arm: imx: add i.MX6SLL EVK board support
Add i.MX6SLL EVK board support.
1. Add imx6sll-evk device tree.
2. Enable SDHC/I2C/UART.
3. Enable REGULATOR/PMIC/I2C/GPIO/SDHC/PINCTRL driver.
Boot Log:
U-Boot 2016.11-00127-gc635871-dirty (Nov 24 2016 - 13:28:19 +0800)
CPU: Freescale i.MX6SLL rev1.0 at 792MHz
CPU: Commercial temperature grade (0C to 95C)Reset cause: POR
Model: Freescale i.MX6SLL EVK Board
Board: MX6SLL EVK
DRAM: 2 GiB
i2c bus 0 at 35258368, no gpio pinctrl state.
PMIC: PFUZE100! DEV_ID=0x10 REV_ID=0x21
MMC: FSL_SDHC: 0, FSL_SDHC: 1, FSL_SDHC: 2
In: serial
Out: serial
Err: serial
Net: CPU Net Initialization Failed
No ethernet found.
Hit any key to stop autoboot: 0
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
diff --git a/board/freescale/mx6sllevk/Kconfig b/board/freescale/mx6sllevk/Kconfig
new file mode 100644
index 0000000..4ba9bbf
--- /dev/null
+++ b/board/freescale/mx6sllevk/Kconfig
@@ -0,0 +1,12 @@
+if TARGET_MX6SLLEVK
+
+config SYS_BOARD
+ default "mx6sllevk"
+
+config SYS_VENDOR
+ default "freescale"
+
+config SYS_CONFIG_NAME
+ default "mx6sllevk"
+
+endif
diff --git a/board/freescale/mx6sllevk/Makefile b/board/freescale/mx6sllevk/Makefile
new file mode 100644
index 0000000..667fcb0
--- /dev/null
+++ b/board/freescale/mx6sllevk/Makefile
@@ -0,0 +1,6 @@
+# (C) Copyright 2016 Freescale Semiconductor, Inc.
+#
+# SPDX-License-Identifier: GPL-2.0+
+#
+
+obj-y := mx6sllevk.o
diff --git a/board/freescale/mx6sllevk/imximage.cfg b/board/freescale/mx6sllevk/imximage.cfg
new file mode 100644
index 0000000..53fb74f
--- /dev/null
+++ b/board/freescale/mx6sllevk/imximage.cfg
@@ -0,0 +1,121 @@
+/*
+ * Copyright (C) 2016 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ *
+ * Refer docs/README.imxmage for more details about how-to configure
+ * and create imximage boot image
+ *
+ * The syntax is taken as close as possible with the kwbimage
+ */
+
+#define __ASSEMBLY__
+#include <config.h>
+
+/* image version */
+
+IMAGE_VERSION 2
+
+/*
+ * Boot Device : one of
+ * spi, sd (the board has no nand neither onenand)
+ */
+
+BOOT_FROM sd
+
+#ifdef CONFIG_SECURE_BOOT
+CSF CONFIG_CSF_SIZE
+#endif
+
+/*
+ * Device Configuration Data (DCD)
+ *
+ * Each entry must have the format:
+ * Addr-type Address Value
+ *
+ * where:
+ * Addr-type register length (1,2 or 4 bytes)
+ * Address absolute address of the register
+ * value value to be stored in the register
+ */
+
+/* Enable all clocks */
+DATA 4 0x020c4068 0xffffffff
+DATA 4 0x020c406c 0xffffffff
+DATA 4 0x020c4070 0xffffffff
+DATA 4 0x020c4074 0xffffffff
+DATA 4 0x020c4078 0xffffffff
+DATA 4 0x020c407c 0xffffffff
+DATA 4 0x020c4080 0xffffffff
+
+DATA 4 0x020E0550 0x00080000
+DATA 4 0x020E0534 0x00000000
+DATA 4 0x020E02AC 0x00000030
+DATA 4 0x020E0548 0x00000030
+DATA 4 0x020E052C 0x00000030
+DATA 4 0x020E0530 0x00020000
+DATA 4 0x020E02B0 0x00003030
+DATA 4 0x020E02B4 0x00003030
+DATA 4 0x020E02B8 0x00003030
+DATA 4 0x020E02BC 0x00003030
+DATA 4 0x020E0540 0x00020000
+DATA 4 0x020E0544 0x00000030
+DATA 4 0x020E054C 0x00000030
+DATA 4 0x020E0554 0x00000030
+DATA 4 0x020E0558 0x00000030
+DATA 4 0x020E0294 0x00000030
+DATA 4 0x020E0298 0x00000030
+DATA 4 0x020E029C 0x00000030
+DATA 4 0x020E02A0 0x00000030
+DATA 4 0x020E02C0 0x00082030
+
+DATA 4 0x021B001C 0x00008000
+
+DATA 4 0x021B0800 0xA1390003
+DATA 4 0x021B085c 0x084700C7
+DATA 4 0x021B0890 0x00400000
+DATA 4 0x021B0848 0x3F393B3C
+DATA 4 0x021B0850 0x262C3826
+DATA 4 0x021B081C 0x33333333
+DATA 4 0x021B0820 0x33333333
+DATA 4 0x021B0824 0x33333333
+DATA 4 0x021B0828 0x33333333
+
+DATA 4 0x021B082C 0xf3333333
+DATA 4 0x021B0830 0xf3333333
+DATA 4 0x021B0834 0xf3333333
+DATA 4 0x021B0838 0xf3333333
+DATA 4 0x021B08C0 0x24922492
+DATA 4 0x021B08b8 0x00000800
+
+DATA 4 0x021B0004 0x00020052
+DATA 4 0x021B000C 0x53574333
+DATA 4 0x021B0010 0x00100B22
+DATA 4 0x021B0038 0x00170778
+DATA 4 0x021B0014 0x00C700DB
+DATA 4 0x021B0018 0x00201718
+DATA 4 0x021B002C 0x0F9F26D2
+DATA 4 0x021B0030 0x009F0E10
+DATA 4 0x021B0040 0x0000005F
+DATA 4 0x021B0000 0xC4190000
+
+DATA 4 0x021B083C 0x20000000
+
+DATA 4 0x021B001C 0x00008050
+DATA 4 0x021B001C 0x00008058
+DATA 4 0x021B001C 0x003F8030
+DATA 4 0x021B001C 0x003F8038
+DATA 4 0x021B001C 0xFF0A8030
+DATA 4 0x021B001C 0xFF0A8038
+DATA 4 0x021B001C 0x04028030
+DATA 4 0x021B001C 0x04028038
+DATA 4 0x021B001C 0x83018030
+DATA 4 0x021B001C 0x83018038
+DATA 4 0x021B001C 0x01038030
+DATA 4 0x021B001C 0x01038038
+
+DATA 4 0x021B0020 0x00001800
+DATA 4 0x021B0800 0xA1390003
+DATA 4 0x021B0004 0x00020052
+DATA 4 0x021B0404 0x00011006
+DATA 4 0x021B001C 0x00000000
diff --git a/board/freescale/mx6sllevk/mx6sllevk.c b/board/freescale/mx6sllevk/mx6sllevk.c
new file mode 100644
index 0000000..74a27a3
--- /dev/null
+++ b/board/freescale/mx6sllevk/mx6sllevk.c
@@ -0,0 +1,131 @@
+/*
+ * Copyright (C) 2016 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <asm/arch/clock.h>
+#include <asm/arch/crm_regs.h>
+#include <asm/arch/iomux.h>
+#include <asm/arch/imx-regs.h>
+#include <asm/arch/mx6-pins.h>
+#include <asm/arch/sys_proto.h>
+#include <asm/gpio.h>
+#include <asm/imx-common/iomux-v3.h>
+#include <asm/imx-common/boot_mode.h>
+#include <asm/io.h>
+#include <common.h>
+#include <linux/sizes.h>
+#include <mmc.h>
+#include <power/pmic.h>
+#include <power/pfuze100_pmic.h>
+#include "../common/pfuze.h"
+
+DECLARE_GLOBAL_DATA_PTR;
+
+#define UART_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE | \
+ PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED | \
+ PAD_CTL_DSE_40ohm | PAD_CTL_SRE_FAST | PAD_CTL_HYS)
+
+int dram_init(void)
+{
+ gd->ram_size = imx_ddr_size();
+
+ return 0;
+}
+
+static iomux_v3_cfg_t const uart1_pads[] = {
+ MX6_PAD_UART1_TXD__UART1_DCE_TX | MUX_PAD_CTRL(UART_PAD_CTRL),
+ MX6_PAD_UART1_RXD__UART1_DCE_RX | MUX_PAD_CTRL(UART_PAD_CTRL),
+};
+
+static iomux_v3_cfg_t const wdog_pads[] = {
+ MX6_PAD_WDOG_B__WDOG1_B | MUX_PAD_CTRL(NO_PAD_CTRL),
+};
+
+static void setup_iomux_uart(void)
+{
+ imx_iomux_v3_setup_multiple_pads(uart1_pads, ARRAY_SIZE(uart1_pads));
+}
+
+#ifdef CONFIG_DM_PMIC_PFUZE100
+int power_init_board(void)
+{
+ struct udevice *dev;
+ int ret;
+ u32 dev_id, rev_id, i;
+ u32 switch_num = 6;
+ u32 offset = PFUZE100_SW1CMODE;
+
+ ret = pmic_get("pfuze100", &dev);
+ if (ret == -ENODEV)
+ return 0;
+
+ if (ret != 0)
+ return ret;
+
+ dev_id = pmic_reg_read(dev, PFUZE100_DEVICEID);
+ rev_id = pmic_reg_read(dev, PFUZE100_REVID);
+ printf("PMIC: PFUZE100! DEV_ID=0x%x REV_ID=0x%x\n", dev_id, rev_id);
+
+
+ /* Init mode to APS_PFM */
+ pmic_reg_write(dev, PFUZE100_SW1ABMODE, APS_PFM);
+
+ for (i = 0; i < switch_num - 1; i++)
+ pmic_reg_write(dev, offset + i * SWITCH_SIZE, APS_PFM);
+
+ /* set SW1AB staby volatage 0.975V */
+ pmic_clrsetbits(dev, PFUZE100_SW1ABSTBY, 0x3f, 0x1b);
+
+ /* set SW1AB/VDDARM step ramp up time from 16us to 4us/25mV */
+ pmic_clrsetbits(dev, PFUZE100_SW1ABCONF, 0xc0, 0x40);
+
+ /* set SW1C staby volatage 0.975V */
+ pmic_clrsetbits(dev, PFUZE100_SW1CSTBY, 0x3f, 0x1b);
+
+ /* set SW1C/VDDSOC step ramp up time to from 16us to 4us/25mV */
+ pmic_clrsetbits(dev, PFUZE100_SW1CCONF, 0xc0, 0x40);
+
+ return 0;
+}
+#endif
+
+int board_early_init_f(void)
+{
+ setup_iomux_uart();
+
+ return 0;
+}
+
+int board_init(void)
+{
+ /* Address of boot parameters */
+ gd->bd->bi_boot_params = PHYS_SDRAM + 0x100;
+
+ return 0;
+}
+
+int board_late_init(void)
+{
+ imx_iomux_v3_setup_multiple_pads(wdog_pads, ARRAY_SIZE(wdog_pads));
+
+ return 0;
+}
+
+int checkboard(void)
+{
+ puts("Board: MX6SLL EVK\n");
+
+ return 0;
+}
+
+int board_mmc_get_env_dev(int devno)
+{
+ return devno;
+}
+
+int mmc_map_to_kernel_blk(int devno)
+{
+ return devno;
+}