| CONFIG_ARM=y |
| CONFIG_ARCH_AT91=y |
| CONFIG_TARGET_SAMA5D4_XPLAINED=y |
| CONFIG_SPL_GPIO_SUPPORT=y |
| CONFIG_SPL_LIBCOMMON_SUPPORT=y |
| CONFIG_SPL_LIBGENERIC_SUPPORT=y |
| CONFIG_SYS_MALLOC_F_LEN=0x2000 |
| CONFIG_SPL_MMC_SUPPORT=y |
| CONFIG_SPL_SERIAL_SUPPORT=y |
| CONFIG_SPL_DRIVERS_MISC_SUPPORT=y |
| CONFIG_SPL_LIBDISK_SUPPORT=y |
| CONFIG_SPL_FAT_SUPPORT=y |
| CONFIG_DEFAULT_DEVICE_TREE="at91-sama5d4_xplained" |
| CONFIG_DEBUG_UART=y |
| CONFIG_FIT=y |
| CONFIG_SYS_EXTRA_OPTIONS="SAMA5D4,SYS_USE_MMC" |
| CONFIG_ENV_IS_IN_FAT=y |
| CONFIG_BOOTDELAY=3 |
| CONFIG_USE_BOOTARGS=y |
| CONFIG_BOOTARGS="console=ttyS0,115200 earlyprintk root=/dev/mmcblk0p2 rw rootwait" |
| # CONFIG_DISPLAY_BOARDINFO is not set |
| CONFIG_SPL=y |
| CONFIG_SPL_SEPARATE_BSS=y |
| CONFIG_HUSH_PARSER=y |
| CONFIG_CMD_BOOTZ=y |
| # CONFIG_CMD_IMI is not set |
| # CONFIG_CMD_IMLS is not set |
| # CONFIG_CMD_FLASH is not set |
| # CONFIG_CMD_FPGA is not set |
| # CONFIG_CMD_LOADS is not set |
| CONFIG_CMD_MMC=y |
| CONFIG_CMD_NAND=y |
| CONFIG_CMD_SF=y |
| CONFIG_CMD_USB=y |
| CONFIG_CMD_DHCP=y |
| CONFIG_CMD_PING=y |
| CONFIG_CMD_FAT=y |
| CONFIG_OF_CONTROL=y |
| CONFIG_SPL_OF_CONTROL=y |
| CONFIG_OF_SPL_REMOVE_PROPS="interrupts interrupt-parent dma-names dmas" |
| CONFIG_DM=y |
| CONFIG_SPL_DM=y |
| CONFIG_CLK=y |
| CONFIG_SPL_CLK=y |
| CONFIG_CLK_AT91=y |
| CONFIG_AT91_UTMI=y |
| CONFIG_AT91_H32MX=y |
| CONFIG_DM_GPIO=y |
| CONFIG_AT91_GPIO=y |
| CONFIG_DM_MMC=y |
| CONFIG_GENERIC_ATMEL_MCI=y |
| CONFIG_DM_SPI_FLASH=y |
| CONFIG_SPI_FLASH=y |
| CONFIG_SPI_FLASH_ATMEL=y |
| CONFIG_DM_ETH=y |
| CONFIG_MACB=y |
| CONFIG_PINCTRL=y |
| CONFIG_SPL_PINCTRL=y |
| CONFIG_PINCTRL_AT91=y |
| CONFIG_DM_SERIAL=y |
| CONFIG_DEBUG_UART_ATMEL=y |
| CONFIG_DEBUG_UART_BASE=0xfc00c000 |
| CONFIG_DEBUG_UART_CLOCK=100000000 |
| CONFIG_DEBUG_UART_BOARD_INIT=y |
| CONFIG_DEBUG_UART_ANNOUNCE=y |
| CONFIG_ATMEL_USART=y |
| CONFIG_DM_SPI=y |
| CONFIG_ATMEL_SPI=y |
| CONFIG_USB=y |
| CONFIG_DM_USB=y |
| CONFIG_USB_EHCI_HCD=y |
| CONFIG_USB_STORAGE=y |
| CONFIG_USB_GADGET=y |
| CONFIG_USB_GADGET_ATMEL_USBA=y |