armv8: LS2080A: Rename LS2085A to reflect LS2080A
LS2080A is a prime personality of Freescale’s LS2085A. It is a non-AIOP
personality without support of DP-DDR, L2 switch, 1588, PCIe endpoint etc.
So renaming existing LS2085A code base to reflect LS2080A (Prime personality)
Signed-off-by: Pratiyush Mohan Srivastava <pratiyush.srivastava@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
[York Sun: Dropped #ifdef in cpu.c for cpu_type_list]
Reviewed-by: York Sun <yorksun@freescale.com>
diff --git a/board/freescale/ls2080a/Kconfig b/board/freescale/ls2080a/Kconfig
new file mode 100644
index 0000000..0b938ff
--- /dev/null
+++ b/board/freescale/ls2080a/Kconfig
@@ -0,0 +1,31 @@
+if TARGET_LS2080A_EMU
+
+config SYS_BOARD
+ default "ls2080a"
+
+config SYS_VENDOR
+ default "freescale"
+
+config SYS_SOC
+ default "fsl-layerscape"
+
+config SYS_CONFIG_NAME
+ default "ls2080a_emu"
+
+endif
+
+if TARGET_LS2080A_SIMU
+
+config SYS_BOARD
+ default "ls2080a"
+
+config SYS_VENDOR
+ default "freescale"
+
+config SYS_SOC
+ default "fsl-layerscape"
+
+config SYS_CONFIG_NAME
+ default "ls2080a_simu"
+
+endif
diff --git a/board/freescale/ls2080a/MAINTAINERS b/board/freescale/ls2080a/MAINTAINERS
new file mode 100644
index 0000000..bb25084
--- /dev/null
+++ b/board/freescale/ls2080a/MAINTAINERS
@@ -0,0 +1,8 @@
+LS2080A BOARD
+M: York Sun <yorksun@freescale.com>
+S: Maintained
+F: board/freescale/ls2080a/
+F: include/configs/ls2080a_emu.h
+F: configs/ls2080a_emu_defconfig
+F: include/configs/ls2080a_simu.h
+F: configs/ls2080a_simu_defconfig
diff --git a/board/freescale/ls2080a/Makefile b/board/freescale/ls2080a/Makefile
new file mode 100644
index 0000000..47c7c74
--- /dev/null
+++ b/board/freescale/ls2080a/Makefile
@@ -0,0 +1,8 @@
+#
+# Copyright 2014-15 Freescale Semiconductor
+#
+# SPDX-License-Identifier: GPL-2.0+
+#
+
+obj-y += ls2080a.o
+obj-y += ddr.o
diff --git a/board/freescale/ls2080a/README b/board/freescale/ls2080a/README
new file mode 100644
index 0000000..7e53f1f
--- /dev/null
+++ b/board/freescale/ls2080a/README
@@ -0,0 +1,27 @@
+Freescale ls2080a_emu
+
+This is a emulator target with limited peripherals.
+
+Memory map from core's view
+
+0x00_0000_0000 .. 0x00_000F_FFFF Boot Rom
+0x00_0100_0000 .. 0x00_0FFF_FFFF CCSR
+0x00_1800_0000 .. 0x00_181F_FFFF OCRAM
+0x00_3000_0000 .. 0x00_3FFF_FFFF IFC region #1
+0x00_8000_0000 .. 0x00_FFFF_FFFF DDR region #1
+0x05_1000_0000 .. 0x05_FFFF_FFFF IFC region #2
+0x80_8000_0000 .. 0xFF_FFFF_FFFF DDR region #2
+
+Other addresses are either reserved, or not used directly by u-boot.
+This list should be updated when more addresses are used.
+
+Booting Linux flavors which do not support 48-bit VA (< Linux 3.18)
+-------------------------------------------------------------------
+One needs to use appropriate bootargs to boot Linux flavors which do
+not support 48-bit VA (for e.g. < Linux 3.18) by appending mem=2048M, as shown
+below:
+
+=> setenv bootargs 'console=ttyS1,115200 root=/dev/ram
+ earlycon=uart8250,mmio,0x21c0600,115200 default_hugepagesz=2m hugepagesz=2m
+ hugepages=16 mem=2048M'
+
diff --git a/board/freescale/ls2080a/ddr.c b/board/freescale/ls2080a/ddr.c
new file mode 100644
index 0000000..47d73ef
--- /dev/null
+++ b/board/freescale/ls2080a/ddr.c
@@ -0,0 +1,207 @@
+/*
+ * Copyright 2014 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <fsl_ddr_sdram.h>
+#include <fsl_ddr_dimm_params.h>
+#include "ddr.h"
+
+DECLARE_GLOBAL_DATA_PTR;
+
+void fsl_ddr_board_options(memctl_options_t *popts,
+ dimm_params_t *pdimm,
+ unsigned int ctrl_num)
+{
+ const struct board_specific_parameters *pbsp, *pbsp_highest = NULL;
+ ulong ddr_freq;
+
+ if (ctrl_num > 3) {
+ printf("Not supported controller number %d\n", ctrl_num);
+ return;
+ }
+ if (!pdimm->n_ranks)
+ return;
+
+ /*
+ * we use identical timing for all slots. If needed, change the code
+ * to pbsp = rdimms[ctrl_num] or pbsp = udimms[ctrl_num];
+ */
+ if (popts->registered_dimm_en)
+ pbsp = rdimms[ctrl_num];
+ else
+ pbsp = udimms[ctrl_num];
+
+
+ /* Get clk_adjust, wrlvl_start, wrlvl_ctl, according to the board ddr
+ * freqency and n_banks specified in board_specific_parameters table.
+ */
+ ddr_freq = get_ddr_freq(0) / 1000000;
+ while (pbsp->datarate_mhz_high) {
+ if (pbsp->n_ranks == pdimm->n_ranks &&
+ (pdimm->rank_density >> 30) >= pbsp->rank_gb) {
+ if (ddr_freq <= pbsp->datarate_mhz_high) {
+ popts->clk_adjust = pbsp->clk_adjust;
+ popts->wrlvl_start = pbsp->wrlvl_start;
+ popts->wrlvl_ctl_2 = pbsp->wrlvl_ctl_2;
+ popts->wrlvl_ctl_3 = pbsp->wrlvl_ctl_3;
+ goto found;
+ }
+ pbsp_highest = pbsp;
+ }
+ pbsp++;
+ }
+
+ if (pbsp_highest) {
+ printf("Error: board specific timing not found for data rate %lu MT/s\n"
+ "Trying to use the highest speed (%u) parameters\n",
+ ddr_freq, pbsp_highest->datarate_mhz_high);
+ popts->clk_adjust = pbsp_highest->clk_adjust;
+ popts->wrlvl_start = pbsp_highest->wrlvl_start;
+ popts->wrlvl_ctl_2 = pbsp->wrlvl_ctl_2;
+ popts->wrlvl_ctl_3 = pbsp->wrlvl_ctl_3;
+ } else {
+ panic("DIMM is not supported by this board");
+ }
+found:
+ debug("Found timing match: n_ranks %d, data rate %d, rank_gb %d\n"
+ "\tclk_adjust %d, wrlvl_start %d, wrlvl_ctrl_2 0x%x, wrlvl_ctrl_3 0x%x\n",
+ pbsp->n_ranks, pbsp->datarate_mhz_high, pbsp->rank_gb,
+ pbsp->clk_adjust, pbsp->wrlvl_start, pbsp->wrlvl_ctl_2,
+ pbsp->wrlvl_ctl_3);
+#ifdef CONFIG_SYS_FSL_HAS_DP_DDR
+ if (ctrl_num == CONFIG_DP_DDR_CTRL) {
+ /* force DDR bus width to 32 bits */
+ popts->data_bus_width = 1;
+ popts->otf_burst_chop_en = 0;
+ popts->burst_length = DDR_BL8;
+ popts->bstopre = 0; /* enable auto precharge */
+ }
+#endif
+ /*
+ * Factors to consider for half-strength driver enable:
+ * - number of DIMMs installed
+ */
+ popts->half_strength_driver_enable = 1;
+ /*
+ * Write leveling override
+ */
+ popts->wrlvl_override = 1;
+ popts->wrlvl_sample = 0xf;
+
+ /*
+ * Rtt and Rtt_WR override
+ */
+ popts->rtt_override = 0;
+
+ /* Enable ZQ calibration */
+ popts->zq_en = 1;
+
+#ifdef CONFIG_SYS_FSL_DDR4
+ popts->ddr_cdr1 = DDR_CDR1_DHC_EN | DDR_CDR1_ODT(DDR_CDR_ODT_80ohm);
+ popts->ddr_cdr2 = DDR_CDR2_ODT(DDR_CDR_ODT_80ohm) |
+ DDR_CDR2_VREF_OVRD(70); /* Vref = 70% */
+#else
+ /* DHC_EN =1, ODT = 75 Ohm */
+ popts->ddr_cdr1 = DDR_CDR1_DHC_EN | DDR_CDR1_ODT(DDR_CDR_ODT_75ohm);
+ popts->ddr_cdr2 = DDR_CDR2_ODT(DDR_CDR_ODT_75ohm);
+#endif
+}
+
+#ifdef CONFIG_SYS_DDR_RAW_TIMING
+dimm_params_t ddr_raw_timing = {
+ .n_ranks = 2,
+ .rank_density = 1073741824u,
+ .capacity = 2147483648,
+ .primary_sdram_width = 64,
+ .ec_sdram_width = 0,
+ .registered_dimm = 0,
+ .mirrored_dimm = 0,
+ .n_row_addr = 14,
+ .n_col_addr = 10,
+ .n_banks_per_sdram_device = 8,
+ .edc_config = 0,
+ .burst_lengths_bitmask = 0x0c,
+
+ .tckmin_x_ps = 937,
+ .caslat_x = 0x6FC << 4, /* 14,13,11,10,9,8,7,6 */
+ .taa_ps = 13090,
+ .twr_ps = 15000,
+ .trcd_ps = 13090,
+ .trrd_ps = 5000,
+ .trp_ps = 13090,
+ .tras_ps = 33000,
+ .trc_ps = 46090,
+ .trfc_ps = 160000,
+ .twtr_ps = 7500,
+ .trtp_ps = 7500,
+ .refresh_rate_ps = 7800000,
+ .tfaw_ps = 25000,
+};
+
+int fsl_ddr_get_dimm_params(dimm_params_t *pdimm,
+ unsigned int controller_number,
+ unsigned int dimm_number)
+{
+ const char dimm_model[] = "Fixed DDR on board";
+
+ if (((controller_number == 0) && (dimm_number == 0)) ||
+ ((controller_number == 1) && (dimm_number == 0))) {
+ memcpy(pdimm, &ddr_raw_timing, sizeof(dimm_params_t));
+ memset(pdimm->mpart, 0, sizeof(pdimm->mpart));
+ memcpy(pdimm->mpart, dimm_model, sizeof(dimm_model) - 1);
+ }
+
+ return 0;
+}
+#endif
+phys_size_t initdram(int board_type)
+{
+ phys_size_t dram_size;
+
+ puts("Initializing DDR....");
+
+ puts("using SPD\n");
+ dram_size = fsl_ddr_sdram();
+
+ return dram_size;
+}
+
+void dram_init_banksize(void)
+{
+#ifdef CONFIG_SYS_DP_DDR_BASE_PHY
+ phys_size_t dp_ddr_size;
+#endif
+
+ gd->bd->bi_dram[0].start = CONFIG_SYS_SDRAM_BASE;
+ if (gd->ram_size > CONFIG_SYS_LS2_DDR_BLOCK1_SIZE) {
+ gd->bd->bi_dram[0].size = CONFIG_SYS_LS2_DDR_BLOCK1_SIZE;
+ gd->bd->bi_dram[1].start = CONFIG_SYS_DDR_BLOCK2_BASE;
+ gd->bd->bi_dram[1].size = gd->ram_size -
+ CONFIG_SYS_LS2_DDR_BLOCK1_SIZE;
+ } else {
+ gd->bd->bi_dram[0].size = gd->ram_size;
+ }
+
+#ifdef CONFIG_SYS_DP_DDR_BASE_PHY
+ /* initialize DP-DDR here */
+ puts("DP-DDR: ");
+ /*
+ * DDR controller use 0 as the base address for binding.
+ * It is mapped to CONFIG_SYS_DP_DDR_BASE for core to access.
+ */
+ dp_ddr_size = fsl_other_ddr_sdram(CONFIG_SYS_DP_DDR_BASE_PHY,
+ CONFIG_DP_DDR_CTRL,
+ CONFIG_DP_DDR_NUM_CTRLS,
+ CONFIG_DP_DDR_DIMM_SLOTS_PER_CTLR,
+ NULL, NULL, NULL);
+ if (dp_ddr_size) {
+ gd->bd->bi_dram[2].start = CONFIG_SYS_DP_DDR_BASE;
+ gd->bd->bi_dram[2].size = dp_ddr_size;
+ } else {
+ puts("Not detected");
+ }
+#endif
+}
diff --git a/board/freescale/ls2080a/ddr.h b/board/freescale/ls2080a/ddr.h
new file mode 100644
index 0000000..9958a68
--- /dev/null
+++ b/board/freescale/ls2080a/ddr.h
@@ -0,0 +1,86 @@
+/*
+ * Copyright 2014 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#ifndef __DDR_H__
+#define __DDR_H__
+struct board_specific_parameters {
+ u32 n_ranks;
+ u32 datarate_mhz_high;
+ u32 rank_gb;
+ u32 clk_adjust;
+ u32 wrlvl_start;
+ u32 wrlvl_ctl_2;
+ u32 wrlvl_ctl_3;
+};
+
+/*
+ * These tables contain all valid speeds we want to override with board
+ * specific parameters. datarate_mhz_high values need to be in ascending order
+ * for each n_ranks group.
+ */
+
+static const struct board_specific_parameters udimm0[] = {
+ /*
+ * memory controller 0
+ * num| hi| rank| clk| wrlvl | wrlvl | wrlvl
+ * ranks| mhz| GB |adjst| start | ctl2 | ctl3
+ */
+ {2, 2140, 0, 4, 4, 0x0, 0x0},
+ {1, 2140, 0, 4, 4, 0x0, 0x0},
+ {}
+};
+
+/* DP-DDR DIMM */
+static const struct board_specific_parameters udimm2[] = {
+ /*
+ * memory controller 2
+ * num| hi| rank| clk| wrlvl | wrlvl | wrlvl
+ * ranks| mhz| GB |adjst| start | ctl2 | ctl3
+ */
+ {2, 2140, 0, 4, 4, 0x0, 0x0},
+ {1, 2140, 0, 4, 4, 0x0, 0x0},
+ {}
+};
+
+static const struct board_specific_parameters rdimm0[] = {
+ /*
+ * memory controller 0
+ * num| hi| rank| clk| wrlvl | wrlvl | wrlvl
+ * ranks| mhz| GB |adjst| start | ctl2 | ctl3
+ */
+ {4, 2140, 0, 5, 4, 0x0, 0x0},
+ {2, 2140, 0, 5, 4, 0x0, 0x0},
+ {1, 2140, 0, 4, 4, 0x0, 0x0},
+ {}
+};
+
+/* DP-DDR DIMM */
+static const struct board_specific_parameters rdimm2[] = {
+ /*
+ * memory controller 2
+ * num| hi| rank| clk| wrlvl | wrlvl | wrlvl
+ * ranks| mhz| GB |adjst| start | ctl2 | ctl3
+ */
+ {4, 2140, 0, 5, 4, 0x0, 0x0},
+ {2, 2140, 0, 5, 4, 0x0, 0x0},
+ {1, 2140, 0, 4, 4, 0x0, 0x0},
+ {}
+};
+
+static const struct board_specific_parameters *udimms[] = {
+ udimm0,
+ udimm0,
+ udimm2,
+};
+
+static const struct board_specific_parameters *rdimms[] = {
+ rdimm0,
+ rdimm0,
+ rdimm2,
+};
+
+
+#endif
diff --git a/board/freescale/ls2080a/ls2080a.c b/board/freescale/ls2080a/ls2080a.c
new file mode 100644
index 0000000..827fbf0
--- /dev/null
+++ b/board/freescale/ls2080a/ls2080a.c
@@ -0,0 +1,152 @@
+/*
+ * Copyright 2014 Freescale Semiconductor
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+#include <common.h>
+#include <malloc.h>
+#include <errno.h>
+#include <netdev.h>
+#include <fsl_ifc.h>
+#include <fsl_ddr.h>
+#include <asm/io.h>
+#include <fdt_support.h>
+#include <libfdt.h>
+#include <fsl_debug_server.h>
+#include <fsl-mc/fsl_mc.h>
+#include <environment.h>
+#include <asm/arch/soc.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+int board_init(void)
+{
+ init_final_memctl_regs();
+
+#ifdef CONFIG_ENV_IS_NOWHERE
+ gd->env_addr = (ulong)&default_environment[0];
+#endif
+
+ return 0;
+}
+
+int board_early_init_f(void)
+{
+ fsl_lsch3_early_init_f();
+ return 0;
+}
+
+void detail_board_ddr_info(void)
+{
+ puts("\nDDR ");
+ print_size(gd->bd->bi_dram[0].size + gd->bd->bi_dram[1].size, "");
+ print_ddr_info(0);
+#ifdef CONFIG_SYS_FSL_HAS_DP_DDR
+ if (gd->bd->bi_dram[2].size) {
+ puts("\nDP-DDR ");
+ print_size(gd->bd->bi_dram[2].size, "");
+ print_ddr_info(CONFIG_DP_DDR_CTRL);
+ }
+#endif
+}
+
+int dram_init(void)
+{
+ gd->ram_size = initdram(0);
+
+ return 0;
+}
+
+#if defined(CONFIG_ARCH_MISC_INIT)
+int arch_misc_init(void)
+{
+#ifdef CONFIG_FSL_DEBUG_SERVER
+ debug_server_init();
+#endif
+
+ return 0;
+}
+#endif
+
+unsigned long get_dram_size_to_hide(void)
+{
+ unsigned long dram_to_hide = 0;
+
+/* Carve the Debug Server private DRAM block from the end of DRAM */
+#ifdef CONFIG_FSL_DEBUG_SERVER
+ dram_to_hide += debug_server_get_dram_block_size();
+#endif
+
+/* Carve the MC private DRAM block from the end of DRAM */
+#ifdef CONFIG_FSL_MC_ENET
+ dram_to_hide += mc_get_dram_block_size();
+#endif
+
+ return roundup(dram_to_hide, CONFIG_SYS_MEM_TOP_HIDE_MIN);
+}
+
+int board_eth_init(bd_t *bis)
+{
+ int error = 0;
+
+#ifdef CONFIG_SMC91111
+ error = smc91111_initialize(0, CONFIG_SMC91111_BASE);
+#endif
+
+#ifdef CONFIG_FSL_MC_ENET
+ error = cpu_eth_init(bis);
+#endif
+ return error;
+}
+
+#ifdef CONFIG_FSL_MC_ENET
+void fdt_fixup_board_enet(void *fdt)
+{
+ int offset;
+
+ offset = fdt_path_offset(fdt, "/fsl-mc");
+
+ /*
+ * TODO: Remove this when backward compatibility
+ * with old DT node (fsl,dprc@0) is no longer needed.
+ */
+ if (offset < 0)
+ offset = fdt_path_offset(fdt, "/fsl,dprc@0");
+
+ if (offset < 0) {
+ printf("%s: ERROR: fsl-mc node not found in device tree (error %d)\n",
+ __func__, offset);
+ return;
+ }
+
+ if (get_mc_boot_status() == 0)
+ fdt_status_okay(fdt, offset);
+ else
+ fdt_status_fail(fdt, offset);
+}
+#endif
+
+#ifdef CONFIG_OF_BOARD_SETUP
+int ft_board_setup(void *blob, bd_t *bd)
+{
+ u64 base[CONFIG_NR_DRAM_BANKS];
+ u64 size[CONFIG_NR_DRAM_BANKS];
+
+ ft_cpu_setup(blob, bd);
+
+ /* fixup DT for the two GPP DDR banks */
+ base[0] = gd->bd->bi_dram[0].start;
+ size[0] = gd->bd->bi_dram[0].size;
+ base[1] = gd->bd->bi_dram[1].start;
+ size[1] = gd->bd->bi_dram[1].size;
+
+ fdt_fixup_memory_banks(blob, base, size, 2);
+
+#ifdef CONFIG_FSL_MC_ENET
+ fdt_fixup_board_enet(blob);
+ fsl_mc_ldpaa_exit(bd);
+#endif
+
+ return 0;
+}
+#endif