[PATCH] Add support for the AMCC Katmai (440SPe) eval board
Signed-off-by: Stefan Roese <sr@denx.de>
diff --git a/include/configs/katmai.h b/include/configs/katmai.h
new file mode 100644
index 0000000..c750e14
--- /dev/null
+++ b/include/configs/katmai.h
@@ -0,0 +1,415 @@
+/*
+ * (C) Copyright 2007
+ * Stefan Roese, DENX Software Engineering, sr@denx.de.
+ *
+ * (C) Copyright 2004 Paul Reynolds <PaulReynolds@lhsolutions.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+/************************************************************************
+ * katmai.h - configuration for AMCC Katmai (440SPe)
+ ***********************************************************************/
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/*-----------------------------------------------------------------------
+ * High Level Configuration Options
+ *----------------------------------------------------------------------*/
+#define CONFIG_KATMAI 1 /* Board is Katmai */
+#define CONFIG_4xx 1 /* ... PPC4xx family */
+#define CONFIG_440 1 /* ... PPC440 family */
+#define CONFIG_440SPE 1 /* Specifc SPe support */
+#undef CFG_DRAM_TEST /* Disable-takes long time */
+#define CONFIG_SYS_CLK_FREQ 33333333 /* external freq to pll */
+
+#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_pre_init */
+#define CONFIG_MISC_INIT_F 1 /* Use misc_init_f() */
+#define CONFIG_ADD_RAM_INFO 1 /* Print additional info */
+#undef CONFIG_SHOW_BOOT_PROGRESS
+
+/*-----------------------------------------------------------------------
+ * Base addresses -- Note these are effective addresses where the
+ * actual resources get mapped (not physical addresses)
+ *----------------------------------------------------------------------*/
+#define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */
+#define CFG_MALLOC_LEN (512 * 1024) /* Reserve 512 kB for malloc */
+
+#define CFG_SDRAM_BASE 0x00000000 /* _must_ be 0 */
+#define CFG_FLASH_BASE 0xff000000 /* start of FLASH */
+#define CFG_MONITOR_BASE TEXT_BASE
+#define CFG_PERIPHERAL_BASE 0xa0000000 /* internal peripherals */
+#define CFG_ISRAM_BASE 0x90000000 /* internal SRAM */
+
+#define CFG_PCI_MEMBASE 0x80000000 /* mapped PCI memory */
+#define CFG_PCI_BASE 0xd0000000 /* internal PCI regs */
+#define CFG_PCI_TARGBASE CFG_PCI_MEMBASE
+
+#define CFG_PCIE_MEMBASE 0xb0000000 /* mapped PCIe memory */
+#define CFG_PCIE_MEMSIZE 0x01000000
+#define CFG_PCIE_BASE 0xe0000000 /* PCIe UTL regs */
+
+#define CFG_PCIE0_CFGBASE 0xc0000000
+#define CFG_PCIE0_XCFGBASE 0xc0000400
+#define CFG_PCIE1_CFGBASE 0xc0001000
+#define CFG_PCIE1_XCFGBASE 0xc0001400
+#define CFG_PCIE2_CFGBASE 0xc0002000
+#define CFG_PCIE2_XCFGBASE 0xc0002400
+
+/* System RAM mapped to PCI space */
+#define CONFIG_PCI_SYS_MEM_BUS CFG_SDRAM_BASE
+#define CONFIG_PCI_SYS_MEM_PHYS CFG_SDRAM_BASE
+#define CONFIG_PCI_SYS_MEM_SIZE (1024 * 1024 * 1024)
+
+#define CFG_ACE_BASE 0xe0000000 /* Xilinx ACE controller - Compact Flash */
+
+/*-----------------------------------------------------------------------
+ * Initial RAM & stack pointer (placed in internal SRAM)
+ *----------------------------------------------------------------------*/
+#define CFG_TEMP_STACK_OCM 1
+#define CFG_OCM_DATA_ADDR CFG_ISRAM_BASE
+#define CFG_INIT_RAM_ADDR CFG_ISRAM_BASE /* Initial RAM address */
+#define CFG_INIT_RAM_END 0x2000 /* End of used area in RAM */
+#define CFG_GBL_DATA_SIZE 128 /* num bytes initial data */
+
+#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
+#define CFG_POST_WORD_ADDR (CFG_GBL_DATA_OFFSET - 0x4)
+#define CFG_INIT_SP_OFFSET CFG_POST_WORD_ADDR
+
+/*-----------------------------------------------------------------------
+ * Serial Port
+ *----------------------------------------------------------------------*/
+#define CONFIG_SERIAL_MULTI 1
+#undef CONFIG_UART1_CONSOLE
+#undef CFG_EXT_SERIAL_CLOCK
+#define CONFIG_BAUDRATE 115200
+#define CFG_BAUDRATE_TABLE \
+ {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
+
+/*-----------------------------------------------------------------------
+ * DDR SDRAM
+ *----------------------------------------------------------------------*/
+#define CONFIG_SPD_EEPROM 1 /* Use SPD EEPROM for setup */
+#define SPD_EEPROM_ADDRESS {0x51, 0x52} /* SPD i2c spd addresses */
+#define IIC0_DIMM0_ADDR 0x51
+#define IIC0_DIMM1_ADDR 0x52
+#undef CONFIG_STRESS
+#undef ENABLE_ECC
+
+/*-----------------------------------------------------------------------
+ * I2C
+ *----------------------------------------------------------------------*/
+#define CONFIG_HARD_I2C 1 /* I2C with hardware support */
+#undef CONFIG_SOFT_I2C /* I2C bit-banged */
+#define CFG_I2C_SPEED 100000 /* I2C speed and slave address */
+#define CFG_I2C_SLAVE 0x7F
+
+#define CONFIG_I2C_MULTI_BUS
+#define CONFIG_I2C_CMD_TREE
+#define CFG_SPD_BUS_NUM 0 /* The I2C bus for SPD */
+
+#define IIC0_BOOTPROM_ADDR 0x50
+#define IIC0_ALT_BOOTPROM_ADDR 0x54
+
+#define CFG_I2C_MULTI_EEPROMS
+#define CFG_I2C_EEPROM_ADDR (0x50)
+#define CFG_I2C_EEPROM_ADDR_LEN 1
+#define CFG_EEPROM_PAGE_WRITE_ENABLE
+#define CFG_EEPROM_PAGE_WRITE_BITS 3
+#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10
+
+/* I2C RTC */
+#define CONFIG_RTC_M41T11 1
+#define CFG_RTC_BUS_NUM 1 /* The I2C bus for RTC */
+#define CFG_I2C_RTC_ADDR 0x68
+#define CFG_M41T11_BASE_YEAR 1900 /* play along with linux */
+
+/* I2C DTT */
+#define CONFIG_DTT_ADM1021 1 /* ADM1021 temp sensor support */
+#define CFG_DTT_BUS_NUM 1 /* The I2C bus for DTT */
+/*
+ * standard dtt sensor configuration - bottom bit will determine local or
+ * remote sensor of the ADM1021, the rest determines index into
+ * CFG_DTT_ADM1021 array below.
+ */
+#define CONFIG_DTT_SENSORS { 0, 1 }
+
+/*
+ * ADM1021 temp sensor configuration (see dtt/adm1021.c for details).
+ * there will be one entry in this array for each two (dummy) sensors in
+ * CONFIG_DTT_SENSORS.
+ *
+ * For Katmai board:
+ * - only one ADM1021
+ * - i2c addr 0x18
+ * - conversion rate 0x02 = 0.25 conversions/second
+ * - ALERT ouput disabled
+ * - local temp sensor enabled, min set to 0 deg, max set to 85 deg
+ * - remote temp sensor enabled, min set to 0 deg, max set to 85 deg
+ */
+#define CFG_DTT_ADM1021 { { 0x18, 0x02, 0, 1, 0, 85, 1, 0, 58} }
+
+/*-----------------------------------------------------------------------
+ * Environment
+ *----------------------------------------------------------------------*/
+#define CFG_ENV_IS_IN_FLASH 1 /* Environment uses flash */
+
+#define CONFIG_PREBOOT "echo;" \
+ "echo Type \"run flash_nfs\" to mount root filesystem over NFS;" \
+ "echo"
+
+#undef CONFIG_BOOTARGS
+
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ "netdev=eth0\0" \
+ "hostname=katmai\0" \
+ "nfsargs=setenv bootargs root=/dev/nfs rw " \
+ "nfsroot=${serverip}:${rootpath}\0" \
+ "ramargs=setenv bootargs root=/dev/ram rw\0" \
+ "addip=setenv bootargs ${bootargs} " \
+ "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \
+ ":${hostname}:${netdev}:off panic=1\0" \
+ "addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\
+ "flash_nfs=run nfsargs addip addtty;" \
+ "bootm ${kernel_addr}\0" \
+ "flash_self=run ramargs addip addtty;" \
+ "bootm ${kernel_addr} ${ramdisk_addr}\0" \
+ "net_nfs=tftp 200000 ${bootfile};run nfsargs addip addtty;" \
+ "bootm\0" \
+ "rootpath=/opt/eldk/ppc_4xx\0" \
+ "bootfile=katmai/uImage\0" \
+ "kernel_addr=fff10000\0" \
+ "ramdisk_addr=fff20000\0" \
+ "initrd_high=30000000\0" \
+ "load=tftp 200000 katmai/u-boot.bin\0" \
+ "update=protect off fffc0000 ffffffff;era fffc0000 ffffffff;" \
+ "cp.b ${fileaddr} fffc0000 ${filesize};" \
+ "setenv filesize;saveenv\0" \
+ "upd=run load;run update\0" \
+ "kozio=bootm ffc60000\0" \
+ ""
+#define CONFIG_BOOTCOMMAND "run flash_self"
+
+#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */
+
+#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
+#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
+
+#define CONFIG_COMMANDS (CONFIG_CMD_DFL | \
+ CFG_CMD_ASKENV | \
+ CFG_CMD_EEPROM | \
+ CFG_CMD_DATE | \
+ CFG_CMD_DHCP | \
+ CFG_CMD_DIAG | \
+ CFG_CMD_DTT | \
+ CFG_CMD_ELF | \
+ CFG_CMD_EXT2 | \
+ CFG_CMD_FAT | \
+ CFG_CMD_I2C | \
+ CFG_CMD_IRQ | \
+ CFG_CMD_MII | \
+ CFG_CMD_NET | \
+ CFG_CMD_NFS | \
+ CFG_CMD_PCI | \
+ CFG_CMD_PING | \
+ CFG_CMD_REGINFO | \
+ CFG_CMD_SDRAM)
+
+/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
+#include <cmd_confdefs.h>
+
+#define CONFIG_IBM_EMAC4_V4 1 /* 440SPe has this EMAC version */
+#define CONFIG_MII 1 /* MII PHY management */
+#define CONFIG_PHY_ADDR 1 /* PHY address, See schematics */
+#define CONFIG_HAS_ETH0
+#define CONFIG_PHY_RESET 1 /* reset phy upon startup */
+#define CONFIG_PHY_RESET_DELAY 1000
+#define CONFIG_CIS8201_PHY 1 /* Enable 'special' RGMII mode for Cicada phy */
+#define CONFIG_PHY_GIGE 1 /* Include GbE speed/duplex detection */
+#define CFG_RX_ETH_BUFFER 32 /* Number of ethernet rx buffers & descriptors */
+
+#define CONFIG_NETCONSOLE /* include NetConsole support */
+#define CONFIG_NET_MULTI /* needed for NetConsole */
+
+#undef CONFIG_WATCHDOG /* watchdog disabled */
+
+/*
+ * Miscellaneous configurable options
+ */
+#define CFG_LONGHELP /* undef to save memory */
+#define CFG_PROMPT "=> " /* Monitor Command Prompt */
+
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
+#else
+#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
+#endif
+#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
+#define CFG_MAXARGS 16 /* max number of command args */
+#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
+
+#define CFG_MEMTEST_START 0x0400000 /* memtest works on */
+#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
+
+#define CFG_LOAD_ADDR 0x100000 /* default load address */
+#define CFG_EXTBDINFO 1 /* To use extended board_into (bd_t) */
+
+#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
+
+#define CONFIG_CMDLINE_EDITING 1 /* add command line history */
+#define CONFIG_LOOPW 1 /* enable loopw command */
+#define CONFIG_MX_CYCLIC 1 /* enable mdc/mwc commands */
+#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */
+#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */
+
+#define CFG_4xx_RESET_TYPE 0x2 /* use chip reset on this board */
+
+/*-----------------------------------------------------------------------
+ * FLASH related
+ *----------------------------------------------------------------------*/
+#define CFG_FLASH_CFI
+#define CFG_FLASH_CFI_DRIVER
+#define CFG_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */
+#define CFG_FLASH_USE_BUFFER_WRITE 1 /* use buffered writes (20x faster) */
+
+#define CFG_FLASH_BANKS_LIST {CFG_FLASH_BASE}
+#define CFG_MAX_FLASH_BANKS 1 /* number of banks */
+#define CFG_MAX_FLASH_SECT 1024 /* sectors per device */
+
+#undef CFG_FLASH_CHECKSUM
+#define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
+#define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
+
+#define CFG_ENV_SECT_SIZE 0x20000 /* size of one complete sector */
+#define CFG_ENV_ADDR (CFG_MONITOR_BASE-CFG_ENV_SECT_SIZE)
+#define CFG_ENV_SIZE 0x4000 /* Total Size of Environment Sector */
+
+/* Address and size of Redundant Environment Sector */
+#define CFG_ENV_ADDR_REDUND (CFG_ENV_ADDR-CFG_ENV_SECT_SIZE)
+#define CFG_ENV_SIZE_REDUND (CFG_ENV_SIZE)
+
+/*-----------------------------------------------------------------------
+ * PCI stuff
+ *-----------------------------------------------------------------------
+ */
+/* General PCI */
+#define CONFIG_PCI /* include pci support */
+#define CONFIG_PCI_PNP 1 /* do pci plug-and-play */
+#define CONFIG_PCI_SCAN_SHOW 1 /* show pci devices on startup */
+#undef CONFIG_PCI_CONFIG_HOST_BRIDGE
+
+/* Board-specific PCI */
+#define CFG_PCI_PRE_INIT 1 /* enable board pci_pre_init() */
+#define CFG_PCI_TARGET_INIT /* let board init pci target */
+#undef CFG_PCI_MASTER_INIT
+
+#define CFG_PCI_SUBSYS_VENDORID 0x1014 /* IBM */
+#define CFG_PCI_SUBSYS_DEVICEID 0xcafe /* Whatever */
+/* #define CFG_PCI_SUBSYS_ID CFG_PCI_SUBSYS_DEVICEID */
+
+/*
+ * NETWORK Support (PCI):
+ */
+/* Support for Intel 82557/82559/82559ER chips. */
+#define CONFIG_EEPRO100
+
+/*-----------------------------------------------------------------------
+ * Xilinx System ACE support
+ *----------------------------------------------------------------------*/
+#define CONFIG_SYSTEMACE 1 /* Enable SystemACE support */
+#define CFG_SYSTEMACE_WIDTH 16 /* Data bus width is 16 */
+#define CFG_SYSTEMACE_BASE CFG_ACE_BASE
+#define CONFIG_DOS_PARTITION 1
+
+/*-----------------------------------------------------------------------
+ * External Bus Controller (EBC) Setup
+ *----------------------------------------------------------------------*/
+
+/* Memory Bank 0 (Flash) initialization */
+#define CFG_EBC_PB0AP (EBC_BXAP_BME_DISABLED | \
+ EBC_BXAP_TWT_ENCODE(7) | \
+ EBC_BXAP_BCE_DISABLE | \
+ EBC_BXAP_BCT_2TRANS | \
+ EBC_BXAP_CSN_ENCODE(0) | \
+ EBC_BXAP_OEN_ENCODE(0) | \
+ EBC_BXAP_WBN_ENCODE(0) | \
+ EBC_BXAP_WBF_ENCODE(0) | \
+ EBC_BXAP_TH_ENCODE(0) | \
+ EBC_BXAP_RE_DISABLED | \
+ EBC_BXAP_SOR_DELAYED | \
+ EBC_BXAP_BEM_WRITEONLY | \
+ EBC_BXAP_PEN_DISABLED)
+#define CFG_EBC_PB0CR (EBC_BXCR_BAS_ENCODE(CFG_FLASH_BASE) | \
+ EBC_BXCR_BS_16MB | \
+ EBC_BXCR_BU_RW | \
+ EBC_BXCR_BW_16BIT)
+
+/* Memory Bank 1 (Xilinx System ACE controller) initialization */
+#define CFG_EBC_PB1AP 0x7F8FFE80
+#define CFG_EBC_PB1CR (EBC_BXCR_BAS_ENCODE(CFG_ACE_BASE) | \
+ EBC_BXCR_BS_1MB | \
+ EBC_BXCR_BU_RW | \
+ EBC_BXCR_BW_16BIT)
+
+/*-------------------------------------------------------------------------
+ * Initialize EBC CONFIG -
+ * Keep the Default value, but the bit PDT which has to be set to 1 ?TBC
+ * default value : 0x07C00000 - 0 0 000 1 1 1 1 1 0000 0 00000 000000000000
+ *-------------------------------------------------------------------------*/
+#define CFG_EBC_CFG (EBC_CFG_LE_UNLOCK | \
+ EBC_CFG_PTD_ENABLE | \
+ EBC_CFG_RTC_16PERCLK | \
+ EBC_CFG_ATC_PREVIOUS | \
+ EBC_CFG_DTC_PREVIOUS | \
+ EBC_CFG_CTC_PREVIOUS | \
+ EBC_CFG_OEO_PREVIOUS | \
+ EBC_CFG_EMC_DEFAULT | \
+ EBC_CFG_PME_DISABLE | \
+ EBC_CFG_PR_16)
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 8 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CFG_BOOTMAPSZ (8 << 20) /*Initial Memory map for Linux*/
+/*-----------------------------------------------------------------------
+ * Cache Configuration
+ */
+#define CFG_DCACHE_SIZE 8192 /* For AMCC 405 CPUs */
+#define CFG_CACHELINE_SIZE 32 /* ... */
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */
+#endif
+
+/*
+ * Internal Definitions
+ *
+ * Boot Flags
+ */
+#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
+#define BOOTFLAG_WARM 0x02 /* Software reboot */
+
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
+#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
+#endif
+
+#endif /* __CONFIG_H */
diff --git a/include/ppc405.h b/include/ppc405.h
index e475fa5..a49912c 100644
--- a/include/ppc405.h
+++ b/include/ppc405.h
@@ -240,6 +240,7 @@
#define pbesr0 0x21 /* periph bus error status reg 0 */
#define pbesr1 0x22 /* periph bus error status reg 1 */
#define epcr 0x23 /* external periph control reg */
+#define EBC0_CFG 0x23 /* external bus configuration reg */
#ifdef CONFIG_405EP
/******************************************************************************
diff --git a/include/ppc440.h b/include/ppc440.h
index 91cff41..c24f5b7 100644
--- a/include/ppc440.h
+++ b/include/ppc440.h
@@ -533,9 +533,12 @@
#define SDRAM_MCSTAT_MIC_MASK 0x80000000 /* Memory init status mask */
#define SDRAM_MCSTAT_MIC_NOTCOMP 0x00000000 /* Mem init not complete */
#define SDRAM_MCSTAT_MIC_COMP 0x80000000 /* Mem init complete */
-#define SDRAM_MCSTAT_SRMS_MASK 0x80000000 /* Mem self refresh stat mask */
+#define SDRAM_MCSTAT_SRMS_MASK 0x40000000 /* Mem self refresh stat mask */
#define SDRAM_MCSTAT_SRMS_NOT_SF 0x00000000 /* Mem not in self refresh */
-#define SDRAM_MCSTAT_SRMS_SF 0x80000000 /* Mem in self refresh */
+#define SDRAM_MCSTAT_SRMS_SF 0x40000000 /* Mem in self refresh */
+#define SDRAM_MCSTAT_IDLE_MASK 0x20000000 /* Mem self refresh stat mask */
+#define SDRAM_MCSTAT_IDLE_NOT 0x00000000 /* Mem contr not idle */
+#define SDRAM_MCSTAT_IDLE 0x20000000 /* Mem contr idle */
/*-----------------------------------------------------------------------------+
| Memory Controller Options 1
@@ -730,6 +733,7 @@
#define SDRAM_WRDTR_LLWP_1_CYC 0x00000000
#define SDRAM_WRDTR_WTR_MASK 0x0E000000
#define SDRAM_WRDTR_WTR_0_DEG 0x06000000
+#define SDRAM_WRDTR_WTR_90_DEG_ADV 0x04000000
#define SDRAM_WRDTR_WTR_180_DEG_ADV 0x02000000
#define SDRAM_WRDTR_WTR_270_DEG_ADV 0x00000000
@@ -847,6 +851,7 @@
#define pbear 0x20 /* periph bus error addr reg */
#define pbesr 0x21 /* periph bus error status reg */
#define xbcfg 0x23 /* external bus configuration reg */
+#define EBC0_CFG 0x23 /* external bus configuration reg */
#define xbcid 0x24 /* external bus core id reg */
#if defined(CONFIG_440EP) || defined(CONFIG_440GR) || \