Blackfin: easylogo: add lzma logos
The bf527-ezkit boards are getting too big to fit into their reserved
flash space, so we need to use a lzma compressed logo.
Since the video driver code is very similar, add lzma compressed support
to all of the Blackfin video drivers.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
diff --git a/board/bf527-ezkit/video.c b/board/bf527-ezkit/video.c
index ca5e9b0..5d8a091 100644
--- a/board/bf527-ezkit/video.c
+++ b/board/bf527-ezkit/video.c
@@ -17,6 +17,10 @@
#include <linux/types.h>
#include <stdio_dev.h>
+#include <lzma/LzmaTypes.h>
+#include <lzma/LzmaDec.h>
+#include <lzma/LzmaTools.h>
+
#include <asm/mach-common/bits/ppi.h>
#include <asm/mach-common/bits/timer.h>
@@ -24,12 +28,9 @@
#define LCD_Y_RES 240 /* Vertical Resolution */
#define DMA_BUS_SIZE 16
-#ifdef CONFIG_BF527_EZKIT_REV_2_1 /* lq035q1 */
+#include EASYLOGO_HEADER
-#if !defined(CONFIG_LQ035Q1_USE_RGB888_8_BIT_PPI) && \
- !defined(CONFIG_LQ035Q1_USE_RGB565_8_BIT_PPI)
-# define CONFIG_LQ035Q1_USE_RGB565_8_BIT_PPI
-#endif
+#ifdef CONFIG_BF527_EZKIT_REV_2_1 /* lq035q1 */
/* Interface 16/18-bit TFT over an 8-bit wide PPI using a
* small Programmable Logic Device (CPLD)
@@ -37,14 +38,12 @@
*/
#ifdef CONFIG_LQ035Q1_USE_RGB565_8_BIT_PPI
-#include <asm/bfin_logo_rgb565_230x230.h>
#define LCD_BPP 16 /* Bit Per Pixel */
#define CLOCKS_PPIX 2 /* Clocks per pixel */
#define CPLD_DELAY 3 /* RGB565 pipeline delay */
#endif
#ifdef CONFIG_LQ035Q1_USE_RGB888_8_BIT_PPI
-#include <asm/bfin_logo_230x230.h>
#define LCD_BPP 24 /* Bit Per Pixel */
#define CLOCKS_PPIX 3 /* Clocks per pixel */
#define CPLD_DELAY 5 /* RGB888 pipeline delay */
@@ -96,7 +95,6 @@
#endif
#else /* t350mcqb */
-#include <asm/bfin_logo_230x230.h>
#define LCD_BPP 24 /* Bit Per Pixel */
#define CLOCKS_PPIX 3 /* Clocks per pixel */
@@ -419,13 +417,23 @@
#ifdef EASYLOGO_ENABLE_GZIP
unsigned char *data = EASYLOGO_DECOMP_BUFFER;
unsigned long src_len = EASYLOGO_ENABLE_GZIP;
- if (gunzip(data, bfin_logo.size, bfin_logo.data, &src_len)) {
+ error = gunzip(data, bfin_logo.size, bfin_logo.data, &src_len);
+ bfin_logo.data = data;
+#elif defined(EASYLOGO_ENABLE_LZMA)
+ unsigned char *data = EASYLOGO_DECOMP_BUFFER;
+ SizeT lzma_len = bfin_logo.size;
+ error = lzmaBuffToBuffDecompress(data, &lzma_len,
+ bfin_logo.data, EASYLOGO_ENABLE_LZMA);
+ bfin_logo.data = data;
+#else
+ error = 0;
+#endif
+
+ if (error) {
puts("Failed to decompress logo\n");
free(dst);
return -1;
}
- bfin_logo.data = data;
-#endif
memset(dst + ACTIVE_VIDEO_MEM_OFFSET, bfin_logo.data[0], fbmem_size - ACTIVE_VIDEO_MEM_OFFSET);