ppc4xx: Unify AMCC's board config files (part 2/3)
This patch series unifies the AMCC eval board ports by introducing
a common include header for all AMCC eval boards:
include/configs/amcc-common.h
This header now includes all common configuration options/defines which
are removed from the board specific headers.
The reason for this is ease of maintenance and unified look and feel
of all AMCC boards.
Signed-off-by: Stefan Roese <sr@denx.de>
diff --git a/include/configs/kilauea.h b/include/configs/kilauea.h
index 205577f..9c1a3a4 100644
--- a/include/configs/kilauea.h
+++ b/include/configs/kilauea.h
@@ -39,6 +39,12 @@
#define CONFIG_405EX 1 /* Specifc 405EX support*/
#define CONFIG_SYS_CLK_FREQ 33333333 /* ext frequency to pll */
+/*
+ * Include common defines/options for all AMCC eval boards
+ */
+#define CONFIG_HOSTNAME kilauea
+#include "amcc-common.h"
+
#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */
#define CONFIG_MISC_INIT_R 1 /* Call misc_init_r */
#define CONFIG_BOARD_EMAC_COUNT
@@ -47,14 +53,10 @@
* Base addresses -- Note these are effective addresses where the
* actual resources get mapped (not physical addresses)
*----------------------------------------------------------------------*/
-#define CFG_SDRAM_BASE 0x00000000
#define CFG_FLASH_BASE 0xFC000000
#define CFG_NAND_ADDR 0xF8000000
#define CFG_FPGA_BASE 0xF0000000
#define CFG_PERIPHERAL_BASE 0xEF600000 /* internal peripherals*/
-#define CFG_MONITOR_LEN (384 * 1024) /* Reserve 384 kB for Monitor */
-#define CFG_MALLOC_LEN (512 * 1024) /* Reserve 512 kB for malloc() */
-#define CFG_MONITOR_BASE (TEXT_BASE)
/*-----------------------------------------------------------------------
* Initial RAM & Stack Pointer Configuration Options
@@ -112,14 +114,9 @@
* Serial Port
*----------------------------------------------------------------------*/
#define CFG_EXT_SERIAL_CLOCK 11059200 /* ext. 11.059MHz clk */
-#define CONFIG_BAUDRATE 115200
-#define CONFIG_SERIAL_MULTI 1
/* define this if you want console on UART1 */
#undef CONFIG_UART1_CONSOLE
-#define CFG_BAUDRATE_TABLE \
- {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
-
/*-----------------------------------------------------------------------
* Environment
*----------------------------------------------------------------------*/
@@ -273,9 +270,7 @@
/*-----------------------------------------------------------------------
* I2C
*----------------------------------------------------------------------*/
-#define CONFIG_HARD_I2C 1 /* I2C with hardware support */
#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */
-#define CFG_I2C_SLAVE 0x7F
#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 6 /* 24C02 requires 5ms delay */
#define CFG_I2C_EEPROM_ADDR 0x52 /* I2C boot EEPROM (24C02BN) */
@@ -295,7 +290,6 @@
*----------------------------------------------------------------------*/
#define CONFIG_M88E1111_PHY 1
#define CONFIG_IBM_EMAC4_V4 1
-#define CONFIG_MII 1 /* MII PHY management */
#define CONFIG_PHY_ADDR 1 /* PHY address, See schematics */
#define CONFIG_PHY_RESET 1 /* reset phy upon startup */
@@ -303,102 +297,33 @@
#define CONFIG_HAS_ETH0 1
-#define CONFIG_NET_MULTI 1
#define CONFIG_HAS_ETH1 1 /* add support for "eth1addr" */
#define CONFIG_PHY1_ADDR 2
-#define CFG_RX_ETH_BUFFER 32 /* Number of ethernet rx buffers & descriptors */
-
-#define CONFIG_PREBOOT "echo;" \
- "echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \
- "echo"
-
-#undef CONFIG_BOOTARGS
-
+/*
+ * Default environment variables
+ */
#define CONFIG_EXTRA_ENV_SETTINGS \
+ CONFIG_AMCC_DEF_ENV \
+ CONFIG_AMCC_DEF_ENV_POWERPC \
+ CONFIG_AMCC_DEF_ENV_PPC_OLD \
+ CONFIG_AMCC_DEF_ENV_NOR_UPD \
+ CONFIG_AMCC_DEF_ENV_NAND_UPD \
"logversion=2\0" \
- "netdev=eth0\0" \
- "hostname=kilauea\0" \
- "nfsargs=setenv bootargs root=/dev/nfs rw " \
- "nfsroot=${serverip}:${rootpath}\0" \
- "ramargs=setenv bootargs root=/dev/ram rw\0" \
- "addip=setenv bootargs ${bootargs} " \
- "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \
- ":${hostname}:${netdev}:off panic=1\0" \
- "addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\
- "flash_self_old=run ramargs addip addtty;" \
- "bootm ${kernel_addr} ${ramdisk_addr}\0" \
- "flash_self=run ramargs addip addtty;" \
- "bootm ${kernel_addr} ${ramdisk_addr} ${fdt_addr}\0" \
- "flash_nfs_old=run nfsargs addip addtty;" \
- "bootm ${kernel_addr}\0" \
- "flash_nfs=run nfsargs addip addtty;" \
- "bootm ${kernel_addr} - ${fdt_addr}\0" \
- "net_nfs_old=tftp ${kernel_addr_r} ${bootfile};" \
- "run nfsargs addip addtty;bootm ${kernel_addr_r}\0" \
- "net_nfs=tftp ${kernel_addr_r} ${bootfile}; " \
- "tftp ${fdt_addr_r} ${fdt_file}; " \
- "run nfsargs addip addtty;" \
- "bootm ${kernel_addr_r} - ${fdt_addr_r}\0" \
- "rootpath=/opt/eldk/ppc_4xx\0" \
- "bootfile=kilauea/uImage\0" \
- "fdt_file=kilauea/kilauea.dtb\0" \
- "kernel_addr_r=400000\0" \
- "fdt_addr_r=800000\0" \
"kernel_addr=fc000000\0" \
"fdt_addr=fc1e0000\0" \
"ramdisk_addr=fc200000\0" \
- "initrd_high=30000000\0" \
- "load=tftp 200000 kilauea/u-boot.bin\0" \
- "update=protect off fffa0000 ffffffff;era fffa0000 ffffffff;" \
- "cp.b ${fileaddr} fffa0000 ${filesize};" \
- "setenv filesize;saveenv\0" \
- "upd=run load update\0" \
- "nload=tftp 200000 kilauea/u-boot-nand.bin\0" \
- "nupdate=nand erase 0 60000;nand write 200000 0 60000;" \
- "setenv filesize;saveenv\0" \
- "nupd=run nload nupdate\0" \
"pciconfighost=1\0" \
"pcie_mode=RP:RP\0" \
""
-#define CONFIG_BOOTCOMMAND "run flash_self"
-
-#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */
-
-#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
-#define CFG_LOADS_BAUD_CHANGE /* allow baudrate change */
/*
- * BOOTP options
+ * Commands additional to the ones defined in amcc-common.h
*/
-#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-#define CONFIG_BOOTP_SUBNETMASK
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_ASKENV
#define CONFIG_CMD_DATE
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_DIAG
-#define CONFIG_CMD_DTT
-#define CONFIG_CMD_EEPROM
-#define CONFIG_CMD_ELF
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_IRQ
#define CONFIG_CMD_LOG
-#define CONFIG_CMD_MII
#define CONFIG_CMD_NAND
-#define CONFIG_CMD_NET
-#define CONFIG_CMD_NFS
#define CONFIG_CMD_PCI
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_REGINFO
#define CONFIG_CMD_SNTP
/* POST support */
@@ -417,37 +342,6 @@
#define CFG_CONSOLE_IS_IN_ENV /* Otherwise it catches logbuffer as output */
-#undef CONFIG_WATCHDOG /* watchdog disabled */
-
-/*-----------------------------------------------------------------------
- * Miscellaneous configurable options
- *----------------------------------------------------------------------*/
-#define CFG_LONGHELP /* undef to save memory */
-#define CFG_PROMPT "=> " /* Monitor Command Prompt */
-#if defined(CONFIG_CMD_KGDB)
-#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
-#else
-#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
-#endif
-#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
-#define CFG_MAXARGS 16 /* max number of command args */
-#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
-
-#define CFG_MEMTEST_START 0x0400000 /* memtest works on */
-#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
-
-#define CFG_LOAD_ADDR 0x100000 /* default load address */
-#define CFG_EXTBDINFO 1 /* To use extended board_into (bd_t) */
-
-#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
-
-#define CONFIG_CMDLINE_EDITING 1 /* add command line history */
-#define CONFIG_LOOPW 1 /* enable loopw command */
-#define CONFIG_MX_CYCLIC 1 /* enable mdc/mwc commands */
-#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */
-#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */
-#define CFG_CONSOLE_INFO_QUIET 1 /* don't print console @ startup*/
-
/*-----------------------------------------------------------------------
* PCI stuff
*----------------------------------------------------------------------*/
@@ -476,13 +370,6 @@
/* base address of inbound PCIe window */
#define CFG_PCIE_INBOUND_BASE 0x0000000000000000ULL
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
-
/*-----------------------------------------------------------------------
* External Bus Controller (EBC) Setup
*----------------------------------------------------------------------*/
@@ -556,19 +443,6 @@
} \
}
-/*
- * Internal Definitions
- *
- * Boot Flags
- */
-#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
-#define BOOTFLAG_WARM 0x02 /* Software reboot */
-
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
-#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
-#endif
-
/*-----------------------------------------------------------------------
* Some Kilauea stuff..., mainly fpga registers
*/
@@ -604,8 +478,4 @@
#define CFG_FPGA_USER_LED0 0x00000200
#define CFG_FPGA_USER_LED1 0x00000100
-/* pass open firmware flat tree */
-#define CONFIG_OF_LIBFDT 1
-#define CONFIG_OF_BOARD_SETUP 1
-
#endif /* __CONFIG_H */