Blackfin: cm-bf537u: new board port
The CM-BF537U is similar to the CM-BF537E module, but enough to need its
own board port.
Signed-off-by: Harald Krapfenbauer <Harald.Krapfenbauer@bluetechnix.at>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
diff --git a/include/configs/cm-bf537u.h b/include/configs/cm-bf537u.h
new file mode 100644
index 0000000..d1870a8
--- /dev/null
+++ b/include/configs/cm-bf537u.h
@@ -0,0 +1,150 @@
+/*
+ * U-boot - Configuration file for CM-BF537U board
+ */
+
+#ifndef __CONFIG_CM_BF537U_H__
+#define __CONFIG_CM_BF537U_H__
+
+#include <asm/config-pre.h>
+
+
+/*
+ * Processor Settings
+ */
+#define CONFIG_BFIN_CPU bf537-0.2
+#define CONFIG_BFIN_BOOT_MODE BFIN_BOOT_BYPASS
+
+
+/*
+ * Clock Settings
+ * CCLK = (CLKIN * VCO_MULT) / CCLK_DIV
+ * SCLK = (CLKIN * VCO_MULT) / SCLK_DIV
+ */
+/* CONFIG_CLKIN_HZ is any value in Hz */
+#define CONFIG_CLKIN_HZ 30000000
+/* CLKIN_HALF controls the DF bit in PLL_CTL 0 = CLKIN */
+/* 1 = CLKIN / 2 */
+#define CONFIG_CLKIN_HALF 0
+/* PLL_BYPASS controls the BYPASS bit in PLL_CTL 0 = do not bypass */
+/* 1 = bypass PLL */
+#define CONFIG_PLL_BYPASS 0
+/* VCO_MULT controls the MSEL (multiplier) bits in PLL_CTL */
+/* Values can range from 0-63 (where 0 means 64) */
+#define CONFIG_VCO_MULT 18
+/* CCLK_DIV controls the core clock divider */
+/* Values can be 1, 2, 4, or 8 ONLY */
+#define CONFIG_CCLK_DIV 1
+/* SCLK_DIV controls the system clock divider */
+/* Values can range from 1-15 */
+#define CONFIG_SCLK_DIV 5
+/* Core voltage */
+#define CONFIG_VR_CTL_VAL (VLEV_110 | GAIN_20 | FREQ_1000)
+
+
+/*
+ * Memory Settings
+ */
+#define CONFIG_MEM_ADD_WDTH 9
+#define CONFIG_MEM_SIZE 32
+
+#define CONFIG_EBIU_SDRRC_VAL 0x3f8
+#define CONFIG_EBIU_SDGCTL_VAL 0x9111cd
+
+#define CONFIG_EBIU_AMGCTL_VAL (AMBEN_ALL)
+#define CONFIG_EBIU_AMBCTL0_VAL (B1WAT_7 | B1RAT_11 | B1HT_2 | B1ST_3 | B0WAT_7 | B0RAT_11 | B0HT_2 | B0ST_3)
+#define CONFIG_EBIU_AMBCTL1_VAL (B3WAT_7 | B3RAT_11 | B3HT_2 | B3ST_3 | B2WAT_7 | B2RAT_11 | B2HT_2 | B2ST_3)
+
+#define CONFIG_SYS_MONITOR_LEN (256 * 1024)
+#define CONFIG_SYS_MALLOC_LEN (128 * 1024)
+
+
+/*
+ * Network Settings
+ */
+#ifndef __ADSPBF534__
+#define ADI_CMDS_NETWORK 1
+#define CONFIG_NET_MULTI
+/* The next 3 lines are for use with SMSC on EXT-BF5xx-USB-ETH2 */
+#define CONFIG_SMC911X 1
+#define CONFIG_SMC911X_BASE 0x24000000
+#define CONFIG_SMC911X_16_BIT
+#endif
+#define CONFIG_HOSTNAME cm-bf537u
+/* Uncomment next line to use fixed MAC address */
+/* #define CONFIG_ETHADDR 02:80:ad:20:31:e8 */
+
+
+/*
+ * Flash Settings
+ */
+#define CONFIG_FLASH_CFI_DRIVER
+#define CONFIG_CFI_FLASH_USE_WEAK_ACCESSORS
+#define CONFIG_SYS_FLASH_BASE 0x20000000
+#define CONFIG_SYS_FLASH_CFI
+#define CONFIG_SYS_FLASH_PROTECTION
+#define CONFIG_SYS_MAX_FLASH_BANKS 1
+#define CONFIG_SYS_MAX_FLASH_SECT 35
+
+
+/*
+ * Env Storage Settings
+ */
+#define CONFIG_ENV_IS_IN_FLASH 1
+#define CONFIG_ENV_OFFSET 0x4000
+#define CONFIG_ENV_SIZE 0x2000
+#define CONFIG_ENV_SECT_SIZE 0x20000
+#if (CONFIG_BFIN_BOOT_MODE == BFIN_BOOT_BYPASS)
+#define ENV_IS_EMBEDDED
+#else
+#define ENV_IS_EMBEDDED_CUSTOM
+#endif
+#ifdef ENV_IS_EMBEDDED
+/* WARNING - the following is hand-optimized to fit within
+ * the sector before the environment sector. If it throws
+ * an error during compilation remove an object here to get
+ * it linked after the configuration sector.
+ */
+# define LDS_BOARD_TEXT \
+ cpu/blackfin/traps.o (.text .text.*); \
+ cpu/blackfin/interrupt.o (.text .text.*); \
+ cpu/blackfin/serial.o (.text .text.*); \
+ common/dlmalloc.o (.text .text.*); \
+ lib_generic/crc32.o (.text .text.*); \
+ . = DEFINED(env_offset) ? env_offset : .; \
+ common/env_embedded.o (.text .text.*);
+#endif
+
+
+/*
+ * I2C Settings
+ */
+#define CONFIG_BFIN_TWI_I2C 1
+#define CONFIG_HARD_I2C 1
+#define CONFIG_SYS_I2C_SPEED 50000
+#define CONFIG_SYS_I2C_SLAVE 0
+
+
+/*
+ * Misc Settings
+ */
+#define CONFIG_BAUDRATE 115200
+#define CONFIG_MISC_INIT_R
+#define CONFIG_RTC_BFIN
+#define CONFIG_UART_CONSOLE 0
+
+
+/*
+ * Pull in common ADI header for remaining command/environment setup
+ */
+#include <configs/bfin_adi_common.h>
+
+#undef CONFIG_BOOTCOMMAND
+#define CONFIG_BOOTCOMMAND "run flashboot"
+
+#undef CONFIG_EXTRA_ENV_SETTINGS
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ NAND_ENV_SETTINGS \
+ NETWORK_ENV_SETTINGS \
+ "flashboot=flread 20040000 1000000 280000; bootm 0x1000000\0"
+
+#endif