ARM: dts: omap3-devkit8000: Add support for Devkit8000
This commit adds OMAP3 BeagleBoard devicetree files from Linux
v5.16.0.
This commit fixes CONFIG_DM_MMC warning.
v3: patch clean-up
Signed-off-by: Anthoine Bourgeois <anthoine.bourgeois@gmail.com>
diff --git a/arch/arm/dts/omap3-devkit8000.dts b/arch/arm/dts/omap3-devkit8000.dts
new file mode 100644
index 0000000..eee3ba0
--- /dev/null
+++ b/arch/arm/dts/omap3-devkit8000.dts
@@ -0,0 +1,349 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Author: Anthoine Bourgeois <anthoine.bourgeois@gmail.com>
+ */
+/dts-v1/;
+
+#include "omap34xx.dtsi"
+/ {
+ model = "TimLL OMAP3 Devkit8000";
+ compatible = "timll,omap3-devkit8000", "ti,omap3430", "ti,omap3";
+
+ aliases {
+ display1 = &dvi0;
+ display2 = &tv0;
+ };
+
+ memory@80000000 {
+ device_type = "memory";
+ reg = <0x80000000 0x10000000>; /* 256 MB */
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ heartbeat {
+ label = "devkit8000::led1";
+ gpios = <&gpio6 26 GPIO_ACTIVE_HIGH>; /* 186 -> LED1 */
+ default-state = "on";
+ linux,default-trigger = "heartbeat";
+ };
+
+ mmc {
+ label = "devkit8000::led2";
+ gpios = <&gpio6 3 GPIO_ACTIVE_HIGH>; /* 163 -> LED2 */
+ default-state = "on";
+ linux,default-trigger = "none";
+ };
+
+ usr {
+ label = "devkit8000::led3";
+ gpios = <&gpio6 4 GPIO_ACTIVE_HIGH>; /* 164 -> LED3 */
+ default-state = "on";
+ linux,default-trigger = "usr";
+ };
+
+ pmu_stat {
+ label = "devkit8000::pmu_stat";
+ gpios = <&twl_gpio 19 GPIO_ACTIVE_HIGH>; /* LEDB */
+ };
+ };
+
+ sound {
+ compatible = "ti,omap-twl4030";
+ ti,model = "devkit8000";
+
+ ti,mcbsp = <&mcbsp2>;
+ ti,audio-routing =
+ "Ext Spk", "PREDRIVEL",
+ "Ext Spk", "PREDRIVER",
+ "MAINMIC", "Main Mic",
+ "Main Mic", "Mic Bias 1";
+ };
+
+ tfp410: encoder0 {
+ compatible = "ti,tfp410";
+ powerdown-gpios = <&twl_gpio 7 GPIO_ACTIVE_LOW>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+
+ tfp410_in: endpoint {
+ remote-endpoint = <&dpi_dvi_out>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+
+ tfp410_out: endpoint {
+ remote-endpoint = <&dvi_connector_in>;
+ };
+ };
+ };
+ };
+
+ dvi0: connector0 {
+ compatible = "dvi-connector";
+ label = "dvi";
+
+ digital;
+
+ ddc-i2c-bus = <&i2c2>;
+
+ port {
+ dvi_connector_in: endpoint {
+ remote-endpoint = <&tfp410_out>;
+ };
+ };
+ };
+
+ tv0: connector1 {
+ compatible = "svideo-connector";
+ label = "tv";
+
+ port {
+ tv_connector_in: endpoint {
+ remote-endpoint = <&venc_out>;
+ };
+ };
+ };
+};
+
+&i2c1 {
+ clock-frequency = <2600000>;
+
+ twl: twl@48 {
+ reg = <0x48>;
+ interrupts = <7>; /* SYS_NIRQ cascaded to intc */
+
+ twl_audio: audio {
+ compatible = "ti,twl4030-audio";
+ codec {
+ };
+ };
+ };
+};
+
+&i2c2 {
+ clock-frequency = <400000>;
+};
+
+&i2c3 {
+ status = "disabled";
+};
+
+#include "twl4030.dtsi"
+#include "twl4030_omap3.dtsi"
+
+&mmc1 {
+ vmmc-supply = <&vmmc1>;
+ vqmmc-supply = <&vsim>;
+ bus-width = <8>;
+};
+
+&mmc2 {
+ status = "disabled";
+};
+
+&mmc3 {
+ status = "disabled";
+};
+
+&twl_gpio {
+ ti,use-leds;
+ /*
+ * pulldowns:
+ * BIT(1), BIT(2), BIT(6), BIT(7), BIT(8), BIT(13)
+ * BIT(15), BIT(16), BIT(17)
+ */
+ ti,pulldowns = <0x03a1c6>;
+};
+
+&wdt2 {
+ status = "disabled";
+};
+
+&mcbsp2 {
+ status = "okay";
+};
+
+&gpmc {
+ ranges = <0 0 0x30000000 0x1000000 /* CS0: 16MB for NAND */
+ 6 0 0x2c000000 0x1000000>; /* CS6: 16MB for DM9000 */
+
+ nand@0,0 {
+ compatible = "ti,omap2-nand";
+ reg = <0 0 4>; /* CS0, offset 0, IO size 4 */
+ interrupt-parent = <&gpmc>;
+ interrupts = <0 IRQ_TYPE_NONE>, /* fifoevent */
+ <1 IRQ_TYPE_NONE>; /* termcount */
+ nand-bus-width = <16>;
+ gpmc,device-width = <2>;
+ ti,nand-ecc-opt = "sw";
+
+ gpmc,sync-clk-ps = <0>;
+ gpmc,cs-on-ns = <0>;
+ gpmc,cs-rd-off-ns = <44>;
+ gpmc,cs-wr-off-ns = <44>;
+ gpmc,adv-on-ns = <6>;
+ gpmc,adv-rd-off-ns = <34>;
+ gpmc,adv-wr-off-ns = <44>;
+ gpmc,we-off-ns = <40>;
+ gpmc,oe-off-ns = <54>;
+ gpmc,access-ns = <64>;
+ gpmc,rd-cycle-ns = <82>;
+ gpmc,wr-cycle-ns = <82>;
+ gpmc,wr-access-ns = <40>;
+ gpmc,wr-data-mux-bus-ns = <0>;
+
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ x-loader@0 {
+ label = "X-Loader";
+ reg = <0 0x80000>;
+ };
+
+ bootloaders@80000 {
+ label = "U-Boot";
+ reg = <0x80000 0x1e0000>;
+ };
+
+ bootloaders_env@260000 {
+ label = "U-Boot Env";
+ reg = <0x260000 0x20000>;
+ };
+
+ kernel@280000 {
+ label = "Kernel";
+ reg = <0x280000 0x400000>;
+ };
+
+ filesystem@680000 {
+ label = "File System";
+ reg = <0x680000 0xf980000>;
+ };
+ };
+
+ ethernet@6,0 {
+ compatible = "davicom,dm9000";
+ reg = <6 0x000 2
+ 6 0x400 2>; /* CS6, offset 0 and 0x400, IO size 2 */
+ bank-width = <2>;
+ interrupt-parent = <&gpio1>;
+ interrupts = <25 IRQ_TYPE_LEVEL_LOW>;
+ davicom,no-eeprom;
+
+ gpmc,mux-add-data = <0>;
+ gpmc,device-width = <1>;
+ gpmc,wait-pin = <0>;
+ gpmc,cycle2cycle-samecsen;
+ gpmc,cycle2cycle-diffcsen;
+
+ gpmc,cs-on-ns = <6>;
+ gpmc,cs-rd-off-ns = <180>;
+ gpmc,cs-wr-off-ns = <180>;
+ gpmc,adv-on-ns = <0>;
+ gpmc,adv-rd-off-ns = <18>;
+ gpmc,adv-wr-off-ns = <48>;
+ gpmc,oe-on-ns = <54>;
+ gpmc,oe-off-ns = <168>;
+ gpmc,we-on-ns = <54>;
+ gpmc,we-off-ns = <168>;
+ gpmc,rd-cycle-ns = <186>;
+ gpmc,wr-cycle-ns = <186>;
+ gpmc,access-ns = <144>;
+ gpmc,page-burst-access-ns = <24>;
+ gpmc,bus-turnaround-ns = <90>;
+ gpmc,cycle2cycle-delay-ns = <90>;
+ gpmc,wait-monitoring-ns = <0>;
+ gpmc,clk-activation-ns = <0>;
+ gpmc,wr-data-mux-bus-ns = <0>;
+ gpmc,wr-access-ns = <0>;
+ };
+};
+
+&omap3_pmx_core {
+ dss_dpi_pins: pinmux_dss_dpi_pins {
+ pinctrl-single,pins = <
+ OMAP3_CORE1_IOPAD(0x20d4, PIN_OUTPUT | MUX_MODE0) /* dss_pclk.dss_pclk */
+ OMAP3_CORE1_IOPAD(0x20d6, PIN_OUTPUT | MUX_MODE0) /* dss_hsync.dss_hsync */
+ OMAP3_CORE1_IOPAD(0x20d8, PIN_OUTPUT | MUX_MODE0) /* dss_vsync.dss_vsync */
+ OMAP3_CORE1_IOPAD(0x20da, PIN_OUTPUT | MUX_MODE0) /* dss_acbias.dss_acbias */
+ OMAP3_CORE1_IOPAD(0x20dc, PIN_OUTPUT | MUX_MODE0) /* dss_data0.dss_data0 */
+ OMAP3_CORE1_IOPAD(0x20de, PIN_OUTPUT | MUX_MODE0) /* dss_data1.dss_data1 */
+ OMAP3_CORE1_IOPAD(0x20e0, PIN_OUTPUT | MUX_MODE0) /* dss_data2.dss_data2 */
+ OMAP3_CORE1_IOPAD(0x20e2, PIN_OUTPUT | MUX_MODE0) /* dss_data3.dss_data3 */
+ OMAP3_CORE1_IOPAD(0x20e4, PIN_OUTPUT | MUX_MODE0) /* dss_data4.dss_data4 */
+ OMAP3_CORE1_IOPAD(0x20e6, PIN_OUTPUT | MUX_MODE0) /* dss_data5.dss_data5 */
+ OMAP3_CORE1_IOPAD(0x20e8, PIN_OUTPUT | MUX_MODE0) /* dss_data6.dss_data6 */
+ OMAP3_CORE1_IOPAD(0x20ea, PIN_OUTPUT | MUX_MODE0) /* dss_data7.dss_data7 */
+ OMAP3_CORE1_IOPAD(0x20ec, PIN_OUTPUT | MUX_MODE0) /* dss_data8.dss_data8 */
+ OMAP3_CORE1_IOPAD(0x20ee, PIN_OUTPUT | MUX_MODE0) /* dss_data9.dss_data9 */
+ OMAP3_CORE1_IOPAD(0x20f0, PIN_OUTPUT | MUX_MODE0) /* dss_data10.dss_data10 */
+ OMAP3_CORE1_IOPAD(0x20f2, PIN_OUTPUT | MUX_MODE0) /* dss_data11.dss_data11 */
+ OMAP3_CORE1_IOPAD(0x20f4, PIN_OUTPUT | MUX_MODE0) /* dss_data12.dss_data12 */
+ OMAP3_CORE1_IOPAD(0x20f6, PIN_OUTPUT | MUX_MODE0) /* dss_data13.dss_data13 */
+ OMAP3_CORE1_IOPAD(0x20f8, PIN_OUTPUT | MUX_MODE0) /* dss_data14.dss_data14 */
+ OMAP3_CORE1_IOPAD(0x20fa, PIN_OUTPUT | MUX_MODE0) /* dss_data15.dss_data15 */
+ OMAP3_CORE1_IOPAD(0x20fc, PIN_OUTPUT | MUX_MODE0) /* dss_data16.dss_data16 */
+ OMAP3_CORE1_IOPAD(0x20fe, PIN_OUTPUT | MUX_MODE0) /* dss_data17.dss_data17 */
+ OMAP3_CORE1_IOPAD(0x2100, PIN_OUTPUT | MUX_MODE0) /* dss_data18.dss_data18 */
+ OMAP3_CORE1_IOPAD(0x2102, PIN_OUTPUT | MUX_MODE0) /* dss_data19.dss_data19 */
+ OMAP3_CORE1_IOPAD(0x2104, PIN_OUTPUT | MUX_MODE0) /* dss_data20.dss_data20 */
+ OMAP3_CORE1_IOPAD(0x2106, PIN_OUTPUT | MUX_MODE0) /* dss_data21.dss_data21 */
+ OMAP3_CORE1_IOPAD(0x2108, PIN_OUTPUT | MUX_MODE0) /* dss_data22.dss_data22 */
+ OMAP3_CORE1_IOPAD(0x210a, PIN_OUTPUT | MUX_MODE0) /* dss_data23.dss_data23 */
+ >;
+ };
+};
+
+&vpll1 {
+ /* Needed for DSS */
+ regulator-name = "vdds_dsi";
+
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+};
+
+&dss {
+ status = "okay";
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&dss_dpi_pins>;
+
+ vdds_dsi-supply = <&vpll1>;
+ vdda_dac-supply = <&vdac>;
+
+ port {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ dpi_dvi_out: endpoint@0 {
+ reg = <0>;
+ remote-endpoint = <&tfp410_in>;
+ data-lines = <24>;
+ };
+
+ endpoint@1 {
+ reg = <1>;
+ };
+ };
+};
+
+&venc {
+ status = "okay";
+
+ vdda-supply = <&vdac>;
+
+ port {
+ venc_out: endpoint {
+ remote-endpoint = <&tv_connector_in>;
+ ti,channels = <2>;
+ };
+ };
+};