powerpc/T104xD4RDB: Add T104xD4RDB boards support
T1040D4RDB is a Freescale reference board that hosts the T1040 SoC.
T1040D4RDB is re-designed T1040RDB board with following changes :
- Support of DDR4 memory
- Support of 0x66 serdes protocol which can support following interfaces
- 2 RGMII's on DTSEC4, DTSEC5
- 1 SGMII on DTSEC3
- Support of QE-TDM
Similarily T1042D4RDB is a Freescale reference board that hosts the T1040
SoC. T1042D4RDB is re-designed T1042RDB board with following changes :
- Support of DDR4 memory
- Support for 0x86 serdes protocol which can support following interfaces
- 2 RGMII's on DTSEC4, DTSEC5
- 3 SGMII on DTSEC1, DTSEC2 & DTSEC3
- Support of DIU
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@freescale.com>
Signed-off-by: Wang Dongsheng <dongsheng.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
diff --git a/board/freescale/t104xrdb/MAINTAINERS b/board/freescale/t104xrdb/MAINTAINERS
index 13d9be9..32e044f 100644
--- a/board/freescale/t104xrdb/MAINTAINERS
+++ b/board/freescale/t104xrdb/MAINTAINERS
@@ -6,7 +6,13 @@
F: configs/T1040RDB_defconfig
F: configs/T1040RDB_NAND_defconfig
F: configs/T1040RDB_SPIFLASH_defconfig
+F: configs/T1040D4RDB_defconfig
+F: configs/T1040D4RDB_NAND_defconfig
+F: configs/T1040D4RDB_SPIFLASH_defconfig
F: configs/T1042RDB_defconfig
+F: configs/T1042D4RDB_defconfig
+F: configs/T1042D4RDB_NAND_defconfig
+F: configs/T1042D4RDB_SPIFLASH_defconfig
F: configs/T1042RDB_PI_defconfig
F: configs/T1042RDB_PI_NAND_defconfig
F: configs/T1042RDB_PI_SPIFLASH_defconfig
@@ -15,6 +21,8 @@
#M: -
S: Maintained
F: configs/T1040RDB_SDCARD_defconfig
+F: configs/T1040D4RDB_SDCARD_defconfig
+F: configs/T1042D4RDB_SDCARD_defconfig
F: configs/T1042RDB_PI_SDCARD_defconfig
T1040RDB_SECURE_BOOT BOARD
diff --git a/board/freescale/t104xrdb/README b/board/freescale/t104xrdb/README
index ac95b5e..b9d2212 100644
--- a/board/freescale/t104xrdb/README
+++ b/board/freescale/t104xrdb/README
@@ -12,6 +12,17 @@
(a personality of T1040 SoC). The board is similar to T1040RDB but is
designed specially with low power features targeted for Printing Image Market.
+The T1040D4RDB is a Freescale reference board that hosts the T1040 SoC.
+The board is re-designed T1040RDB board with following changes :
+ - Support of DDR4 memory and some enhancements
+
+The T1042D4RDB is a Freescale reference board that hosts the T1042 SoC.
+The board is re-designed T1040RDB board with following changes :
+ - Support of DDR4 memory
+ - Support for 0x86 serdes protocol which can support following interfaces
+ - 2 RGMII's on DTSEC4, DTSEC5
+ - 3 SGMII on DTSEC1, DTSEC2 & DTSEC3
+
Basic difference's among T1040RDB, T1042RDB_PI, T1042RDB
-------------------------------------------------------------------------
Board Si Protocol Targeted Market
@@ -19,6 +30,8 @@
T1040RDB T1040 0x66 Networking
T1040RDB T1042 0x86 Networking
T1042RDB_PI T1042 0x06 Printing & Imaging
+T1040D4RDB T1040 0x66 Networking
+T1042D4RDB T1042 0x86 Networking
T1040 SoC Overview
@@ -70,7 +83,6 @@
T1040 SoC Personalities
-------------------------
-
T1022 Personality:
T1022 is a reduced personality of T1040 with less core/clusters.
@@ -268,8 +280,13 @@
Please note QE Firmware is only valid for T1040RDB
-Switch Settings: (ON is 0, OFF is 1)
-===============
+Switch Settings for T104xRDB boards: (ON is 0, OFF is 1)
+==========================================================
+NOR boot SW setting:
+SW1: 00010011
+SW2: 10111011
+SW3: 11100001
+
NAND boot SW setting:
SW1: 10001000
SW2: 00111011
@@ -284,3 +301,67 @@
SW1: 00100000
SW2: 00111011
SW3: 11100001
+
+Switch Settings for T104xD4RDB boards: (ON is 0, OFF is 1)
+=============================================================
+NOR boot SW setting:
+SW1: 00010011
+SW2: 10111001
+SW3: 11100001
+
+NAND boot SW setting:
+SW1: 10001000
+SW2: 00111001
+SW3: 11110001
+
+SPI boot SW setting:
+SW1: 00100010
+SW2: 10111001
+SW3: 11100001
+
+SD boot SW setting:
+SW1: 00100000
+SW2: 00111001
+SW3: 11100001
+
+PBL-based image generation
+==========================
+Changes only the required register bit in in PBI commands.
+
+Provides reference code which might needs some
+modification as per requirement.
+example:
+By default PBI_SRC=14 (which is for IFC-NAND/NOR) in rcw.cfg file
+which needs to be changed for SPI and SD.
+
+For SD-boot
+==============
+1. Set RCW[192:195], PBI_SRC bits as 6 in RCW file (t1040d4_rcw.cfg type files)
+
+example:
+ RCW file: board/freescale/t104xrdb/t1040d4_rcw.cfg
+
+Change
+66000002 40000002 ec027000 01000000
+to
+66000002 40000002 6c027000 01000000
+
+2. SD does not support flush so remove flush from pbl, make changes in
+ tools/pblimage.c file, Update value of pbl_end_cmd[0] = 0x09138000
+ with 0x091380c0
+
+For SPI-boot
+==============
+1. Set RCW[192:195], PBI_SRC bits as 5 in RCW file (t1040d4_rcw.cfg type files)
+
+example:
+ RCW file: board/freescale/t104xrdb/t1040d4_rcw.cfg
+
+Change
+66000002 40000002 ec027000 01000000
+to
+66000002 40000002 5c027000 01000000
+
+2. SPI does not support flush so remove flush from pbl, make changes in
+ tools/pblimage.c file, Update value of pbl_end_cmd[0] = 0x09138000
+ with 0x091380c0
diff --git a/board/freescale/t104xrdb/cpld.c b/board/freescale/t104xrdb/cpld.c
index df0e348..0ce4e47 100644
--- a/board/freescale/t104xrdb/cpld.c
+++ b/board/freescale/t104xrdb/cpld.c
@@ -69,7 +69,11 @@
printf("int_status = 0x%02x\n", CPLD_READ(int_status));
printf("flash_ctl_status = 0x%02x\n", CPLD_READ(flash_ctl_status));
printf("fan_ctl_status = 0x%02x\n", CPLD_READ(fan_ctl_status));
+#if defined(CONFIG_T104XD4RDB)
+ printf("int_mask = 0x%02x\n", CPLD_READ(int_mask));
+#else
printf("led_ctl_status = 0x%02x\n", CPLD_READ(led_ctl_status));
+#endif
printf("sfp_ctl_status = 0x%02x\n", CPLD_READ(sfp_ctl_status));
printf("misc_ctl_status = 0x%02x\n", CPLD_READ(misc_ctl_status));
printf("boot_override = 0x%02x\n", CPLD_READ(boot_override));
diff --git a/board/freescale/t104xrdb/cpld.h b/board/freescale/t104xrdb/cpld.h
index 0da9a01..2fb4105 100644
--- a/board/freescale/t104xrdb/cpld.h
+++ b/board/freescale/t104xrdb/cpld.h
@@ -21,7 +21,11 @@
u8 int_status; /* 0x12 - Interrupt status Register */
u8 flash_ctl_status; /* 0x13 - Flash control and status register */
u8 fan_ctl_status; /* 0x14 - Fan control and status register */
+#if defined(CONFIG_T104XD4RDB)
+ u8 int_mask; /* 0x15 - Interrupt mask Register */
+#else
u8 led_ctl_status; /* 0x15 - LED control and status register */
+#endif
u8 sfp_ctl_status; /* 0x16 - SFP control and status register */
u8 misc_ctl_status; /* 0x17 - Miscellanies ctrl & status register*/
u8 boot_override; /* 0x18 - Boot override register */
@@ -38,3 +42,5 @@
#define CPLD_READ(reg) cpld_read(offsetof(struct cpld_data, reg))
#define CPLD_WRITE(reg, value)\
cpld_write(offsetof(struct cpld_data, reg), value)
+#define MISC_CTL_SG_SEL 0x80
+#define MISC_CTL_AURORA_SEL 0x02
diff --git a/board/freescale/t104xrdb/ddr.c b/board/freescale/t104xrdb/ddr.c
index e1148e5..cf79d2d 100644
--- a/board/freescale/t104xrdb/ddr.c
+++ b/board/freescale/t104xrdb/ddr.c
@@ -75,7 +75,11 @@
* Factors to consider for half-strength driver enable:
* - number of DIMMs installed
*/
+#ifdef CONFIG_SYS_FSL_DDR4
+ popts->half_strength_driver_enable = 1;
+#else
popts->half_strength_driver_enable = 0;
+#endif
/*
* Write leveling override
*/
@@ -91,8 +95,14 @@
popts->zq_en = 1;
/* DHC_EN =1, ODT = 75 Ohm */
+#ifdef CONFIG_SYS_FSL_DDR4
+ popts->ddr_cdr1 = DDR_CDR1_DHC_EN | DDR_CDR1_ODT(DDR_CDR_ODT_120OHM);
+ popts->ddr_cdr2 = DDR_CDR2_ODT(DDR_CDR_ODT_120OHM) |
+ DDR_CDR2_VREF_OVRD(70); /* Vref = 70% */
+#else
popts->ddr_cdr1 = DDR_CDR1_DHC_EN | DDR_CDR1_ODT(DDR_CDR_ODT_75ohm);
popts->ddr_cdr2 = DDR_CDR2_ODT(DDR_CDR_ODT_75ohm);
+#endif
}
#if defined(CONFIG_DEEP_SLEEP)
diff --git a/board/freescale/t104xrdb/ddr.h b/board/freescale/t104xrdb/ddr.h
index ab1c32d..b9c02f7 100644
--- a/board/freescale/t104xrdb/ddr.h
+++ b/board/freescale/t104xrdb/ddr.h
@@ -28,6 +28,9 @@
* num| hi| rank| clk| wrlvl | wrlvl
* ranks| mhz| GB |adjst| start | ctl2
*/
+#ifdef CONFIG_SYS_FSL_DDR4
+ {2, 1600, 4, 4, 6, 0x07090A0c, 0x0e0f100a},
+#elif defined(CONFIG_SYS_FSL_DDR3)
{2, 833, 4, 4, 6, 0x06060607, 0x08080807},
{2, 833, 0, 4, 6, 0x06060607, 0x08080807},
{2, 1350, 4, 4, 7, 0x0708080A, 0x0A0B0C09},
@@ -40,10 +43,14 @@
{1, 1350, 0, 4, 7, 0x0708080A, 0x0A0B0C09},
{1, 1666, 4, 4, 7, 0x0808090B, 0x0C0D0E0A},
{1, 1666, 0, 4, 7, 0x0808090B, 0x0C0D0E0A},
+#else
+#error DDR type not defined
+#endif
{}
};
+#endif
+
static const struct board_specific_parameters *udimms[] = {
udimm0,
};
-#endif
diff --git a/board/freescale/t104xrdb/eth.c b/board/freescale/t104xrdb/eth.c
index 7581a4cd..71d0457 100644
--- a/board/freescale/t104xrdb/eth.c
+++ b/board/freescale/t104xrdb/eth.c
@@ -43,9 +43,11 @@
int idx = i - FM1_DTSEC1;
switch (fm_info_get_enet_if(i)) {
-#ifdef CONFIG_T1040RDB
+#if defined(CONFIG_T1040RDB) || defined(CONFIG_T1040D4RDB)
case PHY_INTERFACE_MODE_SGMII:
- /* T1040RDB only supports SGMII on DTSEC3 */
+ /* T1040RDB & T1040D4RDB only supports SGMII on
+ * DTSEC3
+ */
fm_info_set_phy_address(FM1_DTSEC3,
CONFIG_SYS_SGMII1_PHY_ADDR);
break;
@@ -60,6 +62,20 @@
CONFIG_SYS_SGMII1_PHY_ADDR);
break;
#endif
+#ifdef CONFIG_T1042D4RDB
+ case PHY_INTERFACE_MODE_SGMII:
+ /* T1042D4RDB supports SGMII on DTSEC1, DTSEC2
+ * & DTSEC3
+ */
+ if (FM1_DTSEC1 == i)
+ phy_addr = CONFIG_SYS_SGMII1_PHY_ADDR;
+ if (FM1_DTSEC2 == i)
+ phy_addr = CONFIG_SYS_SGMII2_PHY_ADDR;
+ if (FM1_DTSEC3 == i)
+ phy_addr = CONFIG_SYS_SGMII3_PHY_ADDR;
+ fm_info_set_phy_address(i, phy_addr);
+ break;
+#endif
case PHY_INTERFACE_MODE_RGMII:
if (FM1_DTSEC4 == i)
phy_addr = CONFIG_SYS_RGMII1_PHY_ADDR;
diff --git a/board/freescale/t104xrdb/t1040d4_rcw.cfg b/board/freescale/t104xrdb/t1040d4_rcw.cfg
new file mode 100644
index 0000000..c1034b3
--- /dev/null
+++ b/board/freescale/t104xrdb/t1040d4_rcw.cfg
@@ -0,0 +1,7 @@
+#PBL preamble and RCW header
+aa55aa55 010e0100
+# serdes protocol 0x66
+0c18000e 0e000000 00000000 00000000
+66000002 40000002 ec027000 01000000
+00000000 00000000 00000000 00030810
+00000000 0342580f 00000000 00000000
diff --git a/board/freescale/t104xrdb/t1042d4_rcw.cfg b/board/freescale/t104xrdb/t1042d4_rcw.cfg
new file mode 100644
index 0000000..9e0ee27
--- /dev/null
+++ b/board/freescale/t104xrdb/t1042d4_rcw.cfg
@@ -0,0 +1,7 @@
+#PBL preamble and RCW header
+aa55aa55 010e0100
+# serdes protocol 0x86
+0c18000e 0e000000 00000000 00000000
+86000002 40000002 ec027000 01000000
+00000000 00000000 00000000 00030810
+00000000 0342500f 00000000 00000000
diff --git a/board/freescale/t104xrdb/t104xrdb.c b/board/freescale/t104xrdb/t104xrdb.c
index 9cd5e15..c4b658d 100644
--- a/board/freescale/t104xrdb/t104xrdb.c
+++ b/board/freescale/t104xrdb/t104xrdb.c
@@ -28,7 +28,11 @@
struct cpu_type *cpu = gd->arch.cpu;
u8 sw;
+#ifdef CONFIG_T104XD4RDB
+ printf("Board: %sD4RDB\n", cpu->name);
+#else
printf("Board: %sRDB\n", cpu->name);
+#endif
printf("Board rev: 0x%02x CPLD ver: 0x%02x, ",
CPLD_READ(hw_ver), CPLD_READ(sw_ver));
@@ -91,6 +95,34 @@
int misc_init_r(void)
{
+ ccsr_gur_t __iomem *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
+ u32 srds_s1;
+
+ srds_s1 = in_be32(&gur->rcwsr[4]) >> 24;
+
+ printf("SERDES Reference : 0x%X\n", srds_s1);
+
+ /* select SGMII*/
+ if (srds_s1 == 0x86)
+ CPLD_WRITE(misc_ctl_status, CPLD_READ(misc_ctl_status) |
+ MISC_CTL_SG_SEL);
+
+ /* select SGMII and Aurora*/
+ if (srds_s1 == 0x8E)
+ CPLD_WRITE(misc_ctl_status, CPLD_READ(misc_ctl_status) |
+ MISC_CTL_SG_SEL | MISC_CTL_AURORA_SEL);
+
+#if defined(CONFIG_T1040D4RDB)
+ /* Mask all CPLD interrupt sources, except QSGMII interrupts */
+ if (CPLD_READ(sw_ver) < 0x03) {
+ debug("CPLD SW version 0x%02x doesn't support int_mask\n",
+ CPLD_READ(sw_ver));
+ } else {
+ CPLD_WRITE(int_mask, CPLD_INT_MASK_ALL &
+ ~(CPLD_INT_MASK_QSGMII1 | CPLD_INT_MASK_QSGMII2));
+ }
+#endif
+
return 0;
}