Initial revision
diff --git a/cpu/74xx_7xx/cpu_init.c b/cpu/74xx_7xx/cpu_init.c
new file mode 100644
index 0000000..2843e26
--- /dev/null
+++ b/cpu/74xx_7xx/cpu_init.c
@@ -0,0 +1,54 @@
+/*
+ * (C) Copyright 2001
+ * Josh Huber <huber@mclx.com>, Mission Critical Linux, Inc.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+/*
+ * cpu_init.c - low level cpu init
+ *
+ * there's really nothing going on here yet. future work area?
+ */
+
+#include <common.h>
+#include <74xx_7xx.h>
+
+/*
+ * Breath some life into the CPU...
+ *
+ * there's basically nothing to do here since the memory controller
+ * isn't on the CPU in this case.
+ */
+void
+cpu_init_f (void)
+{
+ if (get_cpu_type() == CPU_7450) {
+ /* enable the timebase bit in HID0 */
+ set_hid0(get_hid0() | 0x4000000);
+ }
+}
+
+/*
+ * initialize higher level parts of CPU like timers
+ */
+int cpu_init_r (void)
+{
+ return (0);
+}
diff --git a/cpu/74xx_7xx/speed.c b/cpu/74xx_7xx/speed.c
new file mode 100644
index 0000000..fe553f1
--- /dev/null
+++ b/cpu/74xx_7xx/speed.c
@@ -0,0 +1,76 @@
+/*
+ * (C) Copyright 2000-2002
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <74xx_7xx.h>
+#include <asm/processor.h>
+
+static const int hid1_multipliers_x_10[] = {
+ 25, /* 0000 - 2.5x */
+ 75, /* 0001 - 7.5x */
+ 70, /* 0010 - 7x */
+ 10, /* 0011 - bypass */
+ 20, /* 0100 - 2x */
+ 65, /* 0101 - 6.5x */
+ 100, /* 0110 - 10x */
+ 45, /* 0111 - 4.5x */
+ 30, /* 1000 - 3x */
+ 55, /* 1001 - 5.5x */
+ 40, /* 1010 - 4x */
+ 50, /* 1011 - 5x */
+ 80, /* 1100 - 8x */
+ 60, /* 1101 - 6x */
+ 35, /* 1110 - 3.5x */
+ 0 /* 1111 - off */
+};
+
+/* ------------------------------------------------------------------------- */
+
+/*
+ * Measure CPU clock speed (core clock GCLK1, GCLK2)
+ *
+ * (Approx. GCLK frequency in Hz)
+ */
+
+int get_clocks (void)
+{
+ DECLARE_GLOBAL_DATA_PTR;
+
+ ulong clock = CFG_BUS_CLK * \
+ hid1_multipliers_x_10[get_hid1 () >> 28] / 10;
+ gd->cpu_clk = clock;
+ gd->bus_clk = CFG_BUS_CLK;
+
+ return (0);
+}
+
+/* ------------------------------------------------------------------------- */
+
+#if 0 /* disabled XXX - use global data instead */
+ulong get_bus_freq (ulong gclk_freq)
+{
+ return CFG_BUS_CLK;
+}
+#endif /* 0 */
+
+/* ------------------------------------------------------------------------- */
diff --git a/cpu/mpc824x/cpu.c b/cpu/mpc824x/cpu.c
new file mode 100644
index 0000000..0d822d5
--- /dev/null
+++ b/cpu/mpc824x/cpu.c
@@ -0,0 +1,281 @@
+/*
+ * (C) Copyright 2000 - 2002
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <config.h>
+#include <mpc824x.h>
+#include <common.h>
+#include <command.h>
+
+int checkcpu (void)
+{
+ DECLARE_GLOBAL_DATA_PTR;
+
+ unsigned int pvr = get_pvr ();
+ unsigned int version = pvr >> 16;
+ unsigned char revision;
+ ulong clock = gd->cpu_clk;
+ char buf[32];
+
+ puts ("CPU: ");
+
+ switch (version) {
+ case CPU_TYPE_8240:
+ puts ("MPC8240");
+ break;
+
+ case CPU_TYPE_8245:
+ puts ("MPC8245");
+ break;
+
+ default:
+ return -1; /*not valid for this source */
+ }
+
+ CONFIG_READ_BYTE (REVID, revision);
+
+ if (revision) {
+ printf (" Revision %d.%d",
+ (revision & 0xf0) >> 4,
+ (revision & 0x0f));
+ } else {
+ return -1; /* no valid CPU revision info */
+ }
+
+ printf (" at %s MHz:", strmhz (buf, clock));
+
+ printf (" %u kB I-Cache", checkicache () >> 10);
+ printf (" %u kB D-Cache", checkdcache () >> 10);
+
+ puts ("\n");
+
+ return 0;
+}
+
+/* ------------------------------------------------------------------------- */
+/* L1 i-cache */
+
+int checkicache (void)
+{
+ /*TODO*/
+ return 128 * 4 * 32;
+};
+
+/* ------------------------------------------------------------------------- */
+/* L1 d-cache */
+
+int checkdcache (void)
+{
+ /*TODO*/
+ return 128 * 4 * 32;
+
+};
+
+/*------------------------------------------------------------------- */
+
+int do_reset (cmd_tbl_t * cmdtp, bd_t * bd, int flag, int argc,
+ char *argv[])
+{
+ ulong msr, addr;
+
+ /* Interrupts and MMU off */
+ __asm__ ("mtspr 81, 0");
+
+ /* Interrupts and MMU off */
+ __asm__ __volatile__ ("mfmsr %0":"=r" (msr):);
+
+ msr &= ~0x1030;
+ __asm__ __volatile__ ("mtmsr %0"::"r" (msr));
+
+ /*
+ * Trying to execute the next instruction at a non-existing address
+ * should cause a machine check, resulting in reset
+ */
+#ifdef CFG_RESET_ADDRESS
+ addr = CFG_RESET_ADDRESS;
+#else
+ /*
+ * note: when CFG_MONITOR_BASE points to a RAM address,
+ * CFG_MONITOR_BASE - sizeof (ulong) is usually a valid
+ * address. Better pick an address known to be invalid on
+ * your system and assign it to CFG_RESET_ADDRESS.
+ * "(ulong)-1" used to be a good choice for many systems...
+ */
+ addr = CFG_MONITOR_BASE - sizeof (ulong);
+#endif
+ ((void (*)(void)) addr) ();
+ return 1;
+
+}
+
+/* ------------------------------------------------------------------------- */
+
+/*
+ * Get timebase clock frequency (like cpu_clk in Hz)
+ * This is the sys_logic_clk (memory bus) divided by 4
+ */
+unsigned long get_tbclk (void)
+{
+ return ((get_bus_freq (0) + 2L) / 4L);
+}
+
+/* ------------------------------------------------------------------------- */
+
+/*
+ * The MPC824x has an integrated PCI controller known as the MPC107.
+ * The following are MPC107 Bridge Controller and PCI Support functions
+ *
+ */
+
+/*
+ * This procedure reads a 32-bit address MPC107 register, and returns
+ * a 32 bit value. It swaps the address to little endian before
+ * writing it to config address, and swaps the value to big endian
+ * before returning to the caller.
+ */
+unsigned int mpc824x_mpc107_getreg (unsigned int regNum)
+{
+ unsigned int temp;
+
+ /* swap the addr. to little endian */
+ *(volatile unsigned int *) CHRP_REG_ADDR = PCISWAP (regNum);
+ temp = *(volatile unsigned int *) CHRP_REG_DATA;
+ return PCISWAP (temp); /* swap the data upon return */
+}
+
+/*
+ * This procedure writes a 32-bit address MPC107 register. It swaps
+ * the address to little endian before writing it to config address.
+ */
+
+void mpc824x_mpc107_setreg (unsigned int regNum, unsigned int regVal)
+{
+ /* swap the addr. to little endian */
+ *(volatile unsigned int *) CHRP_REG_ADDR = PCISWAP (regNum);
+ *(volatile unsigned int *) CHRP_REG_DATA = PCISWAP (regVal);
+ return;
+}
+
+
+/*
+ * Write a byte (8 bits) to a memory location.
+ */
+void mpc824x_mpc107_write8 (unsigned int addr, unsigned char data)
+{
+ *(unsigned char *) addr = data;
+ __asm__ ("sync");
+}
+
+/*
+ * Write a word (16 bits) to a memory location after the value
+ * has been byte swapped (big to little endian or vice versa)
+ */
+
+void mpc824x_mpc107_write16 (unsigned int address, unsigned short data)
+{
+ *(volatile unsigned short *) address = BYTE_SWAP_16_BIT (data);
+ __asm__ ("sync");
+}
+
+/*
+ * Write a long word (32 bits) to a memory location after the value
+ * has been byte swapped (big to little endian or vice versa)
+ */
+
+void mpc824x_mpc107_write32 (unsigned int address, unsigned int data)
+{
+ *(volatile unsigned int *) address = LONGSWAP (data);
+ __asm__ ("sync");
+}
+
+/*
+ * Read a byte (8 bits) from a memory location.
+ */
+unsigned char mpc824x_mpc107_read8 (unsigned int addr)
+{
+ return *(volatile unsigned char *) addr;
+}
+
+
+/*
+ * Read a word (16 bits) from a memory location, and byte swap the
+ * value before returning to the caller.
+ */
+unsigned short mpc824x_mpc107_read16 (unsigned int address)
+{
+ unsigned short retVal;
+
+ retVal = BYTE_SWAP_16_BIT (*(unsigned short *) address);
+ return retVal;
+}
+
+
+/*
+ * Read a long word (32 bits) from a memory location, and byte
+ * swap the value before returning to the caller.
+ */
+unsigned int mpc824x_mpc107_read32 (unsigned int address)
+{
+ unsigned int retVal;
+
+ retVal = LONGSWAP (*(unsigned int *) address);
+ return (retVal);
+}
+
+
+/*
+ * Read a register in the Embedded Utilities Memory Block address
+ * space.
+ * Input: regNum - register number + utility base address. Example,
+ * the base address of EPIC is 0x40000, the register number
+ * being passed is 0x40000+the address of the target register.
+ * (See epic.h for register addresses).
+ * Output: The 32 bit little endian value of the register.
+ */
+
+unsigned int mpc824x_eummbar_read (unsigned int regNum)
+{
+ unsigned int temp;
+
+ temp = *(volatile unsigned int *) (EUMBBAR_VAL + regNum);
+ temp = PCISWAP (temp);
+ return temp;
+}
+
+
+/*
+ * Write a value to a register in the Embedded Utilities Memory
+ * Block address space.
+ * Input: regNum - register number + utility base address. Example,
+ * the base address of EPIC is 0x40000, the register
+ * number is 0x40000+the address of the target register.
+ * (See epic.h for register addresses).
+ * regVal - value to be written to the register.
+ */
+
+void mpc824x_eummbar_write (unsigned int regNum, unsigned int regVal)
+{
+ *(volatile unsigned int *) (EUMBBAR_VAL + regNum) = PCISWAP (regVal);
+ return;
+}
+
+/* ------------------------------------------------------------------------- */
diff --git a/cpu/mpc824x/interrupts.c b/cpu/mpc824x/interrupts.c
new file mode 100644
index 0000000..2011671
--- /dev/null
+++ b/cpu/mpc824x/interrupts.c
@@ -0,0 +1,185 @@
+/*
+ * (C) Copyright 2000-2002
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ * Rob Taylor, Flying Pig Systems. robt@flyingpig.com
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <mpc824x.h>
+#include <asm/processor.h>
+#include <asm/pci_io.h>
+#include <commproc.h>
+#include "drivers/epic.h"
+
+/****************************************************************************/
+
+unsigned decrementer_count; /* count val for 1e6/HZ microseconds */
+
+static __inline__ unsigned long get_msr (void)
+{
+ unsigned long msr;
+
+ asm volatile ("mfmsr %0":"=r" (msr):);
+
+ return msr;
+}
+
+static __inline__ void set_msr (unsigned long msr)
+{
+ asm volatile ("mtmsr %0"::"r" (msr));
+}
+
+static __inline__ unsigned long get_dec (void)
+{
+ unsigned long val;
+
+ asm volatile ("mfdec %0":"=r" (val):);
+
+ return val;
+}
+
+
+static __inline__ void set_dec (unsigned long val)
+{
+ asm volatile ("mtdec %0"::"r" (val));
+}
+
+
+void enable_interrupts (void)
+{
+ set_msr (get_msr () | MSR_EE);
+}
+
+/* returns flag if MSR_EE was set before */
+int disable_interrupts (void)
+{
+ ulong msr = get_msr ();
+
+ set_msr (msr & ~MSR_EE);
+ return ((msr & MSR_EE) != 0);
+}
+
+/****************************************************************************/
+
+int interrupt_init (void)
+{
+ decrementer_count = (get_bus_freq (0) / 4) / CFG_HZ;
+
+ /*
+ * It's all broken at the moment and I currently don't need
+ * interrupts. If you want to fix it, have a look at the epic
+ * drivers in dink32 v12. They do everthing and Motorola said
+ * I could use the dink source in this project as long as
+ * copyright notices remain intact.
+ */
+
+ epicInit (EPIC_DIRECT_IRQ, 0);
+
+ set_dec (decrementer_count);
+
+ set_msr (get_msr () | MSR_EE);
+
+ return (0);
+}
+
+/****************************************************************************/
+
+/*
+ * Handle external interrupts
+ */
+void external_interrupt (struct pt_regs *regs)
+{
+ register unsigned long temp;
+
+ pci_readl (CFG_EUMB_ADDR + EPIC_PROC_INT_ACK_REG, temp);
+ sync (); /* i'm not convinced this is needed, but dink source has it */
+ temp &= 0xff; /*get vector */
+
+ /*TODO: handle them -... */
+ epicEOI ();
+}
+
+/****************************************************************************/
+
+/*
+ * blank int handlers.
+ */
+
+void
+irq_install_handler (int vec, interrupt_handler_t * handler, void *arg)
+{
+}
+
+void irq_free_handler (int vec)
+{
+
+}
+
+/*TODO: some handlers for winbond and 87308 interrupts
+ and what about generic pci inteerupts?
+ vga?
+ */
+
+volatile ulong timestamp = 0;
+
+void timer_interrupt (struct pt_regs *regs)
+{
+ /* Restore Decrementer Count */
+ set_dec (decrementer_count);
+
+ timestamp++;
+
+#if defined(CONFIG_WATCHDOG)
+ if ((timestamp % (CFG_HZ / 2)) == 0) {
+#if defined(CONFIG_OXC)
+ {
+ extern void oxc_wdt_reset (void);
+
+ oxc_wdt_reset ();
+ }
+#endif
+ }
+#endif /* CONFIG_WATCHDOG */
+#if defined(CONFIG_SHOW_ACTIVITY) && defined(CONFIG_OXC)
+ if ((timestamp % (CFG_HZ / 10)) == 0) {
+ {
+ extern void oxc_toggle_activeled (void);
+
+ oxc_toggle_activeled ();
+ }
+ }
+#endif
+}
+
+void reset_timer (void)
+{
+ timestamp = 0;
+}
+
+ulong get_timer (ulong base)
+{
+ return (timestamp - base);
+}
+
+void set_timer (ulong t)
+{
+ timestamp = t;
+}
diff --git a/cpu/mpc8260/cpu.c b/cpu/mpc8260/cpu.c
new file mode 100644
index 0000000..73881ee
--- /dev/null
+++ b/cpu/mpc8260/cpu.c
@@ -0,0 +1,243 @@
+/*
+ * (C) Copyright 2000
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+/*
+ * CPU specific code for the MPC8260
+ *
+ * written or collected and sometimes rewritten by
+ * Magnus Damm <damm@bitsmart.com>
+ *
+ * minor modifications by
+ * Wolfgang Denk <wd@denx.de>
+ *
+ * modified for 8260 by
+ * Murray Jensen <Murray.Jensen@cmst.csiro.au>
+ *
+ * added 8260 masks by
+ * Marius Groeger <mag@sysgo.de>
+ */
+
+#include <common.h>
+#include <watchdog.h>
+#include <command.h>
+#include <mpc8260.h>
+#include <asm/processor.h>
+#include <asm/cpm_8260.h>
+
+int checkcpu (void)
+{
+ DECLARE_GLOBAL_DATA_PTR;
+
+ volatile immap_t *immap = (immap_t *) CFG_IMMR;
+ ulong clock = gd->cpu_clk;
+ uint pvr = get_pvr ();
+ uint immr, rev, m, k;
+ char buf[32];
+
+ puts ("CPU: ");
+
+ if (((pvr >> 16) & 0xff) != 0x81)
+ return -1; /* whoops! not an MPC8260 */
+ rev = pvr & 0xff;
+
+ immr = immap->im_memctl.memc_immr;
+ if ((immr & IMMR_ISB_MSK) != CFG_IMMR)
+ return -1; /* whoops! someone moved the IMMR */
+
+ printf ("MPC8260 (Rev %02x, Mask ", rev);
+
+ /*
+ * the bottom 16 bits of the immr are the Part Number and Mask Number
+ * (4-34); the 16 bits at PROFF_REVNUM (0x8af0) in dual port ram is the
+ * RISC Microcode Revision Number (13-10).
+ * For the 8260, Motorola doesn't include the Microcode Revision
+ * in the mask.
+ */
+ m = immr & (IMMR_PARTNUM_MSK | IMMR_MASKNUM_MSK);
+ k = *((ushort *) & immap->im_dprambase[PROFF_REVNUM]);
+
+ switch (m) {
+ case 0x0000:
+ printf ("0.2 2J24M");
+ break;
+ case 0x0010:
+ printf ("A.0 K22A");
+ break;
+ case 0x0011:
+ printf ("A.1 1K22A-XC");
+ break;
+ case 0x0001:
+ printf ("B.1 1K23A");
+ break;
+ case 0x0021:
+ printf ("B.2 2K23A-XC");
+ break;
+ case 0x0023:
+ printf ("B.3 3K23A");
+ break;
+ case 0x0024:
+ printf ("C.2 6K23A");
+ break;
+ case 0x0060:
+ printf ("A.0(A) 2K25A");
+ break;
+ default:
+ printf ("unknown [immr=0x%04x,k=0x%04x]", m, k);
+ break;
+ }
+
+ printf (") at %s MHz\n", strmhz (buf, clock));
+
+ return 0;
+}
+
+/* ------------------------------------------------------------------------- */
+/* configures a UPM by writing into the UPM RAM array */
+/* uses bank 11 and a dummy physical address (=BRx_BA_MSK) */
+/* NOTE: the physical address chosen must not overlap into any other area */
+/* mapped by the memory controller because bank 11 has the lowest priority */
+
+void upmconfig (uint upm, uint * table, uint size)
+{
+ volatile immap_t *immap = (immap_t *) CFG_IMMR;
+ volatile memctl8260_t *memctl = &immap->im_memctl;
+ volatile uchar *dummy = (uchar *) BRx_BA_MSK; /* set all BA bits */
+ uint i;
+
+ /* first set up bank 11 to reference the correct UPM at a dummy address */
+
+ memctl->memc_or11 = ORxU_AM_MSK; /* set all AM bits */
+
+ switch (upm) {
+
+ case UPMA:
+ memctl->memc_br11 =
+ ((uint)dummy & BRx_BA_MSK) | BRx_PS_32 | BRx_MS_UPMA |
+ BRx_V;
+ memctl->memc_mamr = MxMR_OP_WARR;
+ break;
+
+ case UPMB:
+ memctl->memc_br11 =
+ ((uint)dummy & BRx_BA_MSK) | BRx_PS_32 | BRx_MS_UPMB |
+ BRx_V;
+ memctl->memc_mbmr = MxMR_OP_WARR;
+ break;
+
+ case UPMC:
+ memctl->memc_br11 =
+ ((uint)dummy & BRx_BA_MSK) | BRx_PS_32 | BRx_MS_UPMC |
+ BRx_V;
+ memctl->memc_mcmr = MxMR_OP_WARR;
+ break;
+
+ default:
+ panic ("upmconfig passed invalid UPM number (%u)\n", upm);
+ break;
+
+ }
+
+ /*
+ * at this point, the dummy address is set up to access the selected UPM,
+ * the MAD pointer is zero, and the MxMR OP is set for writing to RAM
+ *
+ * now we simply load the mdr with each word and poke the dummy address.
+ * the MAD is incremented on each access.
+ */
+
+ for (i = 0; i < size; i++) {
+ memctl->memc_mdr = table[i];
+ *dummy = 0;
+ }
+
+ /* now kill bank 11 */
+ memctl->memc_br11 = 0;
+}
+
+/* ------------------------------------------------------------------------- */
+
+int
+do_reset (cmd_tbl_t * cmdtp, bd_t * bd, int flag, int argc, char *argv[])
+{
+ ulong msr, addr;
+
+ volatile immap_t *immap = (immap_t *) CFG_IMMR;
+
+ immap->im_clkrst.car_rmr = RMR_CSRE; /* Checkstop Reset enable */
+
+ /* Interrupts and MMU off */
+ __asm__ __volatile__ ("mfmsr %0":"=r" (msr):);
+
+ msr &= ~(MSR_ME | MSR_EE | MSR_IR | MSR_DR);
+ __asm__ __volatile__ ("mtmsr %0"::"r" (msr));
+
+ /*
+ * Trying to execute the next instruction at a non-existing address
+ * should cause a machine check, resulting in reset
+ */
+#ifdef CFG_RESET_ADDRESS
+ addr = CFG_RESET_ADDRESS;
+#else
+ /*
+ * note: when CFG_MONITOR_BASE points to a RAM address, CFG_MONITOR_BASE
+ * - sizeof (ulong) is usually a valid address. Better pick an address
+ * known to be invalid on your system and assign it to CFG_RESET_ADDRESS.
+ */
+ addr = CFG_MONITOR_BASE - sizeof (ulong);
+#endif
+ ((void (*)(void)) addr) ();
+ return 1;
+
+}
+
+/* ------------------------------------------------------------------------- */
+
+/*
+ * Get timebase clock frequency (like cpu_clk in Hz)
+ *
+ */
+unsigned long get_tbclk (void)
+{
+ DECLARE_GLOBAL_DATA_PTR;
+
+ ulong tbclk;
+
+ tbclk = (gd->bus_clk + 3L) / 4L;
+
+ return (tbclk);
+}
+
+/* ------------------------------------------------------------------------- */
+
+#if defined(CONFIG_WATCHDOG)
+void watchdog_reset (void)
+{
+ int re_enable = disable_interrupts ();
+
+ reset_8260_watchdog ((immap_t *) CFG_IMMR);
+ if (re_enable)
+ enable_interrupts ();
+}
+#endif /* CONFIG_WATCHDOG */
+
+/* ------------------------------------------------------------------------- */
diff --git a/cpu/mpc8260/interrupts.c b/cpu/mpc8260/interrupts.c
new file mode 100644
index 0000000..d804408
--- /dev/null
+++ b/cpu/mpc8260/interrupts.c
@@ -0,0 +1,383 @@
+/*
+ * (C) Copyright 2000-2002
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ *
+ * Hacked for MPC8260 by Murray.Jensen@cmst.csiro.au, 22-Oct-00
+ */
+
+#include <common.h>
+#include <watchdog.h>
+#include <command.h>
+#include <mpc8260.h>
+#include <mpc8260_irq.h>
+#include <asm/processor.h>
+
+/****************************************************************************/
+
+unsigned decrementer_count; /* count val for 1e6/HZ microseconds */
+
+struct irq_action {
+ interrupt_handler_t *handler;
+ void *arg;
+ ulong count;
+};
+
+static struct irq_action irq_handlers[NR_IRQS];
+
+static ulong ppc_cached_irq_mask[NR_MASK_WORDS];
+
+/****************************************************************************/
+/* this section was ripped out of arch/ppc/kernel/ppc8260_pic.c in the */
+/* Linux/PPC 2.4.x source. There was no copyright notice in that file. */
+
+/* The 8260 internal interrupt controller. It is usually
+ * the only interrupt controller.
+ * There are two 32-bit registers (high/low) for up to 64
+ * possible interrupts.
+ *
+ * Now, the fun starts.....Interrupt Numbers DO NOT MAP
+ * in a simple arithmetic fashion to mask or pending registers.
+ * That is, interrupt 4 does not map to bit position 4.
+ * We create two tables, indexed by vector number, to indicate
+ * which register to use and which bit in the register to use.
+ */
+static u_char irq_to_siureg[] = {
+ 1, 1, 1, 1, 1, 1, 1, 1,
+ 1, 1, 1, 1, 1, 1, 1, 1,
+ 0, 0, 0, 0, 0, 0, 0, 0,
+ 0, 0, 0, 0, 0, 0, 0, 0,
+ 1, 1, 1, 1, 1, 1, 1, 1,
+ 1, 1, 1, 1, 1, 1, 1, 1,
+ 0, 0, 0, 0, 0, 0, 0, 0,
+ 0, 0, 0, 0, 0, 0, 0, 0
+};
+
+static u_char irq_to_siubit[] = {
+ 31, 16, 17, 18, 19, 20, 21, 22,
+ 23, 24, 25, 26, 27, 28, 29, 30,
+ 29, 30, 16, 17, 18, 19, 20, 21,
+ 22, 23, 24, 25, 26, 27, 28, 31,
+ 0, 1, 2, 3, 4, 5, 6, 7,
+ 8, 9, 10, 11, 12, 13, 14, 15,
+ 15, 14, 13, 12, 11, 10, 9, 8,
+ 7, 6, 5, 4, 3, 2, 1, 0
+};
+
+static void m8260_mask_irq (unsigned int irq_nr)
+{
+ volatile immap_t *immr = (immap_t *) CFG_IMMR;
+ int bit, word;
+ volatile uint *simr;
+
+ bit = irq_to_siubit[irq_nr];
+ word = irq_to_siureg[irq_nr];
+
+ simr = &(immr->im_intctl.ic_simrh);
+ ppc_cached_irq_mask[word] &= ~(1 << (31 - bit));
+ simr[word] = ppc_cached_irq_mask[word];
+}
+
+static void m8260_unmask_irq (unsigned int irq_nr)
+{
+ volatile immap_t *immr = (immap_t *) CFG_IMMR;
+ int bit, word;
+ volatile uint *simr;
+
+ bit = irq_to_siubit[irq_nr];
+ word = irq_to_siureg[irq_nr];
+
+ simr = &(immr->im_intctl.ic_simrh);
+ ppc_cached_irq_mask[word] |= (1 << (31 - bit));
+ simr[word] = ppc_cached_irq_mask[word];
+}
+
+static void m8260_mask_and_ack (unsigned int irq_nr)
+{
+ volatile immap_t *immr = (immap_t *) CFG_IMMR;
+ int bit, word;
+ volatile uint *simr, *sipnr;
+
+ bit = irq_to_siubit[irq_nr];
+ word = irq_to_siureg[irq_nr];
+
+ simr = &(immr->im_intctl.ic_simrh);
+ sipnr = &(immr->im_intctl.ic_sipnrh);
+ ppc_cached_irq_mask[word] &= ~(1 << (31 - bit));
+ simr[word] = ppc_cached_irq_mask[word];
+ sipnr[word] = 1 << (31 - bit);
+}
+
+static int m8260_get_irq (struct pt_regs *regs)
+{
+ volatile immap_t *immr = (immap_t *) CFG_IMMR;
+ int irq;
+ unsigned long bits;
+
+ /* For MPC8260, read the SIVEC register and shift the bits down
+ * to get the irq number. */
+ bits = immr->im_intctl.ic_sivec;
+ irq = bits >> 26;
+ return irq;
+}
+
+/* end of code ripped out of arch/ppc/kernel/ppc8260_pic.c */
+/****************************************************************************/
+
+static __inline__ unsigned long get_msr (void)
+{
+ unsigned long msr;
+
+ __asm__ __volatile__ ("mfmsr %0":"=r" (msr):);
+
+ return msr;
+}
+
+static __inline__ void set_msr (unsigned long msr)
+{
+ __asm__ __volatile__ ("mtmsr %0"::"r" (msr));
+}
+
+static __inline__ unsigned long get_dec (void)
+{
+ unsigned long val;
+
+ __asm__ __volatile__ ("mfdec %0":"=r" (val):);
+
+ return val;
+}
+
+static __inline__ void set_dec (unsigned long val)
+{
+ __asm__ __volatile__ ("mtdec %0"::"r" (val));
+}
+
+void enable_interrupts (void)
+{
+ set_msr (get_msr () | MSR_EE);
+}
+
+/* returns flag if MSR_EE was set before */
+int disable_interrupts (void)
+{
+ ulong msr = get_msr ();
+
+ set_msr (msr & ~MSR_EE);
+ return ((msr & MSR_EE) != 0);
+}
+
+/****************************************************************************/
+
+int interrupt_init (void)
+{
+ DECLARE_GLOBAL_DATA_PTR;
+
+ volatile immap_t *immr = (immap_t *) CFG_IMMR;
+
+ decrementer_count = (gd->bus_clk / 4) / CFG_HZ;
+
+ /* Initialize the default interrupt mapping priorities */
+ immr->im_intctl.ic_sicr = 0;
+ immr->im_intctl.ic_siprr = 0x05309770;
+ immr->im_intctl.ic_scprrh = 0x05309770;
+ immr->im_intctl.ic_scprrl = 0x05309770;
+
+ /* disable all interrupts and clear all pending bits */
+ immr->im_intctl.ic_simrh = ppc_cached_irq_mask[0] = 0;
+ immr->im_intctl.ic_simrl = ppc_cached_irq_mask[1] = 0;
+ immr->im_intctl.ic_sipnrh = 0xffffffff;
+ immr->im_intctl.ic_sipnrl = 0xffffffff;
+
+ set_dec (decrementer_count);
+
+ set_msr (get_msr () | MSR_EE);
+
+ return (0);
+}
+
+/****************************************************************************/
+
+/*
+ * Handle external interrupts
+ */
+void external_interrupt (struct pt_regs *regs)
+{
+ int irq, unmask = 1;
+
+ irq = m8260_get_irq (regs);
+
+ m8260_mask_and_ack (irq);
+
+ set_msr (get_msr () | MSR_EE);
+
+ if (irq_handlers[irq].handler != NULL)
+ (*irq_handlers[irq].handler) (irq_handlers[irq].arg);
+ else {
+ printf ("\nBogus External Interrupt IRQ %d\n", irq);
+ /*
+ * turn off the bogus interrupt, otherwise it
+ * might repeat forever
+ */
+ unmask = 0;
+ }
+
+ if (unmask)
+ m8260_unmask_irq (irq);
+}
+
+/****************************************************************************/
+
+/*
+ * Install and free an interrupt handler.
+ */
+
+void
+irq_install_handler (int irq, interrupt_handler_t * handler, void *arg)
+{
+ if (irq < 0 || irq >= NR_IRQS) {
+ printf ("irq_install_handler: bad irq number %d\n", irq);
+ return;
+ }
+
+ if (irq_handlers[irq].handler != NULL)
+ printf ("irq_install_handler: 0x%08lx replacing 0x%08lx\n",
+ (ulong) handler, (ulong) irq_handlers[irq].handler);
+
+ irq_handlers[irq].handler = handler;
+ irq_handlers[irq].arg = arg;
+
+ m8260_unmask_irq (irq);
+}
+
+void irq_free_handler (int irq)
+{
+ if (irq < 0 || irq >= NR_IRQS) {
+ printf ("irq_free_handler: bad irq number %d\n", irq);
+ return;
+ }
+
+ m8260_mask_irq (irq);
+
+ irq_handlers[irq].handler = NULL;
+ irq_handlers[irq].arg = NULL;
+}
+
+/****************************************************************************/
+
+volatile ulong timestamp = 0;
+
+/*
+ * timer_interrupt - gets called when the decrementer overflows,
+ * with interrupts disabled.
+ * Trivial implementation - no need to be really accurate.
+ */
+void timer_interrupt (struct pt_regs *regs)
+{
+#if defined(CONFIG_WATCHDOG) || defined(CFG_HYMOD_DBLEDS)
+ volatile immap_t *immr = (immap_t *) CFG_IMMR;
+#endif /* CONFIG_WATCHDOG */
+
+ /* Restore Decrementer Count */
+ set_dec (decrementer_count);
+
+ timestamp++;
+
+#if defined(CONFIG_WATCHDOG) || \
+ defined(CFG_CMA_LCD_HEARTBEAT) || \
+ defined(CFG_HYMOD_DBLEDS)
+
+ if ((timestamp % CFG_HZ) == 0) {
+#if defined(CFG_CMA_LCD_HEARTBEAT)
+ extern void lcd_heartbeat (void);
+#endif /* CFG_CMA_LCD_HEARTBEAT */
+#if defined(CFG_HYMOD_DBLEDS)
+ volatile iop8260_t *iop = &immr->im_ioport;
+ static int shift = 0;
+#endif /* CFG_HYMOD_DBLEDS */
+
+#if defined(CFG_CMA_LCD_HEARTBEAT)
+ lcd_heartbeat ();
+#endif /* CFG_CMA_LCD_HEARTBEAT */
+
+#if defined(CONFIG_WATCHDOG)
+ reset_8260_watchdog (immr);
+#endif /* CONFIG_WATCHDOG */
+
+#if defined(CFG_HYMOD_DBLEDS)
+ /* hymod daughter board LEDs */
+ if (++shift > 3)
+ shift = 0;
+ iop->iop_pdatd =
+ (iop->iop_pdatd & ~0x0f000000) | (1 << (24 + shift));
+#endif /* CFG_HYMOD_DBLEDS */
+ }
+#endif /* CONFIG_WATCHDOG || CFG_CMA_LCD_HEARTBEAT */
+}
+
+/****************************************************************************/
+
+void reset_timer (void)
+{
+ timestamp = 0;
+}
+
+ulong get_timer (ulong base)
+{
+ return (timestamp - base);
+}
+
+void set_timer (ulong t)
+{
+ timestamp = t;
+}
+
+/****************************************************************************/
+
+#if (CONFIG_COMMANDS & CFG_CMD_IRQ)
+
+/* ripped this out of ppc4xx/interrupts.c */
+
+/*******************************************************************************
+*
+* irqinfo - print information about PCI devices
+*
+*/
+void
+do_irqinfo (cmd_tbl_t * cmdtp, bd_t * bd, int flag, int argc, char *argv[])
+{
+ int irq, re_enable;
+
+ re_enable = disable_interrupts ();
+
+ printf ("\nInterrupt-Information:\n");
+ printf ("Nr Routine Arg Count\n");
+
+ for (irq = 0; irq < 32; irq++)
+ if (irq_handlers[irq].handler != NULL)
+ printf ("%02d %08lx %08lx %ld\n", irq,
+ (ulong) irq_handlers[irq].handler,
+ (ulong) irq_handlers[irq].arg,
+ irq_handlers[irq].count);
+
+ if (re_enable)
+ enable_interrupts ();
+}
+
+#endif /* CONFIG_COMMANDS & CFG_CMD_IRQ */
diff --git a/cpu/mpc8260/serial_scc.c b/cpu/mpc8260/serial_scc.c
new file mode 100644
index 0000000..ca76302
--- /dev/null
+++ b/cpu/mpc8260/serial_scc.c
@@ -0,0 +1,498 @@
+/*
+ * (C) Copyright 2000
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ *
+ * Hacked for MPC8260 by Murray.Jensen@cmst.csiro.au, 19-Oct-00.
+ */
+
+/*
+ * Minimal serial functions needed to use one of the SCC ports
+ * as serial console interface.
+ */
+
+#include <common.h>
+#include <mpc8260.h>
+#include <asm/cpm_8260.h>
+
+#if defined(CONFIG_CONS_ON_SCC)
+
+#if CONFIG_CONS_INDEX == 1 /* Console on SCC1 */
+
+#define SCC_INDEX 0
+#define PROFF_SCC PROFF_SCC1
+#define CMXSCR_MASK (CMXSCR_GR1|CMXSCR_SC1|\
+ CMXSCR_RS1CS_MSK|CMXSCR_TS1CS_MSK)
+#define CMXSCR_VALUE (CMXSCR_RS1CS_BRG1|CMXSCR_TS1CS_BRG1)
+#define CPM_CR_SCC_PAGE CPM_CR_SCC1_PAGE
+#define CPM_CR_SCC_SBLOCK CPM_CR_SCC1_SBLOCK
+
+#elif CONFIG_CONS_INDEX == 2 /* Console on SCC2 */
+
+#define SCC_INDEX 1
+#define PROFF_SCC PROFF_SCC2
+#define CMXSCR_MASK (CMXSCR_GR2|CMXSCR_SC2|\
+ CMXSCR_RS2CS_MSK|CMXSCR_TS2CS_MSK)
+#define CMXSCR_VALUE (CMXSCR_RS2CS_BRG2|CMXSCR_TS2CS_BRG2)
+#define CPM_CR_SCC_PAGE CPM_CR_SCC2_PAGE
+#define CPM_CR_SCC_SBLOCK CPM_CR_SCC2_SBLOCK
+
+#elif CONFIG_CONS_INDEX == 3 /* Console on SCC3 */
+
+#define SCC_INDEX 2
+#define PROFF_SCC PROFF_SCC3
+#define CMXSCR_MASK (CMXSCR_GR3|CMXSCR_SC3|\
+ CMXSCR_RS3CS_MSK|CMXSCR_TS3CS_MSK)
+#define CMXSCR_VALUE (CMXSCR_RS3CS_BRG3|CMXSCR_TS3CS_BRG3)
+#define CPM_CR_SCC_PAGE CPM_CR_SCC3_PAGE
+#define CPM_CR_SCC_SBLOCK CPM_CR_SCC3_SBLOCK
+
+#elif CONFIG_CONS_INDEX == 4 /* Console on SCC4 */
+
+#define SCC_INDEX 3
+#define PROFF_SCC PROFF_SCC4
+#define CMXSCR_MASK (CMXSCR_GR4|CMXSCR_SC4|\
+ CMXSCR_RS4CS_MSK|CMXSCR_TS4CS_MSK)
+#define CMXSCR_VALUE (CMXSCR_RS4CS_BRG4|CMXSCR_TS4CS_BRG4)
+#define CPM_CR_SCC_PAGE CPM_CR_SCC4_PAGE
+#define CPM_CR_SCC_SBLOCK CPM_CR_SCC4_SBLOCK
+
+#else
+
+#error "console not correctly defined"
+
+#endif
+
+int serial_init (void)
+{
+ volatile immap_t *im = (immap_t *)CFG_IMMR;
+ volatile scc_t *sp;
+ volatile scc_uart_t *up;
+ volatile cbd_t *tbdf, *rbdf;
+ volatile cpm8260_t *cp = &(im->im_cpm);
+ uint dpaddr;
+
+ /* initialize pointers to SCC */
+
+ sp = (scc_t *) &(im->im_scc[SCC_INDEX]);
+ up = (scc_uart_t *)&im->im_dprambase[PROFF_SCC];
+
+ /* Disable transmitter/receiver.
+ */
+ sp->scc_gsmrl &= ~(SCC_GSMRL_ENR | SCC_GSMRL_ENT);
+
+ /* put the SCC channel into NMSI (non multiplexd serial interface)
+ * mode and wire the selected SCC Tx and Rx clocks to BRGx (15-15).
+ */
+ im->im_cpmux.cmx_scr = (im->im_cpmux.cmx_scr&~CMXSCR_MASK)|CMXSCR_VALUE;
+
+ /* Set up the baud rate generator.
+ */
+ serial_setbrg ();
+
+ /* Allocate space for two buffer descriptors in the DP ram.
+ * damm: allocating space after the two buffers for rx/tx data
+ */
+
+ dpaddr = m8260_cpm_dpalloc((2 * sizeof (cbd_t)) + 2, 16);
+
+ /* Set the physical address of the host memory buffers in
+ * the buffer descriptors.
+ */
+ rbdf = (cbd_t *)&im->im_dprambase[dpaddr];
+ rbdf->cbd_bufaddr = (uint) (rbdf+2);
+ rbdf->cbd_sc = BD_SC_EMPTY | BD_SC_WRAP;
+ tbdf = rbdf + 1;
+ tbdf->cbd_bufaddr = ((uint) (rbdf+2)) + 1;
+ tbdf->cbd_sc = BD_SC_WRAP;
+
+ /* Set up the uart parameters in the parameter ram.
+ */
+ up->scc_genscc.scc_rbase = dpaddr;
+ up->scc_genscc.scc_tbase = dpaddr+sizeof(cbd_t);
+ up->scc_genscc.scc_rfcr = CPMFCR_EB;
+ up->scc_genscc.scc_tfcr = CPMFCR_EB;
+ up->scc_genscc.scc_mrblr = 1;
+ up->scc_maxidl = 0;
+ up->scc_brkcr = 1;
+ up->scc_parec = 0;
+ up->scc_frmec = 0;
+ up->scc_nosec = 0;
+ up->scc_brkec = 0;
+ up->scc_uaddr1 = 0;
+ up->scc_uaddr2 = 0;
+ up->scc_toseq = 0;
+ up->scc_char1 = up->scc_char2 = up->scc_char3 = up->scc_char4 = 0x8000;
+ up->scc_char5 = up->scc_char6 = up->scc_char7 = up->scc_char8 = 0x8000;
+ up->scc_rccm = 0xc0ff;
+
+ /* Mask all interrupts and remove anything pending.
+ */
+ sp->scc_sccm = 0;
+ sp->scc_scce = 0xffff;
+
+ /* Set 8 bit FIFO, 16 bit oversampling and UART mode.
+ */
+ sp->scc_gsmrh = SCC_GSMRH_RFW; /* 8 bit FIFO */
+ sp->scc_gsmrl = \
+ SCC_GSMRL_TDCR_16 | SCC_GSMRL_RDCR_16 | SCC_GSMRL_MODE_UART;
+
+ /* Set CTS flow control, 1 stop bit, 8 bit character length,
+ * normal async UART mode, no parity
+ */
+ sp->scc_psmr = SCU_PSMR_FLC | SCU_PSMR_CL;
+
+ /* execute the "Init Rx and Tx params" CP command.
+ */
+
+ while (cp->cp_cpcr & CPM_CR_FLG) /* wait if cp is busy */
+ ;
+
+ cp->cp_cpcr = mk_cr_cmd(CPM_CR_SCC_PAGE, CPM_CR_SCC_SBLOCK,
+ 0, CPM_CR_INIT_TRX) | CPM_CR_FLG;
+
+ while (cp->cp_cpcr & CPM_CR_FLG) /* wait if cp is busy */
+ ;
+
+ /* Enable transmitter/receiver.
+ */
+ sp->scc_gsmrl |= SCC_GSMRL_ENR | SCC_GSMRL_ENT;
+
+ return (0);
+}
+
+void
+serial_setbrg (void)
+{
+ DECLARE_GLOBAL_DATA_PTR;
+
+#if defined(CONFIG_CONS_USE_EXTC)
+ m8260_cpm_extcbrg(SCC_INDEX, gd->baudrate,
+ CONFIG_CONS_EXTC_RATE, CONFIG_CONS_EXTC_PINSEL);
+#else
+ m8260_cpm_setbrg(SCC_INDEX, gd->baudrate);
+#endif
+}
+
+void
+serial_putc(const char c)
+{
+ volatile scc_uart_t *up;
+ volatile cbd_t *tbdf;
+ volatile immap_t *im;
+
+ if (c == '\n')
+ serial_putc ('\r');
+
+ im = (immap_t *)CFG_IMMR;
+ up = (scc_uart_t *)&im->im_dprambase[PROFF_SCC];
+ tbdf = (cbd_t *)&im->im_dprambase[up->scc_genscc.scc_tbase];
+
+ /* Wait for last character to go.
+ */
+ while (tbdf->cbd_sc & BD_SC_READY)
+ ;
+
+ /* Load the character into the transmit buffer.
+ */
+ *(volatile char *)tbdf->cbd_bufaddr = c;
+ tbdf->cbd_datlen = 1;
+ tbdf->cbd_sc |= BD_SC_READY;
+}
+
+void
+serial_puts (const char *s)
+{
+ while (*s) {
+ serial_putc (*s++);
+ }
+}
+
+int
+serial_getc(void)
+{
+ volatile cbd_t *rbdf;
+ volatile scc_uart_t *up;
+ volatile immap_t *im;
+ unsigned char c;
+
+ im = (immap_t *)CFG_IMMR;
+ up = (scc_uart_t *)&im->im_dprambase[PROFF_SCC];
+ rbdf = (cbd_t *)&im->im_dprambase[up->scc_genscc.scc_rbase];
+
+ /* Wait for character to show up.
+ */
+ while (rbdf->cbd_sc & BD_SC_EMPTY)
+ ;
+
+ /* Grab the char and clear the buffer again.
+ */
+ c = *(volatile unsigned char *)rbdf->cbd_bufaddr;
+ rbdf->cbd_sc |= BD_SC_EMPTY;
+
+ return (c);
+}
+
+int
+serial_tstc()
+{
+ volatile cbd_t *rbdf;
+ volatile scc_uart_t *up;
+ volatile immap_t *im;
+
+ im = (immap_t *)CFG_IMMR;
+ up = (scc_uart_t *)&im->im_dprambase[PROFF_SCC];
+ rbdf = (cbd_t *)&im->im_dprambase[up->scc_genscc.scc_rbase];
+
+ return ((rbdf->cbd_sc & BD_SC_EMPTY) == 0);
+}
+
+#endif /* CONFIG_CONS_ON_SCC */
+
+#if defined(CONFIG_KGDB_ON_SCC)
+
+#if defined(CONFIG_CONS_ON_SCC) && CONFIG_KGDB_INDEX == CONFIG_CONS_INDEX
+#error Whoops! serial console and kgdb are on the same scc serial port
+#endif
+
+#if CONFIG_KGDB_INDEX == 1 /* KGDB Port on SCC1 */
+
+#define KGDB_SCC_INDEX 0
+#define KGDB_PROFF_SCC PROFF_SCC1
+#define KGDB_CMXSCR_MASK (CMXSCR_GR1|CMXSCR_SC1|\
+ CMXSCR_RS1CS_MSK|CMXSCR_TS1CS_MSK)
+#define KGDB_CMXSCR_VALUE (CMXSCR_RS1CS_BRG1|CMXSCR_TS1CS_BRG1)
+#define KGDB_CPM_CR_SCC_PAGE CPM_CR_SCC1_PAGE
+#define KGDB_CPM_CR_SCC_SBLOCK CPM_CR_SCC1_SBLOCK
+
+#elif CONFIG_KGDB_INDEX == 2 /* KGDB Port on SCC2 */
+
+#define KGDB_SCC_INDEX 1
+#define KGDB_PROFF_SCC PROFF_SCC2
+#define KGDB_CMXSCR_MASK (CMXSCR_GR2|CMXSCR_SC2|\
+ CMXSCR_RS2CS_MSK|CMXSCR_TS2CS_MSK)
+#define KGDB_CMXSCR_VALUE (CMXSCR_RS2CS_BRG2|CMXSCR_TS2CS_BRG2)
+#define KGDB_CPM_CR_SCC_PAGE CPM_CR_SCC2_PAGE
+#define KGDB_CPM_CR_SCC_SBLOCK CPM_CR_SCC2_SBLOCK
+
+#elif CONFIG_KGDB_INDEX == 3 /* KGDB Port on SCC3 */
+
+#define KGDB_SCC_INDEX 2
+#define KGDB_PROFF_SCC PROFF_SCC3
+#define KGDB_CMXSCR_MASK (CMXSCR_GR3|CMXSCR_SC3|\
+ CMXSCR_RS3CS_MSK|CMXSCR_TS3CS_MSK)
+#define KGDB_CMXSCR_VALUE (CMXSCR_RS3CS_BRG3|CMXSCR_TS3CS_BRG3)
+#define KGDB_CPM_CR_SCC_PAGE CPM_CR_SCC3_PAGE
+#define KGDB_CPM_CR_SCC_SBLOCK CPM_CR_SCC3_SBLOCK
+
+#elif CONFIG_KGDB_INDEX == 4 /* KGDB Port on SCC4 */
+
+#define KGDB_SCC_INDEX 3
+#define KGDB_PROFF_SCC PROFF_SCC4
+#define KGDB_CMXSCR_MASK (CMXSCR_GR4|CMXSCR_SC4|\
+ CMXSCR_RS4CS_MSK|CMXSCR_TS4CS_MSK)
+#define KGDB_CMXSCR_VALUE (CMXSCR_RS4CS_BRG4|CMXSCR_TS4CS_BRG4)
+#define KGDB_CPM_CR_SCC_PAGE CPM_CR_SCC4_PAGE
+#define KGDB_CPM_CR_SCC_SBLOCK CPM_CR_SCC4_SBLOCK
+
+#else
+
+#error "kgdb serial port not correctly defined"
+
+#endif
+
+void
+kgdb_serial_init (void)
+{
+ volatile immap_t *im = (immap_t *)CFG_IMMR;
+ volatile scc_t *sp;
+ volatile scc_uart_t *up;
+ volatile cbd_t *tbdf, *rbdf;
+ volatile cpm8260_t *cp = &(im->im_cpm);
+ uint dpaddr, speed = CONFIG_KGDB_BAUDRATE;
+ char *s, *e;
+
+ if ((s = getenv("kgdbrate")) != NULL && *s != '\0') {
+ ulong rate = simple_strtoul(s, &e, 10);
+ if (e > s && *e == '\0')
+ speed = rate;
+ }
+
+ /* initialize pointers to SCC */
+
+ sp = (scc_t *) &(im->im_scc[KGDB_SCC_INDEX]);
+ up = (scc_uart_t *)&im->im_dprambase[KGDB_PROFF_SCC];
+
+ /* Disable transmitter/receiver.
+ */
+ sp->scc_gsmrl &= ~(SCC_GSMRL_ENR | SCC_GSMRL_ENT);
+
+ /* put the SCC channel into NMSI (non multiplexd serial interface)
+ * mode and wire the selected SCC Tx and Rx clocks to BRGx (15-15).
+ */
+ im->im_cpmux.cmx_scr = \
+ (im->im_cpmux.cmx_scr & ~KGDB_CMXSCR_MASK) | KGDB_CMXSCR_VALUE;
+
+ /* Set up the baud rate generator.
+ */
+#if defined(CONFIG_KGDB_USE_EXTC)
+ m8260_cpm_extcbrg(KGDB_SCC_INDEX, speed,
+ CONFIG_KGDB_EXTC_RATE, CONFIG_KGDB_EXTC_PINSEL);
+#else
+ m8260_cpm_setbrg(KGDB_SCC_INDEX, speed);
+#endif
+
+ /* Allocate space for two buffer descriptors in the DP ram.
+ * damm: allocating space after the two buffers for rx/tx data
+ */
+
+ dpaddr = m8260_cpm_dpalloc((2 * sizeof (cbd_t)) + 2, 16);
+
+ /* Set the physical address of the host memory buffers in
+ * the buffer descriptors.
+ */
+ rbdf = (cbd_t *)&im->im_dprambase[dpaddr];
+ rbdf->cbd_bufaddr = (uint) (rbdf+2);
+ rbdf->cbd_sc = BD_SC_EMPTY | BD_SC_WRAP;
+ tbdf = rbdf + 1;
+ tbdf->cbd_bufaddr = ((uint) (rbdf+2)) + 1;
+ tbdf->cbd_sc = BD_SC_WRAP;
+
+ /* Set up the uart parameters in the parameter ram.
+ */
+ up->scc_genscc.scc_rbase = dpaddr;
+ up->scc_genscc.scc_tbase = dpaddr+sizeof(cbd_t);
+ up->scc_genscc.scc_rfcr = CPMFCR_EB;
+ up->scc_genscc.scc_tfcr = CPMFCR_EB;
+ up->scc_genscc.scc_mrblr = 1;
+ up->scc_maxidl = 0;
+ up->scc_brkcr = 1;
+ up->scc_parec = 0;
+ up->scc_frmec = 0;
+ up->scc_nosec = 0;
+ up->scc_brkec = 0;
+ up->scc_uaddr1 = 0;
+ up->scc_uaddr2 = 0;
+ up->scc_toseq = 0;
+ up->scc_char1 = up->scc_char2 = up->scc_char3 = up->scc_char4 = 0x8000;
+ up->scc_char5 = up->scc_char6 = up->scc_char7 = up->scc_char8 = 0x8000;
+ up->scc_rccm = 0xc0ff;
+
+ /* Mask all interrupts and remove anything pending.
+ */
+ sp->scc_sccm = 0;
+ sp->scc_scce = 0xffff;
+
+ /* Set 8 bit FIFO, 16 bit oversampling and UART mode.
+ */
+ sp->scc_gsmrh = SCC_GSMRH_RFW; /* 8 bit FIFO */
+ sp->scc_gsmrl = \
+ SCC_GSMRL_TDCR_16 | SCC_GSMRL_RDCR_16 | SCC_GSMRL_MODE_UART;
+
+ /* Set CTS flow control, 1 stop bit, 8 bit character length,
+ * normal async UART mode, no parity
+ */
+ sp->scc_psmr = SCU_PSMR_FLC | SCU_PSMR_CL;
+
+ /* execute the "Init Rx and Tx params" CP command.
+ */
+
+ while (cp->cp_cpcr & CPM_CR_FLG) /* wait if cp is busy */
+ ;
+
+ cp->cp_cpcr = mk_cr_cmd(KGDB_CPM_CR_SCC_PAGE, KGDB_CPM_CR_SCC_SBLOCK,
+ 0, CPM_CR_INIT_TRX) | CPM_CR_FLG;
+
+ while (cp->cp_cpcr & CPM_CR_FLG) /* wait if cp is busy */
+ ;
+
+ /* Enable transmitter/receiver.
+ */
+ sp->scc_gsmrl |= SCC_GSMRL_ENR | SCC_GSMRL_ENT;
+
+ printf("SCC%d at %dbps ", CONFIG_KGDB_INDEX, speed);
+}
+
+void
+putDebugChar(const char c)
+{
+ volatile scc_uart_t *up;
+ volatile cbd_t *tbdf;
+ volatile immap_t *im;
+
+ if (c == '\n')
+ putDebugChar ('\r');
+
+ im = (immap_t *)CFG_IMMR;
+ up = (scc_uart_t *)&im->im_dprambase[KGDB_PROFF_SCC];
+ tbdf = (cbd_t *)&im->im_dprambase[up->scc_genscc.scc_tbase];
+
+ /* Wait for last character to go.
+ */
+ while (tbdf->cbd_sc & BD_SC_READY)
+ ;
+
+ /* Load the character into the transmit buffer.
+ */
+ *(volatile char *)tbdf->cbd_bufaddr = c;
+ tbdf->cbd_datlen = 1;
+ tbdf->cbd_sc |= BD_SC_READY;
+}
+
+void
+putDebugStr (const char *s)
+{
+ while (*s) {
+ putDebugChar (*s++);
+ }
+}
+
+int
+getDebugChar(void)
+{
+ volatile cbd_t *rbdf;
+ volatile scc_uart_t *up;
+ volatile immap_t *im;
+ unsigned char c;
+
+ im = (immap_t *)CFG_IMMR;
+ up = (scc_uart_t *)&im->im_dprambase[KGDB_PROFF_SCC];
+ rbdf = (cbd_t *)&im->im_dprambase[up->scc_genscc.scc_rbase];
+
+ /* Wait for character to show up.
+ */
+ while (rbdf->cbd_sc & BD_SC_EMPTY)
+ ;
+
+ /* Grab the char and clear the buffer again.
+ */
+ c = *(volatile unsigned char *)rbdf->cbd_bufaddr;
+ rbdf->cbd_sc |= BD_SC_EMPTY;
+
+ return (c);
+}
+
+void
+kgdb_interruptible(int yes)
+{
+ return;
+}
+
+#endif /* CONFIG_KGDB_ON_SCC */
diff --git a/cpu/mpc8260/serial_smc.c b/cpu/mpc8260/serial_smc.c
new file mode 100644
index 0000000..b0e1ce4
--- /dev/null
+++ b/cpu/mpc8260/serial_smc.c
@@ -0,0 +1,462 @@
+/*
+ * (C) Copyright 2000, 2001, 2002
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ *
+ * Hacked for MPC8260 by Murray.Jensen@cmst.csiro.au, 19-Oct-00, with
+ * changes based on the file arch/ppc/mbxboot/m8260_tty.c from the
+ * Linux/PPC sources (m8260_tty.c had no copyright info in it).
+ */
+
+/*
+ * Minimal serial functions needed to use one of the SMC ports
+ * as serial console interface.
+ */
+
+#include <common.h>
+#include <mpc8260.h>
+#include <asm/cpm_8260.h>
+
+#if defined(CONFIG_CONS_ON_SMC)
+
+#if CONFIG_CONS_INDEX == 1 /* Console on SMC1 */
+
+#define SMC_INDEX 0
+#define PROFF_SMC_BASE PROFF_SMC1_BASE
+#define PROFF_SMC PROFF_SMC1
+#define CPM_CR_SMC_PAGE CPM_CR_SMC1_PAGE
+#define CPM_CR_SMC_SBLOCK CPM_CR_SMC1_SBLOCK
+#define CMXSMR_MASK (CMXSMR_SMC1|CMXSMR_SMC1CS_MSK)
+#define CMXSMR_VALUE CMXSMR_SMC1CS_BRG7
+
+#elif CONFIG_CONS_INDEX == 2 /* Console on SMC2 */
+
+#define SMC_INDEX 1
+#define PROFF_SMC_BASE PROFF_SMC2_BASE
+#define PROFF_SMC PROFF_SMC2
+#define CPM_CR_SMC_PAGE CPM_CR_SMC2_PAGE
+#define CPM_CR_SMC_SBLOCK CPM_CR_SMC2_SBLOCK
+#define CMXSMR_MASK (CMXSMR_SMC2|CMXSMR_SMC2CS_MSK)
+#define CMXSMR_VALUE CMXSMR_SMC2CS_BRG8
+
+#else
+
+#error "console not correctly defined"
+
+#endif
+
+/* map rs_table index to baud rate generator index */
+static unsigned char brg_map[] = {
+ 6, /* BRG7 for SMC1 */
+ 7, /* BRG8 for SMC2 */
+ 0, /* BRG1 for SCC1 */
+ 1, /* BRG1 for SCC2 */
+ 2, /* BRG1 for SCC3 */
+ 3, /* BRG1 for SCC4 */
+};
+
+int serial_init (void)
+{
+ volatile immap_t *im = (immap_t *)CFG_IMMR;
+ volatile smc_t *sp;
+ volatile smc_uart_t *up;
+ volatile cbd_t *tbdf, *rbdf;
+ volatile cpm8260_t *cp = &(im->im_cpm);
+ uint dpaddr;
+
+ /* initialize pointers to SMC */
+
+ sp = (smc_t *) &(im->im_smc[SMC_INDEX]);
+ *(ushort *)(&im->im_dprambase[PROFF_SMC_BASE]) = PROFF_SMC;
+ up = (smc_uart_t *)&im->im_dprambase[PROFF_SMC];
+
+ /* Disable transmitter/receiver.
+ */
+ sp->smc_smcmr &= ~(SMCMR_REN | SMCMR_TEN);
+
+ /* NOTE: I/O port pins are set up via the iop_conf_tab[] table */
+
+ /* Allocate space for two buffer descriptors in the DP ram.
+ * damm: allocating space after the two buffers for rx/tx data
+ */
+
+ dpaddr = m8260_cpm_dpalloc((2 * sizeof (cbd_t)) + 2, 16);
+
+ /* Set the physical address of the host memory buffers in
+ * the buffer descriptors.
+ */
+ rbdf = (cbd_t *)&im->im_dprambase[dpaddr];
+ rbdf->cbd_bufaddr = (uint) (rbdf+2);
+ rbdf->cbd_sc = 0;
+ tbdf = rbdf + 1;
+ tbdf->cbd_bufaddr = ((uint) (rbdf+2)) + 1;
+ tbdf->cbd_sc = 0;
+
+ /* Set up the uart parameters in the parameter ram.
+ */
+ up->smc_rbase = dpaddr;
+ up->smc_tbase = dpaddr+sizeof(cbd_t);
+ up->smc_rfcr = CPMFCR_EB;
+ up->smc_tfcr = CPMFCR_EB;
+ up->smc_brklen = 0;
+ up->smc_brkec = 0;
+ up->smc_brkcr = 0;
+
+ /* Set UART mode, 8 bit, no parity, one stop.
+ * Enable receive and transmit.
+ */
+ sp->smc_smcmr = smcr_mk_clen(9) | SMCMR_SM_UART;
+
+ /* Mask all interrupts and remove anything pending.
+ */
+ sp->smc_smcm = 0;
+ sp->smc_smce = 0xff;
+
+ /* put the SMC channel into NMSI (non multiplexd serial interface)
+ * mode and wire either BRG7 to SMC1 or BRG8 to SMC2 (15-17).
+ */
+ im->im_cpmux.cmx_smr = (im->im_cpmux.cmx_smr&~CMXSMR_MASK)|CMXSMR_VALUE;
+
+ /* Set up the baud rate generator.
+ */
+ serial_setbrg ();
+
+ /* Make the first buffer the only buffer.
+ */
+ tbdf->cbd_sc |= BD_SC_WRAP;
+ rbdf->cbd_sc |= BD_SC_EMPTY | BD_SC_WRAP;
+
+ /* Single character receive.
+ */
+ up->smc_mrblr = 1;
+ up->smc_maxidl = 0;
+
+ /* Initialize Tx/Rx parameters.
+ */
+
+ while (cp->cp_cpcr & CPM_CR_FLG) /* wait if cp is busy */
+ ;
+
+ cp->cp_cpcr = mk_cr_cmd(CPM_CR_SMC_PAGE, CPM_CR_SMC_SBLOCK,
+ 0, CPM_CR_INIT_TRX) | CPM_CR_FLG;
+
+ while (cp->cp_cpcr & CPM_CR_FLG) /* wait if cp is busy */
+ ;
+
+ /* Enable transmitter/receiver.
+ */
+ sp->smc_smcmr |= SMCMR_REN | SMCMR_TEN;
+
+ return (0);
+}
+
+void
+serial_setbrg (void)
+{
+ DECLARE_GLOBAL_DATA_PTR;
+
+#if defined(CONFIG_CONS_USE_EXTC)
+ m8260_cpm_extcbrg(brg_map[SMC_INDEX], gd->baudrate,
+ CONFIG_CONS_EXTC_RATE, CONFIG_CONS_EXTC_PINSEL);
+#else
+ m8260_cpm_setbrg(brg_map[SMC_INDEX], gd->baudrate);
+#endif
+}
+
+void
+serial_putc(const char c)
+{
+ volatile cbd_t *tbdf;
+ volatile char *buf;
+ volatile smc_uart_t *up;
+ volatile immap_t *im = (immap_t *)CFG_IMMR;
+
+ if (c == '\n')
+ serial_putc ('\r');
+
+ up = (smc_uart_t *)&(im->im_dprambase[PROFF_SMC]);
+
+ tbdf = (cbd_t *)&im->im_dprambase[up->smc_tbase];
+
+ /* Wait for last character to go.
+ */
+ buf = (char *)tbdf->cbd_bufaddr;
+ while (tbdf->cbd_sc & BD_SC_READY)
+ ;
+
+ *buf = c;
+ tbdf->cbd_datlen = 1;
+ tbdf->cbd_sc |= BD_SC_READY;
+}
+
+void
+serial_puts (const char *s)
+{
+ while (*s) {
+ serial_putc (*s++);
+ }
+}
+
+int
+serial_getc(void)
+{
+ volatile cbd_t *rbdf;
+ volatile unsigned char *buf;
+ volatile smc_uart_t *up;
+ volatile immap_t *im = (immap_t *)CFG_IMMR;
+ unsigned char c;
+
+ up = (smc_uart_t *)&(im->im_dprambase[PROFF_SMC]);
+
+ rbdf = (cbd_t *)&im->im_dprambase[up->smc_rbase];
+
+ /* Wait for character to show up.
+ */
+ buf = (unsigned char *)rbdf->cbd_bufaddr;
+ while (rbdf->cbd_sc & BD_SC_EMPTY)
+ ;
+ c = *buf;
+ rbdf->cbd_sc |= BD_SC_EMPTY;
+
+ return(c);
+}
+
+int
+serial_tstc()
+{
+ volatile cbd_t *rbdf;
+ volatile smc_uart_t *up;
+ volatile immap_t *im = (immap_t *)CFG_IMMR;
+
+ up = (smc_uart_t *)&(im->im_dprambase[PROFF_SMC]);
+
+ rbdf = (cbd_t *)&im->im_dprambase[up->smc_rbase];
+
+ return(!(rbdf->cbd_sc & BD_SC_EMPTY));
+}
+
+#endif /* CONFIG_CONS_ON_SMC */
+
+#if defined(CONFIG_KGDB_ON_SMC)
+
+#if defined(CONFIG_CONS_ON_SMC) && CONFIG_KGDB_INDEX == CONFIG_CONS_INDEX
+#error Whoops! serial console and kgdb are on the same smc serial port
+#endif
+
+#if CONFIG_KGDB_INDEX == 1 /* KGDB Port on SMC1 */
+
+#define KGDB_SMC_INDEX 0
+#define KGDB_PROFF_SMC_BASE PROFF_SMC1_BASE
+#define KGDB_PROFF_SMC PROFF_SMC1
+#define KGDB_CPM_CR_SMC_PAGE CPM_CR_SMC1_PAGE
+#define KGDB_CPM_CR_SMC_SBLOCK CPM_CR_SMC1_SBLOCK
+#define KGDB_CMXSMR_MASK (CMXSMR_SMC1|CMXSMR_SMC1CS_MSK)
+#define KGDB_CMXSMR_VALUE CMXSMR_SMC1CS_BRG7
+
+#elif CONFIG_KGDB_INDEX == 2 /* KGDB Port on SMC2 */
+
+#define KGDB_SMC_INDEX 1
+#define KGDB_PROFF_SMC_BASE PROFF_SMC2_BASE
+#define KGDB_PROFF_SMC PROFF_SMC2
+#define KGDB_CPM_CR_SMC_PAGE CPM_CR_SMC2_PAGE
+#define KGDB_CPM_CR_SMC_SBLOCK CPM_CR_SMC2_SBLOCK
+#define KGDB_CMXSMR_MASK (CMXSMR_SMC2|CMXSMR_SMC2CS_MSK)
+#define KGDB_CMXSMR_VALUE CMXSMR_SMC2CS_BRG8
+
+#else
+
+#error "console not correctly defined"
+
+#endif
+
+void
+kgdb_serial_init (void)
+{
+ volatile immap_t *im = (immap_t *)CFG_IMMR;
+ volatile smc_t *sp;
+ volatile smc_uart_t *up;
+ volatile cbd_t *tbdf, *rbdf;
+ volatile cpm8260_t *cp = &(im->im_cpm);
+ uint dpaddr, speed = CONFIG_KGDB_BAUDRATE;
+ char *s, *e;
+
+ if ((s = getenv("kgdbrate")) != NULL && *s != '\0') {
+ ulong rate = simple_strtoul(s, &e, 10);
+ if (e > s && *e == '\0')
+ speed = rate;
+ }
+
+ /* initialize pointers to SMC */
+
+ sp = (smc_t *) &(im->im_smc[KGDB_SMC_INDEX]);
+ *(ushort *)(&im->im_dprambase[KGDB_PROFF_SMC_BASE]) = KGDB_PROFF_SMC;
+ up = (smc_uart_t *)&im->im_dprambase[KGDB_PROFF_SMC];
+
+ /* Disable transmitter/receiver.
+ */
+ sp->smc_smcmr &= ~(SMCMR_REN | SMCMR_TEN);
+
+ /* NOTE: I/O port pins are set up via the iop_conf_tab[] table */
+
+ /* Allocate space for two buffer descriptors in the DP ram.
+ * damm: allocating space after the two buffers for rx/tx data
+ */
+
+ dpaddr = m8260_cpm_dpalloc((2 * sizeof (cbd_t)) + 2, 16);
+
+ /* Set the physical address of the host memory buffers in
+ * the buffer descriptors.
+ */
+ rbdf = (cbd_t *)&im->im_dprambase[dpaddr];
+ rbdf->cbd_bufaddr = (uint) (rbdf+2);
+ rbdf->cbd_sc = 0;
+ tbdf = rbdf + 1;
+ tbdf->cbd_bufaddr = ((uint) (rbdf+2)) + 1;
+ tbdf->cbd_sc = 0;
+
+ /* Set up the uart parameters in the parameter ram.
+ */
+ up->smc_rbase = dpaddr;
+ up->smc_tbase = dpaddr+sizeof(cbd_t);
+ up->smc_rfcr = CPMFCR_EB;
+ up->smc_tfcr = CPMFCR_EB;
+ up->smc_brklen = 0;
+ up->smc_brkec = 0;
+ up->smc_brkcr = 0;
+
+ /* Set UART mode, 8 bit, no parity, one stop.
+ * Enable receive and transmit.
+ */
+ sp->smc_smcmr = smcr_mk_clen(9) | SMCMR_SM_UART;
+
+ /* Mask all interrupts and remove anything pending.
+ */
+ sp->smc_smcm = 0;
+ sp->smc_smce = 0xff;
+
+ /* put the SMC channel into NMSI (non multiplexd serial interface)
+ * mode and wire either BRG7 to SMC1 or BRG8 to SMC2 (15-17).
+ */
+ im->im_cpmux.cmx_smr =
+ (im->im_cpmux.cmx_smr & ~KGDB_CMXSMR_MASK) | KGDB_CMXSMR_VALUE;
+
+ /* Set up the baud rate generator.
+ */
+#if defined(CONFIG_KGDB_USE_EXTC)
+ m8260_cpm_extcbrg(KGDB_SMC_INDEX, speed,
+ CONFIG_KGDB_EXTC_RATE, CONFIG_KGDB_EXTC_PINSEL);
+#else
+ m8260_cpm_setbrg(KGDB_SMC_INDEX, speed);
+#endif
+
+ /* Make the first buffer the only buffer.
+ */
+ tbdf->cbd_sc |= BD_SC_WRAP;
+ rbdf->cbd_sc |= BD_SC_EMPTY | BD_SC_WRAP;
+
+ /* Single character receive.
+ */
+ up->smc_mrblr = 1;
+ up->smc_maxidl = 0;
+
+ /* Initialize Tx/Rx parameters.
+ */
+
+ while (cp->cp_cpcr & CPM_CR_FLG) /* wait if cp is busy */
+ ;
+
+ cp->cp_cpcr = mk_cr_cmd(KGDB_CPM_CR_SMC_PAGE, KGDB_CPM_CR_SMC_SBLOCK,
+ 0, CPM_CR_INIT_TRX) | CPM_CR_FLG;
+
+ while (cp->cp_cpcr & CPM_CR_FLG) /* wait if cp is busy */
+ ;
+
+ /* Enable transmitter/receiver.
+ */
+ sp->smc_smcmr |= SMCMR_REN | SMCMR_TEN;
+
+ printf("SMC%d at %dbps ", CONFIG_KGDB_INDEX, speed);
+}
+
+void
+putDebugChar(const char c)
+{
+ volatile cbd_t *tbdf;
+ volatile char *buf;
+ volatile smc_uart_t *up;
+ volatile immap_t *im = (immap_t *)CFG_IMMR;
+
+ if (c == '\n')
+ putDebugChar ('\r');
+
+ up = (smc_uart_t *)&(im->im_dprambase[KGDB_PROFF_SMC]);
+
+ tbdf = (cbd_t *)&im->im_dprambase[up->smc_tbase];
+
+ /* Wait for last character to go.
+ */
+ buf = (char *)tbdf->cbd_bufaddr;
+ while (tbdf->cbd_sc & BD_SC_READY)
+ ;
+
+ *buf = c;
+ tbdf->cbd_datlen = 1;
+ tbdf->cbd_sc |= BD_SC_READY;
+}
+
+void
+putDebugStr (const char *s)
+{
+ while (*s) {
+ putDebugChar (*s++);
+ }
+}
+
+int
+getDebugChar(void)
+{
+ volatile cbd_t *rbdf;
+ volatile unsigned char *buf;
+ volatile smc_uart_t *up;
+ volatile immap_t *im = (immap_t *)CFG_IMMR;
+ unsigned char c;
+
+ up = (smc_uart_t *)&(im->im_dprambase[KGDB_PROFF_SMC]);
+
+ rbdf = (cbd_t *)&im->im_dprambase[up->smc_rbase];
+
+ /* Wait for character to show up.
+ */
+ buf = (unsigned char *)rbdf->cbd_bufaddr;
+ while (rbdf->cbd_sc & BD_SC_EMPTY)
+ ;
+ c = *buf;
+ rbdf->cbd_sc |= BD_SC_EMPTY;
+
+ return(c);
+}
+
+void
+kgdb_interruptible(int yes)
+{
+ return;
+}
+
+#endif /* CONFIG_KGDB_ON_SMC */
diff --git a/cpu/mpc8260/speed.c b/cpu/mpc8260/speed.c
new file mode 100644
index 0000000..2bf2c4a
--- /dev/null
+++ b/cpu/mpc8260/speed.c
@@ -0,0 +1,211 @@
+/*
+ * (C) Copyright 2000-2002
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <mpc8260.h>
+#include <asm/processor.h>
+
+/* ------------------------------------------------------------------------- */
+
+/* Bus-to-Core Multiplier */
+#define _1x 2
+#define _1_5x 3
+#define _2x 4
+#define _2_5x 5
+#define _3x 6
+#define _3_5x 7
+#define _4x 8
+#define _4_5x 9
+#define _5x 10
+#define _5_5x 11
+#define _6x 12
+#define _6_5x 13
+#define _7x 14
+#define _7_5x 15
+#define _8x 16
+#define _byp -1
+#define _off -2
+#define _unk -3
+
+typedef struct {
+ int b2c_mult;
+ int vco_div;
+ char *freq_60x;
+ char *freq_core;
+} corecnf_t;
+
+/*
+ * this table based on "Errata to MPC8260 PowerQUICC II User's Manual",
+ * Rev. 1, 8/2000, page 10.
+ */
+corecnf_t corecnf_tab[] = {
+ { _1_5x, 4, " 33-100", " 33-100" }, /* 0x00 */
+ { _1x, 4, " 50-150", " 50-150" }, /* 0x01 */
+ { _1x, 8, " 25-75 ", " 25-75 " }, /* 0x02 */
+ { _byp, -1, " ?-? ", " ?-? " }, /* 0x03 */
+ { _2x, 2, " 50-150", "100-300" }, /* 0x04 */
+ { _2x, 4, " 25-75 ", " 50-150" }, /* 0x05 */
+ { _2_5x, 2, " 40-120", "100-240" }, /* 0x06 */
+ { _4_5x, 2, " 22-65 ", "100-300" }, /* 0x07 */
+ { _3x, 2, " 33-100", "100-300" }, /* 0x08 */
+ { _5_5x, 2, " 18-55 ", "100-300" }, /* 0x09 */
+ { _4x, 2, " 25-75 ", "100-300" }, /* 0x0A */
+ { _5x, 2, " 20-60 ", "100-300" }, /* 0x0B */
+ { _1_5x, 8, " 16-50 ", " 16-50 " }, /* 0x0C */
+ { _6x, 2, " 16-50 ", "100-300" }, /* 0x0D */
+ { _3_5x, 2, " 30-85 ", "100-300" }, /* 0x0E */
+ { _off, -1, " ?-? ", " ?-? " }, /* 0x0F */
+ { _3x, 4, " 16-50 ", " 50-150" }, /* 0x10 */
+ { _2_5x, 4, " 20-60 ", " 50-120" }, /* 0x11 */
+ { _6_5x, 2, " 15-46 ", "100-300" }, /* 0x12 */
+ { _byp, -1, " ?-? ", " ?-? " }, /* 0x13 */
+ { _7x, 2, " 14-43 ", "100-300" }, /* 0x14 */
+ { _2x, 4, " 25-75 ", " 50-150" }, /* 0x15 */
+ { _7_5x, 2, " 13-40 ", "100-300" }, /* 0x16 */
+ { _4_5x, 2, " 22-65 ", "100-300" }, /* 0x17 */
+ { _unk, -1, " ?-? ", " ?-? " }, /* 0x18 */
+ { _5_5x, 2, " 18-55 ", "100-300" }, /* 0x19 */
+ { _4x, 2, " 25-75 ", "100-300" }, /* 0x1A */
+ { _5x, 2, " 20-60 ", "100-300" }, /* 0x1B */
+ { _8x, 2, " 12-38 ", "100-300" }, /* 0x1C */
+ { _6x, 2, " 16-50 ", "100-300" }, /* 0x1D */
+ { _3_5x, 2, " 30-85 ", "100-300" }, /* 0x1E */
+ { _off, -1, " ?-? ", " ?-? " }, /* 0x1F */
+};
+
+/* ------------------------------------------------------------------------- */
+
+/*
+ *
+ */
+
+int get_clocks (void)
+{
+ DECLARE_GLOBAL_DATA_PTR;
+
+ volatile immap_t *immap = (immap_t *) CFG_IMMR;
+ ulong clkin;
+ ulong sccr, dfbrg;
+ ulong scmr, corecnf, busdf, cpmdf, plldf, pllmf;
+ corecnf_t *cp;
+
+#if !defined(CONFIG_8260_CLKIN)
+#error clock measuring not implemented yet - define CONFIG_8260_CLKIN
+#else
+ clkin = CONFIG_8260_CLKIN;
+#endif
+
+ sccr = immap->im_clkrst.car_sccr;
+ dfbrg = (sccr & SCCR_DFBRG_MSK) >> SCCR_DFBRG_SHIFT;
+
+ scmr = immap->im_clkrst.car_scmr;
+ corecnf = (scmr & SCMR_CORECNF_MSK) >> SCMR_CORECNF_SHIFT;
+ busdf = (scmr & SCMR_BUSDF_MSK) >> SCMR_BUSDF_SHIFT;
+ cpmdf = (scmr & SCMR_CPMDF_MSK) >> SCMR_CPMDF_SHIFT;
+ plldf = (scmr & SCMR_PLLDF) ? 1 : 0;
+ pllmf = (scmr & SCMR_PLLMF_MSK) >> SCMR_PLLMF_SHIFT;
+
+ cp = &corecnf_tab[corecnf];
+
+ gd->vco_out = (clkin * 2 * (pllmf + 1)) / (plldf + 1);
+
+#if 0
+ if (gd->vco_out / (busdf + 1) != clkin) {
+ /* aaarrrggghhh!!! */
+ return (1);
+ }
+#endif
+
+ gd->cpm_clk = gd->vco_out / 2;
+ gd->bus_clk = clkin;
+ gd->scc_clk = gd->vco_out / 4;
+ gd->brg_clk = gd->vco_out / (1 << (2 * (dfbrg + 1)));
+
+ if (cp->b2c_mult > 0) {
+ gd->cpu_clk = (clkin * cp->b2c_mult) / 2;
+ } else {
+ gd->cpu_clk = clkin;
+ }
+
+ return (0);
+}
+
+int prt_8260_clks (void)
+{
+ DECLARE_GLOBAL_DATA_PTR;
+
+ volatile immap_t *immap = (immap_t *) CFG_IMMR;
+ ulong sccr, dfbrg;
+ ulong scmr, corecnf, busdf, cpmdf, plldf, pllmf;
+ corecnf_t *cp;
+
+ sccr = immap->im_clkrst.car_sccr;
+ dfbrg = (sccr & SCCR_DFBRG_MSK) >> SCCR_DFBRG_SHIFT;
+
+ scmr = immap->im_clkrst.car_scmr;
+ corecnf = (scmr & SCMR_CORECNF_MSK) >> SCMR_CORECNF_SHIFT;
+ busdf = (scmr & SCMR_BUSDF_MSK) >> SCMR_BUSDF_SHIFT;
+ cpmdf = (scmr & SCMR_CPMDF_MSK) >> SCMR_CPMDF_SHIFT;
+ plldf = (scmr & SCMR_PLLDF) ? 1 : 0;
+ pllmf = (scmr & SCMR_PLLMF_MSK) >> SCMR_PLLMF_SHIFT;
+
+ cp = &corecnf_tab[corecnf];
+
+ printf ("MPC8260 Clock Configuration\n - Bus-to-Core Mult ");
+
+ switch (cp->b2c_mult) {
+ case _byp:
+ printf ("BYPASS");
+ break;
+
+ case _off:
+ printf ("OFF");
+ break;
+
+ case _unk:
+ printf ("UNKNOWN");
+ break;
+
+ default:
+ printf ("%d%sx",
+ cp->b2c_mult / 2,
+ (cp->b2c_mult % 2) ? ".5" : "");
+ break;
+ }
+
+ printf (", VCO Div %d, 60x Bus Freq %s, Core Freq %s\n",
+ cp->vco_div, cp->freq_60x, cp->freq_core);
+
+ printf (" - dfbrg %ld, corecnf 0x%02lx, busdf %ld, cpmdf %ld, "
+ "plldf %ld, pllmf %ld\n", dfbrg, corecnf, busdf, cpmdf, plldf,
+ pllmf);
+
+ printf (" - vco_out %10ld, scc_clk %10ld, brg_clk %10ld\n",
+ gd->vco_out, gd->scc_clk, gd->brg_clk);
+
+ printf (" - cpu_clk %10ld, cpm_clk %10ld, bus_clk %10ld\n\n",
+ gd->cpu_clk, gd->cpm_clk, gd->bus_clk);
+ return (0);
+}
+
+/* ------------------------------------------------------------------------- */
diff --git a/cpu/mpc8xx/cpu_init.c b/cpu/mpc8xx/cpu_init.c
new file mode 100644
index 0000000..abe6209
--- /dev/null
+++ b/cpu/mpc8xx/cpu_init.c
@@ -0,0 +1,262 @@
+/*
+ * (C) Copyright 2000-2002
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <watchdog.h>
+
+#include <mpc8xx.h>
+#include <commproc.h>
+
+#if defined(CFG_I2C_UCODE_PATCH) || defined(CFG_SPI_UCODE_PATCH)
+void cpm_load_patch (volatile immap_t * immr);
+#endif
+
+/*
+ * Breath some life into the CPU...
+ *
+ * Set up the memory map,
+ * initialize a bunch of registers,
+ * initialize the UPM's
+ */
+void cpu_init_f (volatile immap_t * immr)
+{
+#ifndef CONFIG_MBX
+ volatile memctl8xx_t *memctl = &immr->im_memctl;
+ ulong reg;
+#endif
+
+ /* SYPCR - contains watchdog control (11-9) */
+
+ immr->im_siu_conf.sc_sypcr = CFG_SYPCR;
+
+#if defined(CONFIG_WATCHDOG)
+ reset_8xx_watchdog (immr);
+#endif /* CONFIG_WATCHDOG */
+
+ /* SIUMCR - contains debug pin configuration (11-6) */
+
+ immr->im_siu_conf.sc_siumcr |= CFG_SIUMCR;
+
+ /* initialize timebase status and control register (11-26) */
+ /* unlock TBSCRK */
+
+ immr->im_sitk.sitk_tbscrk = KAPWR_KEY;
+ immr->im_sit.sit_tbscr = CFG_TBSCR;
+
+ /* initialize the PIT (11-31) */
+
+ immr->im_sitk.sitk_piscrk = KAPWR_KEY;
+ immr->im_sit.sit_piscr = CFG_PISCR;
+
+ /* PLL (CPU clock) settings (15-30) */
+
+ immr->im_clkrstk.cark_plprcrk = KAPWR_KEY;
+
+#ifndef CONFIG_MBX /* MBX board does things different */
+
+ /* If CFG_PLPRCR (set in the various *_config.h files) tries to
+ * set the MF field, then just copy CFG_PLPRCR over car_plprcr,
+ * otherwise OR in CFG_PLPRCR so we do not change the currentMF
+ * field value.
+ */
+#if ((CFG_PLPRCR & PLPRCR_MF_MSK) != 0)
+ reg = CFG_PLPRCR; /* reset control bits */
+#else
+ reg = immr->im_clkrst.car_plprcr;
+ reg &= PLPRCR_MF_MSK; /* isolate MF field */
+ reg |= CFG_PLPRCR; /* reset control bits */
+#endif
+ immr->im_clkrst.car_plprcr = reg;
+
+ /* System integration timers. Don't change EBDF! (15-27) */
+
+ immr->im_clkrstk.cark_sccrk = KAPWR_KEY;
+ reg = immr->im_clkrst.car_sccr;
+ reg &= SCCR_MASK;
+ reg |= CFG_SCCR;
+ immr->im_clkrst.car_sccr = reg;
+
+ /*
+ * Memory Controller:
+ */
+
+ /* perform BR0 reset that MPC850 Rev. A can't guarantee */
+ reg = memctl->memc_br0;
+ reg &= BR_PS_MSK; /* Clear everything except Port Size bits */
+ reg |= BR_V; /* then add just the "Bank Valid" bit */
+ memctl->memc_br0 = reg;
+
+ /* Map banks 0 (and maybe 1) to the FLASH banks 0 (and 1) at
+ * preliminary addresses - these have to be modified later
+ * when FLASH size has been determined
+ *
+ * Depending on the size of the memory region defined by
+ * CFG_OR0_REMAP some boards (wide address mask) allow to map the
+ * CFG_MONITOR_BASE, while others (narrower address mask) can't
+ * map CFG_MONITOR_BASE.
+ *
+ * For example, for CONFIG_IVMS8, the CFG_MONITOR_BASE is
+ * 0xff000000, but CFG_OR0_REMAP's address mask is 0xfff80000.
+ *
+ * If BR0 wasn't loaded with address base 0xff000000, then BR0's
+ * base address remains as 0x00000000. However, the address mask
+ * have been narrowed to 512Kb, so CFG_MONITOR_BASE wasn't mapped
+ * into the Bank0.
+ *
+ * This is why CONFIG_IVMS8 and similar boards must load BR0 with
+ * CFG_BR0_PRELIM in advance.
+ *
+ * [Thanks to Michael Liao for this explanation.
+ * I owe him a free beer. - wd]
+ */
+
+#if defined(CONFIG_GTH) || \
+ defined(CONFIG_HERMES) || \
+ defined(CONFIG_ICU862) || \
+ defined(CONFIG_IP860) || \
+ defined(CONFIG_IVML24) || \
+ defined(CONFIG_IVMS8) || \
+ defined(CONFIG_LWMON) || \
+ defined(CONFIG_MHPC) || \
+ defined(CONFIG_PCU_E) || \
+ defined(CONFIG_R360MPI) || \
+ defined(CONFIG_RPXCLASSIC) || \
+ defined(CONFIG_RPXLITE) || \
+ defined(CONFIG_SPD823TS) || \
+ (defined(CONFIG_MPC860T) && defined(CONFIG_FADS))
+
+ memctl->memc_br0 = CFG_BR0_PRELIM;
+#endif
+
+#if defined(CFG_OR0_REMAP)
+ memctl->memc_or0 = CFG_OR0_REMAP;
+#endif
+#if defined(CFG_OR1_REMAP)
+ memctl->memc_or1 = CFG_OR1_REMAP;
+#endif
+#if defined(CFG_OR5_REMAP)
+ memctl->memc_or5 = CFG_OR5_REMAP;
+#endif
+
+ /* now restrict to preliminary range */
+ memctl->memc_br0 = CFG_BR0_PRELIM;
+ memctl->memc_or0 = CFG_OR0_PRELIM;
+
+#if (defined(CFG_OR1_PRELIM) && defined(CFG_BR1_PRELIM))
+ memctl->memc_or1 = CFG_OR1_PRELIM;
+ memctl->memc_br1 = CFG_BR1_PRELIM;
+#endif
+
+#if defined(CONFIG_IP860) /* disable CS0 now that Flash is mapped on CS1 */
+ memctl->memc_br0 = 0;
+#endif
+
+#if defined(CFG_OR2_PRELIM) && defined(CFG_BR2_PRELIM)
+ memctl->memc_or2 = CFG_OR2_PRELIM;
+ memctl->memc_br2 = CFG_BR2_PRELIM;
+#endif
+
+#if defined(CFG_OR3_PRELIM) && defined(CFG_BR3_PRELIM)
+ memctl->memc_or3 = CFG_OR3_PRELIM;
+ memctl->memc_br3 = CFG_BR3_PRELIM;
+#endif
+
+#if defined(CFG_OR4_PRELIM) && defined(CFG_BR4_PRELIM)
+ memctl->memc_or4 = CFG_OR4_PRELIM;
+ memctl->memc_br4 = CFG_BR4_PRELIM;
+#endif
+
+#if defined(CFG_OR5_PRELIM) && defined(CFG_BR5_PRELIM)
+ memctl->memc_or5 = CFG_OR5_PRELIM;
+ memctl->memc_br5 = CFG_BR5_PRELIM;
+#endif
+
+#if defined(CFG_OR6_PRELIM) && defined(CFG_BR6_PRELIM)
+ memctl->memc_or6 = CFG_OR6_PRELIM;
+ memctl->memc_br6 = CFG_BR6_PRELIM;
+#endif
+
+#if defined(CFG_OR7_PRELIM) && defined(CFG_BR7_PRELIM)
+ memctl->memc_or7 = CFG_OR7_PRELIM;
+ memctl->memc_br7 = CFG_BR7_PRELIM;
+#endif
+
+#endif /* ! CONFIG_MBX */
+
+ /*
+ * Reset CPM
+ */
+ immr->im_cpm.cp_cpcr = CPM_CR_RST | CPM_CR_FLG;
+ do { /* Spin until command processed */
+ __asm__ ("eieio");
+ } while (immr->im_cpm.cp_cpcr & CPM_CR_FLG);
+
+#ifdef CONFIG_MBX
+ /*
+ * on the MBX, things are a little bit different:
+ * - we need to read the VPD to get board information
+ * - the plprcr is set up dynamically
+ * - the memory controller is set up dynamically
+ */
+ mbx_init ();
+#endif /* CONFIG_MBX */
+
+#ifdef CONFIG_RPXCLASSIC
+ rpxclassic_init ();
+#endif
+
+#ifdef CFG_RCCR /* must be done before cpm_load_patch() */
+ /* write config value */
+ immr->im_cpm.cp_rccr = CFG_RCCR;
+#endif
+
+#if defined(CFG_I2C_UCODE_PATCH) || defined(CFG_SPI_UCODE_PATCH)
+ cpm_load_patch (immr); /* load mpc8xx microcode patch */
+#endif
+}
+
+/*
+ * initialize higher level parts of CPU like timers
+ */
+int cpu_init_r (void)
+{
+#if defined(CFG_RTCSC) || defined(CFG_RMDS)
+ DECLARE_GLOBAL_DATA_PTR;
+
+ bd_t *bd = gd->bd;
+ volatile immap_t *immr = (volatile immap_t *) (bd->bi_immr_base);
+#endif
+
+#ifdef CFG_RTCSC
+ /* Unlock RTSC register */
+ immr->im_sitk.sitk_rtcsck = KAPWR_KEY;
+ /* write config value */
+ immr->im_sit.sit_rtcsc = CFG_RTCSC;
+#endif
+
+#ifdef CFG_RMDS
+ /* write config value */
+ immr->im_cpm.cp_rmds = CFG_RMDS;
+#endif
+ return (0);
+}
diff --git a/cpu/mpc8xx/serial.c b/cpu/mpc8xx/serial.c
new file mode 100644
index 0000000..0690300
--- /dev/null
+++ b/cpu/mpc8xx/serial.c
@@ -0,0 +1,640 @@
+/*
+ * (C) Copyright 2000
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <commproc.h>
+#include <command.h>
+
+#if !defined(CONFIG_8xx_CONS_NONE) /* No Console at all */
+
+#if defined(CONFIG_8xx_CONS_SMC1) /* Console on SMC1 */
+#define SMC_INDEX 0
+#undef SCC_INDEX
+#define PROFF_SMC PROFF_SMC1
+#define CPM_CR_CH_SMC CPM_CR_CH_SMC1
+
+#elif defined(CONFIG_8xx_CONS_SMC2) /* Console on SMC2 */
+#define SMC_INDEX 1
+#undef SCC_INDEX
+#define PROFF_SMC PROFF_SMC2
+#define CPM_CR_CH_SMC CPM_CR_CH_SMC2
+
+#elif defined(CONFIG_8xx_CONS_SCC1) /* Console on SCC1 */
+#undef SMC_INDEX
+#define SCC_INDEX 0
+#define PROFF_SCC PROFF_SCC1
+#define CPM_CR_CH_SCC CPM_CR_CH_SCC1
+
+#elif defined(CONFIG_8xx_CONS_SCC2) /* Console on SCC2 */
+#undef SMC_INDEX
+#define SCC_INDEX 1
+#define PROFF_SCC PROFF_SCC2
+#define CPM_CR_CH_SCC CPM_CR_CH_SCC2
+
+#elif defined(CONFIG_8xx_CONS_SCC3) /* Console on SCC3 */
+#undef SMC_INDEX
+#define SCC_INDEX 2
+#define PROFF_SCC PROFF_SCC3
+#define CPM_CR_CH_SCC CPM_CR_CH_SCC3
+
+#elif defined(CONFIG_8xx_CONS_SCC4) /* Console on SCC4 */
+#undef SMC_INDEX
+#define SCC_INDEX 3
+#define PROFF_SCC PROFF_SCC4
+#define CPM_CR_CH_SCC CPM_CR_CH_SCC4
+
+#else /* CONFIG_8xx_CONS_? */
+#error "console not correctly defined"
+#endif
+
+#if (defined (CONFIG_8xx_CONS_SMC1) || defined (CONFIG_8xx_CONS_SMC2))
+
+/*
+ * Minimal serial functions needed to use one of the SMC ports
+ * as serial console interface.
+ */
+
+int serial_init (void)
+{
+ volatile immap_t *im = (immap_t *)CFG_IMMR;
+ volatile smc_t *sp;
+ volatile smc_uart_t *up;
+ volatile cbd_t *tbdf, *rbdf;
+ volatile cpm8xx_t *cp = &(im->im_cpm);
+#if (!defined(CONFIG_8xx_CONS_SMC1)) && (defined(CONFIG_MPC823) || defined(CONFIG_MPC850))
+ volatile iop8xx_t *ip = (iop8xx_t *)&(im->im_ioport);
+#endif
+ uint dpaddr;
+
+ /* initialize pointers to SMC */
+
+ sp = (smc_t *) &(cp->cp_smc[SMC_INDEX]);
+ up = (smc_uart_t *) &cp->cp_dparam[PROFF_SMC];
+
+ /* Disable transmitter/receiver.
+ */
+ sp->smc_smcmr &= ~(SMCMR_REN | SMCMR_TEN);
+
+ /* Enable SDMA.
+ */
+ im->im_siu_conf.sc_sdcr = 1;
+
+ /* clear error conditions */
+#ifdef CFG_SDSR
+ im->im_sdma.sdma_sdsr = CFG_SDSR;
+#else
+ im->im_sdma.sdma_sdsr = 0x83;
+#endif
+
+ /* clear SDMA interrupt mask */
+#ifdef CFG_SDMR
+ im->im_sdma.sdma_sdmr = CFG_SDMR;
+#else
+ im->im_sdma.sdma_sdmr = 0x00;
+#endif
+
+#if defined(CONFIG_8xx_CONS_SMC1)
+ /* Use Port B for SMC1 instead of other functions.
+ */
+ cp->cp_pbpar |= 0x000000c0;
+ cp->cp_pbdir &= ~0x000000c0;
+ cp->cp_pbodr &= ~0x000000c0;
+#else /* CONFIG_8xx_CONS_SMC2 */
+# if defined(CONFIG_MPC823) || defined(CONFIG_MPC850)
+ /* Use Port A for SMC2 instead of other functions.
+ */
+ ip->iop_papar |= 0x00c0;
+ ip->iop_padir &= ~0x00c0;
+ ip->iop_paodr &= ~0x00c0;
+# else /* must be a 860 then */
+ /* Use Port B for SMC2 instead of other functions.
+ */
+ cp->cp_pbpar |= 0x00000c00;
+ cp->cp_pbdir &= ~0x00000c00;
+ cp->cp_pbodr &= ~0x00000c00;
+# endif
+#endif
+
+#if defined(CONFIG_FADS)
+ /* Enable RS232 */
+#if defined(CONFIG_8xx_CONS_SMC1)
+ *((uint *) BCSR1) &= ~BCSR1_RS232EN_1;
+#else
+ *((uint *) BCSR1) &= ~BCSR1_RS232EN_2;
+#endif
+#endif /* CONFIG_FADS */
+
+#if defined(CONFIG_RPXLITE) || defined(CONFIG_RPXCLASSIC)
+ /* Enable Monitor Port Transceiver */
+ *((uchar *) BCSR0) |= BCSR0_ENMONXCVR ;
+#endif /* CONFIG_RPXLITE */
+
+ /* Set the physical address of the host memory buffers in
+ * the buffer descriptors.
+ */
+
+#ifdef CFG_ALLOC_DPRAM
+ dpaddr = dpram_alloc_align (sizeof(cbd_t)*2 + 2, 8) ;
+#else
+ dpaddr = CPM_SERIAL_BASE ;
+#endif
+
+ /* Allocate space for two buffer descriptors in the DP ram.
+ * For now, this address seems OK, but it may have to
+ * change with newer versions of the firmware.
+ * damm: allocating space after the two buffers for rx/tx data
+ */
+
+ rbdf = (cbd_t *)&cp->cp_dpmem[dpaddr];
+ rbdf->cbd_bufaddr = (uint) (rbdf+2);
+ rbdf->cbd_sc = 0;
+ tbdf = rbdf + 1;
+ tbdf->cbd_bufaddr = ((uint) (rbdf+2)) + 1;
+ tbdf->cbd_sc = 0;
+
+ /* Set up the uart parameters in the parameter ram.
+ */
+ up->smc_rbase = dpaddr;
+ up->smc_tbase = dpaddr+sizeof(cbd_t);
+ up->smc_rfcr = SMC_EB;
+ up->smc_tfcr = SMC_EB;
+
+#if defined(CONFIG_MBX)
+ board_serial_init();
+#endif /* CONFIG_MBX */
+
+ /* Set UART mode, 8 bit, no parity, one stop.
+ * Enable receive and transmit.
+ */
+ sp->smc_smcmr = smcr_mk_clen(9) | SMCMR_SM_UART;
+
+ /* Mask all interrupts and remove anything pending.
+ */
+ sp->smc_smcm = 0;
+ sp->smc_smce = 0xff;
+
+ /* Set up the baud rate generator.
+ */
+ serial_setbrg ();
+
+ /* Make the first buffer the only buffer.
+ */
+ tbdf->cbd_sc |= BD_SC_WRAP;
+ rbdf->cbd_sc |= BD_SC_EMPTY | BD_SC_WRAP;
+
+ /* Single character receive.
+ */
+ up->smc_mrblr = 1;
+ up->smc_maxidl = 0;
+
+ /* Initialize Tx/Rx parameters.
+ */
+
+ while (cp->cp_cpcr & CPM_CR_FLG) /* wait if cp is busy */
+ ;
+
+ cp->cp_cpcr = mk_cr_cmd(CPM_CR_CH_SMC, CPM_CR_INIT_TRX) | CPM_CR_FLG;
+
+ while (cp->cp_cpcr & CPM_CR_FLG) /* wait if cp is busy */
+ ;
+
+ /* Enable transmitter/receiver.
+ */
+ sp->smc_smcmr |= SMCMR_REN | SMCMR_TEN;
+
+ return (0);
+}
+
+void
+serial_setbrg (void)
+{
+ DECLARE_GLOBAL_DATA_PTR;
+
+ volatile immap_t *im = (immap_t *)CFG_IMMR;
+ volatile cpm8xx_t *cp = &(im->im_cpm);
+
+ /* Set up the baud rate generator.
+ * See 8xx_io/commproc.c for details.
+ *
+ * Wire BRG1 to SMCx
+ */
+
+ cp->cp_simode = 0x00000000;
+
+ cp->cp_brgc1 =
+ (((gd->cpu_clk / 16 / gd->baudrate)-1) << 1) | CPM_BRG_EN;
+}
+
+void
+serial_putc(const char c)
+{
+ volatile cbd_t *tbdf;
+ volatile char *buf;
+ volatile smc_uart_t *up;
+ volatile immap_t *im = (immap_t *)CFG_IMMR;
+ volatile cpm8xx_t *cpmp = &(im->im_cpm);
+
+ if (c == '\n')
+ serial_putc ('\r');
+
+ up = (smc_uart_t *)&cpmp->cp_dparam[PROFF_SMC];
+
+ tbdf = (cbd_t *)&cpmp->cp_dpmem[up->smc_tbase];
+
+ /* Wait for last character to go.
+ */
+
+ buf = (char *)tbdf->cbd_bufaddr;
+#if 0
+ __asm__("eieio");
+ while (tbdf->cbd_sc & BD_SC_READY)
+ __asm__("eieio");
+#endif
+
+ *buf = c;
+ tbdf->cbd_datlen = 1;
+ tbdf->cbd_sc |= BD_SC_READY;
+ __asm__("eieio");
+#if 1
+ while (tbdf->cbd_sc & BD_SC_READY)
+ __asm__("eieio");
+#endif
+}
+
+int
+serial_getc(void)
+{
+ volatile cbd_t *rbdf;
+ volatile unsigned char *buf;
+ volatile smc_uart_t *up;
+ volatile immap_t *im = (immap_t *)CFG_IMMR;
+ volatile cpm8xx_t *cpmp = &(im->im_cpm);
+ unsigned char c;
+
+ up = (smc_uart_t *)&cpmp->cp_dparam[PROFF_SMC];
+
+ rbdf = (cbd_t *)&cpmp->cp_dpmem[up->smc_rbase];
+
+ /* Wait for character to show up.
+ */
+ buf = (unsigned char *)rbdf->cbd_bufaddr;
+ while (rbdf->cbd_sc & BD_SC_EMPTY)
+ ;
+ c = *buf;
+ rbdf->cbd_sc |= BD_SC_EMPTY;
+
+ return(c);
+}
+
+int
+serial_tstc()
+{
+ volatile cbd_t *rbdf;
+ volatile smc_uart_t *up;
+ volatile immap_t *im = (immap_t *)CFG_IMMR;
+ volatile cpm8xx_t *cpmp = &(im->im_cpm);
+
+ up = (smc_uart_t *)&cpmp->cp_dparam[PROFF_SMC];
+
+ rbdf = (cbd_t *)&cpmp->cp_dpmem[up->smc_rbase];
+
+ return(!(rbdf->cbd_sc & BD_SC_EMPTY));
+}
+
+#else /* ! CONFIG_8xx_CONS_SMC1, CONFIG_8xx_CONS_SMC2 */
+
+int serial_init (void)
+{
+ volatile immap_t *im = (immap_t *)CFG_IMMR;
+ volatile scc_t *sp;
+ volatile scc_uart_t *up;
+ volatile cbd_t *tbdf, *rbdf;
+ volatile cpm8xx_t *cp = &(im->im_cpm);
+ uint dpaddr;
+#if (SCC_INDEX != 2) || !defined(CONFIG_MPC850)
+ volatile iop8xx_t *ip = (iop8xx_t *)&(im->im_ioport);
+#endif
+
+ /* initialize pointers to SCC */
+
+ sp = (scc_t *) &(cp->cp_scc[SCC_INDEX]);
+ up = (scc_uart_t *) &cp->cp_dparam[PROFF_SCC];
+
+#if defined(CONFIG_LWMON) && defined(CONFIG_8xx_CONS_SCC2)
+ { /* Disable Ethernet, enable Serial */
+ uchar c;
+
+ c = pic_read (0x61);
+ c &= ~0x40; /* enable COM3 */
+ c |= 0x80; /* disable Ethernet */
+ pic_write (0x61, c);
+
+ /* enable RTS2 */
+ cp->cp_pbpar |= 0x2000;
+ cp->cp_pbdat |= 0x2000;
+ cp->cp_pbdir |= 0x2000;
+ }
+#endif /* CONFIG_LWMON */
+
+ /* Disable transmitter/receiver.
+ */
+ sp->scc_gsmrl &= ~(SCC_GSMRL_ENR | SCC_GSMRL_ENT);
+
+#if (SCC_INDEX == 2) && defined(CONFIG_MPC850)
+ /*
+ * The MPC850 has SCC3 on Port B
+ */
+ cp->cp_pbpar |= 0x06;
+ cp->cp_pbdir &= ~0x06;
+ cp->cp_pbodr &= ~0x06;
+
+#elif (SCC_INDEX < 2) || !defined(CONFIG_IP860)
+ /*
+ * Standard configuration for SCC's is on Part A
+ */
+ ip->iop_papar |= ((3 << (2 * SCC_INDEX)));
+ ip->iop_padir &= ~((3 << (2 * SCC_INDEX)));
+ ip->iop_paodr &= ~((3 << (2 * SCC_INDEX)));
+#else
+ /*
+ * The IP860 has SCC3 and SCC4 on Port D
+ */
+ ip->iop_pdpar |= ((3 << (2 * SCC_INDEX)));
+#endif
+
+ /* Allocate space for two buffer descriptors in the DP ram.
+ */
+
+#ifdef CFG_ALLOC_DPRAM
+ dpaddr = dpram_alloc_align (sizeof(cbd_t)*2 + 2, 8) ;
+#else
+ dpaddr = CPM_SERIAL_BASE ;
+#endif
+
+ /* Enable SDMA.
+ */
+ im->im_siu_conf.sc_sdcr = 0x0001;
+
+ /* Set the physical address of the host memory buffers in
+ * the buffer descriptors.
+ */
+
+ rbdf = (cbd_t *)&cp->cp_dpmem[dpaddr];
+ rbdf->cbd_bufaddr = (uint) (rbdf+2);
+ rbdf->cbd_sc = 0;
+ tbdf = rbdf + 1;
+ tbdf->cbd_bufaddr = ((uint) (rbdf+2)) + 1;
+ tbdf->cbd_sc = 0;
+
+ /* Set up the baud rate generator.
+ */
+ serial_setbrg ();
+
+ /* Set up the uart parameters in the parameter ram.
+ */
+ up->scc_genscc.scc_rbase = dpaddr;
+ up->scc_genscc.scc_tbase = dpaddr+sizeof(cbd_t);
+
+ /* Initialize Tx/Rx parameters.
+ */
+ while (cp->cp_cpcr & CPM_CR_FLG) /* wait if cp is busy */
+ ;
+ cp->cp_cpcr = mk_cr_cmd(CPM_CR_CH_SCC, CPM_CR_INIT_TRX) | CPM_CR_FLG;
+
+ while (cp->cp_cpcr & CPM_CR_FLG) /* wait if cp is busy */
+ ;
+
+ up->scc_genscc.scc_rfcr = SCC_EB | 0x05;
+ up->scc_genscc.scc_tfcr = SCC_EB | 0x05;
+
+ up->scc_genscc.scc_mrblr = 1; /* Single character receive */
+ up->scc_maxidl = 0; /* disable max idle */
+ up->scc_brkcr = 1; /* send one break character on stop TX */
+ up->scc_parec = 0;
+ up->scc_frmec = 0;
+ up->scc_nosec = 0;
+ up->scc_brkec = 0;
+ up->scc_uaddr1 = 0;
+ up->scc_uaddr2 = 0;
+ up->scc_toseq = 0;
+ up->scc_char1 = 0x8000;
+ up->scc_char2 = 0x8000;
+ up->scc_char3 = 0x8000;
+ up->scc_char4 = 0x8000;
+ up->scc_char5 = 0x8000;
+ up->scc_char6 = 0x8000;
+ up->scc_char7 = 0x8000;
+ up->scc_char8 = 0x8000;
+ up->scc_rccm = 0xc0ff;
+
+ /* Set low latency / small fifo.
+ */
+ sp->scc_gsmrh = SCC_GSMRH_RFW;
+
+ /* Set SCC(x) clock mode to 16x
+ * See 8xx_io/commproc.c for details.
+ *
+ * Wire BRG1 to SCCn
+ */
+
+ /* Set UART mode, clock divider 16 on Tx and Rx
+ */
+ sp->scc_gsmrl |=
+ (SCC_GSMRL_MODE_UART | SCC_GSMRL_TDCR_16 | SCC_GSMRL_RDCR_16);
+
+ sp->scc_psmr |= SCU_PSMR_CL;
+
+ /* Mask all interrupts and remove anything pending.
+ */
+ sp->scc_sccm = 0;
+ sp->scc_scce = 0xffff;
+ sp->scc_dsr = 0x7e7e;
+ sp->scc_psmr = 0x3000;
+
+ /* Make the first buffer the only buffer.
+ */
+ tbdf->cbd_sc |= BD_SC_WRAP;
+ rbdf->cbd_sc |= BD_SC_EMPTY | BD_SC_WRAP;
+
+ /* Enable transmitter/receiver.
+ */
+ sp->scc_gsmrl |= (SCC_GSMRL_ENR | SCC_GSMRL_ENT);
+
+ return (0);
+}
+
+void
+serial_setbrg (void)
+{
+ DECLARE_GLOBAL_DATA_PTR;
+
+ volatile immap_t *im = (immap_t *)CFG_IMMR;
+ volatile cpm8xx_t *cp = &(im->im_cpm);
+
+ /* Set up the baud rate generator.
+ * See 8xx_io/commproc.c for details.
+ *
+ * Wire BRG1 to SCCx
+ */
+
+ cp->cp_sicr &= ~(0x000000FF << (8 * SCC_INDEX));
+ /* no |= needed, since BRG1 is 000 */
+
+ cp->cp_brgc1 =
+ (((gd->cpu_clk / 16 / gd->baudrate)-1) << 1) | CPM_BRG_EN;
+}
+
+void
+serial_putc(const char c)
+{
+ volatile cbd_t *tbdf;
+ volatile char *buf;
+ volatile scc_uart_t *up;
+ volatile immap_t *im = (immap_t *)CFG_IMMR;
+ volatile cpm8xx_t *cpmp = &(im->im_cpm);
+
+ if (c == '\n')
+ serial_putc ('\r');
+
+ up = (scc_uart_t *)&cpmp->cp_dparam[PROFF_SCC];
+
+ tbdf = (cbd_t *)&cpmp->cp_dpmem[up->scc_genscc.scc_tbase];
+
+ /* Wait for last character to go.
+ */
+
+ buf = (char *)tbdf->cbd_bufaddr;
+#if 0
+ __asm__("eieio");
+ while (tbdf->cbd_sc & BD_SC_READY)
+ __asm__("eieio");
+#endif
+
+ *buf = c;
+ tbdf->cbd_datlen = 1;
+ tbdf->cbd_sc |= BD_SC_READY;
+ __asm__("eieio");
+#if 1
+ while (tbdf->cbd_sc & BD_SC_READY)
+ __asm__("eieio");
+#endif
+}
+
+int
+serial_getc(void)
+{
+ volatile cbd_t *rbdf;
+ volatile unsigned char *buf;
+ volatile scc_uart_t *up;
+ volatile immap_t *im = (immap_t *)CFG_IMMR;
+ volatile cpm8xx_t *cpmp = &(im->im_cpm);
+ unsigned char c;
+
+ up = (scc_uart_t *)&cpmp->cp_dparam[PROFF_SCC];
+
+ rbdf = (cbd_t *)&cpmp->cp_dpmem[up->scc_genscc.scc_rbase];
+
+ /* Wait for character to show up.
+ */
+ buf = (unsigned char *)rbdf->cbd_bufaddr;
+ while (rbdf->cbd_sc & BD_SC_EMPTY)
+ ;
+ c = *buf;
+ rbdf->cbd_sc |= BD_SC_EMPTY;
+
+ return(c);
+}
+
+int
+serial_tstc()
+{
+ volatile cbd_t *rbdf;
+ volatile scc_uart_t *up;
+ volatile immap_t *im = (immap_t *)CFG_IMMR;
+ volatile cpm8xx_t *cpmp = &(im->im_cpm);
+
+ up = (scc_uart_t *)&cpmp->cp_dparam[PROFF_SCC];
+
+ rbdf = (cbd_t *)&cpmp->cp_dpmem[up->scc_genscc.scc_rbase];
+
+ return(!(rbdf->cbd_sc & BD_SC_EMPTY));
+}
+
+#endif /* CONFIG_8xx_CONS_SMC1, CONFIG_8xx_CONS_SMC2 */
+
+
+void
+serial_puts (const char *s)
+{
+ while (*s) {
+ serial_putc (*s++);
+ }
+}
+
+
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+
+void
+kgdb_serial_init(void)
+{
+#if defined(CONFIG_8xx_CONS_SMC1)
+ serial_printf("[on SMC1] ");
+#elif defined(CONFIG_8xx_CONS_SMC2)
+ serial_printf("[on SMC2] ");
+#elif defined(CONFIG_8xx_CONS_SCC1)
+ serial_printf("[on SCC1] ");
+#elif defined(CONFIG_8xx_CONS_SCC2)
+ serial_printf("[on SCC2] ");
+#elif defined(CONFIG_8xx_CONS_SCC3)
+ serial_printf("[on SCC3] ");
+#elif defined(CONFIG_8xx_CONS_SCC4)
+ serial_printf("[on SCC4] ");
+#endif
+}
+
+void
+putDebugChar (int c)
+{
+ serial_putc (c);
+}
+
+void
+putDebugStr (const char *str)
+{
+ serial_puts (str);
+}
+
+int
+getDebugChar (void)
+{
+ return serial_getc();
+}
+
+void
+kgdb_interruptible (int yes)
+{
+ return;
+}
+#endif /* CFG_CMD_KGDB */
+
+#endif /* CONFIG_8xx_CONS_NONE */
diff --git a/cpu/mpc8xx/speed.c b/cpu/mpc8xx/speed.c
new file mode 100644
index 0000000..ef32371
--- /dev/null
+++ b/cpu/mpc8xx/speed.c
@@ -0,0 +1,187 @@
+/*
+ * (C) Copyright 2000-2002
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <mpc8xx.h>
+#include <asm/processor.h>
+
+#define PITC_SHIFT 16
+#define PITR_SHIFT 16
+/* pitc values to time for 58/8192 seconds (about 70.8 milliseconds) */
+#define SPEED_PIT_COUNTS 58
+#define SPEED_PITC ((SPEED_PIT_COUNTS - 1) << PITC_SHIFT)
+#define SPEED_PITC_INIT ((SPEED_PIT_COUNTS + 1) << PITC_SHIFT)
+
+#if !defined(CONFIG_8xx_GCLK_FREQ)
+/* Access functions for the Machine State Register */
+static __inline__ unsigned long get_msr(void)
+{
+ unsigned long msr;
+
+ asm volatile("mfmsr %0" : "=r" (msr) :);
+ return msr;
+}
+
+static __inline__ void set_msr(unsigned long msr)
+{
+ asm volatile("mtmsr %0" : : "r" (msr));
+}
+#endif
+
+/* ------------------------------------------------------------------------- */
+
+/*
+ * Measure CPU clock speed (core clock GCLK1, GCLK2),
+ * also determine bus clock speed (checking bus divider factor)
+ *
+ * (Approx. GCLK frequency in Hz)
+ *
+ * Initializes timer 2 and PIT, but disables them before return.
+ * [Use timer 2, because MPC823 CPUs mask 0.x do not have timers 3 and 4]
+ *
+ * When measuring the CPU clock against the PIT, we count cpu clocks
+ * for 58/8192 seconds with a prescale divide by 177 for the cpu clock.
+ * These strange values for the timing interval and prescaling are used
+ * because the formula for the CPU clock is:
+ *
+ * CPU clock = count * (177 * (8192 / 58))
+ *
+ * = count * 24999.7241
+ *
+ * which is very close to
+ *
+ * = count * 25000
+ *
+ * Since the count gives the CPU clock divided by 25000, we can get
+ * the CPU clock rounded to the nearest 0.1 MHz by
+ *
+ * CPU clock = ((count + 2) / 4) * 100000;
+ *
+ * The rounding is important since the measurement is sometimes going
+ * to be high or low by 0.025 MHz, depending on exactly how the clocks
+ * and counters interact. By rounding we get the exact answer for any
+ * CPU clock that is an even multiple of 0.1 MHz.
+ */
+
+int get_clocks (void)
+{
+ DECLARE_GLOBAL_DATA_PTR;
+
+ volatile immap_t *immr = (immap_t *) CFG_IMMR;
+#ifndef CONFIG_8xx_GCLK_FREQ
+ volatile cpmtimer8xx_t *timerp = &immr->im_cpmtimer;
+ ulong timer2_val;
+ ulong msr_val;
+
+ /* Reset + Stop Timer 2, no cascading
+ */
+ timerp->cpmt_tgcr &= ~(TGCR_CAS2 | TGCR_RST2);
+
+ /* Keep stopped, halt in debug mode
+ */
+ timerp->cpmt_tgcr |= (TGCR_FRZ2 | TGCR_STP2);
+
+ /* Timer 2 setup:
+ * Output ref. interrupt disable, int. clock
+ * Prescale by 177. Note that prescaler divides by value + 1
+ * so we must subtract 1 here.
+ */
+ timerp->cpmt_tmr2 = ((177 - 1) << TMR_PS_SHIFT) | TMR_ICLK_IN_GEN;
+
+ timerp->cpmt_tcn2 = 0; /* reset state */
+ timerp->cpmt_tgcr |= TGCR_RST2; /* enable timer 2 */
+
+ /*
+ * PIT setup:
+ *
+ * We want to time for SPEED_PITC_COUNTS counts (of 8192 Hz),
+ * so the count value would be SPEED_PITC_COUNTS - 1.
+ * But there would be an uncertainty in the start time of 1/4
+ * count since when we enable the PIT the count is not
+ * synchronized to the 32768 Hz oscillator. The trick here is
+ * to start the count higher and wait until the PIT count
+ * changes to the required value before starting timer 2.
+ *
+ * One count high should be enough, but occasionally the start
+ * is off by 1 or 2 counts of 32768 Hz. With the start value
+ * set two counts high it seems very reliable.
+ */
+
+ immr->im_sitk.sitk_pitck = KAPWR_KEY; /* PIT initialization */
+ immr->im_sit.sit_pitc = SPEED_PITC_INIT;
+
+ immr->im_sitk.sitk_piscrk = KAPWR_KEY;
+ immr->im_sit.sit_piscr = CFG_PISCR;
+
+ /*
+ * Start measurement - disable interrupts, just in case
+ */
+ msr_val = get_msr ();
+ set_msr (msr_val & ~MSR_EE);
+
+ immr->im_sit.sit_piscr |= PISCR_PTE;
+
+ /* spin until get exact count when we want to start */
+ while (immr->im_sit.sit_pitr > SPEED_PITC);
+
+ timerp->cpmt_tgcr &= ~TGCR_STP2; /* Start Timer 2 */
+ while ((immr->im_sit.sit_piscr & PISCR_PS) == 0);
+ timerp->cpmt_tgcr |= TGCR_STP2; /* Stop Timer 2 */
+
+ /* re-enable external interrupts if they were on */
+ set_msr (msr_val);
+
+ /* Disable timer and PIT
+ */
+ timer2_val = timerp->cpmt_tcn2; /* save before reset timer */
+
+ timerp->cpmt_tgcr &= ~(TGCR_RST2 | TGCR_FRZ2 | TGCR_STP2);
+ immr->im_sit.sit_piscr &= ~PISCR_PTE;
+
+ gd->cpu_clk = ((timer2_val + 2) / 4) * 100000L; /* convert to Hz */
+
+#else /* CONFIG_8xx_GCLK_FREQ */
+
+ /*
+ * If for some reason measuring the gclk frequency won't
+ * work, we return the hardwired value.
+ * (For example, the cogent CMA286-60 CPU module has no
+ * separate oscillator for PITRTCLK)
+ */
+
+ gd->cpu_clk = CONFIG_8xx_GCLK_FREQ;
+
+#endif /* CONFIG_8xx_GCLK_FREQ */
+
+ if ((immr->im_clkrst.car_sccr & SCCR_EBDF11) == 0) {
+ /* No Bus Divider active */
+ gd->bus_clk = gd->cpu_clk;
+ } else {
+ /* The MPC8xx has only one BDF: half clock speed */
+ gd->bus_clk = gd->cpu_clk / 2;
+ }
+
+ return (0);
+}
+
+/* ------------------------------------------------------------------------- */
diff --git a/cpu/mpc8xx/wlkbd.c b/cpu/mpc8xx/wlkbd.c
new file mode 100644
index 0000000..13009e2
--- /dev/null
+++ b/cpu/mpc8xx/wlkbd.c
@@ -0,0 +1,36 @@
+/*
+ * (C) Copyright 2000
+ * Paolo Scaffardi, AIRVENT SAM s.p.a - RIMINI(ITALY), arsenio@tin.it
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <config.h>
+
+#ifdef CONFIG_WL_4PPM_KEYBOARD
+
+/* WIP: Wireless keyboard on SMC
+ */
+int drv_wlkbd_init (void)
+{
+ return 0 ;
+}
+
+#endif /* CONFIG_WL_4PPM_KEYBOARD */
diff --git a/cpu/ppc4xx/cpu_init.c b/cpu/ppc4xx/cpu_init.c
new file mode 100644
index 0000000..52d4650
--- /dev/null
+++ b/cpu/ppc4xx/cpu_init.c
@@ -0,0 +1,148 @@
+/*
+ * (C) Copyright 2000
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <watchdog.h>
+#include <405gp_enet.h>
+#include <asm/processor.h>
+#include <ppc4xx.h>
+
+
+#define mtebc(reg, data) mtdcr(ebccfga,reg);mtdcr(ebccfgd,data)
+
+
+/*
+ * Breath some life into the CPU...
+ *
+ * Set up the memory map,
+ * initialize a bunch of registers
+ */
+void
+cpu_init_f (void)
+{
+ /*
+ * External Bus Controller (EBC) Setup
+ */
+#if (defined(CFG_EBC_PB0AP) && defined(CFG_EBC_PB0CR))
+ /*
+ * Move the next instructions into icache, since these modify the flash
+ * we are running from!
+ */
+ asm volatile(" bl 0f" ::: "lr");
+ asm volatile("0: mflr 3" ::: "r3");
+ asm volatile(" addi 4, 0, 14" ::: "r4");
+ asm volatile(" mtctr 4" ::: "ctr");
+ asm volatile("1: icbt 0, 3");
+ asm volatile(" addi 3, 3, 32" ::: "r3");
+ asm volatile(" bdnz 1b" ::: "ctr", "cr0");
+ asm volatile(" addis 3, 0, 0x0" ::: "r3");
+ asm volatile(" ori 3, 3, 0xA000" ::: "r3");
+ asm volatile(" mtctr 3" ::: "ctr");
+ asm volatile("2: bdnz 2b" ::: "ctr", "cr0");
+
+ mtebc(pb0ap, CFG_EBC_PB0AP);
+ mtebc(pb0cr, CFG_EBC_PB0CR);
+#endif
+
+#if (defined(CFG_EBC_PB1AP) && defined(CFG_EBC_PB1CR))
+ mtebc(pb1ap, CFG_EBC_PB1AP);
+ mtebc(pb1cr, CFG_EBC_PB1CR);
+#endif
+
+#if (defined(CFG_EBC_PB2AP) && defined(CFG_EBC_PB2CR))
+ mtebc(pb2ap, CFG_EBC_PB2AP);
+ mtebc(pb2cr, CFG_EBC_PB2CR);
+#endif
+
+#if (defined(CFG_EBC_PB3AP) && defined(CFG_EBC_PB3CR))
+ mtebc(pb3ap, CFG_EBC_PB3AP);
+ mtebc(pb3cr, CFG_EBC_PB3CR);
+#endif
+
+#if (defined(CFG_EBC_PB4AP) && defined(CFG_EBC_PB4CR))
+ mtebc(pb4ap, CFG_EBC_PB4AP);
+ mtebc(pb4cr, CFG_EBC_PB4CR);
+#endif
+
+#if (defined(CFG_EBC_PB5AP) && defined(CFG_EBC_PB5CR))
+ mtebc(pb5ap, CFG_EBC_PB5AP);
+ mtebc(pb5cr, CFG_EBC_PB5CR);
+#endif
+
+#if (defined(CFG_EBC_PB6AP) && defined(CFG_EBC_PB6CR))
+ mtebc(pb6ap, CFG_EBC_PB6AP);
+ mtebc(pb6cr, CFG_EBC_PB6CR);
+#endif
+
+#if (defined(CFG_EBC_PB7AP) && defined(CFG_EBC_PB7CR))
+ mtebc(pb7ap, CFG_EBC_PB7AP);
+ mtebc(pb7cr, CFG_EBC_PB7CR);
+#endif
+
+#if defined(CONFIG_WATCHDOG)
+ unsigned long val;
+
+ val = mfspr(tcr);
+ val |= 0xf0000000; /* generate system reset after 2.684 seconds */
+ mtspr(tcr, val);
+
+ val = mfspr(tsr);
+ val |= 0x80000000; /* enable watchdog timer */
+ mtspr(tsr, val);
+
+ reset_4xx_watchdog();
+#endif /* CONFIG_WATCHDOG */
+}
+
+/*
+ * initialize higher level parts of CPU like time base and timers
+ */
+int cpu_init_r (void)
+{
+#ifdef CONFIG_405GP
+ DECLARE_GLOBAL_DATA_PTR;
+
+ bd_t *bd = gd->bd;
+ unsigned long reg;
+
+ /*
+ * Write Ethernetaddress into on-chip register
+ */
+ reg = 0x00000000;
+ reg |= bd->bi_enetaddr[0]; /* set high address */
+ reg = reg << 8;
+ reg |= bd->bi_enetaddr[1];
+ out32 (EMAC_IAH, reg);
+
+ reg = 0x00000000;
+ reg |= bd->bi_enetaddr[2]; /* set low address */
+ reg = reg << 8;
+ reg |= bd->bi_enetaddr[3];
+ reg = reg << 8;
+ reg |= bd->bi_enetaddr[4];
+ reg = reg << 8;
+ reg |= bd->bi_enetaddr[5];
+ out32 (EMAC_IAL, reg);
+#endif /* CONFIG_405GP */
+ return (0);
+}
diff --git a/cpu/sa1100/cpu.c b/cpu/sa1100/cpu.c
new file mode 100644
index 0000000..370ea6c
--- /dev/null
+++ b/cpu/sa1100/cpu.c
@@ -0,0 +1,147 @@
+/*
+ * (C) Copyright 2002
+ * Sysgo Real-Time Solutions, GmbH <www.elinos.com>
+ * Marius Groeger <mgroeger@sysgo.de>
+ *
+ * (C) Copyright 2002
+ * Sysgo Real-Time Solutions, GmbH <www.elinos.com>
+ * Alex Zuepke <azu@sysgo.de>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+/*
+ * CPU specific code
+ */
+
+#include <common.h>
+#include <command.h>
+
+int cpu_init (void)
+{
+ /*
+ * setup up stack if necessary
+ */
+#ifdef CONFIG_USE_IRQ
+ IRQ_STACK_START = _armboot_end +
+ CONFIG_STACKSIZE + CONFIG_STACKSIZE_IRQ - 4;
+ FIQ_STACK_START = IRQ_STACK_START + CONFIG_STACKSIZE_FIQ;
+ _armboot_real_end = FIQ_STACK_START + 4;
+#else
+ _armboot_real_end = _armboot_end + CONFIG_STACKSIZE;
+#endif
+ return (0);
+}
+
+int cleanup_before_linux (void)
+{
+ /*
+ * this function is called just before we call linux
+ * it prepares the processor for linux
+ *
+ * just disable everything that can disturb booting linux
+ */
+
+ unsigned long i;
+
+ disable_interrupts ();
+
+ /* turn off I-cache */
+ asm ("mrc p15, 0, %0, c1, c0, 0":"=r" (i));
+ i &= ~0x1000;
+ asm ("mcr p15, 0, %0, c1, c0, 0": :"r" (i));
+
+ /* flush I-cache */
+ asm ("mcr p15, 0, %0, c7, c5, 0": :"r" (i));
+
+ return (0);
+}
+
+int do_reset (cmd_tbl_t *cmdtp, int flag, int argc, char *argv[])
+{
+ extern void reset_cpu (ulong addr);
+
+ printf ("resetting ...\n");
+
+ udelay (50000); /* wait 50 ms */
+ disable_interrupts ();
+ reset_cpu (0);
+
+ /*NOTREACHED*/
+ return (0);
+}
+
+/* taken from blob */
+void icache_enable (void)
+{
+ register u32 i;
+
+ /* read control register */
+ asm ("mrc p15, 0, %0, c1, c0, 0":"=r" (i));
+
+ /* set i-cache */
+ i |= 0x1000;
+
+ /* write back to control register */
+ asm ("mcr p15, 0, %0, c1, c0, 0": :"r" (i));
+}
+
+void icache_disable (void)
+{
+ register u32 i;
+
+ /* read control register */
+ asm ("mrc p15, 0, %0, c1, c0, 0":"=r" (i));
+
+ /* clear i-cache */
+ i &= ~0x1000;
+
+ /* write back to control register */
+ asm ("mcr p15, 0, %0, c1, c0, 0": :"r" (i));
+
+ /* flush i-cache */
+ asm ("mcr p15, 0, %0, c7, c5, 0": :"r" (i));
+}
+
+int icache_status (void)
+{
+ register u32 i;
+
+ /* read control register */
+ asm ("mrc p15, 0, %0, c1, c0, 0":"=r" (i));
+
+ /* return bit */
+ return (i & 0x1000);
+}
+
+/* we will never enable dcache, because we have to setup MMU first */
+void dcache_enable (void)
+{
+ return;
+}
+
+void dcache_disable (void)
+{
+ return;
+}
+
+int dcache_status (void)
+{
+ return 0; /* always off */
+}