configs to
diff --git a/drivers/mtd/nand/omap_gpmc.c b/drivers/mtd/nand/omap_gpmc.c
index e6b289d..5e7e6b3 100644
--- a/drivers/mtd/nand/omap_gpmc.c
+++ b/drivers/mtd/nand/omap_gpmc.c
@@ -1004,18 +1004,13 @@
nand->ecc.layout = &omap_ecclayout;
/* select ECC scheme */
-#if defined(CONFIG_NAND_OMAP_ELM)
- err = omap_select_ecc_scheme(nand, OMAP_ECC_BCH8_CODE_HW,
+#if defined(CONFIG_NAND_OMAP_ECCSCHEME)
+ err = omap_select_ecc_scheme(nand, CONFIG_NAND_OMAP_ECCSCHEME,
CONFIG_SYS_NAND_PAGE_SIZE, CONFIG_SYS_NAND_OOBSIZE);
-#elif defined(CONFIG_NAND_OMAP_BCH8)
- err = omap_select_ecc_scheme(nand, OMAP_ECC_BCH8_CODE_HW_DETECTION_SW,
- CONFIG_SYS_NAND_PAGE_SIZE, CONFIG_SYS_NAND_OOBSIZE);
-#elif !defined(CONFIG_SPL_BUILD) || defined(CONFIG_SPL_NAND_SOFTECC)
+#else
+ /* pagesize and oobsize are not required to configure sw ecc-scheme */
err = omap_select_ecc_scheme(nand, OMAP_ECC_HAM1_CODE_SW,
0, 0);
-#else
- err = omap_select_ecc_scheme(nand, OMAP_ECC_HAM1_CODE_HW,
- CONFIG_SYS_NAND_PAGE_SIZE, CONFIG_SYS_NAND_OOBSIZE);
#endif
if (err)
return err;
diff --git a/include/configs/am335x_evm.h b/include/configs/am335x_evm.h
index 73d8b4d..1d59167 100644
--- a/include/configs/am335x_evm.h
+++ b/include/configs/am335x_evm.h
@@ -240,7 +240,8 @@
#define CONFIG_SYS_NAND_ECCSIZE 512
#define CONFIG_SYS_NAND_ECCBYTES 14
-
+#define CONFIG_SYS_NAND_ONFI_DETECTION
+#define CONFIG_NAND_OMAP_ECCSCHEME OMAP_ECC_BCH8_CODE_HW
#define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_TEXT_BASE
#define CONFIG_SYS_NAND_U_BOOT_OFFS 0x80000
#endif
diff --git a/include/configs/am335x_igep0033.h b/include/configs/am335x_igep0033.h
index 88ced73..115d1b3 100644
--- a/include/configs/am335x_igep0033.h
+++ b/include/configs/am335x_igep0033.h
@@ -264,6 +264,7 @@
#define CONFIG_SYS_NAND_ECCSIZE 512
#define CONFIG_SYS_NAND_ECCBYTES 14
+#define CONFIG_NAND_OMAP_ECCSCHEME OMAP_ECC_BCH8_CODE_HW
#define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_TEXT_BASE
diff --git a/include/configs/am3517_crane.h b/include/configs/am3517_crane.h
index c5e67bf..b24ef54 100644
--- a/include/configs/am3517_crane.h
+++ b/include/configs/am3517_crane.h
@@ -340,6 +340,7 @@
10, 11, 12, 13}
#define CONFIG_SYS_NAND_ECCSIZE 512
#define CONFIG_SYS_NAND_ECCBYTES 3
+#define CONFIG_NAND_OMAP_ECCSCHEME OMAP_ECC_HAM1_CODE_HW
#define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_TEXT_BASE
#define CONFIG_SYS_NAND_U_BOOT_OFFS 0x80000
diff --git a/include/configs/am3517_evm.h b/include/configs/am3517_evm.h
index 5ff65c6..f13fd70 100644
--- a/include/configs/am3517_evm.h
+++ b/include/configs/am3517_evm.h
@@ -334,6 +334,7 @@
10, 11, 12, 13}
#define CONFIG_SYS_NAND_ECCSIZE 512
#define CONFIG_SYS_NAND_ECCBYTES 3
+#define CONFIG_NAND_OMAP_ECCSCHEME OMAP_ECC_HAM1_CODE_HW
#define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_TEXT_BASE
#define CONFIG_SYS_NAND_U_BOOT_OFFS 0x80000
diff --git a/include/configs/devkit8000.h b/include/configs/devkit8000.h
index 8343891..13315dc 100644
--- a/include/configs/devkit8000.h
+++ b/include/configs/devkit8000.h
@@ -327,6 +327,7 @@
#define CONFIG_SYS_NAND_ECCSIZE 512
#define CONFIG_SYS_NAND_ECCBYTES 3
+#define CONFIG_NAND_OMAP_ECCSCHEME OMAP_ECC_HAM1_CODE_HW
#define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_TEXT_BASE
diff --git a/include/configs/mcx.h b/include/configs/mcx.h
index 4619dfb..56102f5 100644
--- a/include/configs/mcx.h
+++ b/include/configs/mcx.h
@@ -353,7 +353,6 @@
#define CONFIG_SPL_FRAMEWORK
#define CONFIG_SPL_BOARD_INIT
#define CONFIG_SPL_NAND_SIMPLE
-#define CONFIG_SPL_NAND_SOFTECC
#define CONFIG_SPL_LIBCOMMON_SUPPORT
#define CONFIG_SPL_LIBDISK_SUPPORT
@@ -395,6 +394,7 @@
56, 57, 58, 59, 60, 61, 62, 63}
#define CONFIG_SYS_NAND_ECCSIZE 256
#define CONFIG_SYS_NAND_ECCBYTES 3
+#define CONFIG_NAND_OMAP_ECCSCHEME OMAP_ECC_HAM1_CODE_SW
#define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_TEXT_BASE
diff --git a/include/configs/omap3_beagle.h b/include/configs/omap3_beagle.h
index 47d9902..8b68635 100644
--- a/include/configs/omap3_beagle.h
+++ b/include/configs/omap3_beagle.h
@@ -432,6 +432,7 @@
10, 11, 12, 13}
#define CONFIG_SYS_NAND_ECCSIZE 512
#define CONFIG_SYS_NAND_ECCBYTES 3
+#define CONFIG_NAND_OMAP_ECCSCHEME OMAP_ECC_HAM1_CODE_HW
#define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_TEXT_BASE
#define CONFIG_SYS_NAND_U_BOOT_OFFS 0x80000
diff --git a/include/configs/omap3_evm.h b/include/configs/omap3_evm.h
index 3ace8bb..b7638fb 100644
--- a/include/configs/omap3_evm.h
+++ b/include/configs/omap3_evm.h
@@ -107,6 +107,7 @@
10, 11, 12, 13}
#define CONFIG_SYS_NAND_ECCSIZE 512
#define CONFIG_SYS_NAND_ECCBYTES 3
+#define CONFIG_NAND_OMAP_ECCSCHEME OMAP_ECC_HAM1_CODE_HW
#define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_TEXT_BASE
#define CONFIG_SYS_NAND_U_BOOT_OFFS 0x80000
diff --git a/include/configs/omap3_evm_quick_nand.h b/include/configs/omap3_evm_quick_nand.h
index 9ecd70d..4427e88 100644
--- a/include/configs/omap3_evm_quick_nand.h
+++ b/include/configs/omap3_evm_quick_nand.h
@@ -86,6 +86,7 @@
10, 11, 12, 13}
#define CONFIG_SYS_NAND_ECCSIZE 512
#define CONFIG_SYS_NAND_ECCBYTES 3
+#define CONFIG_NAND_OMAP_ECCSCHEME OMAP_ECC_HAM1_CODE_HW
#define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_TEXT_BASE
#define CONFIG_SYS_NAND_U_BOOT_OFFS 0x80000
diff --git a/include/configs/omap3_igep00x0.h b/include/configs/omap3_igep00x0.h
index ac36ac6..cdaa9ba 100644
--- a/include/configs/omap3_igep00x0.h
+++ b/include/configs/omap3_igep00x0.h
@@ -362,6 +362,7 @@
10, 11, 12, 13}
#define CONFIG_SYS_NAND_ECCSIZE 512
#define CONFIG_SYS_NAND_ECCBYTES 3
+#define CONFIG_NAND_OMAP_ECCSCHEME OMAP_ECC_HAM1_CODE_HW
#define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_TEXT_BASE
#define CONFIG_SYS_NAND_U_BOOT_OFFS 0x80000
#endif
diff --git a/include/configs/omap3_overo.h b/include/configs/omap3_overo.h
index 4641694..00d7c6c 100644
--- a/include/configs/omap3_overo.h
+++ b/include/configs/omap3_overo.h
@@ -325,6 +325,7 @@
10, 11, 12, 13}
#define CONFIG_SYS_NAND_ECCSIZE 512
#define CONFIG_SYS_NAND_ECCBYTES 3
+#define CONFIG_NAND_OMAP_ECCSCHEME OMAP_ECC_HAM1_CODE_HW
#define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_TEXT_BASE
#define CONFIG_SYS_NAND_U_BOOT_OFFS 0x80000
diff --git a/include/configs/siemens-am33x-common.h b/include/configs/siemens-am33x-common.h
index f3b4197..e394478 100644
--- a/include/configs/siemens-am33x-common.h
+++ b/include/configs/siemens-am33x-common.h
@@ -196,6 +196,7 @@
#define CONFIG_SYS_NAND_ECCSIZE 512
#define CONFIG_SYS_NAND_ECCBYTES 14
+#define CONFIG_NAND_OMAP_ECCSCHEME OMAP_ECC_BCH8_CODE_HW
#define CONFIG_SYS_NAND_ECCSTEPS 4
#define CONFIG_SYS_NAND_ECCTOTAL (CONFIG_SYS_NAND_ECCBYTES * \
diff --git a/include/configs/tam3517-common.h b/include/configs/tam3517-common.h
index 683bc54..48698b5 100644
--- a/include/configs/tam3517-common.h
+++ b/include/configs/tam3517-common.h
@@ -225,7 +225,6 @@
#define CONFIG_SPL_BOARD_INIT
#define CONFIG_SPL_CONSOLE
#define CONFIG_SPL_NAND_SIMPLE
-#define CONFIG_SPL_NAND_SOFTECC
#define CONFIG_SPL_NAND_WORKSPACE 0x8f07f000 /* below BSS */
#define CONFIG_SPL_LIBCOMMON_SUPPORT
@@ -262,6 +261,7 @@
56, 57, 58, 59, 60, 61, 62, 63}
#define CONFIG_SYS_NAND_ECCSIZE 256
#define CONFIG_SYS_NAND_ECCBYTES 3
+#define CONFIG_NAND_OMAP_ECCSCHEME OMAP_ECC_HAM1_CODE_SW
#define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_TEXT_BASE
diff --git a/include/configs/tricorder.h b/include/configs/tricorder.h
index 590eab7..3ca1fd0 100644
--- a/include/configs/tricorder.h
+++ b/include/configs/tricorder.h
@@ -138,7 +138,6 @@
#define CONFIG_SYS_MAX_NAND_DEVICE 1 /* Max number of NAND */
/* devices */
-#define CONFIG_NAND_OMAP_BCH8
#define CONFIG_BCH
#define CONFIG_SYS_NAND_MAX_OOBFREE 2
#define CONFIG_SYS_NAND_MAX_ECCPOS 56
@@ -376,6 +375,7 @@
#define CONFIG_SYS_NAND_ECCSIZE 512
#define CONFIG_SYS_NAND_ECCBYTES 13
+#define CONFIG_NAND_OMAP_ECCSCHEME OMAP_ECC_BCH8_CODE_HW_DETECTION_SW
#define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_TEXT_BASE