powerpc/t1024rdb: Add T1024 RDB board support
T1024RDB is a Freescale Reference Design Board that hosts the T1024 SoC.
T1024RDB board Overview
-----------------------
- T1024 SoC integrating two 64-bit e5500 cores up to 1.4GHz
- CoreNet fabric supporting coherent and noncoherent transactions with
prioritization and bandwidth allocation
- 32-/64-bit DDR3L SDRAM memory controller with ECC and interleaving support
- Accelerator: DPAA components consist of FMan, BMan, QMan, DCE and SEC
- Ethernet interfaces:
- Two 10M/100M/1G RGMII ports on-board
- one 10Gbps XFI interface
- PCIe: Three PCIe controllers: one PCIe Slot and two Mini-PCIe connectors.
- SerDes: 4 lanes up to 10.3125GHz
- IFC: 128MB NOR Flash, 512MB NAND Flash and CPLD
- eSPI: 64MB N25Q512 SPI flash.
- Deep Sleep power implementaion (wakeup from GPIO/Timer/Ethernet/USB)
- USB: Two Type-A USB2.0 ports with internal PHY
- eSDHC: Support SD, SDHC, SDXC and MMC/eMMC
- I2C: Four I2C controllers
- UART: Two UART serial ports
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
[York Sun: Fix ft_board_setup() type, fix MAINTAINERS for SECURE_BOOT
Fix Kconfig by adding SUPPORT_SPL]
Reviewed-by: York Sun <yorksun@freescale.com>
diff --git a/board/freescale/t102xrdb/README b/board/freescale/t102xrdb/README
new file mode 100644
index 0000000..2b17f50
--- /dev/null
+++ b/board/freescale/t102xrdb/README
@@ -0,0 +1,258 @@
+T1024 SoC Overview
+------------------
+The T1024/T1023 dual core and T1014/T1013 single core QorIQ communication processor
+combines two or one 64-bit Power Architecture e5500 core respectively with high
+performance datapath acceleration logic, and network peripheral bus interfaces
+required for networking and telecommunications. This processor can be used in
+applications such as enterprise WLAN access points, routers, switches, firewall
+and other packet processing intensive small enterprise and branch office appliances,
+and general-purpose embedded computing. Its high level of integration offers
+significant performance benefits and greatly helps to simplify board design.
+
+
+The T1024 SoC includes the following function and features:
+- two e5500 cores, each with a private 256 KB L2 cache
+ - Up to 1.4 GHz with 64-bit ISA support (Power Architecture v2.06-compliant)
+ - Three levels of instructions: User, supervisor, and hypervisor
+ - Independent boot and reset
+ - Secure boot capability
+- 256 KB shared L3 CoreNet platform cache (CPC)
+- Interconnect CoreNet platform
+ - CoreNet coherency manager supporting coherent and noncoherent transactions
+ with prioritization and bandwidth allocation amongst CoreNet endpoints
+ - 150 Gbps coherent read bandwidth
+- 32-/64-bit DDR3L/DDR4 SDRAM memory controller with ECC and interleaving support
+- Data Path Acceleration Architecture (DPAA) incorporating acceleration for the following functions:
+ - Packet parsing, classification, and distribution
+ - Queue management for scheduling, packet sequencing, and congestion management
+ - Cryptography Acceleration (SEC 5.x)
+ - IEEE 1588 support
+ - Hardware buffer management for buffer allocation and deallocation
+ - MACSEC on DPAA-based Ethernet ports
+- Ethernet interfaces
+ - Four 1 Gbps Ethernet controllers
+- Parallel Ethernet interfaces
+ - Two RGMII interfaces
+- High speed peripheral interfaces
+ - Three PCI Express 2.0 controllers/ports running at up to 5 GHz
+ - One SATA controller supporting 1.5 and 3.0 Gb/s operation
+ - One QSGMII interface
+ - Four SGMII interface supporting 1000 Mbps
+ - Three SGMII interfaces supporting up to 2500 Mbps
+ - 10GbE XFI or 10Base-KR interface
+- Additional peripheral interfaces
+ - Two USB 2.0 controllers with integrated PHY
+ - SD/eSDHC/eMMC
+ - eSPI controller
+ - Four I2C controllers
+ - Four UARTs
+ - Four GPIO controllers
+ - Integrated flash controller (IFC)
+ - LCD interface (DIU) with 12 bit dual data rate
+- Multicore programmable interrupt controller (PIC)
+- Two 8-channel DMA engines
+- Single source clocking implementation
+- Deep Sleep power implementaion (wakeup from GPIO/Timer/Ethernet/USB)
+- QUICC Engine block
+ - 32-bit RISC controller for flexible support of the communications peripherals
+ - Serial DMA channel for receive and transmit on all serial channels
+ - Two universal communication controllers, supporting TDM, HDLC, and UART
+
+T1023 Personality
+------------------
+T1023 is a reduced personality of T1024 without QUICC Engine, DIU, and
+unavailable deep sleep. Rest of the blocks are almost same as T1024.
+Differences between T1024 and T1023
+Feature T1024 T1023
+QUICC Engine: yes no
+DIU: yes no
+Deep Sleep: yes no
+I2C controller: 4 3
+DDR: 64-bit 32-bit
+IFC: 32-bit 28-bit
+
+
+T1024RDB board Overview
+-----------------------
+ - Ethernet
+ - Two on-board 10M/100M/1G bps RGMII ethernet ports
+ - One on-board 10G bps Base-T port.
+ - DDR Memory
+ - Supports 64-bit 4GB DDR3L DIMM
+ - PCIe
+ - One on-board PCIe slot.
+ - Two on-board PCIe Mini-PCIe connectors.
+ - IFC/Local Bus
+ - NOR: 128MB 16-bit NOR Flash
+ - NAND: 1GB 8-bit NAND flash
+ - CPLD: for system controlling with programable header on-board
+ - USB
+ - Supports two USB 2.0 ports with integrated PHYs
+ - Two type A ports with 5V@1.5A per port.
+ - SDHC
+ - one SD connector supporting 1.8V/3.3V via J53.
+ - SPI
+ - On-board 64MB SPI flash
+ - Other
+ - Two Serial ports
+ - Four I2C ports
+
+
+Memory map on T1024RDB
+----------------------
+Start Address End Address Description Size
+0xF_FFDF_0000 0xF_FFDF_0FFF IFC - CPLD 4KB
+0xF_FF80_0000 0xF_FF80_FFFF IFC - NAND Flash 64KB
+0xF_FE00_0000 0xF_FEFF_FFFF CCSRBAR 16MB
+0xF_F802_0000 0xF_F802_FFFF PCI Express 3 I/O Space 64KB
+0xF_F801_0000 0xF_F801_FFFF PCI Express 2 I/O Space 64KB
+0xF_F800_0000 0xF_F800_FFFF PCI Express 1 I/O Space 64KB
+0xF_F600_0000 0xF_F7FF_FFFF Queue manager software portal 32MB
+0xF_F400_0000 0xF_F5FF_FFFF Buffer manager software portal 32MB
+0xF_E800_0000 0xF_EFFF_FFFF IFC - NOR Flash 128MB
+0xF_0000_0000 0xF_003F_FFFF DCSR 4MB
+0xC_2000_0000 0xC_2FFF_FFFF PCI Express 3 Mem Space 256MB
+0xC_1000_0000 0xC_1FFF_FFFF PCI Express 2 Mem Space 256MB
+0xC_0000_0000 0xC_0FFF_FFFF PCI Express 1 Mem Space 256MB
+0x0_0000_0000 0x0_ffff_ffff DDR 4GB
+
+
+128MB NOR Flash memory Map
+--------------------------
+Start Address End Address Definition Max size
+0xEFF40000 0xEFFFFFFF u-boot (current bank) 768KB
+0xEFF20000 0xEFF3FFFF u-boot env (current bank) 128KB
+0xEFF00000 0xEFF1FFFF FMAN Ucode (current bank) 128KB
+0xEFE00000 0xEFE3FFFF QE firmware (current bank) 256KB
+0xED300000 0xEFEFFFFF rootfs (alt bank) 44MB
+0xEC800000 0xEC8FFFFF Hardware device tree (alt bank) 1MB
+0xEC020000 0xEC7FFFFF Linux.uImage (alt bank) 7MB + 875KB
+0xEC000000 0xEC01FFFF RCW (alt bank) 128KB
+0xEBF40000 0xEBFFFFFF u-boot (alt bank) 768KB
+0xEBF20000 0xEBF3FFFF u-boot env (alt bank) 128KB
+0xEBF00000 0xEBF1FFFF FMAN ucode (alt bank) 128KB
+0xEBE00000 0xEBE3FFFF QE firmware (alt bank) 256KB
+0xE9300000 0xEBEFFFFF rootfs (current bank) 44MB
+0xE8800000 0xE88FFFFF Hardware device tree (cur bank) 1MB
+0xE8020000 0xE86FFFFF Linux.uImage (current bank) 7MB + 875KB
+0xE8000000 0xE801FFFF RCW (current bank) 128KB
+
+
+T1024 Clock frequency
+---------------------
+BIN Core DDR Platform FMan
+Bin1: 1400MHz 1600MT/s 400MHz 700MHz
+Bin2: 1200MHz 1600MT/s 400MHz 600MHz
+Bin3: 1000MHz 1600MT/s 400MHz 500MHz
+
+
+Software configurations and board settings
+------------------------------------------
+1. NOR boot:
+ a. build NOR boot image
+ $ make T1024RDB_defconfig
+ $ make
+ b. program u-boot.bin image to NOR flash
+ => tftp 1000000 u-boot.bin
+ => pro off all;era eff40000 efffffff;cp.b 1000000 eff40000 $filesize
+ set SW1[1:8] = '00010011', SW2[1] = '1', SW3[4] = '0' for NOR boot
+
+ Switching between default bank0 and alternate bank4 on NOR flash
+ To change boot source to vbank4:
+ via software: run command 'cpld reset altbank' in u-boot.
+ via DIP-switch: set SW3[5:7] = '100'
+
+ To change boot source to vbank0:
+ via software: run command 'cpld reset' in u-boot.
+ via DIP-Switch: set SW3[5:7] = '000'
+
+2. NAND Boot:
+ a. build PBL image for NAND boot
+ $ make T1024RDB_NAND_defconfig
+ $ make
+ b. program u-boot-with-spl-pbl.bin to NAND flash
+ => tftp 1000000 u-boot-with-spl-pbl.bin
+ => nand erase 0 $filesize
+ => nand write 1000000 0 $filesize
+ set SW1[1:8] = '10001000', SW2[1] = '1', SW3[4] = '1' for NAND boot
+
+3. SPI Boot:
+ a. build PBL image for SPI boot
+ $ make T1024RDB_SPIFLASH_defconfig
+ $ make
+ b. program u-boot-with-spl-pbl.bin to SPI flash
+ => tftp 1000000 u-boot-with-spl-pbl.bin
+ => sf probe 0
+ => sf erase 0 f0000
+ => sf write 1000000 0 $filesize
+ set SW1[1:8] = '00100010', SW2[1] ='1' for SPI boot
+
+4. SD Boot:
+ a. build PBL image for SD boot
+ $ make T1024RDB_SDCARD_defconfig
+ $ make
+ b. program u-boot-with-spl-pbl.bin to SD/MMC card
+ => tftp 1000000 u-boot-with-spl-pbl.bin
+ => mmc write 1000000 8 0x800
+ => tftp 1000000 fsl_fman_ucode_t1024_xx.bin
+ => mmc write 1000000 0x820 80
+ set SW1[1:8] = '00100000', SW2[1] = '0' for SD boot
+
+
+2-stage NAND/SPI/SD boot loader
+-------------------------------
+PBL initializes the internal CPC-SRAM and copy SPL(160K) to SRAM.
+SPL further initializes DDR using SPD and environment variables
+and copy u-boot(768 KB) from NAND/SPI/SD device to DDR.
+Finally SPL transers control to u-boot for futher booting.
+
+SPL has following features:
+ - Executes within 256K
+ - No relocation required
+
+Run time view of SPL framework
+-------------------------------------------------
+|Area | Address |
+-------------------------------------------------
+|SecureBoot header | 0xFFFC0000 (32KB) |
+-------------------------------------------------
+|GD, BD | 0xFFFC8000 (4KB) |
+-------------------------------------------------
+|ENV | 0xFFFC9000 (8KB) |
+-------------------------------------------------
+|HEAP | 0xFFFCB000 (30KB) |
+-------------------------------------------------
+|STACK | 0xFFFD8000 (22KB) |
+-------------------------------------------------
+|U-boot SPL | 0xFFFD8000 (160KB) |
+-------------------------------------------------
+
+NAND Flash memory Map on T1024RDB
+-------------------------------------------------------------
+Start End Definition Size
+0x000000 0x0FFFFF u-boot 1MB(2 block)
+0x100000 0x17FFFF u-boot env 512KB(1 block)
+0x180000 0x1FFFFF FMAN Ucode 512KB(1 block)
+0x200000 0x27FFFF QE Firmware 512KB(1 block)
+
+
+SD Card memory Map on T1024RDB
+----------------------------------------------------
+Block #blocks Definition Size
+0x008 2048 u-boot img 1MB
+0x800 0016 u-boot env 8KB
+0x820 0256 FMAN Ucode 128KB
+0x920 0256 QE Firmware 128KB
+
+
+SPI Flash memory Map on T1024RDB
+----------------------------------------------------
+Start End Definition Size
+0x000000 0x0FFFFF u-boot img 1MB
+0x100000 0x101FFF u-boot env 8KB
+0x110000 0x12FFFF FMAN Ucode 128KB
+0x130000 0x14FFFF QE Firmware 128KB
+
+
+For more details, please refer to T1024RDB Reference Manual and access
+website www.freescale.com and Freescale QorIQ SDK Infocenter document.