eNET: Define MMCR values in config.h
diff --git a/board/eNET/eNET.c b/board/eNET/eNET.c
index 3b74ce9..546406a 100644
--- a/board/eNET/eNET.c
+++ b/board/eNET/eNET.c
@@ -53,36 +53,57 @@
*/
int board_early_init_f(void)
{
- writeb(0x01, &sc520_mmcr->gpcsrt); /* GP Chip Select Recovery Time */
- writeb(0x07, &sc520_mmcr->gpcspw); /* GP Chip Select Pulse Width */
- writeb(0x00, &sc520_mmcr->gpcsoff); /* GP Chip Select Offset */
- writeb(0x05, &sc520_mmcr->gprdw); /* GP Read pulse width */
- writeb(0x01, &sc520_mmcr->gprdoff); /* GP Read offset */
- writeb(0x05, &sc520_mmcr->gpwrw); /* GP Write pulse width */
- writeb(0x01, &sc520_mmcr->gpwroff); /* GP Write offset */
+ u16 pio_out_cfg = 0x0000;
- writew(0x0630, &sc520_mmcr->piodata15_0); /* PIO15_PIO0 Data */
- writew(0x2000, &sc520_mmcr->piodata31_16); /* PIO31_PIO16 Data */
- writew(0x2000, &sc520_mmcr->piodir31_16); /* GPIO Direction */
- writew(0x87b5, &sc520_mmcr->piodir15_0); /* GPIO Direction */
- writew(0x0dfe, &sc520_mmcr->piopfs31_16); /* GPIO pin function 31-16 reg */
- writew(0x200a, &sc520_mmcr->piopfs15_0); /* GPIO pin function 15-0 reg */
- writeb(0xf8, &sc520_mmcr->cspfs); /* Chip Select Pin Function Select */
+ /* Configure General Purpose Bus timing */
+ writeb(CONFIG_SYS_SC520_GPCSRT, &sc520_mmcr->gpcsrt);
+ writeb(CONFIG_SYS_SC520_GPCSPW, &sc520_mmcr->gpcspw);
+ writeb(CONFIG_SYS_SC520_GPCSOFF, &sc520_mmcr->gpcsoff);
+ writeb(CONFIG_SYS_SC520_GPRDW, &sc520_mmcr->gprdw);
+ writeb(CONFIG_SYS_SC520_GPRDOFF, &sc520_mmcr->gprdoff);
+ writeb(CONFIG_SYS_SC520_GPWRW, &sc520_mmcr->gpwrw);
+ writeb(CONFIG_SYS_SC520_GPWROFF, &sc520_mmcr->gpwroff);
- writel(0x200713f8, &sc520_mmcr->par[2]); /* Uart A (GPCS0, 0x013f8, 8 Bytes) */
- writel(0x2c0712f8, &sc520_mmcr->par[3]); /* Uart B (GPCS3, 0x012f8, 8 Bytes) */
- writel(0x300711f8, &sc520_mmcr->par[4]); /* Uart C (GPCS4, 0x011f8, 8 Bytes) */
- writel(0x340710f8, &sc520_mmcr->par[5]); /* Uart D (GPCS5, 0x010f8, 8 Bytes) */
- writel(0xe3ffc000, &sc520_mmcr->par[6]); /* SDRAM (0x00000000, 128MB) */
- writel(0xaa3fd000, &sc520_mmcr->par[7]); /* StrataFlash (ROMCS1, 0x10000000, 16MB) */
- writel(0xca3fd100, &sc520_mmcr->par[8]); /* StrataFlash (ROMCS2, 0x11000000, 16MB) */
- writel(0x4203d900, &sc520_mmcr->par[9]); /* SRAM (GPCS0, 0x19000000, 1MB) */
- writel(0x4e03d910, &sc520_mmcr->par[10]); /* SRAM (GPCS3, 0x19100000, 1MB) */
- writel(0x50018100, &sc520_mmcr->par[11]); /* DP-RAM (GPCS4, 0x18100000, 4kB) */
- writel(0x54020000, &sc520_mmcr->par[12]); /* CFLASH1 (0x200000000, 4kB) */
- writel(0x5c020001, &sc520_mmcr->par[13]); /* CFLASH2 (0x200010000, 4kB) */
-/* writel(0x8bfff800, &sc520_mmcr->par14); */ /* BOOTCS at 0x18000000 */
-/* writel(0x38201000, &sc520_mmcr->par15); */ /* LEDs etc (GPCS6, 0x1000, 20 Bytes */
+ /* Configure Programmable Input/Output Pins */
+ writew(CONFIG_SYS_SC520_PIODIR15_0, &sc520_mmcr->piodir15_0);
+ writew(CONFIG_SYS_SC520_PIODIR31_16, &sc520_mmcr->piodir31_16);
+ writew(CONFIG_SYS_SC520_PIOPFS31_16, &sc520_mmcr->piopfs31_16);
+ writew(CONFIG_SYS_SC520_PIOPFS15_0, &sc520_mmcr->piopfs15_0);
+ writeb(CONFIG_SYS_SC520_CSPFS, &sc520_mmcr->cspfs);
+ writeb(CONFIG_SYS_SC520_CLKSEL, &sc520_mmcr->clksel);
+
+ /*
+ * Turn off top board
+ * Set StrataFlash chips to 16-bit width
+ * Set StrataFlash chips to normal (non reset/power down) mode
+ */
+ pio_out_cfg |= CONFIG_SYS_ENET_TOP_BRD_PWR;
+ pio_out_cfg |= CONFIG_SYS_ENET_SF_WIDTH;
+ pio_out_cfg |= CONFIG_SYS_ENET_SF1_MODE;
+ pio_out_cfg |= CONFIG_SYS_ENET_SF2_MODE;
+ writew(pio_out_cfg, &sc520_mmcr->pioset15_0);
+
+ /* Turn off auxiliary power output */
+ writew(CONFIG_SYS_ENET_AUX_PWR, &sc520_mmcr->pioclr15_0);
+
+ /* Clear FPGA program mode */
+ writew(CONFIG_SYS_ENET_FPGA_PROG, &sc520_mmcr->pioset31_16);
+
+ /* Configure Programmable Address Regions */
+ writel(CONFIG_SYS_SC520_UARTA_PAR, &sc520_mmcr->par[2]);
+ writel(CONFIG_SYS_SC520_UARTB_PAR, &sc520_mmcr->par[3]);
+ writel(CONFIG_SYS_SC520_UARTC_PAR, &sc520_mmcr->par[4]);
+ writel(CONFIG_SYS_SC520_UARTD_PAR, &sc520_mmcr->par[5]);
+ writel(CONFIG_SYS_SC520_SDRAM_PAR, &sc520_mmcr->par[6]);
+ writel(CONFIG_SYS_SC520_SF1_PAR, &sc520_mmcr->par[7]);
+ writel(CONFIG_SYS_SC520_SF2_PAR, &sc520_mmcr->par[8]);
+ writel(CONFIG_SYS_SC520_SRAM1_PAR, &sc520_mmcr->par[9]);
+ writel(CONFIG_SYS_SC520_SRAM2_PAR, &sc520_mmcr->par[10]);
+ writel(CONFIG_SYS_SC520_DPRAM_PAR, &sc520_mmcr->par[11]);
+ writel(CONFIG_SYS_SC520_CF1_PAR, &sc520_mmcr->par[12]);
+ writel(CONFIG_SYS_SC520_CF2_PAR, &sc520_mmcr->par[13]);
+/* writel(CONFIG_SYS_SC520_BOOTCS_PAR, &sc520_mmcr->par14); */
+/* writel(CONFIG_SYS_SC520_LLIO_PAR, &sc520_mmcr->par15); */
/* Disable Watchdog */
writew(0x3333, &sc520_mmcr->wdtmrctl);
@@ -90,24 +111,19 @@
writew(0x0000, &sc520_mmcr->wdtmrctl);
/* Chip Select Configuration */
- writew(0x0033, &sc520_mmcr->bootcsctl);
- writew(0x0615, &sc520_mmcr->romcs1ctl);
- writew(0x0615, &sc520_mmcr->romcs2ctl);
+ writew(CONFIG_SYS_SC520_BOOTCS_CTRL, &sc520_mmcr->bootcsctl);
+ writew(CONFIG_SYS_SC520_ROMCS1_CTRL, &sc520_mmcr->romcs1ctl);
+ writew(CONFIG_SYS_SC520_ROMCS2_CTRL, &sc520_mmcr->romcs2ctl);
- /*
- * Set the timer pin mapping
- * no clock frequency selected, use 1.1892MHz
- */
- writeb(0x72, &sc520_mmcr->clksel);
+ writeb(CONFIG_SYS_SC520_ADDDECCTL, &sc520_mmcr->adddecctl);
+ writeb(CONFIG_SYS_SC520_UART1CTL, &sc520_mmcr->uart1ctl);
+ writeb(CONFIG_SYS_SC520_UART2CTL, &sc520_mmcr->uart2ctl);
- writeb(0x00, &sc520_mmcr->adddecctl);
- writeb(0x07, &sc520_mmcr->uart1ctl);
- writeb(0x07, &sc520_mmcr->uart2ctl);
- writeb(0x06, &sc520_mmcr->sysarbctl);
- writew(0x0003, &sc520_mmcr->sysarbmenb);
+ writeb(CONFIG_SYS_SC520_SYSARBCTL, &sc520_mmcr->sysarbctl);
+ writew(CONFIG_SYS_SC520_SYSARBMENB, &sc520_mmcr->sysarbmenb);
/* enable posted-writes */
- writeb(0x04, &sc520_mmcr->hbctl);
+ writeb(CONFIG_SYS_SC520_HBCTL, &sc520_mmcr->hbctl);
return 0;
}
diff --git a/board/eNET/eNET_start16.S b/board/eNET/eNET_start16.S
index 183309c..4835936 100644
--- a/board/eNET/eNET_start16.S
+++ b/board/eNET/eNET_start16.S
@@ -29,6 +29,7 @@
/* #include <asm/ic/sc520_defs.h> */
+#include "config.h"
#include "hardware.h"
#include <asm/ic/sc520.h>
@@ -48,12 +49,12 @@
/* Map PAR for Boot Flash (BOOTCS, 512kB @ 0x380000000) */
movl $(SC520_PAR14 - SC520_MMCR_BASE), %edi
- movl $0x8bfff800, %eax /* TODO: Check this */
+ movl $CONFIG_SYS_SC520_BOOTCS_PAR, %eax
movl %eax, (%di)
/* Map PAR for LED, Hex Switches (GPCS6, 20 Bytes @ 0x1000) */
movl $(SC520_PAR15 - SC520_MMCR_BASE), %edi
- movl $0x38201000, %eax
+ movl $CONFIG_SYS_SC520_LLIO_PAR, %eax
movl %eax, (%di)
/* Disable SDRAM write buffer */