fdt: update bcm283x device tree sources to Linux 4.14 state
Upstream Linux has received a few device tree updates to the RPi
which we should propagate into the builtin U-Boot one as well to
gain hardware support.
This patch bumps the dts files to their 4.14 Linux counterparts
with the exception of sdhost on 32bit RPi versions. There we stay
with iproc as the sdhost driver is missing in U-Boot.
Signed-off-by: Alexander Graf <agraf@suse.de>
diff --git a/arch/arm/dts/bcm2835-rpi-a-plus.dts b/arch/arm/dts/bcm2835-rpi-a-plus.dts
index 35ff4e7..9f86649 100644
--- a/arch/arm/dts/bcm2835-rpi-a-plus.dts
+++ b/arch/arm/dts/bcm2835-rpi-a-plus.dts
@@ -1,6 +1,7 @@
/dts-v1/;
#include "bcm2835.dtsi"
#include "bcm2835-rpi.dtsi"
+#include "bcm283x-rpi-usb-host.dtsi"
/ {
compatible = "raspberrypi,model-a-plus", "brcm,bcm2835";
@@ -21,7 +22,72 @@
};
&gpio {
- pinctrl-0 = <&gpioout &alt0 &i2s_alt0 &alt3>;
+ /*
+ * This is based on the unreleased schematic for the Model A+.
+ *
+ * Legend:
+ * "NC" = not connected (no rail from the SoC)
+ * "FOO" = GPIO line named "FOO" on the schematic
+ * "FOO_N" = GPIO line named "FOO" on schematic, active low
+ */
+ gpio-line-names = "SDA0",
+ "SCL0",
+ "SDA1",
+ "SCL1",
+ "GPIO_GCLK",
+ "GPIO5",
+ "GPIO6",
+ "SPI_CE1_N",
+ "SPI_CE0_N",
+ "SPI_MISO",
+ "SPI_MOSI",
+ "SPI_SCLK",
+ "GPIO12",
+ "GPIO13",
+ /* Serial port */
+ "TXD0",
+ "RXD0",
+ "GPIO16",
+ "GPIO17",
+ "GPIO18",
+ "GPIO19",
+ "GPIO20",
+ "GPIO21",
+ "GPIO22",
+ "GPIO23",
+ "GPIO24",
+ "GPIO25",
+ "GPIO26",
+ "GPIO27",
+ "SDA0",
+ "SCL0",
+ "NC", /* GPIO30 */
+ "NC", /* GPIO31 */
+ "CAM_GPIO1", /* GPIO32 */
+ "NC", /* GPIO33 */
+ "NC", /* GPIO34 */
+ "PWR_LOW_N", /* GPIO35 */
+ "NC", /* GPIO36 */
+ "NC", /* GPIO37 */
+ "USB_LIMIT", /* GPIO38 */
+ "NC", /* GPIO39 */
+ "PWM0_OUT", /* GPIO40 */
+ "CAM_GPIO0", /* GPIO41 */
+ "NC", /* GPIO42 */
+ "NC", /* GPIO43 */
+ "NC", /* GPIO44 */
+ "PWM1_OUT", /* GPIO45 */
+ "HDMI_HPD_N",
+ "STATUS_LED",
+ /* Used by SD Card */
+ "SD_CLK_R",
+ "SD_CMD_R",
+ "SD_DATA0_R",
+ "SD_DATA1_R",
+ "SD_DATA2_R",
+ "SD_DATA3_R";
+
+ pinctrl-0 = <&gpioout &alt0 &i2s_alt0>;
/* I2S interface */
i2s_alt0: i2s_alt0 {
@@ -33,3 +99,9 @@
&hdmi {
hpd-gpios = <&gpio 46 GPIO_ACTIVE_LOW>;
};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_gpio14>;
+ status = "okay";
+};
diff --git a/arch/arm/dts/bcm2835-rpi-a.dts b/arch/arm/dts/bcm2835-rpi-a.dts
index 306a84e..4b1af06 100644
--- a/arch/arm/dts/bcm2835-rpi-a.dts
+++ b/arch/arm/dts/bcm2835-rpi-a.dts
@@ -1,6 +1,7 @@
/dts-v1/;
#include "bcm2835.dtsi"
#include "bcm2835-rpi.dtsi"
+#include "bcm283x-rpi-usb-host.dtsi"
/ {
compatible = "raspberrypi,model-a", "brcm,bcm2835";
@@ -14,7 +15,74 @@
};
&gpio {
- pinctrl-0 = <&gpioout &alt0 &i2s_alt2 &alt3>;
+ /*
+ * Taken from Raspberry-Pi-Rev-1.0-Model-AB-Schematics.pdf
+ * RPI00021 sheet 02
+ *
+ * Legend:
+ * "NC" = not connected (no rail from the SoC)
+ * "FOO" = GPIO line named "FOO" on the schematic
+ * "FOO_N" = GPIO line named "FOO" on schematic, active low
+ */
+ gpio-line-names = "SDA0",
+ "SCL0",
+ "SDA1",
+ "SCL1",
+ "GPIO_GCLK",
+ "CAM_GPIO1",
+ "LAN_RUN",
+ "SPI_CE1_N",
+ "SPI_CE0_N",
+ "SPI_MISO",
+ "SPI_MOSI",
+ "SPI_SCLK",
+ "NC", /* GPIO12 */
+ "NC", /* GPIO13 */
+ /* Serial port */
+ "TXD0",
+ "RXD0",
+ "STATUS_LED_N",
+ "GPIO17",
+ "GPIO18",
+ "NC", /* GPIO19 */
+ "NC", /* GPIO20 */
+ "GPIO21",
+ "GPIO22",
+ "GPIO23",
+ "GPIO24",
+ "GPIO25",
+ "NC", /* GPIO26 */
+ "CAM_GPIO0",
+ /* Binary number representing build/revision */
+ "CONFIG0",
+ "CONFIG1",
+ "CONFIG2",
+ "CONFIG3",
+ "NC", /* GPIO32 */
+ "NC", /* GPIO33 */
+ "NC", /* GPIO34 */
+ "NC", /* GPIO35 */
+ "NC", /* GPIO36 */
+ "NC", /* GPIO37 */
+ "NC", /* GPIO38 */
+ "NC", /* GPIO39 */
+ "PWM0_OUT",
+ "NC", /* GPIO41 */
+ "NC", /* GPIO42 */
+ "NC", /* GPIO43 */
+ "NC", /* GPIO44 */
+ "PWM1_OUT",
+ "HDMI_HPD_P",
+ "SD_CARD_DET",
+ /* Used by SD Card */
+ "SD_CLK_R",
+ "SD_CMD_R",
+ "SD_DATA0_R",
+ "SD_DATA1_R",
+ "SD_DATA2_R",
+ "SD_DATA3_R";
+
+ pinctrl-0 = <&gpioout &alt0 &i2s_alt2>;
/* I2S interface */
i2s_alt2: i2s_alt2 {
@@ -26,3 +94,9 @@
&hdmi {
hpd-gpios = <&gpio 46 GPIO_ACTIVE_HIGH>;
};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_gpio14>;
+ status = "okay";
+};
diff --git a/arch/arm/dts/bcm2835-rpi-b-plus.dts b/arch/arm/dts/bcm2835-rpi-b-plus.dts
index d5fdb8e..a846f1e 100644
--- a/arch/arm/dts/bcm2835-rpi-b-plus.dts
+++ b/arch/arm/dts/bcm2835-rpi-b-plus.dts
@@ -2,6 +2,7 @@
#include "bcm2835.dtsi"
#include "bcm2835-rpi.dtsi"
#include "bcm283x-rpi-smsc9514.dtsi"
+#include "bcm283x-rpi-usb-host.dtsi"
/ {
compatible = "raspberrypi,model-b-plus", "brcm,bcm2835";
@@ -22,7 +23,73 @@
};
&gpio {
- pinctrl-0 = <&gpioout &alt0 &i2s_alt0 &alt3>;
+ /*
+ * Taken from Raspberry-Pi-B-Plus-V1.2-Schematics.pdf
+ * RPI-BPLUS sheet 1
+ *
+ * Legend:
+ * "NC" = not connected (no rail from the SoC)
+ * "FOO" = GPIO line named "FOO" on the schematic
+ * "FOO_N" = GPIO line named "FOO" on schematic, active low
+ */
+ gpio-line-names = "SDA0",
+ "SCL0",
+ "SDA1",
+ "SCL1",
+ "GPIO_GCLK",
+ "GPIO5",
+ "GPIO6",
+ "SPI_CE1_N",
+ "SPI_CE0_N",
+ "SPI_MISO",
+ "SPI_MOSI",
+ "SPI_SCLK",
+ "GPIO12",
+ "GPIO13",
+ /* Serial port */
+ "TXD0",
+ "RXD0",
+ "GPIO16",
+ "GPIO17",
+ "GPIO18",
+ "GPIO19",
+ "GPIO20",
+ "GPIO21",
+ "GPIO22",
+ "GPIO23",
+ "GPIO24",
+ "GPIO25",
+ "GPIO26",
+ "GPIO27",
+ "SDA0",
+ "SCL0",
+ "NC", /* GPIO30 */
+ "LAN_RUN", /* GPIO31 */
+ "CAM_GPIO1", /* GPIO32 */
+ "NC", /* GPIO33 */
+ "NC", /* GPIO34 */
+ "PWR_LOW_N", /* GPIO35 */
+ "NC", /* GPIO36 */
+ "NC", /* GPIO37 */
+ "USB_LIMIT", /* GPIO38 */
+ "NC", /* GPIO39 */
+ "PWM0_OUT", /* GPIO40 */
+ "CAM_GPIO0", /* GPIO41 */
+ "NC", /* GPIO42 */
+ "NC", /* GPIO43 */
+ "ETHCLK", /* GPIO44 */
+ "PWM1_OUT", /* GPIO45 */
+ "HDMI_HPD_N",
+ "STATUS_LED",
+ /* Used by SD Card */
+ "SD_CLK_R",
+ "SD_CMD_R",
+ "SD_DATA0_R",
+ "SD_DATA1_R",
+ "SD_DATA2_R",
+ "SD_DATA3_R";
+
+ pinctrl-0 = <&gpioout &alt0 &i2s_alt0>;
/* I2S interface */
i2s_alt0: i2s_alt0 {
@@ -34,3 +101,9 @@
&hdmi {
hpd-gpios = <&gpio 46 GPIO_ACTIVE_LOW>;
};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_gpio14>;
+ status = "okay";
+};
diff --git a/arch/arm/dts/bcm2835-rpi-b-rev2.dts b/arch/arm/dts/bcm2835-rpi-b-rev2.dts
index bfc4bd9..e860964 100644
--- a/arch/arm/dts/bcm2835-rpi-b-rev2.dts
+++ b/arch/arm/dts/bcm2835-rpi-b-rev2.dts
@@ -2,6 +2,7 @@
#include "bcm2835.dtsi"
#include "bcm2835-rpi.dtsi"
#include "bcm283x-rpi-smsc9512.dtsi"
+#include "bcm283x-rpi-usb-host.dtsi"
/ {
compatible = "raspberrypi,model-b-rev2", "brcm,bcm2835";
@@ -15,7 +16,73 @@
};
&gpio {
- pinctrl-0 = <&gpioout &alt0 &i2s_alt2 &alt3>;
+ /*
+ * Taken from Raspberry-Pi-Rev-2.0-Model-AB-Schematics.pdf
+ * RPI00022 sheet 02
+ *
+ * Legend:
+ * "NC" = not connected (no rail from the SoC)
+ * "FOO" = GPIO line named "FOO" on the schematic
+ * "FOO_N" = GPIO line named "FOO" on schematic, active low
+ */
+ gpio-line-names = "SDA0",
+ "SCL0",
+ "SDA1",
+ "SCL1",
+ "GPIO_GCLK",
+ "CAM_CLK",
+ "LAN_RUN",
+ "SPI_CE1_N",
+ "SPI_CE0_N",
+ "SPI_MISO",
+ "SPI_MOSI",
+ "SPI_SCLK",
+ "NC", /* GPIO12 */
+ "NC", /* GPIO13 */
+ /* Serial port */
+ "TXD0",
+ "RXD0",
+ "STATUS_LED_N",
+ "GPIO17",
+ "GPIO18",
+ "NC", /* GPIO19 */
+ "NC", /* GPIO20 */
+ "CAM_GPIO",
+ "GPIO22",
+ "GPIO23",
+ "GPIO24",
+ "GPIO25",
+ "NC", /* GPIO26 */
+ "GPIO27",
+ "GPIO28",
+ "GPIO29",
+ "GPIO30",
+ "GPIO31",
+ "NC", /* GPIO32 */
+ "NC", /* GPIO33 */
+ "NC", /* GPIO34 */
+ "NC", /* GPIO35 */
+ "NC", /* GPIO36 */
+ "NC", /* GPIO37 */
+ "NC", /* GPIO38 */
+ "NC", /* GPIO39 */
+ "PWM0_OUT",
+ "NC", /* GPIO41 */
+ "NC", /* GPIO42 */
+ "NC", /* GPIO43 */
+ "NC", /* GPIO44 */
+ "PWM1_OUT",
+ "HDMI_HPD_P",
+ "SD_CARD_DET",
+ /* Used by SD Card */
+ "SD_CLK_R",
+ "SD_CMD_R",
+ "SD_DATA0_R",
+ "SD_DATA1_R",
+ "SD_DATA2_R",
+ "SD_DATA3_R";
+
+ pinctrl-0 = <&gpioout &alt0 &i2s_alt2>;
/* I2S interface */
i2s_alt2: i2s_alt2 {
@@ -27,3 +94,9 @@
&hdmi {
hpd-gpios = <&gpio 46 GPIO_ACTIVE_LOW>;
};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_gpio14>;
+ status = "okay";
+};
diff --git a/arch/arm/dts/bcm2835-rpi-b.dts b/arch/arm/dts/bcm2835-rpi-b.dts
index 0371bb7..5d77f3f 100644
--- a/arch/arm/dts/bcm2835-rpi-b.dts
+++ b/arch/arm/dts/bcm2835-rpi-b.dts
@@ -2,6 +2,7 @@
#include "bcm2835.dtsi"
#include "bcm2835-rpi.dtsi"
#include "bcm283x-rpi-smsc9512.dtsi"
+#include "bcm283x-rpi-usb-host.dtsi"
/ {
compatible = "raspberrypi,model-b", "brcm,bcm2835";
@@ -15,9 +16,82 @@
};
&gpio {
- pinctrl-0 = <&gpioout &alt0 &alt3>;
+ /*
+ * Taken from Raspberry-Pi-Rev-1.0-Model-AB-Schematics.pdf
+ * RPI00021 sheet 02
+ *
+ * Legend:
+ * "NC" = not connected (no rail from the SoC)
+ * "FOO" = GPIO line named "FOO" on the schematic
+ * "FOO_N" = GPIO line named "FOO" on schematic, active low
+ */
+ gpio-line-names = "SDA0",
+ "SCL0",
+ "SDA1",
+ "SCL1",
+ "GPIO_GCLK",
+ "CAM_GPIO1",
+ "LAN_RUN",
+ "SPI_CE1_N",
+ "SPI_CE0_N",
+ "SPI_MISO",
+ "SPI_MOSI",
+ "SPI_SCLK",
+ "NC", /* GPIO12 */
+ "NC", /* GPIO13 */
+ /* Serial port */
+ "TXD0",
+ "RXD0",
+ "STATUS_LED_N",
+ "GPIO17",
+ "GPIO18",
+ "NC", /* GPIO19 */
+ "NC", /* GPIO20 */
+ "GPIO21",
+ "GPIO22",
+ "GPIO23",
+ "GPIO24",
+ "GPIO25",
+ "NC", /* GPIO26 */
+ "CAM_GPIO0",
+ /* Binary number representing build/revision */
+ "CONFIG0",
+ "CONFIG1",
+ "CONFIG2",
+ "CONFIG3",
+ "NC", /* GPIO32 */
+ "NC", /* GPIO33 */
+ "NC", /* GPIO34 */
+ "NC", /* GPIO35 */
+ "NC", /* GPIO36 */
+ "NC", /* GPIO37 */
+ "NC", /* GPIO38 */
+ "NC", /* GPIO39 */
+ "PWM0_OUT",
+ "NC", /* GPIO41 */
+ "NC", /* GPIO42 */
+ "NC", /* GPIO43 */
+ "NC", /* GPIO44 */
+ "PWM1_OUT",
+ "HDMI_HPD_P",
+ "SD_CARD_DET",
+ /* Used by SD Card */
+ "SD_CLK_R",
+ "SD_CMD_R",
+ "SD_DATA0_R",
+ "SD_DATA1_R",
+ "SD_DATA2_R",
+ "SD_DATA3_R";
+
+ pinctrl-0 = <&gpioout &alt0>;
};
&hdmi {
hpd-gpios = <&gpio 46 GPIO_ACTIVE_HIGH>;
};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_gpio14>;
+ status = "okay";
+};
diff --git a/arch/arm/dts/bcm2835-rpi.dtsi b/arch/arm/dts/bcm2835-rpi.dtsi
index e9b47b2..8b95832 100644
--- a/arch/arm/dts/bcm2835-rpi.dtsi
+++ b/arch/arm/dts/bcm2835-rpi.dtsi
@@ -39,22 +39,21 @@
};
alt0: alt0 {
- brcm,pins = <0 1 2 3 4 5 7 8 9 10 11 14 15 40 45>;
+ brcm,pins = <4 5 7 8 9 10 11>;
brcm,function = <BCM2835_FSEL_ALT0>;
};
-
- alt3: alt3 {
- brcm,pins = <48 49 50 51 52 53>;
- brcm,function = <BCM2835_FSEL_ALT3>;
- };
};
&i2c0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c0_gpio0>;
status = "okay";
clock-frequency = <100000>;
};
&i2c1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c1_gpio2>;
status = "okay";
clock-frequency = <100000>;
};
@@ -64,11 +63,21 @@
};
&sdhci {
+ pinctrl-names = "default";
+ pinctrl-0 = <&emmc_gpio48>;
status = "okay";
bus-width = <4>;
};
+&sdhost {
+ pinctrl-names = "default";
+ pinctrl-0 = <&sdhost_gpio48>;
+ bus-width = <4>;
+};
+
&pwm {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pwm0_gpio40 &pwm1_gpio45>;
status = "okay";
};
@@ -84,3 +93,16 @@
power-domains = <&power RPI_POWER_DOMAIN_HDMI>;
status = "okay";
};
+
+&vec {
+ power-domains = <&power RPI_POWER_DOMAIN_VEC>;
+ status = "okay";
+};
+
+&dsi0 {
+ power-domains = <&power RPI_POWER_DOMAIN_DSI0>;
+};
+
+&dsi1 {
+ power-domains = <&power RPI_POWER_DOMAIN_DSI1>;
+};
diff --git a/arch/arm/dts/bcm2835.dtsi b/arch/arm/dts/bcm2835.dtsi
index a78759e..659b6e9 100644
--- a/arch/arm/dts/bcm2835.dtsi
+++ b/arch/arm/dts/bcm2835.dtsi
@@ -23,3 +23,13 @@
};
};
};
+
+&cpu_thermal {
+ coefficients = <(-538) 407000>;
+};
+
+/* enable thermal sensor with the correct compatible property set */
+&thermal {
+ compatible = "brcm,bcm2835-thermal";
+ status = "okay";
+};
diff --git a/arch/arm/dts/bcm2836-rpi-2-b.dts b/arch/arm/dts/bcm2836-rpi-2-b.dts
index 29e1cfe..e8de414 100644
--- a/arch/arm/dts/bcm2836-rpi-2-b.dts
+++ b/arch/arm/dts/bcm2836-rpi-2-b.dts
@@ -2,6 +2,7 @@
#include "bcm2836.dtsi"
#include "bcm2835-rpi.dtsi"
#include "bcm283x-rpi-smsc9514.dtsi"
+#include "bcm283x-rpi-usb-host.dtsi"
/ {
compatible = "raspberrypi,2-model-b", "brcm,bcm2836";
@@ -26,7 +27,7 @@
};
&gpio {
- pinctrl-0 = <&gpioout &alt0 &i2s_alt0 &alt3>;
+ pinctrl-0 = <&gpioout &alt0 &i2s_alt0>;
/* I2S interface */
i2s_alt0: i2s_alt0 {
@@ -38,3 +39,9 @@
&hdmi {
hpd-gpios = <&gpio 46 GPIO_ACTIVE_LOW>;
};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_gpio14>;
+ status = "okay";
+};
diff --git a/arch/arm/dts/bcm2836.dtsi b/arch/arm/dts/bcm2836.dtsi
index 9d0651d..2c26d0b 100644
--- a/arch/arm/dts/bcm2836.dtsi
+++ b/arch/arm/dts/bcm2836.dtsi
@@ -36,6 +36,7 @@
cpus: cpus {
#address-cells = <1>;
#size-cells = <0>;
+ enable-method = "brcm,bcm2836-smp";
v7_cpu0: cpu@0 {
device_type = "cpu";
@@ -76,3 +77,13 @@
interrupt-parent = <&local_intc>;
interrupts = <8>;
};
+
+&cpu_thermal {
+ coefficients = <(-538) 407000>;
+};
+
+/* enable thermal sensor with the correct compatible property set */
+&thermal {
+ compatible = "brcm,bcm2836-thermal";
+ status = "okay";
+};
diff --git a/arch/arm/dts/bcm2837-rpi-3-b.dts b/arch/arm/dts/bcm2837-rpi-3-b.dts
index 7841b72..20725ca 100644
--- a/arch/arm/dts/bcm2837-rpi-3-b.dts
+++ b/arch/arm/dts/bcm2837-rpi-3-b.dts
@@ -2,6 +2,7 @@
#include "bcm2837.dtsi"
#include "bcm2835-rpi.dtsi"
#include "bcm283x-rpi-smsc9514.dtsi"
+#include "bcm283x-rpi-usb-host.dtsi"
/ {
compatible = "raspberrypi,3-model-b", "brcm,bcm2837";
@@ -15,16 +16,36 @@
act {
gpios = <&gpio 47 0>;
};
-
- pwr {
- label = "PWR";
- gpios = <&gpio 35 0>;
- default-state = "keep";
- linux,default-trigger = "default-on";
- };
};
};
-&uart1 {
+/* uart0 communicates with the BT module */
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_gpio32 &gpclk2_gpio43>;
status = "okay";
};
+
+/* uart1 is mapped to the pin header */
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart1_gpio14>;
+ status = "okay";
+};
+
+/* SDHCI is used to control the SDIO for wireless */
+&sdhci {
+ pinctrl-names = "default";
+ pinctrl-0 = <&emmc_gpio34>;
+ status = "okay";
+ bus-width = <4>;
+ non-removable;
+};
+
+/* SDHOST is used to drive the SD card */
+&sdhost {
+ pinctrl-names = "default";
+ pinctrl-0 = <&sdhost_gpio48>;
+ status = "okay";
+ bus-width = <4>;
+};
diff --git a/arch/arm/dts/bcm2837.dtsi b/arch/arm/dts/bcm2837.dtsi
index 8216bbb..bc1cca5 100644
--- a/arch/arm/dts/bcm2837.dtsi
+++ b/arch/arm/dts/bcm2837.dtsi
@@ -1,7 +1,7 @@
#include "bcm283x.dtsi"
/ {
- compatible = "brcm,bcm2836";
+ compatible = "brcm,bcm2837";
soc {
ranges = <0x7e000000 0x3f000000 0x1000000>,
@@ -30,6 +30,7 @@
cpus: cpus {
#address-cells = <1>;
#size-cells = <0>;
+ enable-method = "brcm,bcm2836-smp"; // for ARM 32-bit
cpu0: cpu@0 {
device_type = "cpu";
@@ -74,3 +75,13 @@
interrupt-parent = <&local_intc>;
interrupts = <8>;
};
+
+&cpu_thermal {
+ coefficients = <(-538) 412000>;
+};
+
+/* enable thermal sensor with the correct compatible property set */
+&thermal {
+ compatible = "brcm,bcm2837-thermal";
+ status = "okay";
+};
diff --git a/arch/arm/dts/bcm283x-rpi-smsc9512.dtsi b/arch/arm/dts/bcm283x-rpi-smsc9512.dtsi
index 12c981e..9a0599f 100644
--- a/arch/arm/dts/bcm283x-rpi-smsc9512.dtsi
+++ b/arch/arm/dts/bcm283x-rpi-smsc9512.dtsi
@@ -1,6 +1,6 @@
/ {
aliases {
- ethernet = ðernet;
+ ethernet0 = ðernet;
};
};
diff --git a/arch/arm/dts/bcm283x-rpi-smsc9514.dtsi b/arch/arm/dts/bcm283x-rpi-smsc9514.dtsi
index 3f0a56e..dc7ae77 100644
--- a/arch/arm/dts/bcm283x-rpi-smsc9514.dtsi
+++ b/arch/arm/dts/bcm283x-rpi-smsc9514.dtsi
@@ -1,6 +1,6 @@
/ {
aliases {
- ethernet = ðernet;
+ ethernet0 = ðernet;
};
};
diff --git a/arch/arm/dts/bcm283x-rpi-usb-host.dtsi b/arch/arm/dts/bcm283x-rpi-usb-host.dtsi
new file mode 100644
index 0000000..73f4ece
--- /dev/null
+++ b/arch/arm/dts/bcm283x-rpi-usb-host.dtsi
@@ -0,0 +1,3 @@
+&usb {
+ dr_mode = "host";
+};
diff --git a/arch/arm/dts/bcm283x.dtsi b/arch/arm/dts/bcm283x.dtsi
index e5b4f20..05a6f48 100644
--- a/arch/arm/dts/bcm283x.dtsi
+++ b/arch/arm/dts/bcm283x.dtsi
@@ -3,6 +3,11 @@
#include <dt-bindings/clock/bcm2835-aux.h>
#include <dt-bindings/gpio/gpio.h>
+/* firmware-provided startup stubs live here, where the secondary CPUs are
+ * spinning.
+ */
+/memreserve/ 0x00000000 0x00001000;
+
/* This include file covers the common peripherals and configuration between
* bcm2835 and bcm2836 implementations, leaving the CPU configuration to
* bcm2835.dtsi and bcm2836.dtsi.
@@ -19,6 +24,26 @@
bootargs = "earlyprintk console=ttyAMA0";
};
+ thermal-zones {
+ cpu_thermal: cpu-thermal {
+ polling-delay-passive = <0>;
+ polling-delay = <1000>;
+
+ thermal-sensors = <&thermal>;
+
+ trips {
+ cpu-crit {
+ temperature = <80000>;
+ hysteresis = <0>;
+ type = "critical";
+ };
+ };
+
+ cooling-maps {
+ };
+ };
+ };
+
soc: soc {
compatible = "simple-bus";
#address-cells = <1>;
@@ -93,10 +118,13 @@
#clock-cells = <1>;
reg = <0x7e101000 0x2000>;
- /* CPRMAN derives everything from the platform's
- * oscillator.
+ /* CPRMAN derives almost everything from the
+ * platform's oscillator. However, the DSI
+ * pixel clocks come from the DSI analog PHY.
*/
- clocks = <&clk_osc>;
+ clocks = <&clk_osc>,
+ <&dsi0 0>, <&dsi0 1>, <&dsi0 2>,
+ <&dsi1 0>, <&dsi1 1>, <&dsi1 2>;
};
rng@7e104000 {
@@ -104,7 +132,7 @@
reg = <0x7e104000 0x10>;
};
- mailbox: mailbox@7e00b800 {
+ mailbox: mailbox@7e00b880 {
compatible = "brcm,bcm2835-mbox";
reg = <0x7e00b880 0x40>;
interrupts = <0 1>;
@@ -132,6 +160,213 @@
interrupt-controller;
#interrupt-cells = <2>;
+
+ /* Defines pin muxing groups according to
+ * BCM2835-ARM-Peripherals.pdf page 102.
+ *
+ * While each pin can have its mux selected
+ * for various functions individually, some
+ * groups only make sense to switch to a
+ * particular function together.
+ */
+ dpi_gpio0: dpi_gpio0 {
+ brcm,pins = <0 1 2 3 4 5 6 7 8 9 10 11
+ 12 13 14 15 16 17 18 19
+ 20 21 22 23 24 25 26 27>;
+ brcm,function = <BCM2835_FSEL_ALT2>;
+ };
+ emmc_gpio22: emmc_gpio22 {
+ brcm,pins = <22 23 24 25 26 27>;
+ brcm,function = <BCM2835_FSEL_ALT3>;
+ };
+ emmc_gpio34: emmc_gpio34 {
+ brcm,pins = <34 35 36 37 38 39>;
+ brcm,function = <BCM2835_FSEL_ALT3>;
+ brcm,pull = <BCM2835_PUD_OFF
+ BCM2835_PUD_UP
+ BCM2835_PUD_UP
+ BCM2835_PUD_UP
+ BCM2835_PUD_UP
+ BCM2835_PUD_UP>;
+ };
+ emmc_gpio48: emmc_gpio48 {
+ brcm,pins = <48 49 50 51 52 53>;
+ brcm,function = <BCM2835_FSEL_ALT3>;
+ };
+
+ gpclk0_gpio4: gpclk0_gpio4 {
+ brcm,pins = <4>;
+ brcm,function = <BCM2835_FSEL_ALT0>;
+ };
+ gpclk1_gpio5: gpclk1_gpio5 {
+ brcm,pins = <5>;
+ brcm,function = <BCM2835_FSEL_ALT0>;
+ };
+ gpclk1_gpio42: gpclk1_gpio42 {
+ brcm,pins = <42>;
+ brcm,function = <BCM2835_FSEL_ALT0>;
+ };
+ gpclk1_gpio44: gpclk1_gpio44 {
+ brcm,pins = <44>;
+ brcm,function = <BCM2835_FSEL_ALT0>;
+ };
+ gpclk2_gpio6: gpclk2_gpio6 {
+ brcm,pins = <6>;
+ brcm,function = <BCM2835_FSEL_ALT0>;
+ };
+ gpclk2_gpio43: gpclk2_gpio43 {
+ brcm,pins = <43>;
+ brcm,function = <BCM2835_FSEL_ALT0>;
+ };
+
+ i2c0_gpio0: i2c0_gpio0 {
+ brcm,pins = <0 1>;
+ brcm,function = <BCM2835_FSEL_ALT0>;
+ };
+ i2c0_gpio28: i2c0_gpio28 {
+ brcm,pins = <28 29>;
+ brcm,function = <BCM2835_FSEL_ALT0>;
+ };
+ i2c0_gpio44: i2c0_gpio44 {
+ brcm,pins = <44 45>;
+ brcm,function = <BCM2835_FSEL_ALT1>;
+ };
+ i2c1_gpio2: i2c1_gpio2 {
+ brcm,pins = <2 3>;
+ brcm,function = <BCM2835_FSEL_ALT0>;
+ };
+ i2c1_gpio44: i2c1_gpio44 {
+ brcm,pins = <44 45>;
+ brcm,function = <BCM2835_FSEL_ALT2>;
+ };
+ i2c_slave_gpio18: i2c_slave_gpio18 {
+ brcm,pins = <18 19 20 21>;
+ brcm,function = <BCM2835_FSEL_ALT3>;
+ };
+
+ jtag_gpio4: jtag_gpio4 {
+ brcm,pins = <4 5 6 12 13>;
+ brcm,function = <BCM2835_FSEL_ALT4>;
+ };
+ jtag_gpio22: jtag_gpio22 {
+ brcm,pins = <22 23 24 25 26 27>;
+ brcm,function = <BCM2835_FSEL_ALT4>;
+ };
+
+ pcm_gpio18: pcm_gpio18 {
+ brcm,pins = <18 19 20 21>;
+ brcm,function = <BCM2835_FSEL_ALT0>;
+ };
+ pcm_gpio28: pcm_gpio28 {
+ brcm,pins = <28 29 30 31>;
+ brcm,function = <BCM2835_FSEL_ALT2>;
+ };
+
+ pwm0_gpio12: pwm0_gpio12 {
+ brcm,pins = <12>;
+ brcm,function = <BCM2835_FSEL_ALT0>;
+ };
+ pwm0_gpio18: pwm0_gpio18 {
+ brcm,pins = <18>;
+ brcm,function = <BCM2835_FSEL_ALT5>;
+ };
+ pwm0_gpio40: pwm0_gpio40 {
+ brcm,pins = <40>;
+ brcm,function = <BCM2835_FSEL_ALT0>;
+ };
+ pwm1_gpio13: pwm1_gpio13 {
+ brcm,pins = <13>;
+ brcm,function = <BCM2835_FSEL_ALT0>;
+ };
+ pwm1_gpio19: pwm1_gpio19 {
+ brcm,pins = <19>;
+ brcm,function = <BCM2835_FSEL_ALT5>;
+ };
+ pwm1_gpio41: pwm1_gpio41 {
+ brcm,pins = <41>;
+ brcm,function = <BCM2835_FSEL_ALT0>;
+ };
+ pwm1_gpio45: pwm1_gpio45 {
+ brcm,pins = <45>;
+ brcm,function = <BCM2835_FSEL_ALT0>;
+ };
+
+ sdhost_gpio48: sdhost_gpio48 {
+ brcm,pins = <48 49 50 51 52 53>;
+ brcm,function = <BCM2835_FSEL_ALT0>;
+ };
+
+ spi0_gpio7: spi0_gpio7 {
+ brcm,pins = <7 8 9 10 11>;
+ brcm,function = <BCM2835_FSEL_ALT0>;
+ };
+ spi0_gpio35: spi0_gpio35 {
+ brcm,pins = <35 36 37 38 39>;
+ brcm,function = <BCM2835_FSEL_ALT0>;
+ };
+ spi1_gpio16: spi1_gpio16 {
+ brcm,pins = <16 17 18 19 20 21>;
+ brcm,function = <BCM2835_FSEL_ALT4>;
+ };
+ spi2_gpio40: spi2_gpio40 {
+ brcm,pins = <40 41 42 43 44 45>;
+ brcm,function = <BCM2835_FSEL_ALT4>;
+ };
+
+ uart0_gpio14: uart0_gpio14 {
+ brcm,pins = <14 15>;
+ brcm,function = <BCM2835_FSEL_ALT0>;
+ };
+ /* Separate from the uart0_gpio14 group
+ * because it conflicts with spi1_gpio16, and
+ * people often run uart0 on the two pins
+ * without flow control.
+ */
+ uart0_ctsrts_gpio16: uart0_ctsrts_gpio16 {
+ brcm,pins = <16 17>;
+ brcm,function = <BCM2835_FSEL_ALT3>;
+ };
+ uart0_ctsrts_gpio30: uart0_ctsrts_gpio30 {
+ brcm,pins = <30 31>;
+ brcm,function = <BCM2835_FSEL_ALT3>;
+ };
+ uart0_gpio32: uart0_gpio32 {
+ brcm,pins = <32 33>;
+ brcm,function = <BCM2835_FSEL_ALT3>;
+ };
+ uart0_gpio36: uart0_gpio36 {
+ brcm,pins = <36 37>;
+ brcm,function = <BCM2835_FSEL_ALT2>;
+ };
+ uart0_ctsrts_gpio38: uart0_ctsrts_gpio38 {
+ brcm,pins = <38 39>;
+ brcm,function = <BCM2835_FSEL_ALT2>;
+ };
+
+ uart1_gpio14: uart1_gpio14 {
+ brcm,pins = <14 15>;
+ brcm,function = <BCM2835_FSEL_ALT5>;
+ };
+ uart1_ctsrts_gpio16: uart1_ctsrts_gpio16 {
+ brcm,pins = <16 17>;
+ brcm,function = <BCM2835_FSEL_ALT5>;
+ };
+ uart1_gpio32: uart1_gpio32 {
+ brcm,pins = <32 33>;
+ brcm,function = <BCM2835_FSEL_ALT5>;
+ };
+ uart1_ctsrts_gpio30: uart1_ctsrts_gpio30 {
+ brcm,pins = <30 31>;
+ brcm,function = <BCM2835_FSEL_ALT5>;
+ };
+ uart1_gpio40: uart1_gpio40 {
+ brcm,pins = <40 41>;
+ brcm,function = <BCM2835_FSEL_ALT5>;
+ };
+ uart1_ctsrts_gpio42: uart1_ctsrts_gpio42 {
+ brcm,pins = <42 43>;
+ brcm,function = <BCM2835_FSEL_ALT5>;
+ };
};
uart0: serial@7e201000 {
@@ -144,6 +379,16 @@
arm,primecell-periphid = <0x00241011>;
};
+ sdhost: mmc@7e202000 {
+ compatible = "brcm,bcm2835-sdhost";
+ reg = <0x7e202000 0x100>;
+ interrupts = <2 24>;
+ clocks = <&clocks BCM2835_CLOCK_VPU>;
+ dmas = <&dma 13>;
+ dma-names = "rx-tx";
+ status = "disabled";
+ };
+
i2s: i2s@7e203000 {
compatible = "brcm,bcm2835-i2s";
reg = <0x7e203000 0x20>,
@@ -187,6 +432,33 @@
interrupts = <2 14>; /* pwa1 */
};
+ dsi0: dsi@7e209000 {
+ compatible = "brcm,bcm2835-dsi0";
+ reg = <0x7e209000 0x78>;
+ interrupts = <2 4>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ #clock-cells = <1>;
+
+ clocks = <&clocks BCM2835_PLLA_DSI0>,
+ <&clocks BCM2835_CLOCK_DSI0E>,
+ <&clocks BCM2835_CLOCK_DSI0P>;
+ clock-names = "phy", "escape", "pixel";
+
+ clock-output-names = "dsi0_byte",
+ "dsi0_ddr2",
+ "dsi0_ddr";
+
+ };
+
+ thermal: thermal@7e212000 {
+ compatible = "brcm,bcm2835-thermal";
+ reg = <0x7e212000 0x8>;
+ clocks = <&clocks BCM2835_CLOCK_TSENS>;
+ #thermal-sensor-cells = <0>;
+ status = "disabled";
+ };
+
aux: aux@0x7e215000 {
compatible = "brcm,bcm2835-aux";
#clock-cells = <1>;
@@ -246,6 +518,26 @@
interrupts = <2 1>;
};
+ dsi1: dsi@7e700000 {
+ compatible = "brcm,bcm2835-dsi1";
+ reg = <0x7e700000 0x8c>;
+ interrupts = <2 12>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ #clock-cells = <1>;
+
+ clocks = <&clocks BCM2835_PLLD_DSI1>,
+ <&clocks BCM2835_CLOCK_DSI1E>,
+ <&clocks BCM2835_CLOCK_DSI1P>;
+ clock-names = "phy", "escape", "pixel";
+
+ clock-output-names = "dsi1_byte",
+ "dsi1_ddr2",
+ "dsi1_ddr";
+
+ status = "disabled";
+ };
+
i2c1: i2c@7e804000 {
compatible = "brcm,bcm2835-i2c";
reg = <0x7e804000 0x1000>;
@@ -266,6 +558,14 @@
status = "disabled";
};
+ vec: vec@7e806000 {
+ compatible = "brcm,bcm2835-vec";
+ reg = <0x7e806000 0x1000>;
+ clocks = <&clocks BCM2835_CLOCK_VEC>;
+ interrupts = <2 27>;
+ status = "disabled";
+ };
+
pixelvalve@7e807000 {
compatible = "brcm,bcm2835-pixelvalve2";
reg = <0x7e807000 0x100>;
@@ -281,6 +581,8 @@
clocks = <&clocks BCM2835_PLLH_PIX>,
<&clocks BCM2835_CLOCK_HSM>;
clock-names = "pixel", "hdmi";
+ dmas = <&dma 17>;
+ dma-names = "audio-rx";
status = "disabled";
};
@@ -290,6 +592,10 @@
interrupts = <1 9>;
#address-cells = <1>;
#size-cells = <0>;
+ clocks = <&clk_usb>;
+ clock-names = "otg";
+ phys = <&usbphy>;
+ phy-names = "usb2-phy";
};
v3d: v3d@7ec00000 {
@@ -317,6 +623,17 @@
clock-frequency = <19200000>;
};
+ clk_usb: clock@4 {
+ compatible = "fixed-clock";
+ reg = <4>;
+ #clock-cells = <0>;
+ clock-output-names = "otg";
+ clock-frequency = <480000000>;
+ };
+ };
+
+ usbphy: phy {
+ compatible = "usb-nop-xceiv";
};
};