* Patch by Robert Schwebel, 21 Jan 2003:
- Add support for Innokom board
- Don't complain if "install" fails
- README cleanup (remove duplicated lines)
- Update PXA header files
* Add documentation for existing POST code (doc/README.POST)
* Patch by Laudney Ren, 15 Jan 2003:
Fix handling of redundand environment in "tools/envcrc.c"
* Patch by Detlev Zundel, 28 Feb 2003:
Add bedbug support for 824x systems
* Add support for 16 MB flash configuration of TRAB board
* Patch by Erwin Rol, 27 Feb 2003:
Add support for RTEMS
* Add image information to README
* Fix dual PCMCIA slot support (when running with just one
slot populated)
* Add VFD type detection to trab board
* extend drivers/cs8900.c driver to synchronize ethaddr environment
variable with value in the EEPROM
diff --git a/include/asm-arm/arch-pxa/pxa-regs.h b/include/asm-arm/arch-pxa/pxa-regs.h
index 2975fa3..dda2465 100644
--- a/include/asm-arm/arch-pxa/pxa-regs.h
+++ b/include/asm-arm/arch-pxa/pxa-regs.h
@@ -10,6 +10,8 @@
* published by the Free Software Foundation.
*/
+#ifndef PXA_REGS_H
+#define PXA_REGS_H 1
/* FIXME hack so that SA-1111.h will work [cb] */
@@ -425,6 +427,38 @@
#define ISR __REG(0x40301698) /* I2C Status Register - ISR */
#define ISAR __REG(0x403016A0) /* I2C Slave Address Register - ISAR */
+/* ----- Control register bits ---------------------------------------- */
+
+#define ICR_START 0x1 /* start bit */
+#define ICR_STOP 0x2 /* stop bit */
+#define ICR_ACKNAK 0x4 /* send ACK(0) or NAK(1) */
+#define ICR_TB 0x8 /* transfer byte bit */
+#define ICR_MA 0x10 /* master abort */
+#define ICR_SCLE 0x20 /* master clock enable */
+#define ICR_IUE 0x40 /* unit enable */
+#define ICR_GCD 0x80 /* general call disable */
+#define ICR_ITEIE 0x100 /* enable tx interrupts */
+#define ICR_IRFIE 0x200 /* enable rx interrupts */
+#define ICR_BEIE 0x400 /* enable bus error ints */
+#define ICR_SSDIE 0x800 /* slave STOP detected int enable */
+#define ICR_ALDIE 0x1000 /* enable arbitration interrupt */
+#define ICR_SADIE 0x2000 /* slave address detected int enable */
+#define ICR_UR 0x4000 /* unit reset */
+
+/* ----- Status register bits ----------------------------------------- */
+
+#define ISR_RWM 0x1 /* read/write mode */
+#define ISR_ACKNAK 0x2 /* ack/nak status */
+#define ISR_UB 0x4 /* unit busy */
+#define ISR_IBB 0x8 /* bus busy */
+#define ISR_SSD 0x10 /* slave stop detected */
+#define ISR_ALD 0x20 /* arbitration loss detected */
+#define ISR_ITE 0x40 /* tx buffer empty */
+#define ISR_IRF 0x80 /* rx buffer full */
+#define ISR_GCAD 0x100 /* general call address detected */
+#define ISR_SAD 0x200 /* slave address detected */
+#define ISR_BED 0x400 /* bus error no ACK/NAK */
+
/*
* Serial Audio Controller
@@ -1128,6 +1162,6 @@
#define MCIO1_OFFSET 0x3C
#define MDMRS_OFFSET 0x40
-
+#endif /* PXA_REGS_H */
diff --git a/include/asm-arm/arch-xscale/pxa-regs.h b/include/asm-arm/arch-xscale/pxa-regs.h
index 2975fa3..449ec9f 100644
--- a/include/asm-arm/arch-xscale/pxa-regs.h
+++ b/include/asm-arm/arch-xscale/pxa-regs.h
@@ -1,15 +1,23 @@
/*
* linux/include/asm-arm/arch-pxa/pxa-regs.h
- *
+ *
* Author: Nicolas Pitre
* Created: Jun 15, 2001
* Copyright: MontaVista Software Inc.
- *
+ *
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
+ *
+ * - 2003/01/20: Robert Schwebel <r.schwebel@pengutronix.de
+ * Original file taken from linux-2.4.19-rmk4-pxa1. Added some definitions.
+ * Added include for hardware.h (for __REG definition)
*/
+#ifndef _PXA_REGS_H_
+#define _PXA_REGS_H_
+#include "bitfield.h"
+#include "hardware.h"
/* FIXME hack so that SA-1111.h will work [cb] */
@@ -22,13 +30,6 @@
typedef void (*ExcpHndlr) (void) ;
#endif
-#ifndef __ASSEMBLY__
-#define io_p2v(PhAdd) (PhAdd)
-#define __REG(x) (*((volatile u32 *)io_p2v(x)))
-#else
-#define __REG(x) (x)
-#endif
-
/*
* PXA Chip selects
*/
@@ -369,7 +370,7 @@
#define LSR_OE (1 << 1) /* Overrun Error */
#define LSR_DR (1 << 0) /* Data Ready */
-#define MCR_LOOP (1 << 4) */
+#define MCR_LOOP (1 << 4) */
#define MCR_OUT2 (1 << 3) /* force MSR_DCD in loopback mode */
#define MCR_OUT1 (1 << 2) /* force MSR_RI in loopback mode */
#define MCR_RTS (1 << 1) /* Request to Send */
@@ -414,7 +415,6 @@
IrSR_RCVEIR_UART_MODE | \
IrSR_XMITIR_IR_MODE)
-
/*
* I2C registers
*/
@@ -425,6 +425,38 @@
#define ISR __REG(0x40301698) /* I2C Status Register - ISR */
#define ISAR __REG(0x403016A0) /* I2C Slave Address Register - ISAR */
+/* ----- Control register bits ---------------------------------------- */
+
+#define ICR_START 0x1 /* start bit */
+#define ICR_STOP 0x2 /* stop bit */
+#define ICR_ACKNAK 0x4 /* send ACK(0) or NAK(1) */
+#define ICR_TB 0x8 /* transfer byte bit */
+#define ICR_MA 0x10 /* master abort */
+#define ICR_SCLE 0x20 /* master clock enable */
+#define ICR_IUE 0x40 /* unit enable */
+#define ICR_GCD 0x80 /* general call disable */
+#define ICR_ITEIE 0x100 /* enable tx interrupts */
+#define ICR_IRFIE 0x200 /* enable rx interrupts */
+#define ICR_BEIE 0x400 /* enable bus error ints */
+#define ICR_SSDIE 0x800 /* slave STOP detected int enable */
+#define ICR_ALDIE 0x1000 /* enable arbitration interrupt */
+#define ICR_SADIE 0x2000 /* slave address detected int enable */
+#define ICR_UR 0x4000 /* unit reset */
+#define ICR_FM 0x8000 /* Fast Mode */
+
+/* ----- Status register bits ----------------------------------------- */
+
+#define ISR_RWM 0x1 /* read/write mode */
+#define ISR_ACKNAK 0x2 /* ack/nak status */
+#define ISR_UB 0x4 /* unit busy */
+#define ISR_IBB 0x8 /* bus busy */
+#define ISR_SSD 0x10 /* slave stop detected */
+#define ISR_ALD 0x20 /* arbitration loss detected */
+#define ISR_ITE 0x40 /* tx buffer empty */
+#define ISR_IRF 0x80 /* rx buffer full */
+#define ISR_GCAD 0x100 /* general call address detected */
+#define ISR_SAD 0x200 /* slave address detected */
+#define ISR_BED 0x400 /* bus error no ACK/NAK */
/*
* Serial Audio Controller
@@ -524,24 +556,92 @@
/*
* USB Device Controller
*/
+#define UDC_RES1 __REG(0x40600004) /* UDC Undocumented - Reserved1 */
+#define UDC_RES2 __REG(0x40600008) /* UDC Undocumented - Reserved2 */
+#define UDC_RES3 __REG(0x4060000C) /* UDC Undocumented - Reserved3 */
#define UDCCR __REG(0x40600000) /* UDC Control Register */
+#define UDCCR_UDE (1 << 0) /* UDC enable */
+#define UDCCR_UDA (1 << 1) /* UDC active */
+#define UDCCR_RSM (1 << 2) /* Device resume */
+#define UDCCR_RESIR (1 << 3) /* Resume interrupt request */
+#define UDCCR_SUSIR (1 << 4) /* Suspend interrupt request */
+#define UDCCR_SRM (1 << 5) /* Suspend/resume interrupt mask */
+#define UDCCR_RSTIR (1 << 6) /* Reset interrupt request */
+#define UDCCR_REM (1 << 7) /* Reset interrupt mask */
+
#define UDCCS0 __REG(0x40600010) /* UDC Endpoint 0 Control/Status Register */
+#define UDCCS0_OPR (1 << 0) /* OUT packet ready */
+#define UDCCS0_IPR (1 << 1) /* IN packet ready */
+#define UDCCS0_FTF (1 << 2) /* Flush Tx FIFO */
+#define UDCCS0_DRWF (1 << 3) /* Device remote wakeup feature */
+#define UDCCS0_SST (1 << 4) /* Sent stall */
+#define UDCCS0_FST (1 << 5) /* Force stall */
+#define UDCCS0_RNE (1 << 6) /* Receive FIFO no empty */
+#define UDCCS0_SA (1 << 7) /* Setup active */
+
+/* Bulk IN - Endpoint 1,6,11 */
#define UDCCS1 __REG(0x40600014) /* UDC Endpoint 1 (IN) Control/Status Register */
-#define UDCCS2 __REG(0x40600018) /* UDC Endpoint 2 (OUT) Control/Status Register */
-#define UDCCS3 __REG(0x4060001C) /* UDC Endpoint 3 (IN) Control/Status Register */
-#define UDCCS4 __REG(0x40600020) /* UDC Endpoint 4 (OUT) Control/Status Register */
-#define UDCCS5 __REG(0x40600024) /* UDC Endpoint 5 (Interrupt) Control/Status Register */
#define UDCCS6 __REG(0x40600028) /* UDC Endpoint 6 (IN) Control/Status Register */
-#define UDCCS7 __REG(0x4060002C) /* UDC Endpoint 7 (OUT) Control/Status Register */
-#define UDCCS8 __REG(0x40600030) /* UDC Endpoint 8 (IN) Control/Status Register */
-#define UDCCS9 __REG(0x40600034) /* UDC Endpoint 9 (OUT) Control/Status Register */
-#define UDCCS10 __REG(0x40600038) /* UDC Endpoint 10 (Interrupt) Control/Status Register */
#define UDCCS11 __REG(0x4060003C) /* UDC Endpoint 11 (IN) Control/Status Register */
+
+#define UDCCS_BI_TFS (1 << 0) /* Transmit FIFO service */
+#define UDCCS_BI_TPC (1 << 1) /* Transmit packet complete */
+#define UDCCS_BI_FTF (1 << 2) /* Flush Tx FIFO */
+#define UDCCS_BI_TUR (1 << 3) /* Transmit FIFO underrun */
+#define UDCCS_BI_SST (1 << 4) /* Sent stall */
+#define UDCCS_BI_FST (1 << 5) /* Force stall */
+#define UDCCS_BI_TSP (1 << 7) /* Transmit short packet */
+
+/* Bulk OUT - Endpoint 2,7,12 */
+#define UDCCS2 __REG(0x40600018) /* UDC Endpoint 2 (OUT) Control/Status Register */
+#define UDCCS7 __REG(0x4060002C) /* UDC Endpoint 7 (OUT) Control/Status Register */
#define UDCCS12 __REG(0x40600040) /* UDC Endpoint 12 (OUT) Control/Status Register */
+
+#define UDCCS_BO_RFS (1 << 0) /* Receive FIFO service */
+#define UDCCS_BO_RPC (1 << 1) /* Receive packet complete */
+#define UDCCS_BO_DME (1 << 3) /* DMA enable */
+#define UDCCS_BO_SST (1 << 4) /* Sent stall */
+#define UDCCS_BO_FST (1 << 5) /* Force stall */
+#define UDCCS_BO_RNE (1 << 6) /* Receive FIFO not empty */
+#define UDCCS_BO_RSP (1 << 7) /* Receive short packet */
+
+/* Isochronous IN - Endpoint 3,8,13 */
+#define UDCCS3 __REG(0x4060001C) /* UDC Endpoint 3 (IN) Control/Status Register */
+#define UDCCS8 __REG(0x40600030) /* UDC Endpoint 8 (IN) Control/Status Register */
#define UDCCS13 __REG(0x40600044) /* UDC Endpoint 13 (IN) Control/Status Register */
+
+#define UDCCS_II_TFS (1 << 0) /* Transmit FIFO service */
+#define UDCCS_II_TPC (1 << 1) /* Transmit packet complete */
+#define UDCCS_II_FTF (1 << 2) /* Flush Tx FIFO */
+#define UDCCS_II_TUR (1 << 3) /* Transmit FIFO underrun */
+#define UDCCS_II_TSP (1 << 7) /* Transmit short packet */
+
+/* Isochronous OUT - Endpoint 4,9,14 */
+#define UDCCS4 __REG(0x40600020) /* UDC Endpoint 4 (OUT) Control/Status Register */
+#define UDCCS9 __REG(0x40600034) /* UDC Endpoint 9 (OUT) Control/Status Register */
#define UDCCS14 __REG(0x40600048) /* UDC Endpoint 14 (OUT) Control/Status Register */
+
+#define UDCCS_IO_RFS (1 << 0) /* Receive FIFO service */
+#define UDCCS_IO_RPC (1 << 1) /* Receive packet complete */
+#define UDCCS_IO_ROF (1 << 3) /* Receive overflow */
+#define UDCCS_IO_DME (1 << 3) /* DMA enable */
+#define UDCCS_IO_RNE (1 << 6) /* Receive FIFO not empty */
+#define UDCCS_IO_RSP (1 << 7) /* Receive short packet */
+
+/* Interrupt IN - Endpoint 5,10,15 */
+#define UDCCS5 __REG(0x40600024) /* UDC Endpoint 5 (Interrupt) Control/Status Register */
+#define UDCCS10 __REG(0x40600038) /* UDC Endpoint 10 (Interrupt) Control/Status Register */
#define UDCCS15 __REG(0x4060004C) /* UDC Endpoint 15 (Interrupt) Control/Status Register */
+
+#define UDCCS_INT_TFS (1 << 0) /* Transmit FIFO service */
+#define UDCCS_INT_TPC (1 << 1) /* Transmit packet complete */
+#define UDCCS_INT_FTF (1 << 2) /* Flush Tx FIFO */
+#define UDCCS_INT_TUR (1 << 3) /* Transmit FIFO underrun */
+#define UDCCS_INT_SST (1 << 4) /* Sent stall */
+#define UDCCS_INT_FST (1 << 5) /* Force stall */
+#define UDCCS_INT_TSP (1 << 7) /* Transmit short packet */
+
#define UFNRH __REG(0x40600060) /* UDC Frame Number Register High */
#define UFNRL __REG(0x40600064) /* UDC Frame Number Register Low */
#define UBCR2 __REG(0x40600068) /* UDC Byte Count Reg 2 */
@@ -566,11 +666,51 @@
#define UDDR13 __REG(0x40600C00) /* UDC Endpoint 13 Data Register */
#define UDDR14 __REG(0x40600E00) /* UDC Endpoint 14 Data Register */
#define UDDR15 __REG(0x406000E0) /* UDC Endpoint 15 Data Register */
+
#define UICR0 __REG(0x40600050) /* UDC Interrupt Control Register 0 */
+
+#define UICR0_IM0 (1 << 0) /* Interrupt mask ep 0 */
+#define UICR0_IM1 (1 << 1) /* Interrupt mask ep 1 */
+#define UICR0_IM2 (1 << 2) /* Interrupt mask ep 2 */
+#define UICR0_IM3 (1 << 3) /* Interrupt mask ep 3 */
+#define UICR0_IM4 (1 << 4) /* Interrupt mask ep 4 */
+#define UICR0_IM5 (1 << 5) /* Interrupt mask ep 5 */
+#define UICR0_IM6 (1 << 6) /* Interrupt mask ep 6 */
+#define UICR0_IM7 (1 << 7) /* Interrupt mask ep 7 */
+
#define UICR1 __REG(0x40600054) /* UDC Interrupt Control Register 1 */
+
+#define UICR1_IM8 (1 << 0) /* Interrupt mask ep 8 */
+#define UICR1_IM9 (1 << 1) /* Interrupt mask ep 9 */
+#define UICR1_IM10 (1 << 2) /* Interrupt mask ep 10 */
+#define UICR1_IM11 (1 << 3) /* Interrupt mask ep 11 */
+#define UICR1_IM12 (1 << 4) /* Interrupt mask ep 12 */
+#define UICR1_IM13 (1 << 5) /* Interrupt mask ep 13 */
+#define UICR1_IM14 (1 << 6) /* Interrupt mask ep 14 */
+#define UICR1_IM15 (1 << 7) /* Interrupt mask ep 15 */
+
#define USIR0 __REG(0x40600058) /* UDC Status Interrupt Register 0 */
+
+#define USIR0_IR0 (1 << 0) /* Interrup request ep 0 */
+#define USIR0_IR1 (1 << 1) /* Interrup request ep 1 */
+#define USIR0_IR2 (1 << 2) /* Interrup request ep 2 */
+#define USIR0_IR3 (1 << 3) /* Interrup request ep 3 */
+#define USIR0_IR4 (1 << 4) /* Interrup request ep 4 */
+#define USIR0_IR5 (1 << 5) /* Interrup request ep 5 */
+#define USIR0_IR6 (1 << 6) /* Interrup request ep 6 */
+#define USIR0_IR7 (1 << 7) /* Interrup request ep 7 */
+
#define USIR1 __REG(0x4060005C) /* UDC Status Interrupt Register 1 */
+#define USIR1_IR8 (1 << 0) /* Interrup request ep 8 */
+#define USIR1_IR9 (1 << 1) /* Interrup request ep 9 */
+#define USIR1_IR10 (1 << 2) /* Interrup request ep 10 */
+#define USIR1_IR11 (1 << 3) /* Interrup request ep 11 */
+#define USIR1_IR12 (1 << 4) /* Interrup request ep 12 */
+#define USIR1_IR13 (1 << 5) /* Interrup request ep 13 */
+#define USIR1_IR14 (1 << 6) /* Interrup request ep 14 */
+#define USIR1_IR15 (1 << 7) /* Interrup request ep 15 */
+
/*
* Fast Infrared Communication Port
@@ -917,6 +1057,22 @@
#define PGSR2 __REG(0x40F00028) /* Power Manager GPIO Sleep State Register for GP[84-64] */
#define RCSR __REG(0x40F00030) /* Reset Controller Status Register */
+#define PSSR_RDH (1 << 5) /* Read Disable Hold */
+#define PSSR_PH (1 << 4) /* Peripheral Control Hold */
+#define PSSR_VFS (1 << 2) /* VDD Fault Status */
+#define PSSR_BFS (1 << 1) /* Battery Fault Status */
+#define PSSR_SSS (1 << 0) /* Software Sleep Status */
+
+#define PCFR_DS (1 << 3) /* Deep Sleep Mode */
+#define PCFR_FS (1 << 2) /* Float Static Chip Selects */
+#define PCFR_FP (1 << 1) /* Float PCMCIA controls */
+#define PCFR_OPDE (1 << 0) /* 3.6864 MHz oscillator power-down enable */
+
+#define RCSR_GPR (1 << 3) /* GPIO Reset */
+#define RCSR_SMR (1 << 2) /* Sleep Mode */
+#define RCSR_WDR (1 << 1) /* Watchdog Reset */
+#define RCSR_HWR (1 << 0) /* Hardware Reset */
+
/*
* SSP Serial Port Registers
@@ -1040,19 +1196,105 @@
#define LCCR0_BM (1 << 20) /* Branch mask */
#define LCCR0_OUM (1 << 21) /* Output FIFO underrun mask */
+#define LCCR1_PPL Fld (10, 0) /* Pixels Per Line - 1 */
+#define LCCR1_DisWdth(Pixel) /* Display Width [1..800 pix.] */ \
+ (((Pixel) - 1) << FShft (LCCR1_PPL))
+
+#define LCCR1_HSW Fld (6, 10) /* Horizontal Synchronization */
+#define LCCR1_HorSnchWdth(Tpix) /* Horizontal Synchronization */ \
+ /* pulse Width [1..64 Tpix] */ \
+ (((Tpix) - 1) << FShft (LCCR1_HSW))
+
+#define LCCR1_ELW Fld (8, 16) /* End-of-Line pixel clock Wait */
+ /* count - 1 [Tpix] */
+#define LCCR1_EndLnDel(Tpix) /* End-of-Line Delay */ \
+ /* [1..256 Tpix] */ \
+ (((Tpix) - 1) << FShft (LCCR1_ELW))
+
+#define LCCR1_BLW Fld (8, 24) /* Beginning-of-Line pixel clock */
+ /* Wait count - 1 [Tpix] */
+#define LCCR1_BegLnDel(Tpix) /* Beginning-of-Line Delay */ \
+ /* [1..256 Tpix] */ \
+ (((Tpix) - 1) << FShft (LCCR1_BLW))
+
+
+#define LCCR2_LPP Fld (10, 0) /* Line Per Panel - 1 */
+#define LCCR2_DisHght(Line) /* Display Height [1..1024 lines] */ \
+ (((Line) - 1) << FShft (LCCR2_LPP))
+
+#define LCCR2_VSW Fld (6, 10) /* Vertical Synchronization pulse */
+ /* Width - 1 [Tln] (L_FCLK) */
+#define LCCR2_VrtSnchWdth(Tln) /* Vertical Synchronization pulse */ \
+ /* Width [1..64 Tln] */ \
+ (((Tln) - 1) << FShft (LCCR2_VSW))
+
+#define LCCR2_EFW Fld (8, 16) /* End-of-Frame line clock Wait */
+ /* count [Tln] */
+#define LCCR2_EndFrmDel(Tln) /* End-of-Frame Delay */ \
+ /* [0..255 Tln] */ \
+ ((Tln) << FShft (LCCR2_EFW))
+
+#define LCCR2_BFW Fld (8, 24) /* Beginning-of-Frame line clock */
+ /* Wait count [Tln] */
+#define LCCR2_BegFrmDel(Tln) /* Beginning-of-Frame Delay */ \
+ /* [0..255 Tln] */ \
+ ((Tln) << FShft (LCCR2_BFW))
+
+#if 0
#define LCCR3_PCD (0xff) /* Pixel clock divisor */
#define LCCR3_ACB (0xff << 8) /* AC Bias pin frequency */
#define LCCR3_ACB_S 8
+#endif
+
#define LCCR3_API (0xf << 16) /* AC Bias pin trasitions per interrupt */
#define LCCR3_API_S 16
#define LCCR3_VSP (1 << 20) /* vertical sync polarity */
#define LCCR3_HSP (1 << 21) /* horizontal sync polarity */
#define LCCR3_PCP (1 << 22) /* pixel clock polarity */
#define LCCR3_OEP (1 << 23) /* output enable polarity */
+#if 0
#define LCCR3_BPP (7 << 24) /* bits per pixel */
#define LCCR3_BPP_S 24
+#endif
#define LCCR3_DPC (1 << 27) /* double pixel clock mode */
+
+#define LCCR3_PCD Fld (8, 0) /* Pixel Clock Divisor */
+#define LCCR3_PixClkDiv(Div) /* Pixel Clock Divisor */ \
+ (((Div) << FShft (LCCR3_PCD)))
+
+
+#define LCCR3_BPP Fld (3, 24) /* Bit Per Pixel */
+#define LCCR3_Bpp(Bpp) /* Bit Per Pixel */ \
+ (((Bpp) << FShft (LCCR3_BPP)))
+
+#define LCCR3_ACB Fld (8, 8) /* AC Bias */
+#define LCCR3_Acb(Acb) /* BAC Bias */ \
+ (((Acb) << FShft (LCCR3_ACB)))
+
+#define LCCR3_HorSnchH (LCCR3_HSP*0) /* Horizontal Synchronization */
+ /* pulse active High */
+#define LCCR3_HorSnchL (LCCR3_HSP*1) /* Horizontal Synchronization */
+
+#define LCCR3_VrtSnchH (LCCR3_VSP*0) /* Vertical Synchronization pulse */
+ /* active High */
+#define LCCR3_VrtSnchL (LCCR3_VSP*1) /* Vertical Synchronization pulse */
+ /* active Low */
+
+#define LCSR_LDD (1 << 0) /* LCD Disable Done */
+#define LCSR_SOF (1 << 1) /* Start of frame */
+#define LCSR_BER (1 << 2) /* Bus error */
+#define LCSR_ABC (1 << 3) /* AC Bias count */
+#define LCSR_IUL (1 << 4) /* input FIFO underrun Lower panel */
+#define LCSR_IUU (1 << 5) /* input FIFO underrun Upper panel */
+#define LCSR_OU (1 << 6) /* output FIFO underrun */
+#define LCSR_QD (1 << 7) /* quick disable */
+#define LCSR_EOF (1 << 8) /* end of frame */
+#define LCSR_BS (1 << 9) /* branch status */
+#define LCSR_SINT (1 << 10) /* subsequent interrupt */
+
+#define LDCMD_PAL (1 << 26) /* instructs DMA to load palette buffer */
+
#define LCSR_LDD (1 << 0) /* LCD Disable Done */
#define LCSR_SOF (1 << 1) /* Start of frame */
#define LCSR_BER (1 << 2) /* Bus error */
@@ -1071,45 +1313,7 @@
* Memory controller
*/
-#define MEMC_BASE __REG(0x48000000) /* Base of Memoriy Controller */
-#define MDCNFG __REG(0x48000000) /* SDRAM Configuration Register 0 */
-#define MDREFR __REG(0x48000004) /* SDRAM Refresh Control Register */
-#define MSC0 __REG(0x48000008) /* Static Memory Control Register 0 */
-#define MSC1 __REG(0x4800000C) /* Static Memory Control Register 1 */
-#define MSC2 __REG(0x48000010) /* Static Memory Control Register 2 */
-#define MECR __REG(0x48000014) /* Expansion Memory (PCMCIA/Compact Flash) Bus Configuration */
-#define SXLCR __REG(0x48000018) /* LCR value to be written to SDRAM-Timing Synchronous Flash */
-#define SXCNFG __REG(0x4800001C) /* Synchronous Static Memory Control Register */
-#define SXMRS __REG(0x48000024) /* MRS value to be written to Synchronous Flash or SMROM */
-#define MCMEM0 __REG(0x48000028) /* Card interface Common Memory Space Socket 0 Timing */
-#define MCMEM1 __REG(0x4800002C) /* Card interface Common Memory Space Socket 1 Timing */
-#define MCATT0 __REG(0x48000030) /* Card interface Attribute Space Socket 0 Timing Configuration */
-#define MCATT1 __REG(0x48000034) /* Card interface Attribute Space Socket 1 Timing Configuration */
-#define MCIO0 __REG(0x48000038) /* Card interface I/O Space Socket 0 Timing Configuration */
-#define MCIO1 __REG(0x4800003C) /* Card interface I/O Space Socket 1 Timing Configuration */
-#define MDMRS __REG(0x48000040) /* MRS value to be written to SDRAM */
-#define BOOT_DEF __REG(0x48000044) /* Read-Only Boot-Time Register. Contains BOOT_SEL and PKG_SEL */
-
-#define MDCNFG_DE0 0x00000001
-#define MDCNFG_DE1 0x00000002
-#define MDCNFG_DE2 0x00010000
-#define MDCNFG_DE3 0x00020000
-#define MDCNFG_DWID0 0x00000004
-
-#define MDREFR_E0PIN 0x00001000
-#define MDREFR_K0RUN 0x00002000
-#define MDREFR_K0DB2 0x00004000
-#define MDREFR_E1PIN 0x00008000
-#define MDREFR_K1RUN 0x00010000
-#define MDREFR_K1DB2 0x00020000
-#define MDREFR_K2RUN 0x00040000
-#define MDREFR_K2DB2 0x00080000
-#define MDREFR_APD 0x00100000
-#define MDREFR_SLFRSH 0x00400000
-#define MDREFR_K0FREE 0x00800000
-#define MDREFR_K1FREE 0x01000000
-#define MDREFR_K2FREE 0x02000000
-
+#define MEMC_BASE __REG(0x48000000) /* Base of Memory Controller */
#define MDCNFG_OFFSET 0x0
#define MDREFR_OFFSET 0x4
#define MSC0_OFFSET 0x8
@@ -1127,7 +1331,44 @@
#define MCIO0_OFFSET 0x38
#define MCIO1_OFFSET 0x3C
#define MDMRS_OFFSET 0x40
+
+#define MDCNFG __REG(0x48000000) /* SDRAM Configuration Register 0 */
+#define MDCNFG_DE0 0x00000001
+#define MDCNFG_DE1 0x00000002
+#define MDCNFG_DE2 0x00010000
+#define MDCNFG_DE3 0x00020000
+#define MDCNFG_DWID0 0x00000004
+
+#define MDREFR __REG(0x48000004) /* SDRAM Refresh Control Register */
+#define MSC0 __REG(0x48000008) /* Static Memory Control Register 0 */
+#define MSC1 __REG(0x4800000C) /* Static Memory Control Register 1 */
+#define MSC2 __REG(0x48000010) /* Static Memory Control Register 2 */
+#define MECR __REG(0x48000014) /* Expansion Memory (PCMCIA/Compact Flash) Bus Configuration */
+#define SXLCR __REG(0x48000018) /* LCR value to be written to SDRAM-Timing Synchronous Flash */
+#define SXCNFG __REG(0x4800001C) /* Synchronous Static Memory Control Register */
+#define SXMRS __REG(0x48000024) /* MRS value to be written to Synchronous Flash or SMROM */
+#define MCMEM0 __REG(0x48000028) /* Card interface Common Memory Space Socket 0 Timing */
+#define MCMEM1 __REG(0x4800002C) /* Card interface Common Memory Space Socket 1 Timing */
+#define MCATT0 __REG(0x48000030) /* Card interface Attribute Space Socket 0 Timing Configuration */
+#define MCATT1 __REG(0x48000034) /* Card interface Attribute Space Socket 1 Timing Configuration */
+#define MCIO0 __REG(0x48000038) /* Card interface I/O Space Socket 0 Timing Configuration */
+#define MCIO1 __REG(0x4800003C) /* Card interface I/O Space Socket 1 Timing Configuration */
+#define MDMRS __REG(0x48000040) /* MRS value to be written to SDRAM */
+#define BOOT_DEF __REG(0x48000044) /* Read-Only Boot-Time Register. Contains BOOT_SEL and PKG_SEL */
+
+#define MDREFR_K2FREE (1 << 25) /* SDRAM Free-Running Control */
+#define MDREFR_K1FREE (1 << 24) /* SDRAM Free-Running Control */
+#define MDREFR_K0FREE (1 << 23) /* SDRAM Free-Running Control */
+#define MDREFR_SLFRSH (1 << 22) /* SDRAM Self-Refresh Control/Status */
+#define MDREFR_APD (1 << 20) /* SDRAM/SSRAM Auto-Power-Down Enable */
+#define MDREFR_K2DB2 (1 << 19) /* SDCLK2 Divide by 2 Control/Status */
+#define MDREFR_K2RUN (1 << 18) /* SDCLK2 Run Control/Status */
+#define MDREFR_K1DB2 (1 << 17) /* SDCLK1 Divide by 2 Control/Status */
+#define MDREFR_K1RUN (1 << 16) /* SDCLK1 Run Control/Status */
+#define MDREFR_E1PIN (1 << 15) /* SDCKE1 Level Control/Status */
+#define MDREFR_K0DB2 (1 << 14) /* SDCLK0 Divide by 2 Control/Status */
+#define MDREFR_K0RUN (1 << 13) /* SDCLK0 Run Control/Status */
+#define MDREFR_E0PIN (1 << 12) /* SDCKE0 Level Control/Status */
-
-
+#endif
diff --git a/include/asm-arm/proc-armv/ptrace.h b/include/asm-arm/proc-armv/ptrace.h
index 51708b9..b32edfc 100644
--- a/include/asm-arm/proc-armv/ptrace.h
+++ b/include/asm-arm/proc-armv/ptrace.h
@@ -61,6 +61,8 @@
#define ARM_r0 uregs[0]
#define ARM_ORIG_r0 uregs[17]
+#define instruction_pointer(regs) ((regs)->ARM_ip)
+
#ifdef __KERNEL__
#define user_mode(regs) \